# Eurocopter Emergency Alert Service Bulletin 76A001

Copy: No revision named ("U.S. DOT/FAA - Eurocopter ASB 76A001"), 12 pages: PDF https://openairdocs.org/files/sha256/15/f0/15f036f65ac25fea76a5bd1642207bdbe0563dab84c43453368aeafd91ba41fe; text https://openairdocs.org/service-documents/airbus-helicopters/76a001/file/15f036f65ac2.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2007-28229, the docket of AD 2008-06-22. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 76A001
- Page: https://openairdocs.org/service-documents/airbus-helicopters/76a001

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2014-11-08](https://openairdocs.org/ad/2014-11-08.md), effective Jul 8, 2014: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/76a001/proposed.md).

## Text (12 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2007-28229, the docket of AD 2008-06-22. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
EUROCOPTER
DIRECTION TECHNIQUE SUPPORT
13725 MARIGNANE CEDEX FRANCE  CIVIL VERSION(S):  B4
ALERT SERVICE BULLETIN
No. 76A001
SUBJECT:  ENGINE CONTROLS
Check of the Twist Grip Drive Tube and Control Pinion Attachment
REVISION No.  DATE OF APPROVAL  DATE OF ISSUE
Revision O  Date: February 9, 2006  2006.02.10
Approved under EASA DOA No. 21J.056.  76A001  Page 1/11
2006.02.10

### Page 2 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters / Installed equipment:
Helicopters equipped with twist grip assemblies with serial numbers:
- below 64, on the pilot's side (P/N 350A27520900, 350A27520901, 350A27520902 or 350A27520903),
- below 67, on the copilot's side (P/N 350A27521201).
NOTE
To be able to read the serial number, disengage boot (c)
(Figure 1). If necessary, disengage protecting sleeve (d).
1.A.2. Non-installed equipment:
Twist grip assemblies with serial numbers:
- below 64, on the pilot's side (P/N 350A27520900, 350A27520901, 350A27520902 or 350A27520903),
- below 67, on the copilot's side (P/N 350A27521201).
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
The purpose of this ALERT SERVICE BULLETIN which will form the subject of an Airworthiness Directive
issued by the DGAC on behalf of the EASA, is to ensure correct bonding strength of the control pinion on the
pilot and copilot collective lever drive tubes.
1.D. DESCRIPTION
A customer has informed EUROCOPTER that during an autorotation training procedure, the engine
remained at idle rating although the twist grip had been turned back to the flight position. The autorotation
procedure was continued without damage and the helicopter was landed.
Analysis has revealed failure of the twist grip drive tube and control pinion bonded attachment due to non-
compliant surface preparation.
Compliance with this ALERT SERVICE BULLETIN consists in applying a load to the twist grips in order to
check the bonding strength.
This check is included in the manufacturing process for twist grips with serial numbers above those specified
in "EFFECTIVITY" paragraph 1.A..
Approved under EASA DOA No. 21J.056.  76A001  Page 2/11
2006.02.10

### Page 3 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
1.E. COMPLIANCE
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.
1.E.1. At the works
1.E.1.a. On helicopters / installed equipment: Before delivery, check the bonding between the pilot and copilot
collective lever drive tubes and the control pinions, in compliance
with paragraphs 2.B.1. and 2.B.2.
1.E.1.b. On spares: Before installation on a helicopter, check the bonding between the drive tube and the control
pinion in compliance with paragraph 2.B.3.
1.E.2. Retrofit action: By the operator,
1.E.2.a. On helicopters / installed equipment: Check the bonding between the pilot and copilot collective lever
drive tubes and the control pinions, in compliance with
paragraphs 2.B.1. and 2.B.2., within 110 flying hours or 4
months (the first limit reached is applicable) following receipt of
this ALERT SERVICE BULLETIN, issued on the date indicated
in the footer.
1.E.2.b. On spares: Before installation on a helicopter, check the bonding between the drive tube and the control
pinion in compliance with paragraph 2.B.3.
1.F. APPROVAL
Approval is limited to civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN was approved on
February 9, 2006 under the authority of EASA Design Organisation Approval No. 21J.056.
1.G. MANPOWER
Qualification: 1 mechanic.
Time: Approximately 15 minutes for the check, and approximately 2 hours for replacement (as necessary).
Approved under EASA DOA No. 21J.056.  76A001  Page 3/11
2006.02.10

### Page 4 (OCR)

eurocopter  an EADS Company
ALERT SERVICE BULLETIN EC130
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE
Not applicable.
1.K. REFERENCES
Aircraft Maintenance Manual (AMM): Task 67-12-00, 4-1.
1.L. OTHER DOCUMENTS CONCERNED
Not applicable.
1.M. INTERCHANGEABILITY AND MIXABILITY OF PARTS
Not applicable.
Approved under EASA DOA No. 21J.056.  76A001  Page 4/11
2006.02.10

### Page 5 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
2. ACCOMPLISHMENT INSTRUCTIONS
2.A. GENERAL
The check of the bonding between the twist grip drive tube and the control pinion, described paragraph
2.B.2. applies to the copilot collective lever (a). This same check must be applied to the pilot collective
lever (b).
2.B. OPERATIONAL PROCEDURE
2.B.1. Preliminary steps
- Make sure that the pilot and copilot twist grips are set to "OFF".
- De-energize the aircraft electrical power system.
2.B.2. Check of the bonding between the twist grip drive tube and the control pinion
- Apply a load to the twist grip:
. On the twist grip of the copilot collective lever, as indicated on Figure 1, install twist grip adjusting
gage (g) or an adjusting gage made locally, consisting of one clamp (3), one bolt (4), one nut (5) and one
metal piece to be used as a lever arm, as shown on Figure 3.
NOTE 1
The twist grip adjusting gage (g) is available from
EUROCOPTER or can be made as shown on Figure 2.
. Using spring scale (h), apply a load of 35 N, tangentially to the twist grip of collective lever (a), in the
"reduction" direction.
NOTE 2
Apply a load of 35 N to the gage along arc A in order to
prevent the unfolding of clamp (3).
- If the twist grip does not turn, leave as is.
- If the grip turns:
. Replace the collective lever as per AMM Task 67-12-00, 4-1, before resuming flights.
NOTE 3
The non-compliant collective lever must be returned for
repair.
. Inform EUROCOPTER, by fax:
Département Opérations Support Technique
Service STXM
Fax: +33(0)4-42-85-99-66
- Remove twist grip adjusting gage (g) or the adjusting gage made locally.
Approved under EASA DOA No. 21J.056.  76A001  Page 5/11
2006.02.10

### Page 6 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
2.B.3. Check of the bonding between the twist grip drive tube and the control pinion on non-installed equipment
- Clamp area E of the collective lever, as shown on Figure 1, in a vice with soft jaws.
- Apply load to the twist grip:
• On the twist grip of the collective lever, as indicated on Figure 1, install twist grip adjusting gage (g) or an
adjusting gage made locally, consisting of one clamp (3), one bolt (4), one nut (5) and one metal piece to
be used as a lever arm, as shown on Figure 3.
NOTE 4
The twist grip adjusting gage (g) is available from
EUROCOPTER or can be made as shown on Figure 2.
• Using spring scale (h), apply a load of 35 N, tangentially to the twist grip of the collective lever, in the
"reduction" direction.
NOTE 5
Apply a load of 35 N to the gage along arc A in order to
prevent the unfolding of clamp (3).
- If the twist grip does not turn, leave as is.
- If the grip turns:
• Replace the collective lever.
NOTE 6
The non-compliant collective lever must be returned for
repair.
. Inform EUROCOPTER, by fax:
Département Opération Support Technique
Service STXM
Fax: +33(0)4-42-85-99-66
- Remove twist grip adjusting gage (g) or the adjusting gage made locally.
- Remove the collective lever from the vice.
2.C. IDENTIFICATION
Record compliance with this ALERT SERVICE BULLETIN in the aircraft documents.
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Approved under EASA DOA No. 21J.056.  76A001  Page 6/11
2006.02.10

### Page 7 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
b - 2
C - C
E
Figure 1: Collective levers
Approved under EASA DOA No. 21J.056.  76A001  Page 7/11
2006.02.10

### Page 8 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
10+0.5
15+0.5
5 × 5
32,3.  Ø 10,1
06
Ø 12
R13  40°
R25
14+0,5  R 12,5
10,5+0,5
010,1  _32,3,  2,5_  43  15+2
Ø12
Figure 2: Twist grip adjusting gage
Approved under EASA DOA No. 21J.056.  76A001  Page 8/11
2006.02.10

### Page 9 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
165
5
200
Figure 3: Gage made locally
Approved under EASA DOA No. 21J.056.  76A001  Page 9/11
2006.02.10

### Page 10 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
3. MATERIAL INFORMATION
3.A. MATERIAL: COST - AVAILABILITY
For any information, contact the Customer Support Sales Department.
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT
Not applicable.
3.C. MATERIAL REQUIRED FOR EACH AIRCRAFT, ENGINE/COMPONENTS
3.C.1. Component(s):
New Part Number  Qty  Item  Key Word  Former Part  Instructions
Number  Disposition
350A27521201  1  Copilot twist grip assembly
350A27520903  1  2  Pilot twist grip assembly
3.C.2. Material to be ordered separately:
New Part Number  Qty  Item  Key Word
ASNA0021-25G49  Clamp
22125BC050014L  1  Bolt
22431BC050L  1  5  Nut
The materials identified by an asterisk "*" or required for compliance with the tasks and/or work cards listed in
paragraph 1.K., can be ordered from the INTERTURBINE company,
Website: http://www.itlogistics.de
Phone: +49.41.91.809.300
AOG: +49.41.91.809.444
3.C.3. Tool (s):
Part Number  Qty  Item  Key Word
350A942720.00  g  Twist grip adjusting gage
h  Spring Scale
3.D. MATERIAL REQUIRED FOR EACH SPARE PART
Not applicable.
3.E. RE-IDENTIFIED PARTS
Not applicable.
Approved under EASA DOA No. 21J.056.  76A001  Page 10/11
2006.02.10

### Page 11 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
3.F. TOOLING: COST - AVAILABILITY
For any information, contact the Customer Support Sales Department.
3.G. PROCUREMENT CONDITIONS
Order the required quantity (unless otherwise specified)
from
EUROCOPTER
Etablissement de Marignane
Direction VENTES Service Client
S.V.
13725 MARIGNANE CEDEX
France
NOTE 1
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0) 4 42 85 99 96
NOTE 2
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
aircraft to be modified.
4. APPENDIX
Not applicable.
Approved under EASA DOA No. 21J.056.  76A001  Page 11/11
2006.02.10

### Page 12

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
