AIRWORTHINESS DIRECTIVES EMERGENCY RULES: 2008-22-53
CITATION:
PAGE NUMBER:
DOCKET NUMBER: Unknown
AMENDMENT:
AD NUMBER: 2008-22-53
SUBJECT HEADING: MD Helicopters, Inc. Model MD900 helicopters
ACTION:
SUMMARY: This superseding Emergency Airworthiness Directive (EAD) is prompted by 4 occurrences on the MD900 helicopters with failed left Vertical Stabilizer Control System (VSCS) adapter tubes where the vertical stabilizer became uncontrollable, resulting in reduced yaw control of the helicopter. There were no injuries, but in one occurrence, due to the high speed quick yaw, the helicopter lost a window and a door. The actions specified by this EAD are intended to prevent a reduction of yaw control and subsequent loss of control of the helicopter.
We have reviewed MDHI Service Bulletin (SB) SB900-110, dated October 17, 2008. The SB specifies the following:
- Making a placard that states “AIRSPEED LIMIT 100 KIAS OR VNE, WHICHEVER IS LESS. VMC FLIGHT ONLY, AUTOPILOT OFF.”
- Installing a placard on the instrument panel in view of the pilot.
- Making a record in the compliance section of the Rotorcraft Log Book that the SB has been completed.
- Operating the helicopter as specified in the applicable Rotorcraft Flight Manual Airspeed Limitation Section for helicopter operation.
The SB also includes the following Notes:
- Stronger replacement tube adapters with a new part number are in the FAA approval process. Owners and operators will be notified when the new adapter tubes are available by a revision to the service bulletin.
- If there is an anti-torque system malfunction, de-energize the VSCS on final approach to a run on landing. Refer to Rotorcraft Flight Manual Emergency Procedures for Anti-torque Failure Complete Loss of Thrust and Fixed Thruster Setting.
- Do an inspection before and after each flight to make sure vertical stabilizers are in the correct position and control linkages are attached. To check control linkages, apply light pressure with your hand to the trailing edge of left and right vertical stabilizer in the inboard and outboard direction. No more than 0.125 in. (3.175 mm) movement permitted.
On August 20, 2008, we issued EAD 2008-18-51 for 500N, 600N, and MD900 helicopters. EAD 2008-18-51 was prompted by reports that two MD900 helicopters experienced failed VSCS adapter tubes. In one case, the helicopter experienced an uncommanded yaw, resulting in loss of a window and a door. The EAD required several actions related to the YSAS for the Model 500N and 600N helicopters and related to the VSCS for the Model MD900 helicopters.
After we issued EAD 2008-18-51, we discovered that pulling the circuit breaker per the EAD caused impaired directional control, which could result in loss of control of the helicopter. Therefore, on August 27, 2008, we issued superseding EAD 2008-18-52, which requires, for Model 500N, 600N and MD900 helicopters, turning OFF the VSCS or the YSAS instead of pulling the circuit breakers and installing placards that limit airspeed to 100 KTS or VNE, whichever is less. For the Model MD900 helicopters, limiting flight to VFR, prohibiting use of the autopilot, and making changes to the Emergency Procedures and Airworthiness (sic) Limitations sections of the Rotorcraft Flight Manual (RFM) are also required. For all of the helicopter models, EAD 2008-18-52 requires, within 45 days, terminating action by replacing the adapter tube with an airworthy adapter tube that has a date stamp of August 15, 2008 or later, and then removing the placards, removing the AD limitation changes from the RFM, and returning all switches and circuit breakers to their normal positions.
Since the issuance of EAD 2008-18-52, we have had additional occurrences of failed adapter tubes on the MD900 helicopters. The replacement adapter tube that was terminating action for the requirements of EAD 2008-18-52 failed on 2 of the MD900 helicopters. Based on these additional adapter tube failures on the MD900 helicopters, we have determined that additional corrective action is required to correct the unsafe condition for the MD900 helicopters. Therefore, we are separating the AD actions and issuing 2 superseding ADs; 2008-22-52 for the 500N and 600N helicopters, and 2008-22-53 for the MD900 helicopters.
This superseding EAD 2008-22-53 differs from EAD 2008-18-52 in that we have made minor editorial changes and other changes as follows:
- We do not include any serial numbers in the applicability because this unsafe condition can occur on any helicopter with the affected adapter tube installed.
- We require both VSCS switches to be turned ON to reduce pilot workload under normal flight conditions and to help control the helicopter in the event of an adapter tube failure until the helicopter is on final approach.
- We do not provide a terminating action because the cause of the failures is still being investigated.
This EAD differs from the SB in that it does not require, before and after each flight, an inspection of the vertical stabilizer and control linkages because we have determined that limiting the airspeed to 100 KIAS or VNE, whichever is less, will allow the continued safe operation of the helicopter in the event of an in-flight failure of the adapter tube. Also, this EAD differs from the SB in that we require flight under VFR instead of VMC because the master minimum equipment list does not allow dispatch of the helicopter under IFR with an inoperative autopilot.
This EAD is an interim action that is intended to provide the continued safe operation of the helicopter in the event of an in-flight failure of the adapter tube. MDHI is currently attempting to determine the root cause of the adapter tube failures and develop final corrective action. We anticipate additional rulemaking once MDHI determines the cause of the adapter tube failures and develops an acceptable corrective action or terminating action for the requirements of this EAD.
This unsafe condition is likely to exist or develop on other helicopters of the same type design. Therefore, this EAD requires the following before further flight:
- Turning ON both VSCS switches and turning OFF the autopilot (AP/SAS) switch after centering the trim actuators.
- Pulling and installing cable ties around certain AP/SAS circuit breakers.
- Installing a placard next to the AP/SAS master switch alerting the pilot that the autopilot has been deactivated.
- Installing a placard on the instrument panel as close as practicable to the airspeed indicator that states:
“AIRSPEED LIMIT 100 KIAS or VNE, WHICHEVER IS LESS. VFR FLIGHT ONLY, AUTOPILOT OFF.”
- Making pen and ink changes or inserting a copy of this AD into the limitations section of the rotorcraft flight manual (RFM) to revise the limitations as follows: “VNE is limited to 100 KIAS or less as determined by referring to the airspeed VNE placard already installed on the helicopter. VFR Flight Only, Autopilot Off.”
- Making pen and ink changes or inserting a copy of this AD into the limitations section of the RFM to revise the emergency procedures as follows: “If you experience an anti-torque system malfunction, turn both VSCS switches to OFF during final approach for a run-on landing.”
This rule is issued under 49 U.S.C. Section 44701 pursuant to the authority delegated to me by the Administrator, and is effective immediately upon receipt of this emergency AD.
DATES:
ADDRESSES:
FOR FURTHER INFORMATION CONTACT:
SUPPLEMENTARY INFORMATION:
REGULATORY TEXT:
2008-22-53 MD HELICOPTERS, INC.: Directorate Identifier 2008-SW-61-AD. Supersedes Emergency AD 2008-18-52, Directorate Identifier 2008-SW-52-AD.
Applicability: Model MD900 helicopters with a Vertical Stabilizer Control System (VSCS) adapter tube, part number 500N7218-1, installed, certificated in any category.
Compliance: Required before further flight, unless accomplished previously.
To prevent loss of yaw control and subsequent loss of control of the helicopter, do the following:
(a) Turn ON both VSCS switches.
(b) If installed, de-energize the autopilot (AP/SAS) as follows:
(1) Determine if the AP/SAS trim actuators are centered. If the AP/SAS trim actuators are not centered, center them.
(2) After the AP/SAS trim actuators are centered:
(i) Turn the AP/SAS MSTR switch to the OFF position.
(ii) Pull the following AP circuit breakers located on the A601 Essential Bus Circuit Breaker Panel, mounted in the cockpit console, and install a plastic cable tie on each circuit breaker to prevent accidental energizing of the circuit:
(A) AP/SAS CMPTR (CB28),
(B) AP/SAS DISC (CB29), and
(C) AP/SAS ACCEL (CB30).
(3) Install a placard next to the AP Mode Select panel that contains the AP/SAS MSTR switch stating “AP/SAS DEACTIVATED.”
(c) Install a placard on the instrument panel as close as practicable to the airspeed indicator that states:
“AIRSPEED LIMIT 100 KIAS or VNE, WHICHEVER IS LESS. VFR FLIGHT ONLY, AUTOPILOT OFF.”
(d) Make pen and ink changes or insert a copy of this AD into the limitations section of the rotorcraft flight manual (RFM) to revise the limitations as follows: “VNE is limited to 100 KIAS or less as determined by referring to the airspeed VNE placard already installed on the helicopter. VFR Flight Only, Autopilot OFF.”
(e) Make pen and ink changes or insert a copy of this AD into the limitations section of the RFM to revise the emergency procedures as follows: “If you experience an anti-torque system malfunction, turn both VSCS switches to OFF during final approach for a run-on landing.”
Note: MDHI Service Bulletin SB900N-110, dated October 17, 2008, pertains to the subject of this AD.
(f) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Contact the Manager, Los Angeles Aircraft Certification Office, FAA, ATTN: Eric D. Schrieber, Aviation Safety Engineer, Airframe Branch, 3960 Paramount Blvd., Lakewood, California 90712, telephone 562-627-5348, fax 562-627-5210, for information about previously approved alternative methods of compliance.
(g) Copies of the applicable service information may be obtained from MD Helicopters Inc., Attn: Customer Support Division, 4555 E. McDowell Rd., Mail Stop M615, Mesa, Arizona 85215-9734, telephone 1-800-388-3378, fax 480-346-6813, or on the web at www.mdhelicopters.com.
(h) Emergency AD 2008-22-53, issued October 23, 2008, becomes effective upon receipt.
FOR FURTHER INFORMATION CONTACT: Eric D. Schrieber, FAA, Los Angeles Aircraft Certification Office, Aviation Safety Engineer, Airframe Branch, 3960 Paramount Blvd., Lakewood, California 90712, telephone 562-627-5348, fax 562-627-5210.
FOOTER: Issued in Fort Worth, Texas, on October 23, 2008.
Scott A. Horn,
Acting Manager, Rotorcraft Directorate,
Aircraft Certification Service.