# AD 83-20-04: Horizontal Stabilizer Rear Spar Caps - Type: Airworthiness directive - Status: Current - Products: Boeing DC-6, DC-6A, DC-6B, Navy R6D-1, Navy R6D-1Z and USAF C-118A - Effective: October 19, 1983 - Superseded by: Nothing supersedes this AD - Product type: Aircraft, Large airplane - Amendment: 39-4740 - Registered aircraft: 17 may be affected, by airframe or engine model (OpenAirDocs) - FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/BB31F0EACDE584F6862569F2006A0E00.0001 - DRS record last changed: May 30, 2024 - Page: https://openairdocs.org/ad/83-20-04 ## The airworthiness directive 83-20-04 McDONNELL DOUGLAS: Amendment 39-4740. Applies to McDonnell Douglas Model DC-6, -6A, -6B, R6D (Navy), and C118 (USAF) series airplanes, certificated in all categories. Compliance required as indicated, unless previously accomplished. To detect cracks and prevent failure of the horizontal stabilizer rear spar caps accomplish the following: A. Within the next 30 days after the effective date of this AD, unless already accomplished, inspect and repair, if necessary, the horizontal stabilizer upper and lower rear spar cap attach fittings on both sides of station 63 in accordance with the Accomplishment Instructions of McDonnell Douglas Service Rework Drawing J060265 "N/C" dated July 29, 1983, hereinafter referred to as Rework Drawing, or later revisions approved by the Manager, Los Angeles Aircraft Certification Office, FAA, Northwest Mountain Region, as follows: 1. If no cracks are found in the rear spar attach fittings, apply primer and lacquer top coat(lacquer top coat optional). Apply LPS-3 corrosion inhibiting oil, or equivalent when approved by the Manager, Los Angeles Aircraft Certification Office, FAA, Northwest Mountain Region, throughout the attach fitting (bathtub area) and reinstall the bolt per the Rework Drawing. Conduct repetitive inspections per the Rework Drawing at intervals not to exceed 12 calendar months. 2. If a crack is found equal to or exceeding 1/2" at location A, 3" at location B, or 6" at location C as defined in figure 2 of the Rework Drawing, accomplish the repair in (a) or (b) below, prior to further flight: (a) If the crack is inboard of station 63, repair in accordance with the Accomplishment Instructions of the Rework Drawing. (b) If the crack is outboard of station 63, repair per the McDonnell Douglas DC-6 Structural Repair Manual, Tail Group, Page 138, Figure 134, dated October 15, 1952. 3. If a crack is found that is less than 1/2" at location A, 3" at location B, or 6" at location C, repetitively inspect per the Rework Drawing at intervals not to exceed: (a) for location A: 7 calendar days, or prior to further flight, whichever occurs later. (b) for location B: 14 calendar days, or prior to further flight, whichever occurs later. (c) for location C: 21 calendar days, or prior to further flight, whichever occurs later. B. Repairs per Paragraph 2, above, constitutes terminating action for the repetitive inspections required by this AD only at those locations repaired. C. If more than one crack is found, repair all cracked areas as specified in Paragraphs A. 2(a) and/or 2(b), above. D. Alternate means of compliance which provide an equivalent level of safety may be used when approved by the Manager, Los Angeles Aircraft Certification Office, FAA, Northwest Mountain Region. E. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base to comply with the repair requirements of this AD when approved by the Manager, Los Angeles Aircraft Certification Office, FAA, Northwest Mountain Region. This Amendment becomes effective October 19, 1983. ## Affected data sheets (3) (OpenAirDocs) The type certificate data sheets whose models the AD names. - [TCDS 6A3](https://openairdocs.org/tcds/6A3): The Boeing Company; names 3 of 3 models: DC-6A, USAF C-118A, Navy R6D-1 - [TCDS 6A4](https://openairdocs.org/tcds/6A4): The Boeing Company; names 2 of 2 models: Navy R6D-1Z, DC-6B - [TCDS A-781](https://openairdocs.org/tcds/A-781): The Boeing Company; names 1 of 1 models: DC-6 ## Registered aircraft it may apply to (OpenAirDocs) Matched by airframe and engine model; the AD's applicability may narrow it by serial number, part number or equipment. - Aircraft: 17 (17 by airframe model, 0 by engine model) - Makers: Douglas 17 Models with the most aircraft: - [Douglas DC-6B](https://openairdocs.org/model/douglas-dc-6b): 9 aircraft (airframe model) - [Douglas DC-6A](https://openairdocs.org/model/douglas-dc-6a): 7 aircraft (airframe model) - [Douglas DC-6](https://openairdocs.org/model/douglas-dc-6): 1 aircraft (airframe model) All 3 models: https://openairdocs.org/ad/83-20-04/models.md Every aircraft: https://openairdocs.org/ad/83-20-04/aircraft.md Its text cites no advisory circulars or STCs. --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.