# Airbus Helicopters Alert Service Bulletin EC120-32A014

Copy: Revision 1 ("Airbus Helicopters ASB EC120-32A014 Rev 1"), 22 pages: PDF https://openairdocs.org/files/sha256/4f/66/4f66524406469c21dc9e4a3c38a12ed39ec0c01245de4455763696ed56f65c86; text https://openairdocs.org/service-documents/airbus-helicopters/ec120-32a014/file/4f6652440646.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0016; AD 2023-14-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC120-32A014
- Latest revision known: EC120-32A014, Revision 1, dated October 17, 2022 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec120-32a014

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-14-06](https://openairdocs.org/ad/2023-14-06.md), effective Sep 8, 2023: Revision 1

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec120-32a014/proposed.md).

## Text (22 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0016; AD 2023-14-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
Civil version (s): B
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
LANDING GEAR - Landing gear
Inspection for corrosion on the landing gear
For the attention of
Revision No.  Date of issue
Revision 0  2022-02-15
Revision 1  2022-10-17
Summary:
During a landing gear inspection, corrosion was found on the rear and front crossbeams and on the junction of the
crossbeam and the skid
Airbus Helicopters thus makes the inspection of the landing gear of EC120 helicopters mandatory to make sure
that there is no corrosion on the external and internal sides of the landing gear tubes.
Reason for last Revision:
The purpose of revision 1 of this ALERT SERVICE BULLETIN is to clarify the effectivity and the inspection
procedure.
Compliance:
It is mandatory to comply with this ALERT SERVICE BULLETIN.
Revision 0 2022-02-15  Page 1/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.  PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
EC120 B helicopters that have a landing gear with an MP/N given in Table 1, and:
- A date of first installation on the helicopter before February 16, 2016 if it can be shown that the helicopter
on which it was installed has always been operated in standard conditions
or
- A date of first installation on the helicopter before February 15, 2022 if it can be shown that the helicopter
on which it was installed was operated in specific or severe atmospheric operating conditions.
NOTE 1
For helicopters that have the same landing gear as the one
installed at helicopter delivery, you can refer to the helicopter
airframe initial date of statement of conformity marked on the
helicopter identification plate to know the date of first
installation of the landing gear.
NOTE 2
- If you are not sure about the date of first installation of the
landing gear, the date of first installation of the landing
gear to record is before February 16, 2016.
- If you are not sure about the environmental conditions in
which it operated, record that the helicopter was operated
in specific or severe atmospheric operating conditions.
NOTE 3
A landing gear has two skids and two crossbeams. The age
of the landing gear is calculated by its oldest part.
NOTE 4
Specific or severe conditions are specified in the MSM "Use
of the MSM" chapter 5.7 "Specific and severe atmospheric
operating conditionsi
Table 1
Key Word  MP/N
C321A2106102
C321A2501101
C321A2501102
Landing gear assembly  C321A2601051AA
C321A2501051CA
C321A2501052
Revision 0 2022-02-15  Page 2/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbus  elicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.A.2. Non-installed equipment or parts
Landing gears or parts of EC120 B helicopters with an MP/N given in Table 2, and:
- With a date of first installation on the helicopter before February 16, 2016 if it can be shown that the
helicopter on which it was installed has always been operated in standard conditions
or
- With a date of first installation on the helicopter before February 15, 2022 if it can be shown that the
helicopter on which it was installed was operated in specific or severe atmospheric operating conditions.
NOTE 5
- If you are not sure about the date of first installation of the
landing gear, the date of first installation of the landing
gear to record is before February 16, 2016.
- If you are not sure about the environmental conditions in
which it operated, record that the helicopter was operated
in specific or severe atmospheric operating conditions.
NOTE 6
A landing gear has two skids and two crossbeams. The age
of the landing gear is calculated by its oldest part.
NOTE 7
Specific or severe conditions are specified in the MSM "Use
of the MSM" chapter 5.7 "Specific and severe atmospheric
operating conditions".
Table 2
Key Word  MP/N
C321A2106102
C321A2501101
C321A2501102
Landing gear assembly
C321A2601051AA
C321A2501051CA
C321A2501052
C321A2104101
Front crossbeam  C321A2506101
C321A2506102
C321A2105101
Rear crossbeam
C321A2507101
C321A2107101
C321A2107102
LH skid assembly  C321A2503101
C321A2503102
C321A2108101
C321A2108102
RH skid assembly  C321A2502101
C321A2502102
Revision 0 2022-02-15  Page 3/22
Revision 1 2022-10-17  This document is available on the Internet: www.ai  elicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Revision 0:
During an inspection, corrosion was found:
- On the rear crossbeam, at the clamp position
- On the rear junction fitting between the skid and the rear crossbeam
- In the splicing area between the front crossbeam and the skid.
Airbus Helicopters thus tells the customer to do an inspection of the landing gear of EC120 helicopters to
make sure that there is no corrosion on the external and internal sides of the landing gear tubes.
Revision 1:
The purpose of revision 1 of this ALERT SERVICE BULLETIN is to clarify the effectivity and the inspection
procedure.
Revision 1 of this ALERT SERVICE BULLETIN has an effect on the execution of the compliance with
Revision O for helicopters which have not done the inspection of the internal side of the landing gear tube
(paragraph 3.B.2.b.).
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN makes sure that there is no corrosion on the external and internal sides of
the landing gear tube.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
Revision 0 2022-02-15  Page 4/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.E.2. Compliance in service
It is the operator who does the work on the helicopter and on non-installed equipment.
Helicopters/installed equipment or parts:
- For helicopters which have not complied with revision 0 of this ALERT SERVICE BULLETIN:
• Helicopters with landing gear that was operated in standard conditions and with a date of first installation
on the helicopter before February 16, 2016:
.. Comply with paragraph 3. not more than 24 months and 73 days after you received Revision 0 of this
ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.
• Helicopters with landing gear that was operated in specific and severe atmospheric operating conditions
and first installed between February 16, 2016 and February 15, 2022:
.. Comply with paragraph 3.:
- Not more than 24 months and 73 days after you received Revision 0 of this
ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.
Or,
- Not more than 7 years after the first installation of the landing gear (the first limit you get to is
applicable).
• Helicopters with landing gear that was operated in specific and severe atmospheric operating conditions
and first installed before February 16, 2016:
.. Comply with paragraph 3. not more than 12 months and 36 days after you received Revision 0 of this
ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.
- For helicopters which have only done the external inspection through Revision 0 of this
ALERT SERVICE BULLETIN:
• Comply with paragraph 3.B.2.b (internal inspection) of this ALERT SERVICE BULLETIN in accordance
with the compliance time of Revision O. Refer to the issue date on the page footer.
NOTE 8
Removal of the landing gear is not necessary to do only the
internal inspection.
- For helicopters which have done the external and internal inspections through Revision 0 of this
ALERT SERVICE BULLETIN:
. No more action is required.
Revision 0  2022-02-15  Page 5/22
Revision 1  2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
Non-installed equipment or parts:
- For Landing gears or parts which have not complied with revision 0 of this
ALERT SERVICE BULLETIN:
• Comply with paragraph 3. (but this is not applicable to paragraphs 3.B.1. and 3.B.3.) of this
ALERT SERVICE BULLETIN before installation on the helicopter.
- For Landing gears or parts which have only done the external inspection through revision 0 of this
ALERT SERVICE BULLETIN:
. Comply with paragraph 3.B.2.b. (internal inspection) of this ALERT SERVICE BULLETIN in accordance
with the compliance time of Revision O. Refer to the issue date on the page footer.
- For Landing gears or parts which have done the external and internal inspections through
revision 0 of this ALERT SERVICE BULLETIN:
. No more action is required.
1.F. APPROVAL
Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on February 15, 2022 under the authority of EASA Design Organization Approval No. 21J.700 for civil
version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on
October 14, 2022 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
1.G. MANPOWER
Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this
qualification:
Qualification: 1 Mechanical Technician.
The man-hours are an estimate given for information only and for a standard helicopter configuration.
Estimated Man-hours: 2 hours for the Mechanical Technician to do the inspection.
The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.
The estimate of the helicopter downtime is half a day for the inspection.
Revision 0  2022-02-15  Page 6/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.H. WEIGHT AND BALANCE
There is no change in weight and moment.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
These documents are necessary to comply with this ALERT SERVICE BULLETIN:
Aircraft Manual Maintenance (AMM)
AMM: 32-12-00, 4-1: Removal / Installation - Landing Gear - Landing Gear
AMM: 32-12-00, 4-2: Assembly / Disassembly - Landing Gear - Landing Gear
AMM: 32-12-00, 8-2: Rivet Replacement - Forward Cross Tube / Skids Assembly - Landing Gear
Standard Practices Manual (MC)
MTC: 20-02-05-404: Assembly by screws and nuts - Joining
MTC: 20-02-06-404: Safetying with cotter pins - Safetying and locking assemblies
MTC: 20-04-01-102:  Use of cleaning products on individual parts and on aircraft - Cleaning
MTC: 20-04-01-402: Cleaning of removed individual parts with liquid solvents - Cleaning
MTC: 20-04-04-403:  Touch-up of the Alodine 1200 protection (Bonderite M-Cr 1200) - Surface treatment
before painting
MTC: 20-04-05-101:  Painting equipment and paint touch-ups - General - Paint and primer application
procedure
MTC: 20-04-05-402:  Application of Primer EPOXY P05-P20 - Paint and primer application procedure
MTC: 20-07-02-201: Helicopter parked in repair shop - Safety instructions
MTC: 20-07-03-408:  Appearance checks on an aircraft after an inspection or repair - Technical instructions
MTC: 20-08-05-103:  Monitoring of parts in operation - marking - service life customization - General rules
applicable to aircraft
MTC: 20-90-01-104:  Types of corrosion - General information on corrosion
MTC: 20-90-03-101:  Inspection methods - Corrosion detection
MTC: 20-90-03-106:  Ultrasonic detection - Corrosion detection
MTC: 20-90-04-101:  General - Corrosion treatment
MTC: 20-90-04-301:  Anti-corrosion products - Corrosion treatment
MTC: 20-90-04-401:  General reconditioning method for corroded surfaces - Corrosion treatment
MTC: 20-90-04-402:  Specific treatment procedures - Corrosion treatment
MTC: 20-90-05-101:  General information - Repairs
MTC: 20-90-05-401:  Alodine 1200 treatment (aluminum alloys) - Repairs
Information Notice (IN)
IN 3481-1-00: The Marketplace: an AirbusWorld Ordering service
IN 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight
Revision 0  2022-02-15  Page 7/22
Revision 1  2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
1.L. OTHER AFFECTED PUBLICATIONS
Airbus Helicopters will update the manuals shown below in relation to this ALERT SERVICE BULLETIN:
- Aircraft Maintenance Manual (AMM)
- Master Servicing Manual (MSM).
Airbus Helicopters will update the AMM and the MSM when the customer sends an order for them.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
This ALERT SERVICE BULLETIN has no effect on the interchangeability and mixability.
Revision 0 2022-02-15  Page 8/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
If the corrosion is more than the criteria and aligned with your Technical Event report, Airbus Helicopters will
apply a special commercial policy for new components, based on the age of the landing gear.
Avallability
Contact the Sales and Customer Relations Department to know the delivery lead times.
Procurement
Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations
Department:
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
In the purchase order, write the information that follows:
- The mode of transport
- The destination
- The serial numbers of the helicopters to change.
2.B. LOGISTIC INFORMATION
Not applicable.
Revision 0 2022-02-15  Page 9/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Kits to be ordered for one helicopter or one assembly:
Former
Key Word  Qty  New P/N  Item
P/N  →  Instruction
C321A2509201  C321A2509201
Blanking cap  2  or  1  or
C321A2509202  C321A2509202
Consumables to be ordered separately:
Refer to the Tasks and Work Cards identified in this ALERT SERVICE BULLETIN and the list below.
Key Word  Qty  P/N  CM  Item
Alodine 1200  A/R  CM 324  2
Primer P05  A/R  DHS186-111-20  CM 487  3
Primer P20  A/R  DHS186-111-40  CM 488  4
NOTE
When you order primer P05 (DHS186-111-20), you will also
order  hardener  (DHS186-111-21)  and  thinner
(DHS186-111-22).
You can send an order for the consumables from the AirbusWorld Marketplace through e-ordering
(IN 3481-1-00).
If you cannot get access to e-ordering, please contact your Logistic Focal Point.
Special tools:
Refer to the Tasks and Work Cards identified in this ALERT SERVICE BULLETIN and the list below:
Key Word  Qty  Tool P/N or equivalent  Item
Borescope  Commercial  ZZ
Olympus 45MG ultrasonic thickness  Commercial
gauge or equivalent
Virtual-45MG-EETC software opt  Commercial
or equivalent
Thru Coat Transducer D7908
or equivalent  Commercial
Standard aluminum 2024 step blocks  Commercial
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0  2022-02-15  Page 10/22
Revision 1  2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Comply with the instructions about the assembly by screws and nuts. Refer to
Work Card 20-02-05-404 (MTC).
- Comply with the instructions about the safetying with split pins. Refer to Work Card 20-02-06-404 (MTC).
- Comply with the general instructions about helicopters parked in a repair shop. Refer to
Work Card 20-07-02-201 (MTC).
- Comply with the general information about the types of corrosion. Refer to Work Card 20-90-01-104 (MTC).
- Comply with the inspection methods for corrosion detection. Refer to Work Card 20-90-03-101 (MTC).
- Comply with the instructions about ultrasonic corrosion detection. Refer to Work Card 20-90-03-106 (MTC).
- Comply with the instructions about anti-corrosion products for corrosion treatment. Refer to
Work Card 20-90-04-301 (MTC).
- Comply with the general method for restoring corroded surfaces. Refer to Work Card 20-90-04-401 (MTC).
- Comply with the specific treatment procedures for corrosion. Refer to Work Card 20-90-04-402 (MTC).
- Comply with the general information about repairs. Refer to Work Card 20-90-05-101 (MTC).
3.B. WORK STEPS
CAUTION
MAKE SURE THAT YOU PREVENT ALL POSSIBLE
FOD.
3.B.1. Preliminary steps
- Park the helicopter in a maintenance shop.
- Install the applicable access equipment.
- Remove the landing gear. Refer to Task 32-12-00, 4-1 (AMM).
3.B.2. Procedure
3.B.2.a. External inspection (Figure 3)
- Remove the landing gear fairing (not shown) from the rear crossbeam (a).
Refer to Task 32-12-00, 4-1 (AMM).
- Clean the outer side of the landing gear tubes (a), (c), (d) and (e) (Detail A, Figure 3).
Refer to Work Card 20-04-01-102 (MTC) and Work Card 20-04-01-402 (MTC).
NOTE 1
Zones B, C, D, E, F and M are included in the cleaning and
the inspection of the landing gear tubes (a), (c), (d) and (e).
- Do an external visual inspection of the landing gear tubes (a), (c), (d) and (e) to make sure that there are
no cracks and no corrosion.
. If you find at least one crack:
.. Contact Airbus Helicopters at the address that follows to get a technical solution:
... Airbus World: Technical Request Management https://airbusworld.helicopters.airbus.com
.. E-mail: support.technical-optional.ah@airbus.com
.. Fax: + 33 (0) 4 42 85 99 66
Revision 0 2022-02-15  Page 11/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
If you find any corrosion within zones C or E:
.. Disassemble the landing gear. Refer to Task 32-12-00, 4-2 (AMM).
.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).
• If you find corrosion only within zones B, D, For M:
.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).
• Then, in all cases, comply with paragraph 3.B.2.b.
3.B.2.b. Internal inspection (Figure 3)
- With the borescope (zz), examine the inner side of the landing gear tubes (a), (c), (d) and (e) for
corrosion and cracks. Refer to Detail A, Figure 3, and the criteria of Table 3.
NOTE 2
If only the internal inspection is to be done, removal of the
landing gear is not necessary.
NOTE 3
To examine zones E and D, make sure that the length of the
borescope (zz) is sufficient and the diameter is less or equal
to 8 mm (.098 in).
NOTE 4
To do the borescope inspection of the landing gear
tubes (a), (c), (d) and (e), you can remove the screws i) or
the blanking cap assembly (b) (Detail D, Figure 3). Refer to
the principle of Task 32-12-00, 4-2 (AMM).
NOTE 5
To do the borescope inspection of the landing gear tube (a),
you can remove the screws (k) (Detail D, Figure 3). Refer to
the principle of Task 32-12-00, 4-2 (AMM), if necessary.
NOTE 6
You can use the holes of the screws (not shown) at clamp
position F to do the borescope inspection in zones E and D,
it necessary.
Revision 0 2022-02-15  Page 12/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
- Clean the inner side of the landing gear tubes (a), (c), (d) and (e). Refer to Work Card 20-04-01-102 and
Work Card 20-04-01-402 (MTC), if necessary.
If you find at least one crack or leafing corrosion or exfoliant corrosion (Figures 1 and 2):
.. Contact Airbus Helicopters at the address that follows to get a technical solution:
... Airbus World: Technical Request Management https://airbusworld.helicopters.airbus.com
... E-mail: support.technical-optional.ah@airbus.com
... Fax: + 33 (0) 4 42 85 99 66
Figure 1  Figure 2
. If you find any corrosion within zones C or E:
.. Disassemble the landing gear. Refer to Task 32-12-00, 4-2 (AMM).
.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).
.. Comply with paragraph 3.B.2.c.
. If you find corrosion only within zones B, D, F or M:
.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).
.. Comply with paragraph 3.B.2.c.
. If you do not find external nor internal corrosion nor cracks:
.. Install the screws i) or the blanking cap assembly (b) or (1) and the screw (k).
Refer to Task 32-12-00, 4-2 (AMM) (Detail D, Figure 3).
.. Comply with paragraph 3.B.2.d.
Revision 0 2022-02-15  Page 13/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
3.B.2.c. Permitted criteria
- With the Ultrasonic thickness gauges Olympus 45MG (or equivalent) (yy) and Work Card 20-90-03-106
(MC), measure the remaining thickness of the landing gear tubes in the zones where you removed
corrosion.
NOTET
The measurement of the remaining thickness with ultrasonic
thickness gauges must usually be done on surfaces without
protection after a local sanding of the protections (not
applicable to a-scan device).
Device calibration can be done with:
- Step calibration block made of 2024 aluminum
or
- 2 different edges of landing gear tubes and a caliper.
NOTE 8
When you use the Ultrasonic thickness gauges
Olympus 45MG (or equivalent) (Vy), it is not necessary to
remove the paint to do the check of the thickness of the
landing gear tubes.
Revision 0 2022-02-15  Page 14/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
- Interpret the results as shown in Table 3:
Table 3
Zones  Location  Permitted criteria
Below the two half-bearings of the rear
crossbeam (a).
Make sure that there is a minimum thickness of
Over 100 mm (3.937 in.) inboard and 100 mm  7 mm (.275 in.).
(3.937 in.) outboard of the clamp
On the LH/RH fitting, in the rear crossbeam (a)
B1  fitting zone, (Detail B, Figure 4).
B2  On the LH/RH rear crossbeam (a), in the fitting
zone, (Detail B, Figure 4).
C1  On the LH/RH skid assemblies (c) and (e),
(Detail C, Figure 4).
On the fitting, in the junction zone of the LH/RH
C2  skid assemblies (c) and (e), (Detail C, Figure 4).
D  Zone of the LH/RH front footstep.
On the front crossbeam (d).
On the LH/RH skid assembly (c).
Below the half-bearings of the front
crossbeam (d).
F  From 100 mm (3.937 in.) outboard of the LH
clamp to 100 mm (3.937 in.) outboard of the RH
clamp.
Make sure that there is a minimum thickness of
3.4 mm (.133 in.).
Make sure that there is a minimum thickness of
4 mm (.157 in.).
Make sure that there is a minimum thickness of
2.3 mm (.090 in.).
Make sure that there is a minimum thickness of
2.3 mm (.090 in.).
Make sure that there is a minimum thickness of
2.4 mm (.094 in.).
Make sure that there is a minimum thickness of
2.3 mm (.090 in.).
Make sure that there is a minimum thickness of
1.9 mm (.075 in.).
Make sure that there is a minimum thickness of
2.9 mm (.114 in.).
NOTE 9
Criteria in ZONE E are the same for sleeved and assembled
landing gears.
- If the corrosion is not more than the criteria in Table 3:
. Comply with paragraph 3.B.2.d.
- If the corrosion is more than the criteria in Table 3:
• Contact Airbus Helicopters at the address below to get a technical solution:
.. Airbus World: Technical Request Management https://airbusworld.helicopters.airbus.com
.. E-mail: support.technical-optionnal.ah@airbus.com
.. Fax: + 33 (0) 4 42 85 99 66
Revision 0 2022-02-15  Page 15/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
3.B.2.d. Complementary actions
- Below the collar in zones M and F (Figure 3) and in the reworked zones, apply:
. Chemical conversion coating (Alodine 1200) (2). Refer to Work Card 20-90-05-401 (MTC).
. A double layer of chromate Primer P05 (3) and Primer P20 (4). Refer to
Work Card 20-04-05-101 (MTC).
- If the landing gear has not been disassembled and if rivets are loose and/or missing and if there is no
corrosion evidence, replace all the missing or loose rivets. Refer to Task 32-12-00, 8-2 (AMM).
- If the landing gear has been disassembled during the compliance of paragraph 3.B.2.a. or
paragraph 3.B.2.b., assemble the landing gear. Refer to Task 32-12-00, 4-2 (AMM), if necessary.
- If the landing gear fairing (not shown) has been removed during the compliance of the paragraph 3.B.2.a.,
install the landing gear fairing (not shown) on the rear crossbeam (not shown). Refer to
Task 32-12-00, 4-1 (AMM).
- Comply with paragraph 3.B.3. and 3.C.
3.B.3. Final steps
- Install the landing gear. Refer to Task 32-12-00, 4-1 (AMM).
- Remove the access equipment.
- Clean the work zones and the helicopter. Refer to Work Card 20-07-03-408 (MC).
- Set the helicopter to flight condition.
Revision 0 2022-02-15  Page 16/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record the full compliance with this ALERT SERVICE BULLETIN, with the revision number, in the
helicopter documents.
- Record the full compliance with this ALERT SERVICE BULLETIN (see IN 3785-1-00 for instructions):
QR code or hypertext link
NOTE 10
recording  compliance
ALERT SERVICE BULLETINS in the SB Insight tool does
not replace the recording in the helicopter documents.
ASB EC120-32A014
Revision 0 2022-02-15  Page 17/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 18 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
Identification of modifications on equipment or parts:
- Identify the landing gear refer to table below and Work Card 20-08-05-103 (MC).
Key Word  Old MP/N  New MP/N  MOD  Marking type
C321A2106102  C321A2106102  Indelible ink
+ ASB No. 32A014
C321A2501101
C321A2501101  Indelible ink
+ ASB No. 32A014
C321A2501102
C321A2501102  Indelible ink
+ ASB No. 32A014
Landing gear assembly
C321A2601051AA  + ASB No. 32A014  C321A2601051AA  Indelible ink
C321A2501051CA  C321A2501051CA  Indelible ink
+ ASB No. 32A014
C321A2501052  + ASB No. 32A014  C321A2501052  Indelible ink
C321A2104101  C321A2104101  Indelible ink
+ ASB No. 32A014
Front crossbeam  C321A2506101  C321A2506101  Indelible ink
+ ASB No. 32A014
C321A2506102  C321A2506102  Indelible ink
+ ASB No. 32A014
C321A2105101  + ASB No. 32A014  C321A2105101  Indelible ink
Rear crossbeam
C321A2507101  + ASB No. 32A014  C321A2507101  Indelible ink
C321A2107101
C321A2107101  Indelible ink
+ ASB No. 32A014
C321A2107102  C321A2107102  Indelible ink
+ ASB No. 32A014
LH skid assembly
C321A2503101  C321A2503101  Indelible ink
+ ASB No. 32A014
C321A2503102
C321A2503102  Indelible ink
+ ASB No. 32A014
C321A2108101  C321A2108101  Indelible ink
+ ASB No. 32A014
C321A2108102  C321A2108102  Indelible ink
+ ASB No. 32A014
RH skid assembly
C321A2502101  C321A2502101  Indelible ink
+ ASB No. 32A014
C321A2502102
C321A2502102  + ASB No. 32A014  Indelible ink
Revision 0  2022-02-15  Page 18/22
Revision 1  2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 19 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2022-02-15  Page 19/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 20 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
ZONE M
See Figure 4 BL
B See Figure 4
See Figure 4
ZONÉ E  D
ZONE D ZONE F  See Figure 4
- C
ZONE E
ZONE D
DI
PRE MOD  POST MOD
Back to paragraph 3.B.2.a.
Back to paragraph 3.B.2.b.
Back to paragraph 3.B.2.d.
Figure 3
Revision 0  2022-02-15  Page 20/22
Revision 1 2022-10-17  This document is available on the Internet: www.airb  icopters.com/techpub/

### Page 21 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
See Figure 3  See Figure 3
ZONE B2
ZONE B1
ZONE C2
ZONE C1
PRE MOD
See Figure 3  See Figure 3
ZONE B2
ZONE B1
ZONE C2
ZONE C1
POST MOD
Back to Figure 3
Back to Table 3
Figure 4
Revision 0 2022-02-15  Page 21/22
Revision 1 2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 22 (OCR)

AIRBUS  HELICOPTERS
No. EC120-32A014
4.  APPENDIX
RESPONSE FORM for ALERT SERVICE BULLETIN No. 32A014
"Inspection of the landing gear"
Complete the form and send it to:
- Airbus World: Technical Request Management: https://airbusworld.helicopters.airbus.com
- E-mail: support.technical-airframe.ah@airbus.com
- Fax: + 33 (0) 4 42 85 99 66
General information
H/C Type:
S/N:
Delivery Date:
FH:
Number of landings:
Replacement of landing gear parts
P/N  Designation  Reason for replacement  Date
Table of recording results
(photo)  Result  concerned  Part  (M, B1, B2, C1,  C2, D, E, F)  Location  Type  Damage size  (approx.)  after rework  Thickness  healthy zone near  Thickness in  the damage
Example  crossbeam  Front  junction collar  Below the  corrosion  Surface  20 mm X  30 mm  4.2 mm  5 mm
Date:  Signature:
Please make a copy of this page. The original form must stay in the ALERT SERVICE BULLETIN.
Revision 0 2022-02-15  Page 22/22
Revision 1  2022-10-17  This document is available on the Internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
