# Airbus Helicopters Alert Service Bulletin EC225-52A017

## Copies (3)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 2 ("Airbus Helicopters ASB EC225-52A017 Revision 2"), 38 pages: PDF https://openairdocs.org/files/sha256/03/a3/03a31cd833d8b59652a344f86881a3f8d46442be79920d364a60e18902dd91cb; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-52a017/file/03a31cd833d8.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0785, the docket of AD 2021-19-16. Not covered by OpenAirDocs’ CC0 dedication.
- Revision 1 ("Airbus Helicopters ASB EC225-52A017 Revision 1"), 36 pages: PDF https://openairdocs.org/files/sha256/80/e5/80e5805e1a7d4d93e9752077a94c82bcbe1af3dcb1337986541ad2d022ec10bb; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-52a017/file/80e5805e1a7d.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0785, the docket of AD 2021-19-16. Not covered by OpenAirDocs’ CC0 dedication.
- No revision named ("Airbus Helicopters ASB EC225-52A017 Revision 0"), 33 pages: PDF https://openairdocs.org/files/sha256/da/b5/dab52c372f8e9400a1afa1015f7696b944041cced7f3ef97c3e757fdcaed65d3; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-52a017/file/dab52c372f8e.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0785, the docket of AD 2021-19-16. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-52A017
- Latest revision known: EC225-52A017, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-52a017

## Text (38 pages)

Revision 2, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0785, the docket of AD 2021-19-16. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
Civil version: LP
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
DOORS - Side stairway door
Improvement of the locking system
Corresponds to modification 0728281
For the attention of
Revision No.  Date of issue
Revision 0  2017-08-29
Revision 1  2019-10-15
Revision 2  2020-02-25
Summary:
The purpose of this ALERT SERVICE BULLETIN is to improve the locking system of the LH side stairway door to
make sure that the door is correctly shut and locked. A direct display unit has also been added to allow the
operator to visually check the locking.
Reason for last revision:
The purpose of revision 2 of this ALERT SERVICE BULLETIN is to correct the references to paragraphs indicated
in paragraph 1.E.2. (Compliance in service), to update the part number of the customized door handle and to install
a spring pin with a larger diameter when installing the direct display unit.
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
ASB EC225 52A017
Revision 0 2017-08-29  Page 1/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
1. PLANNING INFORMATION
• CAUTION
THIS ALERT SERVICE BULLETIN IS WRITTEN
BASED ON THE ORIGINAL HELICOPTER
CONFIGURATION (AS DEFINED IN  • THE
INDIVIDUAL INSPECTION LOG BOOK (RIC)). IT
ALSO TAKES INTO ACCOUNT ALL AIRBUS
HELICOPTERS  APPROVED CONFIGURATION
CHANGES MADE AFTER DELIVERY, IF AIRBUS
HELICOPTERS WAS INFORMED OF THEM. IT IS
THE RESPONSIBILITY OF THE OPERATOR TO
CHECK  THE  COMPATIBILITY OF ANY
MODIFICATIONS  WITH  THE  CURRENT
HELICOPTER  CONFIGURATION.
MODIFICATIONS ARE INCOMPATIBLE,  IT IS THE
RESPONSIBILITY OF THE OPERATOR TO DEFINE
THE NECESSARY ADAPTATION WORK AND HAVE
THEM APPROVED BY THE AIR TRANSPORT
AUTHORITIES IN THE COUNTRY CONCERNED,
AND  TO  MAKE  SURE  THAT  THEIR
AIRWORTHINESS IS FOLLOWED UP.
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters equipped with the LH side stairway door assy PRE MOD 0728281(VIP door locking
improvement).
NOTE 1
Refer to the Individual Inspection Record (or RIC AMS), the
Equipment Log Card (FM) of the side stairway door and the
Aircraft Log Book to identity the current modification status
of the helicopter.
1.A.2. Non-installed equipment or parts
Side stairway door assy PRE MOD 0728281.
NOTE 2
Refer to the Log Card (FM) of the side stairway door and the
Aircraft Log Book to identify the current modification status
of the helicopter.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
Revision 0 2017-08-29  Page 2/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
1.C.  REASON
During an AS532 flight, the amber "DOOR" indicator light came on. Shortly afterwards, the LH side stairway
door opened in flight, tearing off its attachment fittings. The door remained attached to the helicopter by the
load compensator system cable. The helicopter landed without further consequences.
The door handles were in the closed position but the locking of the door was not secured by the internal claw
engagement system of the lock, due to the presence of paint preventing handle return. In-flight vibrations led
to the opening of the LH side stairway door.
Revision 0:
The purpose of this ALERT SERVICE BULLETIN is to improve the locking system of the LH side stairway
door to make sure that the door is correctly shut and locked. A direct display unit has also been added to
allow the operator to visually check the locking.
The purpose of this ALERT SERVICE BULLETIN supersedes the instructions of ALERT SERVICE
BULLETIN No. 52A014 (Check for correct locking of the side stairway door).
Revision 1:
The purpose of revision 1 of this ALERT SERVICE BULLETIN is to update the kits for harmonization of the
stairway door lock (1), and to update the P/N of the spring pin (23) and the countersunk screw (17) and to
extend the compliance in service limit from 24 to 30 months.
Revision 1 affects compliance with revision 0 of this ALERT SERVICE BULLETIN.
Revision 2:
The purpose of revision 2 of this ALERT SERVICE BULLETIN is to correct the references to paragraphs
indicated in paragraph 1.E.2. (Compliance in service), to update the part number of the customized door
handle and to install a spring pin with a larger diameter when installing the direct display unit.
Revision 2 affects compliance with the previous revisions of this ALERT SERVICE BULLETIN.
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
- Removing the LH side stairway door.
- Removing the handle assy.
- Removing the lock control lever.
- Modifying the stop support box.
- Installing a locking visualization system (Helicopters PRE MOD 0726391 only).
- Installing a new handle assy (see NOTE 4 of paragraph 2.C.).
- Installing the LH side stairway door.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Airbus Helicopters recommends compliance with instructions given in paragraph 3.B. of this ALERT
SERVICE BULLETIN, as per operational operational and contractual constraints.
Revision 0 2017-08-29  Page 3/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
1.E.2. Compliance in service
The work must be performed on the helicopter and on non-installed equipment by the operator.
Helicopters/installed equipment or parts:
For helicopters PRE MOD 0726391 (VIP door closing immediate warning), comply with paragraph 3. within
30 months, following receipt of this ALERT SERVICE BULLETIN Revision 0 issued on the date mentioned in
page footer.
For helicopters POST MOD 0726391 (VIP door closing immediate warning), comply with paragraph 3.
except paragraphs 3.B.2.b., 3.B.2.c. and 3.B.2.d. within 30 months, following receipt of this ALERT
SERVICE BULLETIN Revision O issued on the date mentioned in page footer.
Helicopters which have complied with revision 0 or revision 1:
Comply with paragraph 3.B.2.g. of this ALERT SERVICE BULLETIN.
Helicopters which have not complied with revision 0 or revision 1:
Comply with paragraph 3.B. of this ALERT SERVICE BULLETIN except paragraph 3.B.2.g.
Non-installed equipment or parts:
Modify stock as per paragraph 3.B.5. before installation or at the latest within 30 months following receipt of
this ALERT SERVICE BULLETIN revision 0 issued on the date indicated in the page footer.
1.F. APPROVAL
Approval of modifications:
The information or instructions relate to modification 0728281 which was approved
on October 11, 2016 under the authority of EASA Design Organization Approval No. 21J.700 for helicopters
of civil versions subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on August 29, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for helicopters of
civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on August 29, 2017 under the prerogatives of the recognition of design capability FRA21J-002-DGA for
French Government helicopters.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on October 14, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for helicopters
of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on October 14, 2019 under the prerogatives of the recognition of design capability FRA21J-002-DGA for
French Government helicopters.
Revision 0 2017-08-29  Page 4/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbu  elicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved
on February 24, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil
version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved
on February 24, 2020 under the prerogatives of the recognition of design capability FRA21J-002-DGA for
French Government helicopters.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following
personnel qualifications:
Qualifications:
- 1 Mechanical Technician.
- 1 Airframe Technician.
The Estimated Man-hours is indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours
- 6 hours for the Mechanical Technician.
- 2 hours for the Airframe Technician.
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter
configuration.
Helicopter downtime is estimated at one day.
1.H. WEIGHT AND BALANCE
The changes in weight and moment are negligible.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1 K. REFERENCES
The following documents are necessary for compliance with this ALERT SERVICE BULLETIN
Aircraft Maintenance Manual (MMA):
MMA: 52-13-01-061: Removal-Installation - Side stairway door.
Revision 0 2017-08-29  Page 5/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
Standard Practices Manual (MTC):
MTC: 20-02-05-404:  Assembly by screws and nuts - Joining
MTC: 20-02-06-404: Safetying with cotter pins - Safetying and locking assemblies
MTC: 20-02-06-409:  Safetying with Loctite compound - Safetying and locking
MTC: 20-04-01-102:  Use of cleaning products on individual parts and on helicopters - Cleaning
MTC: 20-04-04-403:  Touch-up of the Alodine 1200 protection (Bonderite M-Cr 1200) - Surface treatment
before painting
MTC: 20-04-05-402:  Application of Epoxy primer P05 - P20 - Paint and primer application procedure
MTC: 20-04-05-422:  Application of polyurethane finish paint (1500-M) - Paint and primer application
MTC: 20-05-01-212:  Implementation of Sealing compound CM 6232 - General sealing procedures
MTC: 20-07-03-406:  Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions
MTC: 20-08-05-101:  Drafting and updating the log card (F.M) - General rules applicable to aircraft
MTC: 20-08-05-103:  Monitoring of parts in operation - marking - service life customization - General rules
applicable to aircraft
1.L. OTHER AFFECTED PUBLICATIONS
CAUTION
TO  COMPLY WITH THIS ALERT SERVICE
BULLETIN, THE OPERATOR MUST MAKE SURE
THAT ALL THE MAINTENANCE DOCUMENTS
REQUIRED FOR THE MAINTENANCE OF THIS
INSTALLATION ARE AVAILABLE. IF NOT, IT IS
THE OPERATOR'S RESPONSIBILITY TO OBTAIN
THE DOCUMENTS FROM THE USUAL AIRBUS
HELICOPTERS CONTACT.
This modification will be integrated into the following manual:
Aircraft Maintenance Manual (MMA).
Revision of the documents Illustrated Parts Catalog (IPC) will be updated on the customer's order.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
PRE MOD and POST MOD side stairway doors are not interchangeable.
Mixability:
Not applicable.
Revision 0 2017-08-29  Page 6/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For any information on the price of modification kits and/or components or for assistance, contact the Airbus
Helicopters Network Sales and Customer Relations Department.
Availability
Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's
request.
Procurement
Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Kits to be ordered for one helicopter or one assembly:
For helicopters PRE MOD 0726391 and which have not complied with revision 0 of this ALERT SERVICE
BULLETIN:
Order, as required, one kit 332A08-1666-0572 and one kit 332A08-0907-0273.
For helicopters POST MOD 0726391 and which have not complied with revision 0 of this ALERT SERVICE
BULLETIN:
Order, as required, one kit 332A08-1666-0572 only.
Order the components as per NOTE 3, NOTE 4 and NOTE 5 for each helicopter which has complied with
revision 0 or for each stairway door assy P/N 330A22-2400-06.
Revision 0 2017-08-29  Page 7/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
New  Old
Key Word  Qty  PIN  Item  P/N  Instruction
VIP door locking
improvement kit,  332A08-1666-0572
including:
Handle, outer  330A22-2443-21  2  330A22-2443-20  Scrap
Cover, upper  332A22-0332-20  3
Cover, lower  332A22-0333-20  4
Support, spring  332A22-0330-20  5
Spring  330A22-2494-20  6
Shim  1  330A22-2411-46  7
Ring, retaining  1  23201AM0160T
Washer  5  23111AG050LE  9
Screw  5  22271BC050014L  10
Nut  2  ASN52320BH050N  24
Pin, spring  З  NSA5319-05-025  43
New  Ite  Old
Key Word  Qty  P/N  m  P/N  Instruction
VIP door closing direct
visualization kit,  332A08-0907-0273
including:
Plexiglass  332A22-0326-20  11
Window, visualization  332A22-0326-01  12
Blanking cap, fixed  332A22-0326-02  13
Lever, control, pennant  332A22-0326-03  14
door
Shim, adjustment  332A22-0326-22  15
Flame assy  1  332A22-0326-04  16
Screw, 100Countersunk  2  22256BC040010L  17
Head
Bolt, hexagonal head  2  22208BC040014L  18
Bolt, special wide head  A0164TK040S010X  19
Nut, self-locking  6  ASN52320BH040N  20
Washer  23111AG040LE
washer, flat  2  23112AG04OLE  22
Nut, self-locking  1  ASN52320BH050N  24
Pin, spring  2  NSA5319-05-025  43
Revision 0 2017-08-29  Page 8/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
Equipment or parts to be ordered separately:
New  Old
Key Word  Qty  P/N  Item  P/N  Instruction
including:  Stairway door lock  330A22-2442-01  1  330A22-2442-00  Scrap  See NOTE 3
Handle, interior  ref  For reference only  1a  For ref. only
Pins  ref  For reference only  1b  For ref. only
Cover  ref  For reference only  1c  For ref. only
Screw  ref  For reference only  1d  For ref. only
Spring  ref  For reference only  1e  For ret. only
Lever  ref  For reference only  1f  For ref. only
Axle  ref  For reference only  1g  For ref. only
Screw, pressure  ref  For reference only  1h  For ref. only
Lock, cylinder  ref  For reference only  1j  For ref. only
Box  ref  For reference only  1k  For ref. only
Countersunk screw  2  22256BC040010L  17  See NOTE 5
Pin, spring  2  NSA5319-05-025  43  See NOTE 5
Customized handle  330A22-2491-2351  45  See NOTE 3
and NOTE 4
NOTE 3
When ordering the stairway door lock (1): If the interior
handle has a chrome finish, order P/N 330A22-2442-01 (1).
If the interior handle has a customized finish, order
P/N 330A22-2442-01 (1) + the customized handle
P/N 330A22-2491-2351 (45) and indicate the finish specified
in the customer file when ordering.
NOTE 4
For the attention of customers with a customized handle (45)
delivery lead times will be indicated by the Sales and
Customer Relations Department on the customer's order.
NOTE 5
For helicopters which have complied with this ALERT
SERVICE BULLETIN revision 0 with kits 332A08-1666-0571
and 332A08-0907-0271.
Order the screws (17) and the spring pins (43) and refer to
paragraph 3.B.2.g.
Revision 0  2017-08-29  Page 9/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
Order components listed below:
New  Old
Key Word  Qty  P/N  Item  P/N  Instruction
Outer label, White (EN)  332A00-0688-AE  35
Outer label, White (FR)  332A00-0688-AF  36
Outer label, White (EN)  332A00-0649-AJ  37
Outer label, White (FR)  1  332A00-0649-AK  38
Consumables to be ordered separately:
As per Work Cards and Tasks indicated in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  P/N  Item
Red paint  AR  ECS2018.40-2801  CM 4185  25
Adhesive, Loctite (242)  AR  ASNA4018  CM 683  26
Sealant (PR1829B2)  AR  ECS6046-1198  CM 6232  27
Chemical transformation agent  AR  ECS2338.10  CM 316  28
EPOXY primer (P05)  AR  DHS186-111.20  CM 487  29
Grease  AR  DCSEA354  CM 115  30
Green paint  AR  ECS2018.40-2455  CM 4186  44
The consumables can be ordered separately from the following companies.
Aviatec global aviation
Website: https://www.aviatec.net
Telephone: +33 1.34.46.45.24 or +49 4193.8803.630
Fax: +33 1.34.46.45.26 or +49 4193.8803.699
AOG: +49 4193.8803.660
AOG email: aog@aviatec.aero
BDSI
Gaches chimie
Website: https://www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
Website: https://www.boeingdistribution.com
Telephone: +1.305.925.2600
Fax: +1.305.507.7191
AOG: +1.305.471.8888
AOG email: AOGdesk@Boeingdistribution.com
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2017-08-29  Page 10/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- As per Work Card 20-02-06-409 (MTC), read and comply with the instructions for safetying with loctite
compound.
- As per Work Card 20-04-04-403 (MTC), read and comply with the instructions for touching-up with Alodine
1200 protection (Bonderite M-Cr 1200).
- As per Work Card 20-04-05-402 (MTC), read and comply with the instructions for applying epoxy primer
P05 - P20
- As per Work Card 20-05-01-212 (MTC), read and comply with the instructions for the implementation of
sealing compound CM 6232.
As per Work Card 20-02-05-404 (MTC), unless specified differently, apply the standard tightening torque
values.
3.B. WORK STEPS
3.B.1. Preliminary steps
- Disconnect all electrical supply sources as per Work Card 20-07-03-406 (MTC).
- Install the appropriate access equipment.
- Remove protective carpet.
- Remove stairway door (a) (Figure 1) as per Task 52-13-01-061 (MMA).
- Remove screws (m), cups (n) and step No. 4 (o) from stairway door (a).
3.B.2. Procedure
3.B.2.a. Replacement of the handle assy (Figure 1, Figure 3 and Figure 5)
As per Figure 1:
- On inside door:
• Remove screw (g), washer (h), nut i) from rod (f) (DETAIL B).
• Disconnect rod (f) from lock (e).
• Remove screw (g), washer (h), nut i) from rod (k).
• Disconnect rod (k) from lock (e).
• Scrap nuts ().
- On outside door:
• Remove and scrap retaining ring (ac) and outer handle (ab) (DETAIL C).
• Remove screws (ad), washers (ae) and lock (e).
• Remove barrel (af) from lock (e).
• Scrap lock (e).
Revision 0 2017-08-29  Page 11/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
As per Figure 3 and Figure 5:
- On lock (1) (DETAIL J Figure 5):
• Remove the two pins (1b) and handle (1a) (SECTION K-K).
• Remove screws (1d) and cover (1c).
• Remove spring (1e).
• Remove pin (1b), lever (1f) and axle (1g).
• On axle (1g), loosen screw (1h) and remove barrel (1)).
• Scrap pins (1b) and store barrel (1j).
- Install barrel (af) on axle (1g), tighten screw (1h) to standard torque.
- Put box (1k) and lower cover (4) in position on stairway door (a) by interlaying sealant (27).
- Attach box (1k) and lower cover (4) with three screws (10) and three washers (9) (DETAIL C Figure 3).
- Put support (5), shim (7) and handle (2) in position on axle (1g) (SECTION K-K Figure 5).
- Align holes (Ø 2 mm) of handle (2), support (5) and shim (7).
CAUTION
SPRING (6) MUST FAVOR THE LOCKING
(CLOCKWISE ROTATION) OF THE MECHANISM
WHEN ACTUATING HANDLE (2).
- Install spring (6) on axle (1g).
NOTE 1
The longer end of spring (6) must be inserted in support (5),
shim (7) and handle (2).
- Install axle (1g) equipped with support (5), shim (7) and spring (6) on box (1k) by inserting the shortest
end of spring (6) in hole T (DETAIL J.
NOTE 2
Make sure that o-ring (1m) is correctly positioned in its
housing before inserting axle (1g).
NOTE 3
Turn axle (1g) with handle (2) in the counterclockwise
direction (spring tensioned) until spring (6) is aligned with
hole T of box (1k).
- Install lever (1f) and a spring pin (43) on axle (1g) (SECTION K-K).
- Install spring (1e) on lever (1f).
- Install cover (1c) by inserting the end of the spring in its orifice.
- Attach cover (1c) with screws (1d) to match box (1k).
- Install handle (1a) or the customized handle (45) and two spring pins (43).
- Apply grease (30) to ball-ends of lever (1f) (DETAIL J).
- Connect rods (f) and (k) (DETAIL B Figure 3) on lever (1f) (DETAIL J Figure 5).
- Install screws (g), washers (h) and nuts (24) (DETAIL B Figure 3).
- Adjust the locking system as per paragraph 4.A.1.a.
- Install retaining ring (8) (DETAIL C Figure 3).
- Put upper cover (3) in position on stairway door (a) by interlaying sealant (27).
- Attach upper cover (3) with three screws (10) and three washers (9) (DETAIL C).
Revision 0 2017-08-29  Page 12/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
3.B.2.b. Removal of the upper lock control lever (Figure 1)
As per Section D-D:
- Remove conical pin (y) and upper lock (x).
- Remove conical pin (y) and upper lock axle (aa) from lock control lever (q).
- Scrap conical pins (y).
- Remove screws (u), washers (v) and lock support (w).
As per Detail B:
- Remove axle (r), washers (s), nut (t) and lock control lever (q) from rod (p).
- Scrap lock control lever (q) and nut (t).
3.B.2.c. Modification of the stop support box (Figure 1 and Figure 2)
As per Detail A, Figure 1:
- Remove screws (c), washers (d) and stop (b) from box (z).
As per Figure 2:
- Cut out box (z) to diameter 34 mm as per Detail I.
- Drill four holes dia. 4.5 mm on box (z).  Do (a) a pen onli
- Drill two holes dia. 4.5 mm on box (z) as per Detail F.
- Countersink at 100° the two holes dia 4.5 mm on box (z).
- Cut out the riser No. 4 of door (a) as per Detail G.
- Cut out the coating of door (a) as per Detail H.
- Deburr and protect with chemical transformation agent (28) and primer (29) the modified areas of box
(z) and door (a).
3.B.2.d. Installation of the locking visualization system (Figure 3 and Figure 4) (PRE MOD 0726391 only)
- Apply red paint (25) to upper lock (x) as per Work Card 20-04-05-422 (MTC) and Detail I of Figure 4.
- Install glass (11), window (12), screws (19), washers (21) and nuts (20) (DETAIL G).
- Seal glass (11) with sealant (27).
- Install fixed blanking cap (13), screws (17), washers (21) and nuts (20).
- Install stop (b), screws (c) and washers (d) on box (z) (DETAIL E).
- Adjust the visualization system as per paragraph 4.A. 1.b.  NO ATE SECTION DEAN 23)
- Perform the marking as per paragraph 4.A. 1.c.
- Install lock support (w), screws (u) and washers (v) (SECTION D-D Figure 3).
- Install upper lock (x) on axle (aa) (DETAIL F Figure 4).
- Counter drill the hole (A) to the diameter of 3mm.
- Install spring pins (43) on upper lock (x).
- Put axle (aa) in position in lock support (w).
- Assemble lever (14), shim (15) and flame assy (16) with screws (18) and washers (22) (DETAIL H
Figure 4).
- Put the assembly in position on axle (aa) (DETAIL F Figure 4).
- Check the adjustment of shim (15) and flame assy (16).
NOTE 4
Flame assy (16) and axle (aa) must be correctly centered
and rotation must be frictionless.
Revision 0 2017-08-29  Page 13/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
CAUTION
FLAME ASSY (16) AND FIXED BLANKING CAP
(13) ARE ADJUSTED AND ATTACHED SUCH
THAT WHENEVER THE LOCK IS CLOSED, ONLY
THE GREEN COLOR MUST BE VISIBLE. THE
RED  COLOR MUST APPEAR AT  • THE
SLIGHTEST MOTION OF THE LOCKS WARNING
ABOUT THE DANGER THAT REPRESENTS THE
OPEN DOOR.
- Check the position of flame assy (16) and fixed blanking cap (13).
- Remove screws (18) one by one and install them by applying loctite adhesive (26) (DETAIL H).
- Install lever (14), shim (15) and flame assy (16) on axle (aa) (DETAIL F).
- Counter drill the hole (A) to the diameter of 3mm.
- Install spring pin (43) on lever (14).
- Apply grease (30) to ball-end of lever (14).
- Connect rod (p) to lever assy (14), shim (15) and flame assy (16): screw (r), washer (s), nut (24)
(DETAIL B Figure 3).
3.B.2.e. Modification of the door marking (Figure 6 and Figure 7)
- Identify the door areas where labels will be bonded as per Figure 6 and Figure 7.
- Clean these areas as per Work Card 20-04-01-102 (MTC).
- Bond label (35) or (36) to the external face of the door as per helicopter configuration and Figure 6.
- Bond label (37) or (38) to the internal face of the door as per helicopter configuration and Figure 7.
3.B.2.f.  Identification of the door
- Modify door P/N as per paragraph 3.C.
- Create the log card (FM) of the stairway door P/N 330A22-2400-06 as per Work Card
20-08-05-101 (MTC).
3.B.2.g. Check of the screw and the pin (Figure 4 and Figure 8)
As per Figure 4 and Figure 8
- Remove and keep the stairway step (ab) to facilitate access (Figure 8, Detail B).
- Make sure that the P/N of the screws (17) is correct (22256BC040010L):
. as per paragraph 4.B. and installation as per Figure 4 (Detail G),
. and by inspecting to make sure that at least 2 threads protrude (not including rounding or chamfered
terminal). The use of an endoscope is recommended.
- Make sure that the P/N of the spring pins (43) is correct (NSA5319-05-025) as per paragraph 4.B and
installation as per Figure 4 (Detail F).
- If necessary, counter drill the holes (A) to diameter of 3mm to install spring pins (43) to be compliant
with the P/Nos. above and/or replace the existing screws (17).
- Install the stairway step (ab) (Figure 8, Detail B).
3.B.3. Tests
- Install stairway door (a) (Figure 3) as per Task 52-13-01-061 (MMA).
• Close and lock stairway door (a).
- Check the locking mechanism of the door as per paragraph 4.A.2.a.
- Check the travel as per paragraph 4.A.2. b.
- Check the handle kinematics as per paragraph 4.A.2.c.
Revision 0 2017-08-29  Page 14/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
3.B.4. Final steps
- Open stairway door (a) (Figure 1).
- Install step No. 4 (o) on stairway door: screw (m), cups (n).
- Install protective carpet.
- Close stairway door (a).
- Remove the access means.
- Connect all electrical supply sources as per Work Card 20-07-03-406 (MTC).
3.B.5. Work steps for non-installed equipment or parts
- Modify stock of side stairway door P/N 330A22-2400-0502 as per paragraph 3.B.2. before installation on
- Scrap stock of outer handle P/N 330A22-2443-20.  1 302243-20.
- Scrap stock of lock P/N 330A22-2442-00.
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record full compliance with this ALERT SERVICE BULLETIN with the revision number in the helicopter
documents.
- Record full compliance with this ALERT SERVICE BULLETIN with the revision number in the log card (FM)
of the stairway door P/N 330A22-2400-06 as per Work Card 20-08-05-101 (MTC).
- Please confirm compliance with this ALERT SERVICE BULLETIN:
QR-Code or hypertext link
NOTE 5
The recording of compliance with ALERT SERVICE
BULLETINS in the R-Tex tool does not replace the
recording in the helicopter documents.
ASB EC225 52A017
Tracking of modifications in the documentation:
Record full embodiment of modification 0728281 in the helicopter documents.
Identification of modifications on equipment or parts:
Identify parts / assemblies as per table below and/or as per Work Card 20-08-05-103 (MTC):
Key Word  Old P/N  New P/N  MOD  Marking type
Lateral  330A22-2400-0502  330A22-2400-06  MOD 0728281  Indelible ink
stairway door
Revision 0  2017-08-29  Page 15/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
The Aircraft Maintenance Manual (MMA) will integrate these locking mechanism check and adjustment
instructions (Appendices 4.A.) during a further revision. When these instructions are integrated, refer to this
manual.
Revision 0 2017-08-29  Page 16/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2017-08-29  Page 17/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PRE MOD  FWD
KD
E (SEE FIGURE 2)
в Д
SECTION
D-D
ad
ae
af
ac
Ext.
ab
Int.  Ext.
Return to paragraphs 3.B.1./ 3.B.2.a./ 3.B.2.b / 3.B.2.c and 3.B.4.
Figure 1
Revision 0  2017-08-29  Page 18/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2017-08-29  Page 19/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
(SEE FIGURE 1)
F
COLOS
J-J
G
Return to paragraph 3.B.2.c.
Figure 2
Revision 0 2017-08-29  Page 20/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 21 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2017-08-29  Page 21/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 22 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
POST MOD
SECTION  в[)
D-D
(SEE FIGURE 4) EY
(SEE FIGURE 5)
(SEE FIGURE 4)
Ext.  Int.
= Кк
(SEE FIGURE 5)
Return to paragraph 3.B.2.a. / 3.B.2.d. / 3.B.3.
Figure 3
Revision 0  2017-08-29  Page 22/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 23 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2017-08-29  Page 23/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 24 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
(SEE FIGURE 3)  FWD
- 13
22
18
CM683  - 122
19
20
21
Return to paragraph 3.B.2.d. / 3.B.2.g.
Figure 4
Revision 0  2017-08-29  Page 24/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 25 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2017-08-29  Page 25/38
Revision 2  2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 26 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
J
Л
30
CM115
1†
SECTION
K-K
• 1k  1a or 45
8
1j
af
EXT.  INT.
1b
1g  1h  3/4  1m  1d  43
Return to paragraph 3.B.2.a.
Figure 5
Revision 0 2017-08-29  Page 26/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbu  elicopters.com/techpub/

### Page 27 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
STAIRWAY DOOR
SEE FROM OUTSIDE
35
36
HANDLE
AFTER CLOSING
CHECK NO  OR
HANDLE ROTATION
VERIFIER LA NON
ROTATION DE LA
POIGNEE APRES
FERMETURE
35
36
Return to paragraph 3.B.2.e.
Figure 6
Revision 0 2017-08-29  Page 27/38
Revision 2 2020-02-25  This document is available on the Internet: www.ai  elicopters.com/techpub/

### Page 28 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
38  STAIRWAY DOOR
37  SEE FROM INSIDE
30_
AFTER CLOSING CHECK
— 37
NO HANDLE ROTATION
AND GREEN MARKS ALIGNMENT
OR
VERIFIER LA NON ROTATION DE
LA POIGNEE ET L'ALIGNEMENT DES  — 38
MARQUEURS VERT APRES FERMETURE
Return to paragraph 3.B.2.e.
Figure 7
Revision 0 2017-08-29  Page 28/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 29 (OCR)

→ AIRBUS
HELICOPTERS  ASB No. EC225-52A017
ва
ab
Return to paragraph 3.B.2.g.
Figure 8
Revision 0 2017-08-29  Page 29/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 30 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4. APPENDIX
4.A. ADJUSTMENT OF THE LOCKING MECHANISM
During the adjustment phases, the locking mechanism must be in the "closed-locked door" position.
4.A.1. Adjustment of the stairway door locking mechanism
4.A. 1.a.  External adjustment
The external adjustment must be performed in compliance with paragraph 3.B.2.a.
4.A.1.a.1. Adjustment of the visual indicator in translational direction along Y axis
- The adjustment of the visual indicators is performed using a circular peel shim. This shim is used to
adjust the spring support.
- Delaminate shim until the green visual indicator is in the correct position through the upper and lower
tairing ports.
FAIRING
OUTER HANDLE
SHIM
SPRING SUPPORT
VISUAL INDICATOR
TRANSLATIONAL DIRECTION
OF VISUAL INDICATOR
Adjustment of the external visual indicator
CRITERION: In the closed and locked position, no red mark must be visible.
Revision 0 2017-08-29  Page 30/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbus  elicopters.com/techpub/

### Page 31 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.1.a.2. Adjustment of the visual indicator in rotational direction along Y axis
- The adjustment of the visual indicators in rotational direction is performed through paint touch-up
using paints (25) and (44) as per Work Card 20-04-05-422 (MTC).
- Apply touch-up on the spring support.
APPLY PAINT
TOUCH-UP
ROTATIONAL
DIRECTION OF
VISUAL INDICATOR
VISUAL INDICATOR
CRITERION: In the closed and locked position, no red mark must be visible on either side of the
ports (LH and RH).
Revision 0 2017-08-29  Page 31/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 32 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.1.b. Internal adjustment
The internal adjustment must be performed in compliance with paragraph 3.B.2.d.
- The drive square must be drilled in accordance with the hub and the handle to the given dimensions.
- Make sure the engagement of pins (A, B and C) in the drive square then evaluate the distance by
gauging on either side of drillings.
- The engagement for pins B and C is identical. See VIEW AS PER DETAIL 1 for assembly details.
DETAIL 1
Pin assembly
CRITERION: The clearance for pin engagement must be 1.5 mm (.059 in) max. for pins A, B and C
(see Detail 1).
Revision 0 2017-08-29  Page 32/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 33 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
View as per Detail 1
(46.5)
(40.5)  HANDLE
(2.5)
CLEARANCE 1.5 mm (.059 in)
HUB
AAAAAL
PINS B AND C
PIN A
CLEARANCE 1.5 mm (.059 in)
DRIVE SQUARE
LEVER  CLEARANCE 0.5 mm (.019 in)
COVER
Pinning of handle and hub
TYPICAL SECTION A-A describes the max. clearance to be checked during pin assembly. This section is
valid for all the system pins.
TYPICAL SECTION A-A
CLEARANCE 1.5 mm (.059 in)  PIN A
CLEARANCE 1.5 mm (.059 in)
Pinning of handle and hub
Revision 0 2017-08-29  Page 33/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbu  elicopters.com/techpub/

### Page 34 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.1.c. Inside marking
The inside marking must be performed in compliance with paragraph 3.B.2.d.
- Once the adjustment has been performed, do the green marking on the cover and lever as per
Work Card 20-04-05-422 (MTC).
The slightest translational or rotational mechanism motion must enable the marking misalignment.
COVER  LEVER
Marking after adjustment of cover and lever
CRITERION: the green marks after adjustment must be aligned at ‡ 0.1 mm (.0039 in)
- The position of the red visual indicator is the result of the previous adjustments. The red visual indicator
must come on when the mechanism is in translational motion.
- If the red visual indicator is visible in the "closed and locked door" position, apply a finish paint touch-up.
- If the red visual indicator is not visible in the "closed and unlocked door" position, apply a finish paint
(25) touch-up as per Work Card 20-04-05-422 (MTC).
Ф27.4 МАХ
COVER
INNER HANDLE  CLEARANCE 0.5 mm  (.019 in)
Check of the red visual indicator
CRITERION: When the green marks are aligned, the maximum tolerated clearance between inner
handle and cover must be 0.5 mm (.019 in). The red visual indicator must not be visible.
Revision 0  2017-08-29  Page 34/38
Revision 2 2020-02-25  This document is available on the Internet: www.a  icopters.com/techpub/

### Page 35 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.2. Check
4.A.2.a. Check of the locking mechanism
4.A.2.a.1. Check of the inside marking
"Closed-locked door" position  "Closed-unlocked door" position
Visual checks of the locking mechanism closing (inner handle)
CRITERIA:
- When the mechanism is in the "closed and locked door" position, the green visual indicators
must be aligned (1).
- When the mechanism is in the "closed and unlocked door" position, the green visual indicators
must be misaligned (2).
- When the mechanism is in the "closed and unlocked door" position, the red visual indicator is
visible (3).
Revision 0 2017-08-29  Page 35/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 36 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.2.a.2. Check of the outside marking
"Closed-locked door"  "Closed-unlocked door"  Open position
position  position  (locked/unlocked)
Visual checks of the locking mechanism closing (outer handle)
CRITERIA:
- When the mechanism is in the "closed and locked door" position, only the green visual
indicator must be visible (1).
- When the mechanism is in the "closed and unlocked" position, the green and red visual
indicators must be visible (2).
- When the mechanism is in the "open door" position, only the red visual indicator must be
visible (3).
4.A.2.b. Check of the travel
- The mechanism unlocking travel must not be more than 6 mm (.236 in).
OUTER HANDLE
Mechanism travel
Revision 0 2017-08-29  Page 36/38
Revision 2 2020-02-25  This document is available on the Internet: www.a  elicopters.com/techpub/

### Page 37 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.A.2.c. Check of the handle kinematics
- Once they are installed, the springs must favour the locking of the mechanism when actuating the
handle.
INNER SPRING  OUTER SPRING
Visualization of the springs
Revision 0 2017-08-29  Page 37/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 38 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-52A017
4.B. CHECK OF SCREW (17) AND SPING PIN (43)
Ø 4mm
10mm
Screws (17) P/N 22256BC040010L
25 mm
• 3,3 mm
Pins (43) P/N NSA5319-05-025
Revision 0 2017-08-29  Page 38/38
Revision 2 2020-02-25  This document is available on the Internet: www.airbush  elicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
