# Eurocopter Emergency Alert Service Bulletin 63A011

Copy: No revision named ("U.S. DOT/FAA - Eurocopter Emergency ASB 63A011 63-0017 65.47 65-03"), 14 pages: PDF https://openairdocs.org/files/sha256/1e/c8/1ec8ea32d499d8b9e117fc6728836b5563064992bee98159b24752647e11d1ca; text https://openairdocs.org/service-documents/airbus-helicopters/63a011/file/1ec8ea32d499.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0632; AD 2012-26-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 63A011
- Page: https://openairdocs.org/service-documents/airbus-helicopters/63a011

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2012-26-10](https://openairdocs.org/ad/2012-26-10.md), effective Feb 13, 2013: No revision named
- [AD 2012-21-09](https://openairdocs.org/ad/2012-21-09.md), effective Nov 7, 2012: No revision named

## Text (14 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0632; AD 2012-26-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 1/14
  2008.05.07
  
 
EUROCOPTER  
DIRECTION TECHNIQUE SUPPORT 
13725 MARIGNANE  CEDEX FRANCE 
 
EMERGENCY 
ALERT SERVICE BULLETIN 
DAUPHIN NUMBER VERSIONS 
Civil:  N,N1,N2,N3. AS 365 63.00.17 Military: F,Fs,Fi,K. 
  AS 565 63.00.12 Military: AA,MA,MB,SA,SB,UB
Civil: B,B1 EC 155 63A011   
Civil: G1 SA 366 65.03 Military: GA 
Civil: C,C1,C2,C3 SA 360/SA 365 65.47   
 
 
 
 
SUBJECT:  MAIN ROTOR DRIVE  
 
Check of the Main Gearbox Casing (to make sure that there is no corrosion in 
the area of the servo-control attachment fittings)  
 
 
REVISION No. DATE OF APPROVAL DATE OF ISSUE 
   
   
Revision 0 On: May 06, 2008 2008.05.07 
   
   
   
   
   
 
 
 
This document is available on the internet : www.eurocopter.com/techpub

### Page 2

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 2/14
  2008.05.07
  
 
 
 
1. PLANNING INFORMATION  
 
1.A. EFFECTIVITY 
 
1.A.1. Helicopters / Installed equipment: 
 
Main Gearboxes (MGBs), all part numbers: 
 
- New MGBs delivered until December 5, 2007 (inclusive), or installed on new helicopters delivered until 
December 5, 2007 (inclusive) (refer to the conformity certificate of the helicopter), 
- MGBs newly overhauled or repaired before September 30, 2008. 
 
1.A.2. Non-installed equipment 
 
Main Gearboxes (MGBs), all part numbers: 
 
- New MGBs delivered until December 5, 2007 (inclusive), 
- MGBs newly overhauled or repaired before September 30, 2008. 
 
 
NOTE 1 
 
 
This ALERT SERVICE BULLETN does not apply to: 
- New MGBs delivered after December 5, 2007 
 (date recorded on the equipment log card). 
- MGBs newly overhauled or repaired after  
September 30, 2008 (date recorded on the equipment 
log card). 
- MGBs installed on new helicopters (refer to the 
conformity certificate of the helicopter) delivered after 
December 5, 2007. 
 
 
1.B. ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C. REASON 
 
To make sure that there is no corrosion in the lower area located between the two Main Gearbox casing 
servo-control attachment ribs if there is a bead of PR sealing compound on the lower part of the servo-
control attachment fittings. 
 
This ALERT SERVICE BULLETIN will form the subject of an DGAC Airworthiness Directive.

### Page 3

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 3/14
  2008.05.07
  
 
 
 
1.D. DESCRIPTION 
 
EUROCOPTER has received some reports of atmospheric corrosion on the Main Gearbox casing 
lower area, between the two servo-control anchoring fitting attachment ribs (see Figure 1).  
The examinations and analyses of this occurrence have revealed that this corrosion results from 
an area trapped under the anchoring fittings.  This trapped area is associated with a bead of PR 
sealing compound on the lower part of the fitting/casing attachment. 
 
This occurrence of corrosion weakens this area of the casing and could, in time, lead to crack 
initiation and crack growth which could cause this area to fail and lead to the loss of control of the 
helicopter. 
 
Consequently, EUROCOPTER renders compliance with the measures defined in this ALERT 
SERVICE BULLETIN, mandatory. 
 
 
1.E. COMPLIANCE  
 
1.E.1. Compliance at the works 
 
1.E.1.a. On helicopters / installed equipment: Not applicable. 
 
1.E.1.b. Non-installed equipment: Not applicable. 
 
1.E.2. Compliance in operation: By the operator. 
 
1.E.2.a. On helicopters / installed equipment: 
 
Comply with paragraph 2.B.2. at the latest within 15 flying hours following receipt of this ALERT 
SERVICE BULLETIN, issued on the date indicated at the foot of the page: 
 
- If there is no PR sealing compound on any of the lower parts of the MGB servo-control anchoring 
fittings: 
.  leave as is, 
. Return the helicopter to flight condi tion in compliance with paragraph 2.B.4. 
 
- If there is a bead of PR sealing compound on the lower part of at least one MGB 
servo-control anchoring fitting: 
 
. Contact the Customer Service Technical Support O perations Department (STVM) to inform it that 
you have discovered a bead of PR sealing compound on the lower part  of the attachment fittings, 
by: 
 Tel: +33 (0)4.42.85.99.67 
 Fax: +33 (0)4.42.85.99.66.  
Email : Dyncomp.technical-support@eurocopter.com 
 
. Comply with paragraph 2.B.3. (See NOTE 3 of paragraph 1) 
Or 
. Leave as is and,  
. Return the helicopter to flight condi tion in compliance with paragraph 2.B.4. 
then: 
- Comply with paragraph 2.B.3. according to the conditions specified in paragraphs 1.E.2.a.1.  
or 1.E.2.a.2.

### Page 4

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 4/14
  2008.05.07
  
 
 
 
NOTE 2 
 
For MGBs for which the history of the operating 
conditions cannot be traced back, comply with the 
instructions given in paragraph 1.E.2.a.1. 
 
1.E.2.a.1. For MGBs installed since new or last complete overhaul, on helicopters that have been operated in 
one of the following operating conditions, regardless of the time spent: 
- Helicopters based onboard ship and operated offshore 
- Helicopters operated less than 1 kilometer off the coast 
- Helicopters operated at low attitude (less than 1000 feet) over the sea 
and 
a) which have logged less than 30 months since new or last complete overhaul: 
  
- comply with paragraph 2.B.3. at the latest when the MGB reaches 33 months since new or last 
 complete overhaul of the MGB: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
- comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 33 months since new 
or last complete overhaul of the MGB. 
 
b) which have logged between 30 and 33 months since new or last complete overhaul: 
  
- comply with paragraph 2.B.3. at the latest when the MGB reaches 33 months since new or last 
 complete overhaul of the MGB: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
- comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 33 months since new 
or last complete overhaul of the MGB. 
 
or 
 
- comply with paragraph 2.B.3. within 3 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 55 flying hours: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. within 3 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 55 flying hours.

### Page 5

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 5/14
  2008.05.07
  
 
 
 
c) which have logged more than 33 months since new or last complete overhaul: 
 
-comply with paragraph 2.B.3. within 3 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 55 flying hours: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
-comply with paragraph 2.B.3.b. within 3 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 55 flying hours. 
 
 
1.E.2.a.2. For MGBs which have never been installed since new or last complete overhaul, on helicopters that 
have been operated in one of the following operating conditions: 
- Helicopters based onboard ship and operated offshore 
- Helicopters operated less than 1 kilometer off the coast 
- Helicopters operated at low attitude (less than 1000 feet) over the sea 
and 
 
a) which have logged less than 54 months since new or last complete overhaul: 
  
- comply with paragraph 2.B.3. at the latest when the MGB reaches 60 months since new or last 
 complete overhaul of the MGB: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 60 months since new 
or last complete overhaul of the MGB.

### Page 6

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 6/14
  2008.05.07
  
 
 
 
b) which have logged between 54 and 60 months since new or last complete overhaul: 
  
- comply with paragraph 2.B.3. at the latest when the MGB reaches 60 months since new or last 
 complete overhaul of the MGB: 
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 60 months since new 
or last complete overhaul of the MGB. 
 
or 
 
- comply with paragraph 2.B.3. within 6 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 110 flying hours:  
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. within 6 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 110 flying hours.  
 
c) which have logged more than 60 months since new or last complete overhaul: 
 
- comply with paragraph 2.B.3. within 6 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 110 flying hours.  
 
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings: 
 - comply with paragraph 2.B.3.a. 
 
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring 
fittings: 
- comply with paragraph 2.B.3.b. within 6 months following receipt of this ALERT SERVICE 
BULLETIN without exceeding 110 flying hours.

### Page 7

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 7/14
  2008.05.07
  
 
 
 
1.E.2.b. Non-installed equipment: Before installing a MGB on a helicopter, comply with the instructions 
 given in paragraph 2.B.2., and if there is PR sealing compound, comply 
 with the instructions given in paragraph 2.B.3. 
 
 
NOTE 3 
 
The time limits specified above are maximum time limits 
enabling operators to detect any corrosion before it 
affects the integrity of the fitting/casing attachment.  
However, we recommend that you remove the PR 
sealing compound in compliance with paragraph 2.B.3. 
as soon as possible, in order to limit the risk of corrosion 
occurring in this area and thus avoid replacing the MGB.  
 
 
1.F. APPROVAL 
 
Approval is limited to civil version helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in this ALERT SERVICE BULLETIN was approved  
on May 06, 2008 under the authority of EASA Design Organization Approval No. 21J.056. 
 
 
 
1.G. MANPOWER 
 
Qualification: Mechanic. 
Time for the operations: For compliance with par agraphs 2.B.1., 2.B.2. and 2.B.4.: Approximately 
 30 minutes. 
 For compliance with paragraphs 2.B.1., 2.B.3. and 2.B.4.: 1 to 17 hours,  
 depending on the results of the check fo r absence of corrosion on the lower  
 parts of the anchoring fittings. 
   
 
1.H. WEIGHT AND BALANCE  
 
 Not applicable.

### Page 8

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 8/14
  2008.05.07
  
 
 
 
1.I. EFFECT ON ELECTRICAL LOADS 
 
Not applicable. 
 
 
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE 
 
Not applicable. 
 
 
1.K. REFERENCES 
 
Standard Practices Manual (MTC) Work Cards: 
- 20.04.04 
- 20.04.05 
- 20.05.01 
 
1.L. OTHER DOCUMENTS CONCERNED  
 
Not applicable. 
 
 
1.M. INTERCHANGEABILITY AND MIXABILITY OF PARTS  
 
Not applicable.

### Page 9

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 9/14
  2008.05.07
  
 
 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
 
2.A. GENERAL 
 
Not applicable. 
 
 
2.B. OPERATIONAL PROCEDURE  
 
2.B.1. Preliminary steps 
 
- Install the equipment providing access to the MGB. 
- Remove the cowling providing access to the MGB. 
 
 
2.B.2. Check all the lower parts of the MGB servo-control anchoring fittings, in order to make sure that there is 
no PR sealing compound 
 
As per Figure 1: 
 
- Check all the lower parts of the MGB servo-control anchoring fittings 
 using a lamp or a dentist’s mirror, in order to make sure that there is no PR sealing compound. 
 
Interpretation of the results: 
 
a) If there is no PR sealing compound on any of  the lower parts of the MGB servo-control 
anchoring fittings: 
 
- Leave as is. 
- Return the helicopter to flight condition in compliance with paragraph 2.B.4. 
 
b) If there is a bead of PR sealing compound on the lower part of at least one MGB servo-
control anchoring fitting: 
 
- Contact the Customer Service Technical Support Operations Department (STVM) to inform it 
that you have discovered a bead of PR sealing compound on the lower part  of the attachment 
fittings, 
by: 
 Tel: +33 (0)4.42.85.99.67 
 Fax: +33 (0)4.42.85.99.66.  
Email : Dyncomp.technical-support@eurocopter.com 
 
- Comply with paragraph 2.B.3. 
Or 
- Leave as is and return the helicopter to flight configuration in compliance with paragraph 2.B.4., 
then: 
- Comply with paragraph 2.B.3. according to the conditions specified in paragraphs 1.E.2.a.1.  
 or 1.E.2.a.2.

### Page 10

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 10/14
  2008.05.07
  
 
 
 
2.B.3. Check to make sure that there is no corrosion on the lower parts of the MGB servo-control anchoring 
fittings 
 
As per Figure 1: 
 
- Remove the bead of PR sealing compound from the lower part of the servo-control anchoring fitting(s) 
concerned. 
 
NOTE 1 
 
There are different procedures for removing the bead of PR sealing 
compound. The procedures applied by EUROCOPTER to facilitate 
removal are described below: 
 
Use of a bronze knife or a plexiglas spatula: 
- Carefully cut the bead of PR sealing compound from the two zones 
identified by (xxx) as shown on Figure 1 (zones located in the area 
of the hole for the lower bolt attaching the fitting).  
- Pull the bead of PR sealing compound gently from the cutting to 
prevent it from tearing. 
 
Use of plastic milling cutters: 
Designation: 50 mm diameter radial scoring disk – SR 
Part number: 30097 
Manufacturer:  
3M, St Paul, MN 55144-1000, USA 
3M, France Construction et Maintenance Aéronautique Bd de 
l'Oise 95006 Cergy Pontoise Cedex, France 
- Protect the adjacent areas from PR particle ejections. 
- Machine the bead of PR sealing compound with plastic milling 
cutters. You must stack several (at least 3) plastic milling cutters. 
- Remove the PR sealing compound residues using a plexiglas 
spatula or a bronze knife. 
 
 
Then: 
 
- Visually check using a lamp and a dentist’s mirror t hat there is no corrosion in the lower area of the 
Main Gearbox casing, between the two servo-control anchoring fitting attachment ribs.  
 
Interpretation of the results: 
 
a) If there is no corrosion in the lower area of the Main Gearbox casing, between the two servo-control 
anchoring fitting attachment ribs: : 
- If necessary, touch up protective treatment as per MTC Work Cards 20.04.04 and 20.04.05. 
- If the bead of PR sealing compound in the areas referred to is damaged, renew it as per MTC 
Work Card 20.05.01 (see Figure 1        ).

### Page 11

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 11/14
  2008.05.07
  
 
 
 
THE BEAD OF PR SEALING COMPOUND MUST BE APPLIED TO THE 
LATERAL EDGES AND TO THE UPPER PART OF THE SERVO-
CONTROL ANCHORING FITTINGS. NEVER APPLY A BEAD OF PR 
SEALING COMPOUND TO THE LOWER PART OF THE SERVO-
CONTROL ANCHORING FITTINGS. 
 
- Return the helicopter to flight configuration as per paragraph 2.B.4. 
 
b) If there is corrosion on at least one MGB servo-control anchoring fitting lower part: 
 
- Suspend flights immediately or at the latest at the time limits specified in paragraph 1.E.2.a.1. 
or 1.E.2.a.2. 
- Comply with Repair Sheet FR 365-63-36-08 before resuming flights. 
- Return the helicopter to flight configuration in compliance with paragraph 2.B.4. 
 
NOTE 2 
 
Repair Sheet (FR) 365-63-36 -08 is available from the 
Customer Service Technical Support Operations 
Department (STVM) on the operator’s request: 
Tel: +33 (0)4.42.85.99.67 
Fax: +33 (0)4.42.85.99.66 
Email : Dyncomp.technical-support@eurocopter.com 
 
 
2.B.4. Final steps 
 
Install the cowlings providing access to the MGB. 
Remove the equipment providing access to the MGB. 
 
 
 
2.C. IDENTIFICATION 
 
Record compliance with this ALERT SERVICE BULLETIN on the log card of the MGB after having 
complied with paragraph 2.B.2., and where applicable: 
Record compliance with this ALERT SERVICE BULLETIN on the log card of the MGB after having 
complied with paragraph 2.B.3. 
 
 
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS 
 
Not applicable. 
 
 
 
CAUTION

### Page 12

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 12/14
  2008.05.07
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Lower part of the MGB servo-control anchoring fittings  
No bead of PR sealing compound  Bead of PR sealing compound applied 
Figure 1 – Location of the anchoring fittings and beads of PR sealing compound 
Servo-control anchoring 
fitting 
Location of the beads of 
PR sealing compound 
Lower attachment bolt
Lower attachment bolt
Locations of the 
servo-control 
anchoring fittings 
Zones(XXX)

### Page 13

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 13/14
  2008.05.07
  
 
 
 
3. MATERIAL INFORMATION  
 
3.A. MATERIAL: COST – AVAILABILITY 
 
Not applicable. 
 
 
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT  
 
Not applicable. 
 
 
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER / ENGINE / COMPONENT 
 
The products required for compliance with the Tasks and / or Work Cards listed in paragraph 1.K., can 
be ordered from the INTERTURBINE company: 
Website: http://www.itlogistics.de 
Telephone: +49.41.91.809.300 
AOG: +49.41.91.809.444 
 
 
3.D. MATERIAL REQUIRED FOR EACH SPARE PART 
 
Not applicable. 
 
 
3.E. RE-IDENTIFIED PARTS 
 
 Not applicable. 
 
 
3.F. TOOLING: COST – AVAILABILITY 
 
 Not applicable.

### Page 14

T.F.S. No. 00000449 
Approved under EASA DOA No. 21J.056.  Page 14/14
  2008.05.07
  
 
 
3.G. PROCUREMENT CONDITIONS  
 
Order the required quantity (unless otherwise specified) 
 
from 
 
EUROCOPTER 
Etablissement de Marignane 
Direction Ventes et Relation Client 
ECR 
13725 MARIGNANE CEDEX 
FRANCE 
NOTE 1 
 
For ALERT SERVICE BULLETINS, order by: 
Telex: HELICOP 410 969F 
Fax: +33 (0)4 42 85 99 96 
 
 
NOTE 2 
 
On the purchase order, please specify the 
mode of transport, the destination and the 
serial numbers of the helicopters to be 
modified. 
 
 
4. APPENDIX 
  
 Not applicable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
