# Eurocopter Emergency Alert Service Bulletin 05A010

Copy: Revision 2 ("U.S. DOT/FAA - Eurocopter ASB 05A010"), 14 pages: PDF https://openairdocs.org/files/sha256/23/cf/23cf143dd60de02c826f58120b6a7fe7e1913eb49abd04a53c8d62e05b3effde; text https://openairdocs.org/service-documents/airbus-helicopters/05a010/file/23cf143dd60d.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0038; AD 2015-09-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 05A010
- Latest revision known: 05A010, Revision 2, dated April 22, 2013 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/05a010

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-09-01](https://openairdocs.org/ad/2015-09-01.md), effective Jun 9, 2015: Revision 2

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/05a010/proposed.md).

## Text (14 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0038; AD 2015-09-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T.F.S. No. 00000745 
      Page 1/14 
2013.04.22 
This document is available on the internet: www.eurocopter.com/techpub 
 
EUROCOPTER  
DIRECTION TECHNIQUE SUPPORT 
13725 MARIGNANE  CEDEX FRANCE 
 
EMERGENCY 
ALERT SERVICE BULLETIN 
 
SUPER PUMA NUMBER VERSIONS 
EC225 05A010 
Civil:  LP 
  
EC725 05A010 
Military: AP 
  
 
 
 
 
 
SUBJECT: TIME LIMITS – MAINTENANCE CHECKS 
 
Check of the bonding of the stainless steel protective strip on the leading 
edge of main rotor blades 
 
 
ATA: 62 
 
 
REVISION No. DATE OF APPROVAL DATE OF ISSUE 
   
   
Revision 0 On: June 28, 2007 2007.06.28 
Revision 1 
Revision 2 
On: July 27, 2007 
On: April 22, 2013 
2007.07.30 
2013.04.22

### Page 2

T.F.S. No. 00000745 
      Page 2/14 
2013.04.22 
 
 
 
1. PLANNING INFORMATION 
 
1.A. EFFECTIVITY 
 
1.A.1. Helicopters / Installed equipment 
 
Helicopters equipped with main rotor blades P/N: 
- 332A11.0050.00 
- 332A11.0050.02 
- 332A11.0055.00 
- 332A11.0055.02 
 
1.A.2. Non-installed equipment 
 
  Not applicable. 
 
 
1.B. ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C. REASON 
 
To check the bonding of the stainless steel protective strips on the leading edge of the main rotor 
blades at regular intervals.  
 
The purpose of Revision 1 of this ALERT SERVICE BULLETIN was: 
- To enable operators to perform the visual check and the tapping test, scheduled at 85 flying hours, 
on the leading edge stainless steel protective strip, without removal of the main rotor blades from the 
helicopter. 
 
Revision 1 had no effect on compliance with Revision 0 of this ALERT SERVICE BULLETIN. 
 
The purpose of Revision 2 of this ALERT SERVICE BULLETIN is to extend the effectivity to main rotor 
blade part numbers 332A11.0050.02 and 332A11.0055.02. 
Revision 2 does not affect compliance with Revision 1 of this ALERT SERVICE BULLETIN.

### Page 3

T.F.S. No. 00000745 
      Page 3/14 
2013.04.22 
 
 
 
1.D. DESCRIPTION 
 
Revision 0: 
The initial investigations conducted on the main rotor blade showing significant de-bonding of the 
stainless steel protective strip (see TELEX INFORMATION No. 00000392 issued on June 15, 2007) 
revealed rapidly progressing de-bonding which may be due to water that may have entered from the 
crack that was detected in the leading edge stainless steel protective strip.  
If this de-bonding remains undetected, it can, in time, cause the loss of the main rotor blade stainless 
steel protective strip, and vibrations induced by the weight unbalance may compel the pilot to land 
immediately. 
 
Pending complementary examinations, EUROCOPTER reduced the interval: 
- For the visual check for de-bonding and/or cracks which may allow water to enter, 
then, 
- For the tapping test of de-bonded and/or cracked areas identified beforehand, in order to monitor the 
progress of the de-bonding. 
 
Revision 1: 
Initially, EUROCOPTER stipulated that the main rotor blades were to be removed  
to perform the visual check and the tapping test on the leading edge stainless steel protective strip, 
scheduled at 85 flying hours, 
EUROCOPTER is aware of the operational difficulty that may be caused by this task and therefore 
conducted the necessary tests and checks to modify the operational procedure. 
Consequently, EUROCOPTER now authorizes the performance of the required checks without 
removal of the main rotor blades. 
 
The criteria currently defined in the maintenance documentation are unchanged.  
 
EUROCOPTER rendered compliance with this ALERT SERVICE BULLETIN mandatory. 
 
Revision 2: 
The purpose of Revision 2 of this ALERT SERVICE BULLETIN is to extend the effectivity to main rotor 
blade part numbers 332A11.0050.02 and 332A11.0055.02 following MOD 0740714. 
 
NOTE  
 
The purpose of MOD 0740714 is to replace the current 
stainless steel tip cap leadi ng edge protection on the blade 
with a Nickel-Cobalt tip cap leading edge protection.  This 
modification creates new blade P/Nos. 
 
Revision 2 does not affect compliance with Revision 1 of this ALERT SERVICE BULLETIN. 
 
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.

### Page 4

T.F.S. No. 00000745 
      Page 4/14 
2013.04.22 
 
 
 
1.E. COMPLIANCE  
 
1.E.1. Compliance at the works 
 
1.E.1.a. On helicopters: Comp ly with paragraph 1.E.2.a.  
 
1.E.1.b. On non-installed equipment: Not applicable. 
 
1.E.2. Compliance in operation: By the operator: 
 
1.E.2.a. On helicopters / installed equipment:  
 
On main rotor blades with P/Nos. 332A11.0050.00 and 332A11.0055.00: 
 
- Comply with paragraph 2.B. within 15 flying hours following receipt of Revision 0 of this ALERT 
SERVICE BULLETIN, issued on June 28, 2007, and then interpret the results according to the 
paragraph below. 
 
On main rotor blades with P/Nos. 332A11.0050.02 and 332A11.0055.02: 
 
- Comply with paragraph 2.B. within 15 flying hours following receipt of Revision 2 of this ALERT 
SERVICE BULLETIN, issued on the date indicated at the foot of the page, and then interpret the 
results according to the paragraph below. 
 
Interpretation of results: 
 
1) If there is no crack, no cut, no open and no blind de-bonding: 
 . comply with paragraph 2.B. at intervals not exceeding 85 flying hours. 
 
2) If there is open de-bonding within the permissible criteria inside area D (see Figure 1): 
. comply with paragraph 2.B. at intervals not exceeding 85 flying hours.  
 
3) If there is a crack and/or a cut and/or open de-bonding within the permissible criteria 
 outside area D (see Figure 1): 
. comply with paragraph 2.B.2.b) and/or 2.B.2.c) and/or 2.B.2.d) at intervals not exceeding  
 15 flying hours. 
 
1.E.2.b. On non-installed equipment:   
 
 On main rotor blades listed in paragraph 1.A.1., having logged flying hours: 
 
 - Comply with paragraph 2.B. before installation on a helicopter.

### Page 5

T.F.S. No. 00000745 
      Page 5/14 
2013.04.22 
 
 
 
1.F. APPROVAL 
 
Approval is limited to civil version helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in Revision 0 of this ALERT SERVICE BULLETIN was approved  
on June 28, 2007 under the authority of EASA Design Organization Approval No. 21J.056. 
 
The technical information contained in Revision 1 of this ALERT SERVICE BULLETIN was approved  
on July 27, 2007 under the authority of EASA Design Organization Approval No. 21J.056. 
 
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved  
on April 22, 2013 under the authority of EASA Design Organization Approval No. 21J.056 for 
helicopters of civil versions subject to an Airworthiness Certificate. 
 
For the French Government helicopters, as the content of this ALERT SERVICE BULLETIN is strictly 
identical to ALERT SERVICE BULLETIN EC225 No. 05A010 of the civil version, the technical 
information contained in this ALERT SERVICE BULLETIN Revision 2 was approved  
on April 22, 2013 under the prerogatives of the recognition of design capability FRA21J-002-DGA. 
 
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved  
on April 22, 2013 by the EUROCOPTER Airworthiness Department for export military versions. 
 
 
1.G. MANPOWER 
 
Qualification: Mechanic. 
Time for one main rotor blade: Approximately 1 hour to comply with paragraph 2.B. 
 
 
1.H. WEIGHT AND BALANCE  
 
Not applicable. 
 
 
1.I. EFFECT ON ELECTRICAL LOADS 
 
Not applicable. 
 
 
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE 
 
Not applicable.

### Page 6

T.F.S. No. 00000745 
      Page 6/14 
2013.04.22 
 
 
 
1.K. REFERENCES 
 
Aircraft Maintenance Manual (MMA), Tasks: 62-10-00-061 – 62-10-00-211. 
 
 
1.L. OTHER DOCUMENTS CONCERNED  
 
Not applicable. 
 
 
1.M. TOOLING CONCERNED 
 
 Not applicable. 
 
 
1.N. INTERCHANGEABILITY AND MIXABILITY OF PARTS  
 
Not applicable.

### Page 7

T.F.S. No. 00000745 
      Page 7/14 
2013.04.22 
 
 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
 
2.A. GENERAL 
 
The operational procedure given in paragraph 2.B. is described for one main rotor blade and must be 
applied to the 5 main rotor blades. 
 
 
2.B. OPERATIONAL PROCEDURE 
 
2.B.1. Preliminary steps 
 
- Open the sliding cowling and the engine cowlings. 
- Move the main rotor blade to be checked to the right three-quarter forward position with respect to 
the aircraft centerline (see Figure 4). 
- Apply the rotor brake. 
- Position a maintenance platform along the blade leading edge side. 
- When performing the tapping test on the blade leading edge stainless steel protective strip: 
. on the blade pressure face side, support the main rotor blade tip without lifting it, 
. on the suction face side, lift the main rotor blade over approximately 75 centimeters at the blade 
tip. 
 
NOTE 
 
To support and lift the blade, make two wooden supports 
locally (one for the blade pressure face, and one for the blade 
suction face, see Figure 3). Put these supports at the blade 
tip, at the end of the main blade section (see Figure 3). 
 
2.B.2. Visual check and tapping test of the main ro tor blade leading edge stainless steel protective strip 
 
- Carry out a visual check and a tapping test on the leading edge stainless steel protective strip. 
 
. If there is no crack, no cut and no de-bonding: 
- Leave as is. 
- Return the helicopter to flight configuration in compliance with paragraph 2.B.3. and comply with 
the instructions of paragraph 1.E.2.a.1. 
 
a) If there is blind de-bonding: 
 
- Make sure that the de-bonded surface area is within the permissible criteria defined in MMA 
Task 62-10-00-211. 
 
- If the de-bonded surface area is within the permissible criteria: 
. Return the helicopter to flight configuration in compliance with paragraph 2.B.3. and comply 
with the instructions of paragraph 1.E.2.a.1. 
 
- If the de-bonded surface area is beyond the permissible criteria:  
. Remove the main rotor blade in accordance with Sub-Task 62-10-00-031-001 of MMA 
Task 62-10-00-061. 
. Remove the blade from service before resuming flights.

### Page 8

T.F.S. No. 00000745 
      Page 8/14 
2013.04.22 
 
 
 
b)  If there is open de-bonding: 
 
- Make sure that the detected de-bonding is wi thin the permissible criteria defined in MMA 
 Task 62-10-00-211. 
 
. If the de-bonded surface area is within the permissible criteria: 
- And this surface area is located inside area D at the end of the blade main section, on the blade 
tip cap side (see area D Figure 1), return the helicopter to flight configuration in compliance with 
paragraph 2.B.3. and comply with the instructions of paragraph 1.E.2.a.2. 
 
- And this surface area is located outside area D (see area D Figure 1), return the helicopter to 
flight configuration in compliance with paragraph 2.B.3., then, every 15 flying hours, carry out a 
tapping test limited to the detected de-bonded surface area, in order to monitor its behavior. 
 
. If the de-bonded surface area is beyond the permissible criteria: 
- Remove the main rotor blade in accordance with Sub-Task 62-10-00-031-001 of MMA 
Task 62-10-00-061. 
- Remove the blade from service before resuming flights. 
 
c) If there is a cut in the blade root polyure thane protective strip (see Figure 2, Area A): 
 
- Carry out a tapping test of the area. 
 
. If there is no de-bonding: 
- Return the helicopter to flight configuration in compliance with paragraph 2.B.3., then, 
. every 15 flying hours, on the blade installed on the helicopter, carry out a tapping test on 
the blade leading edge stainless steel strip in the blade root area, in the stainless steel 
leading edge / neoprene junction area, in order to make sure that there is no de-bonding. 
 
. If there is de-bonding, comply with paragraph 2.B.2.b. 
 
d) If there is a crack in the blade leading edge: 
 
- Make sure that the crack is within the perm issible criteria defined in MMA Task 62-10-00-211. 
 
. If the crack is within the permissible criteria: 
- Return the helicopter to flight configuration in compliance with paragraph 2.B.3., then, 
. every 15 flying hours, perform a tapping test in the immediate vicinity of the crack to make 
sure that there is no de-bonding.  
. If there is de-bonding, comply with paragraph 2.B.2.b). 
 
 
. If the crack is beyond the permissible criteria: 
- Remove the main rotor blade in accordance with Sub-Task 62-10-00-031-001 of MMA 
Task 62-10-00-061. 
- Remove the blade from service before resuming flights.

### Page 9

T.F.S. No. 00000745 
      Page 9/14 
2013.04.22 
 
 
 
NOTE 
 
Send the results of the check of the main rotor blades, 
indicating their serial number and that of the 
helicopter, to:  
Etablissement de LA COURNEUVE  
For the attention of Mr. Olivier TILLIER  
2 à 20 Av Marcel Cachin 
93123 LA COURNEUVE Cedex 
France  
(Fax: +33(0)1.49.39.41.70) 
 
 
2.B.3. Final steps 
 
- Where necessary, install the blade as per Sub-Task 62-10-00-431-001 of MMA Task 62-10-00-061. 
- Remove the maintenance platform from the main rotor blade. 
- Close the engine cowlings and the sliding cowling. 
 
 
2.C. IDENTIFICATION 
 
Record initial compliance with this ALERT SERVICE BULLETIN in the Log Card (FM) of the main rotor 
blade. 
 
 
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS 
 
Not applicable.

### Page 10

T.F.S. No. 00000745 
      Page 10/14 
2013.04.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 1 
 
 
 
 
Area D

### Page 11

T.F.S. No. 00000745 
      Page 11/14 
2013.04.22 
 
 
 
332A11.0055.00 
332A11.0055.02 
 
 
 
 
 
 
 
 
 
 
 
 
 
332A11.0050.00 
332A11.0050.02 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2 
Area A
Area A

### Page 12

T.F.S. No. 00000745 
      Page 12/14 
2013.04.22 
300 mm
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 3 
 
 
Height of the Support 
 
- Blade pressure face: H 
- Blade suction face:  H + 0.75 meters 
 
Note: H = Height depending on the local access 
equipment 
Blade pressure face 
Support seating zone 
H

### Page 13

T.F.S. No. 00000745 
      Page 13/14 
2013.04.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4 
 
 
Check on the blade pressure face 
Check on the blade suction face 
Support the blade but do 
not lift it
Lift the blade by  
0.75 meters 
Maintenance platform

### Page 14

T.F.S. No. 00000745 
      Page 14/14 
2013.04.22 
 
 
 
3. MATERIAL INFORMATION  
 
3.A. MATERIAL: COST – AVAILABILITY 
 
For any information contact the Customer Service Sales Department. 
 
 
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT  
 
Not applicable. 
 
 
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER / ENGINE / COMPONENT 
 
Not applicable. 
 
 
3.D. PROCUREMENT CONDITIONS  
 
Order the required quantity (unless otherwise specified) 
 
from 
 
EUROCOPTER 
Etablissement de La Courneuve 
Direction VENTES Service Client (S.V.) Fax: +33(0)1 49 34 41 70 
93123 LA COURNEUVE 
FRANCE 
NOTE 1 
 
For ALERT SERVICE BULLETINS, order by: 
Telex: HELICOP 410 969F 
Fax: +33 (0)4 42 85 99 96 
 
 
NOTE 2 
 
On the purchase order, please specify 
the mode of transport, the destination 
and the serial numbers of the helicopters  
to be modified. 
 
 
4. APPENDIX 
  
 Not applicable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
