# Eurocopter Service Bulletin C-2-85A-042

Copy: No revision named ("Airbus Helicopters ASB BK117 C-2-85A-042 Rev 0"), 17 pages: PDF https://openairdocs.org/files/sha256/bb/a4/bba4964f229252a517880b084bec03c9edc38a15f35b2691f216c91fa244d2b0; text https://openairdocs.org/service-documents/airbus-helicopters/c-2-85a042/file/bba4964f2292.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1171, the docket of AD 2021-10-15. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Service Bulletin)
- Number: C-2-85A-042
- Page: https://openairdocs.org/service-documents/airbus-helicopters/c-2-85a042

## Text (17 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1171, the docket of AD 2021-10-15. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
Valid for Version(s): C-2.
ALERT SERVICE BULLETIN
SUBJECT:  OPTIONAL EQUIPMENT - Outboard Load System - Introduction of
life limit, a first time and repetitive inspection and replacement of
quick release pin bolts
For the attention of
Revision No.  Date of issue
Revision 0  2017-07-24
Summary:
This Alert Service Bulletin (ASB) introduces a life limit, a first time and repetitive inspection and
replacement of quick release pin bolts.
LH side shown.
Compliance:
Compliance with this ASB is mandatory.
Revision 0, 2017-07-24  PAGE 1 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  _ ASB MBB-BK117 C-2-85A-042
PLANNING INFORMATION
1.A EFFECTIVITY
1.A.1 Helicopters/installed equipment and parts
a) MBB-BK117 C-2, all S/N.
b) (1) Adapter (installed FWD)  P/N  B851M0010101
(quick release pin bolts)  P/N  (51399C10T30MS) or
Adapter FWD  P/N  D851M2044101
(2) Adapter (installed AFT LH)  P/N  B851M0010101
(quick release pin bolts)  P/N  (51399C10T30MS) or
Adapter AFT LH  P/N  D851M2042101
Adapter (installed AFT RH)  P/N  B851M0010101
(quick release pin bolts)  P/N  (51399C10T30MS) or
Adapter AFT RH  P/N  D851M2043101
(3) Fitting FWD (with bolts)  P/N  B851M0002101
(4) Fitting AFT (with bolts)  P/N  B851M0003101
(5) Fitting assy LH  P/N  B851M0011101
Fitting assy RH  P/N  B851M0020101
(6) X-Load Strut  P/N  B851M00X1001
(7) X-Load Fitting LH  P/N  B851M0006101
X-Load Fitting RH  P/N  B851M0021101
(8) Backup Fitting and airframe  P/N  B533K3002
4
LH side shown.
8
PAGE 2 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
1.A.2 Non-installed equipment and parts
See Section 1.A.1 part b).
1.B  ASSOCIATED REQUIREMENTS
None.
1.C  REASON
In consideration of the Human External Cargo (HEC) requirements, a dedicated life
limit of the adapter FWD (with quick release pin bolts) of the outboard load system
has to be introduced. Additionally the quick release pin bolts of the adapter FWD
must be replaced and the quick release pin bolts must be connected with wire ropes
to the adapter FWD and adapter AFT.
1.D  DESCRIPTION
Perform a first time inspection. Connect the quick release pin bolts to the adapter.
Reidentify the adapter. Create a log card. Introduce the life limit of the adapter FWD
(with quick release pin bolts) in the list of life-limited parts. Perform a repetitive
inspection.
1.E  COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
1. Introduce the life limit of the adapter FWD (with quick release pin bolts) in the
list of life-limited parts before delivery of the helicopter. For details refer to
Section 3.B.7.
2. Create a log card for the adapter FWD and enter the S/N of the adapter FWD
before delivery of the helicopter.
Non-installed equipment and parts:
Create a log card for the adapter FWD and enter the S/N of the adapter FWD before
delivery of the adapter FWD.
Revision 0, 2017-07-24  PAGE 3 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
1.E.2 Compliance in service
Helicopters/installed equipment and parts:
EFFECTIVITY: All Parts, refer to Section 1.A.1
1.  Latest Two months after receipt of this ASB:
a. Check the performed hoist cycles. For details refer to Section 3.B.1.
b. If the performed hoist cycles are unknown, the new basic can be determined
i.a.w. Section 3.B.2.
EFFECTIVITY: Adapter FWD with 12000 hoist cycles and up
2. Latest Two months after receipt of this ASB:
a. Perform a first time inspection. For details refer to Section 3.B.3.
b. Connect new quick release pin bolts to the adapter FWD and connect the
used quick release pin bolts to the adapter AFT. For details refer to Section
З.В.4.
c. Reidentify the adapter FWD and adapter AFT i.a.w. Section 3.B.5.
d. Create a log card for the adapter FWD. For details refer to Section 3.B.6.
e. Include the life limit of the adapter FWD in the list of life-limited parts. For
details refer to Section 3.B.7.
f. Perform a repetitive inspection of the adapter FWD and the quick release pin
bolts every 50 hoist cycles. For details refer to Section 3.B.3.
g. Replace the adapter FWD together with the quick release pin bolts by January
31, 2018 at the latest by a new adapter FWD (P/N D851M2044101)
EFFECTIVITY: Adapter FWD with less than 12000 hoist cycles
3. Latest Six months after receipt of this ASB:
a. Perform a first time inspection. For details refer to Section 3.B.3.
b. Connect new quick release pin bolts to the adapter FWD and connect the
used quick release pin bolts to the adapter AFT. For details refer to Section
З.В.4.
c. Reidentify the adapter FWD and adapter AFT i.a.w. Section 3.B.5.
d. Create a log card for the adapter FWD. For details refer to Section 3.B.6.
e. Include the life limit of the adapter FWD in the list of life-limited parts. For
details refer to Section 3.B.7.
f. Perform a repetitive inspection every 1800 hoist cycles i.a.w. Section 3.B.8.
Non-installed equipment and parts:
Refer to helicopters/installed equipment and parts.
PAGE 4 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
1.F  APPROVAL
Approval of this document:
The technical content of this document is approved under the authority of
DOA No. EASA.21J.700.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others
Estimated
Man-hours
approx. 2 h
(First time
inspection)
1.H  WEIGHT AND BALANCE
No effect on weight and balance.
1.l  POWER CONSUMPTION
Not affected.
1.J  SOFTWARE UPGRADES/UPDATES
Not changed.
1.K  REFERENCES
MSM MBB-BK117 C-2
1.L  OTHER AFFECTED PUBLICATIONS
Publications already updated:
AMM MBB-BK117 C-2.
Publications to be updated:
The changes to MSM MBB-BK117 C-2 and IPC MBB-BK117 C-2 which are required as
a result of this ASB will be incorporated with one of the next revisions.
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
Not affected.
Mixability:
Not affected.
Revision 0, 2017-07-24  PAGE 5 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
Information on price and availability of required material kit SB-117C2-85A-042-2C1
and SB-117C2-85A-042-2C2 will be provided by AHD, Dept. Spares Order
Administration on request.
All material kits required will be provided free of cost by AHD only within the time
limits that apply for the compliance (Section 1.E). Material that is ordered outside
the time limits given in the ASB will be charged according to the ruling prices.
2.B  LOGISTIC INFORMATION
None.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
Material kits to be ordered for one adapter:
EFFECTIVITY  Adapter FWD.
Material kit SB-117C2-85A-042-2C1 similar to design document D851M2044101.
No.  Keyword  Qty  New P/N  Old P/N  Rem.
Quick release pin  51399C10T30MS
1  4
bolt  51399C10T30MS
ISO2020B16Y
2  Wire rope  1
(120 cm)
TALURITKLEMME2
Clamp  12
ALU
4  Ring  4  40012N
Sheath
VG95343T05D002A
5  Heat-shrinkable  1
(100 cm)
sleeve
S/N
Adapter FWD
6  Serialization Sheet  1  B
(with quick release
pin bolts)
Remark:
A = AHD does not take back quick release pin bolts. Quick release pin bolts must be
discarded.
B = S/N used for the identification of the adapter FWD (with quick release pin bolts),
refer to Section 3.C.
PAGE 6 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
EFFECTIVITY  Adapter AFT.
NOTE  The quick release pin bolts of the adapter AFT will be reused.
Material kit SB-117C2-85A-042-2C2 similar to design document D851M2042101 /
D851M2043101.
NO.  Keyword  Qty  New P/N  Old P/N  Rem.
ISO2020B16Y
1  Wire rope  1
(120 cm)
TALURITKLEMME2
2  Clamp  12
ALU
Ring  4  40012N
Sheath
VG95343T05D002A
4  Heat-shrinkable  1
(100 cm)
sleeve
Consumables to be ordered separately:
Products can be ordered from the KLX Aerospace Solutions. The given CM numbers
are i.a.w. the Standard Practice Manual (MTC) list of consumable materials.
Website: https://www.klxaerospace.com
email: mailto:integration@klx.com
NOTE  Respect the safety data sheet of the manufacturer.
Qty.
NO.  Keyword  Specification **  Rem.
(approx.)
1  Cleaning solvent  a.n.*  218
2  Lacquer, single-layer  a.n.*  421
*a.n. = as needed
** Specification i.a.w. AMM, 01-00-00, 2-1.
Special tools:
Keyword  Qty.  Specification  Rem.
Pressing tool  1  Talurit pressing tool
Remark:
A = Specified pressing tool for talurit clamps.
2.D  MATERIAL TO BE RETURNED
None.
Revision 0, 2017-07-24  PAGE 7 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
Not applicable.
З.В  WORK STEPS
3.В.1  Check of performed hoist cycles
NOTE  If the hoist cycles are not documented, the new basic can be
determined i.a.w. Section 3.B.2.
1. Record the performed hoist cycles or new basic hoist cycles in the maintenance
schedule. The record of the hoist cycles must be continued.
For the affected parts / components refer to Table 1 and Figure 1.
Disposition  Part number  Rem.
Agapter installed FWD  B851M0010101  (1)(2)(3)
(quick release pin bolts)  (51399C10T30MS)
Adapter installed AFT LH  B851M0010101  (1)(2)(3)
(quick release pin bolts)  (51399C10T30MS)
Adapter installed AFT RH  B851M0010101  (1)(2)(3)
(quick release pin bolts)  (51399C10T30MS)
Fitting FWD (with bolts)  B851M0002101  (1) (2)
Fitting AFT (with bolts)  B851M0003101  (1)(2)
Fitting assy LH  B851M0011101  (1)(2)
Fitting assy RH  B851M0020101  (1)(2)
X-Load Strut  B851M00X1001  (1)(2)
X-Load Fitting LH  B851M0006101  (1)(2)
X-Load Fitting RH  B851M0021101  (1)(2)
Backup Fitting and airframe  B533K3002  (1)(2)
(1)  One hoist cycle is defined as an extension and subsequent retraction of the
hoist cable during flight or on the ground with a length of more than 5 m
(16 ft), independent of the load.
(2)  If you are operating other equipment than the rescue hoist system,
mounted to the fittings / adapters, make sure to record the number of
cycles as well.
For a definition of a cycle and recalculation to hoist cycles, contact the
manufacturer that is applicable for the dedicated equipment.
(3)  Valid for adapter after reidentification as well.
Table 1
PAGE 8 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
6
LH side shown.
1
1 Adapter installed FWD  B851M0010101
(with quick release pin bolts)  (51399C10T30MS)
2 Adapter installed AFT LH  B851M0010101
(with quick release pin bolts)  (51399C10T30MS)
Adapter installed AFT RH  B851M0010101
(with quick release pin bolts)  (51399C10T30MS)
Fitting FWD (with bolts)  B851M0002101
4 Fitting AFT (with bolts)  B851M0003101
5 Fitting assy LH  B851M0011101
Fitting assy RH  B851M0020101
6 X-Load Strut  B851M00X1001
7 X-Load Fitting LH  B851M0006101
X-Load Fitting RH  B851M0021101
8 . Backup Fitting and airframe  B533K3002
Check of performed hoist cycles
Figure 1
Revision 0, 2017-07-24  PAGE 9 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
3.B.2  Determination of the hoist cycles
OPERATION WITH A WEIGHT  FACTOR (HOIST CYCLES/FH)
ABOVE 150 KG  1.8
BELOW 150 KG  0.6
NOTE  In case of unknown operating weight, factor 1.8 must be used.
Calculating example for operating weight above 150 kg or unknown operating
weight:
Flight hours of the helicopter before accomplishment of this ASB = 3525 Fh
Factor = 1.8
3525 Fh x 1.8 hoist cycles/ Fh = 6345 hoist cycles
PAGE 10 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
З.В.З  First time Inspection
Accomplish an inspection, refer to AMM, 85-12-00, 6-1. For affected parts refer to
Table 2 and Figure 1.
Disposition  Part number  Rem.
Adapter installed FWD  B851M0010101
(quick release pin bolts)  (51399C10T30MS)
Adapter installed AFT LH  B851M0010101
(quick release pin bolts)  (51399C10T30MS)
Adapter installed AFT RH  B851M0010101
(quick release pin bolts)
Fitting FWD (with bolts)
Fitting AFT (with bolts)  B851M0003101
Fitting assy LH  B851M0011101
Fitting assy RH  B851M0020101
X-Load Strut  B851M00X1001
X-Load Fitting LH  B851M0006101
X-Load Fitting RH  B851M0021101
Backup Fitting and airframe  B533K3002
Table 2
Revision 0, 2017-07-24  PAGE 11 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
3.B.4 Connection of the quick release pin bolts to the adapter FWD and adapter AFT
Before connection  After connection
B851M0010101  B851M0011101 (LH)  B851M0020101 (RH)  D851M2044101
B851M0010101  D851M2042101 (LH)
51399C10T30MS  D851M2043101 (RH)
51399C10T30MS
NOTE  In the following the procedure for one quick release pin bolt is
described. The procedure for all quick release pin bolts are
identical.
NOTE  For the adapter FWD use the new quick release pin bolts from the
material kit. For the adapter AFT reuse the quick release pin bolts.
WARNING
THE INSTALLATION OF THE RING TOGETHER WITH
THE WIRE ROPES MUST ASSURE THAT THE QUICK
RELEASE PIN BOLT CAN NO LONGER BE REMOVED.
1. Cut the wire rope from the material kit in four equal parts.
2. Thread the wire rope (3, Fig. 3) into the quick release pin bolt (1) and press the
clamp (4).
3. Slide the heat shrinkable sleeve (5, Fig. 3) onto the wire rope (3).
4. Thread the wire rope (3, Fig. 3) through the adapter (2), press the clamps (4) and
install the ring (6). For details refer to 1, /2, 3.
5. Shrink the heat shrinkable sleeve (5, Fig. 3). For details refer to 4.
PAGE 12 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
5 /4
3
6
5/4
1 Quick release pin bolt  51399C10T30MS
2 Adapter
3 Wire rope  ISO2020B16Y
4 Clamp  TALURITKLEMME2 ALU
5 Heat shrinkable sleeve  VG95343T05D002A
6 Ring  40012N
Install clew as near and tight as possible to quick release pin bolt.
Adjust clew length so that the quick release pin bolt is easy to remove.
• In marked area install cable as short as possible. Maximum way for quick release
pin bolt 14 mm.
Install and shrink heat shrinkable sleeve (3 parts) in the shaded area.
Connection of quick release pin bolts
Figure 3
Revision 0, 2017-07-24  PAGE 13 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
З.В.5  Reidentification of the adapter FWD and adapter AFT
Reidentify the adapter FWD (with quick release pin bolts) and adapter AFT (with
quick release pin bolts) with the new P/N:
1. Using cleaning solvent (CM 218), clean grease and dirt from the surface
which is to be marked.
2. Using a permanent marker, mark the adapter FWD (with quick release pin bolts)
and adapter AFT (with quick release pin bolts) with the new P/N next to the
existing P/N. For details refer to Section 3.C.
3. Using a permanent marker, cross out the existing P/N but in such way that it is
still legible.
EFFECTIVITY  Adapter FWD.
4. Serial the adapter FWD with the S/N which is provided together with the
material kit (Serialization Sheet):
a. Using cleaning solvent (CM 218), clean grease and dirt from the surface
which is to be marked.
b. Using a permanent marker and mark the adapter FWD assy with the S/N,
close to the P/N. For details refer to Section 3.C.
c. Protect the marking with lacquer single-layer (CM 421).
3.B.6  Creation of a log card for the adapter FWD
Create a log card for the adapter FWD. For creation of a log card refer to MSM,
05-00-00, 6-1, Section G.6.0.3.
PAGE 14 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
3.B.7 Introduction of a Life Limit
NOTE  If the hoist cycles are not documented, the new basic can be
determined i.a.w. Section 3.B.2.
If the hoist cycles are not traceable, the adapter FWD must be
replaced by P/N D851M2044101.
NOTE  Prior to the distribution of the revised MSM MBB-BK117 C-2 / AMM
MBB-BK117 C-2 apply the life limit according Table 3.
Confirm the new introduced life limits by an entry in the list of life limited-parts and
in the corresponding log cards of the components /parts.
600 Ibs Rescue Hoist for HEC (85-12)
Disposition  Part number  Life limit entry
old  new
Adapter FWD  D851M2044101  12000 hoist cycles
(with quick release  (1)(4)  (2) (3)
pin bolts)
(1) The quick release pin bolts must be replaced together with the adapter FWD
assy.
(2) One hoist cycle is defined as an extension and subsequent retraction of the
hoist cable during flight or on the ground with a length of more than 5 m
(16 ft), independent of the load.
(3) If you are operating other equipment than the rescue hoist system, mounted
to the fittings / adapters, make sure to record the number of cycles as well.
For a definition of a cycle and recalculation to hoist cycles, contact the
manufacturer that is applicable for the dedicated equipment.
(4) If a quick release pin bolt cannot explicitly be correlated to the adapter FWD,
a new quick release pin bolt must be attached to the adapter FWD.
The life limit of the adapter FWD (with quick release pin bolts) remains
unchanged, though.
Table 3
Revision 0, 2017-07-24  PAGE 15 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
3.B.8  Repetitive Inspection
NOTE  Prior to the distribution of the revised MSM MBB-BK117 C-2 apply
the inspection interval according Table 2.
1. Accomplish an inspection, refer to AMM, 85-12-00, 6-1. For affected parts refer
to Table 2.
600 Ibs Rescue Hoist for HEC (85-12)
Disposition  Part number  Inspections  Rem.
old  new
Adapter FWD  D851M2044101  1800 hoist  (1)(2)
with quick  cycles
release pin bolts
Adapter AFT  D851M2042101  1800 hoist  (1)(2)
with quick  D851M2043101  cycles
release pin bolts
and X-Load
Fitting
Fitting FWD  B851M0002101  1800 hoist  (1)(2)
(with bolts)  cycles
Fitting AFT  B851M0003101  1800 hoist  (1)(2)
(with bolts)  cycles
X-Load Strut  B851M00X1001  1800 hoist  (1)(2)
cycles
X-Load Fitting  B851M0006101  1800 hoist  (1)(2)
B851M0021101  cycles
Backup Fitting  B533K3002  1800 hoist  (1) (2)
and airframe  cycles
(1) One hoist cycle is defined as an extension and subsequent retraction of the
hoist cable during flight or on the ground with a length of more than 5 m
(16 ft), independent of the load.
(2) If you are operating other equipment than the external mounted hoist,
mounted to the fittings / adapters, make sure to record the number of cycles
as well.
For a definition of a cycle and recalculation to hoist cycles, contact the
manufacturer that is applicable for the dedicated equipment.
Table 2
PAGE 16 of 17  Revision 0, 2017-07-24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB MBB-BK117 C-2-85A-042
З.С  COMPLIANCE CONFIRMATION
Tracking of modifications in the documentation:
1. Enter the P/N D851M2044101, the S/N and the hoist cycles determined
according Section 3.B.1 into the log card.
2. Enter the P/N and the S/N of the adapter FWD (with quick release pin bolts) with
their life limit (see Table 3) into the List of Parts to be Recorded.
Compliance with this document:
Confirm accomplishment of this ASB by an entry in the historical record of the
helicopter and in the log card of the adapter FWD.
Identification of modifications of adapter FWD and adapter AFT:
Keyword  Old P/N  New P/N  S/N  Marking Type
Adapter FWD
(with quick  B851M0010101  D851M2044101  ASBXXX (A)  Water-
release pin  resistant Pen
bolts)
Adapter AFT LH
(with quick
Water-
release pin  B851M0010101  D851M2042101
resistant Pen
bolts and X-load
fitting)
Adapter AFT RH
(with quick  Water-
release pin  B851M0010101  D851M2043101
resistant Pen
bolts and X-load
fitting)
Remark:
A = According the S/N which is provided together with the material kit (Serialization
Sheet).
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
None.
Maintenance instructions:
None.
4  APPENDIX
None.
Revision 0, 2017-07-24  PAGE 17 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
