# Airbus Helicopters Alert Service Bulletin EC225-53A065

Copy: Revision 4 ("Airbus ASB EC225 53A-065 R4"), 76 pages: PDF https://openairdocs.org/files/sha256/ce/c4/cec410e6955b586e51e86dc7a7f0d5a8f3b9e66c26fa2bb83bd0b2375523ae4e; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-53a065/file/cec410e6955b.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-1736; AD 2025-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-53A065
- Latest revision known: EC225-53A065, Revision 4, dated May 28, 2024 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-53a065

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2025-23-07](https://openairdocs.org/ad/2025-23-07.md), effective Jan 12, 2026: Revision 4

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec225-53a065/proposed.md).

## Text (76 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-1736; AD 2025-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Civil version(s): LP
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
FUSELAGE - Bracket and support assembly
New link of the suspension bar attachment brackets of the Main Gear Box (MGB)
Corresponds to modifications 0728521, 0728904, 0728496 and 0729044
For the attention of
Revision No.  Date de diffusion
Revision 0  2021-08-19
Revision 1  2022-01-06
Revision 2  2022-05-05
Revision 3  2023-06-15
Revision 4  2024-05-28
Summary:
The purpose of this ALERT SERVICE BULLETIN is to improve the link of the MGB suspension bar attachment
brackets.
Reason for last revision:
The purpose of revision 4 of this ALERT SERVICE BULLETIN is to add more details on paragraph 1.E.2.
These details allow to make sure that the right shim and washer are installed according to the configuration of the
helicopter.
Compliance:
It is mandatory to comply with this ALERT SERVICE BULLETIN.
Export Control:
US Export Control - No US content. This Item does not contain any U.S. origin ITAR or EAR content.
FR Export Control - Not Listed. This Item is not listed against the EC regulations in the EU/FR
Revision 0  2021-08-19  Page 1/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 2 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
1.  PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters PRE MOD 0728496.
NOTE 1
Modification 0728496 consists in installing new MGB
suspension bar attachment bracket links on the X3855 and
X5295 frames.
NOTE 2
Refer to the Individual Inspection Log Book (RIC AMS) to
identify the current modification status of the helicopter.
Helicopters which have already complied with former revisions of this ALERT SERVICE BULLETIN are
concerned by revision 3 of this ALERT SERVICE BULLETIN.
For the operators who complied with revision 3 of this ALERT SERVICE BULLETIN, compliance with
revision 4 is not necessary.
1.A.2. Non-installed equipment or parts
Not applicable.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Revision O
A reduction in tightening torque was observed during the tightening torque check on the attachment nuts of
the MGB suspension bar attachment brackets.
Airbus Helicopters implemented a protective measure through ALERT SERVICE BULLETIN No. 04A013,
"Periodic replacement of the Main Gearbox (MGB) suspension bar attachment pins "which consisted in
applying a coefficient to the flight hours of the bracket attachment bolts of the MGB suspension bars.
Airbus Helicopters developed an improvement which consists in installing new links on the attachment
brackets of the MGB suspension bars through the following four modifications, 0728521, 0728904, 0728496
and 0729044.
Table No. 1 takes into account the different existing configurations.
The installation of longer bolts combined with cylindrical bobbins will allow for easier torque tightening and
will improve durability.
In time, the checking time limit for toque tightening will be increased to align with the inspection
at 1320 hours.
The embodiment of this modification will enable the checking interval to be extended for the tightening
torques of this coupling.
Revision O  2021-08-19  Page 2/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 3 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Compliance with this ALERT SERVICE BULLETIN cancels the directives of ALERT SERVICE BULLETIN
No. 04A013 "Periodic replacement of the Main Gearbox (MGB) suspension bar attachment pins ".
Revision 1
The purpose of revision 1 of this ALERT SERVICE BULLETIN is to:
- Change this Service Bulletin in an ALERT SERVICE BULLETIN, mainly because it introduces mandatory
limits (SLL).
- Add updates in the Service Life Limits (SLL).
- Take into account customers feedbacks.
- Delete the paragraph 1.B. because the systematic replacement of the front bracket screws in this
ALERT SERVICE BULLETIN cancels the add-on factors complied through the
ALERT SERVICE BULLETIN No. 04A013.
Revision 1 of this ALERT SERVICE BULLETIN has an effect on the execution of the Revision 0 of this
ALERT SERVICE BULLETIN.
Revision 2
The purpose of revision 2 of this ALERT SERVICE BULLETIN is to update the nominal torque value of
the nuts (9) of the new screw of the forward bracket attachment.
This update has been made as a result of customer's feedback.
Revision 2 of this ALERT SERVICE BULLETIN has no effect on the execution of the previous revisions of
this ALERT SERVICE BULLETIN.
Revision 3
The purpose of revision 3 of this ALERT SERVICE BULLETIN is to take into account the:
- Design modifications: add the MP/N of missing front plate old reference (332A22-1667-22) and renumbered
reference (332A08-1729-67) in chapter 3.C.
- ALS and Working card present in the previous revision integrated in technical publication
- New process tech Data publication: new front plate reference added in the ALS through a dedicated
Delivery Note
- Customer's feedback: update the paragraph 2.C., the procedures and the figures.
The following paragraphs have been deleted because they are now integrated in the documentations:
- Appendix 4.C.: Service Life Limit (SLL) of the front plate and new pins, integrated in the ALS
RN 014 of 2022-06-01
- Appendix 4.D.: Check of tightening torques of the forward and AFT attachment pins, integrated in the ALS
RN 014 of 2022-06-01
- Appendix 4.E.: Procedure to check of tightening torques, integrated in the MMA RN 023 of 2022-06-01 with
the revised Task 53-26-00-212 (MMA).
The new front plate reference is added in the ALS through a dedicated Delivery Note. Refer to the
paragraph 1.L.
Revision 3 of this ALERT SERVICE BULLETIN has an effect on the execution of the previous revisions of
this ALERT SERVICE BULLETIN.
Revision 0  2021-08-19  Page 3/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 4 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Revision 4
The purpose of revision 4 of this ALERT SERVICE BULLETIN is to add more details on paragraph 1.E.2.
These details allow to make sure that the right shim and washer are installed according to the configuration
of the helicopter.
Revision 4 of this ALERT SERVICE BULLETIN has no effect on the execution of the revision 3 of
this ALERT SERVICE BULLETIN.
1.D. DESCRIPTION
Modification 0728521 consists in making a cutout in the X3855 frame to make it possible to install the new
MGB bracket attachment screws.
Modification 0728904 consists in replacing the attachment gussets to the LH and the RH of the 26° beam on
the X5295 frame to avoid interference with the new attachment screw of the MGB brackets.
Modification 0728496 consists in:
- removing the MGB attachment brackets,
- installing the MGB attachment brackets using new bolts, washers, shims, cylindrical bobbins, linings, nuts
and pins,
- Creating a Log Card (FM) to implement a Service Life Limit (SLL) for the front plate.
- Returning the feedback sheet.
Modification 0729044 consists in adding new shims on the LH and the RH sides of the rails of the rear sliding
cowling to avoid interference between the cowling and the new screws of the new links on the attachment
brackets of the MGB suspension bars.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Helicopters/installed equipment or parts:
Airbus Helicopters recommends compliance with the instructions in paragraph 3. of this
ALERT SERVICE BULLETIN as per operational and contractual constraints.
Non-installed equipment or parts:
Not applicable.
1.E.2. Compliance in service
The work must be performed on the helicopter by the operator.
Revision 0  2021-08-19  Page 4/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 5 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Helicopters/installed equipment or parts:
Airbus Helicopters makes it mandatory to comply with the instructions of paragraph 3. of this
ALERT SERVICE BULLETIN, issued on the date indicated in the page footer, within 1320 flight hours or
40 months (the first limit reached is applicable) from receipt of revision 0 of this ALERT SERVICE BULLETIN
as per table No. 1 below:
Table No. 1
Helicopter configuration  Paragraph to comply with
PRE MOD 0728521
Configuration No. 1  PRE MOD 0728904  Comply with paragraph 3.
PRE MOD 0729044
Configuration No. 2  POST MOD 0729044  PRE MOD 0728521  PRE MOD 0728904  Comply with paragraph 3. except for  paragraph 3.B.2.c.
PRE MOD 0728521
Configuration No. 3  POST MOD 0728904  POST MOD 0729044  Comply with paragraph 3. except for  paragraphs 3.B.2.b. and 3.B.2.c.
POST MOD 0728521
Configuration No. 4  POST MOD 0728904  Comply with paragraph 3. except for
PRE MOD 0729044  paragraphs 3.B.2.a. and 3.B.2.b.
PRE MOD 0728521
Configuration No. 5  POST MOD 0728904  Comply with paragraph 3. except for
PRE MOD 0729044  paragraph 3.B.2.b.
POST MOD 0728521
Configuration No. 6  PRE MOD 0728904  Comply with paragraph 3. except for
POST MOD 0729044  paragraphs 3.B.2.a. and 3.B.2.c.
POST MOD 0728521
Configuration No. 7  PRE MOD 0728904  Comply with paragraph 3. except for
PRE MOD 0729044  paragraph 3.B.2.a.
POST MOD 0728521  Comply with paragraph 3. except for
Configuration No. 8  POST MOD 0728904  paragraphs 3.B.2.a., 3.B.2.b. and
POST MOD 0729044  3.B.2.c.
For helicopters which have not complied with the former revisions of this ALERT SERVICE BULLETIN,
comply with paragraph 3.B. of this ALERT SERVICE BULLETIN except paragraphs 3.B.2.c. 1.b. and
3.B.2.C.2.b.
Configurations No. 1, 4, 5 and 7:
For helicopters which have not complied with Revision 3 but complied with at least one of the previous
revisions of this ALERT SERVICE BULLETIN:
- Comply with paragraph 3.B.2.c.1.b. (PRE MOD 0726238) during the next scheduled maintenance
inspection without exceeding 40 months after you received this ALERT SERVICE BULLETIN revision 0.
Or
- Comply with paragraph 3.B.2.c.2.b. (POST MOD 0726238) during the next scheduled maintenance
inspection without exceeding 40 months after you received this ALERT SERVICE BULLETIN revision 0.
NOTE 3
For the helicopters who comply with the previous revisions,
apply the corrected tightening torque on the fixing screws of
the front fitting as shown in figure 4 at the next "T"
maintenance in accordance with the ALS.
Revision 0  2021-08-19  Page 5/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 6 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Non-installed equipment or parts:
Not applicable.
1.F. APPROVAL
The technical content of this document is approved under the authority of the Design Organization Approval
ref. EASA. 21J.700.
For helicopters operated outside the terrain regulated by the EASA, the application of this document is
subject to validation provided by the responsible aviation authority of the state of registry.
The technical content of this document is approved under the prerogatives of the recognition of design
capability ref. FRA21J-002-DGA for French Government helicopters.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following staff
qualifications:
Qualification: - 1 Airframe Technician for the cutout of the X.3855 frame, the installation of the attachment
gussets and the installation of the shims on the rails of the sliding cowling,
- 2 Mechanical Technicians for the removal/installation of the new bracket links.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours: - 24 hours for the Airframe Technician,
- 16 hours for the Mechanical Technician.
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter
configuration.
Helicopter downtime is estimated at 5 days.
1.H. WEIGHT AND BALANCE
Modification 0728521:
There is no change in weight and moment.
Modification 0728904:
There is no change in weight and moment.
Modification 0728496:
- Weight: + 1.205 kg.
- Longitudinal moment: + 5.80 m.kg.
- Lateral moment: + 0.02 m.kg.
Revision 0  2021-08-19  Page 6/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 7 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Modification 0729044:
- Weight: + 0.070 kg.
- Longitudinal moment: + 0.367 m.kg.
- Lateral moment: - 0.004 m.kg.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
The following documents are required for compliance with this ALERT SERVICE BULLETIN.
Standard Practices Manual (MTC):
MTC: 20-02-05-404: Assembly by screws and nuts - Joining
MTC: 20-02-06-404: Safetying with cotter pins - Safetying and locking assemblies
MTC: 20-02-07-403: Use of Vernelec 43022 varnish
MTC: 20-02-09-101: Crack detection through dye-penetrant inspection: General - Crack detection
MTC: 20-02-09-601: Checking structural parts / components using the dye penetrant procedure - Crack
MTC: 20-04-01-102: Use of cleaning products on individual parts and on helicopters - Cleaning
MTC: 20-04-04-403: Touch-up of the Alodine 1200 protection (Bonderite M-Cr 1200) - Surface treatment
before painting
MTC: 20-04-05-101: Painting equipments and paint touch-ups - General - Paint and primer application
MTC: 20-04-05-402: Application of Epoxy primer P05 - P20 - Paint and primer application procedure
MTC: 20-05-01-211: Sealing compound Mastinox 6856 K (CM 518) and 6856 H - General sealing
procedures
MTC: 20-05-01-223: Use of Sealing compounds sealing 1776 B2 / 1776 S - General sealing procedures
MTC: 20-05-01-226: Application of Sealing Compound PR 1782 B2 - General sealing procedures
MTC: 20-05-01-227: Application of Jointing Compound CA 1010 - General sealing procedures
MTC: 20-06-01-407: Application of EC adhesive 2216 B/A (CM 664) - Bonding with adhesives
MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions
MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions
MTC: 20-08-05-101: Drafting and updating the log card (F-M) - General rules applicable to aircraft
MTC: 20-08-05-103: Monitoring of parts in operation - marking - service life customization - General rules
applicable to aircraft
Revision O  2021-08-19  Page 7/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 8 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Aircraft Maintenance Manual (MMA):
MMA: 53-00-00-611: General Standard Maintenance Instructions - GENERAL.
MMA: 53-26-00-061: MGB Attachment Fitting Removal-Installation - FITTINGS AND MOUNTS.
MMA: 53-26-00-212: Check of tightening torques - FITTINGS AND MOUNTS
MMA: 62-10-00-061: Removal/Installation - MAIN ROTOR BLADES.
Information Notice:
IN: 3481-1-00: The Marketplace: an AirbusWorld Ordering service
IN: 3686-1-00: GENERAL Publishing of complementary Instructions for Continued Airworthiness through
Delivery Notes
IN: 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight
Safety Promotion Notice (SPN):
SPN: 3703-P-00: Foreign Object Damage prevention
1.L. OTHER AFFECTED PUBLICATIONS
CAUTION
ALERT SERVICE BULLETIN, THE OPERATOR
MUST MAKE SURE THAT ALL THE MAINTENANCE
DOCUMENTS  NECESSARY  FOR
MAINTENANCE OF THIS INSTALLATION ARE
AVAILABLE. IF THEY ARE NOT AVAILABLE,
OPERATOR  CONTACT
HELICOPTERS TO GET  THESE
DOCUMENTS.
The changes to Instructions for Continued Airworthiness (ICA) which are required as a result of this SB will
be incorporated in the next Normal Revision. Refer to DN.002.0017 until the information is available in the
published technical documentation
NOTE 4
You can find more information about Delivery Notes
in Information Notice IN 3686-1-00.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
1.M.1. Modification 0728521:
Not applicable.
1.M.2. Modification 0728904:
Not applicable.
Revision 0  2021-08-19  Page 8/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 9 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
1.M.3. Modification 0728496:
Interchangeability:
PRE MOD 0728496 and POST MOD 0728496 components are not interchangeable.
Mixability:
Mixing between PRE MOD and POST MOD 0728496 components is prohibited.
1.M.4. Modification 0729044:
Not applicable.
Revision 0 2021-08-19  Page 9/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 10 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For information about the price of the modification kits and/or components, or for aid, contact the Airbus
Helicopters Network Sales and Customer Relations Department.
Availability
Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's
request.
Procurement
Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
The guide for the cutout of the X3855 frame (zz)
(modification 0728521) can be used for multiple helicopters.
Only one will be delivered per maintenance workshop.
2.B. LOGISTIC INFORMATION
Not applicable.
Revision 0  2021-08-19  Page 10/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 11 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Kits to be ordered for one helicopter or one assembly:
New  Old
Key Word  Qty  P/N  Item  P/N  Instruction
MK2/MK2+ MGB
332A07-2849-6071
bracket link
MGB front bracket  4  332A22-3643-20  1  332A22-1613-21 or  Discard
screw  332A22-1613-20
Front cylindrical  4  332A22-3647-20  2
bobbin
Concave washer  332A22-3656-20  330A22-0136-20  Discard
ø 12.5
Flat washer  332A22-3651-20  4
ø 12.5
Convex washer  ø 12.5  4  332A22-3655-20  5  330A22-0137-20  Discard
Front peel shim  332A22-3653-20  6  332A22-1665-51  Discard
Lining  8  332A22-3649-20  7
Flat washer  332A22-3651-22  8
ø 12.5
Bi-hexagonal  8  ECS2271BH120N  9  ASNA0045BC120L  Discard
deformation nut
Convex washer  332A22-3657-20  10  330A22-0139-20  Discard
ø 10.5
MGB rear bracket  8  332A22-3644-20  11  332A22-1614-20  Discard
screw
bobbin  Rear cylindrical  332A22-3648-20  12
Flat washer
16  332A22-3652-20  13
ø 10.5
Concave washer  8  332A22-3658-20  14  330A22-0138-20  Discard
ø 10.5
LH rear peel shim  1  332A22-3654-20  15  332A22-1666-55  Discard
Lining  16  332A22-3650-20  16
Flat washer
16  332A22-3652-22  17
ø 10.5
Bi-hexagonal  deformation nut  16  ECS2271BH100N  18  ASNA0045BC100L  Discard
RH rear peel shim  1  332A22-3654-21  19  332A22-1666-56  Discard
Split pin  12  23310CA020025  20  23310CA020025  Discard
LH shim  1  332A22-3653-21  21
LH rear shim  1  332A22-3654-22  22
RH rear shim  1  332A22-3654-23  23
NOTE 3
The number of nuts (9) and (18) has been doubled in
relation to the needs of this ALERT SERVICE BULLETIN.
Revision 0  2021-08-19  Page 11/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 12 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
New  Old
Key Word  Qty  P/N  Item  P/N  →  Instruction
Retrofit kit, 26°
beam attachment  332A07-2890-4071
gussets
LH attachment  1  332A22-1730-21  31
gusset
RH attachment  1  332A22-1730-20  32
gusset
Flat round-head  8  ECS2151DXJ3211  33
rivet
Flat round-head  20  ASNA2050DXJ4011  34
rivet
Flat round-head  44  ECS2151DXJ3207  35
rivet
Flat round-head  8  ASNA2050DXJ4009  • 36
rivet
Countersunk 100°
24  ASNA2049DXJ4010  37
rivet
Flat round-head  8  21215DC3208J  38
rivet
Flat round-head
4  21215TB4010  39
rivet
Locking hexagonal  14  ASN52320BH050N  • 40
nut
Locking hexagonal  16  ASN52320BH060N  41
nut
NOTE 4
There are twice the number of the rivets (33) to (39) and the
nuts  (40)  (41)  required  this
ALERT SERVICE BULLETIN.
Equipment or parts to be ordered separately:
New  Old
Key Word  Qty  Item
P/N  P/N  Instruction
Cowling LH rail  1  332A58-1341-20  30
shim
Locking hexagonal  6  ASN52320BH050N  40
nut
Cowling RH rail  1  332A58-1341-21  44
shim
Countersunk head
6  22256BC050018L  45
screw
Revision 0  2021-08-19  Page 12/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 13 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Plain washer  6  23116AG050LE  48
Consumables to be ordered separately:
As per Work Cards and Tasks mentioned in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  Consumable P/N  CM  Item
Grease  AR  AIR 4210 B  115  24
Sealing compound  AR  ECS 2068.10  6240  25
Chemical transformation agent  AR  ECS 2338.10  316  26
Anticorrosion agent  AR  ECS 7009  518  27
400-grit abrasive paper  AR  Commercial  28
Sealing  AR  ECS2422-50  6068  29
Red paint  AR  ECS2274-20-3020  4929  42
Sealing compound  AR  ECS2339.10  6068  43
Adhesive  AR  DHS172-172.20  664  47
Varnish  AR  ECS 2228.10  514  48
You can order the consumables from the AirbusWorld Marketplace through e-ordering (IN 3481-1-00).
If you cannot get access to e-ordering, please contact your Logistic Focal Point.
Special tools:
As per Work Cards and/or Tasks mentioned in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  Tool or equivalent P/N  Item
Guide for cutout of X3855 frame  X530P8101101  ZZ
Black indelible ink pen  Commercial P/N  УУ
ZZ
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0  2021-08-19  Page 13/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 14 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- As per Work Card 20-02-05-404 (MTC), read and comply with the instructions for assembly by screws and
- As per Work Card 20-02-06-404 (MTC), read and comply with the instructions for safetying with cotter pins.
- As per Work Card 20-02-09-101 (MTC), read and comply with the instructions for crack detection through
dye-penetrant inspection.
- As per Work Card 20-04-01-102 (MTC), read and comply with the instructions for use of cleaning products
on individual parts and on aircraft.
- As per Work Card 20-04-05-101 (MTC), read and comply with the general information about painting
means and paint touch-ups.
- As per Work Card 20-05-01-211 (MTC), read and comply with the instructions about the use of sealing
compound Mastinox 6856 K and 6856 H.
- As per Work Card 20-05-01-223 (MTC), read and comply with the instructions about the use of sealing
compound PR1776 B2/ 1776 S.
- As per Work Card 20-05-01-226 (MTC), read and comply with the instructions about the use of sealing
compound PR1782 B2
- As per Work Card 20-05-01-227 (MTC), read and comply with the instructions about the use of jointing
compound CA 1010.
- As per Work Card 20-06-01-407 (MTC), read and comply with the instructions about the use
of adhesive E.C. 2216 B/A (CM 664).
NOTE 1
The rivet length is a theoretical value. Airbus Helicopters
refers to the standard design definition to calculate this
value. It is possible that there are differences between the
standard design definition and the current helicopter
contiguration. The applicable Work Card (MTC) and/or the
specification standard of the rivets helps you calculate the
correct rivet length. You can use a rivet that is different from
the rivet given in this ALERT SERVICE BULLETIN if your
rivet has the correct calculated rivet length.
3.B. WORK STEPS
CAUTION
MAKE SURE THAT YOU PREVENT ALL POSSIBLE
FOREIGN OBJECT DAMAGE (FOD). REFER TO
SAFETY  PROMOTION  NOTICE  (SPN)
No. 3703-P-00.
3.B.1. Preliminary steps
- Disconnect all electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Install the necessary means of access.
- Remove the blades as per Task 62-10-00-061 (MMA).
- Remove the linings necessary for adequate access to the various work areas.
Revision 0  2021-08-19  Page 14/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 15 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
CAUTION
IT IS MANDATORY TO COMPLY WITH THE
GENERAL  INSTRUCTIONS  AS  PER
TASK  53-00-00-611 (MMA) BEFORE  ANY
INTERVENTION ON THE FUSELAGE STRUCTURE.
- If necessary, remove the cabin ceiling soundproofing panels at the X3855 and X5295 frames.
3.B.2. Cut-out of the X3855 frame and replacement of the attachment gussets
3.B.2.a. Cut-out of the X3855 frame - modification 0728521 (Figure 1) (only for configurations 1, 2, 3 and 5)
- Perform a cut-out on the X3855 frame using the special tool (zz) as per Appendix 4.A.
- Sand the cutout area using abrasive paper (28).
- Perform a touch-up by applying the chemical transformation agent (26) on the cutout as per
Work Card 20-04-04-403 (MTC).
- Protect the cutout as per Work Card 20-04-05-402 (MTC).
Revision 0 2021-08-19  Page 15/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 16 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3.B.2.b. Replacement of the gussets - modification 0728904 (Figures 8, 9 and 10) (only for configurations
1, 2, 6 and 7)
- Remove the rivets (q) and the clamp supports (r).
- Keep the clamp supports (r).
Rear RH side of the X5295 frame  Front RH side of the X5295 frame
- Remove the rivets (s) from the support (t).
Remove the screws (u), the bushes (v), the nuts (w) and the washers (x).
- Remove the footstep (y).
- Discard the nuts (w).
u
Revision 0  2021-08-19  Page 16/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 17 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- Remove the screws (z), (ab), the washers (ac), (ad) and the nuts (ae).
- Discard the nuts (ae).
X5295
WD  FWD
ab  Z
ac
ad  ad  ad
ae  ae  ae
- Removal of the RH gusset (ah) at the rear of the X5295 frame as per Figures 8 and 9:
. remove the rivets (af), (ak), (al), (am) and (an),
. remove the RH gusset (ah),
. discard the gusset (ah),
clean the area left bare by the removed gusset (ah) on the longeron (ao).
- Removal of the LH gusset (ai) at the rear of the X5295 frame as per Figures 8 and 10:
. remove the rivets (af), (ak), (al), (am) and (an),
. remove the LH gusset (ai),
. discard the gusset (ai),
. clean the area left bare by the removed gusset (ai) on the longeron (ap).
- Remove the three RH rivets (aj) at the front of the X5295 frame as per Figure 9, Section A-A
- Remove the three LH rivets (aj) at the front of the X5295 frame as per Figure 10, Section A-A
Revision O  2021-08-19  Page 17/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 18 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- Installation of the new RH gusset (32) at the rear of the X5295 frame as per Figures 8 and 9:
position and adjust the new gusset (32) on the longeron (ao),
counter-drill the new gusset (32) to match the existing holes on the longeron (ao),
. perform the touch-ups by applying the chemical transformation agent (26) as per
Work Card 20-04-04-403 (MTC),
. apply protection as per Work Card 20-04-05-402 (MTC),
. perform the paint touch-ups,
. enlarge the holes of the rivets (am) and (al) by 4 mm (.157 in) on the longeron (ao) and the new
gusset (32),
. countersink the three holes for the rivets (am) on the X5295 frame and the new gusset (32)
as per Figure 9, Section B-B,
. install the new gusset (32) with the sealing compound (43) and the rivets (33), (34), (35), (36) and (37).
- Installation of the new LH gusset (31) at the rear of the X5295 frame as per Figures 8 and 10:
. position and adjust the new gusset (31) on the longeron (ap),
counter-drill the new gusset (31) to match the existing holes on the longeron (ap),
• perform the touch-ups by applying the chemical transformation agent (26)
as per Work Card 20-04-04-403 (MTC),
. apply protection as per Work Card 20-04-05-402 (MTC),
. perform the paint touch-ups,
. enlarge the holes of the rivets (am) and (al) by 4mm (.157 in) on the longeron (ap) and the new
gusset (31),
. countersink the three holes for the rivets (am) on the X5295 frame and the new gusset (31) as per
Figure 10, Section B-B,
. install the new gusset (31) with the sealing compound (43) and the rivets (33), (34), (35), (36) and (37).
- Countersink the three holes for the RH rivets (37) at the front of the X5295 frame
as per Figure 9, Section A-A.
- Countersink the three holes for the LH rivets (37) at the front of the X5295 frame
as per Figure 10, Section A-A.
- Perform the touch-ups by applying the chemical conversion material (26) as per
Work Card 20-04-04-403 (MTC).
- Install the three RH rivets (37) at the front of the X5295 frame as per Figure 9, Section A-A.
- Install the three LH rivets (37) at the front of the X5295 frame as per Figure 10, Section A-A.
- Apply protection as per Work Card 20-04-05-402 (MTC).
- Perform the paint touch-ups.
Revision 0 2021-08-19  Page 18/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 19 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- Install the screws (z), (ab) and the washers (ac), (ad) with the new nuts (41).
- Tighten the new nuts (41) to the torque values indicated below.
×5295
FWD  FWD
— ab
ac
ad
41  41
0.9-1.1 daN.m
79.65-97.35 Ibf.in
- Apply sealing compound (25) to the heads of the screws (z) and (ab).
- Perform the paint touch-ups.
- Mark a red line on the head of the screws (z), (ab) and the plates (n), (o) with the paint (42).
Revision 0  2021-08-19  Page 19/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 20 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- Install the footstep (y) with the screws (u), the bushes (v), the washers (x) and the new nuts (40).
- Tighten the new nuts (40) to the torque value indicated below.
- Apply sealing compound (25) to the heads of the screws (u).
- Perform the paint touch-ups.
- Mark a red line on the head of the screws (u) and the structure with the paint (42).
- Install the support (t) with the rivets (39) and the sealing compound (43).
39
FWD
0X00  Larg
0.4-0.5 daN.m  40
35.4-44.25 Ibf.in
Revision 0 2021-08-19  Page 20/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 21 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- Install the clamps supports (r) with the rivets (38).
•38
38
Rear RH side of the X5295 frame  Front RH side of the X5295 frame
3.B.2.c. Installation of the shims on the rails of the rear sliding cowling - modification 0729044 (only for
configurations 1, 4, 5 and 7)
3.B.2.c.1.a. Installation of the shims on the rails without the edge strip (PRE MOD 0726238) (Figures 11 and 12)
(For helicopters which have not complied with the former revisions of this
ALERT SERVICE BULLETIN)
- Position the LH shim (30) on the LH rail (au) and the RH shim (44) on the RH rail (av)
as per Figure 12, Detail Q.
- Counter-drill the LH rail (au) to match the LH shim (30).
- Counter-drill the RH rail (av) to match the RH shim (44).
- Perform deburring on the LH rail (au) and the RH rail (av).
- Perform the touch-ups on the protections on the LH rail (au) and the RH rail (av) as per
Work Cards 20-04-05-402 and 20-04-04-403 (MTC).
- Apply adhesive (47) to the ends of the shims (30) and (44) up to the attachment holes (aw) as per
the hatched area Figure 12, Detail Q.
- Install the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) with the screws (45),
the washers (48) and the nuts (40).
- Tighten the nuts (40) to the standard torque value.
3.B.2.c.1.b. Installation of the shims on the rails without the edge strip (PRE MOD 0726238) (Figures 11 and 12)
(For helicopters which have complied with the former revisions of this ALERT SERVICE BULLETIN)
- Remove the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) (Figure 12).
- Removed and discard the washers (ay).
- Install the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) with the screws (45),
the washers (48) and the nuts (40).
- Tighten the nuts (40) to the standard torque value.
Revision 0  2021-08-19  Page 21/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 22 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3.B.2.c.2.a. Installation of the shims on the rails with the edge strip (POST MOD 0726238) (Figures 11 and 13)
(For helicopters which have not complied with the former revisions of this
ALERT SERVICE BULLETIN)
- Remove and discard the nuts (ar), the washers (as) and the screws (at).
- Apply adhesive (47) to the ends of the shims (30) and (44) up to the attachment holes (aw) of
the screws (at) as per the hatched area Figure 13, Detail R.
- Install the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) with the screws (45),
the washers (48) and the nuts (40).
- Tighten the screws (40) to the standard torque value.
3.B.2.c.2.b. Installation of the shims on the rails with the edge strip (POST MOD 0726238) (Figures 11 and 13)
(For helicopters which have complied with the former revisions of this ALERT SERVICE BULLETIN)
- Remove the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) (Figure 13).
- Removed and discard the washers (ay).
- Install the shim (30) on the LH rail (au) and the shim (44) on the RH rail (av) with the screws (45),
the washers (48) and the nuts (40).
- Tighten the nuts (40) to the standard torque value.
3.B.3. New link of the MGB suspension bar attachment brackets - modification 0728496
3.B.3.a. Removal of the MGB attachment brackets (Figures 2 and 3)
- Remove the front bracket (a) and the rear brackets (b) and (c) as per subtask 53-26-00-031-001
of Task 53-26-00-061 (MMA).
- Keep the brackets (a), (b) and (c).
- Discard the nuts (p), pins (d), convex washers (e), concave washers (f) and screws (g).
- Remove and keep the peel shims (h), (k) and (I).
- Record the thickness of the peel shims (h), (k) and (I) on the digital feedback sheet. Refer to
Appendix 4.B.
- Clean and degrease the peel shims (h), (k) and (I).
NOTE 2
The digital feedback sheet is completed when this
ALERT SERVICE BULLETIN is apply through the QR code.
NOTE 3
The peel shims (h), (k) and (I) can be whole, partial or
absent.
CAUTION
THE PEEL SHIMS (h), (k) AND (I) MUST BE USED
AS TEMPLATES TO DEFINE THE SHAPE AND
THICKNESS OF THE PEEL SHIMS (6), (15)
AND (19).
- Check the installation drawing of the plates and brackets as per subtask 53-26-00-221-001 of
Task 53-26-00-061 (MMA).
- Make sure there is no corrosion in the X3855 and X5295 frame bores.
Revision 0  2021-08-19  Page 22/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 23 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- If there is corrosion:
. Remove the traces of corrosion with 400-grit abrasive paper (28).
• Apply protection using the chemical transformation agent (26).
. Perform the paint touch-ups.
• If damage is still visible, contact Airbus Helicopters technical support at the following address:
https://keycopter.airbushelicopters.com,
- Make sure that there are no cracks on the X3855 and X5295 frames at the attachment bracket fixations
(a), (b) and (c) as per Work Card 20-02-09-601 (MTC).
- If there are cracks, contact Airbus Helicopters technical support at the following address:
https://keycopter.airbushelicopters.com,
- Check the brackets (a), (b) and (c) as per subtask 53-26-00-221-003
of Task 53-26-00-061 (MMA).
- Re-identify the front plate (m) as per paragraph paragraph 3.C. using a pen (yy) and
as per Figure 7, Detail M.
- Apply varnish (48) (not shown) on the re-identification as per Work Card 20-02-07-403 du MTC.
3.B.3.b. Presentation of the new front bracket link (Figure 4)
CAUTION
DO NOT APPLY GREASE (24) AND DO NOT
TIGHTEN TO TORQUE DURING COMPLIANCE
WITH PARAGRAPH 3.B.3.b.
- On the workbench:
. Define the thickness and shape of the peel shim (6) according to the width and shape of the removed
peel shim (h) and, if necessary, the shim (21).
. Discard the peel shim (h).
• Install the eight linings (7) on the four screws (1) at a distance of 46 mm ‡ 1 (1.811 in + .0393) from the
shoulder of the screws (1) as per Figure 4.
NOTE 4
Two linings (7) must be installed alternately on each screw
(1) as indicated below.
Revision 0  2021-08-19  Page 23/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 24 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- On the helicopter:
. Apply anticorrosion agent (27) on the surfaces in contact with the front bracket (a), the front plate (m),
the front peel shim (6) and, if necessary, the shim (21) (Figure 4, Section A-A and Figure 7, Detail ).
. Install the front peel shim (6) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
. Install the front bracket (a) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
• Make sure that the centering pin (a1) (not shown in the Figure) of the front bracket (a) is correctly
engaged on the front plate (m).
. Make sure that the front peel shim (6), the shim (21) if present, and the front bracket (a) are aligned.
• Assemble the screws (1), flat washers (4) and cylindrical bobbins (2).
. Install the screw (1), flat washers (4) and cylindrical bobbins (2) assembly on the X3855 frame.
. Make sure that the position of the cylindrical bobbins (2) on the X3855 frame is correct as per Figure 4.
. Install the concave washers (3) and the convex washers (5).
. Make sure that the concave washers (3) and the convex washers (5) are correctly stacked.
. Install the washer(s) (8) and/or (4) as per Table No. 2 below, until length L1 is less than or equal
to 15 mm (.590 in),
NOTE 5
The washers are added in order to set pin hole at the bottom
of slot when nut is screwed to contact without torquing in
accordance with the order of the following. Refer to the
table No. 2 below.
Table No. 2
Number of washers (4)  Number of washers (8)
Case 0  1
Case 1
AND  1
Case 2  1  2
Case 3  2
not OK
Revision 0  2021-08-19  Page 24/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 25 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
CAUTION
AT LEAST,  HALF OF THE DIAMETER OF
THE PIN (20) MUST BE TAKEN INSIDE THE NUT (9)
AFTER FINAL TORQUING.
NOTE 6
The maximum installation of washers (8) and (4) for a screw
(1) is indicated below.
OR
CAUTION
THREADS  OF THE  SCREWS
MUST BE INSIDE THE CONCAVE WASHERS (3)
AND THE CONVEX WASHERS (5).
. Make sure that the threads of the screws (1) are not inside the front bracket (a) as shown below.
Bracket
•
Threaded area
Screw
Revision 0  2021-08-19  Page 25/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 26 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
CAUTION
DO NOT TIGHTEN THE NUTS (9) TO TORQUE.
• install the four nuts (9) without tightening to torque,
CAUTION
AT LEAST HALF OF THE DIAMETER OF THE
PINS (20) MUST BE HELD BY THE NUTS (9).
• make sure that the pins (20) can be installed on the nuts (9).
- Remove the four nuts (9), the concave washers (3), the convex washers (5), the cylindrical bobbins (2),
the washers (8) and/or (4) the screws (1) and.
- Discard the four nuts (9).
3.B.3.c. Installation of the new front bracket link (Figure 4)
CAUTION
ONLY APPLY GREASE (24) ON THE SHANK OF
THE SCREWS (1) LOCATED INSIDE
BOBBIN (2) AND ON THE NUT THREADS (9). PAY
PARTICULAR ATTENTION TO DEGREASING THE
SURROUNDING SURFACES.
- On the workbench:
. Install the washers (8) and/or (4) on the screws (1).
• Fill the cylindrical bobbins (2) with the grease (24).
. Apply the grease (24) on part of the screw shank (1) and the nut threads (9) as per the following
illustration.
Bobbin  With grease
Without grease
No grease on
external surface of
the bobbin.  With grease
Screw  Without grease
. assemble the screws (1) and the cylindrical bobbins (2).
Revision 0  2021-08-19  Page 26/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 27 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- On the helicopter:
. Install the screws (1), the washers (8) and/or (4) and the cylindrical bobbins (2) assembly on the X3855
frame.
. Make sure that the centering of the cylindrical bobbins (2) with respect to the spot facing of the X3855
frame is correct as indicated below
Frame
Bobbin
• Install the concave washers (3) with the flat side towards the front bracket (a).
. Install the convex washers (5) with the flat side towards nuts (9).
. Make sure that the concave washers (3) and the convex washers (5) are correctly stacked.
• Install four nuts (9), do not tighten to torque.
3.B.3.d. Tightening to torque (Figure 4)
CAUTION
THE NEED TO ALIGN A SLOT IN THE NUTS (9)
WITH A SCREW PINNING HOLE (1) DOES NOT
JUSTIFY EXCEEDING THE MAXIMUM TIGHTENING
TORQUE.
- Tighten the four nuts (9) to the minimum torque indicated in Figure 4.
NOTE T
The nuts (9) must be tightened crosswise.
CAUTION
A MINIMUM SETTLING PERIOD OF 6 HOURS IS
REQUIRED BEFORE THE SECOND APPLICATION
OF TORQUE VALUES.
NOTE 8
The settling phase can take place with the MGB attachment
suspension bars installed.
- After the settling period, tighten the four nuts (9) to the minimum torque indicated in Figure 4.
- Installation of the pins (20):
Revision 0  2021-08-19  Page 27/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 28 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
CAUTION
AT LEAST HALF OF THE DIAMETER OF THE
PINS (20) MUST BE HELD BY THE NUTS (9).
Check the alignment of the slot in the nuts (9) with the pinning hole for the screws (1).
. If not aligned, tighten the nut (9) until one of the slots in the nuts (9) is aligned with a pinning hole for the
screws (1) without exceeding the maximum torque value indicated in Figure 4.
• If the alignment of the slot in the nuts (9) cannot be aligned with one of the pinning holes for the
screws (1), replace the nut (9) and repeat compliance with paragraph 3.B.3.d.
NOTE 9
Changing the nuts (9) does not mean a new settling phase is
necessary.
. Install the pins (20).
- Clean the nuts (9), the screws (1), the concave washers (3), the pins (20) and the convex washers (5).
- Clean the front bracket (a).
- Apply a coat of sealing compound (25) on the nuts (9), the screws (1), the concave washers (3) the split
pins (20) and the convex washers (5) as per Figure 4, Detail F.
- Apply a bead of sealing compound (29) around the front bracket (a) as per Figure 4, Section A-A and
Figure 7, Detail J.
3.B.3.e. Positioning new rear bracket links (Figures 5 and 6)
CAUTION
DO NOT APPLY GREASE (24) AND DO NOT
TIGHTEN TO TORQUE WHEN COMPLYING WITH
PARAGRAPH 3.В.3.e.
CAUTION
THE CUMULATIVE THICKNESS OF THE LH REAR
PEEL SHIM (15) AND THE SHIM (22) MUST BE
EQUAL TO THE THICKNESS OF THE REMOVED
SHIM (k) WITH A TOLERANCE OF ‡ 0.025 MM.
(.00098 in).
CAUTION
THE CUMULATIVE THICKNESS OF THE RH REAR
PEEL SHIM (19) AND THE SHIM (23) MUST BE
EQUAL TO THE THICKNESS OF THE REMOVED
SHIM (I) WITH A TOLERANCE OF ‡ 0.025 MM.
(.00098 in).
Revision 0  2021-08-19  Page 28/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 29 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- On the workbench:
. Define the thickness and shape of the LH rear peel shim (15) as per the thickness and shape of the
removed LH rear peel shim (k) and, if necessary, the shim (22).
. Define the thickness and shape of the RH rear peel shim (19) as per the thickness and shape of the
removed RH rear peel shim (I) and, if necessary, the shim (23).
• Discard the peel shims (k) and (l).
. Install the sixteen linings (16) on the eight screws (11) at a distance of 46 mm‡1 (1.811 in ‡.0393) from
the shoulder of the screws (11) as per Figures 5 and 6.
NOTE 10
Two linings (16) must be installed alternately on each
screw (11) as indicated below.
-16
Revision 0 2021-08-19  Page 29/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 30 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- On the helicopter:
. apply anticorrosion agent (27) on the surfaces in contact with the LH rear bracket (b),
the LH rear plate (n) and the LH rear peel shim (15) (Figure 7, Detail K).
• Apply anticorrosion agent (27) on the surfaces in contact with the RH rear bracket (c),
the RH rear plate (o) and the RH rear peel shim (19) (Figure 7, Detail L).
. If necessary, apply anticorrosion agent (27) on the surfaces in contact with the shims (22) and/or (23).
. If necessary, install the shims (22) and/or (23).
. Install the LH rear peel shim (15) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
. Install the RH rear peel shim (19) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
. Install the LH rear bracket (b) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
. Make sure that the centering pin (b1) of the LH rear bracket (b) is correctly engaged on the LF rear
plate (n).
• Make sure that the LH rear peel shim (15), the shim (22), if present, and the LH rear bracket (b) are
aligned.
• Install the RH rear bracket (c) as per the marking made during removal as specified
in subtask 53-26-00-031-001 of Task 53-26-00-061 (MMA).
. Make sure that the centering pin (c1) of the RH rear bracket (c) is correctly engaged on the RH rear
plate (o).
• Make sure that the RH rear peel shim (19), the shim (23), if present, and the RH rear bracket (c) are
aligned.
. Assemble the screws (11), flat washers (13) and cylindrical bobbins (12).
. Install the screws (11), flat washers (13) and cylindrical bobbins (12) assembly on the X5295 frame.
. Make sure that the position of the cylindrical bobbins (12) is correct on the X5295 frame as per
Figures 5 and 6.
. Install the concave washers (14) with the flat side towards the LH rear bracket (b) and RH
rear bracket (c).
. Install the convex washers (10) with the flat side towards the nuts (18).
. Make sure that the concave washers (14) and the convex washers (10) are correctly stacked.
• Install the washer(s) (17) and/or (13) as per Table No. 3 below until length L2 is less than or equal to 13
mm (.511 in),
NOTE 11
The washers are added in order to set pin hole at the bottom
of slot when nut is screwed to contact without torquing in
accordance with the order of the following. Refer to the table
No. 3 below.
Table No. 3
Number of washers (13)  Number of washers (17)
Case 0  1
Case 1  1  AND  1
Case 2  1  2
Case 3  2
Revision 0  2021-08-19  Page 30/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 31 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
not OK
CAUTION
AT LEAST (20) MUST BE TAKEN INSIDE  HALF OF THE DIAMETER OF
THE PIN
THE NUT (18) AFTER FINAL TORQUING.
NOTE 12
Maximum installation of washers (17) and (13) for a
screw (11) is indicated below.
17  • 13
OR
13
11
CAUTION
THE THREADS OF THE SCREWS (11) MUST BE
INSIDE THE CONCAVE WASHERS (14) AND THE
CONVEX WASHERS (10).
Revision 0  2021-08-19  Page 31/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 32 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
. Make sure that the threads of the screws (11) are not inside the LH rear bracket (b) and the RH rear
bracket (c) as shown below.
Bracket
Threaded area
Screw
CAUTION
DO NOT TIGHTEN THE NUTS (18) TO TORQUE.
. Install the eight nuts (18), do not tighten to torque.
CAUTION
AT LEAST HALF OF THE DIAMETER OF THE
PINS (20) MUST BE HELD BY THE NUTS (18).
. Make sure that the pins (20) can be installed on the nuts (18).
- Remove the eight nuts (18), the concave washers (14), the convex washers (10), the cylindrical
bobbins (12), the washers (17) and/or (13), the screws (11).
- Discard the eight nuts (18).
Revision 0  2021-08-19  Page 32/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 33 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3.B.3.f. Installation of the new rear brackets link (Figures 5 and 6)
CAUTION
ONLY APPLY GREASE (24) ON THE SHANK OF
THE SCREWS (11) LOCATED INSIDE THE BOBBIN
(12) AND ON THE NUT THREADS (18). PAY
PARTICULAR ATTENTION TO DEGREASING THE
SURROUNDING SURFACES.
- On the workbench:
. Install the washer(s) (17) and/or (13) on the screws (11),
. Fill the cylindrical bobbins (12) with the grease (24).
• Apply the grease (24) on part of the screw shank (11), the nut threads (18) as per the below illustration.
Bobbin  With grease
Without grease
No grease on
external surface of
the bobbin.  With grease
Screw  Without grease
Assemble the screws (11) and the cylindrical bobbins (12),
Revision 0 2021-08-19  Page 33/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 34 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- On the helicopter:
. Install the screws (11), washer(s) (17) and/or (13), and cylindrical bobbins (12) assembly on the X5295
frame.
. Make sure that the centering of the cylindrical bobbins (12) with respect to the spot facing of the X5295
frame is correct as indicated below.
Frame
Bobbin
. Install the concave washers (14) with the flat side towards the LH rear bracket (b) and the RH rear
bracket (c).
. Install the convex washers (10) with the flat side towards the nuts (18).
. Make sure that the concave washers (14) and the convex washers (10) are correctly stacked.
. Install the eight nuts (18), do not tighten to torque.
3.B.3.g. Tightening to torque (Figures 5 and 6)
CAUTION
THE NEED TO ALIGN A SLOT IN THE NUTS (18)
WITH A SCREW PINNING HOLE (11) DOES NOT
JUSTIFY EXCEEDING THE MAXIMUM TIGHTENING
TORQUE.
- Tighten the eight nuts (18) to the minimum torque indicated in Figures 5 and 6.
NOTE 13
The nuts (18) must be tightened crosswise.
CAUTION
A MINIMUM SETTLING PERIOD OF 6 HOURS IS
REQUIRED BEFORE THE SECOND APPLICATION
OF TORQUE VALUES.
NOTE 14
The settling phase can take place with the MGB attachment
bars installed.
Revision 0  2021-08-19  Page 34/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 35 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
- After the settling period, tighten the eight nuts (18) to the minimum torque indicated in Figures 5 and 6.
- Installation of the split pins (20):
CAUTION
AT LEAST HALF OF THE DIAMETER OF THE
PINS (20) MUST BE HELD BY THE NUTS (18).
• Check the alignment of the crenulation hole for the nuts (18) with the pinning hole for the screws (11).
. If not aligned, tighten the nut (18) until one of the crenulation holes for nuts (18) is aligned with a pinning
hole for the screws (11) without exceeding the maximum torque value indicated in Figures 5 and 6.
• If the alignment of the crenulation hole for the nuts (18) cannot be aligned with one of the pinning hole
for the screws (11), replace the nut (18) and repeat paragraph 3.B.3.9.
NOTE 15
Changing the nuts (18) does not mean a new settling phase
is necessary.
. Install the pins (20).
Revision 0 2021-08-19  Page 35/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 36 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3.B.3.h. Check of the new links of the rear brackets
Only the RH side is described. Perform the same operational procedure for the LH side.
- On the rear of the X5295 frame:
. measure the clearance J1 between the RH gusset (32) (see Figure 9, Detail N) and the screws (11), the
washers (17) and/or (13), and the bobbin (12) as indicated below,
• measure the clearance J2 between the X5295 frame and the screw (11), the washers (17) and/or (13),
and the bobbin (12) as indicated below.
- On the front of the X5295 frame:
. measure the clearance J1 between the gusset (aq) (see Figure 9, Detail N) and the screw (11), the
washers (17) and/or (13), and the bobbin (12) as indicated below,
. measure the clearance J2 between the X5295 frame and the screw (11), the washers (17) and/or (13),
and the bobbin 12) as indicated below.
Bobbins
X5295
Gusset
Screw  Screw
RH Gusset (32)  Gusset (aq)  Washers  Washers
- If the clearance J1 or J2 is less than 0.5 mm (0.0196 in):
. remove and discard the pin or pins (20),
. remove and discard the nut or nuts (18),
• install the nut or nuts (18) without tightening to torque,
. comply with paragraph 3.B.3.g.
. if the clearance J1 or J2 is still less than 0.5 mm (0.0196 in), contact Airbus Helicopters Technical
Support at the following address: https://keycopter.airbushelicopters.com,
- If the clearances J1 and J2 are more than or equal to 0.5 mm (0.0196 in):
. comply with paragraph 3.B.3.I.
Revision 0  2021-08-19  Page 36/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 37 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
3.B.3.i. Sealing of new rear bracket links
- Clean the nuts (18), the screws (11), the concave washers (14), the pins (20) and
the convex washers (10).
- Clean the LH rear bracket (b) and the RH rear bracket (c).
- Apply a coat of sealing compound (25) on the nuts (18), the screws(11), the concave washers (14) the
split pins (20) and the convex washers (10) as per Figure 5, Detail G and Figure 6, Detail H.
- Apply a bead of sealing compound (29) around the LH rear bracket (b) and the RH rear bracket (c) as per
Figure 5, Section B-B, Figure 6 Section C-C and Figure 7, Details K and L.
3.B.4. Final steps
- If necessary, install the cabin ceiling soundproofing panels at the X3855 and X5295 frames.
- Install all previously removed linings.
- Install the blades as per Task 62-10-00-061 (MMA).
- Perform a visual check of the aircraft following an inspection or intervention
as per Work Card 20-07-03-408 (MTC).
- Connect all electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Remove the means of access.
- Return the feedback sheet in Appendix 4.B. to the following address:
TechnicalSupport.Helicopters@airbus.com
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record full compliance with this ALERT SERVICE BULLETIN, with the revision number, in the helicopter
documents.
- Record compliance with this ALERT SERVICE BULLETIN (see IN 3785-1-00 for instructions):
QR code or hypertext link
NOTE 16
The  recording  of  compliance  with
ALERT SERVICE BULLETIN in the SB Insight tool does not
replace the recording in the helicopter documents.
ASB EC225 53A065
Tracking of modifications in the documentation:
- If necessary, record embodiment of modifications 0728521 and/or 0728904 and/or 0729044 in the
helicopter documents.
- Record full embodiment of modification 0728496 in the helicopter documents.
- Create a Log Card (FM) for the tracking of the front plate P/N 332A08-1729-63 or 332A08-1729-67
as per Work Card 20-08-05-101 (MTC).
- Record modification 0728496 and the ALERT SERVICE BULLETIN number in the Log Card (FM) for the
plates (m), (n) and (o).
Revision 0  2021-08-19  Page 37/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 38 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
NOTE 17
The flight hours of the front plate P/N 332A08-1729-63 or
332A08-1729-67 since installation must be identified; if this
is not applicable then the flight hours will be equal to the
flight hours of the helicopter.
Identification of modifications on equipment or parts:
Identify the equipment or parts as per the following table and/or Work Card 20-08-05-103 (MTC):
Key Word  OLD P/N  New P/N  MOD  Type of marking
X3855 frame A  332A22-3085-20  332A08-1725-12  0728521  Stamp
X3855 frame A  332A22-3085-21  332A08-1725-13  0728521  Stamp
X3855 frame A  332A22-3125-20  332A08-1725-14  0728521  Stamp
X3855 frame A  332A22-1714-20  332A08-1725-15  0728521  Stamp
X3855 frame A  332A22-3125-21  332A08-1725-16  0728521  Stamp
332A22-1667-21  332A08-1729-63
X3855 front plate  or  or  0728496  Pen
332A22-1667-22  332A08-1729-67
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
Refer to the Airworthiness Limitations Section (ALS).
The new front plate reference is added in the ALS through a dedicated Delivery Note; refer to paragraph 1.L.
The maintenance task 53-26-00-212 (MMA) has been revised to include the content of the maintenance
instructions which are in the Appendix of the previous revisions of the ALERT SERVICE BULLETIN; refer to
the paragraph 1.K.
Revision 0 2021-08-19  Page 38/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 39 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
Z=+1680
Z=+1680
Z=+1588
SECTION
C-C
Z=+1463
DECOUPE NERVURE
RIB CUT-OUT
Ra 3.2
X=+3850
Retur to paragraph 3.B.2.
Figure 1
Revision 0 2021-08-19  Page 39/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 40 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 40/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 41 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PRE MOD 0728496
SECTION
A-A
Y=0
Y=-38
Return to paragraph 3.B.3.а.
Figure 2
Revision 0  2021-08-19  Page 41/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 42 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 42/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 43 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
SECTION  В В  PRE MOD 0728496  d  SECTION  C- C
Y= -560
DI
в¢)
Y= +560
EQ
Return to paragraph 3.B.3.а.  в¢)
Figure 3
Revision 0  2021-08-19  Page 43/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 44 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 44/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 45 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
POST MOD 0728496  SECTION  A-A
CM115
5,6-7,3 daN.m
495.64-646.1 bf.in
-20
(See Figure 7) J D
Y=0
Y=-38
CM 115
CM 115
(See Figure 7) M L  1.881in+.0393  46mm+
20
Return to paragraphs 3.B.3.b., 3.B.3.c. and 3.B.3.d.
Figure 4
Revision 0  2021-08-19  Page 45/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US EC NoUScontent - FR_EC_NotListed

### Page 46 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 46/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 47 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
POST MOD 0728496
ECTIO
3 Е
ĄB  CM 115
3,9-4,9 daN.m
345.18-433.68|bf.in
AG
10
K (See Figure 7)
Y= -560
CM 115  1.881int.0393  46mm+1  115
в¢)
вґ)  CM 115
Return to paragraphs 3.B.3.e., 3.B.3.f., 3.B.3.g. and 3.B.3.h.
Figure 5
Revision 0  2021-08-19  Page 47/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 48 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 48/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 49 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
POST MOD 0728496
SECTION
C-C
CM 115
3,9-4,9 daN.m
345.18-433.68 bf.in
20
20
FWD  AL (See Figure 7)
19
23
Y= +560
16
CM 115  1.881 int.0393
Return to paragraphs 3.B.3.e., 3.B.3.f., 3.B.3.g. and 3.B.3.h.
Figure 6
Revision 0  2021-08-19  Page 49/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US EC NoUScontent - FR EC NotListed

### Page 50 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 50/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 51 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
(See Figure 4)
(See Figure 5)
(See Figure 4)
19
23
64 mm
(2.52 in)
(.67 in)  17 mm  3,5 mm
(.138 in)
(.138 in)  3,5 mm
Return to paragraphs 3.B.3.b., 3.B.3.d., 3.B.3.e. and 3.B.3.i.
Figure 7
Revision 0  2021-08-19  Page 51/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 52 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 52/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 53 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
M
Y = 550
(See Figure 9) NO (Se Figure 10)
Y = -550
Figure 8
Revision 0  2021-08-19  Page 53/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 54 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 54/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 55 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
(See Figure 8)
× = 5295  aq  ECTIO
FWD
(1.039 in)
aq
(See Figure 8)
32
FWD  x = 5295  SECTION
B-B
am  в¢)  am.
37  37
вґ)
1 mm
(.039 in)
Return to paragraphs 3.B.2.b. and 3.B.3.h.
Figure 9
Revision O  2021-08-19  Page 55/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 56 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 56/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 57 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
O (See Figure 8)
× = 5295
SECTION
A-A
(.039 in)
• (See Figure 8)
FWD  × = 5295  ECTIO
Л_F
am  B
37
37
mm
(.039 in)
Return to paragraphs 3.B.2.b. and 3.B.3.h.
Figure 10
Revision 0 2021-08-19  Page 57/76
Revision 4  2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 58 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 58/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 59 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
P
P
Q (See Figure 12)
R (See Figure 13)
·600
Y-600
Q (See Figure 12)
R (See Figure 13)
Figure 11
Revision 0  2021-08-19  Page 59/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techpub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

### Page 60 (OCR)

AIRBUS  HELICOPTERS
No. EC225-53A065
PAGE LEFT INTENTIONALLY BLANK
Revision 0 2021-08-19  Page 60/76
Revision 4 2024-05-28  This document is available on the Internet: www.airbushelicopters.com/techoub/
Export Control: US_EC_NoUScontent - FR_EC_NotListed

The text continues at https://openairdocs.org/service-documents/airbus-helicopters/ec225-53a065/file/cec410e6955b.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
