# Eurocopter Service Bulletin D-2-88A-006

Copy: No revision named ("Airbus Helicopters ASB MBB-BK117 D-2-88A-006 Rev 0"), 13 pages: PDF https://openairdocs.org/files/sha256/0e/68/0e6807ad514ab813f01bdbe29e6a7bc660155a9371b842c5a2aa2ee23f527ca4; text https://openairdocs.org/service-documents/airbus-helicopters/d-2-88a006/file/0e6807ad514a.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0779, the docket of AD 2021-23-18. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Service Bulletin)
- Number: D-2-88A-006
- Page: https://openairdocs.org/service-documents/airbus-helicopters/d-2-88a006

## Text (13 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0779, the docket of AD 2021-23-18. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
Valid for Version(s): D-2, D-2m.
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
WIRING HARNESS - Cockpit wiring harness
Inspection of the wire harness at the lateral control rod
For the attention of
Revision No.  Date of issue
Revision O  2020-10-28
Summary:
With this Alert Service Bulletin (ASB), Airbus Helicopters prescribes a one-time inspection of the
wire harness at the lateral control rod.
Compliance:
It is mandatory to obey this ASB.
Revision 0, 2020-10-28  PAGE 1 of 9
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
1  PLANNING INFORMATION
1.A EFFECTIVITY
1.A.1 Helicopters/installed equipment and parts
a) MBB-BK117 D-2, D-2m, all S/N up to 20334 inclusive, excluding S/N 20274,
20281, 20284, 20286, 20320, 20322, 20327, 20328, 20331 and 20332 (*).
(*) On the excluded S/N and with S/N 20335 and on, the inspection of the wire harness at the
lateral control rod is accomplished in the serial production.
b) Wire harness in the affected area:
View A
Affected area
1 Cyclic stick
2 Wire harness
3 Lateral control rod
4 Trim actuator
1.A.2 Non-installed equipment and parts
Not applicable.
1.B  ASSOCIATED REQUIREMENTS
None.
PAGE 2 of 9  Revision 0, 2020-10-28
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
1.C  REASON
A chafing between a wire harness and the locking washer of the lateral control rod
was detected in the serial production. With this ASB an affected wire harness must
be identified by an inspection and the routing of the affected wire harness must be
corrected.
1.D  DESCRIPTION
Inspect the wire harness. If necessary, repair the wire harness and/or correct the
routing of the wire harness.
1.E  COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
Not affected.
Non-installed equipment and parts:
Not affected.
1.E.2 Compliance in service
Helicopters/installed equipment and parts:
The inspection of the wire harness must be accomplished in accordance with Section
3.B of this ASB within the next 100 Fh (tolerance 10 Fh) or 3 months whichever
occurs first after receipt of this ASB.
Non-installed equipment and parts:
Not affected.
1.F  APPROVAL
Approval of this document:
The technical content of this document is approved under the authority of
DOA No. EASA.21J.700.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others
approx. 1 h
(inspection)
Estimated
Man-hours  approx. 1 h
(repair and/or routing
correction, if required)
1.H  WEIGHT AND BALANCE
No effect on weight and balance.
Revision 0, 2020-10-28  PAGE 3 of 9
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
1.1  POWER CONSUMPTION
Not affected.
1.J  SOFTWARE UPGRADES/UPDATES
Not changed.
1.K  REFERENCES
AMM MBB-BK117 D-2, MTC MBB-BK117 D-2.
1.L  OTHER AFFECTED PUBLICATIONS
None.
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
Not affected.
Mixability:
Not affected.
PAGE 4 of 9  Revision 0, 2020-10-28
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
None.
2.B  LOGISTIC INFORMATION
None.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
None.
2.D  MATERIAL TO BE RETURNED
None.
Revision 0, 2020-10-28  PAGE 5 of 9
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
Obey the "General recommendations for Working at helicopter"
(AMM 00-10-02, 2-1).
З.В  WORK STEPS
3.B.1 Preliminary steps
1. Remove the bottom access cover (FWD) (AMM 52-40-00, 4-2).
3.В.2  Inspection of the wire harness at the lateral control rod
WARNING
RISK OF INJURY. MOVEMENT OF THE FLIGHT
CONTROLS CAN CAUSE INJURY TO YOUR HANDS
AND/OR FINGERS. MAKE SURE THAT THE FLIGHT
CONTROLS DO NOT MOVE.
1. Inspect the wire harness (2, Fig. 1) in the affected area (3):
a. If the wire harness (2, Fig. 1) is damaged, categorize the damage of the wire
harness (2) and repair if needed (MTC 20-80-20-442).
b. If the wire harness (2, Fig. 1) is not damaged, proceed in accordance with
Section 3.B.2.2.
2. Make sure that the lockwire (6, Fig. 1) of the locking washer (7) and nut (8) is
installed correctly (MTC 20-02-06-402).
З.В.З  Inspection of the routing of the wire harness at the lateral control rod
1. Make sure that the clearance between the wire harness (2, Fig. 1) and the lateral
control rod (4) is sufficient (MTC 20-80-20-441):
a. If the clearance is sufficient, proceed in accordance with Section 3.B.3.3.
b. If the clearance is not sufficient, proceed in accordance with Section 3.B.3.2.
2. Correct the routing of the wire harness (2, Fig. 1):
a. Remove the bindings as required (MTC 20-80-20-402).
b. Move the wire harness (2, Fig. 1) to the correct position and install the
bindings as required (MTC 20-80-20-441) (MTC 20-80-20-402).
3. Connect the external pump drive to the hydraulic system 2 (AMM 29-00-00, 2-1).
PAGE 6 of 9  Revision 0, 2020-10-28
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
WARNING
DANGER OF INJURY. IF THE CONTROLS ARE MOVED,
INJURY TO PERSONNEL CAN OCCUR. MAKE SURE
THAT PERSONNEL ARE CLEAR OF THE CYCLIC
CONTROLS IN THE BOTTOM COMPARTMENT WHILE
YOU MOVE THE CYCLIC STICK. ALWAYS TELL THE
SECOND PERSON ABOUT THE OPERATION OF THE
CYCLIC STICK WELL IN ADVANCE BEFORE YOU MOVE
THE CYCLIC STICK.
NOTE  Two persons are required to do the procedure that follows.
4. Move the cyclic stick (1, Fig. 1) several times fully left and right. Make sure that
the clearance between the wire harness (2) and the lateral control rod (4) is
sufficient (MTC 20-80-20-441):
a. If the clearance is sufficient, proceed in accordance with Section 3.B.3.5.
b. If the clearance is not sufficient, proceed in accordance with Section 3.B.2.
5. Disconnect and remove the external pump drive from the hydraulic system 2
(AMM 29-00-00, 2-1).
Revision 0, 2020-10-28  PAGE 7 of 9
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
View A
FW D  View B  Detail A
8
1 Cyclic stick
2 Wire harness
3 Affected area
4 Lateral control rod
5 Trim actuator
6 Lockwire
7 Locking washer
8 Nut
Example for chafing between a wire harness and the lateral control rod
Figure 1
PAGE 8 of 9  Revision 0, 2020-10-28
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 D-2-88A-006
3.В.4  Final steps
1. Install the bottom access cover (FWD) (AMM 52-40-00, 4-2).
З.С  COMPLIANCE CONFIRMATION
Compliance with this document:
Record full compliance with this ASB, with the revision number, in the helicopter
documents.
Please confirm compliance with this ASB (see IN 3447-1-00 for details):
QR-Code or hypertext link
NOTE
The recording of compliance with ASBs in the R-Tex
tool does not replace the recording in the helicopter
documents
ASB MBB-BK117 D-2-88A-006
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
None.
Maintenance instructions:
NOTE  The pre-print of the trim system - adjustment / test
(AMM 67-14-00, 5-2) is published on ORION.
Until the distribution of the AMM MBB-BK117 D-2 containing the new instructions,
the trim system - adjustment / test (AMM 67-14-00, 5-2) must be used as shown in
Section 4.
4  APPENDIX
Pre-print of the trim system - adjustment / test (AMM 67-14-00, 5-2):
Revision 0, 2020-10-28  PAGE 9 of 9
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10

Aircraft Maintenance Manual (AMM) MBB-BK117
Trim System - Adjustment / Test
EFFECTIVITY
5-2 Adjustment - Duplex Trim Actuator Lateral
A. References:
24-32-00, 2-1 ................................. Energi ze / De-energize - Electrical System
24-32-00, 2-2 ................................. Discon nect / Connect - External Power Unit (EPU)
29-00-00, 2-1 ................................. Connec t / Disconnect - External Pump Drive
52-40-00, 4-2 ................................. Remova l / Installation - Bottom Access Cover (FWD)
67-10-00, 5-2 ................................. Operat ional Test - Free Movement of the Main Rotor
Controls
B. Special Tools:
None.
C. Consumable Materials:
CM 776 ......................................... Lockw ire
or
CM 7045 ....................................... Lockwi re
D. Routine Replacement Parts:
None.
E. Job Set-up:
(1) De-energize the electrical system (24-32-00, 2-1).
(2) Remove the FWD bottom access cover (52-40-00, 4-2).
(3) Connect the external pump drive to the hydraulic power sy stem 1 (29-00-00, 2-1).
(4) Connect the EPU to the helicopter (24-32-00, 2-2).
F. Procedure:
(1) Obey the related Material Safety Data Sheet and local reg ulations when you use
consumable materials.
(2) Energize the electrical system (24-32-00, 2-1).
(3) Switch on the external pump drive.
(4) Measure the offset of the center position of the duplex tr im actuator lateral (Table 501)
Figure 501 .
ALL 
Objective Method
Duplex trim actuator lateral range adjustment Do a check of the RVDT position ranges in
maintenance mode.
Table 501 Objective and Method
Conf. Code: 001 67-14-00, 5-2 Page 501
2020.09.25
PRE PRINT

### Page 11

Aircraft Maintenance Manual (AMM) MBB-BK117
(5) If the offset is not between -2˚ and 2˚, adjust the rod late ral (8, Figure 502 ) as follows:
(a) Remove and discard the Lockwire from the nuts (2, 6) and th e serrated discs (3, 7).
(b) Loosen the nuts (2, 6).
(c) Turn the tube (4) to increase or decrease the length until the offset is between -2˚
and 2˚.
(d) Manually tighten the nuts (2, 6).
1 Make sure that you cannot see the red markings (9, 10) on the th reads of the
fork end (1) and the rod end (5). If you can see the red markings (9, 10),
contact your local Airbus representative.
2 Make sure that the offset is between -2˚ and 2˚. If the offset i s not between -2˚
and 2˚, adjust the rod lateral (8) again as given above.
(e) Apply a torque between 5 Nm and 6 Nm (45 lbf.in and 53 lbf.in ) to the nuts (2, 6).
(f) Make sure that you cannot see the red markings (9, 10) on th e threads of the fork
end (1) and the rod end (5). If you can see the red markings (9, 1 0), contact your
local Airbus representative.
NOTE You can use the Lockwire CM 7045 as an alternative to the speci fied
Lockwire CM 776.
(g) Safety the nuts (2, 6) and the serrated discs (3, 7) with Lo ckwire CM 776.
(h) Do the free movement check of the main rotor controls (67- 10-00, 5-2).
(6) Switch off the external pump drive.
(7) De-energize the electrical system (24-32-00, 2-1).
G. Close-up:
(1) Disconnect the EPU from the helicopter (24-32-00, 2-2).
(2) Disconnect the external pump drive from the hydraulic po wer system 1 (29-00-00, 2-1).
(3) Install the FWD bottom access cover (52-40-00, 4-2).
(4) Remove all tools and other materials and clean the work ar ea.
Conf. Code: 001 67-14-00, 5-2 Page 502
2020.09.25
PRE PRINT

### Page 12

Aircraft Maintenance Manual (AMM) MBB-BK117
BKD26714M105100EN00
Step Action: Result:
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD+01.56
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD+01.12
1 On the APCP, push the knob TRK/HDG. The MFD shows ROLRVD and the numeric
position of the cyclic stick.
Calculate the sum of the numeric positions 
ROLRVD shown on the MFD of the two test 
steps above.
The sum of the numeric position ROLRVD
shown on the MFD is between −2 and +2.
4
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD+31.20
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD+31.20
2 The numeric position ROLRVD shown on the
MFD is between −29.2 and −33.2.
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD−31.20
AFCS MAINTENANCE MOD
POSITIONS
ROLRVD−31.20
3 The numeric position ROLRVD shown on the
MFD is between +29.2 and +33.2.
On the cyclic stick, push and hold the
pushbutton TRIM REL. 
Lightly move the cyclic stick to the LH side
until it gets to the end stop.
On the cyclic stick, release the pushbutton
TRIM REL.
On the cyclic stick, push and hold the
pushbutton TRIM REL. 
Lightly move the cyclic stick to the RH side
until it gets to the end stop.
On the cyclic stick, release the pushbutton
TRIM REL.
Adjustment - AFCS Maintenance Mode Positions
Figure 501
Conf. Code: 001 67-14-00, 5-2 Page 503
2020.09.25
PRE PRINT

### Page 13

Aircraft Maintenance Manual (AMM) MBB-BK117
BKD26714M104100MU01
CM 7761
A
1
1
1
1
FWD
B
C
BC
(45−53 lbf.in)
5−6 Nm
(45−53 lbf.in)
5−6 Nm
A
2
3
1
1
10
5
9
4
5
6
7
8
Adjustment - Duplex Trim Actuator Lateral
Figure 502
Conf. Code: 001 67-14-00, 5-2
END OF MODULE
Page 504
2020.09.25
PRE PRINT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
