# Airbus Helicopters Alert Service Bulletin EC130-52A019

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 01 ("Airbus ASB EC130-52A019 Rev 1"), 48 pages: PDF https://openairdocs.org/files/sha256/b6/92/b692bc866333c73fc02473406308ad7f9a7957cdc55e1ed34cbfb43db6579c97; text https://openairdocs.org/service-documents/airbus-helicopters/ec130-52a019/file/b692bc866333.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2016-3343, the docket of AD 2020-25-11. Not covered by OpenAirDocs’ CC0 dedication.
- Revision 01 ("Airbus Helicopters ASB No. EC130-52A019 Rev 1"), 48 pages: PDF https://openairdocs.org/files/sha256/07/f0/07f0470f216f3083dd6261f9376ed6f48553b35808670219b4d19c4419f610eb; text https://openairdocs.org/service-documents/airbus-helicopters/ec130-52a019/file/07f0470f216f.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2026-7226, the docket of a proposed AD (Federal Register 2026-14886). Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC130-52A019
- Latest revision known: EC130-52A019, Revision 01 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec130-52a019

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec130-52a019/proposed.md).

## Text (48 pages)

Revision 01, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2016-3343, the docket of AD 2020-25-11. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
Civil version: B4
ALERT SERVICE BULLETIN
SUBJECT: DOORS
Reinforcement of the door locking/unlocking mechanism
Corresponds to MOD 074619
For the attention of
Revision No.  Date of issue
Revision 0  2016-04-18
Revision 1  2016-07-12
Summary:
The purpose of this ALERT SERVICE BULLETIN is to reinforce the door locking/unlocking mechanism.
Reason for last revision:
The purpose of this ALERT SERVICE BULLETIN revision 1 is to:
- extend its effectivity,
- clarify the replacement process of the rod ends and the installation process of the reinforcements,
- reformat this document.
Compliance:
Airbus Helicopters makes compliance with this ALERT SERVICE BULLETIN mandatory.
Revision 0 2016-04-18  Page 1/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters equipped with composite doors, all P/NS except those beginning with 704A (metal doors),
PRE MOD 074619. The helicopter S/N: 4495 is not affected by compliance with this ALERT SERVICE
BULLETIN.
NOTE 1
Refer to the aircraft individual inspection record (or RIC
AMS) to identify the actual modification status of the aircraft.
1.A.2. Non-installed equipment or parts
- Sliding door P/N 350A25-0431-00xx.
- Sliding door mechanism P/N 677-5-20-000 (7050A4521009).
- RH swing door (RH crew door) P/N 350A25-0024-00.
- LH swing door (LH crew door) P/N 350A25-0426-00xx.
- LH swing door mechanism P/N 677-5-40-000 (704A41610078).
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
The purpose of this ALERT SERVICE BULLETIN revision 0 was to reinforce the door locking/unlocking
mechanism.
Several incidents on the LH doors (swing and sliding) revealed some weaknesses in the locking/unlocking
mechanism.
These mechanisms are subject to loads every time the doors are opened and closed. Such loads may cause
the mechanism rupture and locking.
In case of failure, the doors may remain locked, thus preventing their opening or jettisoning.
Consequently, Airous helicopters developed modification o14619 in order to improve the rellability of the
door locking/unlocking mechanism by:
- Reinforcing the rotation pin of the swing door linkage star (addition of a doubler),
- Replacing the rod ends which, when broken, prevent door opening and jettisoning, with rod ends made of
more resistant material.
The purpose of this ALERT SERVICE BULLETIN revision 1 is to:
- extend its effectivity,
- clarify the replacement process of the rod ends and the installation process of the reinforcements,
- reformat this document.
The compliance of this ALERT SERVICE BULLETIN revision 1 does not supersede the compliance with
revision O.
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Revision 0 2016-04-18  Page 2/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbusl  elicopters.com\techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
- Installing a reinforcing bracket riveted to the LH and RH swing door posts.
- Replacing the rod ends which, when broken, prevent opening of the sliding door and LH swing door.
NOTE 2
Compliance with this ASB requires removing the reinforcing
bracket of the sliding door POST ASB 52A009.
NOTE 3
Airbus Helicopters issued SB 52-018 (embodiment of the
modification 074635: reinforcement of the crew door control
Joint compliance of SB 52-018 with this ASB prevents
removal of the reinforcing brackets (1) and (2) installed in
this ASB and thus simplifies the operational procedure.
1.E. COMPLIANCE
The compliance of this ALERT SERVICE BULLETIN revision 1 does not supersede the compliance with
revision O.
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
The works must be done by the Operator on the helicopter and on non-installed equipment or parts.
Helicopters/installed equipment or parts:
Comply with paragraphs 3.B. of this ALERT SERVICE BULLETIN within 24 months following receipt of this
ALERT SERVICE BULLETIN issued on the date indicated at the foot of the page.
Non-installed equipment or parts:
Modify stocks as required and as per paragraph 3.B.5.
Building up spares stocks for compliance with this ALERT SERVICE BULLETIN is at the Operator's initiative.
Revision 0 2016-04-18  Page 3/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
1.F. APPROVAL
Approval of modifications:
The information or instructions relate to modification 074619 which was approved on April 20, 2015 by the
EASA for helicopters of civil versions subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN revision O was approved on
April 15, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil
versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN revision 1 was approved on
June 14, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil
versions subject to an Airworthiness Certificate.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following
personnel qualifications:
Qualification:  1 Composite Material Specialist
1 Mechanical Technician
1 Airframe Technician
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations: 20 hours approximately.
The estimated helicopter grounding time is three days approximately, excluding curing time of glass fabric
ply/plies under vacuum bag and drying time of the different products.
1.H. WEIGHT AND BALANCE
The impact of this ALERT SERVICE BULLETIN is negligible.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
Revision 0 2016-04-18  Page 4/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 5 (OCR)

* AIRBUS
HELICOPTERS  ASB No. EC130-52A019
1 K. REFERENCES
The following documents are necessary for compliance with this ALERT SERVICE BULLETIN:
Standard Practices Manual (MTC):
MTC: 20.02.04.401: Installation of rivets - Pitch and edge distance
MTC: 20.02.04.402: Installation of rivets - Retrofitting and repair
MTC: 20.02.04.601: General riveting acceptance requirements
MTC: 20.02.05.401: Joining by riveting
MTC: 20.02.06.101: Safetying assemblies: General
MTC: 20.02.06.401: Safetying plain pins
MTC: 20.02.06.404: Safetying with cotter pins
MTC: 20.02.09.101: Crack detection through dye penetrant inspection: General
MTC: 20.02.09.601: Checking structural parts/components using the dye penetrant procedure
MTC: 20.03.02.409: Installation of blind rivets ASN-NSA 1919 and 1921
MTC: 20.03.06.406: Structural repairs - Vacuum bag techniques
MTC: 20.04.01.402: Cleaning of removed individual parts with liquid solvents
MTC: 20.04.04.401: Surface treatment before painting
MTC: 20.04.04.409: Touch-up of local protective treatment on stainless steels
MTC: 20.04.05.101: General information about painting means and paint touch-ups
MTC: 20.04.05.420: Use of surfacer CA 8620
MTC: 20.06.01.101: General rules for bonding with adhesives
MTC: 20.06.01.102: Bonding method
MTC: 20.06.01.411: Application of HYSOL EA 9396 cement
MTC: 20.06.01.418: Bonding with adhesive - Use of EA 9395 adhesive
MTC: 20.06.04.306: Application of loads for Polyester or Epoxy resins
MTC: 20.07.03.408: Appearance checks on an aircraft after an inspection or repair
MTC: 20.08.05.103: Monitoring of parts in operation - marking - service life customization
Aircraft Maintenance Manual (AMM):
AMM: 25-27-00, 4-2: Removal/Installation - Door upholstery
AMM: 52-11-00, 4-1: Removal/Installation - Crew doors
AMM: 52-11-00, 5-2: Adjustment/Test - Crew door
AMM: 52-11-00, 6-2: Checking the penetration of the spring-loaded latch on crew and sliding doors
AMM: 52-11-00, 6-4: Checking the position and penetration of the locking finger in the cockpit door upper
AMM: 52-12-00, 4-1: Removal - Sliding door
AMM: 52-12-00, 4-2: Installation - Sliding door
AMM: 52-12-00, 5-1: Adjustment/Test - Sliding door
AMM: 52-12-00, 6-2: Checking the position and penetration of the locking finger in the sliding door lateral
AMM: 60-00-00, 3-1: General safety instructions - Mechanical assemblies
1.L. OTHER AFFECTED PUBLICATIONS
The modification shall be incorporated in the Illustrated Parts Catalog (IPC) and Aircraft Maintenance
Manual (AMM).
The updated IPC must be ordered by Customer.
The AMM shall be updated during a future revision.
Revision 0 2016-04-18  Page 5/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
Under this ALERT SERVICE BULLETIN, rod ends PRE and POST MOD are not interchangeable.
Mixability:
Mixability of parts PRE and POST MOD is prohibited.
Revision 0 2016-04-18  Page 6/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Components related to compliance with this ALERT SERVICE BULLETIN will be delivered free of charge by
Airbus Helicopters for 24 months following issue of this ALERT SERVICE BULLETIN.
For any information concerning modification kits and/or components or for assistance, contact the Sales and
Customer Relations Department.
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
2.C.1. Kits to be ordered for one helicopter or one assembly:
Key Word  Qty  New  P/N  Item  No.  Former  P/N  Instruction
Reinforcement of
door locking system  350A07-4619-0072
Reinforcing bracket  1  350A25-2016-20  1
Reinforcing bracket  1  350A25-2017-2001  2
Rod end  2  350A25-2012-00  3  677-1-10-514  discard
Rod end  350A25-2013-00  4  677-1-20-513  discard
Rod end  350A25-2014-00  5  677-2-10-511  discard
Rod end  350A25-2015-00  6  677-2-20-511  discard
Cotter pin  10  23310CA010015  7
Rivet  4  NAS1919C04S03U  8  See § 2.C.2.b
Cotter pin  EN2367-18020  9
Nut  5  22435BC060L  10
Rivet  4  ASNA0077E403  11  1-part reinforcement
Rivet  4  ASNA0077E404  12  Variant item 11
Rivet  4  ASNA0077E406  13  2-part reinforcement
Revision 0 2016-04-18  Page 7/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicop  oters.com\techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
NOTE 3
Compliance with this ASB requires removing the reinforcing
bracket of the sliding door POST ASB 52A009.
According to the configuration of the helicopter, the
reinforcing bracket POST ASB 52A009 can be in:
- 2 parts (plate (al) and bracket (am)) (Figure 2),
- 1 part (reinforcing bracket (aq)).
NOTE 4
To reinstall reinforcing bracket (aq), use rivets (11) or (12)
according to the thickness of the assembly to attach.
2.C.2. Equipment or parts to be ordered separately
2.C.2.a. Components to be ordered in case of the installation of a new swing door star support following a check
by dye penetrant inspection (paragraph 3.B.2.b.3. or paragraph 3.B.2.c.3.):
Key Word  Qty  New  PIN  Item  No.  Former  PIN  Instruction
Star support, swing  1  677-1-10-511  21
door
Rivet  2  NAS1919C04S04U  22
Rivet  2  NAS1921C04S03U  23
Components to be ordered in case of the installation of the reinforcing brackets of swing doors in case of
overlength of the rivet (8) (paragraph 3.B.2.b.6. or paragraph 3.B.2.c.6.):
Key Word  Qty  New  P/N  Item  No.  Former  P/N  Instruction
Rivet  4 NAS1919C04S02U  24  Variant item 8
NOTE S
For the installation of the reinforcing brackets (1) and (2),
use the rivets (8) or (24) according to the thickness of the
assembly to attach.
Revision 0 2016-04-18  Page 8/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
2.C.3. Consumables to be ordered separately
As per Work Cards and Tasks mentioned in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  Product P/N  CM  Item No.
Glass fabric  AR  ECS0030-27  31
Adhesive  AR  ECS0010.10  32
Grease  AR  DCSEA395  101  33
Grease  AR  DCSEA354  115  34
Primer paint  AR  ECS2067.20  35
Adhesive  AR  ECS6054-1031  6041  36
The products can be ordered separately, from the INTERTURBINE AVIATION LOGISTICS company.
Website:  http://www.interturbine.com
Telephone:  +49.41.91.809.300
AOG:  +49.41.91.809.444
2.C.4. Equipment or parts required for non-installed components
2.C.4.a. Sliding door 350A25-0431-00xx, non-installed:
New  Item  Former
Key Word  Qty  P/N  No.  P/N  Instruction
Rod end  2  350A25-2012-00  3  677-1-10-514  discard
Rod end  1  350A25-2013-00  4  677-1-20-513  discard
Rod end  1  350A25-2015-00  6  677-2-20-511  discard
Cotter pin  4  23310CA010015  7
Cotter pin  1  EN2367-18020  9
Nut  4  22435BC060L  10
2.C.4.b. RH swing door 350A25-0024-00, non-installed:
Key Word  Qty  New  P/N  Item  No.  Former  P/N  Instruction
Reinforcing bracket  1  350A25-2017-2001  2
Rivet  NAS1919C04S03U
Rivet  NAS1919C04S02U  24  Variant item 8
Cotter pin  23310CA010015  7
Cotter pin  1  EN2367-18020  9
NOTE 6
For the installation of the reinforcing bracket (2), use the
rivets (8) or (24) according to the thickness of the assembly
to attach.
Revision 0 2016-04-18  Page 9/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
2.C.4.c. LH swing door 350A25-0426-00xx, non-installed:
Key Word  Qty  New  P/N  Item  No.  Former  P/N  Instruction
Reinforcing bracket  350A25-2016-20  1  677-2-10-511
Rod end  350A25-2014-00  5  discard
Cotter pin  23310CA010015  7
Rivet  2  NAS1919C04S03U  8
Rivet  2  NAS1919C04S02U  24  Variant item 8
Cotter pin  1  EN2367-18020  9
Nut  1  22435BC060L  10
NOTET
For the installation of the reinforcing bracket (1), use the
rivets (8) or (24) according to the thickness of the assembly
to attach.
2.C.4.d. Sliding door mechanism 677-5-20-000, non-installed:
New  Item  Former
Key Word  Qty  P/N  No.  P/N  Instruction
Rod end  2  350A25-2012-00  3  677-1-10-514  discard
Rod end  1  350A25-2013-00  4  677-1-20-513  discard
Rod end  1  350A25-2015-00  6  677-2-20-511  discard
Nut  4  22435BC060L  10
2.C.4.e. LH swing door mechanism 677-5-40-000, non-installed:
Key Word  Qty  New  P/N  Item  No.  Former  P/N  Instruction
Rod end  350A25-2014-00  5  677-2-10-511  discard
Nut  22435BC060L  10
2.C.5. Special tools
The tooling below is necessary for compliance with this ALERT SERVICE BULLETIN.
Key Word  Qty  Tooling P/N or equivalent  Item No.
Rule  Commercial  УУ
Masking adhesive tape  Commercial  ZZ
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2016-04-18  Page 10/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Read and comply with instructions for installation of rivets as per MTC Work Cards 20.02.04.401,
20.02.04.402, 20.02.04.601, 20.02.05.401 and 20.03.02.409.
- Read and comply with instructions for safetying as per MTC Work Cards 20.02.06.101, 20.02.06.401 and
20.02.06.404.
- Read and comply with instructions on structural repairs by vacuum bag techniques as per MTC Work Card
20.03.06.406.
- Read and comply with instructions concerning cleaning of removed parts as per MTC Work Card
20.04.01.402.
- Read and comply with general instructions on painting means and paint touch-ups as per MTC Work Card
20.04.05.101.
- Read and comply with instructions for bonding with adhesive as per MTC Work Cards 20.06.01.101 and
20.06.01.102.
- Read and comply with instructions for application of HYSOL EA 9396 cement as per MTC Work Card
20.06.01.411.
- Read and comply with instructions for application of loads for Polyester or Epoxy resins as per
MTC Work Card 20.06.04.306.
- Read and comply with general mechanical instructions as per AMM Task 60-00-00, 3-1.
3.B. WORK STEPS
3.B.1. Preliminary steps
- Check the integrity of door locking by making sure that each door can be closed and locked correctly. If this
is not the case, comply with the following cards according to the area concerned:
. 52-11-00, 6-2 (AMM) to check the penetration of the spring-loaded latch on the crew and sliding doors,
. 52-11-00, 6-4 (AMM) to check the position and the penetration of the locking pin in the crew door upper
catch,
. 52-12-00, 6-2 (AMM) to check the position and the penetration of the locking pin in the sliding door lateral
- Remove the crew doors as per AMM Task 52-11-00, 4-1.
- Remove the sliding door as per AMM Task 52-12-00, 4-1.
- Remove the door upholsteries as per AMM Task 25-27-00, 4-2.
Revision 0 2016-04-18  Page 11/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2. Procedure
3.B.2.a. Sliding door
3.B.2.a. 1. Removal of locking mechanism (Figure 1, Figure 2)
NOTE 1
The photos below show a sliding door locking mechanism
with a 1-part reinforcing bracket (aq).
aq  aq
9
Sliding door locking mechanism POST ASB 52A009
NOTE 2
The reinforcing bracket can also be in 2 parts (plate (al) and
bracket (am)) (Figure 2).
- Removal of 1-part reinforcing bracket (bracket (aq)) (Figure 2 DETAIL B and SECTION E-E):
. Remove cotter pin (aj) and washer (k).
• Retain washer (k) and discard cotter pin (aj).
CAUTION
DO NOT DAMAGE CARBON FABRIC PLIES (ap) WHEN
REMOVING BRACKET (aq).
• Remove and discard rivets (ar) attaching bracket (aq) to stringer (an).
• Remove and retain bracket (aq).
Revision 0 2016-04-18  Page 12/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Removal of 2-part reinforcing bracket (plate (al) and bracket (am)) (Figure 2 DETAIL B,
SECTIONS C-C and D-D):
• Remove cotter pin (aj) and washer (k).
• Retain washer (k) and discard cotter pin (aj).
CAUTION
DO NOT DAMAGE CARBON FABRIC PLIES (ap) WHEN
REMOVING PLATE (al) AND BRACKET (am) ASSEMBLY.
• Remove and discard rivets (ak) attaching plate (al) and bracket (am) assembly to stringer (an).
. Remove and retain plate (al) and bracket (am) assembly.
- Disconnect rods (Figure 1 DETAIL A):
Rods (g) and (h):
. Remove cotter pin (c), washer (as) and pin (at) which connect rods (g) and (h).
• Retain pin (at) and washer (as).
. Discard cotter pin (c).
• Disconnect rod (g) from rod (h).
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (g) to star (a).
• Retain pin (x) and washer (as).
• Discard cotter pin (c).
. Disconnect rod (g) from star (a).
Rod (i):
• Remove cotter pin (c), washer (as) and pin (x) which connect rod i) to star (a).
. Retain pin (x) and washer (as).
• Discard cotter pin (c).
. Disconnect rod (i) from star (a).
Rod (t):
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (f) to star (a).
Retain pin (x) and washer (as).
. Discard cotter pin (c).
. Disconnect rod (f) from star (a).
Revision 0 2016-04-18  Page 13/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.a.2. Replacement of rod ends (Figure 1)
NOTE 3
The values of lengths L1, L2, L3 and L4 will be necessary
upon adjustment of the rods further to replacement of the
rod ends (see Appendix).
(Figure 1 DETAIL A)
Rod (f):
- Rotate the star (a) on its axis to free some space for the measurement and the replacement of the rod
end.
- Measure and record the value of length L1 of rod (f) end as per Appendix 4.A. 1.
- Remove and discard rod end (b) and nut (aa) from rod (f).
- Position nut (10) and rod end (3) on rod (f).
- Adjust rod end (3) to length L1, and safety using nut (10).
Rod (i):
- Measure and record the value of length L2 of rod (i) end as per Appendix 4.A.1.
- Remove and discard rod end (b) and nut (aa) from rod I).
- Position nut (10) and rod end (3) on rod (i).
- Adjust rod end (3) to length L2, and safety using nut (10).
Rod (g):
- Measure and record the value of length L3 of rod (g) end as per Appendix 4.A.1.
- Remove and discard rod end (e) and nut (aa) from rod (g).
- Position nut (10) and rod end (6) on rod (g).
- Adjust rod end (6) to length L3, and safety using nut (10).
Rod (h):
- Measure and record the value of length L4 of rod (h) end as per Appendix 4.A.1.
- Remove and discard rod end (d) and nut (aa) from rod (h).
- Position nut (10) and rod end (4) on rod (h).
- Adjust rod end (4) to length L4, and safety using nut (10).
3.B.2.a.3. Installation of locking mechanism (Figure 1, Figure 2)
- Connect rods (Figure 1 DETAIL A).
Connect rod (f) to star (a) using pin (x), washer (as) and cotter pin (7).
Connect rod (i) to star (a) using pin (x), washer (as) and cotter pin (7).
Connect rod (g) to star (a) using pin (x), washer (as) and cotter pin (7).
. Connect rods (g) and (h) to each other using pin (at), washer (as) and cotter pin (7).
- Apply grease (34) on pin of star (a).
- Make sure that the door mechanism correctly operates prior to installing reinforcing bracket.
- Installation of reinforcing bracket (aq) (Figure 2 DETAIL B, SECTION E-E)
. Measure the thickness to be assembled to determine rivets (11) or (12) to be used.
. Install bracket (aq) on stringer (an) using rivets (11) or (12).
Revision 0 2016-04-18  Page 14/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Installation of reinforcing bracket (plate (al) and bracket (am)) (SECTIONS C-C and D-D)
. Install plate (al) and bracket (am) assembly on stringer (an) using rivets (13).
- Install washer (k) and cotter pin (9) on pin of star (a) (DETAIL B).
- Apply grease (33) to the sliding door linkage hinges (Figure 1).
- Identify the modified sliding door as per paragraph 3.C.
Revision 0 2016-04-18  Page 15/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.b.LH swing door
3.B.2.b.1. Removal of locking mechanism and rod end (Figure 3)
LH swing door mechanism PRE MOD
- Disconnect rods: (Figure 3 DETAIL B):
Rod (u):
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (u) to star (a).
• Retain pin (x) and washer (as).
. Discard cotter pin (c).
. Disconnect rod (u) from star (a).
Rods (v) and (t):
. Remove cotter pin (c), washer (as) and pin (at) which connect rods (v) and (t) to star (a).
Retain pin (at) and washer (as).
Discard cotter pin (c).
. Disconnect rods (v) and (t) from star (a).
Rod (s):
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (s) to star (a).
. Retain pin (x) and washer (as).
• Discard cotter pin (c).
. Disconnect rod (s) from star (a).
- Remove star: (Figure 3 DETAIL B)
. Remove cotter pin (r), washer (k) and star (a).
• Retain star (a) and washer (k).
• Discard cotter pin (r).
Revision 0 2016-04-18  Page 16/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Remove rod end: (Figure 3 DETAIL B)
. Measure and record the value of length L6 of rod (v) end as per Appendix 4.A.2.
NOTE 4
The value of length L6 will be necessary upon adjustment of
the rod further to replacement of the rod end (see Appendix).
• Remove and discard rod end (z) and nut (aa) from rod (v).
3.B.2.b.2. Checking the star support pin by dye penetrant inspection (Figure 4)
- On star support (y), clean zones X and Y (Figure 4 DETAIL C).
- Check for cracks on pin (y1) of support (y), at zones X and Y, by dye penetrant inspection as per
MTC Work Cards 20.02.09.101 and 20.02.09.601 (DETAIL C):
. If a crack is found, install a new star support as per paragraph 3.B.2.b.3.
. Otherwise, directly comply with paragraph 3.B.2.b.4.
00
Check of the star support pin by dye penetrant inspection
Revision 0 2016-04-18  Page 17/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.b.3. Installation of a new star support (Figure 3, Figure 4)
NOTE 5
Compliance with paragraph 3.B.2.b.3. is not necessary if the
star support (y) pin is not cracked.
- Disconnect spring (ae) from inner handle (af) and remove rod (ag) to free the space required to
remove star support (y).
af
ae  ag  af  ae  ag
Overall dimensions of rod/spring assembly  Disconnecting spring
- Remove and discard glass fabric plies (ab) (Figure 4 Working area E DETAIL D).
- Clean the mating surfaces between glass fabric plies (ab) and the LH swing door skin.
- Remove and discard rivets (ac) and (ad) (Figure 3 DETAIL B).
- Remove and discard support (y).
- Clean the mating surfaces between the door skin and support (21).
- Interlay adhesive (36) (not shown) between the LH swing door skin and support (21) as per MTC Work
Card 20.06.01.418.
- Install support (21) using 2 rivets (22) and 2 rivets (23) as per MTC Work Card 20.03.02.409
(DETAIL B).
- Mark out working area Z (Figure 4 Working area E and DETAIL D) using commercial masking tape
(zz) (not shown).
CAUTION
DURING SANDING, DO NOT DAMAGE THE FIRST
CARBON FIBER DOOR SKIN PLIES.
- Using abrasive paper (grit size 80 to 240), sand the finish paint and primer on working area Z, down to
the carbon fiber (DETAIL D).
- Cut out two square-shaped glass fabric plies (31) as per working area E.
NOTE 6
If the surface of a glass fabric ply (31) enables it, it is
possible to cover several rivet heads with only one glass
fabric ply (31).
Revision 0 2016-04-18  Page 18/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
NOTE 7
When installing a glass fabric ply (31) centered on several
rivet heads (23), it is necessary to leave a distance of at
least 20 mm between rivet head (23) and the square outer
edge.
- Apply adhesive (32) to glass fabric ply/plies (31) as per MTC Work Card 20.06.01.411.
- Center a glass fabric ply (31) on visible rivet heads (23).
- Cure glass fabric ply/plies (31) under a vacuum bag as per MTC Work Card 20.03.06.406.
- Carry out a surface treatment before painting as per MTC Work Card 20.04.04.401.
- Apply a coat of primer paint (35) to working area Z as per MTC Work Card 20.04.05.420.
- Apply a coat of finish paint according to the color of the LH swing door outer skin (DETAIL D).
- Apply grease (34) (DETAIL C) to zone X
- Install rod (ag) and spring (ae) of inner handle (af).
- Check flatness of installation zone of reinforcing bracket as per paragraph 3.B.2.b.4.
3.B.2.b.4. Checking flatness of installation zone of reinforcing bracket (Figure 5)
- Identify the installation zone of reinforcing bracket (1) in door post (w) (Figure 5 DETAIL B,
SECTION E-E).
- Clean the installation zone and check the mounting surface for flatness:
. If the flatness of the installation zone allows reinforcement (1) to be correctly installed, directly comply
with paragraph 3.B.2.b.6.
• Otherwise, install a glass fabric ply as per paragraph 3.B.2.b.5.
3.B.2.b.5. Installation of glass fabric ply (Figure 5)
NOTE &
Compliance with paragraph 3.B.2.b.5. is not necessary if the
flatness of the installation zone allows reinforcement (1) to
be correctly installed.
CAUTION
DURING SANDING, DO NOT DAMAGE THE FIRST
CARBON FIBER DOOR SKIN PLIES.
- Using abrasive paper (80 to 240 grit), sand the finish paint and primer on the installation zone of
reinforcing bracket (1) (Figure 5 SECTION E-E).
- Install a glass fabric ply (31), bonded using adhesive (22), on the installation zone of reinforcing
bracket (1).
NOTE 9
Glass fabric ply (31) shall protrude by 2 mm around
reinforcing bracket (1).
NOTE 10
The orientation of glass fabric ply (31) is of no importance.
Revision 0 2016-04-18  Page 19/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Cure fabric ply (31) under a vacuum bag.
- Apply a coat of finish paint according to the color of the LH swing door inner skin.
- Install reinforcing bracket and locking mechanism as per paragraph 3.B.2.b.6.
3.B.2.b.6. Installation of reinforcing bracket and locking mechanism (Figure 3, Figure 5)
NOTE 11
Airbus Helicopters issued SB 52-018 (embodiment of
modification 074635: reinforcement of the crew door control
Joint compliance with SB 52-018 and this ASB means that
reinforcing bracket (1) does not have to be removed and
thus simplifies the operational procedure.
- Install rod end : (Figure 5 DETAIL B)
Rod (V):
• Position nut (10) and rod end (5) on rod (v).
. Adjust rod end (5) to length L6, and safety using nut (10).
NOTE 12
Use the value of length L6 recorded in the table in Appendix
4.A.2.
- Using a rule (yy), measure and record dimension L7 between the center of pin (y) or (21) and door
post (w).
Dimension mea  ement method
Revision 0 2016-04-18  Page 20/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 21 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Transfer dimension L7 to reinforcing bracket (1).
2500126342 1326/331
Dimension transfer method
- Drill reinforcing bracket (1) to 6.2 mm diameter according to the center marking of pin (y) or (21)
(SECTION E-E).
- Position star (a) on pin (y) or (21) (DETAIL B).
- Position reinforcing bracket (1) while providing a clearance of at least 0.5 mm (.019 in.) between star
(a) and reinforcing bracket (1) while making sure that cotter pin (9) can freely be fitted (SECTION E-E).
a
Positioning reinforcing bracket
A CAUTION
WHILE DRILLING THE POST (W), HOLD THE ROD
(S) TO PREVENT ANY DAMAGE.
- Drill two holes to 3.3 mm diameter on door post (w) and ply (31) (if paragraph 3.B.2.b.5. complied with)
to match reinforcing bracket (1).
Revision 0 2016-04-18  Page 21/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 22 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Remove reinforcing bracket (1) and star (a).
or
21
Removal of star
- Deburr and clean reinforcing bracket (1) and door post (w).
- Carry out protection touch-ups on reinforcing bracket (1) as per MTC Work Card 20.04.04.409.
- On post (w) of LH swing door:
. Carry out a surface treatment before painting as per MTC Work Card 20.04.04.401.
. Apply a coat of primer paint (35) as per MTC Work Card 20.04.05.420.
- Position star (a) on pin (y) or (21) with grease (34) (DETAIL B).
- Position reinforcing bracket (1) without attaching it in the LH swing door post in order to facilitate
access for the rod (s) connection.
Positioning of reinforcing bracket
- Connect rods:
. Connect rod (s) to star (a) using pin (x), washer (as) and cotter pin (7).
. Connect rods (v) and (t) to star (a) using pin (at), washer (as) and cotter pin (7).
. Connect rod (u) to star (a) using pin (x), washer (as) and cotter pin (7).
Revision 0 2016-04-18  Page 22/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 23 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Temporarily fasten reinforcement (1).
Temporary fastening of reinforcing bracket
- Make sure that the door mechanism correctly operates prior to riveting reinforcing bracket (1).
- Attach reinforcing bracket (1) to door post (w) using rivets (8) or (24) (SECTION E-E).
- Safety pin (y) or (21) using washer (k) and cotter pin (9) (DETAIL B).
- Apply grease (33) to the LH swing door linkage hinges.
- Identity the modified LH swing door as per paragraph 3.C.
Revision 0 2016-04-18  Page 23/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 24 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.c. RH swing door
3.B.2.c.1. Removal of locking mechanism (Figure 6)
(S1/1A) 42504D
a
RH swing door mechanism PRE MOD
- Disconnect rods (Figure 6 DETAIL B):
Rod (q):
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (q) to star (a).
• Retain pin (x) and washer (as).
. Discard cotter pin (c).
. Disconnect rod (q) from star (a).
Rod (p):
. Remove cotter pin (c), washer (as) and pin (x) which connect rod (p) to star (a).
• Retain pin (x) and washer (as).
• Discard cotter pin (c).
. Disconnect rod (p) from star (a).
Rod (o):
• Remove cotter pin (c), washer (as) and pin (x) which connect rod (o) to star (a).
• Retain pin (x) and washer (as).
. Discard cotter pin (c).
. Disconnect rod (o) from star (a).
- Remove star (Figure 6 DETAIL B)
• Remove cotter pin (r), washer (k) and star (a).
• Retain star (a) and washer (k).
. Discard cotter pin (r).
Revision 0 2016-04-18  Page 24/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 25 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.c.2. Checking the star support pin by dye penetrant inspection (Figure 4, Figure 6)
- On star support (n), clean zones X and Y (Figure 4 DETAIL C).
- Check for cracks on pin (n1) of support (n), at zones X and Y, by dye penetrant inspection as per MTC
Work Cards 20.02.09.101 and 20.02.09.601:
• If a crack is found, install a new star support as per paragraph 3.B.2.c.3.
. Otherwise, directly comply with paragraph 3.B.2.c.4.
3.B.2.c.3. Installation of new star support (Figure 4, Figure 6)
NOTE 13
Compliance with paragraph 3.B.2.c.3. is not necessary if the
star support (n) pin is not cracked.
- Remove and discard glass fabric plies (ab) (Figure 4 Working area E, DETAIL D).
- Clean the mating surfaces between glass fabric plies (ab) and the RH swing door skin.
- Remove and discard rivets (ac) and (ad) (Figure 6 DETAIL F).
- Remove and discard support (n).
- Clean the mating surfaces between the RH swing door skin and support (21) to be reinstalled.
- Interlay adhesive (36) (not shown) between the RH swing door skin and support (21) as per MTC
Work Card 20.06.01.418.
- Install support (21) using two rivets (22) and two rivets (23) as per MTC Work Card 20.03.02.409
- Mark out working area Z (Figure 4 working area E) using commercial masking tape (zz) (not shown).
CAUTION
DURING SANDING, DO NOT DAMAGE THE FIRST
CARBON FIBER DOOR SKIN PLIES.
- Using abrasive paper (80 to 240 grit), sand the finish paint and primer on working area Z, down to the
carbon fiber.
- Cut out two square-shaped glass fabric plies (31) as per working area E.
NOTE 14
If the surface of a glass fabric ply (31) enables it, it is
possible to cover several rivet heads with only one glass
fabric ply (31).
NOTE 15
When installing a glass fabric ply (31) centered on several
rivet heads (23), it is necessary to leave a distance of at
least 20 mm between rivet head (23) and the square outer
edge.
- Apply adhesive (32) to glass fabric ply/plies (31) as per MTC Work Card 20.06.01.411.
- Center a glass fabric ply (31) on visible rivet heads (23).
- Cure glass fabric ply/plies (31) under a vacuum bag as per MTC Work Card 20.03.06.406.
- Carry out a surface treatment before painting as per MTC Work Card 20.04.04.401.
- Apply a coat of primer paint (35) to working area Z as per MTC Work Card 20.04.05.420.
Revision 0 2016-04-18  Page 25/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 26 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Apply a coat of finish paint according to the color of the RH swing door outer skin (DETAIL D).
- Apply grease (34) to zone X (DETAIL C).
- Check flatness of the installation zone of the reinforcing bracket as per paragraph 3.B.2.c.4.
3.B.2.c.4. Checking flatness of installation zone of reinforcing bracket (Figure 7)
- Identify the installation zones of reinforcing bracket (2) on door post (m) (Figure 7 DETAIL F,
SECTION G-G).
- Clean the installation zones and check the mounting surface for flatness:
• If the flatness of the installation zone allows reinforcing bracket (2) to be correctly installed, directly
comply with paragraph 3.B.2.c.6.
. Otherwise, install 2 glass fabric plies as per paragraph 3.B.2.c.5.
3.B.2.c.5. Installation of glass fabric plies (Figure 7)
NOTE 16
Compliance with paragraph 3.B.2.c.5. is not necessary if the
flatness of the installation zone allows reinforcing bracket (2)
to be correctly installed.
CAUTION
DURING SANDING, DO NOT DAMAGE THE FIRST
CARBON FIBER DOOR SKIN PLIES.
- Using abrasive paper (80 to 240 grit), sand the finish paint and primer on the installation zone of
reinforcing bracket (2).
- Install two glass fabric plies (31), bonded using adhesive (32), on the installation zones of reinforcing
bracket (2) (Figure 7 SECTION G-G).
NOTE 17
Glass fabric plies (31) shall protrude by 2 mm around
reinforcing bracket (2).
NOTE 18
The orientation of glass fabric plies (31) is of no importance.
- Cure fabric plies (31) under a vacuum bag.
- Apply a coat of finish paint according to the color of the RH swing door inner skin.
- Install reinforcing bracket and locking mechanism as per paragraph 3.B.2.c.6.
Revision 0 2016-04-18  Page 26/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 27 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.2.c.6. Installation of reinforcing bracket and connection of rods (Figure 7)
NOTE 19
Airbus Helicopters  issued SB 52-018 (embodiment of
modification 074635: reinforcement of the crew door control
rods).
Joint compliance with SB 52-018 and this ASB means that
reinforcing bracket (2) does not have to be removed and
thus simplifies the operational procedure.
- Using a rule (yy), measure and record dimension L5 between the center of pin (n) or (21) and door
post (m).
n or 21
a
RH swing door mechanism PRE MOD
- Transfer dimension L5 to reinforcing bracket (2).
- Drill reinforcing bracket (2) to 6.2 mm diameter according to the center marking of pin (n) or (21)
(Figure 7 SECTION G-G).
- Position star (a) on pin (n) or (21) (DETAIL F).
- Position reinforcing bracket (2) while providing a clearance of at least 0.5 mm (.019 in.) between star
(a) and reinforcing bracket (2) while making sure that cotter pin (9) can freely be fitted
(SECTION G-G).
< 00  80 051
Check of the clearance of at least 0,5mm (.019 in.)
Revision 0 2016-04-18  Page 27/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 28 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
• CAUTION
WHILE DRILLING THE POST (m), HOLD THE ROD
(o) TO PREVENT ANY DAMAGE.
- drill two holes to 3.3 mm diameter on door post (m) and plies (31) (if paragraph 3.B.2.c.5. complied
with) to match reinforcing bracket (2).
0F 50375665  21A2102101
2
Drilling door post
- Remove reinforcing bracket (2) and star (a).
- Deburr and clean reinforcing bracket (2) and door post (m).
- Carry out protection touch-ups on reinforcing bracket (2) as per MTC Work Card 20.04.04.409.
- On RH swing door post (m):
. Carry out a surface treatment before painting as per MTC Work Card 20.04.04.401.
. Apply a coat of primer paint (27) as per MTC Work Card 20.04.05.420.
- Position star (a) on pin (n) or (21) with grease (34) (DETAIL F).
- Temporarily fasten reinforcement (2).
2
Temporary fastening of reinforcement
- Connect rods:
Connect rod (o) to star (a) using pin (x), washer (as) and cotter pin (7).
. Connect rod (p) to star (a) using pin (x), washer (as) and cotter pin (7).
. Connect rod (q) to star (a) using pin (x), washer (as) and cotter pin (7).
- Make sure that the door mechanism correctly operates prior to riveting reinforcing bracket (2).
- Measure the thickness to be assembled to determine rivets (8) or (24) to be used for installation of
reinforcing bracket (2).
Revision 0 2016-04-18  Page 28/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 29 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
- Attach reinforcing bracket (2) to door post (m) using rivets (8) or (24) (SECTION G-G).
RH swing door mechanism POST MOD
- Safety pin (n) or (21) using washer (k) and cotter pin (9).
- Apply grease (33) to the RH swing door linkage hinges.
- Identify the modified RH swing door as per paragraph 3.C.
3.B.3. Tests
- Check the adjustment of the internal and external handles of the crew doors as per
AMM Task 52-11-00, 5-2.
- Check the adjustment of the internal and external handles of the sliding door as per
AMM Task 52-12-00, 5-1.
- Check the penetration of the spring-loaded latch on the crew and sliding doors as per
AMM Task 52-11-00, 6-2, using the penetration criteria recorded upon paragraph 3.B.1.
- Check the position and penetration of the locking finger in the cockpit door upper catch as per
AMM Task 52-11-00, 6-4, using the penetration criteria recorded upon paragraph 3.B.1.
- Check the position and penetration of the locking finger in the sliding door lateral catch as per
AMM Task 52-12-00, 6-2, using the penetration criteria recorded upon paragraph 3.B.1.
3.B.4. Final steps
- Install the door inside upholsteries as per AMM Task 25-27-00, 4-2.
- Install the crew doors as per AMM Task 52-11-00, 4-1.
- Install the sliding door as per AMM Task 52-12-00, 4-2.
- Carry out appearance checks of an aircraft after inspection or repair as per MTC Work Card 20.07.03.408.
3.B.5. Work steps for non-installed equipment or parts
3.B.5.a. Sliding door 350A25-0431-00xx, non-installed
- Comply with paragraph 3.B.2.a.
3.B.5.b. LH swing door 350A25-0426-00xx, non-installed
- Comply with paragraph 3.B.2.b.
3.B.5.c. RH swing door 350A25-0024-00, non-installed
- Comply with paragraph 3.B.2.c.
Revision 0 2016-04-18  Page 29/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 30 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.B.5.d. Sliding door mechanism 677-5-20-000, non-installed (Figure 1)
NOTE 20
DETAIL  represents an  assembled sliding  door
mechanism, the non-installed door mechanisms are packed
in non-assembled condition.
- In the sliding door mechanism kit: (DETAIL A)
. Discard nuts (aa) and rod ends (b), (d) and (e).
. Replace with nuts (10) and rod ends (3), (4) and (6).
- Identify the modified sliding door mechanism as per paragraph 3.C.
3.B.5.e. LH swing door mechanism 677-5-40-000, non-installed (Figure 3)
NOTE 21
DETAIL B represents an assembled LH swing door
mechanism, the non-installed door mechanisms are packed
in non-assembled condition.
- In the LH swing door mechanism kit: (DETAIL B)
. Discard nut (aa) and rod end (z).
• Replace with nut (10) and rod end (5).
- Identify the modified LH swing door mechanism as per paragraph 3.C.
Revision 0 2016-04-18  Page 30/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 31 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
3.C. COMPLIANCE CONFIRMATION
Compliance with this document:
Record compliance with this ALERT SERVICE BULLETIN with the revision number in the aircraft
documents.
Tracking of modifications in the documentation:
Not applicable.
Identification of modifications on equipment or parts:
Identify parts/assemblies as per the table below and/or as per MTC Work Card 20.08.05.103.
Key Word  Former P/N  New P/N  MOD  Type of marking
Sliding door  7050A4521009  350A25-2042-00  074619  Label
mechanism
LH swing door  704A41610078  704A41610078 +  074619  Label
mechanism  ASB 52A019
Sliding door  350A25-0431-00xx  350A25-0431-00xx +  074619  Indelible ink
ASB 52A019
LH swing door  350A25-0426-00xx  350A25-0426-00xx +  074619  Indelible ink
ASB 52A019
RH swing door  350A25-0024-00  350A25-0024-00 +  074619  Indelible ink
ASB 52A019
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2016-04-18  Page 31/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 32 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 32/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 33 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
A  CM 101
CM 115
aa
10
CM 101
3
CM 115  aa
aa  g  aa  10  CM 101
10  10
Figure 1 - PRE/POST MOD sliding door
Revision 0  2016-04-18  Page 33/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 34 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 34/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 35 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
POST ASB 52A009  POST ASB 52A009
(2-part reinforcement)  (1-part reinforcement)
am
EÇ
aq
al
DÇ
SECTION  SECTION
C-C  E-E
ar
11 ou/or 12
ak
13
SECTION
ak  D-D
13
ap
am
FWD
ar
11 ou/or 12
Figure 2 - Removal and re-installation of reinforcements POST ASB 52A009
Revision 0  2016-04-18  Page 35/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 36 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 36/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 37 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PRE MOD 074619
y or 21
ad
23
y or 21
ac
22
See Figure 4
at
as
aa
External handle axle
at
as
Figure 3 - PRE MOD LH swing door
Revision 0  2016-04-18  Page 37/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 38 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 38/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 39 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
LH side shown
D  RH symmetrical
C RH symmetrical  LH side shown
FWD
Working areas E
y1 RH  CM 115
n1 LH
Zone X - 34
Working area E
23
y RH
n LH  Zone Y
100 mm
(3.94 in.)  35
Working area Z
110 mm (4.33 in.)
Figure 4 - Inspection of star support by dye penetrant inspection
Revision 0 2016-04-18  Page 39/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbush  licopters.com\techpub

### Page 40 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 40/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 41 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
yor 21  POST MOD 074619  CM 115
34
y or 21
CM 101
SECTION
E-E
See Nota 9
32
KE
CM 101
as
FWD  8 or 24
See Nota 9  See Nota 9
Figure 5 - POST MOD LH swing door
Revision 0  2016-04-18  Page 41/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 42 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 42/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 43 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PRE MOD 074619
nor 21
n ou 21
as
See Figure 4
ac
22
as  External handle axle
as
Figure 6 - PRE MOD RH swing door
Revision 0  2016-04-18  Page 43/48
Revision 1  2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 44 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 44/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 45 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
POST MOD 074619
SECTION
CM 115  G-G
n or 21
CM 101  See Nota 17
CM 101
8 or 24
FWD
n or 21
See Nota 17
m
35
8 or 24
0.5 MINI
See Nota 17
CM 101
See Nota 17
Figure 7 - POST MOD RH swing door
Revision 0  2016-04-18  Page 45/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 46 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-04-18  Page 46/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 47 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
4. APPENDICES
4.A. ADJUSTMENT OF ROD ENDS
4.A.1 Measurement of sliding door rod end lengths
9
L2
Length  Measured value
L1
L2
L3
L4
Revision 0 2016-04-18  Page 47/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbushelicopters.com\techpub

### Page 48 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC130-52A019
4.A.2 Measurement of swing door rod end lengths
L6
Length  Measured value
L6
Revision 0 2016-04-18  Page 48/48
Revision 1 2016-07-12  This document is available on the Internet: www.airbusl  elicopters.com\techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
