# NTSB SEA03FA147: Cessna Citation 525, N996JR, Coupeville, WA, July 22, 2003

- Type: NTSB accident investigation
- Classification: Accident · No injuries · Field investigation · Final report
- Date: July 22, 2003, 10:15 local (17:15 UTC)
- Place: Coupeville, WA
- Coordinates: 48.208057, -122.576385
- Nearby events: https://openairdocs.org/map.md?lat=48.2081&lon=-122.5764&mi=10
- Phase of flight: [Enroute](https://openairdocs.org/ntsb-phases/400) (OpenAirDocs' grouping)
- Highest injury: No injuries
- Injuries: 2 uninjured
- Status: Completed, report October 27, 2005
- Report: Approved by Office Director
- Parties: FAA ACO, FAA-FSDO, Cessna Aircraft, NTSB, FAA FSDO
- Safety recommendations: Yes
- ADs cited in the narratives: [AD 2003-21-07](https://openairdocs.org/ad/2003-21-07), AD 2003-23-20, [AD 2004-14-20](https://openairdocs.org/ad/2004-14-20) (OpenAirDocs)
- NTSB case key (mKey): 57547
- NTSB case page: https://web.ntsb.gov/investigations/?ntsbnumber=SEA03FA147
- NTSB report (PDF, downloads): https://data.ntsb.gov/carol-repgen/api/Aviation/ReportMain/GenerateNewestReport/57547/pdf
- NTSB docket: https://data.ntsb.gov/Docket?ProjectID=57547
- Page: https://openairdocs.org/ntsb/SEA03FA147

## Probable cause

The loss of airplane pitch control (trim runway and mistrim condition) resulting from a failure in the airplane's electric pitch trim system.  Factors that contributed to the accident were the manufacturer's inadequate design of the pitch trim circuitry that allowed for a single-point failure mode, and the absence of an adequate failure warning system to clearly alert the pilot to the pitch trim runaway condition in sufficient time to respond in accordance with the manufacturer's checklist instructions.

## Sequence of events

In NTSB's coding before 2008 (https://www.ntsb.gov/GILS/Documents/codman.pdf).

- Airframe/component/system failure/malfunction, climb - to cruise
  - acft/equip,inadequate design, manufacturer (contributing factor)
  - electrical system,electric relay - failure (cause)
- Abrupt maneuver, climb - to cruise
  - flt control syst,elevator trim/tab control - uncommanded (cause)
  - electrical system,electric motor - activated (cause)
- Altitude deviation,uncontrolled, climb - to cruise
- Ditching, emergency landing
  - terrain condition - water

## Analysis

The corporate jet airplane experienced a loss of elevator trim control (runaway trim) that resulted in an uncommanded nose-low pitch attitude. The pilot reported that following the loss of elevator trim authority the airplane was extremely difficult to control and the elevator control forces were extremely high.  The pilot continued to maneuver the airplane, but eventually ditched it into a nearby marine cove.  The runaway trim condition was not immediately recognized by the pilot and he stated that, by that point in the event sequence, the control forces were so great that he had little time to troubleshoot the system and elected to continue on his established heading and ditch the airplane.  Pulling the circuit breaker, which is called for by the checklist in the event of a trim runaway, would have arrested the trim movement.   Post accident examination and functional testing of the airplane's electric pitch trim printed circuit board (PCB) showed a repeatable fault in the operation of the PCB's K6 relay, resulting in the relay contacts remaining closed.  This condition would be representative of the autopilot pitch trim remaining engaged, providing an electrical current to drive continuous nose-down trim to the elevator trim motor.  Examination of the airplane's maintenance records showed that the PCB was removed and replaced in conjunction with the phase inspection prior to the accident.  Further examination of the airplane's maintenance records revealed that the replacement PCB was originally installed in an airplane that experienced an "electric trim runaway on the ground."  Following the trim runaway, the PCB was removed and shipped to the manufacturer.  After receiving the PCB the manufacturer tested the board and no discrepancies were noted.  The unit was subsequently approved for return to service and later installed on the accident airplane.  The investigation revealed a single-point failure of trim runaway (failed K6 relay) and a latent system design anomaly in the autopilot/trim disconnect switch on the airplane's pitch trim PCB.  This design prohibited the disengagement of the electric trim motor during autopilot operation.  As a result of the investigation, the FAA issued three airworthiness directives (AD 2003-21-07, AD 2003-23-20, and AD 2004-14-20), and the pitch trim printed circuit board was redesigned and evaluated for compliance with safety requirements via system safety assessment

## Factual narrative

HISTORY OF FLIGHT

On July 22, 2003, about 1015 Pacific daylight time, a Cessna Citation 525, N996JR, ditched in the waters of Penn Cove, Coupeville, Washington, following a loss of elevator trim control (runaway trim) that resulted in an uncommanded nose-low pitch attitude.  The commercial pilot and passenger were not injured.  Tango Corporation of Minden, Nevada, operated the cross-country flight under the provisions of Title 14, CFR Part 91.   Visual meteorological conditions prevailed for the flight, which was being operated on an instrument flight rules (IFR) flight plan.  The flight originated from the Victoria International Airport (YYJ), Sidney, British Columbia, with a planned destination of Gowen Field (BOI), Boise, Idaho.

At about 0950 the airplane departed Sidney, BC, on an IFR flight plan to Boise, Idaho.  Shortly after clearing Canadian airspace, Victoria Departure Control instructed the pilot to contact Seattle Center (ZSEA).  After establishing communications with ZSEA, the pilot was given a direct clearance to the Boise Airport and instructed to climb to FL330 (flight level 33,000).

After receiving the clearance the pilot turned, via the autopilot, to an on-course heading, reset the altitude pre select to FL330 and set the "…flight director IAS [indicated airspeed] select to 200…" knots.  Shortly after climbing through 14,000 feet mean sea level (MSL), at a climb power setting, the pilot noted a decrease in the aircraft's rate of climb and disconnected the autopilot via the autopilot/trim disconnect switch on the control wheel in an attempt to "hand fly" the aircraft.

Immediately after disconnecting the autopilot, the airplane pitched to a negative deck angle approximately 10 degrees below the horizon.  The pilot reported "Within seconds it was apparent that level flight was not possible as I applied continued back pressure on the yoke."  He reduced engine power to idle, and attempted to electrically re-trim the airplane in an effort to reduce the forward pressure on the control wheel.  He reported the elevator trim indicator was in the full forward (nose down) position and that the electric trim would not respond to inputs via the control wheel trim switch.

The passenger, who was seated in the co-pilot seat, assisted the pilot in applying back pressure to the control wheel.  The pilot reported the negative deck angle had increased and the airspeed was approaching the "barber pole" (maximum operating speed).  He reported that at one point the aircraft's descent rate had reached approximately 2,000 feet per minute and the nose of the airplane was about 40 degrees below the horizon with "…both pilot and passenger exerting maximum yoke back pressure."

The pilot reported that he continued to maneuver the airplane, however the control wheel pressure "…was terrific and required our combined strength to keep the nose from rapidly returning to an extreme angle."  The pilot attempted to re-trim via the manual trim wheel, however the wheel would not move.

The pilot maneuvered the airplane in the direction of Whidbey Island, Washington, in an attempt to reach the Coupeville Naval Outlying Field (KNRA).  After reaching the island, the pilot elected to call off the landing approach at KNRA, and "…chose a straight in approach into a headwind to land on the water at Penn Cove."  Penn Cove was at the pilot's 12 o'clock position at a distance of approximately three miles.

At 1015, the airplane impacted the water approximately 300 yards from the shoreline.  The pilot stated the airplane touched down in a wings level tail low attitude.  The landing gear was in the up position and the flaps were in the landing position (35 degrees).  The pilot estimated that the airplane touched down at 100 knots and traveled less than 50 feet before forward motion ceased.

PERSONNEL INFORMATION

The pilot held a commercial pilot certificate with airplane single-engine land, multi-engine land and instrument airplane ratings.  In addition to the commercial certificate, the pilot held a Cessna Citation 500 type rating, issued in May of 1977 and a Cessna Citation 525 type rating issued in February of 1997.  The pilot completed Cessna Citation recurrent training in September of 2002.

The pilot's most recent FAA third-class medical certificate was issued on October 8, 2001, and contained limitations that the pilot must possess glasses for near and intermediate vision.

According to the Pilot/Operator accident report (Form 6120.1/2), the pilot's total flight time was approximately 8,500 hours, including 8,000 hours as pilot-in-command and 2,689 hours in make and model.  According to the report, the pilot successfully completed a flight review on May 6, 2002.  The review was conducted in a Cessna Citation 525.

The pilot completed initial flight training with the US Army Air Corp in 1943.

AIRCRAFT INFORMATION

The accident airplane, a 1996 Cessna Citation Jet model 525, serial number 525-0147, was manufactured in 1996, and issued a standard airworthiness certificate (normal category) on July 25, 1996.

The airplane was certified in accordance with Federal Aviation Regulation (FAR) Part 23 airworthiness standards, and can be operated by either single or two pilot crews.  A type rating is required to operate the airplane as pilot-in-command.

The airplane was equipped with two Williams International FJ-44-1A medium bypass turbofan engines, rated at 1900 pounds static thrust.

The airplane was delivered new with a Honeywell SPZ-5000 display and flight guidance system.  The system includes, in part, the flight director, electronic attitude director indicator (EADI), electronic horizontal situation indicator (EHSI), altitude alerting system, autopilot, autopilot controller and auto pilot servos.

The primary fight controls are mechanically actuated by cables and have corresponding manual trim control actuators in the cockpit.  The elevator trim control can be actuated manually using a trim wheel located on the center pedestal, or electrically via the electric trim switch on the control wheel or the autopilot pitch wheel.

Airplane maintenance records indicated that the airplane's last inspection, a phase 12 continuous airworthiness inspection, was accomplished on August 29, 2002.

The maintenance records indicated that in conjunction with the phase inspection, the airplane's pitch trim printed circuit board (PCB) assembly (Cessna part number 6518351-5 serial number 0305), was removed "…due to failure and replaced with [a] unit inspected by Cessna Aircraft."  The replacement PCB (serial number 0154) was installed on the accident airplane, operationally checked and returned to service.

The replacement PCB (serial number 0154) was originally installed in N312QS, a Cessna Citation model 560, however after the airplane experienced an "electric trim runaway on the ground" the PC board was removed and replaced.  The removed PC board was subsequently shipped to Cessna Aircraft where it was tested and returned to service.  The Repair Data Report states, in part, "Ran PC board under hot and cold conditions on bench.  No discrepancies noted.  Performed function test and inspection.  Function test and inspection good I/A/W [in accordance with] Cessna Citation Drawing #6518351.  Unit approved for return to service."  The report makes no mention of the type of repairs made to the PC board.  The Cessna Repair Data Report and FAA Form 8130-3  (Airworthiness Approval Tag) are attached.

At the time of the phase inspection, the airframe total time was approximately 508 hours with approximately 302 cycles.  The airplane accrued an additional 82 hours from the time of the inspection to the time of the accident.

METEOROLOGICAL INFORMATION

The 0955 METAR observation at Whidbey Island (KNUW), located approximately 7 miles north of the accident location, reported in part, broken cl

## Aircraft

- Registration: [N996JR](https://openairdocs.org/aircraft/N996JR), registered now, S/N 525-0147, built 1996 (OpenAirDocs)
- Reported make and model: Cessna Citation 525
- Registry model: [Cessna 525](https://openairdocs.org/model/cessna-525) (registry code 2076601) (OpenAirDocs)
- Registry engine: [Williams FJ-44 series](https://openairdocs.org/engine/williams-fj-44-series) (registry code 66000, turbo-fan) (OpenAirDocs)
- Category: Airplane
- Serial number: 0147
- Airframe hours: 590
- Engines: Williams International FJ44-1A 1900 lbs thrust turbo fan; Williams International FJ44-1A 1900 lbs thrust turbo fan
- Damage: Substantial damage
- Flight: Personal, Part 91
- Operator: James C. Ray
- Registered owner: Tango Corporation
- Airworthiness certificate: Standard, Normal
- Last inspection: Continuous airworthiness, August 1, 2002, 82 hours before
- Departed: CYYJ, Sidney
- Destination: BOI, BOISE, ID
- Flight plan: IFR

## Flight crew

As NTSB recorded them. NTSB leaves out names.

- Pilot; age 80; injuries: none; commercial; airplane ratings: multi-engine land, single-engine land; instrument ratings: airplane; medical: class 3, with waivers/limitations; last flight review May 6, 2002; seat: left; flight hours: 8,500 total, 2,689 in this make and model, 8,000 as pilot in command

## Weather

- Conditions: Visual (VMC), Day
- Wind: 290° at 6 knots
- Visibility: 1 statute miles
- Lowest ceiling: 100 ft broken
- Temperature: 55 °F, dew point 54 °F
- Altimeter: 30.12 inHg
- Observed at: KNUW, 7 nm away

## FAA reports on this event (1)

The FAA's own accident and incident reports, matched to the aircraft by N-number and date (OpenAirDocs).

- [Accident 20030722018949A](https://openairdocs.org/incident/20030722018949A), Jul 22, 2003: Cessna 525, Coupeville, WA, Substantial damage. (-23) Enroute from victoria, b.c. to boise, Idaho, a loss of elevator trim control (with an uncommanded 45 degree nose low pitch attitude) occurred while…

## Docket (40 files)

The files NTSB released with the investigation on February 28, 2005, on NTSB's docket system: https://data.ntsb.gov/Docket?ProjectID=57547. 33.5 MB in all.

- Pilot/Operator Aircraft Accident Report, NTSB Form 6120.1 (item 1, .PDF, 420 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391528&FileExtension=.PDF&FileName=Pilot%2FOperator%20Aircraft%20Accident%20Report,%20NTSB%20Form%206120.1-Redacted.PDF
- Group Chairman's Factual Report (Systems) (item 2, .PDF, 368 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226423&FileExtension=.PDF&FileName=Group%20Chairman%27s%20Factual%20Report%20(Systems)-Master.PDF
- Witness/Passenger Statement (item 3, .PDF, 67 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391529&FileExtension=.PDF&FileName=Witness%2FPassenger%20Statement-Redacted.PDF
- Radar Data (item 4, .PDF, 5.6 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226425&FileExtension=.PDF&FileName=Radar%20Data-Master.PDF
- Final Report from Cessna Aircraft Company (Party to Investigation) (item 5, .PDF, 2.6 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391530&FileExtension=.PDF&FileName=Final%20Report%20from%20Cessna%20Aircraft%20Company%20(Party%20to%20Investigation)-Redacted.PDF
- Final Report from Cessna Aircraft Company Photographs (Party to Investigation) (item 6, .PDF, 7.5 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226431&FileExtension=.PDF&FileName=Final%20Report%20from%20Cessna%20Aircraft%20Company%20Photographs%20(Party%20to%20Investigation)-Master.PDF
- Statement of Party Representatives to NTSB Investigation (item 7, .PDF, 50 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391531&FileExtension=.PDF&FileName=Statement%20of%20Party%20Representatives%20to%20NTSB%20Investigation-Redacted.PDF
- Maintenance Records (item 8, .PDF, 7.3 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391533&FileExtension=.PDF&FileName=Maintenance%20Records-Redacted.PDF
- Release of Aircraft Wreckage, NTSB Form 6120.15 (item 9, .PDF, 59 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40391534&FileExtension=.PDF&FileName=Release%20of%20Aircraft%20Wreckage,%20NTSB%20Form%206120.15-Redacted.PDF
- Photo 1: Starboard view of N996JR (Digital Photo) (item 10, .PDF, 270 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226522&FileExtension=.PDF&FileName=Photo%201%3A%20Starboard%20view%20of%20N996JR%20(Digital%20Photo)-Master.PDF
- Photo 2: Portside view of N996JR (Digital Photo) (item 11, .PDF, 254 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226529&FileExtension=.PDF&FileName=Photo%202%3A%20Portside%20view%20of%20N996JR%20(Digital%20Photo)-Master.PDF
- Photo 3: Radar Dome (Digital Photo) (item 12, .PDF, 272 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226534&FileExtension=.PDF&FileName=Photo%203%3A%20Radar%20Dome%20(Digital%20Photo)-Master.PDF
- Photo 4: N996JR on Shipping Barge (Digital Photo) (item 13, .PDF, 266 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226544&FileExtension=.PDF&FileName=Photo%204%3A%20N996JR%20on%20Shipping%20Barge%20(Digital%20Photo)-Master.PDF
- Photo 5: N996JR on Shipping Barge (Digital Photo) (item 14, .PDF, 259 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226547&FileExtension=.PDF&FileName=Photo%205%3A%20N996JR%20on%20Shipping%20Barge%20(Digital%20Photo)-Master.PDF
- Photo 6: Elevator Trim Actuator Measurement (Digital Photo) (item 15, .PDF, 255 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226552&FileExtension=.PDF&FileName=Photo%206%3A%20Elevator%20Trim%20Actuator%20Measurement%20(Digital%20Photo)-Master.PDF
- Photo 7: Circuit Breaker Panel (Digital Photo) (item 16, .PDF, 263 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226554&FileExtension=.PDF&FileName=Photo%207%3A%20Circuit%20Breaker%20Panel%20%20(Digital%20Photo)-Master.PDF
- Photo 8: Circuit Breaker Panel and Pilot Side Yoke (Digital Photo) (item 17, .PDF, 275 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226555&FileExtension=.PDF&FileName=Photo%208%3A%20Circuit%20Breaker%20Panel%20and%20Pilot%20Side%20Yoke%20(Digital%20Photo)-Master.PDF
- Photo 9: Co-pilot Yoke (Digital Photo) (item 18, .PDF, 260 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226558&FileExtension=.PDF&FileName=Photo%209%3A%20Co-pilot%20Yoke%20%20(Digital%20Photo)-Master.PDF
- Photo 10: Pilot Yoke (Digital Photo) (item 19, .PDF, 248 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226559&FileExtension=.PDF&FileName=Photo%2010%3A%20Pilot%20Yoke%20%20(Digital%20Photo)-Master.PDF
- Photo 11: Elevator Trim Wheel and Indicator (Digital Photo) (item 20, .PDF, 251 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226560&FileExtension=.PDF&FileName=Photo%2011%3A%20Elevator%20Trim%20Wheel%20and%20Indicator%20(Digital%20Photo)-Master.PDF
- Photo 12: Elevator Trim Wheel and Indicator (Digital Photo) (item 21, .PDF, 260 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226628&FileExtension=.PDF&FileName=Photo%2012%3A%20Elevator%20Trim%20Wheel%20and%20Indicator%20(Digital%20Photo)-Master.PDF
- Photo 13: Cockpit ((Digital Photo) (item 22, .PDF, 266 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226629&FileExtension=.PDF&FileName=Photo%2013%3A%20Cockpit%20((Digital%20Photo)-Master.PDF
- Photo 14: Control Servos (Digital Photo) (item 23, .PDF, 2.1 MB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226630&FileExtension=.PDF&FileName=Photo%2014%3A%20Control%20Servos%20(Digital%20Photo)-Master.PDF
- Photo 15: "J" Box (Digital Photo) (item 24, .PDF, 251 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226631&FileExtension=.PDF&FileName=Photo%2015%3A%20%22J%22%20Box%20(Digital%20Photo)-Master.PDF
- Photo 16: "J" Box (Digital Photo) (item 25, .PDF, 270 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226633&FileExtension=.PDF&FileName=Photo%2016%3A%20%22J%22%20Box%20(Digital%20Photo)-Master.PDF
- Photo 17: Airworthiness Certificate (Digital Photo) (item 26, .PDF, 268 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226634&FileExtension=.PDF&FileName=Photo%2017%3A%20Airworthiness%20Certificate%20(Digital%20Photo)-Master.PDF
- Photo 18: Hobbs Meter (Digital Photo) (item 27, .PDF, 230 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226635&FileExtension=.PDF&FileName=Photo%2018%3A%20Hobbs%20Meter%20(Digital%20Photo)-Master.PDF
- Photo 19: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 28, .PDF, 268 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226636&FileExtension=.PDF&FileName=Photo%2019%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 20: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 29, .PDF, 304 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226637&FileExtension=.PDF&FileName=Photo%2020%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 21: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 30, .PDF, 284 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226638&FileExtension=.PDF&FileName=Photo%2021%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 22: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 31, .PDF, 242 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226639&FileExtension=.PDF&FileName=Photo%2022%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 23: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 32, .PDF, 270 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226640&FileExtension=.PDF&FileName=Photo%2023%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 24: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 33, .PDF, 268 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226641&FileExtension=.PDF&FileName=Photo%2024%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 25: Trim Relay Printed Circuit Board (PCB) (Digital Photo) (item 34, .PDF, 260 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226642&FileExtension=.PDF&FileName=Photo%2025%3A%20Trim%20Relay%20Printed%20Circuit%20Board%20(PCB)%20(Digital%20Photo)-Master.PDF
- Photo 26: Trim Tab (Digital Photo) (item 35, .PDF, 254 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226643&FileExtension=.PDF&FileName=Photo%2026%3A%20Trim%20Tab%20(Digital%20Photo)-Master.PDF
- Photo 27: Trim Indicators (Rudder & Aileron) (Digital Photo) (item 36, .PDF, 271 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226645&FileExtension=.PDF&FileName=Photo%2027%3A%20Trim%20Indicators%20(Rudder%20%26%20Aileron)%20%20(Digital%20Photo)-Master.PDF
- Photo 28: Trim Motor (Digital Photo) (item 37, .PDF, 265 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226646&FileExtension=.PDF&FileName=Photo%2028%3A%20Trim%20Motor%20(Digital%20Photo)-Master.PDF
- Photo 29: Trim Cables (Digital Photo) (item 38, .PDF, 264 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40226647&FileExtension=.PDF&FileName=Photo%2029%3A%20Trim%20Cables%20(Digital%20Photo)-Master.PDF
- Photo 30: N996JR prior to ditching (item 39, .PDF, 80 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40392007&FileExtension=.PDF&FileName=Photo%2030%3A%20N996JR%20prior%20to%20ditching-Master.PDF
- Photo 31: N996JR prior to ditching (item 40, .PDF, 90 KB): https://data.ntsb.gov/Docket/Document/docBLOB?ID=40392008&FileExtension=.PDF&FileName=Photo%2031%3A%20N996JR%20prior%20to%20ditching-Master.PDF

From the NTSB's public API. Aircraft are matched to registry aircraft by N-number and event date, checked against the reported serial number, make and model; the registry's history has gaps, so older matches can be wrong. Compare the reported make and model.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.
