# Airbus Canada Service Bulletin BD500-501003: Revision 003

- Rights: © Airbus Canada Limited Partnership. Filed by the FAA in regulations.gov docket FAA-2025-0199, the docket of AD 2026-10-10. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Airbus Canada Service Bulletin BD500-501003](https://openairdocs.org/service-documents/airbus-canada/bd500-501003.md)
- Title as filed: BD500-501003_Issue003
- Pages: 104
- PDF: https://openairdocs.org/files/sha256/5d/00/5d00a96e0659e92eb35ecb2d367168c1431c37e5e5cc95c9e37d8dd28094fe23
- Page: https://openairdocs.org/service-documents/airbus-canada/bd500-501003/file/5d00a96e0659

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

BD500-501003
 
Cargo and Accessory Compartment - Cargo
Compartments - Installation of Sleeve on the
Environmental Control System Ducts - Service
Bulletin
BD500-501003
Issue No. 003.00
Copyright © Airbus Canada Limited Partnership
All rights reserved. No part of this work may be reproduced or copied in any form or by any means without written permission of Airbus
Canada Limited Partnership.
The Airbus and A220 logos are registered trademarks of Airbus Canada Limited Partnership.
The information, technical data and the designs disclosed herein are the exclusive property of Airbus Canada Limited Partnership or contain
proprietary rights of others and are not to be used or disclosed to others without the written consent of Airbus Canada Limited Partnership. The
recipient of this document, by its retention and use, agrees to hold in confidence the technical data and designs contained herein. The foregoing
shall not apply to persons having proprietary rights to such information, technical data or such designs to the extent that such rights exist.
Publication No.:
Manufacturer:
Airbus Canada Limited Partnership
Customer Services
13100 Henri-Fabre Blvd.
Mirabel, Quebec J7H 3C6
  Page  1
2024/12/18
Original issue date: --2023-12-21

### Page 2

Intentionally left blank
  Page  2
2024/12/18
Original issue date: --2023-12-21

### Page 3

BD500-501003
Cargo and Accessory Compartment - Cargo Compartments - Installation
of Sleeve on the Environmental Control System Ducts - Service Bulletin
References
Table 1 References
Data Module/Technical Publication Title
BD500-A-J50-10-03-01AAA-933A-A PART A - Installation of Sleeve on the Environmental
Control System Ducts - Accomplishment instruction
BD500-A-J50-10-03-01AAA-934A-A Installation of Sleeve on the Environmental Control
System Ducts - Material information
BD500-A-J50-10-03-02AAA-910B-A APPENDIX A - Miscellaneous
BD500-A-J50-10-03-02AAA-933A-A PART B - Identification of the Ceiling Panel liners in
the Cargo Compartments - Accomplishment instruction
Service Bulletin
Common information
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS
LEASED AIRCRAFT, SEND THE SERVICE BULLETIN TO THE LESSEE. IF THE OPERATOR
HAS SOLD AIRCRAFT OR TRANSFERRED SPARES IN THE LAST SIX MONTHS, SEND
THIS SERVICE BULLETIN TO THE NEW OWNER, UNLESS CONFIRMATION WAS
RECEIVED THAT AIRBUS HAS INCLUDED THE NEW OPERATOR ON THE DISTRIBUTION
LIST.
Management information
Compliance category: Mandatory (Service bulletin must be accomplished)
Task category: Inspection and repair
Original issue date: 2023-12-21
Impact list
Impact (Maintenance publications):
Refer to the Documentation affected section of the Planning Information section.
Accomplishment limits
Time compliance: Basic limit
Remarks:
Refer to the Compliance section of the Planning Information section.
Replacement service bulletin
None
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
 2024-12-18 Page  3
Original issue date: --2023-12-21

### Page 4

BD500-501003
Revision information
Revision information
The revision information letter transmits:
Issue 003 of Service Bulletin BD500-501003, dated 2024-12-18.
Additional work
For Aircraft that have incorporated issue 001 of this service bulletin, it is necessary to do
PART B to identify the cargo compartment ceiling panel liners and report the result.
Revision reason
Revised the Planning information to:
Change the Compliance section to Mandatory.
Change the revision of some referenced documents.
Revision history
Issue 001, dated 2023-12-21
Issue 002, dated 2024-11-15
Revision sequence
Discard the copy of Service Bulletin BD500-501003, Issue 002, dated 2024-11-15. Replace with
the copy attached.
Summary
Applicability
BD-500-1A10, Aircraft 50060, 50062, and 50063
BD-500-1A11, Aircraft 55128 thru 55150, 55152, 55154, and 55155
Reason
It is possible that some Environmental Control System (ECS) ducts do not comply with the
flammability requirements.
Description
This service bulletin is divided into two parts: PART A and PART B
PART A - Installation of Sleeve on the Environmental Control System Ducts
The aircraft is put in standard configuration for maintenance. The Forward Cargo Compartment
Door (FCCD) and Aft Cargo Compartment Door (ACCD) are opened. Some cargo compartment
sidewalls are removed. The lot numbers are examined on four ECS ducts and recorded in
the APPENDIX A. If necessary, the cargo compartment ceiling panels are removed and the
Safran Cabin Service Bulletin F493000-50-06 is done. Ceiling panels are identified. If they
were removed, the cargo compartment ceiling panels are installed. Some cargo compartment
sidewalls are installed. The FCCD and ACCD are closed.
PART B - Identification of the Ceiling Panel liners in the Cargo Compartments
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
 2024-12-18 Page  4
Original issue date: --2023-12-21

### Page 5

BD500-501003
The aircraft is put in standard configuration for maintenance. The FCCD and ACCD are
opened. Some cargo compartment sidewalls are removed. The lot numbers are examined on
four ECS ducts and recorded in the APPENDIX A. Ceiling panels are identified. Some cargo
compartment sidewalls are installed. The FCCD and ACCD are closed.
Concurrent requirements
None
Manpower
It will take an estimated 12.00 h to complete PART A of this service bulletin.
Note
This estimate does not include the man-hours necessary to do Safran Cabin Service
Bulletin F493000-50-06.
It will take an estimated 6.00 h to complete PART B of this service bulletin.
Material information
BD500-A-J50-10-03-01AAA-934A-A
Planning information
Applicability
Aircraft affected:
AIRCRAFT MODEL SERVICE AIRCRAFT SERIAL
NUMBER
PRODUCTION AIRCRAFT
SERIAL NUMBERS
BD-500-1A10 50060, 50062, and 50063 50067 and subsequent serial
numbers 1
BD-500-1A11 55128 thru 55150, 55152,
55154, and 55155
55160, 55164 and subsequent
serial numbers1
1 Aircraft will have an equivalent modification incorporated before delivery.
Note
The instructions in this service bulletin are only applicable to the systems and parts
installed at the time of delivery of the aircraft or as changed by Airbus Service Bulletins.
Before you do this service bulletin, examine all Supplemental Type Certificates (STCs),
Supplemental Type Approvals (STAs), or equivalent action changes to make sure that you
can complete this service bulletin.
Reason
Problem and effect
It is possible that some ECS ducts do not comply with the flammability requirements.
Objective/Solution
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
 2024-12-18 Page  5
Original issue date: --2023-12-21

### Page 6

BD500-501003
This service bulletin gives the procedure to examine the lot numbers on four ECS ducts, record
the lot numbers in the APPENDIX A, and if necessary, do the Safran Cabin Service Bulletin
F493000-50-06 to add a sleeve to the ECS ducts to obey the flammability requirements.
Description
This service bulletin is divided into two parts: PART A and PART B
PART A - Installation of Sleeve on the Environmental Control System Ducts
The aircraft is put in standard configuration for maintenance. The FCCD and ACCD are
opened. Some cargo compartment sidewalls are removed. The lot numbers are examined on
four ECS ducts and recorded in the APPENDIX A. If necessary, the cargo compartment ceiling
panels are removed and the Safran Cabin Service Bulletin F493000-50-06 is done. Ceiling
panels are identified. If they were removed, the cargo compartment ceiling panels are installed.
Some cargo compartment sidewalls are installed. The FCCD and ACCD are closed.
PART B - Identification of the Ceiling Panel liners in the Cargo Compartments
The aircraft is put in standard configuration for maintenance. The FCCD and ACCD are
opened. Some cargo compartment sidewalls are removed. The lot numbers are examined on
four ECS ducts and recorded in the APPENDIX A. Ceiling panels are identified. Some cargo
compartment sidewalls are installed. The FCCD and ACCD are closed.
Compliance
Mandatory Service Bulletin
Airbus recommends that PART A and/or PART B of this service bulletin be done before
the aircraft has 9350 flight hours or no later than 60 months from the release date of the
initial issue on this service bulletin, whichever comes first, unless otherwise directed by the
airworthiness authority of the operator.
Note
If it is not possible to complete all the instructions in this service bulletin because of
the configuration of the aircraft, speak with a CRC representative at 1 866 A220 CRC
(1-866-222-0272) or 1-450-476-7676 or e-mail at a220crc@airbus.com for analysis and to
get an approved disposition to complete this service bulletin.
Note
This service bulletin does not affect Airworthiness Limitations Items (ALIs) or Damage
Tolerance Inspections (DTIs).
Concurrent requirements
None
Approval
The technical content of this service bulletin has been approved under the authority of the
TCCA Design Approval Organization No: DAO #19-Q-02.
Manpower
The man-hours given below are estimates for direct labor done by an experienced crew on an
aircraft prepared for maintenance.
These estimates do not include the time necessary for:
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
 2024-12-18 Page  6
Original issue date: --2023-12-21

### Page 7

BD500-501003
‐ Administrative functions such as planning, liaising, familiarization, and report writing.
‐ Non-productive elapsed time such as rest time, having meals, and crew shift changes.
‐ Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
‐ Preparation for modification (unless specified in the Accomplishment Instructions) such as
cleaning and getting parts, tools, consumables, and ground equipment.
‐ Quality assurance inspections, troubleshooting and/or correction of discrepancies found
when a task is done.
‐ All other activities that are not considered by Airbus as directly related to the
accomplishment of this procedure.
It will take an estimated 12.00 h to complete PART A of this service bulletin. The man-hours
are divided as shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 2.00 h
Procedure 7.00 h
Test 1.00 h
Job Close-Up 2.00 h
Note
These estimates do not include the man-hours necessary to do Safran Cabin Service
Bulletin F493000-50-06.
It will take an estimated 6.00 h to complete PART B of this service bulletin. The man-hours
are divided as shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 2.00 h
Procedure 2.00 h
Test 0.00 h
Job Close-Up 2.00 h
Weight and balance
Not changed
Electrical load data
Not changed
Referenced documentation
Refer to the SB Introduction document BD500-000000 for definition or explanation of service
bulletin content.
Modification Summary 500T105050, Revision B
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
 2024-12-18 Page  7
Original issue date: --2023-12-21

### Page 8

BD500-501003
For Airbus reference only: Restriction and/or Special Instruction (RSI) C-500-000-50-0004,
Revision C
Safran Cabin Service Bulletin F493000-50-06, Revision 1, dated Oct 31/24
For Airbus reference only: PCR 60543
Documentation affected
1 Maintenance Publications
Aircraft Maintenance Publication (AMP)
Illustrated Parts Data Publication (IPDP)
2 Operational Publications
None
Industry support information
This service bulletin is part of an AIRBUS monitored retrofit campaign. For detailed information,
please refer to Retrofit Information Letter (RIL) S25M23001960. To organize this retrofit, please
contact AIRBUS retrofit management department at: a220monitored.retrofit@airbus.com.
Material information
BD500-A-J50-10-03-01AAA-934A-A
Accomplishment instructions
For PART A BD500-A-J50-10-03-01AAA-933A-A
For PART B BD500-A-J50-10-03-02AAA-933A-A
Additional information
Additional information
APPENDIX A BD500-A-J50-10-03-02AAA-910B-A
See applicability on the first page of the DM
BD500-A-J50-10-03-00AAA-930A-A (003)
BD500-A-J50-10-03-00AAA-930A-A (003)
End of data module
 2024-12-18 Page  8
Original issue date: --2023-12-21

### Page 9

BD500-501003
Installation of Sleeve on the Environmental
Control System Ducts - Material information
References
Table 1 References
Data Module/Technical Publication Title
BD500-A-J51-31-00-01AAA-070A-A Supply requirements - Consumables and materials
Service Bulletin
Material set list
None
Support equipment list
There is no support equipment for this service bulletin.
Supplies list
For a list of supplies, refer to the different tasks and the Safran Cabin Service Bulletin that are
given as references in this service bulletin.
Spares list
The spare that follows is available from Satair:
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
Individual spare:
◂
Part number
[Mfg. code]
Name Quantity Remarks
B0816123-7-0
[3AB48]
Strap, Tiedown 4
The spare sets in the table that follows are available from Satair:
Applicability: 50060, 50062-50063
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-934A-A (003)
BD500-A-J50-10-03-01AAA-934A-A (003)
 2024-12-18 Page  9
Original issue date: --2023-12-21

### Page 10

BD500-501003
▸
Spare set: Kit BD500501003K350
◂
Name: ECS Duct Improvement A220-100 Kit
Part number
[Mfg. code]
Name Quantity Remarks
CDKF49-3-53
[56135]
ECS Duct Improvement-
A220-100
1
Procurement information:
Price information: $4840.00
Availability: 111 days (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained thru
Satair Customer Order Specialist: Americas: spares.americas@satair.com, Asia:
spares.aspac@satair.com Europe and Africa: spares.emea@satair.com.
Applicability: 55128-55150, 55152, 55154-55155
▸
Spare set: Kit BD500501003K351
◂
Name: ECS Duct Improvement A220-300 Kit
Part number
[Mfg. code]
Name Quantity Remarks
CDKF49-3-54
[56135]
ECS Duct Improvement-
A220-300
1
Procurement information:
Price information: $4840.00
Availability: 111 days (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained thru
Satair Customer Order Specialist: Americas: spares.americas@satair.com, Asia:
spares.aspac@satair.com Europe and Africa: spares.emea@satair.com.
Procurement address:
Name: For customers based in the Americas
Business unit:
Business unit name: Satair USA, Inc
525 Westpark Drive, Suite 400
Peachtree City, GA  30269
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-934A-A (003)
BD500-A-J50-10-03-01AAA-934A-A (003)
 2024-12-18 Page  10
Original issue date: --2023-12-21

### Page 11

BD500-501003
United States of America
Ph.: 1 404 675 6333
Please contact your Customer Order Specialist
https:/www.satair.com/market/search
CPHSB7X
Name: For customers based in Europe, Middle East, Africa
Business unit:
Business unit name: Satair A/S
Amager Landevej 147A
2770 Kastrup
Denmark
Ph.: 45 3247 0100
Please contact your Customer Order Specialist
https:/www.satair.com/market/search
CPHSB7X
Name: For customers based in the Asia Pacific (excluding mainland China)
Business unit:
Business unit name: Satair Pte Ltd
12 Seletar Aerospace Link
Singapore  797553
The Republic of Singapore
Ph.: 65 6543 0977
Please contact your Customer Order Specialist
https:/www.satair.com/market/search
CPHSB7X
Name: For customers based in mainland China
Business unit:
Business unit name: Satair (Beijing) Co. Ltd
Tian Zhu Lu 8, Tianzhu Airport Industrial Zone
Beijing  101312
People’s Republic of China
Ph.: 86 10 8048 6161
Please contact your Customer Order Specialist
https:/www.satair.com/market/search
CPHSB7X
Removed spares list
Individual removed spare:
Pre-SB
Part number
[Mfg. code]
Name Qty Usage Post-SB
Part number
[Mfg. code]
Description
(Repl. condition)
[Repl. code]
D761105-121
[56135]
Ceiling Assembly,
FWD
1 Modified to KC25060543001-101
or
KC25060543001-201
[56135]
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-934A-A (003)
BD500-A-J50-10-03-01AAA-934A-A (003)
 2024-12-18 Page  11
Original issue date: --2023-12-21

### Page 12

BD500-501003
Individual removed spare:
Pre-SB
Part number
[Mfg. code]
Name Qty Usage Post-SB
Part number
[Mfg. code]
Description
(Repl. condition)
[Repl. code]
D761103-113
[56135]
Ceiling Assembly,
FWD
1 Modified to KC25060543001-103
or
KC25060543001-203
[56135]
Individual removed spare:
Pre-SB
Part number
[Mfg. code]
Name Qty Usage Post-SB
Part number
[Mfg. code]
Description
(Repl. condition)
[Repl. code]
D761104-109
[56135]
Ceiling Assembly,
FWD
1 Modified to KC25060543001-105
or
KC25060543001-205
[56135]
Individual removed spare:
Pre-SB
Part number
[Mfg. code]
Name Qty Usage Post-SB
Part number
[Mfg. code]
Description
(Repl. condition)
[Repl. code]
D765101-113
[56135]
Ceiling Assembly,
FWD
1 Modified to KC25060543001-113
or
KC25060543001-213
[56135]
Individual removed spare:
Pre-SB
Part number
[Mfg. code]
Name Qty Usage Post-SB
Part number
[Mfg. code]
Description
(Repl. condition)
[Repl. code]
D761134-111
[56135]
Ceiling Assembly,
Aft
1 Modified to KC25060543001-107
or
KC25060543001-207
[56135]
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-934A-A (003)
BD500-A-J50-10-03-01AAA-934A-A (003)
End of data module
 2024-12-18 Page  12
Original issue date: --2023-12-21

### Page 13

BD500-501003
PART A - Installation of Sleeve on the Environmental
Control System Ducts - Accomplishment instruction
References
Table 1 References
Data Module/Technical Publication Title
BD500-A-J12-00-00-01AAA-398A-A Standard configuration for maintenance - Aircraft system
configuration
BD500-A-J20-60-01-02AAA-913A-A Identification of aircraft parts and assemblies - General
maintenance procedure
BD500-A-J50-10-03-01AAA-910B-A Safran Cabin Service Bulletin - F493000-50-06
BD500-A-J50-10-03-02AAA-910B-A APPENDIX A - Miscellaneous
BD500-A-J50-11-01-01AAA-520A-A Forward cargo compartment sidewall panel liner -
Remove procedure
BD500-A-J50-11-01-01AAA-720A-A Forward cargo compartment sidewall panel liner - Install
procedure
BD500-A-J50-11-03-01AAA-520A-A Forward cargo compartment ceiling panel liner -
Remove procedure
BD500-A-J50-11-03-01AAA-720A-A Forward cargo compartment ceiling panel liner - Install
procedure
BD500-A-J50-12-01-01AAA-520A-A Aft cargo compartment sidewall panel - Remove
procedure
BD500-A-J50-12-01-01AAA-720A-A Aft cargo compartment sidewall panel - Install
procedure
BD500-A-J50-12-03-01AAA-520A-A Aft cargo compartment ceiling panel liner - Remove
procedure
BD500-A-J50-12-03-01AAA-720A-A Aft cargo compartment ceiling panel liner - Install
procedure
BD500-A-J52-30-00-01AAA-540A-A Cargo compartment door - Open for access procedure
BD500-A-J52-30-00-01AAA-740A-A Cargo compartment door - Close after access
procedure
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  13
Original issue date: --2023-12-21

### Page 14

BD500-501003
Preliminary requirements
Required conditions
Table 2  Required conditions
Action/Condition Data Module/Technical publication
None
Support equipment
Table 3  Support equipment
Name Identification/Reference Quantity Remark
None
Consumables, materials, and expendables
Table 4  Consumables, materials, and expendables
Name Identification/Reference Quantity Remark
None
Spares
Table 5  Spares
Name Identification/Reference Quantity Remark
None
Safety conditions
None
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  14
Original issue date: --2023-12-21

### Page 15

BD500-501003
Procedure
1 General information
Note
This service bulletin is classified as Mandatory or expected to be Mandatory by
an Airworthiness Directive (AD). The Procedure section of the Accomplishment
Instructions is Required for Compliance (RC) and must be done to comply with
the AD. The Job set-up and Job close-up sections, with the exception of the
return-to-service tests, are recommended and can be deviated from, done as part
of other actions, or done with accepted methods different from those given in the
service bulletin, as long as the RC section can be done and the aircraft can be
put back into a serviceable condition.
2 Job set-up
Note
The steps in the Job set-up section of this service bulletin are recommended
steps. The steps give a recommendation to get access to the work area. This
recommendation is to give a safe work area and to minimize possible damage to
surrounding aircraft parts. Alternative steps can be used at the discretion of the
operator.
2.1 Make sure that the aircraft is in standard configuration for maintenance (refer to
AMP BD500-A-J12-00-00-01AAA-398A-A).
2.2 Open the Forward Cargo Compartment Door (FCCD) and the Aft Cargo
Compartment Door (ACCD) (refer to AMP BD500-A-J52-30-00-01AAA-540A-A).
Applicability: 50060, 50062-50063
▸
2.3 Remove the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124HRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
144BRW Aft cargo compartment door
surround panel
AMP BD500-A-
J50-12-01-01AAA-520A-A
◂
Applicability: 55128-55150, 55152, 55154-55155
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  15
Original issue date: --2023-12-21

### Page 16

BD500-501003
▸
2.4 Remove the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124KRW Forward cargo compartment
panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
144BRW Aft cargo compartment door
surround panel
AMP BD500-A-
J50-12-01-01AAA-520A-A
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3 Procedure
3.1 If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a CRC representative
at 1 866 A220 CRC (1-866-222-0272) or 1-450-476-7676 or e-mail at
a220crc@airbus.com for analysis and to get an approved disposition to complete
this service bulletin.
3.2 Read the maintenance records of the aircraft to see if the part numbers that
follow have been relocated:
‐ Ceiling panel D761105-121 (123ALC)
‐ Ceiling panel D761103-113 (123GLC)
‐ Ceiling panel D761104-109 (123HLC)
‐ Ceiling panel D765101-113 (123MLC)
‐ Ceiling panel D761134-111 (143ALC)
‐ Environmental Control System (ECS) duct D761189-501
‐ ECS duct D762232-509
‐ ECS duct D761189-105
If some of the ECS ducts and/or ceiling panels (from aircraft 50060, 50062,
50063, 55128 thru 55150, 55152, 55154, and 55155) were relocated to
another aircraft that is not within the effectivity of this Service Bulletin, find on
which aircraft the ECS duct(s) and/or ceiling panel(s) are installed. Use the
interchangeability code to replace the ECS duct(s) and/or ceiling panels(s) with
the production assembly with sleeve: D761103-113-N0004, D761104-109-N0002,
D761105-121-N0004, D761134-111-N0004, D765101-113-N0004.
3.3 Examine the lot number on the ECS ducts (1), (2), (3), and (4).
Refer to Table 6 and Fig. 1
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  16
Original issue date: --2023-12-21

### Page 17

BD500-501003
Table 6 Environmental Control System (ECS) duct lot numbers
2105007133 2111001033 2107003544 2109034337
2105041052 2111001500 2109033947 2109034339
2107002212 2111001501 2109044372 2109044437
2107002352 2111038321 2109044374 2109044438
2107002763 2104048786 2110003776 2110028055
2107003043 2104048788 2110014032 2110028056
2107003611 2106005997 2110014033 2111000889
2109044474 2107002940 2104018055 2111000890
2109044476 2109044487 2104048950 2111001392
2110003613 2105042217 2105007075 2111001394
2110036846 2107002269 2107002303 2111038316
2110036848 2107002316 2107003273 2111038318
2111001032 2107003542 2107003275
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.4 For an ECS duct (1) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.4.1 Remove the ceiling panel 123ALC (refer to AMP BD500-A-
J50-11-03-01AAA-520A-A).
3.4.2 Record the lot number of the ECS duct (1) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.4.3 Do the applicable sections of the Safran Cabin Service Bulletin
F493000-50-06 (refer to BD500-A-J50-10-03-01AAA-910B-A).
3.4.4 With indelible ink or equivalent, identify the ceiling panel D761105-121
(123ALC) as KC25060543001-101 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
3.4.5 Install the ceiling panel 123ALC (refer to AMP BD500-A-
J50-11-03-01AAA-720A-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  17
Original issue date: --2023-12-21

### Page 18

BD500-501003
▸
3.5 For an ECS duct (1) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761105- 121 (123ALC)
as KC25060543001-201 and record the lot number of the ECS duct (1) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.6 For an ECS duct (2) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.6.1 Remove the ceiling panel 123GLC (refer to AMP BD500-A-
J50-11-03-01AAA-520A-A).
3.6.2 Record the lot number of the ECS duct (2) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.6.3 Do the applicable sections of the Safran Cabin Service Bulletin
F493000-50-06 (refer to BD500-A-J50-10-03-01AAA-910B-A).
3.6.4 With indelible ink or equivalent, identify the ceiling panel D761103-113
(123GLC) as KC25060543001-103 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
3.6.5 Install the ceiling panel 123GLC (refer to AMP BD500-A-
J50-11-03-01AAA-720A-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.7 For an ECS duct (2) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761103-113 (123GLC)
as KC25060543001-203 and record the lot number of the ECS duct (2) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063
▸
3.8 For an ECS duct (3) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.8.1 Remove the ceiling panel 123HLC (refer to AMP BD500-A-
J50-11-03-01AAA-520A-A).
3.8.2 Record the lot number of the ECS duct (3) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  18
Original issue date: --2023-12-21

### Page 19

BD500-501003
3.8.3 Do the applicable sections of the Safran Cabin Service Bulletin
F493000-50-06 (refer to BD500-A-J50-10-03-01AAA-910B-A).
3.8.4 With indelible ink or equivalent, identify the ceiling panel D761104-109
(123HLC) as KC25060543001-105 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
3.8.5 Install the ceiling panel 123HLC (refer to AMP BD500-A-
J50-11-03-01AAA-720A-A).
◂
Applicability: 50060, 50062-50063
▸
3.9 For an ECS duct (3) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761104-109 (123HLC)
as KC25060543001-205 and record the lot number of the ECS duct (3) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
3.10 For an ECS duct (3) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.10.1 Remove the ceiling panel 123MLC (refer to AMP BD500-A-
J50-11-03-01AAA-520A-A).
3.10.2 Record the lot number of the ECS duct (3) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.10.3 Do the applicable sections of the Safran Cabin Service Bulletin
F493000-50-06 (refer to BD500-A-J50-10-03-01AAA-910B-A).
3.10.4 With indelible ink or equivalent, identify the ceiling panel D765101-113
(123MLC) as KC25060543001-113 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
3.10.5 Install the ceiling panel 123MLC (refer to AMP BD500-A-
J50-11-03-01AAA-720A-A).
◂
Applicability: 55128-55150, 55152, 55154-55155
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  19
Original issue date: --2023-12-21

### Page 20

BD500-501003
▸
3.11 For an ECS duct (3) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D765101-113 (123MLC)
as KC25060543001-213 and record the lot number of the ECS duct (3) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.12 For an ECS duct (4) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.12.1 Remove the ceiling panel 143ALC (refer to AMP BD500-A-
J50-12-03-01AAA-520A-A).
3.12.2 Record the lot number of the ECS duct (4) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.12.3 Do the applicable sections of the Safran Cabin Service Bulletin
F493000-50-06 (refer to BD500-A-J50-10-03-01AAA-910B-A).
3.12.4 With indelible ink or equivalent, identify the ceiling panel D761134-111
(143ALC) as KC25060543001-107 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
3.12.5 Install the ceiling panel 143ALC (refer to AMP BD500-A-
J50-12-03-01AAA-720A-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.13 For an ECS duct (4) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761134-111 (143ALC)
as KC25060543001-207 and record the lot number of the ECS duct (4) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  20
Original issue date: --2023-12-21

### Page 21

BD500-501003
Applicability: 50060, 50062-50063
LEGEND
1. ECS duct
2. ECS duct
3. ECS duct
4. ECS duct
1
2
3
4
FS475.6
(REF)
FS995.47
(REF)
FS1261.95
(REF)
FS668.5
(REF)
A220-100
ITEM CP1209543
P/N D761189-501
DESC ECS DUCT
REV. NCLOT 2203004495
TYPICAL
ICN-BD500-A-J501003-F-3AB48-95301-A-001-01
Fig. 1 Environmental Control System (ECS) ducts
- (Sheet 1 of 2)
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  21
Original issue date: --2023-12-21

### Page 22

BD500-501003
Applicability: 55128-55150, 55152, 55154-55155
LEGEND
1. ECS duct
2. ECS duct
3. ECS duct
4. ECS duct
1
2
3
4
FS391.6
(REF)
FS668.5
(REF)
FS995.47
(REF)
FS1324.95
(REF)
A220-300
ITEM CP1209543
P/N D761189-501
DESC ECS DUCT
REV. NCLOT 2203004495
TYPICAL
ICN-BD500-A-J501003-F-3AB48-95302-A-001-01
Fig. 1 Environmental Control System (ECS) ducts
- (Sheet 2 of 2)
◂
◂
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  22
Original issue date: --2023-12-21

### Page 23

BD500-501003
4 Job close-up
Note
The steps in the Job close-up section of this service bulletin, except for the
return-to-service tests, are recommended steps. The steps give a recommendation
to install components removed during the Job set-up. This recommendation is
to make sure that the aircraft is safe and ready to return to service. Alternative
steps can be used at the discretion of the operator.
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
4.1 Remove all tools, equipment, and unwanted materials from the work area.
◂
Applicability: 50060, 50062-50063
▸
4.2 Install the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124HRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
144BRW Aft cargo door surround panel AMP BD500-A-
J50-12-01-01AAA-720A-A
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
4.3 Install the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124KRW Forward cargo compartment
panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
 2024-12-18 Page  23
Original issue date: --2023-12-21

### Page 24

BD500-501003
PANEL NAME REFERENCE
144BRW Aft cargo door surround panel AMP BD500-A-
J50-12-01-01AAA-720A-A
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
4.4 Close the FCCD and the ACCD (refer to AMP BD500-A-J52-30-00-01AAA-740A-
A).
◂
4.5 Send APPENDIX A to the CRC at A220_crc@abc.airbus for analysis.
5 Administrative
When PART A of this service bulletin is completed, record in the applicable aircraft
records that you have completed PART A of this service bulletin.
Requirements after job completion
Required conditions
Table 7  Required conditions
Action/Condition Data Module/Technical publication
None
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-933A-A (003)
BD500-A-J50-10-03-01AAA-933A-A (003)
End of data module
 2024-12-18 Page  24
Original issue date: --2023-12-21

### Page 25

BD500-501003
PART B - Identification of the Ceiling Panel liners in
the Cargo Compartments - Accomplishment instruction
References
Table 1 References
Data Module/Technical Publication Title
BD500-A-J12-00-00-01AAA-398A-A Standard configuration for maintenance - Aircraft system
configuration
BD500-A-J20-60-01-02AAA-913A-A Identification of aircraft parts and assemblies - General
maintenance procedure
BD500-A-J50-10-03-02AAA-910B-A APPENDIX A - Miscellaneous
BD500-A-J50-11-01-01AAA-520A-A Forward cargo compartment sidewall panel liner -
Remove procedure
BD500-A-J50-11-01-01AAA-720A-A Forward cargo compartment sidewall panel liner - Install
procedure
BD500-A-J50-12-01-01AAA-520A-A Aft cargo compartment sidewall panel - Remove
procedure
BD500-A-J50-12-01-01AAA-720A-A Aft cargo compartment sidewall panel - Install
procedure
BD500-A-J52-30-00-01AAA-540A-A Cargo compartment door - Open for access procedure
BD500-A-J52-30-00-01AAA-740A-A Cargo compartment door - Close after access
procedure
Preliminary requirements
Required conditions
Table 2  Required conditions
Action/Condition Data Module/Technical publication
None
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  25
Original issue date: --2023-12-21

### Page 26

BD500-501003
Support equipment
Table 3  Support equipment
Name Identification/Reference Quantity Remark
None
Consumables, materials, and expendables
Table 4  Consumables, materials, and expendables
Name Identification/Reference Quantity Remark
None
Spares
Table 5  Spares
Name Identification/Reference Quantity Remark
None
Safety conditions
None
Procedure
1 General information
Note
This service bulletin is classified as Mandatory or expected to be Mandatory by
an Airworthiness Directive (AD). The Procedure section of the Accomplishment
Instructions is Required for Compliance (RC) and must be done to comply with
the AD. The Job set-up and Job close-up sections, with the exception of the
return-to-service tests, are recommended and can be deviated from, done as part
of other actions, or done with accepted methods different from those given in the
service bulletin, as long as the RC section can be done and the aircraft can be
put back into a serviceable condition.
2 Job set-up
Note
The steps in the Job set-up section of this service bulletin are recommended
steps. The steps give a recommendation to get access to the work area. This
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  26
Original issue date: --2023-12-21

### Page 27

BD500-501003
recommendation is to give a safe work area and to minimize possible damage to
surrounding aircraft parts. Alternative steps can be used at the discretion of the
operator.
2.1 Make sure that the aircraft is in standard configuration for maintenance (refer to
AMP BD500-A-J12-00-00-01AAA-398A-A).
2.2 Open the Forward Cargo Compartment Door (FCCD) and the Aft Cargo
Compartment Door (ACCD) (refer to AMP BD500-A-J52-30-00-01AAA-540A-A).
Applicability: 50060, 50062-50063
▸
2.3 Remove the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124HRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
144BRW Aft cargo compartment door
surround panel
AMP BD500-A-
J50-12-01-01AAA-520A-A
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
2.4 Remove the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
124KRW Forward cargo compartment
panel
AMP BD500-A-
J50-11-01-01AAA-520A-A
144BRW Aft cargo compartment door
surround panel
AMP BD500-A-
J50-12-01-01AAA-520A-A
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  27
Original issue date: --2023-12-21

### Page 28

BD500-501003
▸
3 Procedure
3.1 If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a CRC representative
at 1 866 A220 CRC (1-866-222-0272) or 1-450-476-7676 or e-mail at
a220crc@airbus.com for analysis and to get an approved disposition to complete
this service bulletin.
3.2 Examine the lot number on the Environmental Control System (ECS) ducts (1),
(2), (3), and (4).
Refer to Table 6 and Fig. 1
Table 6 Environmental Control System (ECS) duct lot numbers
2105007133 2111001033 2107003544 2109034337
2105041052 2111001500 2109033947 2109034339
2107002212 2111001501 2109044372 2109044437
2107002352 2111038321 2109044374 2109044438
2107002763 2104048786 2110003776 2110028055
2107003043 2104048788 2110014032 2110028056
2107003611 2106005997 2110014033 2111000889
2109044474 2107002940 2104018055 2111000890
2109044476 2109044487 2104048950 2111001392
2110003613 2105042217 2105007075 2111001394
2110036846 2107002269 2107002303 2111038316
2110036848 2107002316 2107003273 2111038318
2111001032 2107003542 2107003275
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.3 For an ECS duct (1) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.3.1 Record the lot number of the ECS duct (1) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  28
Original issue date: --2023-12-21

### Page 29

BD500-501003
3.3.2 With indelible ink or equivalent, identify the ceiling panel D761105-121
(123ALC) as KC25060543001-101 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.4 For an ECS duct (1) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761105- 121 (123ALC)
as KC25060543001-201 and record the lot number of the ECS duct (1) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.5 For an ECS duct (2) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.5.1 Record the lot number of the ECS duct (2) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.5.2 With indelible ink or equivalent, identify the ceiling panel D761103-113
(123GLC) as KC25060543001-103 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.6 For an ECS duct (2) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D761103- 113 (123GLC)
as KC25060543001-203 and record the lot number of the ECS duct (2) in
Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-A-
J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063
▸
3.7 For an ECS duct (3) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.7.1 Record the lot number of the ECS duct (3) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  29
Original issue date: --2023-12-21

### Page 30

BD500-501003
3.7.2 With indelible ink or equivalent, identify the ceiling panel D761104-109
(123HLC) as KC25060543001-105 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
◂
Applicability: 50060, 50062-50063
▸
3.8 For an ECS duct (3) that has a lot number that is not contained in Table 6,
identify the ceiling panel D761104- 109 (123HLC) as KC25060543001-205 and
record the lot number of the ECS duct (3) in Appendix A (refer to AMP BD500-
A-J20-60-01-02AAA-913A-A and BD500-A-J50-10-03-02AAA-910B-A).
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
3.9 For an ECS duct (3) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.9.1 Record the lot number of the ECS duct (3) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
3.9.2 With indelible ink or equivalent, identify the ceiling panel D765101-113
(123MLC) as KC25060543001-113 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
3.10 For an ECS duct (3) that has a lot number that is not contained in Table 6,
with indelible ink or equivalent, identify the ceiling panel D765101- 113
(123MLC) as KC25060543001-213 and record the lot number of the ECS duct
(3) in Appendix A (refer to AMP BD500-A-J20-60-01-02AAA-913A-A and BD500-
A-J50-10-03-02AAA-910B-A).
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.11 For an ECS duct (4) that has a lot number that is contained in Table 6, do as
follows:
Refer to Fig. 1
3.11.1 Record the lot number of the ECS duct (4) in Appendix A (refer to
BD500-A-J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  30
Original issue date: --2023-12-21

### Page 31

BD500-501003
3.11.2 With indelible ink or equivalent, identify the ceiling panel D761134-111
(143ALC) as KC25060543001-107 (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A).
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
3.11.3 For an ECS duct (4) that has a lot number that is not contained
in Table 6, with indelible ink or equivalent, identify the ceiling panel
D761134-111 (143ALC) as KC25060543001-207 and record the lot
number of the ECS duct (4) in Appendix A (refer to AMP BD500-A-
J20-60-01-02AAA-913A-A and BD500-A-J50-10-03-02AAA-910B-A).
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  31
Original issue date: --2023-12-21

### Page 32

BD500-501003
Applicability: 50060, 50062-50063
LEGEND
1. ECS duct
2. ECS duct
3. ECS duct
4. ECS duct
1
2
3
4
FS475.6
(REF)
FS995.47
(REF)
FS1261.95
(REF)
FS668.5
(REF)
A220-100
ITEM CP1209543
P/N D761189-501
DESC ECS DUCT
REV. NCLOT 2203004495
TYPICAL
ICN-BD500-A-J501003-F-3AB48-95301-A-001-01
Fig. 1 Environmental Control System (ECS) ducts
- (Sheet 1 of 2)
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  32
Original issue date: --2023-12-21

### Page 33

BD500-501003
Applicability: 55128-55150, 55152, 55154-55155
LEGEND
1. ECS duct
2. ECS duct
3. ECS duct
4. ECS duct
1
2
3
4
FS391.6
(REF)
FS668.5
(REF)
FS995.47
(REF)
FS1324.95
(REF)
A220-300
ITEM CP1209543
P/N D761189-501
DESC ECS DUCT
REV. NCLOT 2203004495
TYPICAL
ICN-BD500-A-J501003-F-3AB48-95302-A-001-01
Fig. 1 Environmental Control System (ECS) ducts
- (Sheet 2 of 2)
◂
◂
◂
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  33
Original issue date: --2023-12-21

### Page 34

BD500-501003
4 Job close-up
Note
The steps in the Job close-up section of this service bulletin, except for the
return-to-service tests, are recommended steps. The steps give a recommendation
to install components removed during the Job set-up. This recommendation is
to make sure that the aircraft is safe and ready to return to service. Alternative
steps can be used at the discretion of the operator.
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
4.1 Remove all tools, equipment, and unwanted materials from the work area.
◂
Applicability: 50060, 50062-50063
▸
4.2 Install the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124HRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
144BRW Aft cargo door surround panel AMP BD500-A-
J50-12-01-01AAA-720A-A
◂
Applicability: 55128-55150, 55152, 55154-55155
▸
4.3 Install the access panels that follow:
PANEL NAME REFERENCE
124BRW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124ERW Forward cargo compartment
sidewall panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
124KRW Forward cargo compartment
panel
AMP BD500-A-
J50-11-01-01AAA-720A-A
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  34
Original issue date: --2023-12-21

### Page 35

BD500-501003
PANEL NAME REFERENCE
144BRW Aft cargo door surround panel AMP BD500-A-
J50-12-01-01AAA-720A-A
◂
Applicability: 50060, 50062-50063, 55128-55150, 55152, 55154-55155
▸
4.4 Close the FCCD and the ACCD (refer to AMP BD500-A-J52-30-00-01AAA-740A-
A).
◂
4.5 Send APPENDIX A to the CRC at A220_crc@abc.airbus for analysis.
5 Administrative
When PART B of this service bulletin is completed, record in the applicable aircraft
records that you have completed PART B of this service bulletin.
Requirements after job completion
Required conditions
Table 7  Required conditions
Action/Condition Data Module/Technical publication
None
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
End of data module
 2024-12-18 Page  35
Original issue date: --2023-12-21

### Page 36

BD500-501003
Intentionally left blank
See applicability on the first page of the DM
BD500-A-J50-10-03-02AAA-933A-A (002)
BD500-A-J50-10-03-02AAA-933A-A (002)
 2024-12-18 Page  36
Original issue date: --2023-12-21

### Page 37

BD500-501003
Safran Cabin Service Bulletin - F493000-50-06
References
Table 1 References
Data Module/Technical Publication Title
None
Description
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  37
Original issue date: --2023-12-21

### Page 38

BD500-501003
SAFRAN
CABIN
INC.
5701
Bolsa
A
ve
Huntington
Beach,
CA
92647
USA
T
elephone
+1
714-934-0000
www
.safran-cabin.com
(56135)
SER
VICE
BULLETIN
ST
ANDARD
CARGO
AND
ACCESSOR
Y
COMP
ARTMENTS
-
AFT/FWD
CARGO
CEILING
ASSEMBL
Y
-
INST
ALLA
TION
OF
THE
SLEEVE
ASSEMBL
Y
ON
THE
ECS
DUCT
ASSEMBL
Y
REVISION
TRANSMITT
AL
SHEET
A.
HIGHLIGHTS:
Service
Bulletin
№
F493000-50-06
Original
Issue
Date
Jul
06/23
Revision
№
1
Revision
Date
Oct
31/24
This
Service
Bulletin
is
revised
as
described
below
,
and
is
completely
reissued.
Discard
all
pages
of
previous
issue.
Page
№
Section
Description
3
1.A
Revised
to
delete
part
numbers
and
add
new
part
numbers.
5
2.A.
Added
the
note
to
reflect
the
correct
information.
6
2.C
Revised
to
update
the
quantity
of
some
items.
1
1,
13,
14,
and
15
3.B
Revised
to
reflect
the
correct
information.
16
3.C
Revised
to
update
the
details.
37
Figure
1
Revised
to
update
the
Flag
Note
1.
41,
42,
47,
52,
57,
and
61
Figure
2
Revised
to
update
the
details
and
add
new
part
numbers.
All
Pages
-
Added
revision
level
Rev
1:
Oct
31/24.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
TS
Page
1
of
2
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  38
Original issue date: --2023-12-21

### Page 39

BD500-501003
This
page
intentionally
left
blank.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
TS
Page
2
of
2
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  39
Original issue date: --2023-12-21

### Page 40

BD500-501003
SAFRAN
CABIN
INC.
5701
Bolsa
A
ve
Huntington
Beach,
CA
92647
USA
T
elephone
+1
714-934-0000
www
.safran-cabin.com
(56135)
SER
VICE
BULLETIN
ST
ANDARD
CARGO
AND
ACCESSOR
Y
COMP
ARTMENTS
-
AFT/FWD
CARGO
CEILING
ASSEMBL
Y
-
INST
ALLA
TION
OF
THE
SLEEVE
ASSEMBL
Y
ON
THE
ECS
DUCT
ASSEMBL
Y
The
technical
data
in
this
document
is
controlled
for
export
under
the
Export
Administration
Regulations
(EAR),
15
CFR
Parts
730-774,
ECCN:
EAR99.
V
iolations
of
these
laws
can
be
subject
to
fines
and
penalties
under
the
Export
Administration
Act.
Copyright
©
2024
Safran
Cabin
Inc.
This
document
contains
proprietary
information
of
Safran
Cabin
Inc.,
or
contains
proprietary
information
of
others,
and
is
issued
in
strict
confidence.
Except
for
rights
expressly
granted
by
contract,
this
document
can
not,
in
all
or
in
part,
be
duplicated,
reproduced
electronically
or
mechanically
,
disclosed,
or
used
for
design
or
manufacturing
purposes
without
written
authorization
from
Safran
Cabin
Inc.
W
ARNING:
ANY
W
ARRANTY
OFFERED
BY
SAFRAN
CABIN
INC.
WILL
BE
DEEMED
NULL
AND
VOID
IF
ITS
PRODUCTS
ARE
USED
IN
AN
UNINTENDED
MANNER
OR
SHOW
INDICA
TIONS
THA
T
THEY
HA
VE
BEEN
AL
TERED
IN
ANYW
A
Y
,
INCLUDING,
BUT
NOT
LIMITED
T
O,
USE
OF
REPLACEMENT
P
AR
TS
OR
MAINTENANCE
ACTIONS
NOT
PERFORMED
AS
OUTLINED
IN
THIS
MANUAL
A
T
THE
TIME
AND
IN
THE
MANNER
SPECIFIED
HEREIN.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
1
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  40
Original issue date: --2023-12-21

### Page 41

BD500-501003
SER
VICE
BULLETIN
1.
PLANNING
INFORMA
TION
A.
EFFECTIVITY
This
Service
Bulletin
(SB)
applies
to
the
Ceiling
Assembly
,
as
listed
below:
Group
Aicraft
Model
Part
Number
Nomenclature
D761
105-121
D761
105-121-N0004
D761
105-1
17
D761
103-107
D761
103-109
D761
103-1
13
D761
103-1
13-N0004
D761
104-107
D761
104-109
D761
104-109-N0002
FWD
Ceiling
Assembly
D761
134-1
1
1
D761
134-1
1
1-N0004
D761
134-107
1
A220-100
D761
134-109
AFT
Ceiling
Assembly
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
2
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  41
Original issue date: --2023-12-21

### Page 42

BD500-501003
SER
VICE
BULLETIN
Group
Aicraft
Model
Part
Number
Nomenclature
D765101-109
D765101-1
13
D765101-1
13-N0002
D765101-1
13-N0004
D761
105-1
17
D761
105-121
D761
105-121-N0003
D761
105-121-N0004
D761
103-109
D761
103-1
1
1
D761
103-1
13
D761
103-1
13-N0002
D761
103-1
13-N0003
D761
103-1
13-N0004
FWD
Ceiling
Assembly
D761
134-1
1
1
D761
134-1
1
1-N0004
D761
134-1
1
1-S0001
AFT
Ceiling
Assembly
D761
134-107
2
A220-300
D761
134-109
AFT
Ceiling
Assembly
B.
CONCURRENT
REQUIREMENTS
None.
C.
REASON
Investigation
has
revealed
that
the
2IN
and
3IN
ECS
Ducts
from
Cargo
Compartment
need
to
be
protected
with
a
fidex
sleeve
assembly
to
comply
with
the
flammability
requirements.
D.
DESCRIPTION
This
Service
Bulletin
gives
instructions
as
listed
below:
(1)
Applicable
to
AFT
and
FWD
Cargo
Compartment
Assembly
(a)
Get
access
to
the
Ceiling
Assembly
.
(b)
Remove
and
keep
the
existing
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
with
the
attaching
parts.
(c)
Drill
the
holes
and
install
the
inserts,
as
required.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
3
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  42
Original issue date: --2023-12-21

### Page 43

BD500-501003
SER
VICE
BULLETIN
(d)
Reinstall
the
kept
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
using
the
attaching
parts.
(e)
Install
the
new
Sleeve
Assembly
using
the
attaching
parts.
(f)
Install
the
SB
Incorporation
Placard.
E.
COMPLIANCE
This
Service
Bulletin
is
recommended
.
It
can
or
will
be
implemented
at
the
earliest
opportunity
where
manpower
and
facilities
are
available
or
at
the
next
suitable
planned
maintenance
period.
F
.
APPROV
AL
The
technical
content
of
this
Service
Bulletin
has
been
reviewed
and
accepted
by
Airbus.
G.
MANPOWER
Approximately
2
man-hours
are
necessary
to
modify
one
Ceiling
Assembly
.
NOTE
:
The
above
time
estimate
does
not
include
adhesive
curing
time.
H.
WEIGHT
AND
BALANCE
None.
I.
ELECTRICAL
LOAD
DA
T
A
Not
changed.
J.
SOFTW
ARE
ACCOMPLISHMENT
SUMMAR
Y
Not
changed.
K.
REFERENCES
The
following
documents
were
used
as
data
sources
in
preparation
of
this
Service
Bulletin:
REFERENCES
T
able
1
Document
№
T
itle
CDKF49-3-53
ECS
Duct
Improvement-
A220-100
CDKF49-3-54
ECS
Duct
Improvement-
A220-300
L.
OTHER
PUBLICA
TIONS
AFFECTED
Component
Maintenance
Manual
(CMM)
-
Chapter
50-1
1-10
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
4
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  43
Original issue date: --2023-12-21

### Page 44

BD500-501003
SER
VICE
BULLETIN
M.
INTERCHANGEABILITY
OR
INTERMIXABILITY
OF
P
AR
TS
Not
applicable.
2.
MA
TERIAL
INFORMA
TION
A.
MA
TERIAL
-
PRICE
AND
A
V
AILABILITY
The
materials
required
for
the
accomplishment
of
the
tasks
in
this
SB
are
listed
in
paragraph
2.C.
and
are
available
at
no
cost
.
This
commercial
condition
is
valid
for
2
years
from
the
SB
initial
issue
date
or
first
issue
that
incorporates
operator
fleet.
For
availability
and
ordering
information,
refer
to
Safran
Cabin
Inc.
NOTE
:
When
requested,
Safran
Cabin
must
supply
a
credit
note
for
the
ef
fective
man-hours
rework
without
exceeding
the
Service
Bulletin
recommendations.
The
agreement
in-house
warranty
labor
rate
for
the
accomplishment
of
this
Service
Bulletin
is
36
months
after
the
initial
issue
date
of
the
Service
Bulletin.
Name
and
Address
Phone
Cage
Code
Safran
Cabin
Inc.
7330,
Lincoln
W
ay
Garden
Grove,
CA
92841
-
USA
(657)
227-5505
56135
B.
INDUSTR
Y
SUPPOR
T
INFORMA
TION
SUPPLIER
INFORMA
TION
T
able
2
Name
and
Address
V
endor
Code
DYSOL
INC
5475
E
ST
A
TE
HWY
1
14,
RHOME,
TX
76078
1MFE1
C.
MA
TERIAL
NECESSAR
Y
FOR
EACH
SP
ARE
(1)
Modification
The
parts
necessary
to
modify
one
aircraft
are
included
in
kit:
GROUP
AIRCRAFT
MODEL
APPLICABLE
CDK
FIGURE
REFERENCE
1
A220-100
CDKF49-3-53
1
2
A220-300
CDKF49-3-54
2
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
5
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  44
Original issue date: --2023-12-21

### Page 45

BD500-501003
SER
VICE
BULLETIN
CDKF49-3-53
:
ECS
Duct
Improvement-
A220-100
T
able
3
New
PN
Description
Old
PN
Qty
Used
Disposition
CDIN07-3-10B
Insert
-
37
Install
New
NAS603-4
Screw
-
37
Install
New
AN970-3
W
asher
-
29
Install
New
NAS1922-0225-3
Clamp
-
03
Install
New
D763339-23
Doubler
-
03
Install
New
D763239-507
Sleeve
Assembly
-
02
Install
New
NAS1922-0350-3
Clamp
-
01
Install
New
D763339-21
Doubler
-
01
Install
New
D763239-505
Sleeve
Assembly
-
01
Install
New
D763239-509
Sleeve
Assembly
-
01
Install
New
CDPL604-1-F493000-50-06
SB
Incorporation
Placard
-
04
Install
New
CDKF49-3-54
:
ECS
Duct
Improvement-
A220-300
T
able
4
New
PN
Description
Old
PN
Qty
Used
Disposition
CDIN07-3-10B
Insert
-
37
Install
New
D763239-507
Sleeve
Assembly
-
02
Install
New
NAS1922-0225-3
Clamp
-
03
Install
New
D763339-23
Doubler
-
03
Install
New
NAS603-4
Screw
-
37
Install
New
AN970-3
W
asher
-
29
Install
New
D763239-509
Sleeve
Assembly
-
01
Install
New
NAS1922-0350-3
Clamp
-
01
Install
New
D763339-21
Doubler
-
01
Install
New
D763239-505
Sleeve
Assembly
-
01
Install
New
CDPL604-1-F493000-50-06
SB
Incorporation
Placard
-
04
Install
New
(2)
Material
Supplied
by
end
user
Standard
tool
box
plus
the
following
materials:
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
6
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  45
Original issue date: --2023-12-21

### Page 46

BD500-501003
SER
VICE
BULLETIN
Nomenclature
Part
or
Specification
№
Source
Methyl-Ethyl-Ketone
(MEK)
(
1
)
TT
-M-216
Commercially
A
vailable
Isopropyl
Alcohol
(
1
)
TT
-I-735
Commercially
A
vailable
Acetone
(
1
)
O-A-51H
Commercially
A
vailable
Solvent
Blend
DS-108
Dysol
Inc.
Potting
Compound
(Insert
Installation)
AEROBOND
1507
A/B
Safran
Cabin
Inc.
NOTE
:
(
1
)
Equivalent
materials
may
be
used.
D.
REIDENTIFIED
P
AR
TS
Not
applicable.
E.
T
OOLING
-
PRICE
AND
A
V
AILABILITY
None.
3.
ACCOMPLISHMENT
INSTRUCTIONS
A.
General
The
steps
below
give
the
general
accomplishment
instructions.
The
detailed
sequence
is
given
as
notes
in
the
Figures
.
W
ARNING
:
MAKE
SURE
THA
T
THE
AIRCRAFT
IS
SAFE
FOR
MAINTENANCE.
W
ARNING
:
THE
MEK
SOL
VENT
,
ACET
ONE,
ISOPROPYL
ALCOHOL,
AND
SOL
VENT
BLEND
ARE
POISONOUS
AND
FLAMMABLE.
KEEP
A
W
A
Y
FROM
HEA
T
AND
OPEN
FLAME.
USE
IN
AN
AREA
THA
T
HAS
GOOD
AIRFLOW
.
DO
NOT
SW
ALLOW
.
IT
IS
RECOMMENDED
T
O
USE
RESPIRA
T
OR,
GOGGLES,
AND
GLOVES
T
O
PREVENT
FUME
CONT
ACT
WITH
EYES
AND
NOSE.
DO
NOT
BREA
THE
THE
FUMES.
IF
SOLUTION
T
OUCH
SKIN
OR
EYES,
FLUSH
AREA
WITH
CLEAN
W
A
TER
AND
GET
MEDICAL
AID
AS
NECESSAR
Y
.
B.
For
the
ECS
Duct
Improvement
,
do
as
follows:
NOTE
:
The
instructions
below
are
applicable
to
each
Ceiling
Assembly
.
T
o
make
the
implementation
of
the
modification
easier
,
refer
to
the
applicable
publication
listed
in
paragraph
1.L.
(1)
Applicable
to
Group
1
(a)
Part
I
-
AFT
Cargo
Compartment
Assembly
(See
Figure
1,
Detail
A)
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
7
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  46
Original issue date: --2023-12-21

### Page 47

BD500-501003
SER
VICE
BULLETIN
1
Get
access
to
the
Ceiling
Assembly
(PN
D761
134-1
1
1
or
PN
D761
134-1
1
1-N0004
or
PN
D761
134-107
or
PN
D761
134-109
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
1,
Details
A
and
C
.
2
Remove
and
keep
the
existing
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Details
A,
C
and
D
.
3
Drill
ten
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
1,
Details
A,
C
and
D,
and
Section
E-E
.
4
Install
the
Insert
(PN
CDIN07-3-10B)
(10
positions,
marked
“A”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
1,
Details
A,
C
and
D,
and
Section
E-E
.
5
Align
the
Sleeve
Assembly
(PN
D763239-505)
with
new
insert
(10
positions,
marked
“B”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
1,
Detail
G
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
6
Reinstall
the
kept
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Section
E-E
and
Detail
F
.
7
Install
the
Sleeve
Assembly
(PN
D763239-505)
supplied
in
the
kit,
on
the
ECS
Duct
Assembly
.
See
Figure
1,
Details
F
and
G
.
8
Install
the
Screw
(PN
NAS603-4)
(8
positions)
and
W
asher
(PN
AN970-3)
(8
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-505)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
F
and
G
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
9
Install
the
Doubler
(PN
D763339-21)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-505)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
G
and
H
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
10
Install
the
Clamp
(PN
NAS1922-0350-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-505)
on
ECS
Duct
Assembly
.
See
Figure
1,
Details
G
and
H,
Sections
J-J
and
K-K
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
1
1
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
8
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  47
Original issue date: --2023-12-21

### Page 48

BD500-501003
SER
VICE
BULLETIN
(b)
Part
II
-
FWD
Cargo
Compartment
Assembly
(See
Figure
1,
Detail
B)
1
Get
access
to
the
Ceiling
Assembly
(PN
D761
105-121
or
PN
D761
105-121-N0004
or
PN
D761
105-1
17
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
1,
Details
B
and
L
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Details
B,
L
and
M
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
1,
Details
B,
L
and
M,
and
Section
N-N
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“C”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
1,
Details
B,
L
and
M,
and
Section
N-N
.
d
Align
the
Sleeve
Assembly
(PN
D763239-507)
with
new
insert
(9
positions,
marked
“D”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
1,
Detail
Q
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
e
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Section
N-N
and
Detail
P
.
f
Install
the
Sleeve
Assembly
(PN
D763239-507)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
P
and
Q
.
g
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
P
and
Q
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
h
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
Q
and
R
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
i
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-507)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
Q
and
R,
Sections
S-S
and
T
-T
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
9
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  48
Original issue date: --2023-12-21

### Page 49

BD500-501003
SER
VICE
BULLETIN
j
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
2
Get
access
to
the
Ceiling
Assembly
(
PN
D761
103-107
or
PN
D761
103-109
or
PN
D761
103-1
13
or
PN
D761
103-1
13-N0004
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
1,
Details
B
and
U
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Details
B,
U
and
V
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
1,
Details
B,
U
and
V
,
and
Section
W
-W
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“E”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
1,
Details
B,
U
and
V
,
and
Section
W
-W
.
d
Align
the
Sleeve
Assembly
(PN
D763239-509)
with
new
insert
(9
positions,
marked
“F”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
1,
Detail
Y
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
e
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Section
W
-W
and
Detail
X
.
f
Install
the
Sleeve
Assembly
(PN
D763239-509)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
X
and
Y
.
g
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-509)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
X
and
Y
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
h
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-509)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
Y
and
Z
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
i
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-509)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
Y
and
Z,
Sections
AA-AA
and
AB-AB
.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
10
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  49
Original issue date: --2023-12-21

### Page 50

BD500-501003
SER
VICE
BULLETIN
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
j
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
3
Get
access
to
the
Ceiling
Assembly
(
PN
D761
104-107
or
PN
D761
104-109
or
PN
D761
104-109-N0002
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
1,
Details
B
and
AC
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Details
B,
AC,
and
AD
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
1,
Details
B,
AC
and
AD,
and
Section
AE-AE
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“J”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
1,
Details
B,
AC
and
AD,
and
Section
AE-AE
.
d
Cut
the
hatch
area
of
the
existing
Foam
in
accordance
with
Figure
1,
Section
AE-AE
and
Detail
AF
.
NOTE
:
Do
not
cut
the
Ceiling
Panel
Assembly
.
e
Align
the
drill
Sleeve
Assembly
(PN
D763239-507)
with
new
insert
(9
positions,
marked
“K”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
1,
Detail
AH
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
f
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
1,
Section
AE-AE
and
Detail
AG
.
g
Install
the
Sleeve
Assembly
(PN
D763239-507)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
AG
and
AH
.
h
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
AG
and
AH
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
i
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
1,
Details
AH
and
AJ
.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
1
1
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  50
Original issue date: --2023-12-21

### Page 51

BD500-501003
SER
VICE
BULLETIN
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
j
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-507)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
1,
Details
AH
and
AJ,
Sections
AK-AK
and
AL-AL
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
k
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
(2)
Applicable
to
Group
2
(a)
Part
I
-
AFT
Cargo
Compartment
Assembly
(See
Figure
2,
Detail
A)
1
Get
access
to
the
Ceiling
Assembly
(PN
D761
134-1
1
1
or
PN
D761
134-1
1
1-N0004
or
PN
D761
134-1
1
1-S0001
or
PN
D761
134-107
or
PN
D761
134-109
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
2,
Details
A
and
C
.
2
Remove
and
keep
the
existing
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Details
A,
C
and
D
.
3
Drill
ten
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
2,
Details
A,
C
and
D,
and
Section
E-E
.
4
Install
the
Insert
(PN
CDIN07-3-10B)
(10
positions,
marked
“A”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
2,
Details
A,
C
and
D,
and
Section
E-E
.
5
Align
the
Sleeve
Assembly
(PN
D763239-505)
with
new
insert
(10
positions,
marked
“B”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
2,
Detail
G
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
6
Reinstall
the
kept
ECS
Duct
Assembly
,
ECS
Duct
3IN
Inlet
Cage
Assembly
,
and
ECS
Duct
3IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Section
E-E
and
Detail
F
.
7
Install
the
Sleeve
Assembly
(PN
D763239-505)
supplied
in
the
kit,
on
the
ECS
Duct
Assembly
.
See
Figure
2,
Details
F
and
G
.
8
Install
the
Screw
(PN
NAS603-4)
(8
positions)
and
W
asher
(PN
AN970-3)
(8
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-505)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
F
and
G
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
12
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  51
Original issue date: --2023-12-21

### Page 52

BD500-501003
SER
VICE
BULLETIN
9
Install
the
Doubler
(PN
D763339-21)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-505)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
G
and
H
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
10
Install
the
Clamp
(PN
NAS1922-0350-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-505)
on
ECS
Duct
Assembly
.
See
Figure
2,
Details
G
and
H,
Sections
J-J
and
K-K
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
1
1
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
(b)
Part
II
-
FWD
Cargo
Compartment
Assembly
(See
Figure
2,
Detail
B)
1
Get
access
to
the
Ceiling
Assembly
(PN
D761
105-121
or
PN
D761
105-121-N0003
or
PN
D761
105-121-N0004
or
PN
D761
105-1
17
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
2,
Details
B
and
L
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Details
B,
L
and
M
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
2,
Details
B,
L
and
M,
and
Section
N-N
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“C”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
2,
Details
B,
L
and
M,
and
Section
N-N
.
d
Align
the
Sleeve
Assembly
(PN
D763239-507)
with
new
insert
(9
positions,
marked
“D”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
2,
Detail
Q
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
e
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Section
N-N
and
Detail
P
.
f
Install
the
Sleeve
Assembly
(PN
D763239-507)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
P
and
Q
.
g
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
P
and
Q
.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
13
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  52
Original issue date: --2023-12-21

### Page 53

BD500-501003
SER
VICE
BULLETIN
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
h
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
Q
and
R
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
i
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-507)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
Q
and
R,
Sections
S-S
and
T
-T
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
j
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
2
Get
access
to
the
Ceiling
Assembly
(PN
D761
103-1
13
or
PN
D761
103-1
13-N0002
or
PN
D761
103-1
13-N0003
or
PN
D761
103-1
13-N0004
or
PN
D761
103-109
or
PN
D761
103-1
1
1
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
2,
Details
B
and
U
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Details
B,
U
and
V
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
2,
Details
B,
U
and
V
,
and
Section
W
-W
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“E”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
2,
Details
B,
U
and
V
,
and
Section
W
-W
.
d
Align
the
Sleeve
Assembly
(PN
D763239-509)
with
new
insert
(9
positions,
marked
“F”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
2,
Detail
Y
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
e
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Section
W
-W
and
Detail
X
.
f
Install
the
Sleeve
Assembly
(PN
D763239-509)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
X
and
Y
.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
14
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  53
Original issue date: --2023-12-21

### Page 54

BD500-501003
SER
VICE
BULLETIN
g
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-509)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
X
and
Y
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
h
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-509)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
Y
and
Z
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
i
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-509)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
Y
and
Z,
Sections
AA-AA
and
AB-AB
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
j
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
3
Get
access
to
the
Ceiling
Assembly
(PN
D765101-1
13
or
PN
D765101-1
13-N0002
or
PN
D765101-1
13-N0004
or
PN
D765101-109
)
and
find
the
existing
ECS
Duct
Assembly
.
See
Figure
2,
Details
B
and
AC
.
a
Remove
and
keep
the
existing
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
with
the
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Details
B,
AC,
and
AD
.
b
Drill
nine
holes
.452
-
.457
in
(1
1,48
-
1
1,61
mm)
DIA
X
.340
in
(8,64
mm)
DEEP
in
accordance
with
marked
position.
See
Figure
2,
Details
B,
AC
and
AD,
and
Section
AE-AE
.
c
Install
the
Insert
(PN
CDIN07-3-10B)
(9
positions,
marked
“G”)
supplied
in
the
kit,
in
accordance
with
paragraph
3.D.
See
Figure
2,
Details
B,
AC
and
AD,
and
Section
AE-AE
.
d
Cut
the
hatch
area
of
the
existing
Foam
in
accordance
with
Figure
2,
Section
AE-AE
and
Detail
AF
.
NOTE
:
Do
not
cut
the
Ceiling
Panel
Assembly
.
e
Align
the
Sleeve
Assembly
(PN
D763239-507)
with
new
insert
(9
positions,
marked
“H”)
and
mark
the
holes
position
before
the
Sleeve
Assembly
installation
on
the
Ceiling
Panel.
See
Figure
2,
Detail
AH
.
NOTE
:
These
holes
must
have
a
maximum
.300
in
(7,62
mm)
DIA.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
15
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  54
Original issue date: --2023-12-21

### Page 55

BD500-501003
SER
VICE
BULLETIN
f
Reinstall
the
kept
Inlet
2IN
ECS
Duct
Assembly
,
ECS
Duct
2IN
Inlet
Cage
Assembly
,
and
ECS
Duct
2IN
Inlet
Cage
Base
using
the
existing
Screw
(8
positions)
and
W
asher
(8
positions).
See
Figure
2,
Section
AE-AE
and
Detail
AG
.
g
Install
the
Sleeve
Assembly
(PN
D763239-507)
supplied
in
the
kit,
on
the
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
AG
and
AH
.
h
Install
the
Screw
(PN
NAS603-4)
(7
positions)
and
W
asher
(PN
AN970-3)
(7
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
AG
and
AH
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
NOTE
:
All
pleats
on
Sleeve
Assembly
base
must
be
secured
by
W
ashers.
i
Install
the
Doubler
(PN
D763339-23)
using
the
Screw
(PN
NAS603-4)
(2
positions)
supplied
in
the
kit,
to
attach
the
Sleeve
Assembly
(PN
D763239-507)
on
the
Ceiling
Assembly
.
See
Figure
2,
Details
AH
and
AJ
.
NOTE
:
The
Sleeve
Assembly
must
be
flush
with
foam
tape.
j
Install
the
Clamp
(PN
NAS1922-0225-3)
supplied
in
the
kit,
to
hold
the
Sleeve
Assembly
(PN
D763239-507)
on
Inlet
2IN
ECS
Duct
Assembly
.
See
Figure
2,
Details
AH
and
AJ,
Sections
AK-AK
and
AL-AL
.
NOTE
:
The
Clamp
must
be
torqued
to
6-8
in-lbs.
k
Install
the
SB
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
in
accordance
with
paragraph
3.C.
.
C.
Service
Bulletin
(SB)
Incorporation
Placard
Installation
NOTE
:
Before
the
SB
Incorporation
Placard
Installation,
clean
the
surface
with
a
lint-free
shop
wipe
soaked
with
Isopropyl
Alcohol
or
equivalent.
(1)
Peel
of
f
and
discard
the
adhesive
backing
from
the
Service
Bulletin
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
and
push
it
near
the
Ceiling
Assembly
I.D.
Placard.
See
Figure
1,
Details
A,
B,
C,
L,
U,
AD,
and
AM
.
(2)
Peel
of
f
and
discard
the
adhesive
backing
from
the
Service
Bulletin
Incorporation
Placard
(PN
CDPL604-1-F493000-50-06
),
supplied
in
the
kit,
and
push
it
near
the
Ceiling
Assembly
I.D.
Placard.
See
Figure
2,
Details
A,
B,
C,
L,
U,
AC,
and
AM
.
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
16
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  55
Original issue date: --2023-12-21

### Page 56

BD500-501003
SER
VICE
BULLETIN
D.
Insert
Installation
Procedure
(See
Figures
3
)
The
steps
below
give
the
general
instructions
for
the
insert
installation.
W
ARNING
:
THIS
PROCEDURE
APPLIES
T
O
SEALANTS,
POTTING
COMPOUNDS,
AND
OTHER
HAZARDOUS
MA
TERIALS.
SEE
THE
MANUF
ACTURER’S
SPECIFIC
SAFETY
AND
HEAL
TH
INSTRUCTIONS
FOR
USE
OF
THESE
MA
TERIALS.
CAREFULL
Y
READ
THE
APPLICABLE
“MA
TERIAL
SAFETY
DA
T
A
SHEET”
AND
OBEY
ALL
WRITTEN
SAFETY
AND
HEAL
TH
INSTRUCTIONS
BEFORE
USING
THESE
MA
TERIALS.
W
ARNING
:
OBEY
THE
MANUF
ACTURER’S
INSTRUCTIONS
WHEN
YOU
USE
CHEMICAL
PRODUCTS
AS
ADHESIVES.
THESE
PRODUCTS
ARE
T
OXIC
AND
CAN
CAUSE
INJURIES
T
O
YOU.
(1)
Identify
and
mark
the
new
locations
for
the
inserts.
(2)
For
Blind
Inserts
and
Blind
Inserts
with
Clearance
Hole,
do
as
follows:
(a)
Use
a
flat-bottom
drill
or
counterbore
tool
to
drill
down
to,
but
not
in
contact
with,
the
opposite
face
of
the
panel.
Do
not
damage
none
of
the
skin
face.
(b)
Undercut
core
panels
with
composite
skins
to
a
diameter
1-1/2
to
2
times
the
installation
hole
diameter
down
to
the
opposite
skin.
Do
not
damage
none
of
the
skin
face.
(3)
Remove
all
debris
and
particles
from
the
drilled
hole
with
a
vacuum
or
dry
compressed
air
.
It
is
important
to
remove
all
debris,
including
half
drilled
and
loosened
cell
walls,
to
make
sure
that
the
potting
compound
will
touch
the
core
material.
(4)
Use
clean
lint-free
cloths
and
Acetone
or
Isopropyl
Alcohol
to
wipe
away
oily
dirt
and
debris.
Let
the
solvent
dry
from
the
honeycomb
for
at
least
15
minutes
at
room
temperature.
(5)
Clean
the
replacement
insert
by
vapor
degreasing,
solvent
washing,
or
other
means.
The
cleaned
insert
should
be
handled
with
clean
gloves.
NOTE
:
Pressure-sensitive
alignment
tabs
or
other
installation
aids
may
be
attached
to
the
inserts.
Install
the
tabs
after
the
cleaning.
(6)
Mix
the
potting
compound
(resin
and
hardener)
in
the
approximate
mix
ratio
given
below
.
Mix
no
more
than
it
can
be
used
in
the
pot
life
of
the
compound.
Mix
the
resin
and
hardener
components
fully
but
do
not
let
too
much
air
into
the
mixture.
NOTE
:
Always
follow
the
instructions
given
by
the
manufacturer
.
The
mix
ratio
may
have
changed
after
publication
of
this
service
bulletin.
T
o
use
the
adhesive,
follow
the
instructions
below:
Potting
Compound
Mix
Ratio
By
W
eight
Resin/Hardener
Approx.
Pot
Life
Shelf
Life
AEROBOND
1507
A/B
100/15
20
minutes
12
months
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
17
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  56
Original issue date: --2023-12-21

### Page 57

BD500-501003
SER
VICE
BULLETIN
(7)
Fill
the
hole
in
the
panel
1/4
to
2/3
full
with
potting
compound.
NOTE
:
T
o
help
align
the
tab
and
insert,
a
vendor
(insert
MFG)
guide
tool,
a
paper
clip,
pin
or
similar
tool
can
be
used
if
necessary
as
a
shop
aid.
It
is
not
a
requirement,
but
a
recommendation
only
.
Do
not
remove
the
tab.
(8)
Applicable
to
Blind
Inserts
with
Clearance
Hole
only
-
Install
a
small
piece
of
masking
tape
over
the
bottom
clearance
hole
of
the
insert.
(9)
Slowly
turn
the
insert
while
lowering
it
into
the
panel
to
prevent
voids
in
the
potting
compound.
Push
the
tab
tightly
against
the
panel.
CAUTION
:
T
OO
F
AST
INJECTION
OF
POTTING
COMPOUND
WILL
FORCE
THE
INSER
T
A
W
A
Y
FROM
THE
P
ANEL.
(10)
Use
the
sealant
gun
to
slowly
add
the
potting
compound
into
one
hole
of
the
insert
until
some
compound
comes
out
of
the
other
hole.
NOTE
:
If
insert
is
bonded
in
a
vertical
surface,
add
the
Potting
Compound
from
the
bottom
hole,
and
let
the
air
flow
from
the
upper
hole.
(1
1)
Let
the
potting
compound
to
cure
for
8
hours
at
ambient
temperature
and
4
hours
at
120°F
(49°C).
(12)
Remove
the
tab
and
the
tapes
and
trim
the
small
plugs
of
the
potting
compound
that
extend
from
the
holes
in
the
insert.
(13)
Make
sure
that
the
inserts
is
correctly
installed.
Install
the
insert
no
more
than
0.030
inch
(0,076
cm)
above
or
below
the
face
of
the
panel.
The
insert
must
not
be
of
f-center
or
installed
at
an
angle.
(14)
Applicable
to
Blind
Inserts
with
Clearance
Hole
only
-
Open
the
clearance
hole
through
the
insert
down
to
opposite
panel
skin,
using
a
drill
and
fine
drill
bit
as
necessary
by
hole
requirements
and
the
installed
insert
as
a
pilot
or
bushing
to
guide
the
drilling.
(15)
Repeat
steps
3.D.(1)
thru
3.D.(14)
for
all
inserts
to
be
installed.
E.
T
orque
Information
All
fasteners
must
be
tightened
at
installation
to
the
torque
indicated
in
the
T
able
below:
General
Screws
Thread
Size
T
orque
Range
(in-lb)
T
orque
Range
(Nm)
10-32
25
or
hand
tight
only
.
2,82
or
hand
tight
only
.
1/4-28
78
-
82
8,81
-
9,26
5/16-24
145
-
155
16,38
-
17,51
3/8-24
233
-
247
26,33
-
27,91
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
18
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  57
Original issue date: --2023-12-21

### Page 58

BD500-501003
SER
VICE
BULLETIN
General
Screws
into
Panel
Inserts
Thread
Size
T
orque
Range
(in-lb)
T
orque
Range
(Nm)
4-40
6
0,68
6-32
12
1,36
8-32
15
1,69
10-32
20
2,26
1/4-28
40
4,52
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
19
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  58
Original issue date: --2023-12-21

### Page 59

BD500-501003
SER
VICE
BULLETIN
(REF.)
COMPT ASSY
AFT CARGO 
(REF.)
COMPT ASSY
FWD CARGO 
A C
S
C
A
2
2
0
−
S
B
F
4
9
3
0
0
0
−
5
0
−
0
6
−
0
1
0
1
L
A
B
C
U
APPLICABLE
T
O
GROUP
1
-
AFT/FWD
CARGO
CEILING
ASSEMBL
Y
-
INST
ALLA
TION
OF
THE
SLEEVE
ASSEMBL
Y
ON
THE
ECS
DUCT
ASSEMBL
Y
(Sheet
1
of
21)
FIGURE
1
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
20
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  59
Original issue date: --2023-12-21

### Page 60

BD500-501003
SER
VICE
BULLETIN
(REF.)
PN D761134−111−N0004
PN D761134−111 OR
PN D761134−109  OR
PN D761134−107
AFT CEILING ASSY
8 POSITIONS
(REMOVE AND KEEP)
EXISTING WASHER
8 POSITIONS
(REMOVE AND KEEP)
EXISTING SCREW
(REMOVE AND KEEP)
ECS DUCT ASSY 
EXISTING 
(REMOVE AND KEEP)
INLET CAGE BASE 
ECS DUCT 3IN 
EXISTING
(REMOVE AND KEEP)
INLET CAGE ASSY
ECS DUCT 3IN 
EXISTING
(REF.)
PANEL ASSY
CEILING 
A M
C
D
D
E
E
S
C
A
2
2
0
−
S
B
F
4
9
3
0
0
0
−
5
0
−
0
6
−
0
1
0
2
APPLICABLE
T
O
GROUP
1
-
AFT/FWD
CARGO
CEILING
ASSEMBL
Y
-
INST
ALLA
TION
OF
THE
SLEEVE
ASSEMBL
Y
ON
THE
ECS
DUCT
ASSEMBL
Y
(Sheet
2
of
21)
FIGURE
1
Initial
Issue
:
Jul
06/23
F493000-50-06
Revision
1
:
Oct
31/24
Page
21
of
62
See applicability on the first page of the DM
BD500-A-J50-10-03-01AAA-910B-A (003)
BD500-A-J50-10-03-01AAA-910B-A (003)
 2024-12-18 Page  60
Original issue date: --2023-12-21

The text continues at https://openairdocs.org/service-documents/airbus-canada/bd500-501003/file/5d00a96e0659.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
