# Eurocopter Alert Service Bulletin 80A003

Copy: Revision 1 ("U.S. DOT/FAA - Eurocopter ASB No 80A003"), 11 pages: PDF https://openairdocs.org/files/sha256/2a/7e/2a7e42af780b100d0f0d8f1d0ceb5c99b850afa2817cd651350f87f24f4dd3ca; text https://openairdocs.org/service-documents/airbus-helicopters/80a003/file/2a7e42af780b.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-1228; AD 2011-10-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 80A003
- Latest revision known: 80A003, Revision 1, dated February 6, 2009 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/80a003

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-10-12](https://openairdocs.org/ad/2011-10-12.md), effective Jun 22, 2011: Revision 1

## Text (11 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-1228; AD 2011-10-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 1/11
  2009.02.06
    This document is available on the internet: www.eurocopter.com/techpub 
 
 EUROCOPTER   
 DIRECTION TECHNIQUE SUPPORT 
13725 MARIGNANE  CEDEX FRANCE CIVIL VERSION(S): B4 
     
       
ALERT SERVICE BULLETIN 
 
No. 80A003 
 
 
 
SUBJECT:  ENGINE STARTING  
 
Assembly check of AIRCRAFT PARTS CORPORATION (APC) starter-
generators with part numbers 150SG122Q and 200SGL130Q 
 
 
 
 
ATA: 80 
 
 
REVISION No.  
 
DATE OF APPROVAL 
 
DATE OF ISSUE 
 
   
   
Revision 0 On: December 19, 2008 2008.12.19 
Revision 1 On: February 05, 2009 2009.02.06

### Page 2

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 2/11
  2009.02.06
    
 
 
 
1. PLANNING INFORMATION  
 
1.A. EFFECTIVITY 
 
1.A.1. Helicopters/Installed equipment 
 
APC starter-generators with part numbers 150SG122Q and 200SGL130Q without “004” marking on their 
name plates. See Figure 1 - DETAIL B. 
 
1.A.2. Non-installed equipment 
 
APC starter-generators with part numbers 150SG122Q and 200SGL130Q without “004” marking on their 
name plates. See Figure 1 - DETAIL B. 
 
 
1.B. ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C. REASON 
 
Revision 0: 
To check the centering and tightness of the APC starter-generator damping assembly. 
 
Revision 0 of this ALERT SERVICE BULLETIN formed the subject of Airworthiness Directive No. 2009-0004. 
 
 
Revision 1: 
To improve the APC starter-generator damping assembly adjustment procedure. 
 
Revision 1 of this ALERT SERVICE BULLETIN will form the subject of an EASA Airworthiness Directive. 
 
Revision 1 of this ALERT SERVICE BULLETIN affects compliance with Revision 0. 
 
 
1.D. DESCRIPTION 
 
Revision 0: 
EUROCOPTER has received reports of Arriel engine flame-outs in operation. It was found that these engine 
flame-outs were due to the failure of the 41-tooth pinion in the engine accessory gear box. The failure of this 
pinion causes the fuel pump to stop and then results in an engine flame-out. 
The helicopters concerned were all equipped with starter-generators manufactured by the APC Company. 
In each case, it was found that the torque damping system of the starter-generators was inoperative.

### Page 3

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 3/11
  2009.02.06
    
 
 
 
Investigations have been conducted to assess the efficiency of the damping system of starter-generators 
with part numbers 150SG122Q and 200SGL130Q. 
These investigations have revealed that the non-operation of the torque damping system was due to 
incorrect adjustment of the starter-generator. 
If the damping system is incorrectly adjusted, torque oscillations may not be limited and, according to their 
intensity, can induce bending stress on the 41-tooth pinion of the accessory gear box. This occurrence can 
contribute to the failure of the pinion. 
 
EUROCOPTER is waiting for the results of additional investigations. 
 
In any case, in the short term, EUROCOPTER is introducing a check of the tightness of the starter-generator 
damping system in order to return it to conformity, where necessary, with the APC Component Maintenance 
Manual (CMM). 
 
Even though an engine failure is not qualified as a “condition jeopardizing safety” as regards certification, 
EUROCOPTER renders compliance with the instructions in this ALERT SERVICE BULLETIN, mandatory. 
 
 
Revision 1: 
 
Customers have reported some difficulty in complying with Revision 0 of this ALERT SERVICE BULLETIN. 
Following investigations conducted jointly by EUROCOPTER and APC, a new adjustment procedure has 
been defined which is more reliable and optimizes the APC starter-generator damping assembly. 
 
This new procedure consists in disassembling the damping system and replacing the Belleville springs (cup 
springs) and the self-locking nut, and then performing the assembly in accordance with a new adjustment 
method. 
 
Considering the service experience acquired, the angle measurements imposed by Revision 0 of this ALERT 
SERVICE BULLETIN are deleted from Revision 1. 
 
APC will send you an update of the Component Maintenance Manual (CMM) very shortly. This ALERT 
SERVICE BULLETIN conforms to the next update of the CMM. 
 
 
1.E. COMPLIANCE  
 
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN, mandatory. 
 
1.E.1. Compliance at the works 
 
1.E.1.a. On helicopters: Comply with paragraph 2 before delivery. 
 
1.E.1.b. On non-installed equipment: Comply with paragraphs 2.B.2., 2.B.3. and 2.C. before installation.

### Page 4

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 4/11
  2009.02.06
    
 
 
 
1.E.2. Compliance in operation: By the operator 
 
1.E.2.a. On helicopters/installed equipment 
 
On helicopters that have been subject or not to compliance with Revision 0: 
Comply with paragraph 2. of this ALERT SERVICE BULLETIN no later than within 110 flying hours 
without exceeding 3 months following receipt of Revision 1 of this ALERT SERVICE BULLETIN, issued on 
the date indicated at the foot of the page. 
 
1.E.2.b. On non-installed equipment 
 
Before any installation of a starter-generator and in any case before December 31, 2009, comply with 
paragraphs 2.B.2., 2.B.3. and 2.C. 
 
 
1.F. APPROVAL 
 
Approval is limited to civil version helicopters subject to an Airworthiness Certificate. 
 
The technical information given in Revision 0 of this ALERT SERVICE BULLETIN was approved  
on December 19, 2008 under the authority of EASA Design Organisation Approval No. 21J.056. 
 
The technical information given in Revision 1 of this ALERT SERVICE BULLETIN was approved  
on February 05, 2009 under the authority of EASA Design Organisation Approval No. 21J.056. 
 
 
1.G. MANPOWER 
 
Qualification: 1 mechanic. 
 
Time for the operations on a helicopter: 3 hours. 
Time for the operations on non-installed equipment: Half an hour. 
 
 
1.H. WEIGHT AND BALANCE  
 
Not applicable. 
 
 
1.I. EFFECT ON ELECTRICAL LOADS 
 
Not applicable. 
 
 
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE 
 
Not applicable.

### Page 5

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 5/11
  2009.02.06
    
 
 
 
1.K. REFERENCES 
 
Aircraft Maintenance Manual (AMM): 
- Task 24-31-00, 4-1. 
- Task 24-00-00, 3-1. 
 
Standard Practices Manual (MTC): 
- Work Card 20.02.05.404. 
 
Component Maintenance Manual (CMM): 
- 80.09.01 and 80.09.98. 
 
 
1.L. OTHER DOCUMENTS CONCERNED  
 
APC will modify the CMM: 80.09.01 and 80.09.98. 
 
 
1.M. TOOLING CONCERNED 
 
Not applicable. 
 
 
1.N. INTERCHANGEABILITY AND MIXABILITY OF PARTS  
 
Not applicable.

### Page 6

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 6/11
  2009.02.06
    
 
 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
 
2.A. GENERAL 
 
Comply with the general instructions concerning electrical power as per AMM Task 24-00-00, 3-1. 
Refer to the general instructions concerning assembly by bolts and nuts as per MTC Work  
Card 20.02.05.404. 
 
CAUTION  
 
DO NOT HANDLE THE STARTER-GENERATOR BY ITS 
SPLINED SHAFT. 
 
 
2.B. OPERATIONAL PROCEDURE  
 
2.B.1. Preliminary steps 
 
Install the access equipment. 
Open the engine cowling. 
Remove the starter-generator as per AMM Task 24-31-00, 4-1. 
 
2.B.2. Adjusting the starter-generators (Figures 1 and 2) 
 
- Remove the fan cover (a). 
- Lay down the starter-generator in the horizontal position on a stable workbench and remove the fan  
nut (c) and Belleville springs (cup springs) (b) or (d). 
- Discard nut (c) and springs (cup springs) (b) or (d). 
- Reinstall fan (a) with new Belleville springs (cup springs) (2) or (3) and new nut (1). 
Pay particular attention and refer to Figure 1 in order to have the Belleville springs (cup springs) (2) or (3) 
in the concave position. 
- Make sure that the shaft damping system is correctly aligned, as shown on Figure 2. 
- Tighten nut (1) using a fixed-type ratchet to just contact the Belleville springs (cup springs) (2) or (3). 
- Put the starter-generator in the vertical position, with fan (a) upward (on a support to avoid any stress on 
the shaft). 
- While holding the external part of the fan (a), torque tighten nut (1) to 30 lb.in (3.4 N.m) maximum using a 
calibrated torque wrench (Z). 
- Then loosen nut (1) by half (1/2) of a turn (180°). 
- Then tighten nut (1) by eighth (1/8) of a turn (45°). 
- Fit the fan cover, and reinstall the screws. 
- Secure the fan cover.

### Page 7

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 7/11
  2009.02.06
    
 
 
 
- Check for radial movement of the splined shaft to verify the damping system is not in a locked position 
(Figure 1 - DETAIL A), and realign the assembly as shown on Figure 2. 
 
NOTE 1 
 
A locked damping system is indicated by that disk (e) cannot be 
moved with respect to disk (f) when checking for radial 
movement (see Figure 2). 
 
- Punch-mark “004” on the name plate, as shown on Figure 1 - DETAIL B. 
- Comply with paragraph 2.B.3. 
 
2.B.3. Final steps 
 
Install the starter-generator as per AMM Task 24-31-00, 4-1. 
Close the engine cowling. 
Remove the access equipment. 
 
 
2.C. IDENTIFICATION 
 
Record compliance with Revision 1 of this ALERT SERVICE BULLETIN in the helicopter documents and on 
the starter-generator log card. 
 
 
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS 
 
2.D.1. Operating instructions 
 
Not applicable. 
 
2.D.2. Maintenance instructions 
 
Not applicable.

### Page 8 (OCR)

eurocopter
an EADS Company
ALERT SERVICE BULLETIN EC130
d- 3
Starter-generator P/N 150SG122Q  Starter-generator P/N 200SGL130Q
DETAIL A
004  STARTES CRAFT  GENERATOR  004  STARTER - GENERATOR
DESIGNATION  AIRCRAF
150SG122Q  CONTRACT No.  TOBEL NO.  TSO-C56  A DATE  STOCK No.  WCT. LES  200SGL130Q  TrODEL No.  TSO-C56  No.  STOCK No.  DESSONAFION
19.38  CONTRACT No.  WGT. LES
STARTER  GENERAT SPEED, RPIN  - -  19.38
24  VOLT. MAX  28  AMPS. MAX.  500  VOLTS  30 150  AMPS  - 7,200-12,100  VOLT. MAX 500  STARTER  AMPS. MAX. VOLTS  1 30 18 17.200-12,100  GENERATOR  SPEED, RPM
INSP  SERIAL No.  ROTATION  DETAIL B  24  28  INSP  SERIAL No  ROTATION
CCW
cCW
HOLTSVILLE, N.Y. 11742.  AIRCRAFTI  ¡PARTS CORP  HOLTSVILLE,  AIRCRAFT  PARTS CORP  , N.Y. 11742
Figure 1: Assembly of the starter-generators
Approved under EASA DOA No. 21J.056.  80A003  Page 8/11
2009.02.06

### Page 9

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 9/11
  2009.02.06
    
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2: Alignment of the shaft/damper assembly 
Compliant alignment of the shaft/damper assembly 
Non-compliant alignment of the shaft/damper assembly 
e f

### Page 10

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 10/11
  2009.02.06
    
 
 
 
3. MATERIAL INFORMATION  
 
3.A. MATERIAL: COST - AVAILABILITY 
 
3.A.1. Cost 
 
The components will be delivered free of charge on Customer's order until December 31, 2009. 
 
3.A.2. Availability 
 
The industrial delivery time will be given by the Sales and Customer Relations Department on the operator’s 
request.  
 
 
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT  
 
Not applicable. 
 
 
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER/ENGINE/COMPONENT 
 
3.C.1. Kit(s) or component(s) to be ordered for one helicopter or one assembly 
 
Not applicable. 
 
3.C.2. Items to be ordered separately 
 
3.C.2.a. Items to be ordered for starter-generators P/N 150SG122Q 
 
Material Part Number Qty Item Key Word 
    
150SG1071 1 1 Nut 
150SG1093 2 2 Belleville spring ( cup spring) 
 
3.C.2.b. Items to be ordered for starter-generators P/N 200SGL130Q 
 
Material Part Number Qty Item Key Word 
    
150SG1071 1 1 Nut 
200SGL1093 2 3 Belleville spring ( cup spring) 
 
The materials identified by an asterisk "*" or required for compliance with the Tasks and/or Work Cards listed in 
paragraph 1.K., can be ordered from the INTERTURBINE company: 
Website: http://www.itlogistics.de 
Phone: +49.41.91.809.300 
AOG: +49.41.91.809.444.

### Page 11

ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 11/11
  2009.02.06
    
 
 
 
3.C.3. Tool(s) 
 
Material Part Number Qty Item Key Word 
    
Off the shelf 1 Z Torque wrench with +/- 1.0 lb.in 
(0,11 N.m) tolerance (metric system)
 
 
3.D. PROCUREMENT CONDITIONS  
 
Order the required quantity (unless otherwise specified) 
 
from 
 
EUROCOPTER 
Etablissement de Marignane 
Direction Ventes et Relations Client 
ECR 
13725 MARIGNANE CEDEX 
FRANCE 
 
NOTE 1 
 
For ALERT SERVICE BULLETINS, order by: 
Telex: HELICOP 410 969F 
Fax: +33 (0)4 42 85 99 96. 
 
NOTE 2 
 
On the purchase order, please specify the mode of transport, 
the destination and the serial numbers of the helicopters to be 
modified. 
 
 
4. APPENDIX 
 
Not applicable. 
 
 
 
  
 ALERT SERVICE BULLETIN EC130 
Approved under EASA DOA No. 21J.056.     80A003 Page 11/11
  2009.02.06
    
 
 
 
3.C.3. Tool(s) 
 
Material Part Number Qty Item Key Word 
    
Off the shelf 1 Z Torque wrench with +/- 1.0 lb.in 
(0,11 N.m) tolerance (metric system)
 
 
3.D. PROCUREMENT CONDITIONS  
 
Order the required quantity (unless otherwise specified) 
 
from 
 
EUROCOPTER 
Etablissement de Marignane 
Direction Ventes et Relations Client 
ECR 
13725 MARIGNANE CEDEX 
FRANCE 
 
NOTE 1 
 
For ALERT SERVICE BULLETINS, order by: 
Telex: HELICOP 410 969F 
Fax: +33 (0)4 42 85 99 96. 
 
NOTE 2 
 
On the purchase order, please specify the mode of transport, 
the destination and the serial numbers of the helicopters to be 
modified. 
 
 
4. APPENDIX 
 
Not applicable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
