# Airbus Helicopters Emergency Alert Service Bulletin 53A019

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 1 ("U.S. DOT/FAA - Airbus EASB Number 53A019 Rev 1"), 15 pages: PDF https://openairdocs.org/files/sha256/dc/0b/dc0b9a3554e07a4fa219c897dbbd3cadf72f0cdfe2b2fb7003171324725f1c68; text https://openairdocs.org/service-documents/airbus-helicopters/53a019/file/dc0b9a3554e0.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0757; AD 2014-20-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- U.S. DOT/FAA - Eurocopter Emergency ASB 53A019 ("U.S. DOT/FAA - Eurocopter Emergency ASB 53A019"), 13 pages: PDF https://openairdocs.org/files/sha256/c4/0e/c40e8c9e435e39a12726b238dace97fef9babf6db98bfe522061e3995079f473; text https://openairdocs.org/service-documents/airbus-helicopters/53a019/file/c40e8c9e435e.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0086; AD 2012-02-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 53A019
- Latest revision known: 53A019, Revision 1, dated April 15, 2014 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/53a019

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2014-20-15](https://openairdocs.org/ad/2014-20-15.md), effective Oct 22, 2014: Revision 1
- [AD 2012-02-13](https://openairdocs.org/ad/2012-02-13.md), effective Feb 22, 2012: No revision named

Also cited in [1 NTSB investigation](https://openairdocs.org/service-documents/airbus-helicopters/53a019/ntsb.md).

## Text (15 pages)

Revision 1, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0757; AD 2014-20-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  EASB
EMERGENCY
ALERT SERVICE BULLETIN
SUBJECT: FUSELAGE
Check of the tail boom / Fenestron junction frame
For the attention of
CONCERNED  AIRCRAFT  NUMBER  Civil  Version(s)  Military
EC130  53A019  B4
Revision No.  Date of issue
Revision 0  2011-06-14
Revision 1  2014-04-15
Summary:
Check for cracks in the tail boom/Fenestron junction frame.
Reason for last revision:
The purpose of Revision 1 of this ALERT SERVICE BULLETIN is:
- To extend the inspection to the entire circumference of the frame.
- To cancel the instructions in this ALERT SERVICE BULLETIN for helicopters which have embodied
MOD 074609 through SB 53-024.
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Revision 0 2011-06-14  Page 1/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  EASB
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment
- Helicopters equipped with a tail boom assembly fitted with countersunk head rivets at the tail
boom / Fenestron junction on the Fenestron side, which do not embody:
. modification 073880 (Reinforcement of the tail boom / Fenestron junction),
or
. RDAS No. 350 53 522 07 or 350 53 521 10 or 350 53 524 10 or 350 53 525 10 or 350 53 526 10 or
350 53 511 11 or 350 53 512 11 or 350 53 523 11 or 350 53 504 12 or RDAS-AE11-0205 or
RDAS-AE11-0380,
or
• modification 074609 (Reinforcement of the tail boom / Fenestron junction through retrofit) (see NOTE 5).
- The helicopter equipped with tail boom assembly number TB 7377 is not concerned by the instructions of
this ALERT SERVICE BULLETIN.
NOTE 1
Refer to the aircraft individual inspection log book (MOD record) to identify the
actual configuration of the helicopter.
NOTE 2
The tail boom assemblies which are not identified by one of the above-mentioned
RDAS numbers and contain a tail boom / Fenestron junction frame riveted with
brazier head rivets on the Fenestron side, have embodied modification 073880.
NOTE 3
The RDASs are identified by the marking of their number close to the tail boom
identification label, visible from the inside of the rear cargo compartment.
NOTE 4
The tail boom assemblies which have been subject to compliance with Service
Bulletin No. 53-017 are concerned by the instructions of this ALERT SERVICE
BULLETIN, except for tail boom assembly number TB 7377.
NOTE 5
The tail boom assemblies which embody MOD 074609 (through Service Bulletin
No. 53-024) are not concerned by the instructions of this ALERT SERVICE
BULLETIN.
Revision 0 2011-06-14  Page 2/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  EASB
1.A.2. Non-installed equipment
- Tail boom assemblies fitted with countersunk head rivets at the tail boom / Fenestron junction on the
Fenestron side and which do not embody:
• modification 073880 (Reinforcement of the tail boom / Fenestron junction) (See NOTE 2),
or
. RDAS No. 350 53 522 07 or 350 53 521 10 or 350 53 524 10 or 350 53 525 10 or 350 53 526 10 or
350 53 511 11 or 350 53 512 11 or 350 53 523 11 or 350 53 504 12 or RDAS-AE11-0205 or RDAS-
AE11-0380. (See NOTE 3),
or
• modification 074609 (Reinforcement of the tail boom / Fenestron junction) (See NOTE 5).
- The tail boom assembly with part number TB 7377 is not concerned by the instructions of this ALERT
SERVICE BULLETIN.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
Revision 0 2011-06-14  Page 3/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  EASB
1.C. REASON
Revision 0:
Following the issue of Information Notice No. 2167-1-53, EUROCOPTER has received new reports of cracks
in the tail boom/Fenestron junction frame.
The cracks started in the plane of the rivet head countersinks on the RH side of the Fenestron (Detail E,
Figure 3) and spread to the web of the frame (Details C and D, Figure 2).
The examination of the parts showed that the cracks were longer than in the previous cases, questioning
easy detection of the cracks from the outside as well as the inspection interval to substantiate the strength of
the frame.
Consequently, EUROCOPTER rendered compliance with this ALERT SERVICE BULLETIN mandatory,
whose purpose was to enable a detailed visual check from the outside and inside of the frame and to
schedule its replacement if a crack is found.
Revision 1:
Airbus Helicopters has defined modification 074609, whose purpose is to limit the risk of cracks appearing on
the tail boom / Fenestron junction frame.
The purpose of Revision 1 of this ALERT SERVICE BULLETIN is to:
- inform operators that the embodiment of MOD 074609 (Service Bulletin 53-024) cancels the instructions
defined in this ALERT SERVICE BULLETIN.
- modify compliance with paragraph 1.E.2. by requesting the embodiment of MOD 074609 through Service
Bulletin 53-024 before 31/12/2017.
- To extend the inspection to the entire circumference of the frame on helicopters defined in paragraph 1.A.
Revision 1 of this ALERT SERVICE BULLETIN affects compliance with Revision 0.
1.D. DESCRIPTION
Compliance with this ALERT SERVICE BULLETIN consists in checking for cracks in the tail boom/Fenestron
junction frame.
1.E. COMPLIANCE
NOTE 6
In the following paragraphs, use the contact information below to contact the
Technical Support Department of the Customer Service:
Tel.: +33 (0)4.42.85.97.16.
Fax: + 33 (0)4.42.85.99.66.
E-mail: airframe.technical-support@eurocopter.com
NOTE 7
Airbus Helicopters reminds you that a visual check for cracks is scheduled at the
flight-related check (VLV) as per AMM Task 05-40-00,6-1 and makes it possible to
detect a crack, if any.
1.E.1. Compliance at the works
Not applicable.
Revision 0 2011-06-14  Page 4/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  EASB
1.E.2. Compliance in service
Helicopters/installed equipment: The work on the helicopter is to be performed by the operator.
a) Within 10 flying hours following receipt of Revision 0 of this ALERT SERVICE BULLETIN, issued
on 14/06/2011:
. Comply with paragraphs 3.B.1. and 3.B.2. pending compliance with paragraphs 3.B.3. and 3.B.4.
Interpretation of results following compliance with paragraphs 3.B.1.and 3.B.2.:
1) Presence of a crack entirely crossing the web (c) of frame (a) (See detail D, Figure 2):
All flights are prohibited.
For the conditions for returning the helicopter to service, contact the Customer Service Technical
Support Department (See NOTE 6).
2) Presence of a crack crossing part of the web (c) of frame (a):
All flights are prohibited except for the ferry flight not exceeding 10 flying hours.
• For the conditions for returning the helicopter to service, contact the Customer Service Technical
Support Department (See NOTE 6).
3) Presence of a crack on the outside of frame (a) and no crack in the web (c) of frame (a):
. Comply successively with paragraphs 3.B.3. (unless already carried out) and 3.B.4.
4) If no crack is found:
Flights can be continued.
. Pending compliance with paragraphs 3.B.3. and 3.B.4., comply with paragraphs 3.B.1. and 3.B.2. at
periodic intervals not exceeding 40 flying hours.
Revision 0 2011-06-14  Page 5/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 6 (OCR)

F  AIRBUS
HELICOPTERS  EASB
b) Within 110 flying hours following the last inspection without exceeding 6 months following receipt of
Revision 1 of this ALERT SERVICE BULLETIN, issued on the date indicated at the bottom of the page:
. Comply with paragraphs 3.B.3. and 3.B.4. successively.
Interpretation of results following compliance with paragraphs 3.B.3. and 3.B.4.:
1) Presence of a crack reaching the radius of frame (a) (Figure 3):
• All flights are prohibited beyond 85 flying hours following the inspection (compliance with paragraph
3.B.4. or the flight-related check (VLV)) prior to the one during which a crack, reaching the radius
of frame (a), was detected, except for the ferry flight not exceeding 10 flying hours.
. Comply with paragraph 3.B.1. at periodic intervals not exceeding 40 flying hours.
• For the conditions for returning the helicopter to service, contact the Customer Service Technical
Support Department (See NOTE 6).
2) Presence of a crack not reaching the radius of frame (a) (Figure 3):
. All flights are prohibited after 12 months from initial detection of a crack on the outside of the
frame, except for the ferry flight not exceeding 10 flying hours.
. Comply successively with paragraphs 3.B.1. and 3.B.4. at periodic intervals not exceeding 40 flying
• Inform the Customer Service Technical Support Department (See NOTE 6).
3) If no crack is found:
• Flights can be continued
. Pending compliance with Service Bulletin 53-024, comply with paragraph 3.B.4. at periodic intervals
not exceeding 100 flying hours.
. Comply with Service Bulletin 53-024 (MOD 074609) before 31/12/2017.
Revision 0 2011-06-14  Page 6/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  EASB
Key:
TO: date of receipt of this  TO: date of receipt of this  EASB Rev O  EASB Rev 1.  receipt of this ALERT SERVICE  Within 10 flying hours from  BULLETIN Revision 0 (TO)
T1: date of initial detection
of a crack on the  Check for cracks on the inside and outside
outside.  (§ 3.B.1. and 3.B.2.)
T2:  date of the inspection
prior to the one during  40 flying
which a crack, reaching  Yes  Crack?  No  hours
the radius of the frame,
No
110 flying hours //
6 months since TO
Crack on the  Crack on the
inside  outside (T1)
Yes
part of the web  Crack crossing  entirely  Crack  the outside of the  Strip the area on  the outside of the  Strip the area on
crossing  frame (§ 3.B.3)  frame (§ 3.B.3)
the web
Check stripped area  Check stripped area
PROHIBITED  except for  FLIGHT  Contact Airbus  PROHIBITED.  FLIGHT  on the outside of  frame (§ 3.B.4)  on the outside of the  frame (§ 3.B.4)  100
terry flight  ≤10 flying  Helicopters  flying  hours
hours.
Contact  Contact Airbus Helicopters  Yes= T1  Crack on the
Airbus  outside ?  No
Helicopters
Comply with SB
53-024 before
No  Does the crack on  Yes  31/12/2017
the outside reach the
radius of the frame?
Airworthiness
Directive
lifted
Check for cracks on the inside and
the outside (§ 3.B.1. and 3.B.4)  Check the inside of
the frame (§ 3.B.1)
40 flying
hours
40 flying
12 months  No  hours  Crack on the inside or
since T1?  85 flying hours since  No
T2?
Yes  FLIGHT PROHIBITED except for
ferry flight ≤10 flying hours.  es
Contact Airbus Helicopters
Revision 0 2011-06-14  Page 7/15
Revision 1  2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  EASB
Non-installed equipment:
Before installation on a helicopter, comply with paragraph 3.
1.F. APPROVAL
Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision O was approved
on June 10, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of
civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on April 08, 2014 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of
civil versions subject to an Airworthiness Certificate.
1.G. MANPOWER
Airbus Helicopters recommends that compliance with this ALERT SERVICE BULLETIN be ensured by
personnel with the following qualification:
Qualification: 1 Mechanical Engineering Technician or Aircraft Structure Technician (paragraph 3.B.)
and/or,
1 suitably trained pilot, qualified in accordance with local regulations (paragraphs 3.B.1.,
3.B.2. and 3.B.4.).
The time for the operations is given for information purposes, for a standard configuration.
Time for the operations: Approximately 10 minutes for compliance with paragraph 3.B.1.
Approximately 10 minutes for compliance with paragraph 3.B.2.
Approximately 4 hours for compliance with paragraph 3.B.3. excluding drying time.
Approximately 30 minutes for compliance with paragraph 3.B.4.
1.H. WEIGHT AND BALANCE
Not applicable.
1.. EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD
Not applicable.
Revision 0 2011-06-14  Page 8/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  EASB
1.K. REFERENCES
The following documents are necessary for compliance with this ALERT SERVICE BULLETIN.
Standard Practices Manual (MTC):
MTC: 20.02.07.403: Applying VERNELEC 43022 varnish.
MTC: 20.04.01.102: Description and use of standard cleaning products for individual parts and on aircraft.
MTC: 20.04.02.401: Stripping organic surface coatings.
MTC: 20.04.05.101: General information concerning painting means and paint touch-ups.
MTC: 20.04.05.402: EPOXY primer P05-P20 scheme.
Aircraft Maintenance Manual (AMM):
AMM: 55-11-00,4-1: Removal/Installation - Horizontal stabilizer
1.L. DOCUMENTS AFFECTED
Modification 074609 of this ALERT SERVICE BULLETIN will be integrated into the following manual:
- MSM.
These documents will be issued subsequently.
1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS
Not applicable.
Revision 0 2011-06-14  Page 9/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  EASB
2. MATERIAL INFORMATION
2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
Not applicable.
2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT
Not applicable.
2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT
Products to be ordered separately:
Refer to the Work Cards and Tasks specified in this ALERT SERVICE BULLETIN and the list below:
Item
Designation  Qty  Product P/N  No.
Primer P05  A/R  DHS186-111.20  CM 487  1
Primer P20  AR  DHS186-111.40  CM 488  2
VERNELEC varnish  AR  ECS2228.10  CM 514  3
The products can be ordered separately from the INTERTURBINE AVIATION LOGISTICS company.
Website:  http://www.interturbine.com
Telephone:  +49.41.91.809.300
AOG:  +49.41.91.809.444
2.D. MATERIAL TO BE RETURNED
Not applicable.
Revision 0 2011-06-14  Page 10/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  EASB
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
Read and comply with the general instructions concerning painting means and paint touch-ups as per MTC
Work Card 20.04.05.101.
3.B. OPERATIONAL PROCEDURE
3.B.1. Inspection of the RH side of the tail boom/Fenestron junction frame from the inside (Figures 1 and 2)
- Check that there is no crack in the web (c) of frame (a) on the RH side (Details C and D, Figure 2) using a
light source positioned in front of the opening of the drive shaft tube and by looking through the yaw control
opening in the Fenestron (Detail B, Figure 1).
CAUTION
FOR THIS INSPECTION, THE SURFACE OF THE
FRAME MUST BE CLEAN.
- If necessary, clean the web (c) of junction frame (a):
. Remove the horizontal stabilizer as per AMM Task 55-11-00,4-1.
. Clean junction frame (a) as per MTC Work Card 20.04.01.102.
. Install the horizontal stabilizer as per AMM Task 55-11-00,4-1.
- Interpret the results in accordance with paragraph 1.E.2. a).
3.B.2. Inspection of the RH side of the tail boom/Fenestron junction frame from the outside before stripping
(Figures 1 and 2)
- Check that there is no crack on the external surface of junction frame (a) (Detail A, Figure 1).
- Interpret the results in accordance with paragraph 1.E.2. a).
3.B.3. Stripping the entire circumference of the tail boom/Fenestron junction frame (Figure 3)
- Remove the cowling (b).
- Strip the two rows of rivets over the circumference of the junction frame on the Fenestron side up to the tail
boom coating, as per Detail E and as per MTC Work Card 20.04.02.401:
. over the visible width of 45 mm (1.771 in.) from the cowling (b).
- Apply a coat of primer (1) or (2) to the stripped area as per MTC Work Card 20.04.05.402.
- Apply varnish (3) to the stripped area as per MTC Work Card 20.02.07.403.
- Install the cowling (b)
3.B.4. Inspection of the entire circumference of the tail boom/Fenestron junction frame from the outside after
stripping (Figure 3)
- Remove the cowling (b).
- Check that there are no cracks in the area stripped in accordance with paragraph 3.B.3.
- Interpret the results as per paragraph 1.E.2. b).
- Install the cowling (b).
Revision 0 2011-06-14  Page 11/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  EASB
3.C. IDENTIFICATION
Identification of this document:
Record initial compliance with this ALERT SERVICE BULLETIN in the helicopter documents.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2011-06-14  Page 12/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  EASB
¢ C
Figure 1
Revision 0 2011-06-14  Page 13/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  EASB
C
Figure 2
Revision 0 2011-06-14  Page 14/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  EASB
radius of frame (a)
E
45 mm (1.771 in.)
b
Area to be stripped
over the entire
circumference of the
frame
DETAIL of the Area to be stripped
a
Figure 3: shows the partial stripping of the frame
Revision 0 2011-06-14  Page 15/15
Revision 1 2014-04-15  This document is available on the Internet: www.airbushelicopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
