# Airbus Helicopters Alert Service Bulletin EC130-05A040

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- No revision named ("Airbus Helicopters Alert Service Bulletin EC130-05A040"), 22 pages: PDF https://openairdocs.org/files/sha256/94/b9/94b905b4b2730b2a80ed0ac47206718f0181fd78f8b128f8e75c0070e9e9e13a; text https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a040/file/94b905b4b273.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-5032, the docket of AD 2026-12-03. Not covered by OpenAirDocs’ CC0 dedication.
- No revision named ("Airbus Helicopters Alert Service Bulletin EC130-05A040 Rev 0"), 22 pages: PDF https://openairdocs.org/files/sha256/03/2e/032e81e62ed2a3789fb4bbf940a82400fd3a58c9b4011196ee56d39381a06293; text https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a040/file/032e81e62ed2.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2024-2419, the docket of AD 2025-06-04. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC130-05A040
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec130-05a040

## Text (22 pages)

No revision named, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-5032, the docket of AD 2026-12-03. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
Civil version(s): B4, T2
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
TIME LIMITS - MAINTENANCE CHECKS - Main rotor drive
Check of the Main Gear Box (MGB) bevel wheel
ATA: 63
For the attention of
Revision No.  Date of issue
Revision 0  2023-01-25
Summary:
The purpose of this ALERT SERVICE BULLETIN is to improve the detection of particles in the MGB by introduction
of a periodic visual inspection of the bevel wheel or in case of particles detection during scheduled check of the
Magnetic Plugs (MP) of the MGB.
Compliance:
It is mandatory to comply with this ALERT SERVICE BULLETIN.
Revision 0  2023-01-25  Page 1/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters EC130 version T2 and B4 that have MGB planet gears bearing MP/N 350A32-1082-03 or
MP/N 350A32-1114-00.
NOTE
Refer to the Log Card (FM) of the MGB to identify the current
notification status of the equipment.
1.A.2. Non-installed equipment or parts
MGB that have planet gears bearing MP/N 350A32-1082-03 or MP/N 350A32-1114-00.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Airbus Helicopters is proactively reassessing its maintenance policy with respect to particle detection in MGBs
for its entire product range. These analyses have been expanded to include the MGB of the
Ecureuil family.
As a precautionary measure and to enhance safety of the product, the purpose of this
ALERT SERVICE BULLETIN is to improve the detection of particles in the MGB by introduction of a periodic
visual inspection of the bevel wheel or in case of particles detection during scheduled check of the
Magnetic Plugs (MP) of the MGB.
1.D. DESCRIPTION
The ALERT SERVICE BULLETIN includes the work steps that follow:
- Do a visual inspection of the MGB bevel wheel with a boroscope.
- Make sure that there are no particles on the MGB bevel wheel.
- If necessary, collect the particles on the MGB bevel wheel with a vacuum pump.
- Analyze the results, refer to the flow chart.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
Revision 0 2023-01-25  Page 2/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
1.E.2. Compliance in service
Helicopters/installed equipment or parts:
The operator must do the work on the helicopter.
Comply with paragraph 3. of this ALERT SERVICE BULLETIN. Refer to Table No. 1:
Table No.1
Helicopter configuration  Compliance time  Periodicity
MGB that have planet gears bearing  MP/N 350A32-1082-03 or  Not more than 660 Flight Hours (FH) after
MP/N 350A32-1114-00  you received this
installed on helicopters  ALERT SERVICE BULLETIN. (Refer to the  issue date on the page footer) or in case of
MGB that have planet gears bearing  MP/N 350A32-1082-03  EC130 version B4  particles characterized as scale, flake or  splinter found on a MGB magnetic plug  Every 660 FH
during compliance with
installed on helicopters  EC130 version T2  Task 60-00-00,6-2A (AMM).
Not more than 330 FH after you received
MGB that have planet gears bearing  this ALERT SERVICE BULLETIN. (Refer to  the issue date on the page footer) or in
MP/N 350A32-1114-00
installed on helicopters  flake or splinter found on a MGB magnetic  case of particles characterized as scale,  Every 330 FH
EC130 version T2
plug during compliance with
Task 60-00-00,6-2A (AMM).
Non-installed equipment or parts:
For non-installed MGB or when you install a MGB on helicopter:
- If the MGB is more or equal to 330 FH since the last Time Since Overhaul (TSO) and since Time since New
(TSN) and since last boroscopic inspection of the bevel wheel:
• Comply with paragraph 3. before installation of the MGB on the helicopter.
- If the MGB is less than 330 FH since the last Time Since Overhaul (TSO) or since Time since New (TSN) or
since last boroscopic inspection of the bevel wheel:
. No action is required immediately.
. After you install the MGB on the helicopter:
.. Comply with paragraph 3. before you reach 330 FH.
.. Refer to table No.1 for periodicity (installed equipment or parts).
1.F. APPROVAL
The technical content of this document is approved under the authority of the Design Organization Approval
ref. EASA. 21J.700.
Revision 0 2023-01-25  Page 3/22
Ce document est disponible sur internet : www.airbushe  elicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
1.G. MANPOWER
' Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this
qualifications:
Visual inspection of the MGB bevel wheel (paragraph 3.B.2.):
Qualification: 2 Mechanical Technicians or 1 Mechanical Technician (for the inspection) and 1 crew member
(to turn tail rotor).
Analysis of the results (paragraph 3.B.4.):
Qualification: 1 Mechanical Technician
The man-hours are an estimate given for information only and for a standard helicopter configuration.
Visual inspection of the MGB bevel wheel (paragraph 3.B.2.):
Estimated Man-hours: an half hour for two Mechanical Technicians.
Collect of the particles (paragraph 3.B.3.):
Estimated Man-hours: one hour for two Mechanical Technicians.
Analysis of the results (paragraph 3.B.4.):
Estimated Man-hours: one hour for one Mechanical Technician.
The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.
The estimate of the helicopter downtime is four hours (except time for metallurgical analysis).
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
Revision 0 2023-01-25  Page 4/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
1.K. REFERENCES
Aircraft Maintenance Manual (AMM):
AMM: 05-50-00,6-1: Procedure in the Event of Detection of Chips and / or Illumination of "MGB P" and / or
"MGB TEMP" Warning Lights - TGB / MGB - Unscheduled Inspections
AMM: 60-00-00,6-2A: Check - Chips detector - General - Mechanical Systems
Standard Practices Manual (MTC):
MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power generating
systems - Technical instructions
MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions
MTC: 20-08-01-601: Monitoring of lubricating oil contamination on mechanical assemblies equipped with
magnetic plugs - Periodical monitoring of lubricating oil checking elements
Information Notices (IN):
IN: 3481-1-00: The Marketplace: an AirbusWorld Ordering service
IN: 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight
1.L. OTHER AFFECTED PUBLICATIONS
Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
Revision 0  2023-01-25  Page 5/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For information about the price of the modification kits and/or components, or for aid, contact the
Airbus Helicopters Network Sales and Customer Relations Department.
Availability
Contact the Sales and Customer Relations Department to know the delivery lead time the operator's request.
Procurement
Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations
Department:
Airbus Helicopters
Etablissement de Marignane
Direction des Ventes et Relation Client
13725 MARIGNANE CEDEX
FRANCE
In the purchase order, write the information that follows:
- The mode of transport
- The destination
- The serial numbers of the helicopters to change.
2.B. LOGISTIC INFORMATION
Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Consumables to be ordered separately:
Refer to the Tasks given in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  P/N  Item
Cleaning agent  1 L  Commercial P/N  CM 296  1
Oil  0.3 L  ECS2199.10  CM 125  2
You can order the consumables from the AirbusWorld Marketplace through e-ordering (IN No. 3481-1-00).
If you cannot get access to e-ordering, please contact your Logistic Focal Point.
Revision 0 2023-01-25  Page 6/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
Special tools:
Refer to the Tasks given in this ALERT SERVICE BULLETIN and the list that follows:
Key Word  Qty  Tool P/N or equivalent  Item
1  Olympus Iplex rx/rt type iv9420RX
Boroscope
or equivalent
Magnet  Commercial P/N
8L pneumatic oil extractor vacuum  1  GEPCO 8L Air Powered Oil
pump  Removing & Filling Tool for Cars
transmissions ref. AT0754 or
equivalent
Tank  Vacuum pump sub-assembly  xx1
Top  Vacuum pump sub-assembly  xx2
Flexible hose  Vacuum pump sub-assembly  xx3
Semi rigid hose  Vacuum pump sub-assembly  xx4
Pistol grip  Vacuum pump sub-assembly  xx5
Connection  Vacuum pump sub-assembly  xx6
Safety valve  Vacuum pump sub-assembly  xx7
Connection  Vacuum pump sub-assembly  xx8
Connection  Vacuum pump sub-assembly  xx9
Connection  Vacuum pump sub-assembly  xx10
Syringe  1  Commercial P/N  ww
Container of light color  1  Commercial P/N  VV
Transparent adhesive tape and  1  KA0225-3  uu
transparent support sheet
NOTE
If another vacuum pump is used as an alternative to vacuum
pump (xx), adapt the procedure of the paragraph 3.B.3. of this
ALERT SERVICE BULLETIN in accordance with the other
pump.
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2023-01-25  Page 7/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
Not applicable.
3.B. WORK STEPS
CAUTION
MAKE SURE THAT YOU PREVENT ALL POSSIBLE
FOREIGN OBJECT DEBRIS (FOD).
3.B.1. Preliminary steps
- Disconnect all the electrical power supplies refer to the Work Card 20-07-03-406 (MTC).
- Install the access equipment.
- Remove and/or open all cowlings, panels, doors and all equipment items to enable adequate access to the
various work areas.
3.B.2. Visual inspection of the bevel wheel (Figure 1 and Figure 2)
CAUTION
COMPLY  WITH  THIS PARAGRAPH AT ROOM
TEMPERATURE.
- Open the filler plug (a1) of the MGB (a).
- Remove the strainer (a2).
- Position the boroscope (zz) above the bevel wheel (a3) without contact with oil.
a2 —
а3
ZZ  аб
a4
Figure 2  a5
Figure 1
Revision 0  2023-01-25  Page 8/22
Ce document est disponible sur internet : www.airbush  licopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
CAUTION
TURN THE TAIL ROTOR SLOWLY TO DO THE
VISUAL INSPECTION WITH THE BOROSCOPE (zz).
- If the MGB is installed on the helicopter:
• Turn the main rotor (c) (not shown) clockwise slowly 2 times minimum with the tail rotor (b) (not shown).
- If the MGB is not installed on the helicopter or when you install a MGB on helicopter:
. Turn the MGB engine input flange (d) (not shown) clockwise slowly 12 times minimum with the hand.
NOTE 1
Do the visual inspection with 2 mechanical technicians (or 1
mechanical technician and 1 crew member), one to inspect
with the boroscope (zz) and one to turn the tail rotor (b) or
MGB engine input flange (d).
NOTE 2
If the bottom of the radius (a6) of the bevel wheel (a3) and/or
head screws (a4) (see Figure 2) are not clearly visible, contact
Airbus Helicopters for further instructions to the address that
follow:
https://airbusworld.helicopters.airbus.com
- Make sure that there is no particle on the bevel wheel (a3) (Figure 3 and Figure 4).
a3
Example of the presence of particles
Figure 3
Revision 0 2023-01-25  Page 9/22
Ce document est disponible sur internet : www.airb  licopters.com/techpub/

### Page 10 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
a3
Example of the presence
of particles
Figure 4
CAUTION
MAKE SURE YOU DO NOT LEAVE ANYTHING
INSIDE THE MGB (a).
NOTE 3
Examine precisely the specific area of the radius (a6) under
the teeth (a5) of the bevel wheel (a3) (Figure 2).
- If there is no particle on the bevel wheel (a3):
. Remove the boroscope (zz).
. Install the strainer (a2).
. Close the filler plug (a1) of the MGB (a).
. Comply with paragraph 3.B.5.
- If there are particles on the bevel wheel (a3):
. Comply to paragraph 3.B.3.
Revision 0 2023-01-25  Page 10/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
3.B.3. Collect of the particles on the bevel wheel
CAUTION
COMPLY  WITH  THIS PARAGRAPH AT ROOM
TEMPERATURE.
- Cut the semi rigid hose (xx4) of the vacuum pump (xx) to a length of 400 mm (15.74 in) (Figures 5 and 6).
xx4
xX
Figure 5
• Xx4
Figure 6
- Make a 45 degree angle with the semi rigid hose (xx4) of the vacuum pump (xx) (Figure 7).
xx4
Figure 7
Revision 0  2023-01-25  Page 11/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
xx3
xx4  xx10  xx5  xx9
Figure 8
- To limit the risk of particles blocked in the pistol grip (xx5), disconnect (Figure 8):
. The pistol grip (xx5).
. The connection (xx10).
. The connection (xx9).
- Connect directly the rigid hose (xx4) in the flexible hose (xx3) (Figure 9).
xx4  xx3
Figure 9
Revision 0  2023-01-25  Page 12/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
- Position the boroscope (zz) above the bevel wheel (a3) without contact with oil (Figure 10).
ZZ
- xx4
a3
Figure 10
- Connect the vacuum pump (xx) to a source of compressed air (not shown).
- Put the vacuum pump (xx) in suction mode (Figure 11).
NOTE 4
If another vacuum pump is used as an alternative to vacuum
pump (xx), adapt the procedure of this paragraph.
Dispense
Dispense
Suction
Figure 11
Revision 0 2023-01-25  Page 13/22
Ce document est disponible sur internet : www.airbushe  elicopters.com/techpub/

### Page 14 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
- Position the semi rigid hose (xx4) of the vacuum pump (xx) on the bevel wheel (a3) (Figures 10 and 12)
_a3
￾a4
• а6
Figure 12
- Refer to Figures 2 and 13:
- If the MGB is installed on the helicopter:
. Turn the main rotor (c) (not shown) clockwise slowly 2 times minimum with the tail rotor (b) (not shown).
- If the MGB is not installed on the helicopter or when you install a MGB on helicopter:
. Turn the MGB engine input flange (d) (not shown) clockwise slowly 12 times minimum with the hand.
- Use suction while oil is present or particles visible:
. Around the heads of the screws (a4).
. In the radius (a6) under the teeth (a5) of the bevel wheel (a3).
- аЗ
a4
xx4
а6
Figure 13
NOTE 5
Examine precisely the specific area of the radius (a6) under
the teeth (a5) of the bevel wheel (a3) (Figure 13).
CAUTION
MAKE SURE YOU DO NOT LEAVE ANYTHING
INSIDE THE MGB (a).
Revision 0 2023-01-25  Page 14/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
- Remove the semi rigid hose (xx4) from the MGB (a).
- Install the strainer (a2).
- Close the filler plug (a1) of the MGB (a).
- To drain particles stuck:
. Do the suction of 0.3 L minimum of new oil (2) with the vacuum pump (xx)
- Disconnect the vacuum pump (xx) from the source of compressed air (not shown).
- Make sure that there is no remaining pressure with the safety valve (xx7) of the vacuum pump (xx) (Figure
14).
￾xx7
Figure 14
-xx2
*xx6
xx3
Figure 15
Revision 0  2023-01-25  Page 15/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
- Disconnect (Figures 15 and 16):
. The flexible hose (xx3) from the connection (xx6) of the vacuum pump (xx)
xx3
xx8
- xx6
Figure 16
• The flexible hose (xx3) from the rigid hose (xx4).
. And the connection (xx8) from the flexible hose (xx3).
CAUTION
A LARGE QUANTITY OF PARTICLES CAN STAY IN THE
DIFFERENT PARTS OF THE TOOL (xx), DRAIN THE
DIFFERENT PARTS OF THE TOOL (xx) CAREFULLY.
- Opposite to the suction direction of the vacuum pump (xx), flush with the syringe (ww) and
cleaning agent (1) to collect particles which possibly stay inside:
• The flexible hose (xx3).
. And the semi rigid hose (xx4).
- Collect the oil and cleaning agent (1) from the semi rigid hose (xx4) and the flexible hose (xx3) in a clean
container of light color (vv) and appropriate capacity (Figure 20).
- Tap lightly the connection (xx10) above the container of light color (vv) to collect particles which possibly
stayed inside.
Revision 0  2023-01-25  Page 16/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
- Refer to Figure 15 and disconnect the top (xx2) of the vacuum pump (xx) from its tank (xx1).
- Connect the semi rigid hose (xx4) on the connection (xx6) of top (xx2) of the vacuum pump (xx) (Figure 17).
xx2  - ××6
Figure 17
- Flush with the syringe (ww) and cleaning agent (1) to collect particles which possibly remained inside the
connection (xx6) in the container (vv).
- Collect all the particles with the magnet (yy) (Figure 18, Figure 19 and Figure 20) in:
• The tank (xx1) of the vacuum pump (xx)
• The container (vv).
- Make sure that all the particles are collected in the tank (xx1) of the vacuum pump (xx) and in the
container (vV).
- Collect the particles with the transparent adhesive tape and transparent support sheet (uu) (not shown), refer
to paragraph 3.B.4.
XX1
Figure 19
Figure 18
Figure 20
Revision 0  2023-01-25  Page 17/22
Ce document est disponible sur internet : www.ail  licopters.com/techpub/

### Page 18 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
3.B.4. Analysis of the results
If not already done, perform the MGB inspection for particles. Refer
to Task 05-50-00,6-1 (AMM) paragraph F.1.b.(1)
For particles with length L < 0.1 mm and width 1 < 0.1 mm (other than
abrasion):
- Do not take them into account for the next phases of this flowchart.
- Record their collection in the particle tracking sheet. Refer to
Work Card 20-08-01-601 (MTC).
Characterize the type* of the collected particle(s).
Refer to Work Card 20-08-01-601 (MTC).
As an alternative, if particles cannot be characterized
in accordance with Work Card 20-08-01-601 (MTC):
Perform a metallurgical analysis of the collected
particles with type characterization.
Contact Airbus Helicopters and provide the following
elements:
Dimension and quantity
Metallurgical analysis
Particle tracking sheet. Refer to
Work Card 20-08-01-601 (MTC).
MGB log card
Pending the result, consider the particles as scales.
Miscellaneous  Manufacturing residuals  Abrasion
non metallic  (swarf, pin, lockwire)
waste materiel.
Resume flights under
normal maintenance.  Scale, flake,
splinter
Comply with criteria of
Work Card 20-08-01-601 (MTC).
Comply with criteria of
Work Card 20-08-01-601 (MTC).
Revision 0 2023-01-25  Page 18/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 19 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
Stot: for the total area collected
Smax: for the largest particle
L: for the longest particle
e: for the thickest particle
For all the scales, flakes, splinters collected since MGB
Time Since Overhaul (TSO) or Time Since New (TSN),
measure:
- Stot*.
- Smax*
- L*.
- e*
Stot* <10 mm=  10 mm ≤ Stot* < 50 mm2  Stot* ≥ 50 mm.
And  Or  Or
Smax* ≤ 1 mm  1 mm < Smax* < 2 mm=  Smax* ≥ 2 mm2
And  Or  Or
L* ≤ 1.5 mm  1.5 mm < L* < 2 mm  L* ≥ 2 mm
And  Or  Or
e* ≤ 0.2 mm.  0.2mm < e* < 0.4 mm  e* ≥ 0.4 mm
Resume flights under  Resume flights under
close monitoring. Refer  close monitoring. Refer
to paragraph 3.D.  to paragraph 3.D.
Perform a metallurgical analysis  - Perform a metallurgical  Comply with
of all particles collected not yet  analysis of all particles  Work card 20-08-01-601 (MTC)
analysed **  collected not yet  instructions applicable when
analysed within 50 FH  those criteria are exceeded
max.
- If not completed within
To avoid a potential  50 FH:
limitation to 50 FH in the  . Stop the flights.
event of subsequent
detection of particles
during close monitoring
period, carry out the
metallurgical analysis as  B
soon as possible
Revision 0 2023-01-25  Page 19/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

### Page 20 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
Stot: for the total area collected
Smax: for the largest particle
L: for the longest particle
e: for the thickest particle
There is scale,
flake, splinter
YES  made of planet  NO
gear outer race
material (see
appendix 4.A.)?
Comply with criteria of
Work Card 20-08-01-601 (MTC)
Scale, flake, splinter made of  Scale, flake, splinter  NOTE
planet gear outer race material  made of planet gear
with:  outer race material with:  • In case of particles found on the
bevel gear:
Stot* < 10 mm?  Stot* ≥ 10 mm*  . Do a check (QT out of criteria)
And  Or  of the mast bearing, the
Smax* ≤ 1 mm?  Smax* > 1 mm  epicyclic module and the bevel
And  Or  reduction module.
L* ≤ 1.5 mm  L* > 1.5 mm  - If the damaged module cannot be
And  Or  identified, contact Airbus
e* ≤ 0.2 mm.  e* > 0.2 mm.  Helicopters with metallurgical
analysis and make a Technical
Event (TE) to the address that
follow:
https://airbusworld.helicopters.air
Continue flights  bus.com
under close
monitoring.
Refer to
paragraph 3.D.  - If necessary, a ferry flight to return to base is
permitted
- Do a check (QT out of criteria) as per
Task 05-50-00,6-1 (AMM) (maintenance after
particles detection).
- Replace damaged module(s) by a
serviceable one (s).
'See NOTE
Revision 0 2023-01-25  Page 20/22
Ce document est disponible sur internet :  www.airbushelicopters.com/techpub/

### Page 21 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
3.B.5. Final steps
- Do an aspect check on the helicopter after inspection or repair, refer to the
Work Card 20-07-03-408 (MTC).
- Install again or close all cowlings, panels, doors and equipment removed and/or opened during preliminary
steps (paragraph 3.B.1. of this ALERT SERVICE BULLETIN).
- Connect all the electrical power supplies, refer to the Work Card 20-07-03-406 (MTC).
- Check the oil level of the MGB before the first flight.
- Remove the access equipment.
3.B.6. Ground run-up / flight test
Check the oil level of the MGB after the first flight.
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record the full compliance with this ALERT SERVICE BULLETIN, with the revision number, in the
Log Card (FM) of the MGB.
- Record compliance with this ALERT SERVICE BULLETIN (see IN 3785-1-00 for instructions):
QR code or hypertext link
NOTE 6
The  recording  of  compliance  with
ALERT SERVICE BULLETINS in the SB insight tool does not
replace the recording in the helicopter documents.
ASB EC130 05A040
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
Close monitoring:
- During close monitoring subsequent to the detection of particles when you comply with this
ALERT SERVICE BULLETIN:
. Check the magnetic plugs of the MGB every 50 FH, refer to Task 60-00-00,6-2A (AMM).
. Comply with paragraph 3.B.2. from 100 FH to 165 FH of the last particles detection.
• If, after accomplishment of 3.B.2., no particles are detected, stop the close monitoring cycle. Refer to
paragraph 1.E.2. of this ALERT SERVICE BULLETIN.
Revision 0 2023-01-25  Page 21/22
Ce document est disponible sur internet : www.airbush  licopters.com/techpub/

### Page 22 (OCR)

AIRBUS  HELICOPTERS
No. EC130-05A040
4. APPENDIX
4.A. Material characteristics of the MGB planet gears bearing
Table No. 2
Type  (SNR A)  (SNR B)
MP/N of the MGB
350A32-1082-03  350A32-1114-00
planet gears bearing
Outer Race material  15CrNi6 or 15CN6  32CDV13
NOTE
Refer to Work Card 20-08-01-601 (MTC) for the chemical
composition and the equivalent name of the material.
Revision 0  2023-01-25  Page 22/22
Ce document est disponible sur internet : www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
