# Airbus Helicopters Alert Service Bulletin EC135-67A-032

Copy: No revision named ("Airbus Helicopters ASB EC135-67A-032 Rev 0"), 21 pages: PDF https://openairdocs.org/files/sha256/33/15/3315adee845fe929ccbc9cdc12e79bcbe83cded6eb81dd7ae842e376fe779a8e; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-67a032/file/3315adee845f.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1173, the docket of AD 2021-07-12. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135-67A-032
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-67a032

## Text (21 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1173, the docket of AD 2021-07-12. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
Valid for Version(s): T1, T2, T2+, T3, P1, P2, P2+, P3
635 T1, 635 12+, 635 13, 635 P2+, 635 P3
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
ROTOR FLIGHT CONTROL - Cyclic stick
Retrofit of cyclic stick weight compensation
For the attention of
Revision No.  Date of issue
Revision 0  2018-02-07
Summary:
With this Alert Service Bulletin (ASB), Airbus Helicopters Deutschland (AHD) prescribes the
retrofit of the weight compensation of the cyclic stick.
Compliance:
Compliance with this Alert Service Bulletin is mandatory.
Revision 0, 2018-02-07  PAGE 1 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
1  PLANNING INFORMATION
1.A  EFFECTIVITY
1.A.1 Helicopters/installed equipment and parts
EC135, T1, T2, T2+, T3, P1, P2, P2+, P3, 635 T1, 635 T2+, 635 T3, 635 P2+, 635 PЗ, all
S/N with installed 3-axis Auto Pilot System up to 1263 inclusive and S/N 1265.
The change will be introduced into serial production with S/N 1266.
Before accomplishment of this ASB  After accomplishment of this ASB
1.A.2 Non-installed equipment and parts
Not applicable.
PAGE 2 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
1.B  ASSOCIATED REQUIREMENTS
None.
1.C  REASON
As a result of reassessment of the flight control system, it has been determined that
a failure that leads to an uncommanded disengagement of the main rotor trim
actuators, during flight with autopilot engaged and hands-off controls, could lead to
high roll and pitch rates, which would require pilot intervention within a reaction
time below that required by the current airworthiness standards. With
accomplishment of this ASB this issue is corrected.
1.D  DESCRIPTION
Open the forward access cover. Install the spring mod. on the longitudinal axis.
Install the friction brake on the lateral axis. Adjust the friction brake. Check for free
movement of the cyclic control. Close the forward access cover.
1.E  COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
Install the cyclic stick weight compensation in accordance with Section 3.B of this
ASB before the helicopter is delivered at the latest.
Non-installed equipment and parts:
Not affected.
1.E.2  Compliance in service
Helicopters/installed equipment and parts:
The retrofit of the cyclic stick weight compensation (see Section 3.B of this ASB) must
be accomplished by 31.10.2018 at the latest.
Non-installed equipment and parts:
Not affected.
1.F  APPROVAL
Approval of modifications:
The information or instructions contained in this document refer to change no. 4845.
The technical content of this document is approved by EASA.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others
Estimated
approx. 8 h
Man-hours
Revision 0, 2018-02-07  PAGE 3 of 21
This document is available on the internet: www.airb  ushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
1.H  WEIGHT AND BALANCE
Weight: 0.204 kg
Arm longitudinal: 2024 mm  Moment longitudinal: 413 kgmm
Arm lateral: 232 mm  Moment lateral: 47 kgmm
POWER CONSUMPTION
Not affected.
1.J  SOFTWARE UPGRADES/UPDATES
Not affected.
1.K  REFERENCES
SPM(MTC) EC135, SRM EC135, AMM EC135/635
1.L  OTHER AFFECTED PUBLICATIONS
Publications to be updated:
The changes to AMM EC135 and IPC EC135 which are required as a result of this ASB
will be incorporated with one of the next revisions.
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
Not affected.
Mixability:
Not affected.
PAGE 4 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
All material kits required will be provided free of cost by AHD only within the time
limits that apply for the compliance (Section 1.E). Material that is ordered outside
the time limits given in the ASB will be charged according to the ruling prices.
2.B  LOGISTIC INFORMATION
Due to the large number of impacted helicopter, availability of parts and the limited
time frame it is necessary to schedule the delivery of kits for the individual
helicopter.
Please fill in and send back the reply form on page 19 of this ASB. The kits will be
send in accordance with this reply.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
Material kit to be ordered for one helicopter:
Material kit SB-135-67A-032-2C i.a.w. design document L670M1004894.
No.  Keyword  Qty  New P/N  Old P/N  Rem.
1  Bracket assy  1  L670M1014101
2  Spring  1  L670M1015201
117-41381-01
Eye bolt  1  or
L671M1021301
4  Washer  2  EN2139-06020
1  EN2139-06010
5  Washer
1  EN2139-06010
1  MBBN3129-06D
6  Nut
1  MBBN3129-06D
1  EN2367-14018
7  Split pin
1  EN2367-14018
ISO4762-M5X14-A2-
Screw  2
70
9  Washer  2  EN3822-050
10  Bolt  1  L671M1030220
11  Cap spring  32  DIN2093B20  B
12  Washer  1  LN65045-16
Revision 0, 2018-02-07  PAGE 5 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
No.  Keyword  Qty  New P/N  Old P/N  Rem.
13  Friction disc  1  L221M0012206
1  MBBN3129-08D
14  Nut
1  MBBN3129-08D
1  LN94-20025
15  Split pin
1  LN94-20025
16  Insert  2  SL10-438M5
17  Bolt  1  L635M1021201
18  Bolt  1  L671M1005256
19  Washer  1  LN29952-0815M
20  Angle  1  L221M1020206  A
21  Spring  1  RZ087DX
DIN65268-05012A
22  Screw  2  or
LN9038-05012
LN9025-0510L
23  Washer  2  or
LN9025-0520L
Remark:
A = Airbus Helicopters Deutschland does not take back parts with old part numbers.
B = The material kit contains more spring caps than the usually necessary number.
PAGE 6 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
Consumables to be ordered separately:
Products can be ordered from KLX Aerospace Solutions. The given CM numbers are
i.a.w. the list of consumable materials of the Standard Practice Manual (MTC).
Website: https://klxaerospace.com
Email: integration@klx.com
WARNING
RESPECT THE SAFETY DATA SHEET OF THE
MANUFACTURER.
No.  Keyword  Qty.  Specification **  Rem.
(approx.)
1  Aceton  a.n.*  203
2  Corrosion preventive  0.5 liter  518
paste
Adhesive  58  EC 1838B-A  601
4  Adhesive paste  1g  6057
*a.n. = as needed
** Specification i.a.w. MTC, 20-01-01-102.
Remark:
A = It is mandatory to use adhesive CM 601. Do not replace it by adhesive CM 671 as
described in the list of consumable materials.
Special tools:
Keyword  Qty.  Specification  Rem.
Spring balance  1  Measurement range up to 50 N
Remark:
A = Commercial product.
2.D  MATERIAL TO BE RETURNED
None.
Revision 0, 2018-02-07  PAGE 7 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
Not applicable.
З.В  WORK STEPS
3.B.1 Preliminary steps
1. De-energize the electrical system of the helicopter, refer to AMM, 24-00-00, 2-1.
2. Remove the forward access cover, refer to AMM, 52-40-00, 4-3.
3.B.2 Procedure
NOTE  It is not necessary to remove the angle (6, Fig. 1) of the control rod
assy (5).
1. Remove the spring (1, Fig. 1) from the control rod assy (5).
2. Remove the spring (1, Fig. 1) from the angle (2) and from the helicopter.
3. Remove the screws (3, Fig. 1), washers (4) and the angle (2) from the helicopter.
Detail E (see Figure 8)
5  2  1
3,4
(6)
1 Spring  RZ087DX
2 Angle  L221M1020206
3 Screw  DIN65268-05012A or
LN9038-05012
4 Washer  LN9025-0510L or
LN9025-0520L
5 Control rod assy  L221M1021101
6 Angle
Removal of angle and spring
Figure 1
PAGE 8 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
4. Install the inserts (1, Fig. 2) into the cockpit floor with adhesive paste (CM 6057),
refer to the measurements given in figure 2 and install in accordance with MTC
20-02-08-406 and SRM 51-20-00, 8-18.
5. Let the adhesive paste (CM 6057) cure, refer to the instructions of the
manufacturer.
Detail A (see Figure 8)  All dimensions in mm
• (11)
Ø 17.4+0.2
× 1889 -
Ø 17.4+0.2 -
1 Insert  SL10-438M5
/1\  Installed with adhesive paste (CM 6057)
Installation of the inserts in the cockpit floor
Figure 2
NOTE  When the connections of the control rods of the cyclic stick are
opened, the cyclic stick can move uncontrollably.
6. Fixate the cyclic stick to prevent it from falling in logitudinal and / or lateral
direction.
Revision 0, 2018-02-07  PAGE 9 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
7. Replace the bolt (4, Fig. 3) with the eye bolt as follows:
a. Remove and discard the split pin (1, Fig. 3) and the nut (2).
b. Remove the washer (3, Fig. 3) and the bolt (4).
c. Install the eye bolt (5, Fig. 3) and the washers (6, 7) wet with corrosion
preventive paste (CM 518).
d. Torque the nut (8, Fig. 3) to a value between 5 Nm and 6 Nm.
e. Install the split pin (9, Fig. 3).
Detail B (see Figure 8)
Removal bolt  Installation eye bolt
5Nm - 6Nm
1 Split pin  EN2367-14018
2 Nut  MBBN3129-06D  Inserted with corrosion
3 Washer  EN2139-06010  preventive paste (CM 518).
4 Bolt  L635M1021201
5 Eye bolt  117-41381-01 or L671M1021301
6 Washer  EN2139-06020
7 Washer  EN2139-06010
8 Nut  MBBN3129-06D
9 Split pin  EN2367-14018
Replacement of the bolt with the eye bolt
Figure 3
PAGE 10 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
f. Make sure that the safety element of the control rod (1, Fig. 4) does not have
the same orientation as the eye bolt (2).
g. If the safety of the control rod (1, Fig. 4) has the same orientation as the eye
bolt (2), turn the safety around.
Detail F (see Figure 8)
Orientation
1 Safety of control rod
2 Eye bolt  117-41381-01 or L671M1021301
Orientation of the safety of the control rod and the eye bolt
Figure 4
Revision 0, 2018-02-07  PAGE 11 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
8. Install the bracket assy (3, Fig. 5) to the cockpit floor as follows:
a. Put the bracket assy (3, Fig. 5) in its installation position on the inserts.
b. Install the bracket assy (3, Fig. 5) with the washers (2) and the screws (1) wet
with corrosion preventive paste (CM 518).
c. Push the bracket assy (3, Fig. 5) as far as possible in flight direction.
d. Torque the screws (1, Fig. 5) to a value between 3 Nm and 4 Nm.
e. Make sure that the lever of the bracket assy (3, Fig. 5) can move freely.
f. If the lever of the bracket assy (3, Fig. 5) is blocked by a screw (1), loosen the
screws (1) and move the bracket assy (3, Fig. 5) until the lever can move
freely. Then torque the screws (1, Fig. 5) to a value between 3 Nm and 4 Nm.
View C (see Figure 8)
FLIGHT DIRECTION
/2
1 /1  3Nm - 4Nm
3Nm - 4Nm
1 Screw  ISO4762-M5X12-A2-70
2 Washer  EN3822-050
3 Bracket assy  L670M1014101
Inserted with corrosion preventive paste (CM 518)
First hole on the bracket assy
Installation of the bracket assy
Figure 5
9. Install the spring between the first hole of the bracket assy and the eye bolt,
refer to figure 8.
10. Replace the bolt (1, Fig. 6) with the bolt (7) as follows:
a. Remove and discard the split pin (6, Fig. 6) and the nut (5).
b. Remove the washer (4, Fig. 6) and the bolt (1).
PAGE 12 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
c. Make sure that the bushings (2, 3, Fig. 6) are still in their installation positions.
d. Make sure that the collar of the bushing (3, Fig. 6) fits against the shaft (13).
e. If the bushings (2, 3, Fig. 6) are too loose, fixate them to prevent them from
talling out.
f. Remove discs from the washer (9, Fig. 6) until the thickness of the washer (9)
is 0.8 mm.
g. Put the washer (9, Fig. 6) in its installation position (centered on the hole) and
bond it with adhesive (CM 601) to the shaft (13). (see photos and illustration
in figure 9)
h. Fixate the washer (9, Fig. 6) to prevent it from moving during the curing time
of the adhesive (CM 601).
i. Put the friction disc (10, Fig. 6) in its installation position (centered on the
hole) and bond it with adhesive (CM 601) to the lever (14). (see photos and
illustration in figure 9)
j. Fixate the friction disc (10, Fig. 6) to prevent it from moving during the curing
time of the adhesive (CM 601).
k. Let the adhesive (CM 601) cure, refer to the instruction of the manufacturer.
NOTE  The number of cap springs (8, Fig. 6) in the material kit is higher
than the usually necessary number of 30 cap springs (8, Fig. 6).
1. Put 30 cap springs (8, Fig. 6) in their installation positions on the close
tolerance bolt (7).
_ CAUTION
DURING INSTALLATION OF THE CLOSE TOLERANCE
BOLT THE BUSHINGS MAY BE MOVED, WHICH WILL
RESULT IN ISSUES IN THE FLIGHT CONTROL. MAKE
SURE THAT THE BUSHINGS ARE IN THEIR
INSTALLATION POSITIONS AFTER INSTALLATION OF
THE CLOSE TOLERANCE BOLT.
m. Install the cap springs (8, Fig. 6) and the close tolerance bolt (7) through the
shaft (13) and the lever (14) with the castellated nut (11).
n. Make sure that the bushings (2, 3, Fig. 6) are still in their installation positions.
(see figure 6)
o. Adjust the lateral friction break, refer to the description in section 3.B.3 in this
ASB.
p. Do the measurement of the breakout forces, refer to the description in
section 3.B.4 in this ASB.
q. Do the check of the free movement of the cyclic stick, refer to the description
in section 3.B.5 in this ASB.
Revision 0, 2018-02-07  PAGE 13 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
Removal bolt (before SB)  View D (see Figure 8)  Installation bolt
3  (more details see figure 9)  (after SB)
6  Section E - E
→ 0.81
/2 10
9/2
3 11
12
13
3
14  8 (×30) /3  7
1 Bolt  L671M1005256  8 Cap spring  DIN2093B20
2 Bushing  L671M1005238  9 Washer  LN65045-16
3 Bushing  L671M1005235  10 Friction disc  L331M0012206
4 Washer  LN29952-0815M  11 Nut  MBBN3129-08D
5 Nut  MBBN3129-08D  12 Split pin  LN94-20025
6 Split pin  LN94-20025  13 Shaft  L671M1013101
7 Bolt  DIN65338K10098T  14 Lever  B671M2012101
Remove discs until specified value is achieved.
Bonded with adhesive (CM 601). Polish bonding surface slightly and clean it with
acetone (CM 203) before bonding. Make sure that washer (9) and the friction disc
(10) are not bonded together and that the friction area is free of adhesive residues.
Tighten the nut (11) until the required breakout force according to the rigging
specification at the upper end of the cyclic stick in both directions (left / right) is
reached. Maximum torque: 6 Nm.
If the split pin cannot be pinned and/or the required force cannot be reached, add or
remove additional cap springs (8).
Replacement of the bolt with the bolt
Figure 6
PAGE 14 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
3.B.3 Adjustment of the lateral friction brake
1. Make sure that the friction brake is fully released for the adjustment procedure.
2. Connect the external pump drive to the hydraulic power system, refer to AMM,
29-00-00, 2-1.
3. Energize the electrical system, refer to AMM, 24-00-00, 2-1.
4. Switch the external pump drive on.
5. Move the cyclic stick at least 10 times through its full motion range for the
lateral axis.
I CAUTION
DAMAGE TO THE FORCED TRIM RELEASE (FTR)
SWITCH ON THE CYCLIC STICK. DO NOT APPLY TO
MUCH FORCE ON THE FTR SWITCH WHEN THE
SWITCH IS PRESSED CONTINUOUSLY BY A SUITABLE
TOOL.
6. Use a suitable tool to continuously press the FTR switch on the cyclic stick.
7. Have a look at the measurement points on the cyclic stick in the figure 7.
NOTE  The breakout forces have to be measured free from play.
8. Move the cyclic stick about 10mm along the axis to be measured.
NOTE  The breakout force is defined as the initial force which is necessary
to move the controls out of their related rest position.
9. Push the cyclic stick in measurement direction and read the force necessary to
start the cyclic stick moving from the spring balance.
10. Repeat the measurement of the breakout force at least three times in both
directions and calculate the average value for each direction.
I CAUTION
DAMAGE TO THE BOLT AND CAP SPRINGS IF THE
MAXIMUM TORQUE IS MORE THAN 6 Nm. DO NOT
TORQUE THE NUT (11, Fig. 6) TO A TORQUE VALUE
OF MORE THAN 6 Nm. IF THE NECESSARY BREAKOUT
FORCE CANNOT BE REACHED ADD OR REMOVE
ADDITIONAL CAP SPRINGS.
11. Torque the nut (11, Fig. 6) and measure the breakout force again, refer to the
steps 7 to 10 in section 3.B.3 in this ASB. The breakout force should increase 1 N
to 1.5 N.
Revision 0, 2018-02-07  PAGE 15 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
12. If the increase of the breakout force is less than 1N, do the step 11 again.
13. Secure the castellated nut (11, Fig. 6) with the split pin (12).
14. Release the FTR switch on the cyclic stick.
15. Switch the external pump drive off.
3.B.4 Measurement of the breakout force of the cyclic stick in lateral direction
NOTE  All force data refer to the helicopter with active hydraulic system
(both systems) and normal operating pressure. Also the
measurement is done against the trim spring force. The switch
Forced Trim Release (FTR) on the cyclic stick is not pressed. The
cyclic stick is in the "neutral" position.
1. If not already connected, connect the external pump drive to the hydraulic
power system, refer to AMM, 29-00-00, 1-1.
2. Switch the external pump drive on.
NOTE  The breakout forces have to be measured free from play.
3. Move the cyclic stick about 10mm along the axis to be measured.
4. The measurement points on the cyclic stick can be seen in the figure 7.
NOTE  The breakout force is defined as the initial force which is necessary
to move the controls out of their related rest position.
5. Push the cyclic stick in measurement direction and read the force necessary to
start the cyclic stick moving from the spring balance.
6. Repeat the measurement of the breakout force at least three times in both
directions and calculate the average value.
7. Make sure that the breakout force is between 6 N and 11 N.
8. Push the cyclic stick approximately 90 mm from the center position with the
spring balance and read the maximum control force from the spring balance in
both directions.
9. Make sure that the maximum control force is less than 30 N.
10. Switch the external pump drive off.
PAGE 16 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
Grip reference point cyclic grip lateral direction
Figure 7
3.B.5 Final steps
1. Check freedom of movement of the cyclic stick as described within the following
procedure:
a. Make sure that all tools and equipment were removed below the cockpit
floor.
b. Switch the external pump drive on.
c. Slowly move the cyclic stick through the complete control range.
d. Meanwhile check the freedom of movement in all positions.
e. Make sure that the primary end stops in the main rotor actuator can be
reached, which means that the main piston of the actuator does not move
anymore, while the input lever is still able to move.
f. Switch the external pump drive off.
2. Disconnect the external pump drive from the hydraulic power system, refer to
AMM, 29-00-00,2-1.
3. Close the forwad access cover, refer to AMM, 52-40-00, 4-3.
Revision 0, 2018-02-07  PAGE 17 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
З.С  COMPLIANCE CONFIRMATION
Compliance with this document:
Confirm accomplishment of this ASB by an entry in the historical record of the
helicopter.
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
After accomplishment of the measures given in this ASB, the pilots must be informed
on its content.
Maintenance instructions:
Not applicable.
4  APPENDIX
Reply form sheet.
PAGE 18 of 21  Revision 0, 2018-02-07
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB EC135-67A-032
Reply form sheet
Reply form sheet for ASB EC135-67A-032 Retrofit of cyclic stick weight compensation.
Please fill in the reply form sheet and send it to the given e-mail.
For optimized, internal allocation please add operator's name and the related ASB
number in the email subject line.
Please note that the receipt of this reply form sheet does NOT trigger the delivery of the
parts. We thus ask all direct customers of Airbus Helicopters to also send their order
with this reply sheet. All other Airbus Helicopters customers send their orders to their
usual Airbus Helicopters subsidiary.
To
Airbus Helicopters Deutschland GmbH
Customer Support
e-mail: contact.replysheet-servicebulletin.ahd@airbus.com
Address of operator:
Helicopter S/N  installation date  Estimated  Helicopter S/N  installation date  Estimated  Helicopter S/N  installation date  Estimated
Date:  Signature:
Please copy page! Original page remains in Alert Service Bulletin!
Revision 0, 2018-02-07  PAGE 19 of 21
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 20

ASB EC135‐67A‐032
PAGE 20 of 21Revision 0, 2018‐02‐07
General view of views and sections
Figure 8
1V i e w AF i g u r e 2
2V i e w BF i g u r e 3
3V i e w CF i g u r e 5
4V i e w DF i g u r e 6
5V i e w E F i g u r e 1
6V i e w F F i g u r e 4
View from bottom sideBefore ASB After ASB
A
B B
C
D D
E
F

### Page 21

ASB EC135‐67A‐032
PAGE 21 of 21Revision 0, 2018‐02‐07
Photos of the installation of the friction disc and the washer on the shaft assy and the lever
Figure 9
Remove discs until specified value is achieved.
Bonded with adhesive (CM 671). Polish bonding
surface slightly and clean it with acetone (CM 203)
before bonding. Make sure that washer (9) and the
friction disc (10) are not bonded together and that
the friction area is free of adhesive residues.
Tighten the castellated nut (11) until the required
breakout force according to the rigging
specification at the upper end of the cyclic stick in
both directions (left / right) is reached. Maximum
torque: 6 Nm.
If the split pin cannot be pinned and/or the
required force cannot be reached, add or remove
additional cap springs (8).
12 11 2 13
9 3 8 (x30) 714
10
0.8
7 Bolt DIN65338K10098T
8 Cap spring DIN2093B20
9 Washer LN65045‐16
10 Friction disc L331M0012206
11 Nut MBBN3129‐08D
12 Split pin LN94‐20025
13 Shaft L671M1013101
14 Lever B671M2012101
10
14
9
13
2
3
3 139
2 Bushing L671M1005238
3 Bushing L671M1005235

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
