# Airbus Helicopters Alert Service Bulletin EC135-64A-007

Copy: No revision named ("Airbus Helicopters ASB EC135-64A-007 Rev 0"), 30 pages: PDF https://openairdocs.org/files/sha256/50/db/50db6b4e52fbe258b8a9745a06db9752e0ef06c07d78de3d7d742be8de880b15; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-64a007/file/50db6b4e52fb.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0380, the docket of AD 2021-16-10. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135-64A-007
- Latest revision known: EC135-64A-007, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-64a007

## Text (30 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0380, the docket of AD 2021-16-10. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Valid for Version(s): T1, T2, T2+, T3, P1, P2,
P2+, P3, 635 T1, 635 12+, 635 13, 635 P2+,
635 P3
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
TAIL ROTOR - Tail rotor blade
Inspection of the drain hole alignment of the blade assy
For the attention of
Revision No.  Date of issue
Revision O  2020-11-11
Summary:
With this Alert Service Bulletin (ASB), Airbus Helicopters prescribes a one-time inspection of the
drain hole alignment of the blade assy.
Compliance:
It is mandatory to obey this ASB.
Revision 0, 2020-11-11  PAGE 1 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
1  PLANNING INFORMATION
1.A EFFECTIVITY
1.A.1 Helicopters/installed equipment and parts
a) ЕC135 T1, T2, T2+, T3, P1, P2, P2+, P3, 635 T1, 635 T2+, 635 T3, 635 P2+, 635 P3,
S/N 0001 up to S/N 1999*.
* On the S/N 0886 the inspection of the drain hole alignment of the blade assy is accomplished in
the serial production but needs to be done again if the blade assy has been replaced in service.
b) Blade assy**  P/N L642A2002101
P/N L642A2002103
P/N L642A2002104
P/N L642A2002111
P/N L642A2002112
** On the excluded S/N, as shown in Section 4.B, the inspection of the drain hole alignment of
the blade assy has been accomplished in the serial production. These blade assys have been
considered as category A as shown in Table 1.
View A
Drain hole
Blade assy root  Blade assy
Affected area
Location of the blade assy drain hole
Figure 1
1.A.2 Non-installed equipment and parts
See Section 1.A.1.b.
1.B  ASSOCIATED REQUIREMENTS
It is recommended to accomplish ASB EC135-64A-006 or ASB EC135H-64A-001 prior
to this ASB.
PAGE 2 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
1.C  REASON
This ASB introduces a one-time inspection for drain hole alignment of the Fenestron
blade assembly. This ASB has been introduced following an airworthiness
investigation on the EC130 and the requirement has been transferred to the EC135
based on the similarities in the production method. Additionally with this ASB, limits
on repair details in AMM 64-22-00, 6-4 have been introduced (no further repairs are
allowed in the affected area of the blade assy root).
1.D  DESCRIPTION
Inspect the drain hole alignment of the blade assy. Replace the blade assy if
required.
1.E COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
The inspection of the drain hole alignment of the blade assy and the replacement of
the blade assy (if required) must be accomplished in accordance with Section 3.B.2
of this ASB before delivery of the helicopter.
Non-installed equipment and parts:
The inspection of the drain hole alignment of the blade assy and the replacement of
the blade assy (if required) must be accomplished in accordance with Section 3.B.5
of this ASB before delivery or installation.
Revision 0, 2020-11-11  PAGE 3 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
1.E.2 Compliance in service
Helicopters/installed equipment and parts:
Part I: Examine the blade assy documents
Examine the blade assy documents and forecast the compliance time of Part Il in
accordance with Section 3.B.1 of this ASB within the next 50 Fh or 18 months
whichever occurs first after receipt of this ASB.
Part I
The blade assy has
been operated on a
No
EC135 T3 / TH / P3
/ РЗН / EC635 T3 /
ТЗН / PЗ / РЗН
helicopter?
Yes
TSN of the  TSN of the
No  No
blade assy  blade assy
is ≤ 1000  is ≤ 2000
Fh?  Fh?
Yes  Yes
Forecast the  Forecast the  Forecast the  Forecast the
compliance time of  compliance time of  compliance time of  compliance time of
Part Il as follows:  Part Il as follows:  Part Il as follows:  Part Il as follows:
Comply with Part II  Comply with Part II  Comply with Part II  Comply with Part II
before the TSN of  within the next  before the TSN of  within the next
the blade assy  200 Fh or 18  the blade assy  400 Fh or 18
reaches 1200 Fh or  months whichever  reaches 2400 Fh or  months whichever
within the next 18  occurs first after  within the next 18  occurs first after
months whichever  receipt of this ASB.  months whichever  receipt of this ASB.
occurs first after  occurs first after
receipt of this ASB  receipt of this ASB.
End of
Part I
PAGE 4 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Part II: Inspect the drain hole alignment of the blade assy
After accomplishment of Part I of this ASB inspect the drain hole alignment of the
blade assy and replace the blade assy (if required) in accordance with Section 3.B.2
of this ASB within the forecasted compliance time.
Part Il
No
Distance A > 0.1 mm?
(as shown in
Figure 4)
Yes
Distance B ≥ 2.2 mm?  No
(as shown in
Figure 4)
Yes
Distance C ≤ 4.7 mm?  No
(as shown in
Figure 4)  Consider the blade assy
as category B as shown in
Table 1.
y Yes
Consider the blade assy  Replace the blade assy.
as category A as shown in
Table 1.
End of
Part I|
Revision 0, 2020-11-11  PAGE 5 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Non-installed equipment and parts:
Part I and Part II
The inspection of the drain hole alignment of the blade assy and the replacement of
the blade assy (if required) must be accomplished in accordance with Section 3.B.5
of this ASB before installation but latest 18 months after receipt of this ASB.
1.F  APPROVAL
Approval of this document:
The technical content of this document is approved under the authority of
DOA No. EASA.21J.700.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others*
Part I: Examine the blade assy documents
Estimated
approx. 2 h
Man-hours
Part II: Inspect the drain hole alignment of the blade assy
approx. 2 h
(inspection)  approx. 2 h
Estimated
Man-hours**  approx. 8 h  (replacement,  approx. 3 h
(replacement,  if required)
if required)
* CAMO (or equivalent)
** Based on installed tail rotor head assy
1.H  WEIGHT AND BALANCE
No effect on weight and balance.
POWER CONSUMPTION
Not affected.
1.J  SOFTWARE UPGRADES/UPDATES
Not changed.
1.K  REFERENCES
AMM EC135/635.
1.L  OTHER AFFECTED PUBLICATIONS
Not affected.
PAGE 6 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
Not affected.
Mixability:
Not affected.
Revision 0, 2020-11-11  PAGE 7 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
None.
2.B  LOGISTIC INFORMATION
None.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
Consumables to be ordered separately:
WARNING
RESPECT THE SAFETY DATA SHEET OF THE
MANUFACTURER.
No.  Keyword  Qty.  Specification **  Rem.
(approx.)
1  Cleaning agent  a.n.*  201
* a.n. = as needed.
** For specification, refer to AMM 01-00-00, 2-1.
The consumables can be ordered separately from the following companies.
Aviatec global aviation  BDSI
Website: https://www.aviatec.net  Website: https://www.boeingdistribution.com
Telephone: +33 1.34.46.45.24 or  Telephone: +1.305.925.2600
+49 4193.8803.630  Fax: +1.305.507.7191
Fax:  +33 1.34.46.45.26 or  AOG: +1.305.471.8888
+49 4193.8803.699  AOG email: AOGdesk@boeingdistribution.com
AOG:  +49 4193.8803.660
AOG email: aog@aviatec.aero
Gaches chimie
Website: https://www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
PAGE 8 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Special tools (test equipment):
Keyword  Qty.  Specification  Rem.
Ruler  1  Commercial available
Smartphone
or
Digital camera  1  Commercial available
and
PC or Laptop
Remark:
A = With Artificial Image Recognition for Blade (A.I.R Blade) app version V1 for
EC135/635 installed. For the user manual and additional information see
IN 3583-1-64.
B = With specific Microsoft PowerPoint file version V1 for EC135/635 installed.
For the user manual and additional information see IN 3583-1-64.
2.D  MATERIAL TO BE RETURNED
None.
Revision 0, 2020-11-11  PAGE 9 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
Obey the "General recommendations for Working at helicopter"
(AMM 03-10-02, 2-1).
З.В  WORK STEPS
Part I: Examine the blade assy documents
3.B.1 Examination of the blade assy documents
NOTE  The blade assy is listed in the log card of the tail rotor head assy.
1. Examine the documents of each individual blade assy to determine the Time
Since New (TSN) of the blade assy.
NOTE  The load on the blade assy operated on a EC135 T3 / EC135 TЗH /
ЕС135 PЗ / ЕС135 РЗН / ЕС635 Т3 / ЕС635 ТЗН / ЕС635 PЗ /
ЕС635 РЗН helicopter is higher.
2. Examine the documents of each individual blade assy to determine if it has been
operated on a EC135 T3 / EC135 ТЗН / EC135 PЗ / ЕC135 P / EC635 T3 /
EC635 ТЗН / EC635 P3 / ЕC635 PH helicopter.
3. Use the flowchart in Section 1.E.2 to forecast the compliance time of Part II.
4. Proceed in accordance with Section 3.C to confirm accomplishment of Part I.
PAGE 10 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Part II: Inspect the drain hole alignment of the blade assy
3.B.2  Inspection of the drain hole alignment of the blade assy
NOTE  This procedure is to be carried out for each individual blade assy.
NOTE  It is recommended that two persons accomplish this procedure, if
the blade assy is installed.
NOTE  There are two possible procedures for the inspection of the drain
hole alignment of the blade assy:
- Inspection with the A..R Blade app version V1 for EC135/635.
- Inspection with picture and specific Microsoft PowerPoint file
version V1 for EC135/635.
NOTE  For the user manual and additional information for the possible
procedures see IN 3583-1-64.
1. Clean the area around the drain hole (2, Fig. 2) with cleaning agent (CM 201).
NOTE  The drain hole alignment of the blade assy can be inspected from
the left and right side of the helicopter.
2. If required, move the yaw pedal (left or right) as required to expose the drain
hole (2, Fig. 2).
3. Temporary mark the blade assys (1, Fig. 2) in the area of the drain hole (2) for
identification (e.g. with numbers from one to ten or with the S/N of the blade
assy (1)).
4. Position the ruler (4, Fig. 2) perpendicular and adjacent to the trailing edge (3) as
shown in Figure 2.
Revision 0, 2020-11-11  PAGE 11 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Position of the ruler correct
4
90°  90°
View A  View B
2
- 3
Position of the ruler not correct  3
150°
140°
View C  View D
3
1 Blade assy  P/N L642A2002101 or P/N L642A2002103
or P/N L642A2002104 or P/N L642A2002111
or P/N L642A2002112
2 Drain hole
3 Trailing edge
4 Ruler 1
• Perpendicular and adjacent to the trailing edge.
Position of the ruler
Figure 2
PAGE 12 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
5. Position the smartphone or digital camera (5, Fig. 3) perpendicular to the drain
hole (2) and parallel to the trailing edge (3) of the blade assy (1) as shown in
Figure 3.
A CAUTION
TEST RESULTS CAN BE INFLUENCED WITH ANY OF
THE FOLLOWING FACTORS:
- BRIGHTNESS IS NOT SUFFICIENT
- DRAIN HOLE IS NOT IN FOCUS
- ZOOM IS NOT APPROPRIATE.
6. Take a picture of the drain hole (2, Fig. 3) of the blade assy (1).
90°
5
Blade assy installed  Blade assy not installed
1 Blade assy  P/N L642A2002101 or P/N L642A2002103
or P/N L642A2002104 or P/N L642A2002111
or P/N L642A2002112
2 Drain hole
3 Trailing edge
4 Ruler
5 Smartphone or digital camera /1
Perpendicular to the drain hole and parallel to the trailing edge of the blade assy.
Recommended smartphone or digital camera position to take a picture
Figure 3
Revision 0, 2020-11-11  PAGE 13 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
7. Measure the distance A, B and C and examine each individual blade assy:
a. Measure distance A, the minimum remaining rib thickness of the blade assy
(1, Fig. 4), as shown in Figure 4.
b. Compare the results with Table 1.
- If the results are within the limits of category A, proceed in accordance
with Section 3.B.2.7.c.
- If the results are not within the limits of category A, consider the blade
assy (1, Fig. 4) as category B. Proceed in accordance with Section 3.B.4.
- If the results cannot be confirmed, proceed in accordance with
Section 3.B.3.
c. Measure distance B, the rib thickness of the blade assy (1, Fig. 4) on the
center line (4) of the drain hole (2), as shown in Figure 4.
d. Compare the results with Table 1.
- If the results are within the limits of category A, proceed in accordance
with Section 3.B.2.7.e.
- If the results are not within the limits of category A, consider the blade
assy (1, Fig. 4) as category B. Proceed in accordance with Section 3.B.4.
- If the results cannot be confirmed, proceed in accordance with
Section 3.B.3.
e. Measure distance C, between the center line (4, Fig. 4) of the drain hole (2)
and the shoulder (5) of the blade assy (1), as shown in Figure 4.
f. Compare the results with Table 1.
- If the results are within the limits of category A, consider the blade assy
(1, Fig. 4) as category A and remove the temporary mark from the blade
assy (1). Proceed in accordance with Section 3.C.
- If the results are not within the limits of category A, consider the blade
assy (1, Fig. 4) as category B. Proceed in accordance with Section 3.B.4.
- If the results cannot be confirmed, proceed in accordance with
Section 3.B.3.
PAGE 14 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Category A  Category B
(compliant blade assy)  (non-compliant blade assy)
Distance A is more than 0.1 mm.  Distance A is less than or equal to
0.1 mm.
and  or
Distance B is more than or equal to  Distance B is less than 2.2 mm.
2.2 mm.
and  or
Distance C is less than or equal to  Distance C is more than 4.7 mm.
4.7 mm.
Blade assy categories
Table 1
Revision 0, 2020-11-11  PAGE 15 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
1 Blade assy  P/N L642A2002101 or P/N L642A2002103
or P/N L642A2002104 or P/N L642A2002111
or P/N L642A2002112
2 Drain hole
3 Countersunk
4 Center line
5 Shoulder
/ 1 Values for blade assy category A as shown in Table 1.
2
View
2  > 0.1 mm 1
≥ 2.2 mm /1
C
≤ 4.7 mm 1
C
≤ 4.7 mm /1
Inspection of the drain hole alignment of the blade assy
Figure 4
PAGE 16 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
3.B.3 Contact Airbus Helicopters to request support
1. Send the picture of the blade assy (1, Fig. 4) to Airbus Helicopters.
a. With WebTEK access:
- Create a Technical Event (TE) on WebTEK:
https://keycopter.airbushelicopters.com
- Select the TE business domain: "ASB Fenestron Blade"
- Insert the title: "Support request for ASB EC135-64A-007 Revision 0"
- Attach the picture of the blade assy (1, Fig. 4).
- Send the TE.
b. Without WebTEK access:
- Send the picture of the blade assy (1, Fig. 4) to:
customersupport.helicopters@airbus.com
2. Continue as detailed in the support feedback received from Airbus Helicopters.
3.B.4 Replacement of the blade assy
1. If installed, remove the blade assy (1, Fig. 4) (AMM 64-22-00, 4-3).
2. Provide feedback to Airbus Helicopters.
a. With WebTEK access:
- Create a TE on WebTEK: https://keycopter.airbushelicopters.com
- Select the TE business domain: "ASB Fenestron Blade"
- Insert the title: "ASB EC135-64A-007 Revision 0 - Blade assy category B"
- Attach the picture of the blade assy (1, Fig. 4).
- Send the TE.
b. Without WebTEK access:
- Use the QR-Code:
or
- Copy, fill out and send back the reply form sheet on page 20.
Revision 0, 2020-11-11  PAGE 17 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 18 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
3. Discard the blade assy (1, Fig. 4).
4. If removed, install a serviceable blade assy (1, Fig. 4) (AMM 64-22-00, 4-4).
3.B.5 Work steps for non-installed equipment or parts
Stock retrofitting:
Inspect the blade assy in accordance with Section 3.B.2.
З.С  COMPLIANCE CONFIRMATION
Compliance with this document:
Part I: Examine the blade assy documents
Confirm accomplishment of Part I of this ASB by an entry in the historical record of
the helicopter.
Part II: Inspect the drain hole alignment of the blade assy
Confirm accomplishment of Part II of this ASB by an entry in the historical record of
the helicopter.
Part I and Part II
Record full compliance with this ASB, with the revision number, in the helicopter
documents.
Record full compliance with this ASB, with the revision number, in the log card of the
equipment (if a log card exists).
Please confirm compliance with this ASB (see IN 3447-1-00 for details):
QR-Code or hypertext link
NOTE
The recording of compliance with ASBs in the R-Tex
tool does not replace the recording in the helicopter
documents
ASB EC135-64A-007
PAGE 18 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 19 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
None.
Maintenance instructions:
NOTE  Repair in the affected area of the blade assy root (Fig. 1) that was
done prior to this ASB is examined with this ASB.
Repair in the affected area of the blade assy root (Fig. 1) in accordance with
AMM 64-22-00, 6-4 is not permitted.
NOTE  The pre-print of the inspection - tail rotor blade
(AMM 64-22-00, 6-4) is published on ORION.
Until the distribution of the AMM EC135/635 containing the new instructions, the
inspection - tail rotor blade (AMM 64-22-00, 6-4) must be used as shown in
Section 4.C.
Revision 0, 2020-11-11  PAGE 19 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 20 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
APPENDIX
4.A  Reply form sheet
Reply form sheet
for ASB EC135-64A-007 Revision Inspection of the drain hole alignment of the blade
assy"
Please completely fill out reply form sheet and send it to the given e-mail.
To
Airbus Helicopters
Customer Support
e-mail: customersupport.helicopters@airbus.com
Tail rotor head assy
P/N  S/N  TSN
(Fh)
Blade assy
P/N  S/N  TSN  Distance A  Distance B  Distance C  Category
(Fh)  (mm)  (mm)  (mm)
B
B
B
B
B
Date:  Signature:
Please copy page! Original page remains in Alert Service Bulletin!
PAGE 20 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 21 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
4.B  Exluded S/N of the blade assy
Excluded S/N of the blade assy
On the excluded S/N the inspection of the drain hole alignment of the blade assy has been
accomplished in the serial production. These blade assys have been considered as
category A as shown in Table 1.
M18523  M18953  M19208  M19364  M20059  M20303  M20665  M20712
M18525  M18954  M19214  M19366  M20078  M20304  M20669  M20713
M18532  M18958  M19218  M19368  M20079  M20305  M20670  M20714
M18533  M18959  M19221  M19374  M20081  M20306  M20671  M20715
M18537  M18960  M19233  M19391  M20083  M20307  M20674  M20716
M18541  M19086  M19238  M19396  M20085  M20308  M20676  M20717
M18545  M19113  M19240  M19463  M20087  M20309  M20678  M20762
M18546  M19118  M19241  M19579  M20095  OTEOZW  6290ZW  LELOZW
M18549  M19119  M19242  M19599  M20098  ZIEOZW  0890ZW  M20803
M18552  M19120  M19243  M19632  M20099  M20313  M20681  M20821
M18555  M19121  M19244  M19724  M20103  M20314  M20682  M20830
M18556  M19124  M19246  M19730  M20105  M20315  M20683  M20836
M18884  M19125  M19247  M19735  M20106  M20316  M20684  M20839
M18889  M19127  M19251  M19736  M20109  M20317  M20685  M20845
M18914  M19130  M19252  M19737  M20111  M20318  989W  M20851
M18917  M19134  M19253  M19738  M20113  M20334  M20687  2O00EW
M18919  M19136  M19256  M19743  M20126  8890ZW  6000EW
M18921  M19138  M19258  M19752  M20180  M20339  M20689  M30029
M18922  M19139  M19259  M19755  M20280  M20341  M20690  M30040
M18923  M19141  M19260  M19867  M20281  THEONE  M20691  M30042
M18924  M19145  M19261  M19874  M20282  M20454  M20692  M30046
M18925  M19147  M19263  M19882  M20283  M20467  M20693  M30047
M18926  M19150  M19264  M19892  M20284  M20469  M30050
M18927  M19151  M19265  M19893  M20285  ELDOZW  S690ZW  M30052
M18928  M19152  M19266  M19901  M20286  M20477  M20696  M30055
M18931  M19156  M19267  M19910  M20287  M20567  M20697  M30059
M18932  M19158  M19269  M19954  M20288  M20572  M20698  M30060
M18934  M19161  M19270  M19965  M20290  M20599  M20699  M30065
M18937  M19162  M19271  M19970  M20291  M20610  M20700  M30067
M18938  M19164  M19273  M19971  M20292  M20627  M20701  M30074
M18939  M19169  M19276  M19979  M20293  M20630  M20702  M30079
M18941  M19174  M19284  M19981  M20294  M20639  M20703  M30094
M18943  M19182  M19290  M19983  M20295  M20642  M20704  M30101
M18944  M19185  M19304  M19985  M20296  M20646  M20705  M30109
M18945  M19186  M19312  M19988  M20297  M20647  M20706  M30111
M18947  M19187  M19319  M19991  M20298  M20656  M20707  M30115
M18948  M19188  M19320  M19997  M20299  M20659  M20708  M30137
M18949  M19189  M19322  M20030  M20300  M20660  M20709  M30168
M18951  M19190  M19323  M20035  M20301  M20662  M20710  M30170
M18952  M19194  M19328  M20057  M20302  M20664  M20711  M30177
Revision 0, 2020-11-11  PAGE 21 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 22 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Excluded S/N of the blade assy
On the excluded S/N the inspection of the drain hole alignment of the blade assy has been
accomplished in the serial production. These blade assys have been considered as
category A as shown in Table 1.
M30178  M30496  M30633  M30850  M31097  M31181  M31222  M31383
M30182  M30517  M30634  M30852  M31098  M31182  M31223  M31384
M30189  M30535  M30636  M30854  M31099  M31183  M31224  M31385
M30192  M30549  M30637  M30855  M31100  M31184  M31225  M31386
M30210  M30551  M30638  M30856  M31101  M31185  M31226  M31387
M30211  M30553  M30639  M30857  M31102  M31186  M31227  M31390
M30221  M30592  M30683  M30860  M31104  M31188  M31228  M31391
M30226  M30600  M30688  M30861  M31105  M31189  M31229  M31392
M30228  M30601  M30692  M30862  M31106  M31190  M31230  M31393
M30239  M30602  M30696  M30864  M31108  M31191  M31231  M31394
M30283  M30603  M30700  M30868  M31109  M31192  M31232  M31395
M30285  M30604  M30713  M30871  M31110  M31193  M31233  M31396
M30309  M30605  M30714  M30872  M31111  M31194  M31234  M31397
M30313  M30606  M30719  M30873  M31112  M31195  M31235  M31398
M30329  M30607  M30800  M30874  M31113  M31196  M31236  M31399
M30401  M30608  M30801  M30876  M31114  M31197  M31237  M31400
M30402  M30609  M30804  M30877  M31115  M31198  M31238  M31401
M30403  M30610  M30805  M30878  M31116  M31199  M31239  M31402
M30404  M30611  M30808  M30892  M31117  M31200  M31360  M31403
M30405  M30612  M30810  M30899  M31118  M31201  M31361  M31404
M30406  M30613  M30812  M30903  M31119  M31202  M31362  M31405
M30407  M30614  M30816  M30913  M31131  M31203  M31363  M31406
M30408  M30615  M30819  M31059  M31160  M31204  M31364  M31407
M30410  M30616  M30820  M31065  M31161  M31205  M31365  M31408
M30411  M30617  M30822  M31080  M31162  M31206  M31366  M31409
M30413  M30618  M30825  M31082  M31163  M31207  M31367  M31410
M30415  M30619  M30826  M31083  M31164  M31208  M31368  M31411
M30419  M30620  M30827  M31084  M31165  M31209  M31369  M31412
M30421  M30621  M30828  M31085  M31166  M31210  M31370  M31413
M30425  M30622  M30831  M31086  M31167  M31211  M31371  M31414
M30428  M30623  M30832  M31087  M31168  M31212  M31372  M31415
M30429  M30624  M30838  M31088  M31172  M31213  M31373  M31416
M30430  M30625  M30840  M31089  M31173  M31214  M31374  M31417
M30431  M30626  M30841  M31090  M31174  M31215  M31375  M31418
M30434  M30627  M30842  M31091  M31175  M31216  M31376  M31419
M30436  M30628  M30843  M31092  M31176  M31217  M31377  M31420
M30437  M30629  M30844  M31093  M31177  M31218  M31378  M31421
M30439  M30630  M30847  M31094  M31178  M31219  M31380  M31422
M30443  M30631  M30848  M31095  M31179  M31220  M31381  M31423
M30485  M30632  M30849  M31096  M31180  M31221  M31382  M31424
PAGE 22 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 23 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
Excluded S/N of the blade assy
On the excluded S/N the inspection of the drain hole alignment of the blade assy has been
accomplished in the serial production. These blade assys have been considered as
category A as shown in Table 1.
M31425  M31557  M31718  M31879  M31919  M32079  M32119  M32199
M31426  M31558  M31719  M31880  M32040  M32080  M32160  end of list
M31427  M31559  M31840  M31881  M32041  M32081  M32161
M31428  M31680  M31841  M31882  M32042  M32082  M32162
M31429  M31681  M31842  M31883  M32043  M32083  M32163
M31430  M31682  M31843  M31884  M32044  M32084  M32164
M31431  M31683  M31844  M31885  M32045  M32085  M32165
M31432  M31684  M31845  M31886  M32046  M32086  M32166
M31433  M31685  M31846  M31887  M32047  M32087  M32167
M31434  M31686  M31847  M31888  M32048  880ZEW
M31435  M31687  M31848  M31889  M32049  M32089  M32169
M31436  M31688  M31849  M31890  M32050  M32090  M32170
M31437  M31689  M31850  M31891  M32051  M32091  M32171
M31438  M31690  M31851  M31892  M32052  M32092  M32172
M31439  M31691  M31852  M31893  M32053  M32093  M32173
M31520  M31692  M31854  M31894  M32054  M32094  M32174
M31521  M31693  M31855  M31895  M32055  S6OZEW  M32175
M31525  M31694  M31856  M31896  M32056  960ZEW  M32176
M31526  M31695  M31857  M31897  M32057  L6OZEW  M32177
M31527  M31696  M31858  M31898  M32058  860ZEW  M32178
M31534  M31697  M31859  M31899  M32059  660ZEW  M32179
M31536  M31698  M31860  M31900  M32060  M32180
M31537  M31699  M31861  M31901  M32061  TOTTEN  M32181
M31539  M31700  M31862  M31902  M32062  M32102  M32182
M31540  M31701  M31863  M31903  M32063  EOTZEW  M32183
M31541  M31702  M31864  M31904  M32064  FOIZEW  M32184
M31542  M31704  M31865  M31905  M32065  M32105  M32185
M31543  M31705  M31866  M31906  M32066  M32106  M32186
M31544  M31706  M31867  M31907  M32067  M32107  M32187
M31545  M31707  M31868  M31908  M32068  M32108  M32188
M31546  M31708  M31869  M31909  M32069  M32109  M32189
M31547  M31709  M31870  M31910  M32070  M32110  M32190
M31548  M31710  M31871  M31911  M32071  M32111  M32191
M31550  M31711  M31872  M31912  M32072  M32112  M32192
M31551  M31712  M31873  M31913  M32073  M32113  M32193
M31552  M31713  M31874  M31914  M32074  M32114  M32194
M31553  M31714  M31875  M31915  M32075  M32115  M32195
M31554  M31715  M31876  M31916  M32076  M32116  M32196
M31555  M31716  M31877  M31917  M32077  M32117  M32197
M31556  M31717  M31878  M31918  M32078  M32118  M32198
Revision 0, 2020-11-11  PAGE 23 of 24
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 24 (OCR)

AIRBUS  HELICOPTERS
ASB EC135-64A-007
4.C  Pre-print of the inspection - tail rotor blade (AMM 64-22-00, 6-4)
PAGE 24 of 24  Revision 0, 2020-11-11
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 25

Aircraft Maintenance Manual (AMM) EC135
Tail Rotor - Inspection
EFFECTIVITY ALL
6-4 Inspection - Tail Rotor Blade
A. References:
INTRODUCTION
18-11-00, 5-1 ................................. Dynami c Balancing - Tail Rotor
20-00-00, 2-18 ............................... Applica tion Procedure - Varnish CM 515
64-22-00, 4-4 ................................. Assemb ly - Tail Rotor
64-22-00, 8-1 ................................. Repair - Tail Rotor Blade
64-22-00, 8-4 ................................. Bondin g - Balancing Weight Bushing in the Blade Root
B. Special Tools:
None.
C. Consumable Materials:
CM 515 ......................................... Varni sh
Commercial ................................... Abrasive Paper (grain 400)
D. Routine Replacement Parts:
None.
E. Job Set-up:
(1) None.
F. Procedure:
CAUTION WHEN YOU DO WORK ON "CRITICAL PARTS ( CP)" AND "IMPORTANT
PARTS ( IP)", OBEY THE RELATED INSTRUCTIONS IN THE
(INTRODUCTION).
(1) Do the inspection of the tail rotor blade CP (1, Figure 601 ) as follows:
(a) Examine the tail rotor blade CP (1) for:
- Cracks
- Mechanical damage
- Corrosion
- Erosion
- Damage to the paint
- Wear of the black plasma layer on the bearing surfaces
- Correct installation of the balance weight bushing in the b lade root (2).
NOTE On the tip of the tail rotor blade CP (1), at the trailing edge
corner, a radius R Figure 602 of 0 mm to 5 mm (0 in to 0.196 in)
is permitted.
1 If there is a crack or if the damage is outside the permitted da mage and repair
Conf. Code: 000 64-22-00, 6-4 Page 601
2020.11.03
PRE PRINT

### Page 26

Aircraft Maintenance Manual (AMM) EC135
limits (Table 601), replace the tail rotor blade CP (1) (64-22-00, 4-4).
2 If there is mechanical damage and/or corrosion within the da mage and repair
limits (Table 601), repair the tail rotor blade CP (1) (64-22-00, 8-1).
3 If you find erosion on the blade leading edge, measure the bla de chord in the
area of maximum erosion damage.
a If the measured blade chord is less than 48.5 mm (1.90 in), rep lace the
tail rotor blade CP (1) (64-22-00, 4-4).
Zone ( Figure 602 ) Damage Limits (without repair) Repair Limits (repair possible)
A MAX radius of 2 mm (0.078 in) MAX radius of 2 mm (0.078 in)
B
Dent with MAX depth of 0.45 mm
(0.017 in)
Score with MAX depth of 0.45
mm (0.017 in)
MIN residual blade chord of 48.5
mm (1.91 in)
MAX length of 30 mm (1.181 in)
in blade span direction
C
Dent with MAX depth of 0.45 mm
(0.017 in)
Score with MAX depth of 0.45
mm (0.017 in)
MIN residual blade chord of 48.5
mm (1.91 in)
D
Score with MAX depth of 0.01
mm (0.0003 in)
Dent with MAX depth of 0.05 mm
(0.001 in)
Score with MAX depth of 0.05
mm (0.001 in)
MIN of 10 mm (0.394 in) in radius
transition
E
Dent with MAX depth of 0.1 mm
(0.0039 in)
MAX of 0.5 mm (0.019 in) of
diameter
Score with MAX depth of 0.01
mm (0.0003 in)
Score with MAX depth of 0.15
mm (0.005 in)
MIN distance of 2 mm (0.079 in)
between scores
Dent with MAX depth of 0.2 mm
(0.007 in) and MIN of 2 mm
(0.079 in) of distance between
dents
F
MAX of 10 % of the varnish
surface
On the plasma layer, damage up
to a maximum diameter of 2 mm
(0.078 in) or with a maximum
surface of 3 mm
2
(0.004 in
2
) on
the plasma layer
On the plasma layer, MIN
distance of 7 mm (0.276 in)
between damage and not more
than 10 damages on each bearing
surface
G Scratch with MAX depth of 0.1mm (0.0039 in) Scratch with MAX depth of 1 mm(0.039 in)
Conf. Code: 000 64-22-00, 6-4 Page 602
2020.11.03
PRE PRINT

### Page 27

Aircraft Maintenance Manual (AMM) EC135
Zone ( Figure 602 ) Damage Limits (without repair) Repair Limits (repair possible)
H
For any anomalies found on the
Upper and Lower surface,
including the rib and the drain
hole contact your local Airbus
representative.
No repair is permitted
ØA MAX diameter of 14.53 mm(0.572 in)
ØB MAX diameter of 13.53 mm(0.532 in)
Table 601 Damage and Repair Limits
CAUTION RISK OF DAMAGE TO THE HUB BODY (4, FIGURE 601 ). IF YOU
DO NOT APPLY THE VARNISH CORRECTLY, YOU CAN CAUSE
DAMAGE TO THE HUB BODY (4). MAKE SURE YOU APPLY THE
VARNISH CORRECTLY.
CAUTION RISK OF DAMAGE TO THE HUB BODY (4). IF YOU DO NOT KEEP
THE MINIMUM DIMENSION X AND DIMENSION Y, DAMAGE TO
THE HUB BODY (4) CAN OCCUR. MAKE SURE YOU KEEP THE
MINIMUM DIMENSION X AND DIMENSION Y.
(b) If the damage to the varnish in Zone F Figure 602 on the bearing races is outside
the damage and repair limits (Table 601), apply Varnish CM 51 5 to the damaged
area (20-00-00, 2-18).
1 Make sure that the thickness of the layer of Varnish CM 515 is b etween 0.007
mm and 0.015 mm (0.0003 in and 0.0005 in).
2 Make sure that the dimension X on the inner bearing ring (5, Figure 601 ) is a
minimum of 0.7 mm (0.028 in).
3 Make sure that the dimension Y on the outer bearing ring (3) is a minimum of
0.8 mm (0.032 in).
CAUTION RISK OF DAMAGE TO THE METAL SURFACE OF THE BLADE
ROOT (2). IF YOU DO NOT REMOVE THE LAYER OF VARNISH
CAREFULLY YOU CAN CAUSE DAMAGE TO THE METAL
SURFACE OF THE BLADE ROOT (2). MAKE SURE YOU DO NOT
CAUSE DAMAGE TO THE METAL SURFACE OF THE BLADE
ROOT (2) WHEN YOU REMOVE THE LAYER OF VARNISH.
(c) If the dimension X and the dimension Y are less than the min imum distances,
carefully remove Varnish CM 515 with Abrasive Paper (grain 4 00).
NOTE If the balance weight bushing is loose, it can rotate in the bl ade root (
2).
NOTE If you cannot remove the balance weight bushing with your han d, you
can use the tail rotor blade CP (1) again.
Conf. Code: 000 64-22-00, 6-4 Page 603
2020.11.03
PRE PRINT

### Page 28

Aircraft Maintenance Manual (AMM) EC135
(d) Bond the loose balance weight bushing (64-22-00, 8-4).
(e) Install the tail rotor blades CP (1, Figure 602 ) repaired to the maximum permitted
limits or damaged in the area X of Zone E as follows:
1 If two tail rotor blades CP (1) have equivalent repair conditions, install these tail
rotor blades CP (1) opposite to each other (64-22-00, 4-4).
2 If more than two tail rotor blades CP (1) have equivalent repair conditions,
install these tail rotor blades CP (1) with equal distance between them
(64-22-00, 4-4).
(f) Install the remaining tail rotor blades CP (1) (64-22-00, 4-4).
(2) If the blades are replaced or if they change positions, do the balance of the tail rotor
(18-11-00, 5-1).
G. Close-up:
(1) Remove all tools and other materials and clean the work ar ea.
Conf. Code: 000 64-22-00, 6-4 Page 604
2020.11.03
PRE PRINT

### Page 29

Aircraft Maintenance Manual (AMM) EC135
C1356422M104400MU02
B
Y
CX
A
B
C
A−A
A
A
A
2
3
4
5 1
Inspection - Tail Rotor Blade
Figure 601
Conf. Code: 000 64-22-00, 6-4 Page 605
2020.11.03
PRE PRINT

### Page 30

Aircraft Maintenance Manual (AMM) EC135
ØB
B
C
C1356422M100900MU02
A
A
B
ZONE B
ØB
ØA
C
ZONE A
ZONE D
ZONE C
ZONE F
ZONE E
150 mm
(5.905 in)
1 mm
(0.039 in)
50 mm
(1.968 in)
ØA
R 0−5 mm(0.0196 in)
ZONE H
ZONE G
1
1
Inspection - Tail Rotor Blade
Figure 602
Conf. Code: 000 64-22-00, 6-4
END OF MODULE
Page 606
2020.11.03
PRE PRINT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
