# NTSB NYC01LA167: Hughes 269A, N7028V, Clay, NY, July 9, 2001 - Type: NTSB accident investigation - Classification: Accident · Minor injuries · Limited investigation · Final report - Date: July 9, 2001, 17:25 local (21:25 UTC) - Place: Clay, NY - Coordinates: 43.180606, -76.170242 (estimated) - Nearby events: https://openairdocs.org/map.md?lat=43.1806&lon=-76.1702&mi=10 - Phase of flight: [Enroute](https://openairdocs.org/ntsb-phases/400) (OpenAirDocs' grouping) - Highest injury: Minor injuries - Injuries: 2 minor - Status: Completed, report January 2, 2002 - Report: Approved by Office Director - Parties: FAA/FSDO - ADs cited in the narratives: [AD 76-18-01](https://openairdocs.org/ad/76-18-01) (OpenAirDocs) - NTSB case key (mKey): 52657 - NTSB case page: https://web.ntsb.gov/investigations/?ntsbnumber=NYC01LA167 - NTSB report (PDF, downloads): https://data.ntsb.gov/carol-repgen/api/Aviation/ReportMain/GenerateNewestReport/52657/pdf - Page: https://openairdocs.org/ntsb/NYC01LA167 ## Probable cause Failure of the left aft cluster fitting due to a fatigue crack. Factors in the accident were the mechanic's failure to identify the crack at the last annual inspection, and the pilot's failure to identify the crack during the last daily inspection ## Sequence of events In NTSB's coding before 2008 (https://www.ntsb.gov/GILS/Documents/codman.pdf). - Airframe/component/system failure/malfunction, cruise - misc rotorcraft,tail boom - fatigue (cause) - maintenance,annual inspection - inadequate, other maintenance personnel (contributing factor) - aircraft preflight - inadequate, pilot in command (contributing factor) ## Analysis The helicopter was in cruise flight when the pilot heard a "bang," and lost tailrotor authority. The pilot maneuvered for landing, and then reduced airspeed in anticipation of landing. The helicopter began to rotate. About 30 to 50 feet agl, the pilot pulled collective to cushion the landing. The helicopter impacted the ground and rolled onto its side. The helicopter received an annual inspection 11 months and 23.3 flight hours prior to the accident. During the annual inspection, the mechanic documented that airworthiness directive (AD) 76-18-01 had been complied with. Examination of the left aft cluster fitting revealed that the tailboom attaching point had separated severing the tailrotor drive shaft. The fracture surfaces for the cluster fitting were relatively flat with smooth curving boundaries, "features typical of fatigue." Most of the relatively rough area in the lower lug had curving arrest lines, "features typical of low-cycle fatigue." AD 76-18-01 stated that within 50 flight hours of the effective date of the AD, and thereafter at intervals not to exceed 50 hours of flight time, or until modifications are accomplished, the tailboom support strut aluminum end fittings were to be visually inspected for deformation or damage, and then checked for cracking using dye penetrant. If cracking or damage was identified the effected structure would have had to been replaced. The AD required the dye penetrant inspection be done in accordance with Service Information Notice N-82.3. In addition, the Service Information Notice stated that a daily visual inspection was required, which the pilot stated he performed prior to the flight. ## Factual narrative On July 9, 2001, about 1725 eastern daylight time, a Hughes 269A, N7028V, was substantially damaged when it rolled over during a precautionary landing near Clay, New York. The certificated commercial pilot and passenger received minor injuries. Visual meteorological conditions prevailed for the personal flight that originated from the Oswego County Airport (FZY), Fulton, New York, destined for the Hancock International Airport (SYR), Syracuse, New York. A flight plan was not filed, and the flight was conducted under 14 CFR Part 91. According to the pilot, he was in cruise flight when he heard a "bang." He then advised Syracuse Air Traffic Control Tower that he was making a precautionary landing. The pilot identified an area, and turned the helicopter 180 degrees to maneuver for his anticipated landing point. During the turn, the pilot looked back at the tailrotor and saw that it was still rotating, but he did not have tailrotor authority. The pilot lowered the collective and started a descent. He then started to reduce the airspeed in anticipation of landing. The helicopter began to rotate, and 30 to 50 feet agl, the pilot pulled collective to cushion the "fall." The helicopter impacted the ground and rolled onto its left side. The pilot and passenger then egressed. According to a Federal Aviation Administration inspector, initial examination of the left tailboom support cluster fitting revealed that the left tailboom attaching point had separated, and the fracture surfaces were dark in color. The tailrotor drive shaft was severed where it entered the aft portion of the fuselage. Both sections of the shaft displayed rotational scoring. According to maintenance records, the helicopter received an annual inspection on July 26, 2000, 23.3 flight hours prior to the accident. During the annual inspection, the mechanic documented that he preformed the requirements of airworthiness directive (AD) 76-18-01 According to a factual report generated by the Safety Board's Materials Laboratory, portions of the fracture surfaces for the cluster fitting lugs were relatively flat with smooth curving boundaries, "features typical of fatigue." Most of the relatively rough area in the lower lug had curving arrest lines, "features typical of low-cycle fatigue." According to AD 76-18-01, within 50 flight hours of the effective date of the AD, and thereafter at intervals not to exceed 50 hours of flight time, or until modifications were accomplished, the cluster fittings were to be visually inspected for deformation or damage, and then checked for cracking using dye penetrant. If cracking or damage was identified, the effected structure would have had to be replaced. The AD also required the dye penetrant inspection be done in accordance with Service Information Notice N-82.3, which stated that the paint be removed from the fitting prior to the inspection. If the fitting was serviceable, a wash coat of zinc chromate primer, and then a coat of epoxy enamel would have had to been applied. In addition, the Service Information Notice stated that a daily visual inspection was required. According to the mechanic, he inspected the cluster fitting in accordance with the AD and the Information Service Notice when he preformed the annual inspection. In addition, the pilot stated that he performed a visual inspection of the aft clevis lugs prior to the first flight of the day, to include the accident flight. ## Aircraft - Registration: [N7028V](https://openairdocs.org/deregistered/N7028V-2004-11-10), registration cancelled 2004-11-10, S/N 760622 (OpenAirDocs) - Reported make and model: Hughes 269A - Registry model: [Hughes 269A](https://openairdocs.org/model/hughes-269a) (registry code 4470402) (OpenAirDocs) - Registry engine: [Lycoming HIO-360 series](https://openairdocs.org/engine/lycoming-hio-360-series) (registry code 41524, reciprocating) (OpenAirDocs) - Category: Helicopter - Serial number: 76-0622 - Airframe hours: 5631.75 - Engines: Lycoming HT-36A 180 horsepower reciprocating - Damage: Substantial damage - Flight: Personal, Part 91 - Registered owner: Mark R. Parker - Airworthiness certificate: Standard, Normal - Last inspection: Annual, July 26, 2000, 23.3 hours before - Departed: FZY, FULTON, NY - Destination: SYR, SYRACUSE, NY ## Flight crew As NTSB recorded them. NTSB leaves out names. - Pilot; age 46; injuries: minor; commercial; airplane ratings: single-engine land; medical: class 2, valid medical--no waivers/lim.; last flight review May 15, 2000; seat: left; flight hours: 14,000 total, 1,700 in this make and model, 13,800 as pilot in command, 250 in the last 90 days, 100 in the last 30 days, 6 in the last 24 hours ## Weather - Conditions: Visual (VMC), Day - Wind: 310° at 10 knots - Visibility: 10 statute miles - Lowest ceiling: none - Temperature: 84 °F, dew point 57 °F - Altimeter: 29.76 inHg - Observed at: SYR, 6 nm away ## FAA reports on this event (1) The FAA's own accident and incident reports, matched to the aircraft by N-number and date (OpenAirDocs). - [Accident 20010709017809A](https://openairdocs.org/incident/20010709017809A), Jul 9, 2001: Hughes 269A, Syracuse, NY, No damage. (-23) On July 9, 2001, at 1725 EST, a Hughes 269A (TH-55), s/n 760622, N7028V, registered to and operated by Mr. Mark r. parker, experienced a crash landing in… ## Other investigations on N7028V (1) From the NTSB's public API. Aircraft are matched to registry aircraft by N-number and event date, checked against the reported serial number, make and model; the registry's history has gaps, so older matches can be wrong. Compare the reported make and model. - [NTSB NYC88LA226](https://openairdocs.org/ntsb/NYC88LA226), Aug 21, 1988: Hughes 269A (N7028V), Pittstown, NJ, substantial damage From the NTSB's public API. Aircraft are matched to registry aircraft by N-number and event date, checked against the reported serial number, make and model; the registry's history has gaps, so older matches can be wrong. Compare the reported make and model. --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.