# Airbus Helicopters Alert Service Bulletin EC130-05A033

Copy: Airbus Helicopters ASB No. EC130-05A033 Rev 0 ("Airbus Helicopters ASB No. EC130-05A033 Rev 0"), 43 pages: PDF https://openairdocs.org/files/sha256/19/a9/19a95755f1d5286c8b48bea7dbd02afce0890c7e5c6976bba973960f29cafa77; text https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a033/file/19a95755f1d5.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0145, the docket of AD 2021-10-25. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC130-05A033
- Latest revision known: EC130-05A033, Revision 1, dated February 9, 2021 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a033

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a033/proposed.md).

## Text (43 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0145, the docket of AD 2021-10-25. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Civil versions: B4, T2
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
TIME LIMITS - MAINTENANCE CHECKS - Tail rotor
Inspection of the tail rotor blades
ATA: 64
For the attention of
Revision No.  Date of issue
Revision 0  2020-08-10
Summary:
The purpose of this ALERT SERVICE BULLETIN is to perform a crack inspection and a dimensional check for
each Tail Rotor Blade (TRB).
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
ASB EC130-05A033
Revision 0 2020-08-10  Page 1/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
EC130 helicopters equipped with TRBS MP/N 350A33-3002-02, 350A33-3002-03,
350A33-3002-04, 350A33-3002-05.
NOTE 1
TRBS MP/N 350A33-3004-xx, are not concerned by this
ALERT SERVICE BULLETIN.
NOTE 2
Refer to the Log Cards (FM) to identify the current
modification status of the helicopter. Machined TRBs MP/N
350A33-3004-xx, can also be identified visually as per IN
No. 2985-1-64.
1.A.2. Non-installed equipment or parts
TRBS MP/N 350A33-3002-02, 350A33-3002-03, 350A33-3002-04, 350A33-3002-05.
1.B. ASSOCIATED REQUIREMENTS
On receipt of Revision 0 of this ALERT SERVICE BULLETIN, make sure that Task 64-21-00,6-21 of AMM is
updated with the date code 2020.07.17 or later.
CAUTION
ON RECEIPT OF REVISION O OF THIS ALERT
SERVICE BULLETIN, EVERY COMPLIANCE WITH
TASK 64-21-00,6-21 OF THE AMM MUST BE
PERFORMED AS PER THE TASK UPDATED WITH
THE DATE CODE 2020.07.17 OR LATER.
Revision 0 2020-08-10  Page 2/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
1.C. REASON
An accident occurred on EC130 B4 in which the pilot reported sudden appearance of vibration followed by
the loss of Tail Rotor control. An emergency landing was performed.
Initial investigation has shown that one TRB was broken and three other TRBs had a small crack. All these
four cracks have been identified as progressive fatigue crack initiated from the water draining hole area, on
the trailing edge of the blade root.
The accident investigation is continuing and the root cause of the broken blade and the 3 cracked blades is
not known at this stage.
The laboratory examination has also evidenced some deviation from the original design geometry in the
drain hole area which are under analysis.
Consequently this ALERT SERVICE BULLETIN requests to inspect the affected parts at the drain hole
section, establishes criteria for replacement and remind the use of the last Work Card update for the limit
rework procedures.
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
- applying the following flowchart:
Identify the Flight hours (FH) of each
affected TRB.
The TRB has
Yes  less than  No
1,500 FH
since new
Perform a crack inspection  Perform a crack inspection
before TRB TSN reaches  within 50 FH from ASB
1,550 FH or within 12 months  issuance.
from ASB issuance.
Perform a crack inspection
Perform a dimensional check  every 20 FH until a
before TRB TSN reaches  dimensional check, to be
1,570 FH or within 12 months  performed within 165 FH or
from ASB issuance.  12 months from ASB
issuance.
Revision 0 2020-08-10  Page 3/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- applying different measures depending of the result of the crack inspection and the dimensional check:
. the TRBS may have to be replaced immediately in case of crack detection or depending on the
dimensional check result,
. or the TRBs may be maintained in service with a recurrent 20 FH crack inspection before replacement
within 1,000FH or 24 months (without exceeding the Service Life Limit of the TRB),
. or the TRBs may be maintained serviceable without further check.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
The work must be performed on the helicopter by the operator.
Helicopters/installed equipment or parts:
Comply with flowchart below:
Upon receipt of the Revision 0 of
this ALERT SERVICE BULLETIN
identify the Flight hours (FH) of
each affected TRB.
The TRB has
Apply flowchart 1  Yes  less than  1,500 FH  No  Apply flowchart 2.
since new?
Revision 0 2020-08-10  Page 4/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Flowchart 1
Comply with paragraphs 3.B.1., 3.B.2. and 3.B.5.
before TRB TSN reaches 1,550 FH or within 12
months (the first limit reached is applicable) from
receipt of the Revision 0 of this ALERT SERVICE
BULLETIN.
The TRB
is  Yes  Comply with
cracked?  paragraph 3.B.4.
No
Comply with paragraph 3.B.3. before TRB TSN
reaches 1,570 FH or within 12 months from
receipt of the Revision 0 of this ALERT SERVICE
BULLETIN
Apply flowchart 3.
Revision 0 2020-08-10  Page 5/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Flowchart 2
Comply with paragraphs
3.B.1. and 3.B.2. within 50
FH from receipt of the
Revision 0 of this ALERT
SERVICE BULLETIN.
Comply with  Yes  The TRB  is
paragraph 3.B.4.  cracked?
No
The TRB has
accumulated more than
Yes  165 FH or 12 months (the  first limit reached is
applicable) since receipt
of the Revision 0 of this
ALERT SERVICE
BULLETIN?
No
OR
Comply with paragraphs 3.B.1., 3.B.2.
Comply with paragraph  and 3.B.5. within 20 FH following the
З.В.З.  last compliance of the paragraph 3.B.2.
Apply flowchart 3.
Revision 0 2020-08-10  Page 6/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Flowchart 3
The TRB
is category  No
A?
Yes  is category  The TRB  No  The TRB is
B?  category C.
Compy with paragraph 3.B.5.
The TRB is not anymore
concerned by this ALERT
SERVICE BULLETIN.  Yes
Comply with paragraphs 3.B. 1.,
3.B.2. and 3.B.5. within 20 FH
tollowing the last compliance of the
paragraph 3.B.2.
The TRB
is  Yes  Comply with
cracked?  paragraph 3.B.4.
No
The TRB has accumulated
the Revision 0 of this ASB
No
without exceeding the
OR  Service Life Limit of the
blade or 24 months since the
receipt of the Revision 0 of
this ASB (the first limit
reached is applicable).
Comply with
paragraph 3.B.4.
Yes
Revision 0 2020-08-10  Page 7/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Non-installed equipment or parts:
The work must be performed on the non-installed equipment or parts by the operator.
Comply with paragraphs 3.B.2. to 3.B.4. except paragraphs 3.B.4.a. and 3.B.4.b. within 24 months from
receipt of Revision 0 of this ALERT SERVICE BULLETIN or before installation on the helicopter (the first limit
reached is applicable).
1.F. APPROVAL
Approval of modifications:
Not applicable.
OVED  Approval of this document:
The technical information contained in this Service Bulletin Revision 0 was approved on August 07, 2020
under the authority of EASA Organization Approval No. 21J.700 for civil version helicopters subject to an
Airworthiness Certificate.
1.G. MANPOWER
• For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following staff
qualification:
Qualification: - 1 Mechanical Technician for the crack inspection for compliance with paragraph 3.B.2.,
- 1 Mechanical Technician for the dimensional check for compliance with paragraph 3.B.3.a.,
- 2 Mechanical Technicians for the dimensional check for compliance with paragraphs 3.B.3.b.
and 3.B.3.c.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours: - 1 hour for one Mechanical Technician for compliance with paragraph 3.B.2.
- 3 hours for two Mechanical Technicians for compliance with paragraphs 3.B. 1. to
3.B.5. except 3.B.4.
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter
configuration.
Helicopter downtime is estimated at 1/2 day (excluding the time for replacing the TRBS) to check the TRBS.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
Revision 0 2020-08-10  Page 8/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
The following documents are required for compliance with this ALERT SERVICE BULLETIN.
Standard Practices Manual (MTC):
MTC: 20-04-01-102: Use of cleaning products on individual parts and on helicopters - Cleaning
MTC: 20-04-01-402: Cleaning of removed individual parts with liquid solvents - Cleaning
MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions
MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions
MTC: 20-02-09-101: Crack detection through dye-penetrant inspection: General - Crack detection
Aircraft Maintenance Manual (AMM):
AMM: 24-00-00,3-1: General Safety Instructions - Electrical Power Supply System - Electrical power
AMM: 60-00-00,3-2: General Safety Instructions - Critical Parts - General - Mechanics Systems
AMM: 64-21-00,4-3: Disassembly - Tail Rotor Hub - Tail Rotor Hub
AMM: 64-21-00,4-4: Assembly - Tail Rotor Hub - Tail Rotor Hub
AMM: 64-21-00,6-21: Visual Inspection Criteria - Tail Rotor Blade Assembly - Tail Rotor Hub - Inspection
Check
Information Notice (IN):
IN: 2985-1-64: TAIL ROTOR - Entry into service of a new tail rotor blade definition (POST MOD 07-6610)
IN: 3447-1-00: GENERAL - Introduction of the digital Service Bulletin reporting service R-TEX
1.L. OTHER AFFECTED PUBLICATIONS
Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
Revision 0 2020-08-10  Page 9/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For any information on the price of modification kits and/or components, contact the Airbus Helicopters
Network Sales and Customer Relations Department.
Availability
Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's
request.
Procurement
Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters
Etablissement de Marignane
Direction des Ventes et Relation Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to modify.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
Not applicable.
Revision 0 2020-08-10  Page 10/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Equipment or parts to be ordered separately:
Key Word  Qty  New P/N  Item  Old
P/N  →→  Instruction
Tail Rotor Blade  ALD  350A33-3002-02  1
(TRB)
Ou
Tail Rotor Blade  ALD  350A33-3002-03  2
(TRB)
Ou
Tail Rotor Blade  (TRB)  ALD  350A33-3002-04  Ou  350A33-3002-02  350A33-3002-03  or  Discard if  category  B or C.
Tail Rotor Blade  (TRB)  ALD  350A33-3002-05  4  350A33-3002-04  or  Return as per  Paragraph
Ou  350A33-3002-05  or  If cracked  2.D
Tail Rotor Blade  ALD  350A33-3004-00  5
(TRB)
Ou
Tail Rotor Blade  ALD  350A33-3004-01  6
(TRB)
Revision 0 2020-08-10  Page 11/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Consumables to be ordered separately:
As per Work Cards and Task indicated in this ALERT SERVICE BULLETIN.
Consumables can be ordered separately from the following companies:
Aviatec Global Aviation
Website: www.aviatec.net
Telephone: +33 1.34.46.45.24 or +49 4193.8803.630
Fax: +33 1.34.46.45.26 or +49 4193.8803.699
AOG: +49 4193.8803.660
AOG email: aog@aviatec.aero
BDSI
Website: www.boeingdistribution.com
Telephone: +1.305.925.2600
Fax: +1.305.507.7191
AOG: +1.305.471.8888
AOG email: AOGdesk@Boeingdistribution.com
Gaches Chimie
Website: www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
Special tools:
As per Work Cards and Task indicated in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  Tool P/N or equivalent  Item
Smartphone  Commercial P/N
Digital camera  Commercial P/N
Red color marker  Commercial P/N
Computer  Commercial P/N  ww
Steel ruler  Commercial P/N  VV
Light  Commercial P/N  uu
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Return the cracked TRBs to the following address:
Airbus Helicopters
Aéroport Marseille Provence
RETEX Factory -
Gare d'arrivée MAH09MGA2 - B1- LES BORIES
SOUS-SOL - ARRIVEE
13 725 Marignane CEDEX
France
Revision 0 2020-08-10  Page 12/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
3. ACCOMPLISHMENT INSTRUCTIONS
3.А. GENERAL
- As per Work Card 20-04-01-102 (MTC), read and comply with the use of cleaning products on individual
parts and on helicopters.
- As per Task 24-00-00,3-1 (AMM), read and comply with the General Safety Instructions.
- As per Task 60-00-00,3-2 (AMM), read and comply with the General Safety Instructions.
3.B. WORK STEPS
3.B.1. Preliminary steps
- Disconnect all the electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Install the access equipment.
- Clean the TRBs in the hole area as per Work Card 20-04-01-402 (MTC) (Figure 1).
3.B.2. Crack inspection of the TRBS
- Make sure that there are no cracks on each TRB (a) in the hole area as per Figure 1 and perform a dye
penetrant inspection as per Work Card 20-02-09-101 (MTC), or in accordance with Standards detailed in
ASTM E1417.
- Continue to comply with paragraph 1.E.2.
Revision 0 2020-08-10  Page 13/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
3.B.3. Dimensional check of the TRBs
- The dimensional check procedure consists in checking the three following dimensions:
. Distance from the hole Axis to the Shoulder (DAS),
• RIB Thickness (RIBT),
• Remaining Thickness (RT).
Distance  Rib thickness
from hole axis
to shoulder
Minimum
Hole axis  remaining
section  thickness
Center of the
draining hole
Location of the three dimensions to check Figure 2
- There are three different means of measurement which are listed in the order of application. If a mean is
not accessible or not conclusive, use the next one in the following order:
• 1. Smartphone application.
. 2. PowerPoint method.
• 3. Contact customer support with a specific procedure.
NOTE 1
These means are detailed in the following paragraphs:
3.B.3.a., 3.B.3.b. and 3.B.3.c.
- Thanks to these means, you must check one criterion on each three previous dimensions:
. The DAS is less than or equal to 4.7 mm (0.185 in). This distance corresponds to the distance between
the center of the drain hole and the shoulder without taking into account the radius (R = 1 mm) of the
shoulder as per Figure 3 below:
Distance
from hole axis
, Shoulder  to shoulder
Drain
hole center
Radius R = 1 mm
Figure 3
Revision 0 2020-08-10  Page 14/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
. The RIBT is more than or equal to 2.2 mm (0.086 in). at the level of the hole center, as described in
Figure 2.
. The RT is more than or equal to 0.2 mm (0.008 in). This distance corresponds to the minimum distance
between the rib edge and the drain hole circle. The chamfer of the drain hole must not be taken into
account (cf. Figure 4 below).
Hole axis  Minimum
section  remaining
thickness
Figure 4
- If the remaining thickness is below 0.2 mm (0.008 in), you must determine if the measurement is below or
above 0.1 mm (0.004 in).
- These three criteria must be checked.
Revision 0 2020-08-10  Page 15/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
3.B.3.a. Measurement of the TRBs with a smartphone (available for Android only)
Purpose is to determine if TRB is in category A or not.
- Download the cell phone app on a smartphone (zz) by following the link below:
app for Android
- Read and comply with the instructions given in Appendix 4.B. to use the cell phone app.
- Measure the TRBs using the smartphone (zz).
- Interpret the results as per Appendix 4.B. and paragraph 3.B.3.d.
- If in doubt or not category A, comply with paragraph 3.B.3.b.
3.B.3.b. Measurement of the TRBs with Powerpoint method
Purpose is to determine if TRB is in category A or B or C.
- Comply with the work steps described in Appendix 4.C.
- Sign in to the "TIPI" website with the computer (ww) by following the link below:
www.airbushelicopters.com/techpub
- Download the powerpoint file on the computer (ww) by following the link below:
measurement tool mm (millimeter measurement unit)
or
measurement tool_in (inch measurement unit)
- Comply with the work steps described in the video which is available by following the
link "dailymotion" or QR-Code or the link "TIPI" below:
https://www.dailymotion.com/video/koSCH0bWIMZ1IDwc8OD
video on TIP
Revision 0 2020-08-10  Page 16/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- Interpret the results as per paragraph 3.B.3.d.
- If in doubt, comply with paragraph 3.B.3.c.
3.B.3.c. Measurement of the TRBs - backup solution
NOTE 2
Refer to NOTES 4, 5, 6 and 7 as per Appendix 4.C.
- Take a picture of each TRB with a smartphone (zz) or a digital camera (yy) as per work steps dedicated to
picture of TRBS described in the video by following the link "dailymotion" or QR-Code or the link "TIPI"
below:
https://www.dailymotion.com/video/koSCH0bWIMZ1IDwc8OD
video on TIPI
- Send the pictures for measurement to the following address:
. with WebTEK access:
.. create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
.. select the TE business domain: "ASB Fenestron Blade",
.. the TE title must contain at least the following key words "ASB 05A033 ok" if the ten blades are in
good condition or "ASB 05A033 Not ok" if at least one blade status is questionable,
. without WebTEK access:
.. to the following address: technicalsupport.helicopters@airbus.com,
- Comply with paragraph 3.B.3.d. following receipt of measurement performed by backup solution.
Revision 0 2020-08-10  Page 17/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
3.B.3.d. Interpretation of the results
The
RT
No  is more than  Yes
0.1 mm
(0.004 in)?
The TRB  The RT is
is  more than or
category  No  equal to 0.2  Yes
C  mm (0.008 in)?
The RIBT is
more than or
No  equal to 2.2  Yes
mm (0.086 in)?
The DAS is
less than or
No  equal to 4.7
mm (0.185 in)?
The TRB
is  Yes
category
B
The TRB
is
category
Revision 0 2020-08-10  Page 18/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- If the TRB is category "A":
• make a copy of the Tail Rotor Hub (TRH) log card with legible TRBS information.
. return the TRH log card:
.. with WebTEK access:
... create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
... select the TE business domain: "ASB Fenestron Blade",
.. TE title must contain at least the following key words "ASB 05A033 ok",
.. without WebTEK access:
... to the following address: technica support.  helicopters@airbus.com,
. continue to comply with paragraph 1.E.2.
- If the TRB is category "B" or "C":
. complete and return the response sheet in Appendix 4.A.:
.. with WebTEK access:
... create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
.. select the TE business domain: "ASB Fenestron Blade",
... TE title must contain at least the following key words "ASB 05A033 Not ok",
without WebTEK access:
... to the following address: technicalsupport.helicopters@airbus.com,
. continue to comply with paragraph 1.E.2.
3.B.4. Replacement of the TRB
3.B.4.a. For installed equipment or parts (in case of crack)
- Remove the TRB (a) (not shown) as per Task 64-21-00,4-3 (AMM).
- Complete and return the response sheet in Appendix 4.A.:
.. with WebTEK access:
... create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
select the TE business domain: "ASB Fenestron Blade",
.. the TE title must contain at least the following key words "ASB 05A033 Not ok",
. without WebTEK access:
. to the following address: technicalsupport.helicopters@airbus.com.
- Return the TRB (a) (not shown) as per paragraph 2.D.
- Install an airworthy TRB (1) or (2) or (3) or (4) or (5) or (6) (not shown) as per Task 64-21-00,4-4 (AMM).
3.B.4.b. For installed equipment or parts (in case of category B or C)
- Remove the TRB (a) (not shown) as per Task 64-21-00,4-3 (AMM).
- Complete and return the response sheet in Appendix 4.A.:
.. with WebTEK access:
... create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
• select the TE business domain: "ASB Fenestron Blade",
... the TE title must contain at least the following key words "ASB 05A033 Not ok",
. without WebTEK access:
... to the following address: technicalsupport.helicopters@airbus.com.
- Install an airworthy TRB (1) or (2) or (3) or (4) or (5) or (6) (not shown) as per Task 64-21-00, 4-4 (AMM).
- Return the TRB (a) (not shown) as per paragraph 2.D
Revision 0 2020-08-10  Page 19/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
3.B.4.c. For non-installed equipment or parts (in case of a crack)
- Complete and return the response sheet in Appendix 4.A.:
.. with WebTEK access:
... create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
.. select the TE business domain: "ASB Fenestron Blade",
.. the TE title must contain at least the following key words "ASB 05A033 Not ok",
.. without WebTEK access:
... to the following address: technicalsupport.helicopters@airbus.com.
- Return the TRB (a) (not shown) as per paragraph 2.D.
3.B.4.d. For non-installed equipment or parts (in case of category B or C)
- Complete and return the response sheet in Appendix 4.A.:
.. with WebTEK access:
.. create a Technical Event (TE) on WebTEK: https://keycopter.airbushelicopters.com,
select the TE business domain: "ASB Fenestron Blade"
.. the TE title must contain at least the following key words "ASB 05A033 Not ok",
.. without WebTEK access:
... to the following address: technicalsupport.helicopters@airbus.com,
- Discard the TRB (a) (not shown).
3.B.5. Final steps
- Perform an appearance check on the helicopter after inspection or repair as per
Work Card 20-07-03-408 (MTC).
- Connect all the electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Remove the access equipment.
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record full compliance with this ALERT SERVICE BULLETIN, with the revision number, in the
Log Card (FM).  " complice with is ALERT SERVICE BULLETIN a per In
- Please confirm compliance with this ALERT SERVICE BULLETIN as per Information Notice No. 3447-1-00:
QR-Code or hypertext link
NOTE 3
The  recording of compliance with ALERT SERVICE
BULLETINS in the R-Tex tool does not replace the recording
in the helicopter documents.
ASB EC130-05A033
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2020-08-10  Page 20/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 21 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
ÇA
Dye penetrant area
LH helicopter side
C or D
Hole area
Return to paragraph 3.B.1.  Figure 1
Revision 0 2020-08-10  Page 21/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 22 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
4. APPENDIX
4.A. APPENDIX: Information sheet for category B and/or C TRB
ALERT SERVICE BULLETIN Response Form
No. 05A033
Complete the form and return it to:
Airbus Helicopters - Etablissement de Marignane
Customer Support
https://keycopter.airbushelicopters.com
Keep a completed copy of this response sheet in the Aircraft Log Book.
Date:
Customer (Name):
Helicopter:
Version:
Serial Number:
Total flight hours:
Crack inspection result and dimensional check (next page):
NOTA: one line in the chart per blade
Revision 0 2020-08-10  Page 22/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 23 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
ALERT SERVICE BULLETIN Response Form
No. 05A033
Tail Rotor Hub (TRH)  Tail Rotor Blade (TRB)
Visible/Not visible  Distance from the hole axis  to the shoulder (DAS) 4.7 mm  (0.185 in) max criteria  Ok/Nok/N/A  Rib thickness (RIBT) 2.2 mm  (0.086 in) mini criteria  Ok/Nok/N/A  Minimum remaining  thickness(RT) 0.2 mm  (0.008 in) mini criteria  Ok/Nok/N/A  Minimum remaining  thickness (RT) 0.1 mm  (0.004 in) mini criteria  Ok/Nok/N/A  Status
Inspection  Number  Part  Number  Serial  TSN  Number  Part  Number  Serial  TSN  Crack  A or B or
date  (FH)  (FH)  C or
(MP/N)  (S/N)  (MP/N)  (S/N)  cracked
Remarks:
Date:  Signature:
Please make a copy of this page. The original form must remain in the ALERT SERVICE BULLETIN.
Revision 0 2020-08-10  Page 23/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 24 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
4.B. APPENDIX: Manual to use the cell phone app
Introduction
This document is made to provide information about the A.I.R Blade® application: how to install the app and
turthermore how to use the services and functions available
A..R Blade (Artificial Image Recognition for Blade) is an android App for smartphone (not for tablet) made to
support the EC130 ASB Tail Rotor blades check.
A.I.R Blade
Load
Save
Demo
ELICO TUS
Zoom  Min RT  Scan
RIB T
DAS
Its purpose is to automatically display on a picture of the blade the dimensions to be checked. The three
dimensions are:
• Minimum remaining thickness [MIN RT].
• RIB Thickness [RIB T].
• Distance hole axis to shoulder [DAS].
Revision 0 2020-08-10  Page 24/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 25 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Location of the 3 dimensions to control
Distance  Rib thicknes
from hole axis
to shoulder
Minimum
Hole axis  remaining
section  thickness
Center of the
draining hole
Setup
Preliminary checks:
- Check that you have enough space on your smartphone to install the application.
- If you have a previous version, uninstall it before install a new version.
To install the app, follow this procedure:
• Transfer the apk file on a Smartphone. NB: It is advised to store it on a specific folder to find the file
more easily.
• On your smartphone, open your file manager app. Find the apk A.I.R Blade file where you stored it,
then click on it to launch the automatic installation.
• The system might tell you that you are not allowed to install it, in this case, follow this procedure:
• Click on settings when you have the following message: "For your security, your
phone is not allowed to install unknown apps from this sources).
• Click on the "Allow from this source button".
• Then go back or use the arrow button on the top left corner.
Revision 0 2020-08-10  Page 25/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 26 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Storage  Install unknown apps
Internal shared storage › documents › Airblade ›  Allow from this source
AIRBladeDRAFT
/rems 1 771s/20 14.03  Your phone and personal data are more vulnerable to
attack by unknown apps. By installing apps from this
AIRBlade  source, you agree that you are responsible for any
damage to your phone or loss of data that may result
7 items | 6/30/20 09:44  from their use.
AIRBlade.apk
43.17MB | 7/21/20 13:13
File Manager
For your security, your phone is not
allowed to install unknown apps from
this source.
CANCEL  SETTINGS
After the application installation, you can click on 'open' to launch it.
Revision 0 2020-08-10  Page 26/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 27 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Welcome page
A.I.R Blade
Load
Save  Save Picture
Demo  Demo Video
Chart
FlowChart decision for
blade category
AIRBUS
IELICOPTERS  TAR
Zoom  Zoom  Min RT  Scan  the drain hole of  SCAN To detect
function  RIB T  the H130 Blade
DAS
Remote position controller fo RIB T
Dimensions  (only)
to be checked
Revision 0 _ 2020-08-10  Page 27/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 28 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Detection
1. Click on the scan button.
2.  The app gives you several recommendations to take a picture:
The handle of the blade must visible and at the top of the screen
Drain hole must be clear, use the focus, by tapping on the hole, to obtain a clear picture
Use at least zoom 3X
Disable the flash
In accordance with these recommendations, you should get picture like this:
3. Compliantly with these recommendations, take the picture of the blade drain hole.
Revision 0 2020-08-10  Page 28/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 29 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
4. The app will scan the picture to find the blade drain hole (see picture below), it display you the
circle that it found:
IR Blade
6.0 mm
1 hole found  Scan
Is this the blade drain hole?
No  Yes  Cancel
Several detection situations are possible:
a. No hole found > take the picture again.
b. One hole found > Check if it's the drain hole of the blade > Click on yes.
C.  Multiple holes are found > Select the one corresponding to the drain hole of the blade
by clicking yes or no.
Revision 0 2020-08-10  Page 29/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 30 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Measurements
The area to be checked is:
Perform all the measurements as describe below, record them and refer to the following flowchart:
NO  RT > 0.2 mm  YES
(0.0079 inch)
NO  RIBT > 2.2 mm  YES
(0.087 inch)
YES
DAS < 4.7 mm
NO  (0.185 inch)
Perform measurement of the
TRBs with a computer (PPT
method) in accordance with the  Blade category A
paragraph 3.B.3.b.  Refer to the paragraph 3.B.3.d.
Revision 0 2020-08-10  Page 30/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 31 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
MIN RT: Minimum remaining thickness (defined as RT in paragraph 3.B.3.)
The minimum remaining thickness [Min RT] correspond to:
Hole axis
section  Minimum
remaining
thickness
For the Minimum remaining thickness, tap on Min RT:
IR Blade
2mm (0.00
Zoom out  Min RT  Display the MIN RT
DAS
Revision 0 2020-08-10  Page 31/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 32 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
A yellow circle representing the hole radius + 0.2 mm (0.008 in.) centered on the hole center will appear. This circle
will allow you to evaluate if the Minimum remaining thickness, is more than or equal to 0.2 mm (0.008 in.).
Min RT > 0.2mm (0.0079 in) if the yellow circle is contained within the RIB Thickness, See the example below:
OK  NOT OK
Radi  . 2mm  Radius +0.2mm
Revision 0 2020-08-10  Page 32/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 33 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
RIB T: RIB Thickness
The RIB Thickness correspond to:
Rib thickness
Hole axis
section
For the RIB Thickness, tap on RIB T:
Zoom out  Min RT  Scan
DAS
Use the Pad to move
the magenta circle
A magenta circle with radius 2.2 mm (0.086 in) and a position remote controller will appear.
This remote controller will permit you to move the circle to evaluate if the RIB Thickness is more than or equal to
2.2 mm (0.086 in).
Revision 0 2020-08-10  Page 33/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 34 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
RIB T > 2.2mm (0.087 in) if the magenta circle is contained within the RIB Thickness. Move the magenta circle
using the controller to fit it within the RIB Thickness. See the example below:
OK  NOT OK
Diameteri  2.2mm
veter 2.2mm
Revision 0 2020-08-10  Page 34/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 35 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
DAS: Distance hole axis to shoulder
The distance hole axis to shoulder correspond to:
Location of the 3 dimensions to control
Hole axis
Center of the
draining hole
To display the distance hole axis to shoulder, click on DAS:
AIR Blade
6.0 mm
Zoom out  Min RT  Scan
• Click to display
Revision 0 2020-08-10  Page 35/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 36 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
A green circle with radius 4.7 mm (0.185 in), centred on the hole, will appear allowing you to evaluate if the
distance hole axis to shoulder is less than or equal to 4.7 mm (0.185 in).
DAS < 4.7 mm (0.185 in  † the si  oulder edge is contained within the circle as the example below:
OK  NOT OK
Distance hole/sh
Distar
Revision 0 2020-08-10  Page 36/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 37 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Picture Saving
You can save the pictures with the "Save" button, at the top right corner of the app.
→ Save pictures
Put the blade serial number as the name:
Save
Demo
Enter optional Filename Prefix (alphanumeric)
XXXX
Cancel  Confirm  Confirm to save
Enter the
XXXX
serial number
XXXX  XXXL
b
?123
The picture are stored in the folder "AIRBlade" in the path following /DCIM/AIRBlade.
Revision 0 2020-08-10  Page 37/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 38 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
4.C.  PPENDIX: Manual to use PowerPoint method
- When the smartphone application is not available or if one of the dimensions is not within the criteria, you
can use the PowerPoint method.
- Equipment:
1 smartphone (zz) (use one as modern as possible to obtain the best picture quality)
1 steel ruler (vv) (mm or inch)
• 1 light (uu) or a second smartphone (zz) for lighting
- Remark: if you use a ruler in mm, you must use the PowerPoint in mm and if you use a ruler in inches,
you mustuse the PowerPoint in Inches.
- Number of people: 2
. 1 for taking pictures
• 1 for positioning the ruler and the grazing light
PowerPoint procedure:
Actions of the 1st step: Pictures
1. Push the left-hand yaw pedal (¾ travel) to turn the blade pitch and to ease picture taking with the
appropriate angle.
2. Clean the tail rotor blades.
3. Before starting, bond some tapes to the blades with the numbers from 1 to 10 to make picture
management in the following steps easier. This number must be visible on the picture as described on
the video.
4. Position the steel ruler against the rib of the blade as seen in the video to obtain a dimensional jig.
Be careful to put the ruler angle as near the rib plane on which the hole is drilled and to the hole as
possible (see Note 4 - 2nd point). Be careful to set the ruler parallel to the rib plane (or perpendicular to
the smartphone view).
5. Add a grazing light from the right-hand side of the fenestron to highlight the rib edges.
6. Position the smartphone with the 2nd person as seen in the video. Put the smartphone against the
previous blade (cf. video) to improve stability and limit the risks of blurred picture.
Depending on the location of your smartphone lens, it will be more appropriate to take a horizontal
picture or vertical picture to place the lens in the blade rib alignment.
7. Tilt your smartphone parallel to the blade until you obtain a picture perpendicular to the blade shoulder
(cf. Note 4 - 4th point).
8. You must obtain first a clear image on your screen, then zoom in until reaching a picture such as in the
video or the correct pictures in the following notes.
9. Take the picture.
10. Turn the tail rotor clockwise and start again from the action No. 4 on the second blade and after for all
Revision 0 2020-08-10  Page 38/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 39 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
Actions of the 2nd step: PowerPoint method
1. Transfer the 10 pictures from your smartphone to the computer and rename it from 1 to 10.
2. Open the PowerPoint file in mm or Inches depending on the ruler choice.
3. Look at the examples on the 3 dimensions on the PowerPoint.
4. Insert all pictures on the file, make sure that the tape on the picture is the same than the blade number in
the PowerPoint.
5. Activate gridlines to make alignments easier and tick the boxes on the picture properties to keep the
original proportions of the picture.
You must only perform it once for the complete file (not for each picture).
6. Turn the picture until the ruler lines are vertical.
7. Crop the picture to keep only visible the ruler, the hole and the shoulder of the blade (see the video to
find the size needed before the zoom in step).
8. Move the calibration jig in front of the picture (or send backward the picture as described in the video).
9. Adjust the size of the picture using the PowerPoint ruler (top right-hand corner) until the calibration jig
corresponds to the steel ruler lines spacing.
10. Criteria assessment:
o Distance from the hole Axis to the Shoulder (DAS) ≤ 4.7 mm (0.185 in):
Place the circle of your green jig to match the circle of the drain hole. Then, check if the distance on
the picture is below 4.7 mm jig as illustrated in the PowerPoint example.
o RIB Thickness (RIBT) ≥ 2.2 mm (0.086 in):
Place one of the two ends of the pink jig on one rib edge and check if the rib still goes beyond the
other end as illustrated in the PowerPoint example.
o Minimum remaining Thickness (RT) ≥ 0.2 mm (0.008 in):
As there is never complete alignment of the drain hole, choose the side with the minimum remaining
thickness. Then, place the internal circle of the yellow jig to match the drain hole circle. Focus on the
side where you measure the remaining thickness. The thickness of the jig is 0.2 mm. If the rib edge is
visible outside the jig, it means that the remaining thickness is greater than 0.2 mm. If not, the edge
is inside the jig and the remaining thickness is less than 0.2 mm. If the chamfer of the drain hole
intersects the rib edge, draw a line as explained in Note 3 below.
If the remaining thickness is below 0.2 mm, perform the same operation with the red jig at
0.1 mm thickness.
NOTE 4
To optimize the quality of the measurements, make sure:
- To change the orientation of the blades using the yaw pedals so
that the drain hole center is aligned with the smartphone lens.
Both TRB sides must be visible as follows.
LEL
EEL
Non pivoted blade: NOK  Pivoted blade: OK
Revision 0 2020-08-10  Page 39/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 40 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- to position the steel ruler as near the drain hole as possible, and
in the same plane,
Not possible
to see the
ruler and the
hole after
zoom in  *spuze
Incorrect ruler location: NOK  Correct ruler location: OK
Revision 0 2020-08-10  Page 40/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 41 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- to set the ruler parallel to the blade plane on which the hole is
drilled,
- to keep the smartphone parallel to the blade to see the shoulder
as a line and not a plane. On the left-hand picture below, the
distance from the hole axis to the shoulder will be completely
incorrect,
Reference
line
6
FEL
Non shifted blade: NOK  Shifted blade : OK
- to put the smartphone against the previous blade to make sure
that it is stable during picture taking and thus to avoid blurred
pictures,
ww
6  *spuze
Blurred picture: NOK  Clear picture: OK
Revision 0 2020-08-10  Page 41/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 42 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
- to use a grazing light to be able to detect rib edges,
No grazing light: NOK  Too much grazing light: NOK  Correct grazing light to detect
edges : OK
- to use the zoom after setting the focus on the picture.
NOTE 5
To make sure to keep a good tracking of pictures with the
corresponding blades, make sure:
- to identify by drawing a red mark on the cover aligned with
the first blade to photograph,
- to always turn the tail rotor clockwise when you are on the
left-hand side,
- to rename the pictures from 1 to 10 before opening the
PowerPoint.
NOTE 6
For particular blades, when the drain hole chamfer overlaps
the rib edge on one side, make sure to identify the missing
edge by drawing a line linking both sides within the
PowerPoint as described below:
Revision 0 2020-08-10  Page 42/43
This document is available on the Internet: www.airbushelicopters.com/techpub

### Page 43 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-05A033
NOTE 7
To perform an  accurate measurement with the PowerPoint
method, make sure:
- to take time to calibrate accurately the picture dimensions using
the ruler and the red calibration jig,
- after inserting the picture in the PowerPoint, to force the picture
size to keep the original proportions,
- after each picture measurement, to check if the calibration jig size
and the measurement jigs size still match the jig box pattern (see
pictures below).
Blade N°1  not compliant to  Fill-out if TRB is  OK if distance hole axis to shoulder ≤ 4,7mm  OK if rib thickness ≥ 2,2mm  Measurement
the ASB criteria  OK if remai  Ss ≥ 0,2mm  jies box
2,2mm mini  Calibration:
Calibration:  3×1mm
4,7mm max  3×1mm
2,2mm mini
4.7mm maxi
O
0,1mm mini
Blade N°1  Fill-out if TRB is  not compliant to  OK if distance hole axis to shoulder ≤ 4,7mm  OK if rib thickness ≥ 2,2mm  Measurement
the ASB criteria  OK if remainind th  ess ≥ 0,2mm  jigs box
Calibration:
3×1mm
2,2mm mir
4.7mm maxi  0,2mm mini
0,1mm mini  O
0,1mp mini
Revision 0 2020-08-10  Page 43/43
This document is available on the Internet: www.airbush  licopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
