# Eurocopter Alert Service Bulletin EC155-53A031

Copy: Revision 1 ("U.S. DOT/FAA - Eurocopter ASB No  EC155-53A031"), 33 pages: PDF https://openairdocs.org/files/sha256/76/9c/769c63235a5cf1e7524fff9da93f8af660648f49a61a2b315a7887459f6138b1; text https://openairdocs.org/service-documents/airbus-helicopters/ec155-53a031/file/769c63235a5c.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-1214; AD 2013-12-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC155-53A031
- Latest revision known: EC155-53A031, Revision 1, dated September 21, 2011 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec155-53a031

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-12-04](https://openairdocs.org/ad/2013-12-04.md), effective Aug 2, 2013: Revision 1

## Text (33 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-1214; AD 2013-12-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
Civil versions: B, B1
ALERT SERVICE BULLETIN
SUBJECT: FUSELAGE
Draining tank box area
Corresponds to modifications 0745C96, 0753C98,
365A084485.00
For the attention of
Revision No.  Date of issue
Revision 0  2011-05-03
Revision 1  2011-09-21
Summary:
Modification to draining system of tank boxes.
For aircraft equipped with emergency buoyancy FP (Fixed Parts), this modification consists of:
- canceling one drain plug per fuel tank compartment in order to make drain possible (except for center tanks),
- creating a new drain point for each RH and LH center tank compartment,
- installing self-sealing drain valves replacing previously-removed drain plugs or on newly-performed drains, in
order to guarantee compartment sealing in case of ditching.
For aircraft not equipped with emergency buoyancy FP, this modification consists of:
- canceling one drain plug per fuel tank compartment in order to make drain possible.
Reason for last revision:
- For aircraft equipped with emergency buoyancy FP:
• propose a new operational procedure to create new drain points without disassembling center tanks.
- Take into account customer feedback.
Compliance:
Compliance with this Alert Service Bulletin is mandatory.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 1/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 2 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1. PLANNING INFORMATION
• CAUTION
THE INFORMATION AND INSTRUCTIONS IN THIS
SERVICE  BULLETIN  ARE  INTENDED  FOR
MAINTENANCE PERSONNEL.
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment
Helicopters:
- pre-modifications 0753C98 and 0745C96,
or
- pre-modification 365A084485.00.
1.A.2. Non-installed equipment
Not applicable.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
The purpose of this Alert Service Bulletin Revision 0 was to improve draining of the helicopter tank boxes by:
- canceling some drain plugs in order to drain tank compartments,
- installing self-sealing drain valves for aircraft equipped with buoyancy FP.
The purpose of this Alert Service Bulletin Revision 1 is to:
- in order to reduce the grounding time, propose for aircraft equipped with emergency buoyancy FP and
panels under bottom structure (u) (see photo page 11), a new operational procedure to create new drain
points without disassembling center tanks,
- take into account customers feedback.
NOTE
Aircraft not equipped with panels under bottom structure (u)
must mandatorily disassemble center tanks to create new
drain points.
Revision 1 of this Alert Service Bulletin does not question compliance with Revision 0.
Revision 1 of this Alert Service Bulletin will be subject to EASA Airworthiness Directive.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 2/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 3 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1.D. DESCRIPTION
For aircraft equipped with emergency buoyancy FP:
- remove drain plug located on:
• front tanks at X2800 / Y570 and Y-570,
• intermediate tank at X4920 / Y360,
• rear tank (if equipped) at X5927 / Y-73,
- create two new drain points (on the center tanks) at X3207 / Y408 and Y-408,
- install a self-sealing drain valve on:
. front tanks at X2800 / Y570 and Y-570,
center tanks at X3207 / Y408 and Y-408,
. intermediate tank at X4920 / Y360,
. rear tank at X5927 / Y-73.
For aircraft not equipped with emergency buoyancy FP:
- remove drain plug located on:
• front tanks at X2800 / Y570 et Y-570,
• center tanks at X3193 / Y576 et Y-576,
. intermediate tank at X4920 / Y360,
. rear tank (if equipped) at X5927 / Y-73.
1.E. COMPLIANCE
1.E.1. Compliance at the works
1.E.1.a. Helicopters/installed equipment
According to facilities installed or not on the aircraft (emergency buoyancy FP and/or the 6th tank), comply
with the different paragraphs of Paragraph 3.B. of this Alert Service Bulletin.
NOTE
Modifications 0753C98 and 0745C96 (if aircraft equipped
with buoyancy FP) are incorporated in the definition of new
helicopters delivered from January 01, 2012. This date is
given for information only, refer to the Individual Inspection
Log Book (RIC-AMS), the Equipment Log Cards (FM) or the
aircraft Log Book to identify the actual modification status of
1.E. 1.b. Non-installed equipment
Not applicable.
1.E.2. Compliance in service
1.E.2.a. Helicopters/installed equipment
EUROCOPTER makes mandatory compliance with this Alert Service Bulletin.
The works must be performed on helicopter by the Operator.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 3/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 4 (OCR)

• EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1.E.2.a.1. Helicopters equipped with emergency buoyancy FP
Apply § 3. except § 3.B.2.b., within 24 months as from receipt of this Alert Service Bulletin, published at
the date mentioned in page footer.
1.E.2.a.2. Helicopters not equipped with emergency buoyancy FP
Apply § 3. except § 3.B.2.a., during the next scheduled inspection without exceeding 110 flight hours as
from receipt of this Alert Service Bulletin, published at the date mentioned in page footer.
1.E.2.b. Non-installed equipment
Not applicable.
1.F. APPROVAL
Approval of modifications:
The information or instructions relating to modification 0753C98 was approved on February 09, 2011 under
the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an
Airworthiness Certificate.
The information or instructions relating to modification 0745C96 was approved on February 09, 2011 under
the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an
Airworthiness Certificate.
The information or instructions relating to modification 365A084485.00 was approved on February 09, 2011
under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to
an Airworthiness Certificate.
Approval of this document:
The technical information contained in this Alert Service Bulletin Revision 0 was approved on April 29, 2011
under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to
an Airworthiness Certificate.
The technical information contained in this Alert Service Bulletin Revision 1 was approved on
September 20, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil
version helicopters subject to an Airworthiness Certificate.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 4/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 5 (OCR)

EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1.G. MANPOWER
1.G.1. Manpower (MOD 0753C98 and 0745C96)
1.G.1.a. Manpower with removal of center tanks
For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel
qualifications:
Qualification: 2 Airframe Technicians.
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations:
- 80 hours approximately for the Airframe Technicians (polymerization time for sealing mixture excluded).
Estimated helicopter grounding time: 10 days approximately.
1.G. 1.b. Manpower without removal of center tanks
For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel
qualifications:
Qualification: 2 Airframe Technicians.
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations:
- 8 hours approximately for the Airframe Technicians (polymerization time for sealing mixture excluded).
Estimated helicopter grounding time:
- 1 day ½ approximately (polymerization time for sealing mixture excluded).
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 5/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 6 (OCR)

EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1.G.2. Manpower (MOD 365A084485.00)
For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel
qualifications:
Qualification: 1 Airframe Technician.
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations:
- 1 hour approximately for the Airframe Technician.
Estimated helicopter grounding time: 1 hour ½ approximately.
1.H. WEIGHT AND BALANCE
1.H.1. Weight and balance (MOD 0753C98)
Weight: Weight negligible.
Moment: Moment negligible.
1.H.2. Weight and balance (MOD 0745C96)
Weight: + 0.228 kg.
Moment:
- Longitudinal moment: + 1.29 m.kg.
- Lateral moment: + 0.01 m.kg.
1.H.3. Weight and balance (MOD 365A084485.00)
Weight: Weight negligible.
Moment: Moment negligible.
1.I.  EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD
Not applicable.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 6/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 7 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
1.K. REFERENCES
The following documents are required for compliance with this Alert Service Bulletin:
AMM: 05-22-00-213: 15-Hour Inspection,
AMM: 24-00-00-911 : General Safety Instructions - Electrical Power,
AMM: 28-11-03-061 : Removal / Installation - Center Left Fuel Tank,
AMM: 28-11-04-061: Removal / Installation - Center Right Fuel Tank,
MTC:  20.02.05.401: ASSEMBLY - Assembly with rivets.
MTC: 20.02.06.101 : LOCKING AND BLOCKING OF ASSEMBLIES - General.
MTC: 20.02.06.402: LOCKING AND BLOCKING OF ASSEMBLIES - Locking with lockwire.
MTC: 20.03.02.406 : GENERAL RIVET REPLACEMENT PRINCIPLES - "CHERRY-MAX" rivets
A.S.N.A 0077 and 0078.
MTC: 20.06.01.101: BONDING WITH ADHESIVES - General rules for bonding with adhesives.
MTC: 20.06.01.102: BONDING WITH ADHESIVES - Bonding method.
MTC: 20.06.01.411 :  COMPOSITE STRUCTURE REPAIR - BONDING WITH ADHESIVES -
HYSOL EA 9396.
MTC:  20.06.04.101 : USE OF MIXTURES - General information on mixtures.
MTC: 20.06.04.303 : USE OF MIXTURES - Casting No. 11 mixture.
MTC:  20.07.02.201 : SAFETY INSTRUCTIONS - Helicopter parked in a hangar.
MTC: 20.07.03.406 : TECHNICAL INSTRUCTIONS - Instructions applicable when working on an aircraft
electrical circuit or when energizing aircraft power generating systems on ground.
MTC: 20.07.03.408 : TECHNICAL INSTRUCTIONS - General principles applicable for visual cleanliness
and appearance checks on an aircraft after an inspection or a repair.
1.L. DOCUMENTS AFFECTED
Document to be updated:
The modification will be incorporated in the following manuals: IPC and AMM.
Document already updated:
Not applicable.
1.M. INTERCHANGEABILITY AND MIXABILITY BETWEEN THE PARTS
Interchangeability:
Not applicable.
Mixability:
Not applicable.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 7/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 8 (OCR)

- EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
2. MATERIAL INFORMATION
2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
Kits and/or components will be delivered in special pricing conditions until December 31, 2012.
EUROCOPTER
Etablissement de Marignane
Direction VENTES et Relations Client (ECR)
13725 MARIGNANE CEDEX
FRANCE
NOTE
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
aircraft to be modified.
NOTE
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT
For any information concerning the modification kits and/or components or assistance, contact the
EUROCOPTER network's Customer Support Sales Department.
2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT
Kits or components to be ordered for one helicopter or one assembly only if equipped with emergency
buoyancy FP:
Components required for aircraft modification.
Order components listed below according to modifications to be incorporated.
New  Old
Designation  Qty  lt.  Instruction
P/N  PIN
Drain plug support  2  365A21-4019-20  1
Rivet  5  ASNA0078A401  2
(CHERRY-MAX)
3 Self-sealing drain valve  ENCCDM12
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 8/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 9 (OCR)

• EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
Material to be ordered separately:
New  Old
Designation  Qty  PIN  It.  PIN  Instruction
Lockwire  4 m  EN3628-0,8  CM776  4
Products to be ordered separately:
As per Work Cards mentioned in this Alert Service Bulletin and list below:
Designation  Qty  Product P/N  It.
Adhesive compound, 1 L container  0.1 kg  ECS0010.10  CM616  5
(HYSOL EA 9396)
Sealing mixture  0.2 kg  DHS268-112.20  6
(Casting No. 11 mixture)
Material supplied by the operator:
Not applicable.
Material required for non-installed components:
Not applicable.
Specific tooling:
As per Work Cards mentioned in this Alert Service Bulletin.
2.D. MATERIAL TO BE RETURNED
Not applicable.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 9/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 10 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Comply with electrical power supply instructions as per AMM Task 24-00-00-911.
- Refer to safety instructions as per MTC Work Card 20.07.02.201 to park a helicopter in a hangar.
- Use adhesives as per MTC Work Cards 20.06.01.101 and 20.06.01.102.
- Carry out assemblies by riveting as per MTC Work Card 20.02.05.401.
- Carry out assemblies by locking as per MTC Work Card 20.02.06.101.
- During the use of mixtures, be informed of the general information on mixtures as per MTC Work Card
20.06.04.101.
3.B. OPERATIONAL PROCEDURE
3.B.1. Preliminary steps
- Disconnect all electrical supply sources as per MTC Work Card 20.07.03.406.
- Install suitable access means.
- Remove and/or open all panels, padding and equipment as required for easy access to different work
zones.
3.B.2. Procedures
3.B.2.a. Helicopter equipped with emergency buoyancy FP
3.B.2.a. 1. Removal of drain plugs (MOD 0753C98)
As per Figure 1
- Remove the 4 drain plugs (b):
• 1 plug on the front RH tank at X2800 / Y570,
1 plug on the front LH tank at X2800 / Y-570,
• 1 plug on the intermediate tank at X4920 / Y360,
• 1 plug on the rear tank at X5927 / Y-73,
and store them back in the warehouse.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 10/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 11 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
3.B.2.a.2. Installation of new drain points (MOD 0753C98)
Two operational procedures for the installation of new drain points are proposed:
- for aircraft not fitted with panel (u) and symmetrical panel (see Photo below):
. installation of new drain points with removal of center tanks (§ 3.B.2.a.2.a.),
- for aircraft fitted with panel (u) and symmetrical panel (see Photo below):
. installation of new drain points without removal of center tanks (§ 3.B.2.a.2.b.),
NOTE
Panel (u) is located on the RH side of the aircraft (at X3276 /
Y496), a second panel is symmetrically located on the LH
side (at X3276 / Y-496). These two panels allow drain plugs
to be installed without removing center tanks.
For aircraft equipped with panel (u) and symmetrical panel, the selection of either of these operational
procedures is left to the operator's initiative. For aircraft not equipped with panel (u) and symmetrical
panel, removal of center tanks is mandatory.
Photo: panel under bottom structure
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 11/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 12 (OCR)

EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
3.B.2.a.2.a. Installation of new drain points with removal of center tanks
Remove the RH and LH center tanks as per AMM Tasks 28-11-04-061 and 28-11-03-061.
As per Figure 3
NOTE
The procedure below describes the operations to be
performed on the RH side of the aircraft. Operations on the
LH side are symmetrical.
- Drill 1 through hole (G) (both skins of NIDA) to diameter 18 mm.
- Counterdrill hole (G) to diameter 22 mm through the first skin of NIDA (outer side).
- Drill 2 holes (H) to diameter 1.5 mm through the second skin of NIDA (inner side). Both holes will be
used as filling and vent holes for sealing mixture (6).
- Drill NIDA to diameter 26 mm.
- Install drain plug support (1):
. by means of 2 rivets (2) as per MTC Work Card 20.03.002.406,
• by interlaying adhesive compound (5) as per MTC Work Card 20.06.01.411.
- Inject sealing mixture No. 11 (6) through holes (H) and let polymerize as per MTC Work Card
20.06.04.303.
- Perform the same operations (see above-mentioned §) on the LH side of the aircraft.
Install the RH and LH center tanks as per AMM Tasks 28-11-04-061 and 28-11-03-061.
3.B.2.a.2.b. Installation of new drain points without removal of center tanks
NOTE
The procedure below describes the operations to be
performed on the RH side of the aircraft. Operations on the
LH side are symmetrical.
As per Figure 5
- Remove blanking plate (u) and retain its attachments (plate on which a drain plug is positioned)
(Photos A1 and B1).
According to the aircraft equipment, this plate can hold an antenna; in this case, disconnect the
antenna connector.
NOTE
Removal of panel (u) makes it possible to check cleanliness
of the front tank compartment, during and after the
modification.
- Carry out marking/positioning of the new drain plug by taking the dimension (Photo C1):
at + 68 ‡ 2 mm from the theoretical profile of frame at 9°,
at Y408.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 12/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 13 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
• CAUTION
DURING THE PROCEDURE AND PARTICULARLY
DURING DRILLING OPERATIONS (INTERNAL AND
EXTERNAL COATINGS), TREPANNING AND BORING,
MAKE SURE THAT:
- YOU DO NOT DAMAGE THE DIFFERENT EQUIPMENT
- THERE IS NO FOREIGN  (PARTICULARLY THE TANK BODY IN THE TANK  LOCATED  TANK  COMPARTMENT
COMPARTMENT (CHIPS, FILINGS, TOOLS,...),
- THE FUEL TANK COMPARTMENT IS CLEAN.
As per Figure 6
- Inside the tank box, position adhesive tape (aa) on the inner coating of the first drilling (Detail U1 and
Photo V1). This is to prevent chip projection inside the tank box.
- Drill hole G through (external and internal) coatings to diameter 4.2 mm, by respecting perpendicularity
of the drilling with respect to (external and internal) coatings (Photo E1).
- Trepan the external coating to diameter 20 mm (Photo F1).
As per Figure 7
- Drill honeycomb to diameter 37 mm, then clean by suction (Photo G1 and detail D1).
- Trepan the inner coating to diameter 17 mm making sure to machine the coating only without passing
through adhesive tape (aa) previously positioned. The adhesive tape enables filings to be collected
during drilling and trepanning, and prevents any filing projection inside the tank box; these filings
mainly remain trapped in adhesive tape (aa) (Photos H1 and J1, and Detail D1)).
- Remove adhesive tape (aa) and clean the trepanned area (Photo J1).
As per Figure 8
- Position drain plug support (1) and point the 2 rivet holes (2) (Photo K1).
- Drill the 2 rivet holes to diameter 3.2 mm on the external coating and make sure that the honeycomb is
sufficiently drilled on the 2 holes (Photo K1 and Detail Q1).
- Make sure that the area is completely cleaned.
- Bond drain plug support (1) using adhesive compound (5) as per MTC Work Card 20.06.01.411,
positioning it with "Spincers" (ab) (Photo L1, and Details Q1 and R1).
As per Figure 9
- Slowly inject sealing mixture No. 11(6) through the first rivet hole until it goes out through the periphery
of hole diameter 17 mm of the inner coating as per MTC Work Card 20.06.04.303 (Photo M1 and
Detail T1). Rivet firstly drain plug support (1) through the first filling hole by means of a rivet (2) as per
MTC Work Card 20.03.02.406 (Photo P1, and Details S1 and T1):
The operation must be carried out by 2 persons (Photos N1 and M1, Detail T1):
. the first person injects the sealing mixture,
. the second person checks with mirror (ac) (inside the fuel compartment) until the mixture
appears at the periphery of drain plug support (1).
- Clean the excess sealing mixture.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 13/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 14 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
- Then, inject sealing mixture No. 11 (6) through the second rivet hole. Apply the same procedure as
before in order to improve the filling (Photo M1).
- Secondly, rivet drain plug support (1) through the second filling hole with rivet (2) as per MTC Work
Card 20.03.002.406 (Photo P1, and Details S1 and T1).
- Clean the excess sealing mixture.
- Clean the internal and external area and let polymerize.
As per Figure 5
- Re-install blanking plate (u) by means of attachments previously retained (Photo A1). If the antenna
is installed on the plate, reconnect the antenna connector.
Perform the same operations (mentioned in § above) on the LH side of the aircraft.
3.B.2.a.3. Installation of self-sealing drain valves (MOD 0745C96)
As per Figure 4
- Install 6 valves (3):
1 valve on the front RH tank at X2800 / Y570,
1 valve on the front LH tank at X2800 / Y-570,
1 valve on the RH center tank at X3207 / Y408,
1 valve on the LH center tank at X3207 / Y-408,
1 valve on the intermediate tank at X4920 / Y360,
1 valve on the rear tank at X5927 / Y-73,
direct holes (T) of all valves (3) towards the rear of the aircraft,
torque to between 1.3 and 1.7 m.daN (115.1 - 150.5 Ibf.in),
lock all the valves by means of lockwire (4) as per MTC Work Card 20.02.06.402.
3.B.2.b. Helicopter not equipped with emergency buoyancy FP
Removal of drain plugs (MOD 365A084485.00) as per Figure 2
- Remove the 6 drain plugs (b):
1 plug on the front RH tank at X2800 / Y-570,
1 plug on the front LH tank at X2800 / Y-570,
1 plug on the RH center tank at X3193 / Y576,
1 plug on the LH center tank at X3193 / Y-576,
1 plug on the intermediate tank at X4920 / Y360,
• 1 plug on the rear tank at X5927 / Y-73,
and store them back in the warehouse.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 14/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 15 (OCR)

→ EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
3.B.3. Tests
Not applicable.
3.B.4. Final steps
- Remove access means installed in § 3.B.1.
- Perform a visual cleanliness and appearance check as per MTC Work Card 20.07.03.408.
- Reconnect all electrical supply sources disconnected in § 3.B.1 as per MTC Work Card 20.07.03.406.
- Re-install and/or close all the padding, panels and equipment removed and/or opened when restoring the
aircraft to flight conditions (§ 3.B.1.).
3.B.5. Ground run-up / flight test
Not applicable.
3.B.6. Operational procedure on non-installed equipment
Stock retrofitting:
Not applicable.
Stock replacement, stock scrapping and stock building-up:
Stock building-up of spare parts, in particular self-sealing drain valves P/N ENCCDM12, related to the
compliance of this Alert Service Bulletin is left to the operator's initiative.
3.C. IDENTIFICATION
Identification of this document:
Record compliance with this Alert Service Bulletin in the aircraft documents.
Identification of modifications in the documents:
As per incorporated modifications, record compliance with modifications 0753C98 and 0745C96, or
modification 365A084485.00 in the aircraft documents.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 15/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 16 (OCR)

• EUROCOPTER
AN EADS COMPANY  ASB No. EC155-53A031
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
Refer to AMM Task 05-22-00-213 and:
§ 6  FUSELAGE STRUCTURE LH SIDE
Tank compartment and sealed compartments under the
cabin
- Existing drain plugs
- Self-sealing valves (if installed)
§ 12  FUSELAGE STRUCTURE RH SIDE
Tank compartment and sealed compartments under the
cabin
- Existing drain plugs
- Self-sealing valves (if installed)
Open and close.
Check each valve for correct operation by
actuating the float with the push-button.
Open and close.
Check each valve for correct operation by
actuating the float with the push-button.
The Aircraft Maintenance Manual (AMM) will incorporate this instruction at the time of a further revision. After
incorporation of this instruction in the Aircraft Maintenance Manual (AMM), refer to it.
Revision 0 2011-05-03  Approved under EASA DOA No. 21J.056.  Page 16/33
Revision 1 2011-09-21  This document is available on the Internet: www.eurocopter.com/techpub

### Page 17 (OCR)

- YC
× 6630
SECTION  E-E
× 5915
SECTION  D-D
Y 360
× 4880
× 4630
Figure 1
ASB No. EC155-53A031  SECTION  C-C  REAR 9° FRAME DATUM  Page 17/33  Approved under EASA DOA No. 21J.056.  copter.com/techoub  This document is available on the Internet: www.euroc
EUROCOPTER  AN EADS COMPANY  × 1700  2011-05-03  2011-09-21
Revision 0  Revision 1

### Page 18 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 18/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 19 (OCR)

× 6630
SECTION  E-E
SECTION  V-V
X 5915
KE
SECTION  D-D  × 4920
X 4880
KE
× 4630
Figure 2
ASB No. EC155-53A031  SECTION  C-C  Page 19/33  This document is available on the Internet: www.eurocopter.com/techoub
Ko Voy  -Y 576  Y-576  Approved under EASA DOA No. 21J.056.
X 3193*  { 3193
REAR 9° FRAME DATUM
X 2905
570
EUROCOPTER  AN EADS COMPANY  × 1700  Revision 0 2011-05-03  Revision 1 2011-09-21

### Page 20 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 20/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 21 (OCR)

SECTION  K-K
(Drain plug  bracket alone)
FORWARD 9° FRAME DATU
Figure 3
ASB No. EC155-53A031  Page 21/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  × 3207
AN EADS COMPANY  REAR 9° FRAME DATUM  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 22 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 22/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 23 (OCR)

0X014  1,3 - 1,7 daN.m  115.1 - 150.5 in. -Ib
5915
X 4880
POST MOD  X 4630
Figure 4
ASB No. EC155-53A031  -•ÇR  X 3205  Page 23/33  This document is available on the Internet: www.eurocopter.com/techpub
X 2905
Approved under EASA DOA No. 21J.056.
EUROCOPTER  0X07 40  1,3 - 1,7 daN.m  115.1 - 150.5 in.-lb  or s
AN EADS COMPANY  Lay  1,7 daN.m  15.1 - 150.5 in. -1b  2011-05-03  2011-09-21
Revision 0  Revision 1

### Page 24 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 24/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 25 (OCR)

(POST-REMOVAL)
Figure 5
ASB No. EC155-53A031  (PRE-REMOVAL)  9° FRAME DATUM  Page 25/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
→ EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 26 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 26/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 27 (OCR)

aa
REAR 9°FRAME DATUM
aa
Figure 6
ASB No. EC155-53A031  68‡2  Page 27/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
| REAR 9° FRAME DATUM
EUROCOPTER  FORWARD 9° FRAME DATUM
AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 28 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 28/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 29 (OCR)

Figure 7
ASB No. EC155-53A031  REAR 9° FRAME DATUM  Page 29/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techoub
EUROCOPTER  FORWARD 9° FRAME DATUM
AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 30 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 30/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 31 (OCR)

HOLES FOR RIVETS (2)
HOLES FOR RIVETS (2)
Figure 8
ASB No. EC155-53A031  PRI  HOLES FOR RIVETS (2)  Page 31/33  This document is available on the Internet: www.eurocopter.com/techpub
68 +2  Approved under EASA DOA No. 21J.056.
DATUM
EUROCOPTER  VE DATUM
FORWARD 9° FR
AN EADS COMPANY  HOLES  FOR  RIVETS (2)  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 32 (OCR)

ASB No. EC155-53A031  PAGE LEFT BLANK INTENTIONALLY  Page 32/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
EUROCOPTER  AN EADS COMPANY  Revision 0 2011-05-03  2011-09-21
Revision 1

### Page 33 (OCR)

(POST-FILLING)
M1  Figure 9
ASB No. EC155-53A031  S1  Page 33/33  Approved under EASA DOA No. 21J.056.  This document is available on the Internet: www.eurocopter.com/techpub
< REAR 9° FRAME DATUM
(PRE-FILLING)
EUROCOPTER  FORWARD 9° FRAME DATUM
AN EADS COMPANY  2011-05-03  2011-09-21
Revision 0  Revision 1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
