# Eurocopter Alert Service Bulletin EC135-53A-017

Copy: Revision 1 ("U.S. DOT/FAA - Eurocopter ASB EC135-53A-017 Rev 1"), 10 pages: PDF https://openairdocs.org/files/sha256/cb/71/cb71ef5327661af5622d3241f3e97919fe64e7f57fdbfbc3b48cda25f179394f; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-53a017/file/cb71ef532766.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2008-0165; AD 2008-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135-53A-017
- Latest revision known: EC135-53A-017, Revision 1, dated June 22, 2007 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-53a017

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2008-04-05](https://openairdocs.org/ad/2008-04-05.md), effective Mar 6, 2008: Revision 1

## Text (10 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2008-0165; AD 2008-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
Fuselage - Cable Channel - Inspection of wire harnesses and
modification of side channel covers
1. Planning Information
A. Effectivity
(1) Helicopters affected:  EC135/EC635, all models S/N 0005 up to and including
S/N 0576.
(2) Components affected:  Wire harnesses in the LH and RH cable channel.
(3) Spare parts affected:  Not applicable.
B. Concurrent Requirements
Not applicable.
C. Reason
During a flight a burning odor could be smelt in the cabin. Its reason was a short circuit in
the LH cable channel, which was caused by a damaged wire harness. The wire harness was
damaged by the side channel cover's attachment hardware.
For this reason, a modified attachment of the side channel cover is introduced with this Alert
D. Description
Inspect wire harnesses in the LH and RH cable channel for chafing, remove screws and
anchor nuts from the area where the side channel covers overlap and replace by a
E. Compliance
Inspection of the wire harnesses and accomplishment of the chafing protection measures
must be accomplished within the next 25 fh after receipt of this Alert Service Bulletin, but by
28.02.2007 at the latest.
F. Approval
The technical content of this document is approved under the authority of
DOA No. EASA.21J.034.
2007-01-18  EC135-53A-017
REVISION 01, 2007-06-22  PAGE 1 of 10

### Page 2 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
G. Manpower
EFFECTIVITY Helicopters with collective lever cover (copilot).
Approx. 5 man-hours.
EFFECTIVITY Helicopters without collective lever cover (copilot).
Approx. 4 man-hours.
H. Weight and Balance
Not applicable.
Electrical Load Data
Not applicable.
J. Software Accomplishment Summary
Not applicable:
K. References
AMM EC135
AMM EC135/635 T1/T2 (CPDS).
L. Other Publications affected
The changes to AMM EC135, AMM EC135/635 T1/T2 (CPDS) and to IPC EC135, IPC
EC635 wich are required as a result of thie Alert Service Bulletin will be incorporated with
one of the next revisions.
M. Interchangeability of Parts
Not applicable.
2. Material Information
A. Material - Price and Availability
Information on cost and availability of required retrofit kit SB-135-53A-017-201 or
SB-135-53A-017-2C2 will be provided by ECD, Dept. Spares Order Administration on
request.
B. Support Information
Not applicable.
EC135-53A-017  2007-01-18
PAGE 2 of 10  REVISION 01, 2007-06-22

### Page 3 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
C. Material Necessary for Each Helicopter
EFFECTIVITY Helicopters without collective lever cover (copilot).
Retrofit kit SB-135-53A-017-2C1
No.  New P/N  Keyword  Old P/N  Qty  Disposition
1  Adhesive tape (double-sided)  a.n.*  B
(CM 6049)
2  Acetone (CM 203)  a.n.*
*a.n. = as needed
EFFECTIVITY Helicopters with collective lever cover (copilot).
Retrofit kit SB-135-53A-017-2C2
No.  New P/N  Keyword  Old P/N  Qty  Disposition
1  15147-05-20Farbe1002  Hook tape  1  A
Klettostar-Haftband  (0.6 m)
2  15244-05-20Farbe1002  Pile tape  1
Klettostar-Flauschband  (0.6 m)
Adhesive tape (double-sided)  a.n.*  B
(CM 6049)
4  Acetone (CM 203)  a.n.*  B
*a.n. = as needed
Disposition:
A = New, included in kit.
B = Consumable material, to be ordered from the Interturbine company as needed
CM item number i.a.w. list of consumable materials in the AMM.
D. Material Necessary for Each Spare
Not applicable.
E. Reidentified Parts
Not applicable.
F. Special Tooling
Not applicable.
2007-01-18  EC135-53A-017
REVISION 01, 2007-06-22  PAGE 3 of 10

### Page 4 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
3. Accomplishment Instructions
A. Preliminary work steps:
(1) De-energize helicopter electrical system i.a.w. AMM, 24-00-00, 2-1.
(2) If present, remove floor cover from the area of the LH and RH side channel covers i.a.w.
AMM, 25-10-00, 4-2.
(3) If present, remove cover from collective lever (copilot) i.a.w. AMM, 67-12-00, 4-8.
(4) Remove LH and RH side channel covers i.a.w. AMM, 52-50-00, 4-3.
B. Inspection of wire harnesses in the LH and RH cable channel:
(1) Inspect wire harnesses i.a.w. Figure 1 for chafing and damage and, while doing so,
especially inspect the area beneath the attachment screws of the side channel covers.
If wire harnesses are damaged, contact the ECD customer service before the next flight
for further instructions.
If additional items of optional equipment are installed on the side channel covers,
inspect beneath lying wire harnesses and contact the ECD customer service in case
of doubt.
(3)  If no signs of damage can be detected in the wire harnesses, proceed i.a.w. Section 3.C
of this Alert Service Bulletin.
C. Modification of the side channel covers:
NOTE  The following instructions are effective for the LH cable channel. The
instructions for the RH cable channel are identical.
(1) If present, remove foam rubber (5, Figure 2).
(2) Drill out countersunk rivets (1, Figure 2) using drill bit dia. 2.4 mm.
(3) Remove two anchor nuts (4, Figure 2) and sheet (3).
(4) Affix double-sided adhesive tape (6, Figure 2) onto side channel cover (2). By doing
so, remove protective backing film not until side channel cover (2) and side channel
cover (7) are installed
Clean areas to be affixed before affixing of the double-sided adhesive tape with
acetone (CM 203).
EC135-53A-017  2007-01-18
PAGE 4 of 10  REVISION 01, 2007-06-22

### Page 5 (OCR)

eurocopter  EC135
an EADS Compeny
ALERT SERVICE BULLETIN
EFFECTIVITY For helicopters with collective lever cover (copilot).
D. Modification of the attachment of the collective lever cover (copilot):
(1) Drill out rivets (6) from the side channel cover (4, Figure 3) using drill bit dia.
2.4 mm.
a)  Remove the two anchor nuts (5, Figure 3).
(D)  Attach hook-and-pile tape (8, 10, Figure 3) onto the cover (3):
1 Clean bonding surfaces of the side channel cover (4, Figure 3) with
acetone (CM 203).
2 Mark position of the pile tape (10, Figure 3) onto the side channel cover (4).
Peel off protective backing strip of the pile tape (10, Figure 3) and affix pile
tape (10) to the side channel cover (4).
4. Clean bonding surfaces of the cover (3, Figure 3) of the collective lever
(copilot) with acetone (CM 203).
5 Peel off protective backing strip of the hook tape (8, Figure 3) and affix hook
tape (8) to the cover (3).
EFFECTIVITY All.
Attach chafing protection (e.g. ROUNDIT2000NX, chafing protection must correspond to
Aviation Standard) over the wire harnesse in the RH and LH cable channel. Inspect
installation position of the wire harnesses and, if necessary, correct:
(1) Attach chafing protection (7, Figure 4) over the wire harnesses (2) which are next to the
anchor nuts (3) and attach by means of ty-raps (5).
If the clearance between anchor nuts (3, Figure 4), screws (4) and the wire
harnesses (2) is less than 4 mm, route wire harnesses until the specified minimum
clearance of 4mm is reached and then fix wire harnesses (2) by means of ty-raps (5).
F. Conclusive work:
CAUTION  PAY ATTENTION THAT THE SPECIFIED SCREWS ARE USED FOR
INSTALLATION OF THE SIDE CHANNEL COVERS, AS TOO LONG
SCREWS MAY DAMAGE THE BENEATH LYING WIRE HARNESSES.
(1) Install LH and RH side channel covers i.a.w. AMM, 52-50-00, 4-3. By doing so, pay
attention to the modified attachment of the side channel covers by a double-sided
adhesive tape i.a.w. Section 3.C.
If other screws than screws LN9136-05012 are used in the places of Figure 4 which are
marked with an "X", replace screws accordingly.
EFFECTIVITY For helicopters with collective lever cover (copilot).
(2) Install collective lever cover (copilot) i.a.w. AMM, 67-12-00, 4-8. By doing so, pay
attention to the modified attachment of the cover by hook-and-pile tapes i.a.w. Section
3.D and replace the two remaining screws with screws LN9139M4X16.
2007-01-18  EC135-53A-017
REVISION 01, 2007-06-22  PAGE 5 of 10

### Page 6 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
EFFECTIVITY All.
(3) If removed, install floor cover i.a.w. AMM, 25-10-00, 4-2.
G. Confirm accomplishment of this Alert Service Bulletin by an entry in the historical record of
the helicopter.
4. Appendix
Not applicable.
EC135-53A-017  2007-01-18
PAGE 6 of 10  _ REVISION 01, 2007-06-22

### Page 7 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
FLIGHT DIRECTION
/1 Inspect wire harnesses for chafing and damage. By doing so, especially
inspect the area where the side channel covers are screwed.
Inspection of Wire Harnesses
Figure 1
2007-01-18  EC135-53A-017
REVISION 01, 2007-06-22  PAGE 7 of 10

### Page 8 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
1×4
View A
3×2
4×2
1  Countersunk rivet
2 Side channel cover 1
3 Sheet
4 Anchot nut
5 Foam rubber
6 Double-sided adhesive tape (CM 6049)
7 Side channel cover 21
/1 Only LH side channel cover is shown.
Modification of Side Channel Cover
Figure 2
EC135-53A-017  2007-01-18
PAGE 8 of 10  REVISION 01, 2007-06-22

### Page 9 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
Before modification.
1x2
2x2
After modification.
7X2
6X4
9x2
Screw 41
2 Washer 1
3 Cover
4 Side channel cover
Anchor nut/1\
6 Rivet 4  10
7 Screw
8 Hook tape /2
9 Washer
10 Pile tape /2
1 Before modification.
/2 After modification.
3 Establish screw holes into the pile tape.
Modification of Collective Lever Cover (Copilot)
Figure 3
2007-01-18  EC135-53A-017
REVISION 01, 2007-06-22  PAGE 9 of 10

### Page 10 (OCR)

eurocopter  EC135
an EADS Company
ALERT SERVICE BULLETIN
2  Section A-A
Cable channel
2 Wire harness /1
3 Anchor nut
4  Screw 5
Ту-ґар /⅓
Side channel cover
7  Chafing protection
(e.g. ROUNDIT2000NX) /4
1) Typical routing of the wire harnesses in the cable channel.  7
2) The minimum clearance between wire harnesses and anchor nuts/screws must be 4 mm.
3 If necessary, route wire harnesses by additionally fixing them with ty-raps.
4 Attach a chafing protection over wire harnesses.
5) If other screws than screws LN9136-05012 are used in the places of Figure 4 which are
marked with an "X", replace screws accordingly.
Installation Position of Wire Harnesses
Figure 4
EC135-53A-017  2007-01-18
PAGE 10 of 10  REVISION 01, 2007-06-22

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
