# Airbus Helicopters Alert Service Bulletin EC135H-00A-002

Copy: No revision named ("Airbus Helicopters ASB EC135H‐00A‐002 Rev 0"), 14 pages: PDF https://openairdocs.org/files/sha256/bc/d7/bcd77741780af98645287faf3fc6de55597a44f6c422cd222e33df28da842733; text https://openairdocs.org/service-documents/airbus-helicopters/ec135h-00a002/file/bcd77741780a.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0919, the docket of AD 2020-22-04. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC135H-00A-002
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec135h-00a002

## Text (14 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0919, the docket of AD 2020-22-04. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
Valid for Version(s): T3H, PЗH, 635 T3H, 635 PЗН
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
AIR VEHICLE GENERAL - General information
Inspection of additional Titanium Bolts
For the attention of
Revision No.  Date of issue
Revision O  2020-05-04
Summary:
With this Alert Service Bulletin (ASB), Airbus Helicopters prescribes a one-time inspection of
Titanium Bolts (Ti-Bolts).
Compliance:
Compliance with PART I of this ASB is mandatory (expected as part of EASA AD).
Compliance with PART II of this ASB is essential (not expected as part of EASA AD).
ASB EC135H-00A-002
Revision 0, 2020-05-04  PAGE 1 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
PLANNING INFORMATION
1.A  EFFECTIVITY
1.A.1 Helicopters/ installed equipment and parts
a) EC135, 13Н, РЗН, 635 T3H, 635 P, all S/N up to S/N 2122 inclusive, except
S/N 2121.
b) Ti-Bolts with manufacturer monogram "D":  EN3308H060028F
L535M3001201
1.A.2 Non-installed equipment and parts
See Section 1.A.1. b.
1.B  ASSOCIATED REQUIREMENTS
None.
1.C  REASON
Some Ti-Bolts have been manufactured according to an improper heat treatment
process. This improper process can lead to hydrogen embrittlement of the parts far
above standard limits. Therefore, Airbus Helicopters has issued ASB EC135H-00A-001
to replace the affected Ti-Bolts.
However, Airbus Helicopters was informed by the supplier DECOMATIC, that
additional Ti-Bolts have been manufactured according to this improper heat
treatment process. Affected Ti-Bolts must be identified by an inspection and Ti-Bolts
with the manufacturer monogram "D" must be replaced in accordance with this ASB.
For additional information, see SIN 3365-S-00 and TIL H135-048-2019.
1.D  DESCRIPTION
Inspect the Ti-Bolts. Replace the Ti-Bolts if required.
1.E COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
The inspection and replacement (if required) of the Ti-Bolts must be accomplished in
accordance with Section 3.B of this ASB before delivery of the helicopter.
Non-installed equipment and parts:
Ti-Bolts with manufacturer monogram "D" must neither be installed nor delivered.
PAGE 2 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
1.E.2 Compliance in service
Helicopters/installed equipment and parts:
PARTI
The inspection and replacement (if required) of the Ti-Bolts must be accomplished in
accordance with Section 3.B.2 thru Section 3.B.3 of this ASB within the next 50 Fh
after receipt of this ASB but by 16 July, 2020 at the latest.
PART II
The inspection and replacement (if required) of the Ti-Bolts must be accomplished in
accordance with Section 3.B.5 of this ASB before 31 May, 2021 at the latest.
Non-installed equipment and parts:
Ti-Bolts with manufacturer monogram "D" must not be installed.
1.F  APPROVAL
Approval of this document:
The technical content of this document is approved under the authority of
DOA No. EASA.21J.700.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others
approx. 1.5 h
(inspection)
Estimated
Man-hours  approx. 4 h
(replacement,
if required)
1.H  WEIGHT AND BALANCE
No effect on weight and balance.
POWER CONSUMPTION
Not affected.
1.J  SOFTWARE UPGRADES/UPDATES
Not changed.
1.K  REFERENCES
AMM EC135, AMM EC135/635.
1.L  OTHER AFFECTED PUBLICATIONS
Not affected.
Revision 0, 2020-05-04  PAGE 3 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
After accomplishment of this ASB, the Ti-Bolts with the manufacturer monogram "D"
must not be installed anymore.
Mixability:
Not affected.
PAGE 4 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
None.
2.B  LOGISTIC INFORMATION
None.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
Material supplied by the operator:
The following parts could be affected by a replacement. Affected parts can be
ordered by Airbus Helicopters Spares Order Administration.
Please reference the following number in the customer order: ASB-EC135H-00A-002
PARTI
No.  Keyword  Qty  New P/N  Old P/N  Rem.
L535M3001201
1  Ti-Bolt  24
L535M3001201  B, C
PART II
No.  Keyword  Qty  New P/N  Old P/N  Rem.
EN3308H060028F
Ti-Bolt  2
EN3308H060028F  B, C
Remark:
A = Without manufacturer monogram "D".
B = With manufacturer monogram "D".
C = Airbus Helicopters does not take back parts with old part numbers.
Revision 0, 2020-05-04  PAGE 5 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
Consumables to be ordered separately:
WARNING
RESPECT THE SAFETY DATA SHEET OF THE
MANUFACTURER.
Qty.
NO.  Keyword  Specification **  CM  Rem.
(approx.)
1  Cleaning agent  a.n.*  203  A, B
2  Cleaning agent  a.n.*  217  A, B
*a.n. = as needed
** For specification, refer to AMM 01-00-00, 2-1.
Remark:
A = If required.
B = Cleaning agent (CM 203) or cleaning agent (CM 217) can be used.
The consumables can be ordered separately from the following companies.
Aviatec global aviation  BDSI
Website: https://www.aviatec.net  Website: https://www.boeingdistribution.com
Telephone: +33 1.34.46.45.24 or  Telephone: +1.305.925.2600
+49 4193.8803.630  Fax: +1.305.507.7191
Fax:  +33 1.34.46.45.26 or  AOG: +1.305.471.8888
+49 4193.8803.699  AOG email: AOGdesk@boeingdistribution.com
AOG:  +49 4193.8803.660
AOG email: aog@aviatec.aero
Gaches chimie
Website: https://www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
2.D  MATERIAL TO BE RETURNED
None.
PAGE 6 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
WARNING
DO NOT INSTALL TI-BOLTS WITH MANUFACTURER
MONOGRAM D".
NOTE  Ti-Bolts with manufacturer monogram "D" should be replaced one
by one.
NOTE  The manufacturer monogram may not appear exactly as shown in
the figures. If confirmation is needed contact your Airbus
Helicopters customer support.
З.В  WORK STEPS
З.В.1  Preliminary steps
PART I and PART II
1. Remove the tail rotor drive shaft fairing (AMM 53-50-01, 4-1).
PARTI
2. Remove LH and RH transmission fairing (AMM 71-11-00, 4-4).
3. Remove LH and RH engine cowling (AMM 71-11-00, 4-1).
4. Remove center engine cowling (AMM 71-11-00, 4-2).
5. Remove aft LH and RH engine cowlings (AMM 71-11-00, 4-3).
6. Remove air deflector (AMM 71-32-00, 4-2).
7. Remove the service cover on the rear structure (AMM 52-40-00, 4-6).
Revision 0, 2020-05-04  PAGE 7 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
PARTI
3.B.2  Inspection of the forward drive shaft
1. Inspect the manufacturer monogram (10, Fig. 1) marked on the head of each
I-Bolt (1):
a. If the manufacturer monogram (10, Fig. 1) can be identified and is clearly not
"D", proceed in accordance with Section 3.B.2.3.
b. If the manufacturer monogram (10, Fig. 1) is "D", replace the Ti-Bolt (1) in
accordance with Section 3.B.2.2.
c. If the manufacturer monogram (10, Fig. 1) cannot be identified due to paint
covering, remove the paint that covers the manufacturer monogram (10)
from the head of the Ti-Bolt (1) in accordance with Section 3.B.4.
d. If the manufacturer monogram (10, Fig. 1) cannot be identified, replace the
Ti-Bolt (1) in accordance with Section 3.B.2.2.
2. Replacement of the Ti-Bolt (1, Fig. 1):
a. Remove the Ti-Bolt (1, Fig. 1) (AMM 65-11-00, 4-1).
b. Discard the Ti-Bolt (1, Fig. 1).
c. Install a Ti-Bolt (1, Fig. 1) with an identifiable manufacturer monogram that is
clearly not "D" (AMM 65-11-00, 4-1).
3. Inspect the manufacturer monogram (10, Fig. 1) marked on the head of each
Ti-Bolt (6):
a. If the manufacturer monogram (10, Fig. 1) can be identified and is clearly not
"D", proceed in accordance with Section 3.B.3.
b. If the manufacturer monogram (10, Fig. 1) is "D", replace the Ti-Bolt (6) in
accordance with Section 3.B.2.4.
c. If the manufacturer monogram (10, Fig. 1) cannot be identified due to paint
covering, remove the paint that covers the manufacturer monogram (10)
from the head of the Ti-Bolt (6) in accordance with Section 3.B.4.
d. If the manufacturer monogram (10, Fig. 1) cannot be identified, replace the
Ti-Bolt (6) in accordance with Section 3.B.2.4.
4. Replacement of the Ti-Bolt (6, Fig. 1):
a. Remove the Ti-Bolt (6, Fig. 1) (AMM 65-11-00, 4-2).
b. Discard the Ti-Bolt (6, Fig. 1).
c. Install a Ti-Bolt (6, Fig. 1) with an identifiable manufacturer monogram that is
clearly not "D" (AMM 65-11-00, 4-2).
PAGE 8 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
6x3
5
View A
3x3
2x3  4
1x3
3x3  2x3
2x3  3x3
7
— B
1x3
2x3
8  3x3  Detail B
1 x3  4N 2520
1 Ti-Bolt  L535M3001201
2 Nut
3 Washer
10 1
4 Flexible coupling
5 Long drive shaft adapter
6 Ti-Bolt  L535M3001201
7 Forward drive shaft adapter
8 Flexible coupling
9 Coupling flange
10 Manufacturer monogram
The manufacturer monogram may not appear exactly as shown.
If confirmation is needed contact your Airbus Helicopters customer support.
Inspection of the forward drive shaft
Figure 1
Revision 0, 2020-05-04  PAGE 9 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
З.В.З  Inspection of the AFT drive shaft
1. Inspect the manufacturer monogram (10, Fig. 2) marked on the head of each
TI-Bolt (1):
a. If the manufacturer monogram (10, Fig. 2) can be identified and is clearly not
"D", proceed in accordance with Section 3.B.3.3.
b. If the manufacturer monogram (10, Fig. 2) is "D", replace the Ti-Bolt (1) in
accordance with Section 3.B.3.2.
c. If the manufacturer monogram (10, Fig. 2) cannot be identified due to paint
covering, remove the paint that covers the manufacturer monogram (10)
from the head of the Ti-Bolt (1) in accordance with Section 3.B.4.
d. If the manufacturer monogram (10, Fig. 2) cannot be identified, replace the
Ti-Bolt (1) in accordance with Section 3.B.3.2.
2. Replacement of the Ti-Bolt (1, Fig. 2):
a. Remove the Ti-Bolt (1, Fig. 2) (AMM 65-11-00, 4-2).
b. Discard the Ti-Bolt (1, Fig. 2).
c. Install a Ti-Bolt (1, Fig. 2) with an identifiable manufacturer monogram that is
clearly not "D" (AMM 65-11-00, 4-2).
3. Inspect the manufacturer monogram (10, Fig. 2) marked on the head of each
Ti-Bolt (7):
a. If the manufacturer monogram (10, Fig. 2) can be identified and is clearly not
"D', proceed in accordance with Section 3.B.5 to accomplish PART II or 3.B.6
to accomplish the final steps of PART I.
b. If the manufacturer monogram (10, Fig. 2) is "D", replace the Ti-Bolt (7) in
accordance with Section 3.B.3.4.
c. If the manufacturer monogram (10, Fig. 2) cannot be identified due to paint
covering, remove the paint that covers the manufacturer monogram (10)
from the head of the Ti-Bolt (7) in accordance with Section 3.B.4.
d. If the manufacturer monogram (10, Fig. 2) cannot be identified, replace the
Ti-Bolt (7) in accordance with Section 3.B.3.4.
4. Replacement of the Ti-Bolt (7, Fig. 2):
a. Remove the Ti-Bolt (7, Fig. 2) (AMM 65-11-00, 4-3).
b. Discard the Ti-Bolt (7, Fig. 2).
c. Install a Ti-Bolt (7, Fig. 2) with an identifiable manufacturer monogram that is
clearly not "D" (AMM 65-11-00, 4-3).
d. Proceed in accordance with Section 3.B.5 to accomplish PART II or 3.B.6 to
accomplish the final steps of PARTI.
PAGE 10 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
5x3
4x3
9
View A  7x3
8
6  5x3
4x3
5x3
4x3
1 x3
1x3  2  1 x3
B  Detail B
4x3  85 2520
5x3
1 Ti-Bolt  L535M3001201
Long drive shatt adapter
Flexible coupling
10 1
4  Washer
5  Nut
6 AFT drive shaft adapter
7 Ti-Bolt  L535M3001201
8 Flexible coupling
9 Input drive flange
10 Manufacturer monogram
The manufacturer monogram may not appear exactly as shown.
If confirmation is needed contact your Airbus Helicopters customer support.
Inspection of the AFT drive shaft
Figure 2
Revision 0, 2020-05-04  PAGE 11 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
3.B.4 Removal of the paint from the head of the Ti-Bolt
A CAUTION
MAKE SURE THAT AS MUCH PAINT AS POSSIBLE
REMAINS ON THE HEAD OF THE TI-BOLT. REMOVE
ONLY  THE  PAINT THAT COVERS  THE
MANUFACTURER MONOGRAM ON THE HEAD OF
THE TI-BOLT.
A CAUTION
DO NOT GRIND THE HEAD OF THE TI-BOLT. ONLY
CLEANING AGENT CM 203 AND CLEANING AGENT
CM 217 ARE PERMITTED TO REMOVE THE PAINT
FROM THE HEAD OF THE TI-BOLT.
NOTE  It is not required to re-apply paint on the head of the Ti-Bolt.
1. Partially remove the paint that covers the manufacturer monogram from the
head of the Ti-Bolt, using cleaning agent (CM 203) or cleaning agent (CM 217)
and a scraper (AMM 02-00-00, 2-10).
2. Go back to the appropriate Section (3.B.2.1 or 3.B.2.3 or 3.B.3.1 or 3.B.3.3) and
do the inspection of the manufacturer monogram again.
PART II
З.В.5  Inspection of the AFT connection of ball bearing control
EFFECTIVITY  All helicopter except S/N 2075.
1. Inspect the manufacturer monogram (5, Fig. 3) marked on the head of each
TI-Bolt (4):
a. If the manufacturer monogram (5, Fig. 3) can be identified and is clearly not
"D", proceed in accordance with Section 3.B.6.
b. If the manufacturer monogram (5, Fig. 3) is "D", replace the Ti-Bolt (4) in
accordance with Section 3.B.5.2.
c. If the manufacturer monogram (5, Fig. 3) cannot be identified, replace the
Ti-Bolt (4) in accordance with Section 3.B.5.2.
2. Replacement of the Ti-Bolt (4, Fig. 3):
a. Remove the Ti-Bolt (4, Fig. 3) (AMM 67-20-00, 4-11).
b. Discard the Ti-Bolt (4, Fig. 3).
c. Install a Ti-Bolt (4, Fig. 3) with an identifiable manufacturer monogram that is
clearly not "D" (AMM 67-20-00, 4-11).
PAGE 12 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
View A
Detail B
4x2
1 Flex ball
2 Yaw actuator
3 Adapter
4 Ti-Bolt  EN3308H060028F
5 Manufacturer monogram
The manufacturer monogram may not appear exactly as shown.
If confirmation is needed contact your Airbus Helicopters customer support.
Inspection of the AFT connection of ball bearing control
Figure 3
Revision 0, 2020-05-04  PAGE 13 of 14
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB EC135H-00A-002
3.В.6  Final steps
PART I and PART I|
1. Install the tail rotor drive shaft fairing (AMM 53-50-01, 4-1).
PARTI
2. Install the service cover on the rear structure (AMM 52-40-00, 4-6).
3. Install air deflector (AMM 71-32-00, 4-2).
4. Install aft LH and RH engine cowlings (AMM 71-11-00, 4-3).
5. Install center engine cowling (AMM 71-11-00, 4-2).
6. Install LH and RH engine cowling (AMM 71-11-00, 4-1).
7. Install LH and RH transmission fairing (AMM 71-11-00, 4-4).
З.С  COMPLIANCE CONFIRMATION
Compliance with this document:
PARTI
Confirm accomplishment of PART I of this ASB by an entry in the historical record of
the helicopter.
PART II
Confirm accomplishment of PART Il of this ASB by an entry in the historical record of
the helicopter.
Please confirm compliance with this ASB after accomplishment of PART I and PART II:
QR-Code or hypertext link
NOTE
The recording of compliance with ASB in the R-Tex
tool does not replace the recording in the helicopter
documents
ASB EC135H-00A-002
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
None.
4  APPENDIX
None.
PAGE 14 of 14  Revision 0, 2020-05-04
This document is available on the internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
