# AD 51-27-01: Engine Mount Replacement - Type: Airworthiness directive - Status: Current - Products: Scotts-Bell 47 47, 47B, 47B3, 47D, 47D1, 47E, 47G, 47G-2, 47G-2A, 47G-2A-1, 47G-3, 47G-3B and 12 more - Superseded by: Nothing supersedes this AD - Product type: Aircraft, Rotorcraft - Registered aircraft: 490 may be affected, by airframe or engine model (OpenAirDocs) - FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/F6BD42B0B5BD862086256A34004E8C86.0001 - DRS record last changed: May 30, 2024 - Page: https://openairdocs.org/ad/51-27-01 ## The airworthiness directive 51-27-01 BELL: Applies to All Model 47 Helicopters Incorporating Engine Mount Assembly P/N 47-612-111-1 or -5. Compliance required as indicated. 1. Compliance required daily after first 300-hour inspection. (a) Remove paint from welds in tube cluster at mount housing at both sides of mount assembly. Use solvent to remove paint. (b) With the engine mount under load, either by operating the engine with maximum collective pitch without becoming airborne, or by placing equivalent pilot and passenger weights in the seat and hoisting helicopter until wheels are clear of ground (or any equivalent loading means), inspect the outboard surface of welds with at least a 10-power magnifying glass and the inboard surfaces of welds with an inspection mirror (use magnifying if available). Give particular attention to forward tube in left cluster (from top of mount to housing) and aft tube in right cluster. Oil appearing on surface of weld or tube after cleaning is evidenceof a crack and must be examined carefully. Replace mount if crack is found. (c) Clean welds in upper forward tube (under collective pitch disc bracket) with a cloth. Carefully inspect welds under disc bracket for cracks using a flashlight and mirror. Give particular attention to weld which joins diagonal tube (right side) to forward tube. Replace mount immediately if a crack is found in these areas. Apply grease or other corrosion preventive on areas where paint has been removed. 2. Compliance required at each 600 hours of engine mount service. Replace engine mount assembly after 600 hours of operation have been accumulated. (Bell Service Bulletin No. 74, revised February 2, 1953, covers this same subject.) This supersedes AD 51-23-02. ## Affected data sheets (3) (OpenAirDocs) The type certificate data sheets whose models the AD names. - [TCDS 2H3](https://openairdocs.org/tcds/2H3): Scott's-Bell 47 Inc; names 11 of 11 models: 47G-2A, 47G-3B, 47G-3, 47G-4A, 47G-5A, 47G-5, 47G-3B-2A, 47G-3B-2… - [TCDS H-1](https://openairdocs.org/tcds/H-1): Scott's-Bell 47 Inc; names 9 of 9 models: 47H-1, 47B, 47B3, 47D1, 47D, 47G-2, 47G, 47… - [TCDS 2H1](https://openairdocs.org/tcds/2H1): Scott's-Bell 47 Inc; names 4 of 4 models: 47K, 47J-2, 47J-2A, 47J ## Registered aircraft it may apply to (OpenAirDocs) Matched by airframe and engine model; the AD's applicability may narrow it by serial number, part number or equipment. - Aircraft: 490 (490 by airframe model, 0 by engine model) - Makers: Bell 476, Bell-K-Copter 3, Bell Kitz Kopters 1, Bell-Allied Helicopter 1, Bell-Carson 1, Bell-Huddleston And Wilson 1, Bell-Intermountain 1, Bell-Olympic Helicopters 1, Bell-Shippey 1, Bell-Tellijohn 1 Models with the most aircraft: - [Bell 47G-2](https://openairdocs.org/model/bell-47g-2): 87 aircraft (airframe model) - [Bell 47G-3B-1](https://openairdocs.org/model/bell-47g-3b-1): 86 aircraft (airframe model) - [Bell 47G](https://openairdocs.org/model/bell-47g): 55 aircraft (airframe model) - [Bell 47D1](https://openairdocs.org/model/bell-47d1): 47 aircraft (airframe model) - [Bell 47G-5](https://openairdocs.org/model/bell-47g-5): 40 aircraft (airframe model) - [Bell 47G-3B-2](https://openairdocs.org/model/bell-47g-3b-2): 26 aircraft (airframe model) - [Bell 47G-4A](https://openairdocs.org/model/bell-47g-4a): 20 aircraft (airframe model) - [Bell 47G-2A](https://openairdocs.org/model/bell-47g-2a): 19 aircraft (airframe model) - [Bell 47G-5A](https://openairdocs.org/model/bell-47g-5a): 19 aircraft (airframe model) - [Bell 47G-3B](https://openairdocs.org/model/bell-47g-3b): 15 aircraft (airframe model) - [Bell 47G-2A-1](https://openairdocs.org/model/bell-47g-2a-1): 13 aircraft (airframe model) - [Bell 47G-4](https://openairdocs.org/model/bell-47g-4): 13 aircraft (airframe model) - [Bell 47G3B2A](https://openairdocs.org/model/bell-47g3b2a): 7 aircraft (airframe model) - [Bell 47H-1](https://openairdocs.org/model/bell-47h-1): 6 aircraft (airframe model) - [Bell 47J](https://openairdocs.org/model/bell-47j): 6 aircraft (airframe model) - [Bell 47J-2](https://openairdocs.org/model/bell-47j-2): 6 aircraft (airframe model) - [Bell 47J-2A](https://openairdocs.org/model/bell-47j-2a): 5 aircraft (airframe model) - [Bell 47D](https://openairdocs.org/model/bell-47d): 4 aircraft (airframe model) - [Bell-K-Copter 47G](https://openairdocs.org/model/bell-k-copter-47g): 2 aircraft (airframe model) - [Bell 47B](https://openairdocs.org/model/bell-47b): 1 aircraft (airframe model) All 35 models: https://openairdocs.org/ad/51-27-01/models.md Every aircraft: https://openairdocs.org/ad/51-27-01/aircraft.md Its text cites no advisory circulars or STCs. --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.