# NTSB CEN10LA431: Bell 47G-4A, N124SH, Rochester, MN, July 24, 2010

- Type: NTSB accident investigation
- Classification: Accident · Fatal · Limited investigation · Final report
- Date: July 24, 2010, 14:00 local (19:00 UTC)
- Place: Rochester, MN
- Coordinates: 44.04972, -92.326385 (estimated)
- Nearby events: https://openairdocs.org/map.md?lat=44.0497&lon=-92.3264&mi=10
- Phase of flight: [Maneuvering](https://openairdocs.org/ntsb-phases/450) (OpenAirDocs' grouping)
- Defining event: [Maneuvering-low-alt flying: Loss of engine power (total)](https://openairdocs.org/ntsb-events/341)
- Highest injury: Fatal
- Injuries: 1 fatal
- Status: Completed, report March 7, 2014
- Report: Approved by Office Director
- NTSB office: Central Region
- Parties: FAA Minneapolis FSDO
- NTSB case key (mKey): 76741
- NTSB case page: https://web.ntsb.gov/investigations/?ntsbnumber=CEN10LA431
- NTSB report (PDF, downloads): https://data.ntsb.gov/carol-repgen/api/Aviation/ReportMain/GenerateNewestReport/76741/pdf
- NTSB docket: https://data.ntsb.gov/Docket?ProjectID=76741
- Page: https://openairdocs.org/ntsb/CEN10LA431

## Probable cause

The total loss of engine power due to a high-cycle fatigue fracture of a first-stage compressor blade. The reason for the fracture could not be determined during postaccident examination.

## Findings

NTSB's coded findings; those marked are part of the probable cause.

- [Engine (turbine/turboprop): compressor section](https://openairdocs.org/ntsb-findings/01057230): Aircraft › Aircraft power plant · Fatigue/wear/corrosion (probable cause); cases with it: [Bell 47G-4A, 1 case](https://openairdocs.org/ntsb-findings/01057230/cases.md?model=1181031), [All aircraft, 53 cases](https://openairdocs.org/ntsb-findings/01057230/cases.md)
- [Not determined](https://openairdocs.org/ntsb-findings/05000000): Not determined › Not determined · Unknown/Not determined (probable cause); cases with it: [Bell 47G-4A, 1 case](https://openairdocs.org/ntsb-findings/05000000/cases.md?model=1181031), [All aircraft, 2,247 cases](https://openairdocs.org/ntsb-findings/05000000/cases.md)

## Sequence of events

The events NTSB coded, in order, by phase of flight. The defining event best describes what happened.

- [Maneuvering-low-alt flying: Loss of engine power (total)](https://openairdocs.org/ntsb-events/341) (defining event); cases with it: [Bell 47G-4A, 4 cases](https://openairdocs.org/ntsb-events/341/sequence.md?model=1181031), [All aircraft, 3,820 cases](https://openairdocs.org/ntsb-events/341/sequence.md)
- [Autorotation: Collision with terr/obj (non-CFIT) ](https://openairdocs.org/ntsb-events/470); cases with it: [Bell 47G-4A, 3 cases](https://openairdocs.org/ntsb-events/470/sequence.md?model=1181031), [All aircraft, 10,189 cases](https://openairdocs.org/ntsb-events/470/sequence.md)

## Analysis

A witness reported that the agricultural helicopter was refueled and that the hopper was loaded with chemical before departure. He reported that he saw the helicopter depart, that the engine sounded normal, and that the helicopter's departure and flightpath appeared normal. He then saw a "brown puff of smoke" come from the helicopter, and it subsequently descended and impacted a hill. A postaccident engine examination revealed that the compressor rotor assembly had failed. The metallurgical examination of the compressor rotor assembly revealed that a single first-stage compressor blade had fractured in high-cycle fatigue. The microstructure, hardness, and chemistry of the first-stage compressor wheel conformed to the requirements of the engineering drawing. No evidence of corrosion was found near the fracture origin. The engine was installed on the helicopter during the last annual maintenance inspection conducted 3 days before the accident. Evidence indicated that the engine was installed properly. The reason for the fracture could not be determined.

## Factual narrative

The pilot's Garmin 496 and the attaching mount were found at the accident site. The operator reported that the pilot used it for navigation, and that the pilot mounted it on the cyclic. The helicopter was a Bell 47G-4A, serial number 7599, manufactured in 1967 with a normal category airworthiness certificate. The helicopter seated three and had a maximum gross weight of 2,950 pounds. In July 2003, the helicopter was configured for agriculture and pest control, and the airworthiness certificate was changed to a restricted category. The last annual maintenance inspection was conducted on July 21, 2010. At the time of the inspection, the helicopter had a total time of 15,020.2 hours and a recording hour meter reading of 323.5 hours. The helicopter was originally equipped with a Lycoming VO-540-B1B3 reciprocating engine. On June 24, 2003, the helicopter was equipped with an Allison 250-C20B engine, in accordance with Supplemental Type Certificate (STC) SH657NW. Subsequently, Scott's Helicopter Sevices acquired the helicopter. On July 21, 2010, the operator installed a 317 horsepower Allison T63-A-700 engine, serial number AE-403309 BCEF, on the helicopter during the annual maintenance inspection. (The T63-A-700 is the military version of the commercial Allison 250-C10D engine) The engine had been removed from N3094G on March 24, 2009, and had not been in service until its installation in the accident helicopter. The engine total time was 3,782.8 hours with a time since overhaul of 2,026.8 hours at the time of the annual maintenance inspection. At the accident site, the recording hour meter reading was 328.7 hours, which indicated that the helicopter was operated for 5.2 hours since the last annual maintenance inspection. On July 24, 2010, at 1400 central daylight time, a Bell 47G-4A, N124SH, sustained substantial damage when it impacted the terrain after a loss of engine power at low altitude near Rochester, Minnesota. The commercial pilot was fatally injured. The helicopter was registered to and operated by Scotts Helicopter Services under the provisions of the 14 Code of Federal Regulations Part 137 as an agricultural flight. The helicopter was en route to a field after it had refueled and reloaded its chemical load when the accident occurred. Visual meteorological conditions prevailed at the time of the accident. No flight plan was filed. A witness, who was the spray truck driver, reported that the pilot returned from a spray run and had the helicopter refueled and the hopper filled with chemical. The witness watched it depart toward a field about a mile away. He stated that the engine sounded normal, and that there was nothing unusual about its departure or flight path. Then he saw a "brown puff of smoke" from the helicopter in-flight, and the helicopter almost immediately descended and impacted a small hill. The helicopter wreckage came to rest on the other side of the hill. There was no ground fire. The witness reported that the pilot hadperformed about 16 spray runs during the day, and that the pilot looked healthy and normal before the flight. An autopsy of the pilot was conducted on July 25, 2010, at the Mayo Clinic in Rochester, Minnesota. The "Cause of Death" was noted as "multiple blunt force injuries due to a helicopter collision." A Forensic Toxicology Fatal Accident Report was prepared by the FAA Civil Aerospace Medical Institute. The results were negative for carbon monoxide, cyanide, and ethanol. Ibuprofen was detected in the urine. At 1353, the surface weather observation at the Rochester International Airport (RST), in Rochester, Minnesota, located about 15 miles southeast of the accident site was: wind 210 degrees at 11 knots, gusting to 15 knots; visibility 10 miles; ceiling broken at 25,000 feet; temperature 33 degrees Celsius; dew point 22 degrees Celsius; altimeter 30.06 inches of mercury. The 68-year-old pilot held a commercial pilot certificate with single-engine land airplane and helicopter ratings. The pilot's second class medical certificate issued on July 13, 2010, required that the pilot "must wear corrective lenses." The pilot reported that his total flight time was about 16,000 hours with about 150 hours flown in the last six months. The operator reported that the pilot had about 4,500 hours in a Bell 47 helicopter and about 1,000 hours in single-engine airplanes. He flew his last biennial flight review in April 2010. On August 12, 2010, the engine was examined at the Rolls-Royce facility with FAA oversight. The examination of the compressor rotor assembly revealed that a single first-stage blade had fractured at approximately 1/3 span. All compressor blades exhibited extensive foreign object damage. On February 8, 2011, a metallurgical examination of the compressor and engine components was conducted at Rolls-Royce with FAA oversight. The examination revealed the following: 1. The first stage compressor wheel airfoil cracked in high cycle fatigue, initiating subsurface and emanating from a cluster of delta ferrite islands on the suction side airfoil approximately 0.36 inch outboard of the root and 0.25 inch from the leading edge. No corrosion damage was found associated with the crack origin. 2. The microstructure, hardness, and chemistry of the first stage compressor wheel conformed to the requirements of the engineering drawing. The examination of the accident site indicated that the helicopter was traveling on a northwesterly heading. The initial impact point was a found on the front side of a small hill, and it had a red paint transfer mark which was consistent with a tailboom strike. The tailboom was separated from the fuselage and was lying about 10 feet from the main wreckage located on the back side of the small hill. The main wreckage was found partially inverted on its right side, facing to the southeast. The main rotor blades were found with the main wreckage. Except for one blade was broken from the blade hub, both blades were intact andexhibited minimal impact damage to their leading edges. A Federal Aviation Administration (FAA) airworthiness inspector examined the helicopter at the accident site. Engine control continuity from the cockpit to the engine was verified. Drive train continuity from the engine to the transmission, the main rotor, the tail rotor output coupling, and the tail rotor gear box were verified. Flight control continuity of the cyclic and collective from the cockpit to the main rotor blade grips, and the tail rotor control continuity from the cockpit to the tail rotor blades were verified. A partial engine teardown was conducted during the on-site examination. The examination of the engine revealed that there were no signs of uncontained compressor, turbine, or gearbox failure. Fuel and oil filters were free of contamination. The compressor No. 1 bearing housing was torn from the No. 1 bearing struts, and the No. 1 bearing could not be rotated due to impact damage. The compressor assembly was removed from the engine. The majority of the axial compressor blades were bent opposite the direction of rotation. The turbine to compressor coupling was engaged with the no signs of damage, and no damage was noted on the compressor shaft. The compressor could be rotated by hand, but with some resistance due to the damage to the compressor blades and vanes. The combustion housing and burner can exhibited no signs of cracks, hot spots, or abnormal wear. Metal fragments were noted at the No.1 turbine stator, and the No. 1 turbine rotor blades were burned and eroded, with about 50 percent of the blade span missing. The engine was shipped to the Rolls-Royce facility in Indianapolis, Indiana, for further inspection. An AG-NAV GPS navigation unit used for agricultural spraying applications was installed on the helicopter. The unit was inspected by the manufacturer. It was determined that the hard drive was damaged and no useful information was able to be obtained from the unit. The pilot's handheld Garmin 496 GPS was found at the accident site. The unit was downloaded, but the data retrieved from the unit for the last recorded flight did not provide information that was consistent with the accident flight.

## Aircraft

- Registration: [N124SH](https://openairdocs.org/aircraft/N124SH), registered now, S/N 7599, built 1967 (OpenAirDocs)
- Reported make and model: BELL 47G-4A
- Registry model: [Bell 47G-4A](https://openairdocs.org/model/bell-47g-4a) (registry code 1181031) (OpenAirDocs)
- Registry engine: [Allison 250 SER 250HP](https://openairdocs.org/engine/allison-250-ser-250hp) (registry code 03002, turbo-shaft) (OpenAirDocs)
- Category: Helicopter
- Serial number: 7599
- Year built: 1967
- Airframe hours: 15020
- Engines: ALLISON A250-C10D 317 horsepower turbo shaft
- Damage: Substantial damage
- Flight: Aerial application, Part 137
- Operator: Scotts Helicopter Services Inc
- Registered owner: Scotts Helicopter Services Inc
- Airworthiness certificate: Special, Restricted (Special)
- Last inspection: Annual, July 15, 2010, 5.2 hours before
- Departed: Local Airstrip, IL
- Destination: Local Airstrip, IL

## Flight crew

As NTSB recorded them. NTSB leaves out names.

- Pilot; age 68; injuries: fatal; commercial; airplane ratings: single-engine land; medical: class 2, with waivers/limitations; last flight review April 20, 2010; seat: left; toxicology performed; flight hours: 16,000 total, 4,500 in this make and model, 5 in the last 24 hours

## Weather

- Conditions: Visual (VMC), Day
- Wind: 210° at 11 knots, gusting 15
- Visibility: 10 statute miles
- Lowest ceiling: 25,000 ft broken
- Temperature: 91 °F, dew point 72 °F
- Altimeter: 30.05 inHg
- Observed at: RST, 15 nm away

## FAA reports on this event (1)

The FAA's own accident and incident reports, matched to the aircraft by N-number and date (OpenAirDocs).

- [Accident 20100724042799A](https://openairdocs.org/incident/20100724042799A), Jul 24, 2010: Bell 47G-4A, Eyota, MN, Destroyed, 1 fatal. Helicopter departed truck and was enroute to spray a field when it struck a small hill. This caused substantial damage and fatal injuries to the pilot in…

## Docket (44 files)

The files NTSB released with the investigation on January 16, 2014, on NTSB's docket system: https://data.ntsb.gov/Docket?ProjectID=76741. 36.3 MB in all.

- Pilot/Operator Aircraft Accident Report, NTSB Form 6120.1 (item 1, .PDF, 2.2 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407217&FileExtension=.PDF&FileName=Pilot%2FOperator%20Aircraft%20Accident%20Report,%20NTSB%20Form%206120.1-Redacted.PDF
- FAA Interview of Scott Churchill (item 2, .PDF, 426 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406791&FileExtension=.PDF&FileName=FAA%20Interview%20of%20Scott%20Churchill-Redacted.PDF
- FAA Interview of Jim Eversman (item 3, .PDF, 406 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406790&FileExtension=.PDF&FileName=FAA%20Interview%20of%20Jim%20Eversman-Redacted.PDF
- FAA Interview of Scott Churchill - 2 (item 4, .PDF, 514 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406792&FileExtension=.PDF&FileName=FAA%20Interview%20of%20Scott%20Churchill%20-%202-Redacted.PDF
- FAA Interview of Teresa Lokken (item 5, .PDF, 394 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406793&FileExtension=.PDF&FileName=FAA%20Interview%20of%20Teresa%20Lokken-Redacted.PDF
- Letter to FAA about GPS (item 6, .PDF, 129 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406794&FileExtension=.PDF&FileName=Letter%20to%20FAA%20about%20GPS-Redacted.PDF
- Wreckage Diagram (item 7, .PDF, 302 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406795&FileExtension=.PDF&FileName=Wreckage%20Diagram-Master.PDF
- Map of Accident Site (item 8, .PDF, 1.0 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406796&FileExtension=.PDF&FileName=Map%20of%20Accident%20Site-Master.PDF
- Plot of GPS Track Data (item 9, .PDF, 831 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406797&FileExtension=.PDF&FileName=Plot%20of%20GPS%20Track%20Data-Master.PDF
- Letter from AgNav (item 10, .PDF, 153 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406798&FileExtension=.PDF&FileName=Letter%20from%20AgNav-Redacted.PDF
- FAA Inspector's Factual Observations of On-site Examination (item 11, .PDF, 307 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406937&FileExtension=.PDF&FileName=FAA%20Inspector%27s%20Factual%20Observations%20of%20On-site%20Examination-Redacted.PDF
- FAA Inspector's Factual Observations of Engine Teardown (item 12, .PDF, 430 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406938&FileExtension=.PDF&FileName=FAA%20Inspector%27s%20Factual%20Observations%20of%20Engine%20Teardown-Redacted.PDF
- Rolls-Royce Engine Investigation Report (item 13, .PDF, 430 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406896&FileExtension=.PDF&FileName=Rolls-Royce%20Engine%20Investigation%20Report-Master.PDF
- Rolls-Royce Metallugical Investigation Report - Part 1 (item 14, .PDF, 3.0 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406898&FileExtension=.PDF&FileName=Rolls-Royce%20Metallugical%20Investigation%20Report%20-%20%20Part%201-Master.PDF
- Rolls-Royce Metallugical Investigation Report - Part 2 (item 15, .PDF, 3.2 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406899&FileExtension=.PDF&FileName=Rolls-Royce%20Metallugical%20Investigation%20Report%20-%20Part%202-Master.PDF
- Maintenance Records (item 16, .PDF, 4.5 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406969&FileExtension=.PDF&FileName=Maintenance%20Records-Redacted.PDF
- Supplemental Type Certificate SH657NW (item 17, .PDF, 2.9 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406941&FileExtension=.PDF&FileName=Supplemental%20Type%20Certificate%20SH657NW-Redacted.PDF
- Type Certificat Data Sheet No - E4CE (item 18, .PDF, 4.7 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406948&FileExtension=.PDF&FileName=Type%20Certificat%20Data%20Sheet%20No%20-%20E4CE-Master.PDF
- T63-700 Engine Installation (item 19, .PDF, 67 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407085&FileExtension=.PDF&FileName=T63-700%20Engine%20Installation%20-Redacted.PDF
- FAA Letter to Rolls-Royce about Military Conversion Engines (item 20, .PDF, 196 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407088&FileExtension=.PDF&FileName=FAA%20Letter%20to%20Rolls-Royce%20about%20Military%20Conversion%20Engines-Redacted.PDF
- Rolls-Royce Response to FAA Letter about Military Conversion Engines (item 21, .PDF, 431 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407089&FileExtension=.PDF&FileName=Rolls-Royce%20Response%20to%20FAA%20Letter%20about%20Military%20Conversion%20Engines-Redacted.PDF
- NTSB Wreckage Release Documents (item 22, .PDF, 751 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406904&FileExtension=.PDF&FileName=NTSB%20Wreckage%20Release%20Documents-Redacted.PDF
- Toxicological Report (item 23, .PDF, 283 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40406915&FileExtension=.PDF&FileName=Toxicological%20Report-Redacted.PDF
- Photo 1.View of the wreckage looking to the southeast. (item 24, .PDF, 233 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407012&FileExtension=.PDF&FileName=Photo%201.View%20of%20the%20wreckage%20looking%20to%20the%20southeast.%20-Master.PDF
- Photo 2. Ground scar on the berm. (item 25, .PDF, 520 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407013&FileExtension=.PDF&FileName=Photo%202.%20Ground%20scar%20on%20the%20berm.-Master.PDF
- Photo 3. View of ground scar and main wreckage in the background. (item 26, .PDF, 411 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407014&FileExtension=.PDF&FileName=Photo%203.%20View%20of%20ground%20scar%20and%20main%20wreckage%20in%20the%20background.-Master.PDF
- Photo 4. View of the front of the helicopter and main rotor blades. (item 27, .PDF, 443 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407017&FileExtension=.PDF&FileName=Photo%204.%20View%20of%20the%20front%20of%20the%20helicopter%20and%20main%20rotor%20blades.-Master.PDF
- Photo 5. View of main wreckage laying inverted on its right side. (item 28, .PDF, 409 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407019&FileExtension=.PDF&FileName=Photo%205.%20View%20of%20main%20wreckage%20laying%20inverted%20on%20its%20right%20side.%20-Master.PDF
- Photo 6. View of tailboom with main wreckage in background. (item 29, .PDF, 239 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407023&FileExtension=.PDF&FileName=Photo%206.%20View%20of%20tailboom%20with%20main%20wreckage%20in%20background.-Master.PDF
- Photo 7. View of tail rotor, stinger, and tailboom. (item 30, .PDF, 390 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407025&FileExtension=.PDF&FileName=Photo%207.%20View%20of%20tail%20rotor,%20stinger,%20and%20tailboom.-Master.PDF
- Photo 8. View of the bottom side of the helicopter. (item 31, .PDF, 325 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407028&FileExtension=.PDF&FileName=Photo%208.%20View%20of%20the%20bottom%20side%20of%20the%20helicopter.-Master.PDF
- Photo 9. View of the engine and exhaust. (item 32, .PDF, 312 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407029&FileExtension=.PDF&FileName=Photo%209.%20View%20of%20the%20engine%20and%20exhaust.-Master.PDF
- Photo 10. View of cockpit. (item 33, .PDF, 291 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407030&FileExtension=.PDF&FileName=Photo%2010.%20View%20of%20cockpit.-Master.PDF
- Photo 11. View of swashplate and drive links. (item 34, .PDF, 220 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407032&FileExtension=.PDF&FileName=Photo%2011.%20View%20of%20swashplate%20and%20drive%20links.%20-Master.PDF
- Photo 12. View of compressor rotor assembly and fractured 1st-stage compressor blade. (item 35, .PDF, 725 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407035&FileExtension=.PDF&FileName=Photo%2012.%20View%20of%20compressor%20rotor%20assembly%20and%20fractured%201st-stage%20compressor%20blade.%20-Master.PDF
- Photo 13. View of compressor and measurement of outer diameter. (item 36, .PDF, 123 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407036&FileExtension=.PDF&FileName=Photo%2013.%20View%20of%20compressor%20and%20measurement%20of%20outer%20diameter.%20-Master.PDF
- Photo 14.Compressor with bell mouth. (item 37, .PDF, 128 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407037&FileExtension=.PDF&FileName=Photo%2014.Compressor%20with%20bell%20mouth.%20%20-Master.PDF
- Photo 15. C-10D Bell Mouth from N124SH. (item 38, .PDF, 136 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407038&FileExtension=.PDF&FileName=Photo%2015.%20C-10D%20Bell%20Mouth%20from%20N124SH.-Master.PDF
- Photo 16. Bell mouth and the intake plenum. (item 39, .PDF, 129 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407039&FileExtension=.PDF&FileName=Photo%2016.%20Bell%20mouth%20and%20the%20intake%20plenum.-Master.PDF
- Photo 17. Photo of intake plenum. (item 40, .PDF, 134 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407040&FileExtension=.PDF&FileName=Photo%2017.%20Photo%20of%20intake%20plenum.-Master.PDF
- Photo 18. Photo of exemplar compressor, bell mouth, and intake plenum. (item 41, .PDF, 153 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407042&FileExtension=.PDF&FileName=Photo%2018.%20Photo%20of%20exemplar%20compressor,%20bell%20mouth,%20and%20intake%20plenum.%20%20-Master.PDF
- Photo 19. View of air filter still attached to helicopter wreckage. (item 42, .PDF, 288 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407043&FileExtension=.PDF&FileName=Photo%2019.%20View%20of%20air%20filter%20still%20attached%20to%20helicopter%20wreckage.-Master.PDF
- Photo 20. Hobbs Meter (item 43, .PDF, 2.1 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407060&FileExtension=.PDF&FileName=Photo%2020.%20Hobbs%20Meter-Master.PDF
- Photo 21. Engine Data Tag (item 44, .PDF, 991 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40407291&FileExtension=.PDF&FileName=Photo%2021.%20Engine%20Data%20Tag-Master.PDF

From the NTSB's public API. Aircraft are matched to registry aircraft by N-number and event date, checked against the reported serial number, make and model; the registry's history has gaps, so older matches can be wrong. Compare the reported make and model.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.