# Eurocopter Alert Service Bulletin EC135-67A-012

Copy: Revision 1 ("U.S. DOT/FAA - Service Bulletin"), 14 pages: PDF https://openairdocs.org/files/sha256/02/2b/022b02c5be9029b8502c4262039800ed0d2347ff14131409d879904030426b4d; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-67a012/file/022b02c5be90.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0446; AD 2013-21-05, 2013-21-05 R1 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135-67A-012
- Latest revision known: EC135-67A-012, Revision 2, dated April 3, 2017 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-67a012

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-21-05 R1](https://openairdocs.org/ad/2013-21-05-R1.md), effective Dec 21, 2018: Revisions 1 and 2
- [AD 2013-21-05](https://openairdocs.org/ad/2013-21-05.md), effective Dec 5, 2013: Revision 1

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec135-67a012/proposed.md).

## Text (14 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0446; AD 2013-21-05, 2013-21-05 R1 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 1 of 14
2006-09-04
REVISION 01, 2006-10-18
Rotor Flight Control  –  Tail Rotor Controls  –  Inspection of linear
transducer (LVDT COLLECTIVE) bearing and modification of rod and
floor
1. Planning Information
A. Effectivity
(1) Helicopters affected: EC135, all models.
(2) Components affected: Bearing LN9367GE6N2
Rod L671M5040205
Lever L671M5040101
Floor L533M1014101 or
L533M1014102 or
L533M1014103 or
L533M1014104 or
L533M1014105 or
L533M1014106
(3) Spare Parts affected: Rod L671M5040205
Lever L671M5040101
Floor L533M1014101 or
L533M1014102 or
L533M1014103 or
L533M1014104 or
L533M1014105 or
L533M1014106
B. Concurrent Requirements
Not applicable.
C. Reason
ECD was informed of an incident in which an impaired controllability of the tail rotor was
detected. Examinations have shown that the bearing of the linear transducer was subject
to binding and the control range was limited. With this Alert Service Bulletin an inspection
and, if necessary, the replacement of the linear transducer bearing and the modification of
the rod (21, Figure 1) and the floor shall be accomplished.
D. Description
Inspect bearing of the linear transducer and the lower side of the floor. If there is binding
and/or chafing on the floor, replace bearing.
Modify rod and floor.

### Page 2

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 2 of 14 REVISION 01, 2006-10-18
2006-09-04
E. Compliance
(1) Accomplish inspection and, if necessary, replacement of the bearing as well as
modification of floor i.a.w. Section 3.A. up to and including Section 3.G. of this Alert
Service Bulletin by 31.10.2006 at the latest.
(2) Modification of rod i.a.w. Section 3.H. of this Alert Service Bulletin must be
accomplished with the next periodical inspection (800 fh) at the latest.
(3) In future, the inspection of the bearing must be repeated with every periodical
inspection (800 fh).
(4) Spare parts affected must be modified i.a.w. this Alert Service Bulletin before they are
installed in the helicopter at the latest.
F. Approval
The technical content of this document is approved under the authority of
DOA No. EASA.21J.034.
G. Manpower
– Approx. 10 man–hours for modification of rod and floor.
– Approx. 13 man–hours for modification of rod and floor as well as for replacement of
bearing.
H. Weight and Balance
Not applicable.
I. Electrical Load Data
Not applicable.
J. Software Accomplishment Summary
Not applicable.
K. References
AMM EC135.
L. Other Publications affected
The changes to AMM EC135, MSM EC135, AMM EC135/635 T1 (CPDS) and to
MSM EC135/635 T1 (CPDS) wich are required as a result of this Alert Service Bulletin will
be incorporated with one of the next revisions.
M. Interchangeability of Parts
Not applicable.

### Page 3

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 3 of 14
2006-09-04
REVISION 01, 2006-10-18
2. Material Information
A. Material – Price and Availability
Information on cost and availability of required kit EC135-67A-012-2.C will be provided by
ECD, Dept. Spares Order Administration on request.
B. Support Information
Not applicable.
C. Material Necessary for Each Helicopter
Retrofit kit EC135-67A-012-2.C.
No. New P/N Keyword Old P/N Qty Disposition
1 LN9367GE6N2 Bearing LN9367GE6N2 1 A, C
2 EN2367/C026214018 Cotter pin EN2367/C026214018 1 A
3 LN9025/C02620615L Washer − 1 A
4 LN94/C026215018 Cotter pin LN94/C026215018 2 A
5 ABS0635/C026240/C02627 Teflon strip (0.150 m) − 1 E
6 − Corrosion preventive paste
(CM 518)
− a.n.* B
7 − Adhesive
(CM 671)
− a.n.* B
8 − Chemical conversion material
(CM 316)
− a.n.* B
9 − Acetone
(CM 203)
− a.n.* B
10 − Lacquer
(CM 4012)
− a.n.* B
11 − Hardener
(CM 4013)
− a.n.* B
12 − Adhesive
(CM 671)
− a.n.* B, D
*a.n. = as needed
Disposition:
A = The material kit contains no standard parts (DIN, ISO, EN etc.).
If this item is needed, a separate order has to be placed for it.
B = Consumable material, to be ordered from the Interturbine company as needed.
CM item number i.a.w. list of consumable materials in the AMM.
C = Only needed, if bearing is replaced.

### Page 4

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 4 of 14 REVISION 01, 2006-10-18
2006-09-04
D = Only needed, if floor is repaired.
E = New, included in kit.
D. Material Necessary for Each Spare
See Section 2.C.
E. Reidentified Parts
After modification of the rod i.a.w. section 3.H. of this Alert Service Bulletin the part number
of the rod changes from L671M5040205 to L671M5040215 and the part number of the lever
changes from L671M5040101 to L671M5040102.
Accomplish reidentification i.a.w. Section 3.H.(2)(c) of this Alert Service Bulletin.
F. Special Tooling
Not applicable.
3. Accomplishment Instructions
A. Preliminary work steps:
(1) Remove forward access cover i.a.w. AMM, 52-40-00, 4-3.
(2) Remove middle cover i.a.w. AMM, 52-40-00, 4-4.
(3) If installed, remove equipment plate i.a.w. AMM, 25-70-00, 4-2.
B. Inspection of bearing and floor:
CAUTION IF THE LINEAR TRANSDUCER (11, FIGURE 1) IS DETACHED, AVOID
MOVING IT FURTHER THAN ITS NORMAL CONTROL RANGE.
OTHERWISE, THE LINEAR TRANSDUCERS WILL BE DAMAGED.
(1) Remove cotter pin (10, Figure 1), nut (9), washers (8) and bushing (7). Detach linear
transducer (11) with washer (6) downwards.
(2) Check bearing (1, Figure 2) for freedom of movement. If binding, rough or not smooth
turning is detected during turning or tilting of bearing (1), the bearing (1) must be
replaced. Replacement i.a.w. Section 3.C. of this Alert Service Bulletin.
(3) If new signs of chafing i.a.w. Figure 4 are detected on the lower side of the
floor (1, Figure 4), the bearing (4, Figure 3) must be replaced. Replacement of bearing
i.a.w. Section 3.C. of this Alert Service Bulletin.
(4) If the lower side of the floor (1, Figure 4) is damaged in the area of the assembly opening
(with open honeycomb part and/or layer), the bearing (4, Figure 3) must be replaced
and the floor must be repaired.
Replacement of bearing i.a.w. Section 3.C. and repair of floor (1) i.a.w. Section 3.D of
this Alert Service Bulletin.

### Page 5

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 5 of 14
2006-09-04
REVISION 01, 2006-10-18
(5) If there is no binding on the bearing (1, Figure 2) and the floor (1, Figure 4) has no new
signs of chafing i.a.w. Figure 4 and is not damaged in the area of the assembly opening,
proceed i.a.w. Section 3.E. of this Alert Service Bulletin.
C. Replacement of bearing (4, Figure 3):
(1) Remove lockwire from nuts (1, Figure 3).
(2) Remove nuts (1, Figure 3) and detach plate (2) from linear transducer (3). Protect linear
transducers (3) from damage with suitable measures.
(3) Replacement of bearing (4, Figure 3) i.a.w. AMM, 20-00-00, 2-14.
NOTE Nuts (1, Figure 3) will finally be tightened and secured only when the linear
transducers (3) are adjusted.
(4) Put linear transducers (3, Figure 3) through plate (2). Loosely screw nuts (1) onto linear
transducers, so that linear transducers (3) do not slip out of the plate (2).
(5) Adjust linear transducers i.a.w. AMM, 76-10-00, 5-3.
(6) Actuate tail rotor pedals and check tail rotor controls for free and smooth movement.
By doing so, especially check transducer linkage rod (19, Figure 1) and rod (21) for
freedom of movement.
(7) After completion of work, accomplish inspection for foreign matter and objects.
(8) If the floor (1, Figure 4) has no new signs of chafing, proceed i.a.w. Section 3.F of this
Alert Service Bulletin.
D. Repair of floor (1, Figure 4):
NOTE If honeycomb part/layer is damaged within an area of more than 2 cm by
6 cm, contact ECD customer support.
(1) If necessary, carefully remove protruding burr from the area around the edge of the
assembly opening using a file. Remove chips.
(2) Fill up floor honeycomb part (1, Figure 4) with adhesive (CM 671).
E. Affixing of teflon strip (2, Bild 6):
CAUTION WHEN PROCESSING THE ADHESIVE COMPLY WITH THE
MANUFACTURER‘S INSTRUCTIONS.
(1) Using abrasive paper, roughen bonding surface on the lower side of the floor (1, Figure
6), clean with acetone (CM 203) and leave to air.
(2) Using abrasive paper, roughen brown side of teflon strip (2, Figure 6), clean with
acetone (CM 203) and leave to air.

### Page 6

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 6 of 14 REVISION 01, 2006-10-18
2006-09-04
(3) Affix teflon strip (2, Figure 6) i.a.w. figure 6 to the lower side of the floor (1) in parallel
to the floor edge. By doing so, evenly apply adhesive to the brown side of the teflon strip
(2) and to the floor (1). Using a suitable aid, press teflon strip (2) onto the floor (1).
Carefully remove surplus adhesive and allow the bonding to cure i.a.w. the
manufacturer‘s instructions.
(4) Identification of floor:
(a) Using acetone (CM 203), remove grease and dirt from the surface to be marked
in the immediate vicinity of the teflon strip (2, Figure 6) on the lower side of the floor
(1) and leave to air.
(b) Using a permanent marker, identify accomplishment of this Alert Service Bulletin
by marking the Alert Service Bulletin number to the immediate vicinity of the teflon
strip (2, Figure 6).
(c) Protect marking by means of lacquer (CM 4012, CM 4013).
F. Final work steps:
(1) Slide washer (6, Figure 1) and linear transducer (11) onto rod. Attach linear transducer
with bushing (7), washer (8) and nut (9). Tighten nut (9) only until attachment hardware
is free from play. Secure nut (9) with cotter pin (10).
(2) After completion of work, accomplish inspection for foreign matter and objects.
(3) If removed, install equipment plate i.a.w. AMM, 25-70-00, 4-2.
(4) Install middle cover i.a.w. AMM, 52-40-00, 4-4.
(5) Install forward access cover i.a.w. AMM, 52-40-00, 4-3.
G. Confirm accomplishment of Section 3.A up to and including Section 3.F of this Alert Service
Bulletin by an entry in the historical record of the helicopter.
H. Modification of rod (21, Figure 1).
NOTE Accomplish modification of rod by the next periodical inspection at the
latest.
(1) Removal of rod:
(a) Remove cover cap (1, Figure 1) from floor (3) and align rod (21) so that screw (22)
can be removed through the assembly opening in the floor (3). Store cover cap (1)
for reuse.
CAUTION IF THE TRANSDUCER LINKAGE ROD (19) IS DETACHED, AVOID
MOVING ROD (21) FURTHER THAN ITS NORMAL CONTROL
RANGE. OTHERWISE, THE LINEAR TRANSDUCERS LVDT
COLLECTIVE (11) WILL BECOME DAMAGED.

### Page 7

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 7 of 14
2006-09-04
REVISION 01, 2006-10-18
(b) Remove cotter pin (16, Figure 1), nut (15), washers (17, 20) and screw (22).
Disconnect transducer linkage rod (19) from rod (21). Protect transducer linkage
rod (19) from damage with suitable measures.
(c) Remove cotter pin (10, Figure 1), nut (9), washers (6, 8) and bushing (7). Pull rod
(5) out of plate (12).
(d) Remove cotter pin (14, Figure 1), nut (13), washer (4) and screw (2). Remove
rod (21) from floor (3).
(2) Modification and reidentification of rod (1, Figure 5):
CAUTION DURING LOWERING, ENSURE NOT TO LOWER SCREW HEAD
MORE THAN 0.2 MM THAN THE SURFACE OF THE
ROD (1, FIGURE 5) IS.
(a) Using a 100 degree countersink, lower borehole of rod (1, Figure 5) until screw
head of screw (2) is flush with the surface of the rod (1).
(b) Re–establish surface protection using chemical conversion material (CM 316) and
leave to dry i.a.w. the manufacturer‘s instructions.
(c) Reidentification of rod and lever:
1 Using a black permanent marker, cross out old part number L671M5040205
of rod (1, Figure 5) and old part number L671M5040101 of lever  but
leave them still legible.
2 Using a black permanent marker, write new part number L671M5040215 of
rod (1, Figure 5) and new part number L671M5040102 of lever  to the
immediate vicinity of the old part numbers and protect by means of
lacquer (CM 4012, CM 4013).
(3) Installation of rod (21, Figure 1):
(a) Position rod  (5, Figure 1) together with washers (6, 8), bushing (7) and nut (9) in
plate (12). Tighten nut (15) only to such an degree that attachment hardware is free
from play. Secure nut (9) with cotter pin (10).
(b) Apply corrosion preventive paste (CM 518) onto screw (2, Bild 1). Position rod (21)
on floor (3) and attach to floor (3) by means of screw (2), washer (4) and nut (13).
Torque–tighten nut (13) to 1–1.5 Nm and secure with cotter pin (14).
(c) Apply corrosion preventive paste (CM 518) onto screw (22, Figure 1) and align
rod (21) so that screw (22) can be put through the assembly opening in the
floor (3).
(d) Attach transducer linkage rod (19, Figure 1) to rod (21) with screw (22),
washers (17, 20), additional washer (18) and nut (15). Tighten nut (15) only to such
an degree that attachment hardware is free from play. Secure nut (15) with cotter
pin (16).

### Page 8

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 8 of 14 REVISION 01, 2006-10-18
2006-09-04
(e) Close assembly opening in the floor (3, Figure 1) with cover cap (1). By doing so,
insert cover cap (1) from the upper side of the floor.
(f) Actuate tail rotor pedals and check tail rotor controls for free and smooth
movement. By doing so, especially check transducer linkage rod (19, Figure 1) and
rod (21) for freedom of movement.
(4) Confirm accomplishment of Section 3.H. of this Alert Service Bulletin by an entry in the
historical record of the helicopter.
4. Appendix
Not applicable.

### Page 9

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 9 of 14
2006-09-04
REVISION 01, 2006-10-18
Removal/Installation of Rod
Figure 1
1 Cover cap
2 Screw
3 Floor
4 Washer
5 Rod
6 Washer
7 Bushing
8 Washer
9 Nut
10 Cotter pin
11 Linear Transducers
12 Plate
13 Nut
14 Cotter pin
15 Nut
16 Cotter pin
17 Washer
18 Washer LN9025-0615L
19 Transducer linkage rod
20 Washer
21 Rod
22 Screw
1
2
3
4
5
6
7
8
9
1011
12
11
13
14
16
17
19
20
21
22
After modification.
1–1.5 Nm
Assembly opening.
15
18

### Page 10

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 10 of 14 REVISION 01, 2006-10-18
2006-09-04
Inspection of Bearing
Figure 2
1 Bearing
2 Linear Transducers
1
2
2
Inspect bearing for binding, rough or not smooth turning by turning and tilting
bearing.

### Page 11

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 11 of 14
2006-09-04
REVISION 01, 2006-10-18
Replacement of Bearing
Figure 3
1 Nut
2 Plate
3 Linear Transducers
4 Bearing LN9367GE6N2
1
1
3
2
3
4

### Page 12

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 12 of 14 REVISION 01, 2006-10-18
2006-09-04
Lower Side of Floor
Figure 4
1 Floor
2 Rod
3 Transducer linkage rod
Possible chafing.
1
2
3
Assembly opening.
View on lower side of floor.
FLIGHT DIRECTION

### Page 13

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 13 of 14
2006-09-04
REVISION 01, 2006-10-18
Modification of Rod
Figure 5
1 Rod
2 Screw
3 Rod
1
2
2
Using a 100 degree countersink, lower borehole of rod (1) until screw head
of screw (2) is flush with the surface of the rod (1).
Chemical conversion material (CM 316).
Part number of lever (lower side of part).
Part number of rod (1).
1
3
Lever consists of rod (1) and rod (3).
L671M50401XX

### Page 14

ALERT SERVICE BULLETIN
EC135
EC135-67A-012
PAGE 14 of 14 REVISION 01, 2006-10-18
2006-09-04
Modification of Floor
Figure 6
1 Floor
2 Teflon strip
Lower side of floor
1
2
Assembly opening
Affixed with adhesive (CM 671).
All dimensions in mm.
Identify with the number of the Alert Service Bulletin.
ASB EC135-67A-012
FLIGHT DIRECTION

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
