# Eurocopter Alert Service Bulletin EC135-63A-013

Copy: Revision 02 ("ASB-EC135-EC635-63-013-Rev2-EN"), 8 pages: PDF https://openairdocs.org/files/sha256/32/a0/32a02df6d6d4e72542615ac969bc99e7bbd3237a477d2b3e31949b122c8f9088; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-63a013/file/32a02df6d6d4.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2009-0482; AD 2009-11-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135-63A-013
- Latest revision known: EC135-63A-013, Revision 02, dated September 12, 2008 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-63a013

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2009-11-10](https://openairdocs.org/ad/2009-11-10.md), effective Jun 12, 2009: Revision 02

## Text (8 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2009-0482; AD 2009-11-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT SERVICE BULLETIN
EC135
 
CHANGE INSTRUCTION NO. 2 FOR EC135-63A-013
PAGE 1 of 12008-09-12
 
Date: First  issue: 2008-09-10
Revision 01: 2008-09-12
Revision 02: 2008-09-12
Please replace Revision 01 of Alert Service Bulletin EC135-63A-013 with Revision 02.
With Revision 02 a printing error was corrected in Section 3.B.(7).
The dimension given in this section was corrected from 0.5 mm to 0.05 mm.

### Page 2

(No text on this page.)

### Page 3

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 1 of 6
2008-09-10
REVISION 02, 2008-09-12
Main Rotor Drive  –  Main Transmission  –  Check of screws at the lower
hub–shaft bearing for correct attachment
1. Planning Information
A. Effectivity
(1) Helicopters affected: EC135/EC635, all models with main transmission 
S/N 0001 to 1420 and 1500 to 1749.
(2) Components affected: P/N 4649 010 003, 4649 010 005, 
4649 010 006, 4649 010 006X, 4649 010 008, 
4649 010 008X, 4649 001 007 and 4649 010 010.
(3) Spare parts affected: see 1.A.(2)
B. Concurrent Requirements
Not applicable.
C. Reason
Unusual vibrations occurred during the start phase of the main rotor on one helicopter. These
vibrations stopped after the application of torque. The troubleshooting accomplished by the
maintenance personnel showed that six of the eight attachment screws of the lower
hub–shaft bearing support had loosened. After the affected operator’s fleet had been
inspected, two more main transmissions were found on which the screws of the lower
hub–shaft bearing support had loosened.
The lower hub–shaft bearing consists of a ball bearing and a roller bearing. The outer race
of the roller bearing is fixed to the housing with screws. If all attachment screws should
become loose, the outer race of the roller bearing might drop down. However, the axial
guidance of the rotor hub–shaft is still ensured.
D. Description
Remove interior panelling. Drain oil, secure attachment hardware by means of locking
washers.
E. Compliance
(1) If unusual vibrations are detected during the start or the end phase of the main rotor’s
running the attachment hardware must be secured with locking washers i.a.w. Section
3.B. of this Alert Service Bulletin no later than 3 flights after receipt of this Alert Service
Bulletin.
(2) The securing of attachment hardware i.a.w. Section 3.B of this Alert Service Bulletin
must be accomplished within the next 50 fh after receipt of this Alert Service Bulletin,
but by 31.03.2009 at the latest.
This document is available on the internet: www.eurocopter .com/techpub

### Page 4

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 2 of 6 REVISION 02, 2008-09-12
2008-09-10
(3) If the first issue of the Alert Service Bulletin has already been accomplished, the
attachment hardware must be secured i.a.w. Section 3.B of this Alert Service Bulletin
after 400 fh (plus a tolerance of 40 fh) at the latest.
(4) The main transmissions in stores are to be secured i.a.w. Section 3.B before their
installation at the latest.
F. Approval
The technical content of this document is approved under the authority of
DOA No. EASA.21J.034.
G. Manpower
– without EMS equipment: 4 h
– with EMS equipment: 8 h
H. Weight and Balance
Not applicable.
I. Electrical Load Data
Not applicable.
J. Software Accomplishment Summary
Not applicable.
K. References
– AMM EC135
– AMM EC135/635
L. Other publications affected
Not applicable.
M. Interchangeability of Parts
Not applicable.
2. Material Information
A. Material – Price and Availability
Not applicable.
B. Support Information
On receipt of the completed reply form sheet of page 6, retrofit kit EC135–63–011–2C3,
which contains 12 liters of lubricating oil (CM 1001) will be provided free of cost. Should the
main transmission still be filled with CM103 the retrofit kit EC135-63-011-2C2 (Retrofit
modification for the use of CM1001) is available on special terms. Further information will
be provided by ECD, Dept. Spares Order Administration on request.

### Page 5

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 3 of 6
2008-09-10
REVISION 02, 2008-09-12
C. Material Necessary for Each Helicopter
Material kit SB-135-63A-013-2C.
No. New P/N Keyword Old P/N Qty Disposition
1 0634313686 O−ring 0634313686 1 A
2 0639021002,
alternatively
0639021005
Locking washer LN9023B6
alternatively
Locking washer LN9023A6
both in material 1.4544.9
− 8 A
Disposition:
A = New, included in kit, the O–ring can be reused once.
D. Material Necessary for Each Spare
See Section 2.C.
E. Reidentified Parts
Not applicable.
F. Special Tooling
Not applicable.
3. Accomplishment Instructions
A. Preliminary work steps:
NOTE If the transmission oil is drained into a clean container, it can be reused.
(1) Remove lower transmission cover i.a.w. AMM, 63-21-00, 4-13.
B. Secure attachment screws (1, Figure 1) using locking washers (7):
(1) Measure clearance , Figure 1 between bearing outer race (2) and transmission
housing at four positions offset by 90 degrees using a feeler gauge:
(a) If the measured maximum clearance is less than or equal to 0.1 mm, proceed i.a.w.
Section 3.B.(3).
(b) If the measured maximum clearance is more than 0.1 mm, the difference between
the smallest and the biggest clearance must be determined:
– If the difference is less than 0.4 mm, proceed i.a.w. Section 3.B.(2).
– If the difference is equal to or more than 0.4 mm, the bearing must be
replaced. To do so, send main transmission to the manufacturer for repair.

### Page 6

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 4 of 6 REVISION 02, 2008-09-12
2008-09-10
WARNING IF SCREWS ARE MISSING, SEARCH AND FIND THEM.
NOTE Not damaged screws can be reused.
(2) Lift helicopter i.a.w. AMM, 07–00–00, 2–1 until landing gear is relieved.
(3) Torque–tighten all screws to 9 Nm.
(4) Successively put a locking washer (7) under all 8 screws i.a.w. Figure 1.
(5) Crosswise torque–tighten all screws to 9 Nm.
(6) Bend all locking washers i.a.w. Figure 1.
(7) Measure clearance , Figure 1 between bearing outer race (2) and transmission
housing using a feeler gauge. The clearance has to be less or equal to 0.05 mm.
C. Conclusive work:
NOTE If the O–ring on the lower transmission cover is not damaged, it can be
reused once.
(1) Install lower transmission cover i.a.w. AMM, 63-21-00, 4-13.
(2) Replenish oil i.a.w. AMM, 63-21-00, 3-2.
(3) Copy reply form sheet on page 6, fill out and send to ECD customer support 
Fax: +49–906–71–4111 or 
E–Mail: maintransmission@eurocopter.com
D. Confirm accomplishment of this Alert Service Bulletin by an entry in the log card of the main
transmission.
– ASB EC135-63A-013, Rev.02 accomplished, all screws secured by means of
locking washers.
4. Appendix
Not applicable.

### Page 7

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 5 of 6
2008-09-10
REVISION 02, 2008-09-12
Lower Hub–Shaft Bearing
Figure 1
1 Attachment screw
2 Bearing outer race
3 Roller bearing
4 Hub–shaft nut
5 Retainer ring
6 Ball bearing
7 Locking washer LN9023 B6 / A6
Measure clearance of bearing outer race to the housing at four positions using a
feeler gauge
1
 2 3 4 5
6
7

### Page 8

ALERT SERVICE BULLETIN
EC135
EC135-63A-013
PAGE 6 of 6 REVISION 02, 2008-09-12
2008-09-10
Reply form sheet for ASB EC135-63A-013 “Attachment of screws of the lower hub–shaft
bearing”
Completely fill out this form sheet and send by FAX to +49 906 714111 or by email to
maintransmission@eurocopter.com.
Please copy page! Original remains in Alert Service Bulletin!
Loose screws? No Yes Number
Customer Contact (Name) Telephone
Telefax
E–Mail
Operator
Helicopter S/N Helicopter Total Time TT
Main transmission S/N
Important data regarding helicopter
 Important data regarding main transmission
Main transmission TT
Main transmission TSOMain transmission P/N
Printed name
ASB EC135-63A-013 Revision 02 accomplished
Date Signature
Dropped out screws?
Remarks:
Address for material kit EC135-63-011-2C3 (see Section 2.B. of the ASB)
3
5
8
7
2
1
46
Mark position:
Secured with 8 locking washers?
LH RH
No Yes Number
No Yes
FLIGHT DIRECTION

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
