# Eurocopter Emergency Alert Service Bulletin EC135-85A-036

Copy: Revision 2 ("Eurocopter ASB EC135-EC635-85-036 Rev 2"), 17 pages: PDF https://openairdocs.org/files/sha256/fc/f6/fcf679ba417e1e0b62f5ad3efd9acfd161cfba51778b0bc8a4a4b73d22fbb5e9; text https://openairdocs.org/service-documents/airbus-helicopters/ec135-85a036/file/fcf679ba417e.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0340; AD 2013-21-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: EC135-85A-036
- Latest revision known: EC135-85A-036, Revision 2, dated June 23, 2010 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135-85a036

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-21-06](https://openairdocs.org/ad/2013-21-06.md), effective Jan 31, 2014: Revision 2

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec135-85a036/proposed.md).

## Text (17 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0340; AD 2013-21-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

EMERGENCY
ALERT SERVICE BULLETIN
EC135
EC135-85A-036
SEITE 1 of 5
2009-04-16
REVISION 2, 2010-06-23
Optional Equipment  –  External Mounted Hoist System  –  Inspection of
the hoist boom for cracks
1. Planning Information
A. Effectivity
(1) Helicopters affected: EC135/EC635, all models with optional equipment 
external mounted hoist system.
(2) Components affected: Hoist boom 44307-500 * or
44307-500-1* or
44301-500*
*) For S/N of the affected hoist booms see Service Bulletin 44307-500-03, Rev. 2
of the Goodrich company.
(3) Spare Parts affected: Hoist boom 44307-500 * or
44307-500-1* or
44301-500*
*) For S/N of the affected hoist booms see Service Bulletin 44307-500-03, Rev. 2
of the Goodrich company.
B. Concurrent Requirements
Not applicable.
C. Reason
During a preflight check of the external mounted hoist system cracks had been detected on
the hoist boom. Therefore, this Emergency Alert Service Bulletin specifies a visual check of
the hoist boom.
With Revison 2 of this Emergency Alert Service Bulletin ECD distributes Service Bulletin
44307-500-03, Rev. 2 of the Goodrich company. This Service Bulletin specifies an
inspection. If no cracks are detected the hoist boom can be operated without limitations after
the accomplishment i.a.w. the Goodrich Service Bulletin 44307-500-03, Rev. 2.
D. Description
EFFECTIVITY Before accomplishment of Service Bulletin 44307-500-03, Rev. 2 of the
Goodrich company.
(1) Check hoist boom for cracks.
EFFECTIVITY With Revision 2 of this Emergency Alert Service Bulletin the Service
Bulletin 44307-500-03, Rev. 2 of the Goodrich company is distributed.
(2) See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company attached to this
Emergency Alert Service Bulletin.

### Page 2

EMERGENCY
ALERT SERVICE BULLETIN
EC135
EC135-85A-036
SEITE 2 of 5 REVISION 2, 2010-06-23
2009-04-16
E. Compliance
EFFECTIVITY Before accomplishment of Service Bulletin 44307-500-03, Rev. 2 of the
Goodrich company.
(1) The check of the hoist boom i.a.w. Section 3.A of this Emergency Alert Service Bulletin
must be accomplished before every first flight of the day.
(2) Stored hoist booms must be checked i.a.w. Section 3.A of this Emergency Alert Service
Bulletin, but not later than before their installation.
(3) If cracks are detected on the hoist boom during a visual check the hoist boom must be
removed or replaced before the next flight.
EFFECTIVITY With Revision 2 of this Emergency Alert Service Bulletin an inspection
i.a.w. Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company is
specified.
(4) The inspection of the hoist boom i.a.w. Service Bulletin 44307-500-03, Rev. 2 of the
Goodrich company must be accomplished within 30 days after receipt of Revision 2 of
this Emergency Alert Service Bulletin.
After that, all measures of this Emergency Alert Service Bulletin are no longer
applicable.
F. Approval
The technical content of this document is approved under the authority of
DOA No. EASA.21J.034.
G. Manpower
EFFECTIVITY Before Revision 2 of this Emergency Alert Service Bulletin.
(1) Approx. 15 minutes for the visual check of the hoist boom.
EFFECTIVITY With Revison 2 of this Emergency Alert Service Bulletin.
(2) See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
H. Weight and Balance
Not applicable.
I. Electrical Load Data
Not applicable.
J. Software Accomplishment Summary
Not applicable.

### Page 3

EMERGENCY
ALERT SERVICE BULLETIN
EC135
EC135-85A-036
SEITE 3 of 5
2009-04-16
REVISION 2, 2010-06-23
K. References
See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
L. Other publications affected
Not applicable.
M. Interchangeability of Parts
Not applicable.
2. Material Information
A. Material – Price and Availability
See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
B. Support Information
Not applicable.
C. Material Necessary for Each Helicopter
See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
D. Reidentified Parts
See Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
E. Special Tooling
Not applicable.

### Page 4

EMERGENCY
ALERT SERVICE BULLETIN
EC135
EC135-85A-036
SEITE 4 of 5 REVISION 2, 2010-06-23
2009-04-16
3. Accomplishment instructions
EFFECTIVITY Before accomplishment of Service Bulletin 44307-500-03, Rev. 2 of the
Goodrich company.
A. Accomplish a visual check of the hoist boom:
NOTE Effective for the installation of the external mounted hoist boom on the LH
and on the RH side.
NOTE The visual check can be accomplished either by the maintenance
personnel or the aircrew.
(1) Clean hoist boom (1, Figure 1) in the marked area and check for cracks. If necessary,
use a flashlight and a mirror.
(2) If cracks are detected during the visual check, contact ECD customer support. In this
case the hoist boom must be removed or replaced before the next flight.
B. Confirm accomplishment of this Emergency Alert Service Bulletin by an entry in the log card
of the external mounted hoist system.
EFFECTIVITY With Revision 2 of this Emergency Alert Service Bulletin an inspection is
specified i.a.w. Service Bulletin 44307-500-03, Rev. 2 of the Goodrich
company.
C. Accomplish Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.
D. Confirm accomplishment of Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company
by an entry in the log card of the external mounted hoist.
4. Appendix
Service Bulletin 44307-500-03, Rev. 2 of the Goodrich company.

### Page 5

EMERGENCY
ALERT SERVICE BULLETIN
EC135
EC135-85A-036
SEITE 5 of 5
2009-04-16
REVISION 2, 2010-06-23
Visual check of the Hoist Boom
Figure 1
1 Hoist boom
1
2
2
2
Check for cracks.
Hoist boom with cracks.
Only LH external mounted hoist
shown.

### Page 6

(No text on this page.)

### Page 7

44307-500-03 Apr 30/10
Highlights-1
SENSORS AND INTEGRATED SYSTEMS (HOIST AND WINCH)
1550 S. VALLEY VISTA DR, DIAMOND BAR, CALIFORNIA 91765
TO: HOLDERS OF SERVICE BULLETIN 44307-500-3,Rev.1, DATED APR 21/10 COVERING THE 
BOOM ASSEMBLY , PART NUMBER 44307-500.
REVISION NO. 2, DATED APR 30/10
HIGHLIGHTS
Pages which have been revised are outlines below together with the highlights of the revision. Please 
destroy your obsolete pages of this manual and replace it with Revision No. 2, DATED APR 30/10.
   
PAGE NO. DESCRIPTION OF CHANGE EFFECTIVITY
2 Revise the compliance time to read  "within 30 days 
after receipt of this service bulletin".
All
COMMERCE DEPARTMENT "These commodities, technology or 
software were exported from the United States in accordance with the Export 
Administration Regulations. Diversion contrary to U.S. law prohibited."

### Page 8

44307-500-03
Page 1 of 10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - One Time Inspection
Feb 15/10
1. Planning Information
A. Effectivity
This Service Bulletin is applicable to the Boom and Support Assembly, part numbers 
44301-500 and 44307-500. The affected boom and support assemblies are listed in Table 
1. The Boom and Support Assemblies are manufactured by Goodrich Corporation, Sensors 
and Integrated Systems, Diamond Bar, California. 
B. Reason
 During a routine inspection conducted in the field. Four boom and support assemblies 
were found to have cracks on the boom elbow, part number 44307-512 (Figure 1), Testing 
and failure analysis were conducted to identify the cause of the crack. 
The root cause of cracking was found to be due to a customer maintenance error.
A one time visual inspection of the boom and support assembly is performed to ensure no 
cracks exist in other boom and support assemblies. If cracks are found, the boom and 
support assembly is removed from service and return to Goodrich for repair or 
replacement.Refer to paragraph 2.F for current price and RMA number. 
COMMERCE DEPARTMENT "These commodities, technology or software were exported from the United States in 
accordance with the Export Administration Regulations. Diversion contrary to U.S. law prohibited."
C. Description
This service bulletin provides the instructions necessary to perform the one time visual 
inspection and corrective action of the boom and support assembly elbow. The one time 
visual inspection consists of visually inspecting the boom and support assembly elbow. If 
crack (s) are found during the inspection, the boom and support assembly must be 
removed from the helicopter. If no cracks are found, the boom and support assembly may 
Table 1: Affected Boom and Support Serial Numbers
GOODRICH 
PART NUMBER
GOODRICH
SERIAL NUMBER
GOODRICH 
PART NUMBER
GOODIRCH 
SERIAL NUMBER
44301-500 0002 thru 033 44307-500 0002 thru 0186
44307-500 0188 thru 0192
44307-500 0194 thru 0198
44307-500 0200 thru 0203
44307-500 0205 thru 0213

### Page 9

44307-500-03
Page 2 of 10
Feb 15/10
Revision 2-Apr 30/10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - 
One Time Inspection and Corrective Action
remain in service and performance of the repetitive inspection i.a.w Eurocopter Germany 
MBB BK117 C-2-85A-024 or EC135-85A-036 is no longer necessary.
D.  Compliance
This mandatory one time inspection must be performed within the next 30 days after receipt 
of this Service Bulletin Compliance is mandatory as defined within the Eurocopter 
Deutschland Service Bulletin.
E. Approval
This service bulletin contains no modification information that revises the approved 
configuration. This modification is in compliance with the existing FAA approved 
configuration. Certification of this Service Bulletin will be with Eurocopter Germany Service 
Bulletin.
F. Manpower
(1) The estimated amount of labor to accomplish the instructions of this Service Bulletin 
for one Boom and Support Assembly is 60 minutes, as follows:
(2) The one time visual Inspection described in  this Service Bulletin shall be performed 
by Hoist Operators/Users, Goodrich Corporation, Sensors and Integrated Systems, or 
by personnel and facilities officially authorized by Goodrich Corporation, Sensors and 
Integrated Systems to perform this one time visual inspection.
G. Material — Cost and Availability
(1)  Material required to accomplish the instructions of this Service Bulletin for each 
Boom and Support Assembly is located in Table 2.
Remove hoist and boom 
assembly
15 minutes
Inspection 10 minutes
Corrective action 20 minutes
Install hoist and boom 
assembly
15 minutes

### Page 10

44307-500-03
Page 3 of 10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - One Time Inspection
Feb 15/10
NOTE: *Corrosion Inhibitive compound, part number 148927 (PPG/PRC Desoto 
International, part number CA 1000, 2820 W. Empire Av. Burbank, CA 91504) may 
be used as an alternate.
NOTE: **Equivalent items can be use.
H. Tooling - Price and Availability
None.
I. Weight and Balance
Not affected.
J. Electrical Load Data
Not affected.
K. Software Accomplishment Summary
Table 2.  Materials Required
NEW P/N DESCRIPTION OLD P/N QTY
*148931 Joint Compound (Mastinox, 6856K 
MIL-P-8116B)
----- AR
148851  Polyurethane 
Paint, Fed-Std. 595 Mil-C-85285-Type 
I,II or III, 
Class H-Lusterless Black-
Color No. 37038
----- AR
146028 Wash Primer, Mil-C-8514 ----- AR
146030  Epoxy Primer, MIL-P-23377 ----- AR
----- Alodine, MIL-C-5541, Class 1A, ----- AR
SBL 44307-500-03 Service Bulletin label ----- 1
** PR1440 or PR1422 Sealant ----- AR
**SK-416 Dye Penetrant Kit
Magnaflux/ITW
----- 1

### Page 11

44307-500-03
Page 4 of 10
Feb 15/10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - 
One Time Inspection and Corrective Action
None.
L. Reference
Goodrich Corporation Component Maintenance Manual 25-00-21-1
M. Other Publications Affected
None.
2. Accomplishment Instructions
A. Prepare for inspection
NOTE: Refer to the rescue hoist Component Maintenance Manual (CMM) 25-00-21-
1 for detail removal instructions. Refer to ECD LOAP document for current 
revision level.
(1) Set the rescue hoist power source OFF. Disconnect and remove the external 
electrical power source from the helicopter.
(2) Remove the rescue hoist from the boom  and support assembly in accordance with 
the instructions in the appropriate CMM.
(3) Remove the boom and support from the helicopter in accordance with the instructions 
in the appropriate CMM.
NOTE: Penetranting oil may be required to remove the boom tube from the elbow.
(4) Remove the boom tube assembly from the elbow assembly in accordance with the 
instructions in the appropriate CMM.
(5) Clean the external and internal surface of the elbow where the crack or crack (s) are 
suspected (refer to Figure 1). 
(6) Remove minor corrosion in accordance with the instructions in the appropriate CMM.
B. Inspection

### Page 12

44307-500-03
Page 5 of 10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - One Time Inspection
Feb 15/10
NOTE: Crack or crack (s) are not allowed on any surface of the boom and support 
assembly. The unserviceable boom and support assembly must be removed 
from the helicopter.
NOTE: Conduct all checks under a strong light and 5x-power to 10x-power 
magnification to detect surface flaws. 
(1) Visually inspect the internal and external  surfaces of the of the boom and support 
elbow for cracks (Refer to Figure 1). If necessary, Perform dye penetrant inspection to 
confirm the suspected crack or crack (s). (refer to Step D). 
(2) If the suspected crack or crack(s) are co nfirmed. Do not install the unserviceable 
boom and support assembly onto the helicopter. Send the unserviceable boom and 
support assembly to Goodrich repair center for replacement of the failed components. 
(3) If no cracks are found return the boom and support assembly to service after 
performing step C.(1) below.
C. Final Assembly
NOTE: Refer to the rescue hoist Component Maintenance Manual (CMM) 25-00-21-
1 for detail installation instructions.
(1) To mitigate the risk of damage to the boom and support assembly with no crack or 
crack(s) due to intrusion of corrosive elements perform the following steps:
(a) Apply a uniform thin film of joint compound on the entire mating surfaces of the 
elbow and boom tube.
(b) Install the boom tube into the elbow and rotate to ensure uniform distribution of 
the joint compound. Wipe off excess material from the boom tube and elbow.
(c) Install the mounting hardware. Torque the mounting hardware nuts to 8 to 12 in-
lbs (.9 N•m to 1.2 N•m). beyond running torque of the lock nut.
(d) Seal around the outside of the boom tube at the outboard face of the boom 
elbow using PR1440 or PR1422. Equivalent items can be used. See Figure 1.
(2) Install the boom and support on the helicopter  in accordance with the instructions in 
the appropriate CMM.
(3) Install the rescue hoist on the boom and support assembly in accordance with the 
instructions in the appropriate CMM.
D. Dye Penetrant Inspection (DPI)

### Page 13

44307-500-03
Page 6 of 10
Feb 15/10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - 
One Time Inspection and Corrective Action
WARNING: DYE PENETRANT IS COMBUSTIBLE AND MODERATELY TOXIC TO SKIN, 
EYES, AND RESPIRATORY TRACT. PROTECTION: CHEMICAL SPLASH 
PROOF GOGGLES, GLOVES, AND FORCED VENTILATION OR 
RESPIRATOR; KEEP CONTAINER CLOSED; KEEP SPARKS, FLAMES, AND 
HEAT AWAY. KEEP PENETRANT OFF SKIN, EYES, AND CLOTHES; DO NOT 
BREATHE VAPORS.
NOTE: The dye penetrant procedures contained in the dye penetrant kit supersedes the 
generic steps below.
(1) Clean the area to be inspected as follows
(a) Clean the test surface to remove any di rt, paint, oil, grease or any loose scale 
that could either keep penetrant out of a defect, or cause irrelevant or false 
indications. 
NOTE:  Smaller flaws will require a longer penetration time
(2) Apply penetrant to the test surface. Allo w approximately 10 to 30 minutes for the 
penetrant to soak into any flaws.
(3) Remove excess penetrant from the surface
(4) Apply the developer to the surface.
(5) Inspect the test area within 10 minutes after the developer is applied.
(6) Clean the test area.
E. Paint and Protect Surface (Repair)
(1) Protect the surface Inspected as follows:

### Page 14

44307-500-03
Page 7 of 10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - One Time Inspection
Feb 15/10
(a) If the painted surface requires repair polish the area with aluminum oxide cloth, 
A-A-1048, or crocus cloth, A-A-1206, as applicable.
W ARNING: CHEMICAL FILM (ALODINE), MIL-C-5541, IS TOXIC TO SKIN, EYES AND 
RESPIRATORY TRACT. AVOID SKIN AND EYE CONTACT. GOOD GENERAL 
VENTILATION IS NORMALLY ADEQUATE.
(b) Apply a protective chemical film, Alodine, MIL-C-5541, Class 1A, to exposed 
aluminum repair areas.
(c) Prepare the exposed metal surface area by masking off the area to be painted
(d) Paint the exposed surfaces as follows:.
1 Apply one coat of primer coat, MIL-C-8514.
2 Apply one coat of primer coat, MIL-P-23377, Type I, CL C
3 Apply one coat of polyurethane, top coat. Refer to Table for paint color.
(e) Remove the masking material after painting.
            Marking
(1) The incorporation of this one time ins pection and Corrective Action service bulletin is 
to be documented on the hoist maintenance records or log-card. 
(2) Upon successful completion of functio nal check enter the date the modification was 
completed on the label’s “DATE” field with black ink.
(3) Attach Service Bulletin Label SBL 44307-500-03 on the boom and support assembly.
F. Point of Contact
To notify Goodrich of the one time inspection finding. Please contact one of the Goodrich 
Representatives at the address listed below:

### Page 15

44307-500-03
Page 8 of 10
Feb 15/10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - 
One Time Inspection and Corrective Action
Goodrich Corporation,
Sensors and Integrated Systems (SIS)
Diamond Bar, California
Attn: Joe Rumolo
Phone: 909-569-0231
FAX: 909-569-0387
For RMA Number:
Danna O’Donnell
Phone: 909-569-0240
FAX: 909-569-0387

### Page 16

44307-500-03
Page 9 of 10
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly - One Time Inspection
Feb 15/10
3. Material Information
Table 3:    Material Information                    
NOTE:        * Corrosion Inhibitive compound, part number 148927 (PPG/PRC Desoto 
International,part number CA 1000, 2820 W. Empire Ave. Burbank, CA 91504) 
may be used as an alternate.
NOTE: ** Equivalent items can be use.
***NOTE: Order Service Bulletin Kit SBK 44307-500-03
NEW P/N QTY
UNIT 
PRICE DESCRIPTION OLD P/N
INSTRUCTIONS/ 
DISPOSITION 
*148931 AR ----- Joint Co mpound (Mastinox, 
6856K 
MIL-P-8116B)
----- Install on the 
entire mating sur-
face of the elbow 
and tube.
148851 AR -----  Polyurethane 
Paint, Fed-Std. 595 Mil-C-
85285-Type I,II or III, 
Class H-Lusterless Black-
Color No. 37038
----- Apply one coat of 
paint.
146028 AR ----- Wash Primer, Mil-C- 8514 ----- Apply one coat of 
wash primer.
146030 AR -----  Epoxy Primer, MIL-P-
23377
----- Apply one coat of 
epoxy primer
----- AR ----- Alodine, 
MIL-C-5541, Class 1A, 
----- Apply Alodine, 
MIL-C-5541, 
Class 1A, to
exposed 
aluminum repair
areas.
**SK-416 1 ----- Dye Penetrant Kit
Magnaflux/ITW
----- Use to perform 
Penetrant test if 
crack or crack (s) 
are suspected.
** PR1440 or PR 
1422
AR ----- Sealant ----- Apply to seal the 
boom gap.
***SBL 44307-
500-03
1 ----- Service Bulletin label ----- Install on boom  
support assembly

### Page 17 (OCR)

GOODRICH
SERVICE BULLETIN
Equipment/Furnishings - Boom and Support Assembly -
One Time Inspection and Corrective Action
Apply sealant to joint after
assembly
Adapter
PN 44301-511
Boom Elbow
PN 44301-512
PN 44307-512
Boom Tube
PN 44307-513
Stress crack generally
found in this location
MOUNTED
HARDWARE
NOTE: The support assembly omitted for clarity
Figure 1. Boom and Support Assembly
Feb 15/10  44307-500-03
Revision1- Apr 21/10  Page 10 of 10

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
