# Airbus Helicopters Alert Service Bulletin EC155-34A033: Revision 2

- Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2019-1099; AD 2020-15-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Airbus Helicopters Alert Service Bulletin EC155-34A033](https://openairdocs.org/service-documents/airbus-helicopters/ec155-34a033.md)
- Title as filed: Airbus ASB No EC155-34A033 Rev 2 (IBR)
- Pages: 15
- PDF: https://openairdocs.org/files/sha256/f8/b4/f8b4e2d9de7d2d4fa872602aac85c65633de450f636278984d8d87702dde8960
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec155-34a033/file/f8b4e2d9de7d

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Civil versions: B, B1
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
NAVIGATION - Attitude and Heading Reference System (AHRS)
Modification of the wiring of the FLIGHT/GROUND logic (connector 11 ALPHA)
Corresponds to modifications 365A084754.00 and 365A084754.01
For the attention of
Revision No.  Date of issue
Revision O  2017-07-19
Revision 1  2017-10-09
Revision 2  2018-01-30
Summary:
The purpose of this ALERT SERVICE BULLETIN is to correct the connections of the FLIGHT/GROUND logic of the
primary reference system Attitude and Heading Reference System AHRS), the FCDS (Flight and Control Display
System) and the SSCVFDR (Combined Voice and Flight Data Recording System) by modifying the connection and,
as per configuration, by modifying the wiring of connector 11 ALPHA.
Reason for last Revision:
The purpose of the revision of this ALERT SERVICE BULLETIN is to clarify the information in the post installation
verification procedure, notably for AFCS messages: "FLIGHT DETECT" and "GROUND DETECT" which are
displayed shortly on the VEMD, and are therefore difficult to perceive by the operator.
Compliance:
Airbus Helicopters makes compliance with this ALERT SERVICE BULLETIN mandatory.
Revision 0 2017-07-19  Page 1/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters POST MOD 0722B51 and PRE MOD 0731B89 (SSCVFDR upgraded following standard ED112),
and PRE MOD 365A084754.00,
OR
Helicopters POST MOD 0722B51 and POST MOD 0731B89 (SSCVFDR upgraded following standard
ED112), and PRE MOD 365A084754.00 and 365A084754.01.
NOTE
Refer to the Aircraft Individual Inspection Record (or RIC
AMS) to identify the actual modification status of the aircraft.
1.A.2. Non-installed equipment or parts
Not applicable.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Revision 0:
During a flight test for repair, a difference was found in the attitude indications provided by AHRS and
displayed on the pilot and copilot PFD (Primary Flight Display) and the standby horizon during rapid turn
changes of the helicopter.
This difference of indication is due to a wiring anomaly in the FLIGHT/GROUND logic from the management
card of FLIGHT/GROUND states, as the AHRS have a different dynamic according to the FLIGHT or
GROUND state of the helicopter.
The analysis of this incident showed that the AHRS were receiving the same FLIGHT/GROUND signal of the
same position sensor of the landing gear whereas each AHRS must receive information from a different
source to avoid displaying erroneous attitudes and vertical speed on both PFD. This absence of segregation
in the acquisition of the FLIGHT/GROUND information also affects the FCDS (Flight Control Display System)
system which includes FCDM (Flight Control Display Module), SMD45 pilot screens, and for helicopters
POST MOD 0731B89, the recorder L3-COM FA5001-ED112.
To correct the existing common mode in the acquisition of the FLIGHT/GROUND information used by the
AHRS, the FCDS system and the recorder L3-COM FA5001-ED112, Airbus Helicopters developed the
modifications:
- 365A084754.00 which consists in re-allocating the electronic card outputs by modifying the connection to
connector 11 ALPHA (helicopters PRE and POST MOD 0731B89),
- 365A084754.01 which consists in modifying the wiring of connector 11 ALPHA (helicopters POST MOD
0731B89).
Revision 0  2017-07-19  Page 2/15
Revision 2  2018-01-30  This document is available on the Internet: www.airb  licopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Revision 1:
The purpose of the revision of this ALERT SERVICE BULLETIN is to specify the configurations of helicopters
concerned and to update information in the post installation verification procedure.
Revision 1 does not affect compliance with the previous revision of this ALERT SERVICE BULLETIN for
POST MOD 0722B51 helicopters having applied successfully the procedure of the previous revision.
Revision 2:
The purpose of the revision of this ALERT SERVICE BULLETIN is to clarify the information in the post
installation verification procedure, notably for AFCS messages: "FLIGHT DETECT" and "GROUND
DETECT" which are displayed shortly on the VEMD, and are therefore difficult to perceive by the operator.
Figure 2 has been updated: terminal 6 has become terminal 2 on 11ALP2-DP1.
Revision 2 does not affect compliance with the previous revision of this ALERT SERVICE BULLETIN for
POST MOD 0722B51 helicopters on which the procedure of the previous revision was successfully complied
with.
Airbus Helicopters makes compliance with this ALERT SERVICE BULLETIN mandatory.
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
Helicopters POST MOD 0722B51 and PRE MOD 0731B89: (compliance with modification 365A084754.00)
- modifying the connection to connector 11 APLHA,
- performing the associated tests.
Helicopters POST MOD 0722B51 and POST MOD 0731B89: (compliance with modifications 365A084754.00
and 365A084754.01)
- modifying the connection to connector 11 APLHA,
- modifying the wiring to connector 11 APLHA,
- performing the associated tests.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Helicopters/installed equipment or parts:
Airbus Helicopters makes compliance with the instructions given in paragraph 3. of this ALERT SERVICE
BULLETIN mandatory before the delivery of the helicopter.
Non-installed equipment or parts:
Not applicable.
Revision 0 2017-07-19  Page 3/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
1.E.2. Compliance in service
The work must be performed on the helicopter by the Operator.
Helicopters/installed equipment or parts:
Airbus Helicopters makes compliance with this ALERT SERVICE BULLETIN mandatory.
For helicopters POST MOD 0722B51 and PRE MOD 0731B89, comply with paragraph 3 (except for
3.B.2.b.), within 12 months as from receipt of this ALERT SERVICE BULLETIN, issued on the date
mentioned in the page footer.
For helicopters POST MOD 0722B51 and POST MOD 0731B89, comply with paragraph 3 (except for
3.B.2.a.), within 12 months as from receipt of this ALERT SERVICE BULLETIN, issued on the date
mentioned in the page footer.
Non-installed equipment or parts:
Not applicable.
1.F. APPROVAL
Approval of modifications:
The information or instructions relate to modifications 365A084754.00 and 365A084754.01, which were
approved on July 17, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil
version helicopters subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on July 18, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on October 06, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved
on January 29, 2018 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
1.G. MANPOWER
• For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following
personnel qualifications:
Qualifications:  1 Electrical Technician.
1 Avionics Technician.
Revision 0 2017-07-19  Page 4/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations: 2 hours approximately for Electrical Technician for compliance with modification
365A084754.00.
2 hours approximately for Electrical Technician for compliance with modification
365A084754.01.
3 hours approximately for Avionics Technician (with jacking of the helicopter).
Helicopter downtime is estimated at approximately 1 day.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
The following documents are required for compliance with this ALERT SERVICE BULLETIN:
- AMM: 07.10.00.581: Lifting the Helicopter on Jacks
- AMM: 24.00.00.911: General Safety Instructions - Electrical Power
- AMM: 24.00.00.481: Power Supply - Electrical Power Systems
- AMM: 34.00.00.911: General Safety Instructions - Navigation System
- AMM: 34.23.00.721: Functional Tests - Primary Reference System
- MTC: 20.07.01.201: Handling of helicopters in a hangar and in a prepared area
- MTC: 20.07.02.201: Helicopter parked in a repair shop
- MTC: 20.07.03.406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions
- MTC: 20.07.03.408: Appearance checks on an aircraft after an inspection or repair
- MTC: 20.80.20.101: Contact Insertion and Extraction Method and Tools
- MTC: 20.80.20.441: Installation of electrical cable bundles and optical fibres
1.L. OTHER AFFECTED PUBLICATIONS
The modifications will be incorporated in:
- Wiring Diagram Manual (WDM),
- Special Index Modification (SIM).
These documents will be updated during a future revision.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
Revision 0 2017-07-19  Page 5/15
Revision 2  2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
For any information concerning modification kits and/or components or for assistance, contact the Sales and
Customer Relations Department.
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Components to be ordered for one helicopter POST MOD 0731B89:
New  Former
Designation  Qty  Item
P/N  P/N  Instruction
Extension  2  E0541-10
Cap  1  E0737B0816  2
NOTE 3
The components listed in the table above concern the
modification of the wiring of connector 11ALPHA
(modification 365A084754.01). These components are not
necessary for helicopters PRE MOD 0731B89.
Revision 0  2017-07-19  Page 6/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Equipment or parts to be ordered separately for one helicopter POST MOD 0731B89:
New  Former
Designation  Qty  P/N  Item  P/N  Instruction
Wire, electrical  2 m  EN2267-010A002S
NOTE 4
The equipment or parts listed in the table above concern the
modification of the wiring of connector 11 ALPHA
(modification 365A084754.01). Electrical wire (3) is not
necessary for helicopters PRE MOD 0731B89.
Consumables to be ordered separately:
As per Work Cards and Tasks mentioned in this ALERT SERVICE BULLETIN.
The consumables can be ordered separately from the KLX AEROSPACE SOLUTIONS company.
Website:  https://www.klxaerospace.com/klxaero/
Telephone:  +1.305.925.2600
AOG:  +1.305.471.8888
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2017-07-19  Page 7/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Read and comply with the instructions for handling helicopters in a hangar as per MTC Work Card
20.07.01.201.
- Read and comply with the instructions for helicopters parked in a repair shop as per MTC Work
Card 20.07.02.201.
- Read and comply with the technical instructions applicable when working on an aircraft electrical circuit and
with ground power generating systems as per MTC Work Card 20.07.03.406.
- Read and comply with the instructions on contact insertion and extraction method and tools as per MTC
Work Card 20.80.20.101.
- Read and comply with the instructions for installing electrical cable bundles as per MTC Work
Card 20.80.20.441.
3.B. WORK STEPS
CAUTION
BEFORE STARTING WORK ON THE ELECTRICAL
SYSTEMS, READ TASK 24-00-00-911.
CAUTION
BEFORE STARTING WORK ON THE NAVIGATION
INSTALLATIONS, READ TASK 34-00-00-911.
3.B.1. Preliminary steps
- Install suitable access means
- Remove and/or open all cowlings, panels, doors and equipment as required for access to work zones.
3.B.2. Procedure (Figure 1)
3.B.2.a. Helicopters POST MOD 0722B51 and PRE MOD 0731B89
- Modify the connection to connector 11 ALPHA as per Figure 1
3.B.2.b. Helicopters POST MOD 0722B51 and POST MOD 0731B89
- Modify the connection to connector 11 ALPHA as per Figure 1.
- Modify the wiring to connector 11 ALPHA as per Figure 2
3.B.3. Final steps
- Carry out appearance checks on an aircraft after an inspection or repair as per MTC Work
Card 20.07.03.408.
- Install and/or close all cowlings, panels, doors and equipment removed and/or opened during preliminary
steps (paragraph 3.B.1.).
- Remove the access means.
Revision 0  2017-07-19  Page 8/15
Revision 2  2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
3.B.4. Tests
For helicopters:
- Perform the "tests following modification of FLIGHT/GROUND wiring on the rear landing gear struts" as per
Appendix 4.A
- Perform the functional tests of the primary reference system as per AMM Task 34.23.00.721.
- Reset helicopter into flight condition.
3.C. COMPLIANCE CONFIRMATION
Compliance with this document:
Record compliance with this ALERT SERVICE BULLETIN with the Revision number in the helicopter
documents.
Tracking of modifications in the documentation:
Helicopters POST MOD 0722B51 and PRE MOD 0731B89:
Record compliance with modification 365A084754.00 in the aircraft documents.
Helicopters POST MOD 0722B51 and POST MOD 0731B89:
Record compliance with modifications 365A084754.00 and 365A084754.01 in the aircraft documents.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2017-07-19  Page 9/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
PRE MOD 365A084754.00
11ALP2-CP1
11 ALPHA  1UW22E
VOL 1  - 1UW25NE
.. 1FF4E .
VOL 5  . 1FF45NE
. 1UW28E
VOL 7  . 1UW29E
11ALP2-DP1
2UW22E
VOL 2  2UW25NE
2FF4E
VOL 6  2FF45NE
POST MOD 365A084754.00
11ALP2-CP1
5  . 1UW22E
VOL 5
1UW25NE
7  . 1FF4E
VOL 7  1FF45NE
1UW28E
VOL 1  1UW29E
11ALP2-DP1
2UW22E
VOL 6
6  2UW25NE
.. 2FF4E
VOL 2  2  2FF45NE
Figure 1
Revision 0 2017-07-19  Page 10/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
POST MOD 0731B89
POST MOD 365A084754.00
PRE MOD 365A084754.01
11 ALPHA
11ALP2-DP1
44N-4  2FF45NE
10DEL33-AP1
- 2UW39E
_ 2UW38E
10DEL10-AP1
_ 2RK368E
13R-3
POST MOD 0731B89
POST MOD 365A084754.00
POST MOD 365A084754.01
11ALP2-DP1
44N-4 E  - 2FF45NE  ¡EPX
PERA
10DEL33-AP1
- 2UW39E.
- 2UW38E
10DEL10-AP1
- 2RK368E -  R
13R-3 2
Figure 2
Revision 0 2017-07-19  Page 11/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
4.  APPENDIX
4.A.  TESTS FOLLOWING MODIFICATION OF THE FLIGHT/GROUND WIRING ON THE REAR
LANDING GEAR STRUTS
Although this ALERT SERVICE BULLETIN has no impact on the AFCS function, a check of the
flight/ground logics has been integrated to ensure non-regression of this modification in the AFCS behavior.
Do not use AFCS maintenance mode to display the requested messages.
4.A.1. Preliminary steps
- Energize the helicopter using the electrical power bench as per Sub-task 24-00-00-481-002 of
Task 24-00-00-481.
- Make sure that:
• "AP" pushbutton on the APMS control unit shows an amber "OFF",
• following equipment are energized and initialized : FCDM1, FCDM2, ADC1, ADC2, AHRS1, AHRS2,
PFD1, PFD2, ICP1 and ICP2
4.A.2. Procedure
CAUTION
DO NOT ACTIVATE THE CVFDR MAINTENANCE
COMMAND.
CAUTION
FOR CHECKING THE CVFDR OPERATION, IT IS
NECESSARY TO RESPECT THE RIPS DISCHARGE
TIME OF 10 MINUTES.
CAUTION
DO NOT ENGAGE THE AUTOPILOT.
CAUTION
DO NOT PRESSURIZE THE HYDRAULIC POWER
SYSTEM.
- Jack up helicopter as per Sub-task 07-10-00-581-001 of Task 07-10-00-581.
- Disconnect electrical connectors "9G" (LH landing gear) and "10G" (RH landing gear).
4.A.2.a. LH landing gear to FLIGHT position / RH landing gear to FLIGHT position
- On LH landing gear, make a shunt between "D" and "E" (fixed connector) in order to simulate the
FLIGHT position.
- On RH landing gear, make a shunt between "D" and "E" (fixed connector) in order to simulate the
FLIGHT position.
- Energize the helicopter electrical system.
Revision 0 2017-07-19  Page 12/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Acquisition of FCDM information on SMD45
- Turn off then on the 4 screens.
- Make sure that the cockpit symbols are displayed ("T" must not be displayed).
Acquisition of AHRS information
- On the AHRS control box, set "AHRS 1" to "OFF" then to "ON".
- Make sure that AHRS 1 switches to alignment then displays the information after approx. 1 minute and
5 seconds on both copilot screens.
- On the AHRS control box, set "AHRS 2" to "OFF" then to "ON".
- Make sure that AHRS 2 switches to alignment then displays the information after approx. 1 minute and
5 seconds on both pilot screens.
Checking AFCS logics
- Press the VEMD "SCROLL" key twice to display the AFCS line on the lower screen of the VEMD
the "PFTNOT EXEC" message is displayed.
Remove the shunts between "D" and "E" (fixed connector) on the LH landing gear AND the RH landing
gear AND wait 1 mn.
Do not take into account the other messages displayed on the AFCS line of the VEMD.
On the RH landing gear (10G) make a shunt between "D" and "E" (fixed connector) then the LH landing
gear (9G), make a shunt between "D" and "E" (fixed connector).
• Make sure that the "FLIGHT DETECT" wording is displayed on the AFCS line of the VEMD, alternating
with "PFTNOT EXEC" during 3s, then disappears.
Validation of the START/STOP logic: CVFDR L3 COM - ED112 (helicopters POST MOD 0731B89)
Make sure that the CVFDR operates: the lights "CVR", "FDR" and "HUMS" must go off.
- Make sure that if one or the other of the 2 CVFDR circuit breakers is de-activated, the CVFDR remains
active.
4.A.2.b. LH landing gear to GROUND position / RH landing gear to FLIGHT position
De-energize the helicopter electrical system.
• On LH landing gear, remove the shunt between "D" and "E" (fixed connector) in order to simulate the
GROUND position.
- Energize the helicopter electrical system.
Acquisition of FCDM information on SMD45
- Turn off then on the 4 screens.
- Make sure that the cockpit symbols are displayed ("T" must not be displayed).
Checking AFCS logics
- Press the VEMD "SCROLL" key twice to display the AFCS line on the lower screen of the VEMD,
the "PFTNOT EXEC" wording is displayed.
- Make sure that the "GROUND FLIGHT" wording is displayed on the AFCS line of the VEMD, alternating
with "PFTNOT EXEC" during 3s, then disappears.
Validation of the START/STOP logic: CVFDR L3 COM - ED112 (helicopters POST MOD 0731B89)
- Make sure that the CVFDR operates: the lights "CVR", "FDR" and "HUMS" must go off.
- Make sure that if one or the other of the 2 CVFDR circuit breakers is de-activated, the CVFDR remains
active.
Revision 0 2017-07-19  Page 13/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
4.A.2.c. LH landing gear to FLIGHT position / RH landing gear to GROUND position
• De-energize the helicopter electrical system.
- On LH landing gear, make a shunt between "D" and "E" (fixed connector) in order to simulate the
FLIGHT position.
- On RH landing gear, make a shunt between "D" and "F" (fixed connector) in order to simulate the
GROUND position.
- Energize the helicopter electrical system.
Acquisition of FCDM information on SMD45
- Turn off then on the 4 screens.
- Make sure that the cockpit symbols are displayed ("T" must not be displayed).
Checking AFCS logics
- Press the VEMD "SCROLL" key twice to display the AFCS line on the lower screen of the VEMD,
the "PFTNOT EXEC" wording is displayed.
- Make sure that the "FLIGHT GROUND" wording is displayed on the AFCS line of the VEMD, alternating
with "PFTNOT EXEC" during 3s, then disappears.
Validation of the START/STOP logic: CVFDR L3 COM - ED112 (helicopters POST MOD 0731B89)
- Make sure that the CVFDR operates: the lights "CVR", "FDR" and "HUMS" must go off.
- Make sure that if one or the other of the 2 circuit breakers of the CVFDR is de-activated, the CVFDR
remains active.
4.A.2.d. LH landing gear to GROUND position / RH landing gear to GROUND position
NOTE
Provide access to the MGB for this test phase in order to act
on lug "16E".
- De-energize the helicopter electrical system.
- On LH landing gear, remove the shunt between "D" and "E" (fixed connector).
- On RH landing gear, remove the shunt between "D" and "F" (fixed connector).
Connect electrical connectors "9G" (LH landing gear) and "10G" (RH landing gear).
- Jack down helicopter as per Sub-task 07-10-00-581-001 of Task 07-10-00-581.
- Energize the helicopter electrical system.
Acquisition of FCDM information on SMD45
- Turn off then on the 4 screens.
- Make sure that a "T" is displayed on the 4 screens for some seconds and then that the cockpit symbols
are displayed (initialization phase longer than in flight).
Acquisition of AHRS information
- On the AHRS control box, set "AHRS 1" to "OFF" then to "ON".
- Make sure that AHRS 1 switches to alignment then displays the information after approx. 30 seconds on
both copilot screens.
- On the AHRS control box, set "AHRS 2" to "OFF" then to "ON".
- Make sure that AHRS 2 switches to alignment then displays the information after approx. 30 seconds on
both pilot screens.
Revision 0 2017-07-19  Page 14/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-34A033
Checking AFCS logics
- Press the VEMD "SCROLL" key twice to display the AFCS line on the lower screen of the VEMD,
the "PFTNOT EXEC" wording is displayed
- Disconnect electrical connector "10G" (RH landing gear) AND wait 1 mn.
- Do not take into account the display on AFCS line of the VEMD.
- Reconnect electrical connector "10G" on RH landing gear.
- Make sure that the "GROUND DETECT wording is displayed on the AFCS line of the VEMD, alternating
with "PFTNOT EXEC" during 3s, then disappears.
Validation of the START/STOP logic: CVFDR L3 COM - ED112 (helicopters POST MOD 0731B89)
- On the MGB, disconnect lug "16E" in order to simulate the MGB oil pressure.
- Wait for RIPS discharge (10 minutes).
- Make sure that the CVFDR operates: the lights "CVR", "FDR" and "HUMS" must go off.
- Make sure that if one or the other of the 2 CVFDR circuit breakers is de-activated, the CVFDR remains
active.
- On the MGB, connect lug "16E".
- Make sure that the CVFDR does not operate: the lights "CVR" and "FDR" are on.
4.A.3. Final steps
- De-energize the helicopter electrical system as per Sub-task 24-00-00-481-002 of Task 24-00-00-481.
Revision 0 2017-07-19  Page 15/15
Revision 2 2018-01-30  This document is available on the Internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
