# Airbus Helicopters Alert Service Bulletin EC155-56A006

Copy: No revision named ("Airbus Helicopters ASB EC155-56A006 Rev 0"), 13 pages: PDF https://openairdocs.org/files/sha256/6e/95/6e9540f6ee8f288fbabb0f1f1ea4f160e778302ca8b5e2c4f62a99efc16f1a8d; text https://openairdocs.org/service-documents/airbus-helicopters/ec155-56a006/file/6e9540f6ee8f.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0916; AD 2021-05-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC155-56A006
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec155-56a006

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-05-06](https://openairdocs.org/ad/2021-05-06.md), effective Apr 19, 2021: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec155-56a006/proposed.md).

## Text (13 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0916; AD 2021-05-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
Civil version(s): B, B1
ALERT SERVICE BULLETIN
SUBJECT: WINDOWS - Jettisonable windows
Check of the press-studs on the window jettisoning system
For the attention of
Revision No.  Date of issue
Revision 0  2015-08-10
Summary:
To check and, if necessary, replace the extraction tapes equipped with press-studs on the window jettisoning
system.
Compliance:
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory, except for
paragraph 3.D.
Revision 0 2015-08-10  Page 1/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Table: Helicopters concerned by compliance with this Service Bulletin
Helicopters concerned  Components  concerned  Required conditions for these components
- Equipped with an extraction tape (a) with a press-
Emergency exit  stud (b) (see Figure 1 below).
windows outside  - Identified by a colored surround and by the
EC155 helicopters, all  the cabin)  instructions for jettisoning marked below the
versions  window (photo below given as an example).
All windows  - Equipped with an extraction tape (a) with a press-
(inside the cabin)  stud (b) (see Figure 1 below).
NOTE
The color which identifies the windows (outside the cabin)
varies according to the helicopter.
Outside the cabin
Inside the cabin
Figure 1
Revision 0 2015-08-10  Page 2/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
1.A.2. Non-installed equipment or parts
Not applicable.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
During the assembly of a helicopter on the assembly line, an operator faced difficulties unbuttoning an
extraction tape. This may lead to malfunction of the window jettisoning system.
The jettisoning test scheduled every 2 years for windows on fixed panels and on sliding doors, and every
year for windows on hinged doors, includes the unbuttoning of the press-studs and enables this kind of
difficulty to be detected.
In order to ensure a targeted and systematic check of the press-studs, Airbus Helicopters makes compliance
with this ALERT SERVICE BULLETIN mandatory, except for paragraph 3.D., for all helicopters equipped
with extraction tapes with press-studs, regardless of the operations previously carried out.
1.D. DESCRIPTION
Compliance with this ALERT SERVICE BULLETIN consists in checking and, if necessary, replacing the male
part of the press-studs and/or the extraction tapes equipped with the female part of the press-studs of the
window jettisoning system.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
Revision 0 2015-08-10  Page 3/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
1.E.2. Compliance in service
Helicopters/installed equipment:
Comply with paragraph 3.B.1. within
50 flying hours or 1 month (the first limit
reached is applicable) following receipt of
this ALERT SERVICE BULLETIN, issued on
the date indicated at the bottom of the page
Have you faced any
difficulty unbuttoning a
press-stud?  NO
No further action is required on the
YES  press-stud.
For press-studs located inside the
helicopter, take into account the
instructions and compliance times
specified below:
- Comply with paragraph 3.B.3.
Then,
- Comply with paragraph 3.B.5. the next time the
interior trimming is removed.
Non-installed equipment or parts:
Not applicable.
For press-studs located outside the
helicopter, take into account the
instructions and compliance times
specified below:
- Comply with paragraph 3.B.2.
Then,
- Check the condition of the extraction tape and self-
gripping tape every 15 flying hours until
paragraph 3.B.4. has been complied with:
If necessary, replace the self-gripping tape.
- Comply with paragraph 3.B.4. within 100 flying hours
or 3 months (the first limit reached is applicable)
following compliance with paragraph 3.B.2.
1.F. APPROVAL
Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on August 10, 2015 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters
of civil versions subject to an Airworthiness Certificate.
Revision 0 2015-08-10  Page 4/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following
personnel qualifications:
Qualification: 1 Mechanical Engineering Technician.
The time for the operations is indicated for reference, for a standard configuration.
Time for the operations: - approximately 20 minutes to comply with paragraph 3.B.2. or 3.B.3. on one
window.
- approximately 1 hour to comply with paragraph 3.B.4. or 3.B.5. on one window.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
The documents required for compliance with this ALERT SERVICE BULLETIN are as follows:
Aircraft Maintenance Manual (AMM):
AMM: 56-20-00-062: Windows - Removal / Installation Jettisonable Window on fixed panels
AMM: 56-30-00-062: Windows - Removal / Installation Jettisonable Window on a sliding door
AMM: 56-30-00-064: Windows - Removal / Installation Jettisonable Window on hinged door
Standard Practices Manual (MTC):
MTC: 20.03.04.406: Replacement of self-adhesive self-gripping tapes
1.L. OTHER AFFECTED PUBLICATIONS
Airbus Helicopters will modify the Aircraft Maintenance Manual (AMM) with respect to this ALERT SERVICE
BULLETIN.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
Revision 0 2015-08-10  Page 5/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For any information concerning the components, please contact the Sales and Customer Relations
Department of the Airbus Helicopters Network.
Availability
The components will be delivered on customer's order.
Procurement conditions
Order the required quantity (unless otherwise specified)
from
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
France
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
Not applicable.
Revision 0 2015-08-10  Page 6/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Equipment or parts to be ordered separately:
Former
Designation  Qty  New P/N  Item  PIN  →  Instruction
Extraction tape  AR  As per IPC  1  Discard
Press-stud male
A/R  As per IPC  2  Discard
part
Self-gripping  Local procurement
tape  AIR  ECS2291-A254NOI  3,5
(hook part)  (or equivalent)
Self-gripping  Local procurement
tape  ECS2291-B254NOI  4,6
(loop part)  (or equivalent)
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2015-08-10  Page 7/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
3. ACCOMPLISHMENT INSTRUCTIONS
3.А. GENERAL
Not applicable.
3.B. WORK STEPS
3.B.1. Check of the press-studs located on the extraction tapes of the window jettisoning system (Figures 2 and 3)
Check that the press-studs located on the extraction tapes can be unbuttoned by hand:
- If all the press-studs can be unbuttoned without excessive effort, button them:
. No further action is required.
- For press-studs which cannot be unbuttoned or are difficult to unbutton:
. Outside the helicopter, comply with paragraph 3.B.2.
Inside the helicopter, comply with paragraph 3.B.3.
3.B.2. Installation of self-gripping tapes outside the helicopter (Figure 2)
NOTE 1
The photo in Figure 2 is given as an example in order to
illustrate the installation of self-gripping tapes on a helicopter
equipped with extraction tapes with press-studs.
- If necessary, unbutton the press-stud using a tool (e.g. screwdriver).
- Replace press-stud male part (b) with a new press-stud male part (2),
or
- Interchange press-stud male part (b) with a press-stud male part of a window that is not identified by a color
surround.
- Check for correct buttoning/unbuttoning of extraction tape (a) with the press-stud male part installed on the
window identified by a color surround (see Figure 1).
- If the press-stud can be unbuttoned without excessive effort, no further action is required on this press-stud.
- If the press-stud cannot be unbuttoned or is difficult to unbutton:
. Prepare two self-gripping tapes (3) and (4):
- Adjust the length and width of self-gripping tape (4) with respect to extraction tape (a), as shown in
Figure 2.
- Cut self-gripping tape (3) to length so as to fully cover self-gripping tape (4) when installing tapes (4)
and (3).
. Bond self-gripping tape (4) to extraction tape (a) (Figure 2) as per MTC Work Card 20.03.04.406.
Staple self-gripping tape (4) to extraction tape (a) using a stapler.
. Bond self-gripping tape (3) to the helicopter structure (Figure 2) as per MTC Work Card 20.03.04.406.
Revision 0 2015-08-10  Page 8/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
NOTE 2
It is permitted to reverse the bonding of the self-gripping
tape loop part (4) and the self-gripping tape hook part (3).
CAUTION
ONCE THE  EXTRACTION TAPE HAS  BEEN
ATTACHED TO THE STRUCTURE, DO NOT TOUCH
THE TAPE ANY MORE, IN ORDER TO COMPLY
WITH THE DRYING TIME OF THE SELF-ADHESIVE
FACES.
. Attach extraction tape (a) equipped with the press-stud (female part) to the structure using self-gripping
tapes (3) and (4) (Figure 2).
NOTE 3
Attaching the extraction tape to the structure prevents
premature wear and interference noises generated by
contact between the press-stud and the structure.
- For the window not identified by a color surround, check for correct buttoning/unbuttoning of the tape
equipped with the press-stud male part previously interchanged:
. If the press-stud cannot be unbuttoned or is difficult to unbutton, leave it buttoned until paragraph 3.D.
has been complied with.
3.B.3. Installation of self-gripping tapes inside the helicopter (Figure 3)
NOTE 4
The photos in Figure 3 are given as examples in order to
illustrate the installation of self-gripping tapes on a helicopter
equipped with extraction tapes with press-studs.
- If necessary, unbutton the press-stud using a tool (e.g. screwdriver).
- Prepare two self-gripping tapes (5) and (6):
. Adjust the length and width of self-gripping tape (5) with respect to extraction tape (c), as shown in
Figure 3.
. Cut self-gripping tape (6) to length so as to fully cover self-gripping tape (5) when installing tapes (5) and
(6).
- For helicopters on which the press-stud male part is installed on the trimming:
. Bond self-gripping tape (6) next to press-stud male part (d) (Figure 3) as per MTC Work
Card 20.03.04.406.
- For helicopters on which the press-stud male part is installed on the window:
. Bond self-gripping tape (6) to the trimming (Figure 3) as per MTC Work Card 20.03.04.406.
- Bond self-gripping tape (5) to extraction tape (c) and press-stud female part as per MTC Work
Card 20.03.04.406.
- Staple self-gripping tape (5) to extraction tape (c) using a stapler.
NOTE 5
It is permitted to reverse the bonding of the self-gripping
tape loop part (6) and the self-gripping tape hook part (5).
Revision 0 2015-08-10  Page 9/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
CAUTION
ONCE  • THE  EXTRACTION TAPE HAS  BEEN
ATTACHED TO THE TRIMMING, DO NOT TOUCH
THE TAPE ANY MORE, IN ORDER TO COMPLY
WITH THE DRYING TIME OF THE SELF-ADHESIVE
FACES.
- Attach extraction tape (c) to the helicopter trimming using self-gripping tapes (5) and (6).
3.B.4. Replacement of the press-stud outside the helicopter (Figure 2)
- Remove the self-gripping tapes previously installed.
- Remove press-stud male part (b) (Figure 2).
- Install the new press-stud male part (2).
- Check for correct buttoning/unbuttoning of extraction tape (a) on press-stud male part (2).
- If the press-stud can be unbuttoned without excessive effort, no further action is required on this press-stud
- If the press-stud cannot be unbuttoned or is difficult to unbutton:
• If necessary, unbutton the press-stud using a tool (e.g. screwdriver).
. Check for correct buttoning/unbuttoning of a new extraction tape (1) with press-stud male part (2) prior
to installation:
- If necessary, replace extraction tape (1) with another extraction tape (1).
. Pull extraction tape (a) in order to remove key (e) from extrusion (f).
Make sure that extrusion (f) and key (e) are in correct condition:
- If necessary, discard and replace extrusion (f) and/or key (e) as per Sub-task 56-20-00-422-001 of
AMM Task 56-20-00-062 or Sub-task 56-30-00-422-001 of AMM Task 56-30-00-062 or
Sub-task 56-30-00-424-001 of AMM Task 56-30-00-064.
. Remove extraction tape  ) from key (e).
Install extraction tape (1) on the key.
. Install the key on the extrusion in accordance with the instructions given in Sub-task 56-20-00-422-001
of AMM Task 56-20-00-062 or Sub-task 56-30-00-422-001 of AMM Task 56-30-00-062 or
Sub-task 56-30-00-424-001 of AMM Task 56-30-00-064.
. Button extraction tape (1) on the window equipped with press-stud male part (2).
3.B.5. Replacement of the press-stud inside the helicopter (Figure 3)
- Remove the self-gripping tapes previously installed.
- Remove press-stud male part (d) (Figure 3).
- Install the new press-stud male part (2).
- For helicopters on which the press-stud male part (2) is installed on the trimming:
. Position the trimming inside the helicopter.
- Check for correct buttoning/unbuttoning of extraction tape (c) on press-stud male part (2).
- If the press-stud can be unbuttoned without excessive effort, no further action is required on this press-stud
- If the press-stud still cannot be unbuttoned or is difficult to unbutton:
. If necessary, unbutton the press-stud using a tool (e.g. screwdriver).
. Check for correct buttoning/unbuttoning of a new extraction tape (1) with press-stud male part (2) prior
to installation:
- If necessary, replace new extraction tape (1) with another extraction tape (1).
. Pull extraction tape (c) in order to remove key (h) from extrusion (k).
Revision 0 2015-08-10  Page 10/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
. Make sure that extrusion (k) and key (h) are in correct condition:
- If necessary, discard and replace extrusion (k) and/or key (h) as per Sub-task 56-20-00-422-001 of
AMM Task 56-20-00-062 or Sub-task 56-30-00-422-001 of AMM Task 56-30-00-062 or
Sub-task 56-30-00-424-001 of AMM Task 56-30-00-064.
• Remove extraction tape (c) from key (h).
Install extraction tape (1) on the key.
• Install the key on the extrusion in accordance with the instructions given in Sub-task 56-20-00-422-001
of AMM Task 56-20-00-062 or Sub-task 56-30-00-422-001 of AMM Task 56-30-00-062 or
Sub-task 56-30-00-424-001 of AMM Task 56-30-00-064.
. Button extraction tape (1) on the window or trimming (depending on the helicopter configuration)
equipped with press-stud male part (2).
NOTE 6
Only the press-stud installed on the helicopter trimming is
shown in Figure 3. Perform the same work steps for a press-
stud installed on the window.
3.C. COMPLIANCE CONFIRMATION
Compliance with this document:
Record compliance with this ALERT SERVICE BULLETIN, with its revision number, in the helicopter
documents.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
If difficulties are encountered when buttoning/unbuttoning the tape of a window not identified by a color
surround, replace it as part of a future scheduled inspection.
NOTE 7
The tapes have been installed on these windows (outside
the cabin) to facilitate their maintenance.
Revision 0 2015-08-10  Page 11/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
O N
Figure 2: Installation of self-gripping tapes outside the helicopter
Revision 0 2015-08-10  Page 12/13
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC155-56A006
On soft trimmings  On rigid trim panels
k
5
2
6 —
NOTE
Only the press-stud installed on the helicopter trimming is
shown. For a press-stud installed on the window, comply
with paragraphs 3.B.3. and 3.B.5. by carrying out the same
work steps.
Figure 3: Installation of self-gripping tapes inside the helicopter
Revision 0 2015-08-10  Page 13/13
This document is available on the internet: www.airbushelicopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
