# Eurocopter Emergency Alert Service Bulletin 25A085

Copy: No revision named ("U.S. DOT/FAA - Eurocopter EASB 25A085"), 18 pages: PDF https://openairdocs.org/files/sha256/4c/f9/4cf957544ae1c2df6b6600e136b1f533faa634bbb16c464f4f5d4b98228230ba; text https://openairdocs.org/service-documents/airbus-helicopters/25a085/file/4cf957544ae1.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2009-0195; AD 2009-06-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 25A085
- Page: https://openairdocs.org/service-documents/airbus-helicopters/25a085

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2009-06-01](https://openairdocs.org/ad/2009-06-01.md), effective Mar 31, 2009: No revision named

## Text (18 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2009-0195; AD 2009-06-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
EUROCOPTER
DIRECTION TECHNIQUE SUPPORT
13725 MARIGNANE CEDEX FRANCE
EMERGENCY
ALERT SERVICE BULLETIN
DAUPHIN  NUMBER  VERSIONS
EC155  25A085  Civil:  B,B1
SUBJECT: EQUIPMENT AND FURNISHINGS
Electrical Bonding of the Hoist Cut-Off Connector
REVISION No.
_ DATE OF APPROVAL  DATE OF ISSUE
Revision O  On: June 1$, 2007  2007.06.01
Approved under EASA DOA No. 21J.056  Page 1/13
2007.06.01

### Page 2 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters / Installed Equipment
Helicopters fitted with the optional equipment OP 45C07 (fixed parts of the hoist installation) whose Serial
Number (S/N) is strictly less than 6763.
1.A.2. Non-Installed Equipment
Not applicable.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Preventing short-circuits in hoist cut-off connector "24 Delta".
This ALERT SERVICE BULLETIN will form the subject of an EASA Airworthiness Directive.
1.D. DESCRIPTION
The occurrence of a short-circuit in hoist connector "24 Delta", with the hoist removed from the aircraft, has
been reported to EUROCOPTER.
The short-circuit heated the paint on the cooler support cowling at hoist cut-off connector "24 Delta" and
set it on fire.
As crews have no detection or display means for this short-circuit, EUROCOPTER renders compliance
with this ALERT SERVICE BULLETIN mandatory
This ALERT SERVICE BULLETIN requires the following procedures to be applied, according to the
helicopter configuration:
- Orientating the fixed connector.
- Connecting or disconnecting the hoist power cable.
- Installing an electrical bonding braid.
1.E. COMPLIANCE
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.
1.E.1. Compliance at the Works
1.E.1.a. On Helicopters: Comply with paragraphs 2.B.2.a and 2.B.2.c before delivery.
1.E.1.b. On Non-Installed Equipment: Not applicable.
1.E.2. Compliance in Operation: By the operator.
Approved under EASA DOA No. 21J.056  Page 2/13
2007.06.01

### Page 3 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
1.E.2.a. On Helicopters / Installed Equipment
Helicopters that do not embody MOD 0745C82:
No later later than within 7 days after receipt of this ALERT SERVICE BULLETIN, issued on the date
specified in the page footer, comply with the following paragraphs:
- 2.B.2.a (Orientating the fixed connector).
- 2.B.2.b (Disconnecting the hoist power cable) if the hoist is not installed.
No later than within three months after receipt of this ALERT SERVICE BULLETIN, issued on the date
specified in the page footer, comply with paragraph 2.B.2.c (Installing the electrical bonding braid).
Pending compliance with paragraph 2.B.2.c:
- Whenever the hoist is installed, connect the power cable in compliance with paragraph 2.B.2.b.
- Whenever the hoist is removed, disconnect the power cable in compliance with paragraph 2.B.2.b.
Helicopters that embody MOD 0745C82:
No later than within 7 days after receipt of this ALERT SERVICE BULLETIN, issued on the date
specified in the page footer, comply with paragraph 2.B.2.a.
1.E.2.b. On Non-Installed Equipment
Not applicable.
1.F. APPROVAL
Approval is limited to civil version helicopters subject to an Airworthiness Certificate.
1.F.1 Approval of the Modifications
The information or instructions refer to MOD 0745C82 which was approved on June 1st  , 2007.
1.F.2 Approval of the Service Bulletin
The technical information contained in this ALERT SERVICE BULLETIN was approved
on June 1st  •, 2007 under the authority of EASA Design Organisation Approval No. 21J.056.
1.G. MANPOWER
Qualification: 1 mechanic.
Time for the operations: Approximately 1 hour and 30 minutes to install the electrical bonding braid.
1 hour and 30 minutes to disconnect the hoist power cable.
1.H. WEIGHT AND BALANCE
Not applicable.
Approved under EASA DOA No. 21J.056  Page 3/13
2007.06.01

### Page 4 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
1.I. EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE
Not applicable.
1.K. REFERENCES
The following documents are necessary for compliance with this ALERT SERVICE BULLETIN:
AMM: 24-32-01-061: Removal/Installation of electrical master box 2 Alpha.
AMM: 24-61-01-061: Removal/Installation of the circuit-breaker panel.
AMM: 24-00-00-911: General safety instructions related to electrical power.
MTC: 20.02.07.402: Bonding points on metal structures.
MTC: 20.02.07.401: Bonding procedure.
MTC: 20.07.03.406: Instructions applicable when working on aircraft electrical power systems.
MTC: 20.02.05.404: Assembling by bolts and nuts.
MTC: 20.05.01.221: Sealing compound PR 1436 GS.
1.L. OTHER DOCUMENTS CONCERNED
Not applicable.
1.M. TOOLING CONCERNED
Not applicable.
1.N. INTERCHANGEABILITY OR MIXABILITY OF PARTS
Not applicable.
Approved under EASA DOA No. 21J.056  Page 4/13
2007.06.01

### Page 5 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
2. ACCOMPLISHMENT INSTRUCTIONS
2.A. GENERAL
- Read and comply with the instructions for removal/installation of electrical master box "2 Alpha" as per
AMM Task 24-32-01-061.
- Read and comply with the general safety instructions related to electrical power as per AMM
Task 24-00-00-911.
- Read and comply with the instructions for removal/installation of the circuit-breaker panel as per AMM
Task 24-61-01-061.
- Read and comply with the instructions related to electrical bonding of metal structures as per MTC Work
Card 20.02.07.402
- Read and comply with the electrical bonding procedures as per MTC Work Card 20.02.07.401.
- Read and comply with instructions related to assembly by nuts and bolts as per MTC Work Card
- Read and comply with the instructions related to sealing compound application as per MTC Work Card
20.05.01.221.
2.B. OPERATIONAL PROCEDURE
2.B.1. Preliminary Steps
- Disconnect all electrical power sources as per MTC Work Card 20.07.03.406.
- Install the electrical power inhibit provisions on the helicopter.
- Set up appropriate access equipment.
- Open the RH engine cowling to gain access to hoist fixed power connector "24 Delta".
- Remove the oil cooler air inlet fairing to gain access to the screw of ground point "28N".
- Open the radome to gain access to electrical master box "2 Alpha".
2.B.2. Procedure
2.B.2.a. Orientating the Fixed Connector (Figure 1):
. If the large contacts of connector "24 Delta" are positioned aft (Figure 1, item W), leave as is.
. If the large contacts of connector "24 Delta" are not positioned aft, orientate connector "24 Delta" as
shown on Figure 1 (item W).
2.B.2.b. Disconnecting/Connecting the Power Cable (Figures 2, 3, 4, and 5):
. Remove the circuit-breaker panel as per AMM Task 24-61-01-061 (Figure 2).
Remove cover (h) to gain access to the fuse terminal block as per AMM Task 24-32-01-061 (Figure 4).
• In electrical master box "2 Alpha", disconnect hoist power wire "2ME40E" at 130A-rated fuse (g)
(Figures 3, 4, and 5).
. Insulate the hoist power wire.
Immobilize the hoist power wire.
. Retorque the fuse holder, with the fuse in place, as per AMM Task 24-32-01-061.
. Install cover (h) as per AMM Task 24-32-01-061.
. Install the circuit-breaker panel as per AMM Task 24-61-01-061.
To connect the hoist power cable, proceed in the reverse order.
Approved under EASA DOA No. 21J.056  Page 5/13
2007.06.01

### Page 6 (OCR)

eurocopter  an EADS Company
T.F.S. No. 00000378
2.B.2.c. Installing the Electrical Bonding Braid (Figures 6, 7, 8, and 9)
- Remove screw (a), nut (b), and washer (c) (Figure 6).
- Discard screw (a), and retain nut (b) and washer (c).
- Ensure electrical bonding as per MTC Work Cards 20.02.07.401 and 20.02.07.402.
- Install braid (4) (Figure 7) using screw (1), nut (b), and washer (c).
On ground point "28N" (Figures 8 and 9) at the 9° frame, on aircraft RH side.
- Remove the sealing compound
- Remove screw (d), nut (e), and washer (f).
- Discard screw (d) and retain nut (e) and washer (f).
- Ensure electrical bonding as per MTC Work Cards 20.02.07.401 and 20.02.07.402.
- Install braid (4) on electrical bonding point "28N" using screw (2), washer (3), braid (y), washer (f), and
- Torque as per MTC Work Card 20.02.05.404 (Figures 8 and 9).
- Apply sealing compound (5).
2.B.3. Final Steps
- Close the radome.
- Install the oil cooler air inlet fairing.
- Close the engine cowling.
- Remove the access equipment.
- Remove the electrical power inhibit provisions from the helicopter.
- Reconnect all the electrical power sources as per MTC Work Card 20.07.03.406.
2.C. IDENTIFICATION
Record initial compliance with this ALERT SERVICE BULLETIN in the helicopter documents.
Record embodiment of MOD 0745C82 in the helicopter documents after complying with paragraph
2.B.2.c. (Installing the electrical bonding braid).
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Approved under EASA DOA No. 21J. 056  Page 6/13
2007.06.01

### Page 7 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
FWD
Figure1
Orientation of the Hoist Fixed Connector.
FWD  FWD
FWD
Approved under EASA DOA No. 21J.056  Page 7/13
2007.06.01

### Page 8 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
2 Alpha
Figure 2
Location of Electrical Master Box 2 Alpha
g
Figure 3
Location of the Power Connector
Approved under EASA DOA No. 21J. 056  Page 8/13
2007.06.01

### Page 9 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
n
Figure 4
Location of the Power Connector
685
ENG DECK  24DEL
281
F2PCO
2ME39NE DG 04
2ME 40E - DG 04  TAJ
NOSE CEFECTRICAL MASTER BOX 2
SHEAT F0210DHS754-100 30
2ME 27F  GND
2ME 29E  PREAM INPUT
9  2ME 3 0E  2ME 3 1E  M  PREAM INPUT  PREAM INPUT
SEE 25.63.01.105  +28VDC
DOWN
UP
2ME 38 NE
1ME 20E
4M-J1 P1
CARGO TRANS DECK  685 ENG DECK
665 685
Figure 5
Wiring Diagram
Approved under EASA DOA No. 21J.056  Page 9/13
2007.06.01

### Page 10 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
244
Figure 6 (Pre MOD 0745C82)
Fixed Power Connector for the Hoist
C
4
244
Figure 7 (Post MOD 0745C82)
Fixed Power Connector for the Hoist
Approved under EASA DOA No. 21J.056  Page 10/13
2007.06.01

### Page 11 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
244
N8Z
FIgure 8 Pre MOD 0745C82
-lectrical Bonding Poin
28N
2
Figure 9 (Post MOD 0745C82)
Electrical Bonding Point
Approved under EASA DOA No. 21J.056  Page 11/13
2007.06.01

### Page 12 (OCR)

eurocopter  an EADS Company
T.F.S. No. 00000378
3. MATERIAL INFORMATION
3.A. MATERIAL: COST - AVAILABILITY
3.A.1. Cost
Kits and/or components will be delivered free of charge on Operator's order within 3 months following
receipt of this ALERT SERVICE BULLETIN, issued on the date specified in the page footer.
3.A.2. Availability
Kits and/or components will be delivered on Operator's order.
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT
Not applicable.
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER / ENGINE / COMPONENT
3.C.1. Kit(s) or Component(s) to be Ordered for One Helicopter or One Assembly
Material Part Number  Qty  Ite  Key Word  Former Part Number  Instructions
m
365A08-3275-0071  1  Kit including:
22272BC040014L  1  1  Screw
22208BC060016L  2  Screw
23116AG040LE  Washer
993105-304-6  4  Electrical bonding
braid
3.C.2. Items) to be Ordered Separately
Not applicable.
3.C.3. Products) to be Ordered Separately
Material Part Number  Qty.  Item  Key Word
PR1436GS  A/R  5  PR1436GS
The products identified by an asterisk "*" or required for compliance with the tasks and/or work cards listed
in paragraph 1.K. can be ordered from the company INTERTURBINE
Website: http://www.itlogistics.de
Telephone: +49.41.91.809.300
AOG  : +49.41.91.809.444
Approved under EASA DOA No. 21J.056  Page 12/13
2007.06.01

### Page 13 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000378
3.D. PROCUREMENT CONDITIONS
Order the required quantity (unless otherwise specified)
from
EUROCOPTER
Etablissement de Marignane
Direction Ventes et Relations Client
ECR
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4 42 85 99 96
NOTE 2
On the purchase order, always specify the mode of transport, the destination,
and the serial numbers of the aircraft to be modified.
4. APPENDIX
Not applicable.
Approved under EASA DOẠ No. 21J.056  Page 13/13
2007.06.01

### Page 14

(No text on this page.)

### Page 15 (OCR)

SA S92A-RFM-003  Part I, Section III
EMERGENCY PROCEDURES
7.0 GEAR BOX MALFUNCTIONS
Main gearbox malfunctions can be broken down into three types:
1. Lubrication failures.
2. Component failures.
3. Transmission accessory failures.
The main gearbox temperature and pressure gages, along with the main gearbox chip detection system, should give the pilot
enough information to make an informed decision if a main gearbox problem arises.
An impending gearbox failure may exhibit one or more of the following symptoms:
Chip lights from any of the main transmission modules.
Low transmission oil pressure and/or MGB OIL PRES caution.
High transmission oil temperature and/or MGB OIL HOT caution.
Increased power required at constant collective and airspeed.
Aircraft yaw kicks.
Howling, grinding, or unusual noise from the main transmission.
The presence of multiple symptoms is a very strong indicator of an impending failure. If impending failure is suspected,
the primary consideration is to land the aircraft before failure progresses to gearbox seizure or loss of drive to the main or
tail rotor. Descend to an altitude from which a landing can be quickly made with minimal power changes and fly at an
airspeed for which minimum power is required. Descent should be done at a reduced power setting, but with enough torque
to drive the transmission. Avoid rapid or frequent power changes. High temperatures or loss of lubrication may result in
loss of the main generators. The APU should be started so that the APU generator will be immediately available. A running
landing is preferred since it requires lower power and smaller power changes. A no-hover landing should be performed if
a running landing area is not available.
NOTE
The accessory, input, tail, intermediate and main gear box chip detectors
include an integral oil temperature sensor. When a sensor detects a hot
condition, the fuzz burn feature of the affected chip detector is disabled.
7.1 MAIN GEARBOX OIL SYSTEM FAILURE
Symptom:
MGB OIL PRES or MGB OIL HOT or MGB CHIP or ACC 1 CHIP or ACC 2 CHIP or MGB OIL PRES
"GEARBOX OIL PRESSURE" aural alert.
Confirming:
FAA APPROVED: MARCH 21, 2005
Revised: July 17, 2007
3-31

### Page 16 (OCR)

Part I, Section III  SA S92A-RFM-003
EMERGENCY PROCEDURES
NOTE
The confirming steps only apply to low oil pressure or high oil
temperature. There are no confirming steps for chip indications.
Main gearbox oil temperature is greater than 130°C.
WARNING
BYP must be selected within 5 seconds after the MGB OIL
PRES warning has illuminated to ensure an adequate
quantity of oil remains in the gearbox. DO NOT activate BYP
if the warning is not illuminated.
CAUTION
When the MGB BYP mode is activated by the crew, the MGB
oil temperature will increase. The temperature is expected to
increase into the red operational range, this indication
should not be considered a secondary indication for
CAUTION
The main AC generators are cooled by main gearbox oil. Loss
of cooling oil may result in mechanical failure of the genera-
tors and loss of main electrical power.
NOTE
The MGB BYPASS caution will illuminate when BYP is selected. As
the MGB oil pressure stabilizes, the switch should be left in the BYP
position. The MGB BYPASS caution and MGB OIL PRES warning
will remain on until the rotor is shut down after landing.
FAA APPROVED: MARCH 21, 2005
3-32  Revised: April 9, 2008

### Page 17 (OCR)

SA S92A-RFM-003  СS9₴Ò  Part I, Section Ill
EMERGENCY PROCEDURES
NOTE
After MGB bypass switch is activated, MGB oil pressure should
stabilize or fluctuate in the range of 5 to 25 psi. Gearbox temperature
will slowly increase into the red zone.
FAA APPROVED: MARCH 21, 2005
Revised: July 17, 2007
3-32A/(3-32B Blank)

### Page 18

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
