# Airbus Helicopters Alert Service Bulletin EC225-56A013

Copy: Revision 1 ("Airbus Helicopters ASB No. EC225-56A013 Rev 1"), 38 pages: PDF https://openairdocs.org/files/sha256/d6/6a/d66a342ee9c809d998f1ccea8a98b9c5927b4f8dc029b9b0706da467ad18de4c; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a013/file/d66a342ee9c8.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0160, the docket of AD 2023-08-06. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-56A013
- Latest revision known: EC225-56A013, Revision 1, dated February 10, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a013

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-08-06](https://openairdocs.org/ad/2023-08-06.md), effective Jun 22, 2023: Revision 1
- [AD 2020-20-08](https://openairdocs.org/ad/2020-20-08.md), effective Dec 11, 2020: Revision 1

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a013/proposed.md).

## Text (38 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0160, the docket of AD 2023-08-06. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
Civil version: LP
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
WINDOWS - Cabin jettisonable windows
Improvement to the window jettisoning
Corresponds to modification 0728370 or 332P087142.00 or 332P087142.03
For the attention of
Revision No.  Date of issue
Revision 0  2019-04-10
Revision 1  2020-02-10
Summary:
This ALERT SERVICE BULLETIN consists in further improving the jettisoning of windows from inside the cabin, by
replacing the instructions defined in ALERT SERVICE BULLETIN No. 05A046.
Reason for last Revision:
The purpose of revision 1 of this ALERT SERVICE BULLETIN is to cancel effectivity for helicopters with serial
numbers: 2663, 2666, 2670, 2673 and 2742.
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Revision 0  2019-04-10  Page 1/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters PRE-MOD 0728370 or 332P087140.00 or 332P087142.00 or 332P087142.03 except serial
numbers 2663, 2666, 2670, 2673, 2678 and 2742.
NOTE 1
Modification 332P087140.00 consists in improving the
jettisoning of VIP windows and can be embodied through
ALERT SERVICE BULLETIN No. 56C012.
NOTE 2
MOD 0728370 consists in improving the jettisoning system
of the 5 mm thickness windows. Modifications
332P087142.00 and 332P087142.03 consist in improving
the jettisoning system of the 6.3 mm thickness windows.
These modifications are the subject of this ALERT SERVICE
BULLETIN.
NOTE 3
The helicopters with serial numbers 2663, 2666, 2670, 2673,
2678 and 2742 are not concerned by this ALERT SERVICE
BULLETIN.
1.A.2. Non-installed equipment or parts
On removable doors and panels.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
Revision 0  2019-04-10  Page 2/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
1.C. REASON
Revision 0:
Airbus Helicopters introduced a protective measure through the ALERT SERVICE BULLETIN
No. 05A046, which consisted in installing a PTFE skin film between the frame and the seal of jettisonable
windows, to reduce the level of effort required for jettisoning.
Airbus Helicopters has developed an improvement which consists in removing the PTFE skin and installing
silicone seals instead of the seals currently installed on the helicopter cabin windows.
This ALERT SERVICE BULLETIN supercedes the instructions given in ALERT SERVICE BULLETIN
No. 05A046.
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Revision 1 :
The specific configuration of helicopters with serial numbers 2663, 2666, 2670, 2673 and 2742 has led
Airbus Helicopters to define a specific rework solution for them.
Consequently the purpose of revision 1 of this ALERT SERVICE BULLETIN is to cancel effectivity for
helicopters with serial numbers: 2663, 2666, 2670, 2673 and 2742.
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
- Removing, if installed, the PTFE skin present between the door frame and the cabin windows.
- Measuring the thickness of each window.
- Measuring the clearance between each window and the structure.
- Replacing the seals of cabin windows with silicone seals.
- Returning the response form.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
Revision O  2019-04-10  Page 3/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
1.E.2. Compliance in service
The work must be performed on the helicopter by the operator.
Helicopters/installed equipment or parts:
Comply with paragraph 3.B. as per table No. 1 below:
Table No. 1
Helicopters  Conditions  Compliance time  Paragraphs to comply  with
within 250 flying hours or 6
months (the first limit
Configuration 1  reached is applicable) as  3.B.1.a.
thickness window):  Helicopters defined  (5mm (.196 in)  Helicopters which do not  operate over water  from receipt of this ALERT  SERVICE BULLETIN at  the date mentioned in  З.В.З.а.  3.B.3.b.  3.В.2.
in paragraph 1.A.1.  except for the  following  within 110 flying hours or 6  months (the first limit  page footer.  3.B.3.c.  3.В.3.е.  3.B.4.
2648, 2718, 2731,  helicopters (S/N):  Helicopters which operate  over water  from receipt of this ALERT  reached is applicable) as  3.B.7.a.  3.В.5.а.  3.B.6.
2885, 2901.  SERVICE BULLETIN at
3.B.8.
the date mentioned in
page footer.
within 250 flying hours or 6
Configuration 2  Helicopters which do not  operate over water  from receipt of this ALERT  reached is applicable) as  SERVICE BULLETIN at  months (the first limit  3.B.3.b.  3.B.1.b.  З.В.З.а.  3.B.2.
(6.3mm (.248 in)  the date mentioned in
thickness window):  Helicopters (S/N):  within 110 flying hours or 6  page footer.  3.B.3.e.  3.B.3.d.
2648, 2718, 2731,  months (the first limit  3.B.5.b.  3.В.4.
2885, 2901.  reached is applicable as
Helicopters which operate  3.B.6.
from receipt of this ALERT
over water  3.B.7.0.
SERVICE BULLETIN at
the date mentioned in  3.B.8.
page footer.
Non-installed equipment or parts:
Comply with paragraph 3 of this ALERT SERVICE BULLETIN before installing on the helicopter.
Revision 0 2019-04-10  Page 4/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
1.F. APPROVAL
Approval of modifications:
Configuration 1
The information or instructions relate to modification 0728370, which was approved on March 07, 2019 by
the EASA for civil version helicopters subject to an Airworthiness Certificate.
Configuration 2
The information or instructions relate to modifications 332P087142.00 and 332P087142.03, which was
approved on December 19, 2018 under the EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision O was approved
on April 04, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on April 04, 2019 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French
Government helicopters.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on February 03, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil
version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on February 03, 2020 under the prerogatives of the recognition of design capability FRA21J-002-DGA for
French Government helicopters.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following staff
qualifications
Qualification: - 1 Airframe Technician to remove the PTFE skin,
- 2 Airframe Technicians to remove /install the windows.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours: 2 hours per windows for the 2 Airframe Technicians.
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter
configuration.
Helicopter downtime is estimated at 6 days including time for the removal /installation of the coverings.
1.H. WEIGHT AND BALANCE
Not applicable.
Revision 0 2019-04-10  Page 5/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
The following documents are required for compliance with this ALERT SERVICE BULLETIN:
Standard Practices Manual (MTC):
- MTC: 20-02-05-404: Assembly by screws and nuts - Joining.
- MTC: 20-04-01-102: Use of cleaning products on individual parts and on aircraft - Cleaning.
- MTC: 20-04-01-402: Cleaning of removed individual parts with liquid solvents - Cleaning.
- MTC: 20-05-01-212: Implementation of Sealing compound CM 6232 - General sealing procedures
- MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions.
- MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions.
Aircraft Maintenance Manual (MMA):
- MMA: 56-20-00-051: Removal - Installation - CABIN WINDOWS.
- MMA: 56-20-00-212: Check of Clearance Between Jettisonable Window Seal and Cabin Covering - CABIN
WINDOWS.
1.L. OTHER AFFECTED PUBLICATIONS
The modification will be integrated into:
- Illustrated Parts Catalog (IPC),
- The Aircraft Maintenance Manual (MMA).
The MMA will be updated as part of a future revision.
The update of the IPC must be ordered by the customer.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
The PRE MOD and POST MOD seals are not interchangeable.
The PRE MOD and POST MOD seal keys are not interchangeable.
Mixability:
Having PRE MOD window assemblies (seal, seal keys and PTFE skin) and POST MOD window assemblies
(seal and seal keys) on the same helicopter is authorized.
Revision 0  2019-04-10  Page 6/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
2_  EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
For any information about the kits and/or components, contact the Airbus Helicopters Network Sales &
Customer Relations Department.
Delivery deadlines will be indicated by Sales and Customer Relations Department on Operator's request.
Order the required quantities from the Airbus Helicopters Network Sales and Customer Relations
Department:
Airbus Helicopters
Etablissement de Marignane
Direction des Ventes et Relation Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specity the mode of
transport, the destination and the serial numbers of the
helicopter to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4 42 85 99 96.
2.B. LOGISTIC INFORMATION
For any information, contact the Sales and Customer Relations Department.
Revision O  2019-04-10  Page 7/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
NOTE 3
The quantities of components necessary for a helicopter can
differ as per configuration. It is not necessary to use all these
components.
Kit to be ordered for a configuration 1 helicopter:
New P/N  Old
Key Word  Qty  Item
P/N  →  Instruction
5 mm window seal
332A07-2837-0071
85D kit
85D silicone  151601505M
1
window seal  (704A39-8210-66)
85D silicone  151601506N
window seal key  2  (704A39-8210-67)  2
Key extraction tape  332A23-0520-04  З
Window extraction
8  332A23-0520-07  4
tape
Simple key  4  332A23-0520-06  5
extraction tape
Flat washer  23111AG04OLE  6
Self-locking nut  8  ASN52320BH040N  7
Round head screw  A0099BC040016L  8
Flat washer  8  23112AG04OLE  9
Kit to be ordered for a configuration 2 helicopter:
New P/N  Old
Key Word  Qty  Item
P/N  →→  Instruction
6.3 mm window  332P08-7142-0071
seal 85D kit
85D silicone  151601505M
1
window seal  (704A39-8210-66)
85D silicone  151601506N
2
window seal key  (704A39-8210-67)
Key extraction tape  8  332A23-0520-04
Window extraction
8  332A23-0520-07  4
tape
Simple key  8  332A23-0520-06  5
extraction tape
Flat washer  8  23111AG04OLE  6
Self-locking nut  ASN52320BH040N  7
Flat washer  23112AG04OLE  9
Round head screw  8  A0099BC040018L  16
Revision 0  2019-04-10  Page 8/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
Consumables to be ordered separately:
As per Work Cards and Tasks mentioned in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  Consumables P/N  Ite
Cleaning agent
(Gasoline G)
N8955004956  CM 232  10
Or  AR
Petrol ether  AR  Off the shelf  10
Sealing compound  AR  ECS 6046-1198  CM 6232  11
Webbed adhesive tape  AR  Type 3M 22888 or equivalent  12
Adhesive tape  AR  DHS171-143.21  CM 6229  13
Abrasive paper, 80-grit  AR  Off the shelf  14
PTFE skin  AR  SCOTCH PTFE 5480 - 25.4MM  15
The consumables can be ordered separately from the following companies:
Aviatec global aviation
Website : www.aviatec.net
Telephone: +33 1.34.46.45.24 or +49 4193 8803 630
Fax : +33 1.34.46.45.26 or +49 4193 8803 699
AOG : +49 4193 8803 660
AOG email : aog @aviatec.aero
BDSI
Website : www.boeingdistribution.com
Telephone: +1.305.925.2600
Fax : +1.305.507.7191
AOG : +1.305.471.8888
AOG email : AOGdesk@Boeingdistribution.com
Gaches chimie
Website : www.gaches.com
Telephone : +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email : marketplace@gaches.com
Revision 0  2019-04-10  Page 9/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
Special tools:
Key Word  Qty  Tool P/N or equivalent  Item
Tool kit  KA6420
Spatula, rounded end  770150225 (commercial P/N)  ZZ
Tube cutter  Off the shelf (Virax 215032)
Insertion tool  Off the shelf (LT 415)
Spatula, curved  1479N/S5 ("Beta" supplier P/N)  ww
Key Word  Qty  Tool P/N or equivalent  Item
Measurement kit  332A98-8701-00
Collet  5  Thickness: 8mm  VV
Key Word  Qty  Tool P/N or equivalent  Item
Digital caliper gage  Off the shelf  uu
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision O  2019-04-10  Page 10/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Read and comply with the instructions on assembly by screws and nuts as per Work Card
20-02-05-404 (MTC).
- Read and comply with the instructions for use of cleaning products on individual parts and on aircraft as per
Work Card 20-04-01-102 (MTC).
3.B. WORK STEPS
NOTE 1
The installation of new seals (1) and seal keys (2) must be
done dry.
NOTE 2
The quantity, location and dimensions of the cabin windows
can differ as per the configuration of the helicopter, but the
procedure is identical.
Compliance with the procedure for installing the seals is described in a video, which is accessible by
following the link below:
http://dai.ly/k3DklgBuVI85w|pfkm2
3.B.1. Preliminary steps (Configurations 1 and 2)
- Disconnect all electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Install the access equipment.
- Remove all coverings to get access to the different work areas.
3.B.1.a. Configuration 1 (Figures 1 and 2)
- Identify the location of the internal extraction tapes or handles (as per Appendix 4.C.) of the seal keys (o)
and (p) (not shown in the Figure) before removing them.
- Remove the cabin windows (g) to (g11) Figure 1 as per Task 56-20-00-051 (MMA).
- Record the cabin window part numbers on the response form in Appendix 4.A.
- As per Figure 2 Sections C-C and D-D:
• Remove the nuts (r), washers (t), screws (u), extraction tapes (w), (x) and (y), inside extraction tapes or
handles (o) and (p) (not shown in the figure) and the press-studs (v).
. Keep the press-studs (v) and the inside extraction tapes or handles (o) and (p).
Revision 0 2019-04-10  Page 11/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.1.b. Configuration 2 (Figures 3 or 4 and 5)
NOTE 3
For helicopters (S/N) 2648, 2718 and 2731, refer to figures 3
and 5 with the windows (g12) to (g23).
For helicopters (S/N) 2885 and 2901, refer to figures 4 and 5
with the windows (g24) to (g35).
- Identify the location of the internal extraction tapes or handles (as per Appendix 4.C.) of the seal keys (o)
and (p) (not shown in the Figure) before removing them.
- Remove cabin windows (g12) to (g23) or (g24) to (g35) Figure 3 or 4 as per Task 56-20-00-051 (MMA).
- Record the cabin window part numbers on the response form in Appendix 4.B.
- As per Figure 5 Sections D-D and E-E:
• Remove the nuts (r), washers (t), screws (u), extraction tapes (w), (x) and (y), inside extraction tapes or
handles (o) and (p) (not shown in the figure) and the press-studs (v).
. Keep the press-studs (v) and the inside extraction tapes or handles (o) and (p).
3.B.2. Removing the PTFE skin (Configurations 1 and 2)
- If installed:
• Remove the PTFE skin (s) from the window frame, using a spatula (zz).
• Discard the PTFE skin (s).
- Clean the window frame using cleaning agent (10) as per Work Card 20-04-01-402 (MTC).
Revision 0  2019-04-10  Page 12/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.3. Measuring the clearance and thickness of each window
3.B.3.a. Thickness measurement principle (Configurations 1 and 2)
- Measure the thickness E of the window at any point on a linear part of the circumference using the
caliper gage (uu):
Window
Linear  Linear
part  part
- Enter the value of E in the response form in Appendix 4.A. for configuration 1 and Appendix 4.B. for
configuration 2.
3.B.3.b. Thickness measurement principle (Configurations 1 and 2)
- Install two collets (vv) vertically on the straight portion of the fuselage aperture and one collet (vv)
horizontally centered as shown in the figure below (step 1).
- Install one collet (vv), horizontally centered, and one collet (vv) vertically centered (step 2).
EXTERNAL VIEW
VV
STEP 1  STEP 2
Revision 0  2019-04-10  Page 13/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
- Install the window in the collets (vv) pushing the window fully into the collets in the direction of the arrows.
- Secure the window using the fasteners (vv1) of the collets (vv).
Window
￾ VV1
WV1
- Measure the clearances J2, J4, J5 and J7 between the structure and the window using the caliper gage
(uu) at 10 mm (.393 in) from the window corner, as shown below.
10 mm  393 in)  Window
J5
J7
J2  J4
- Then measure the clearances J1, J3, J6 and J8 between the structure and the window using the caliper
gage (uu). The measurement must be perpendicular to the structure, as shown below.
J5  J5
J6
CORRECT  INCORRECT
Revision 0  2019-04-10  Page 14/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
J1 J3
Window
J5  J6
J8
J2  J4
- Calculate the average value of the clearances, Jm, (J1+J2+J3+J4+J5+J6+J7+J8)/8 = Jm.
- Enter the value of Jm on the response form in Appendix 4.A. for configuration 1 and in Appendix 4.B. for
configuration 2.
Revision O  2019-04-10  Page 15/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.3.c. Measurement of the clearance and the thickness (Configuration 1)
- Comply with the procedures of paragraphs 3.B.3.a. and 3.B.3.b. on windows (g) to (g11) (Figure 1).
- Check for compliance of Jm and E as per the table below:
Table No. 2
Window location  Compliant average clearance for a  5mm (.196 in) thickness window  Compliant thickness
g or g11
7mm (.275 in) ≤ Um ≤ 10.4mm (.409 in)
g1 or g10
g2 or g9
7 mm (.275 in) ≤ Jm ≤ 10.2 mm (.409 in)  E > 4 mm (.157 in)
93 or g8
94 or g7
7mm (.275 in) ≤ Jm ≤ 10.4mm (.409 in)
95 or g6
3.B.3.d. Measurement of the clearance and the thickness (Configuration 2)
- Comply with the procedures of paragraphs 3.B.3.a. and 3.B.3.b. on windows (g12) to (g23) (Figure 3) or
(924) to (g35) (Figure 4).
- Check for compliance of Jm and E as per the table below:
Window location
(g12 or g23) or (g24 or g35)
(g13 or g22) or (g25 or g34)
(g14 or g21) or (g26 or g33)
(g15 or g20) or (g27 or g32)
(g16 or g19) or (g28 or g31)
(g17 or g18) or (g29 or g30)
Table No. 3
Compliant average clearance for a
6.3mm (.248 in) thickness window  Compliant thickness
7 mm (.275 in) ≤ Jm ≤ 10.4 mm (.409 in)
7 mm (.275 in) ≤ Jm ≤ 10.2 mm (.409 in)
7 mm (.275 in) ≤ Jm ≤ 10 mm (.393 in)  E > 4 mm (.157 in)
7 mm (.275 in) ≤ Jm ≤ 10.2 mm (.409 in)
Revision 0  2019-04-10  Page 16/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.3.e. Interpretation (Configurations 1 and 2)
- Return the response form in Appendix 4.A. or 4.B. to the following address:
https://keycopter.airbushelicopters.com
- Keep a copy of this response form in the aircraft log book.
- If all the clearances Jm and thicknesses E are compliant, continue complying with this ALERT SERVICE
BULLETIN.
- If any clearance Jm and/or thickness E is not compliant with Table No. 2 or 3:
• Contact the Airbus Helicopters Technical Support Department to obtain a technical solution at the
following address: https://keycopter.airbushelicopters.com
• Continue complying with this ALERT SERVICE BULLETIN for windows whose clearance Jm and
thickness E are compliant with Table No. 2 or 3.
NOTE 4
Pending the technical solution proposed by Airbus
Helicopters, for a window with non-compliant clearance um
and/or thickness E, it is acceptable to re-install the window
- a PTFE skin (15),
- the former window seals (a) or (b) or (c) or (d) or (e) or (f) if
they were not damaged during removal or new PRE MOD
- the former seal keys (h) or (j) or (k) or (I) or (m) or (n) if
they were not damaged during removal or new PRE MOD
- the washers (t), extraction tapes (w), (x) and (y), screws (u)
and nuts (r), press-studs (v) and internal extraction tapes
or handles (o) and (p).
3.B.4. Installation of the new window seals (Configurations 1 and 2)
NOTE 5
For configuration 1, only the left side is described (windows
(g) to (g5)), perform the same procedure for the right side
(windows (g6) to (g11)).
NOTE 6
For configuration 2, only the left side is described (windows
(g12) to (g17)) or (windows (g24) to (g29)), perform the
same procedure for the right side (windows (g18) to (g23))
or (windows (g30) to (g35)).
- Cut the window seals (1) to the same length as the previously removed seals (a), (o), (c), (d), (e) and (T),
allowing an excess length of 100 mm (3.94 in.), using tube cutter (yy).
- Clean window seals (1) using cleaning agent (10) and a lint-free cloth as per Work Cards
20-04-01-102 (MTC) and 20-04-01-402 (MTC).
- Check the integrity of window seals (1).
- Install the window seals (1) on the structure and comply with the following installation direction:
• The two moulded ribs (1f) of the window seals (1) must be located outside the helicopter, closest to the
tuselage structure.
. Start the installation of the seals (1) at joint "F" located on the same side of the window as the internal
extraction tape of the seal keys.
• Maintain the seals (1) against the structure using strips of adhesive tape (12) during the installation
Revision 0 2019-04-10  Page 17/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
- Cut off the excess length of window seal (1) using tube cutter (yy):
• Make sure that there is an excess length of 5 to 8 mm (.197 to .315 in.) before completing the seal
installation.
NOTE 7
If there is no excess length, the window seals (1) can retract
and create a gap at joint "F".
- Cut the adhesive tape (12) using the spatula (ww) without damaging the window seal (1), to free the
groove, which is necessary to install the windows.
3.B.5. Window installation
3.B.5.a. Configuration 1 (Figures 1 and 2)
- Install the window extraction tapes (4) using the press-stud (v), flat washers (6) and (9), screw (8), nut (7)
and sealing compound (11) as per Figure 2, Section C-C.
- Tighten the nut (7) to the standard torque.
- Position correctly the window extraction tapes (4) between windows (g), (g1), (94), (g5) and the window
seals (1) before installing the windows as per the photo below.
12
- Position the windows (g) to (g5) in the groove of the window seals (1) as follows:
1/ Position one of the bottom corners of the window in the seal.
2/ Turn the window to position the bottom edge of the window in the seal.
3/ Install the remaining part of the window frame using spatula (zz).
• If necessary, use jerking motions to facilitate installation of the window in the seal.
. During installation, ease the seal over the window using the spatula.
4/ Slide the window (g) to (g5) upwards within the seal (1), to center it correctly.
Revision 0 2019-04-10  Page 18/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
NOTE 8
The window  position  centers within seal (1) during
installation of seal keys (2).
C10
- Make sure that the windows (g) to (g5) are correctly installed in the window seals (1).
- Remove the adhesive tape (12) and discard it.
- Discard the seals (a), (b), (c), (d), (e) and (f), the washers (t), the extraction tapes (W), (x) and (y), the
screws (u) and the nuts (r), if they are not reinstalled as per NOTE 4.
3.B.5.b. Configuration 2 (Figures 3 or 4 and 5)
- Install the window extraction tapes (4) using the press-stud (v), flat washers (6) and (9), screw (16), nut (7)
and sealing compound (11) as per Figure 5, Section D-D.
- Tighten the nut (7) to the standard torque.
- Position correctly the window extraction tapes (4) between the windows (g12), (g17) or (924), (925), (g28)
and (g29) and the window seals (1) before installing the windows as per the photo below.
924
g25
g12 Or  g28
g17  g29
12
Revision 0  2019-04-10  Page 19/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
- Position windows (g12) to (g17) or (g24) to (g29) in the groove of the window seals (1), as follows :
1/ Position one of the bottom corners of the window in the seal.
2/ Turn the window to position the bottom edge of the window in the seal.
3/ Install the remaining part of the window frame using spatula (zz).
• If necessary, use jerking motions to facilitate installation of the window in the seal.
. During installation, ease the seal over the window using the spatula.
4/ Slide windows (g12) to (g17) or (g24) to (g29) upwards within the seal (1) to center it correctly.
NOTE 9
The window position  centers within seal (1) during
installation of seal keys (2).
GIO
- Make sure that the windows (g12) to (g17) or (g24) to (g29) are correctly installed in the window seals (1).
- Remove the adhesive tape (12) and discard it.
- Discard the seals (a), (b), (c), (d), (e) and (f), the washers (t), the extraction tapes (w), (x) and (y), the
screws (u) and the nuts (r), if they are not reinstalled as per NOTE 4.
Revision 0 2019-04-10  Page 20/38
Revision 1 2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 21 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.6. Installation of the seal keys (Configurations 1 and 2)
NOTE 10
Configuration 1: refer to Figures 1 and 2.
Configuration 2: refer to Figures 3 or 4 and 5.
- Cut the internal/external seal keys (2) to the same length as seal keys (h), 1), (k), (1), (m) and (n) previously
removed, allowing an excess length of 100mm (3.94 in.), using the tube cutter (yy).
- Clean seal keys (2) using cleaning agent (10) and a lint-free cloth as per MTC Work Cards 20-04-01-102
and 20-04-01-402.
- Check the integrity of seal keys (2).
- Install the internal extraction tapes (o) and (p) (not shown in the Figure) on the internal seal keys (2).
NOTE 11
It is possible to replace the internal extraction tapes (o) and
(p) with optimized internal extraction handles by complying
with modification 0728136 through Service Bulletin
No 56-006.
- Install the external extraction tapes (3) and (5) on the external seal keys (2).
- Install the seal keys (2) on the window seals (1) using insertion tool (xx) and the
spatula (zz).
. Start the installation at joint "E" or "F" Figure 1 or 3 or 4 as per the instructions given in Notes 12, 13 and
14 below:
NOTE 12
The joint of the internal seal keys (2) must be located
opposite the internal extraction tapes (o) and (p).
NOTE 13
The joint of the external seal keys (2) must be located
opposite the external extraction tapes (3) and (5).
NOTE 14
The internal extraction tapes (o) and (p) (not shown in the
Figure) are located in the same bottom corner of the window
as the external extraction tapes (3) and (5) or in the opposite
bottom corner, as per the helicopter configuration.
Revision 0  2019-04-10  Page 21/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 22 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
. Make sure that the seal keys (2) are installed correctly:
INCORRECT  CORRECT
. Cut off the excess length of the seal keys (2) using tube cutter (yy):
- Keep an excess length of 8mm (.315 in.) before completing the installation of the seal keys.
NOTE 15
If there is no excess length, the seal keys (2) can retract and
create a gap at joint "E" or "F".
- Discard the seal keys (h), i), (k), (I), (m) and (n) if they are not re-installed as per NOTE 4.
3.B.7. Finishing (Figures 1, 2 and 3)
3.B.7.a. Configuration 1 (Figures 1, 2 and 6)
- Mask off the sealing compound application area at joints "E" and/or "F" of the seal keys (2) and the
window seals (1) using adhesive tape (13) (see Figure 6).
- Clean the outlined sealant application area using a cleaning agent (10) and a lint-free cloth, complying
with Work Cards 20-04-01-102 (MTC) and 20-04-01-402 (MTC).
- Sand the outlined sealing compound application area using sandpaper (14).
- Clean, once again, the outlined sealing compound application area using a cleaning agent (10) and a lint-
free cloth, complying with Work Cards 20-04-01-102 (MTC) and 20-04-01-402 (MTC).
- Apply sealing compound (11) as per Work Card 20-05-01-212 (MTC):
. inside joints "E" and/or "F" of seal keys (2).
. inside joints IF'" of window seals (1).
- Apply a bead of sealing compound (11) to cover external joints "E" and "F" of the seal keys (2) and the
window seal (1).
• During application, for the joint of the window seals (1), make sure that the bead of sealing compound
overlaps onto the window and the fuselage structure as indicated in Figure 6.
- As per Figure 6, apply sealing compound (11) at the joints between the internal/external tapes and:
. Windows (g), (g1), (g4) and (g5).
. Window seals (1).
- Remove and discard adhesive tape (13).
- Attach the external key extraction tapes (3) to the window extraction tapes (4) using the self-gripping tape
(4a) on the window extraction tapes (4) as per Figure 2, Section C-C.
- Button the press-studs (3a) on the external extraction tapes (3) onto the press-stud (v) as per Figure 2,
Section C-C.
- Button the press-studs (5a) on the external extraction tapes (5) onto the press-stud (q) as per Figure 2,
Section D-D.
Revision 0 2019-04-10  Page 22/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 23 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.B.7.b. Configuration 2 (Figures 3 or 4 and 5 and 6)
- Mask off the sealing compound application area at joints "E" and/or "F" of the seal keys (2) and the
window seals (1) using adhesive tape (13) (see Figure 6).
- Clean the outlined sealant application area using a cleaning agent (10) and a lint-free cloth, complying
with Work Cards 20-04-01-102 (MTC) and 20-04-01-402 (MTC).
- Sand the outlined sealing compound application area using sandpaper (14).
- Clean, once again, the outlined sealing compound application area using a cleaning agent (10) and a lint-
free cloth, complying with Work Cards 20-04-01-102 (MTC) and 20-04-01-402 (MTC).
- Apply sealing compound (11) as per Work Card 20-05-01-212 (MTC):
• inside joints "E" and/or "F" of seal keys (2).
inside joints F"" of window seals (1).
- Apply a bead of sealing compound (11) to cover external joints "E" and "F" of the seal keys (2) and the
window seal (1).
• During application, for the joint of the window seals (1), make sure that the bead of sealing compound
overlaps onto the window and the fuselage structure as indicated in Figure 6.
- As per Figure 6, apply sealing compound (11) at the joints between the internal/external tapes and:
. Windows (g12) and (g17) or (g24), (g25), (928) and (g29).
• Window seals (1).
- Remove and discard adhesive tape (13).
- Attach the external key extraction tapes (3) to the window extraction tapes (4) using the self-gripping tape
(4a) on the window extraction tapes (4) as per Figure 5, Section D-D.
- Button the press-studs (3a) on the external extraction tapes (3) onto the press-stud (v) as per Figure 5,
Section D-D.
- Button the press-studs (5a) (not shown in the Figure) on the external extraction tapes (5) onto the press-
stud (q) (not shown in the Figure).
3.B.8. Final steps (Configurations 1 and 2)
- Install all the coverings previously removed.
- Perform a check of the clearance between the seals and the cabin coverings as per
Task 56-20-00-212 (MMA).
- Perform an appearance check on aircraft after inspection or repair as per MTC Work Card 20-07-03-408.
- Connect all electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Remove the access equipment.
Revision O  2019-04-10  Page 23/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 24 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
3.C. RECORD OF COMPLIANCE
Compliance with this document:
Record compliance with this ALERT SERVICE BULLETIN, with the revision number, in the helicopter
documents when all the jettisonable window seals have been replaced.
Tracking of modifications in the documentation:
Configuration 1
Record embodiment of modification 0728370 in the helicopter documents when all the jettisonable window
seals have been replaced.
Configuration 2
For helicopters (S/N) 2648, 2718 and 2731, record embodiment of modification 332P087142.00 in the
helicopter documents when all the jettisonable window seals have been replaced.
For helicopters (S/N) 2885 and 2901, record embodiment of modification 332P087142.03 in the helicopter
documents when all the jettisonable window seals have been replaced.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
After application of this ALERT SERVICE BULLETIN, refer to the Master Servicing Manual (MSM) in effect
for maintenance intervals.
Revision O  2019-04-10  Page 24/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 25

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 25/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 1 
 
a 
b 
e 
f 
1 
c 
d 
1 
(See Figure 2) 
(See Figure 2) 
g g2 g3 g4 g5 g6 g7 g8 g9 g10 
0 g11 g1 
g 
g1 
g4 
g5 
g6 
g7 
g10 
g11 
g2 
g9 
g3 
g8 
F 
F F 
h 
j 
m 
n 
2 
k 
2 
l 
2 
E 
E 
E 
11 
11 
11 
11

### Page 26

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 26/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 27

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 27/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2 
1f 
(See Figure 1) (See Figure 1) 
a 
b 
e 
f 
1 
1f 
c 
d 
1 
OUTSIDE INSIDE 
OUTSIDE INSIDE 
w 
4 
v 
t 
6 
11 
9 
u 
8 
r 
7 
h 
j 
m 
n 
2 
h 
j 
m 
n 
2 
k 
l 
2 
k 
l 
2 3a 
y 
5 
4a 
5a 
x 
3 
g 
g1 
g4 
g5 
g6 
g7 
g10 
g11 
g2 
g3 
g8 
g9 
q

### Page 28

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 28/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 29

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 29/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 3 
g12 g14 g15 g16 g17 g18 g19 g20 g21 g22 g23 g13 
Or  Or  Or  Or  
g12 
g17 
g18 
g23 
g13 
g14 
g15 
g16 
g19 
g20 
g21 
g22 
k 
2 
l 
2 
h 
j 
m 
n 
2 
a 
b 
e 
f 
1 
c 
d 
1 
E F F E E F 
(See Figure 5) 
(See Figure 5) 
(See Figure 5) 
11 
11 
11 
11

### Page 30

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 30/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 31

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 31/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4 
g24 g26 g27 g28 g29 g30 g31 g32 g33 g34 g35 g25 
Or  Or  Or  Or  Or  Or  Or  Or  
g24 
g25 
g28 
g29 
g30 
g31 
g34 
g35 
h 
j 
m 
n 
2 
a 
b 
e 
f 
1 
11 
(See Figure 5) 
(See Figure 5) 
11 
g26 
g27 
g32 
g33 
k 
l 
2 
c 
d 
1 
11 
11 
(See Figure 5) 
E F F E 
F 
E

### Page 32

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 32/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 33

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 33/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 5 
(See Figure 3 or 4) 
(See Figure 3 or 4) 
t 
6 
r 
7 
u 
16 
w 
4 
x 
3 
y 
5 
INSIDE OUTSIDE 
OUTSIDE 
INSIDE 
v 
1f 
1f 
11 
9 
h 
j 
m 
n 
2 
k 
l 
2 
k 
l 
2 
a 
b 
e 
f 
1 
c 
d
1 
4a 
3a 
g12 
g17 
g18 
g23 
g13 
g14 
g15 
g16 
g19 
g20 
g21 
g22 
g26 
g27 
g32 
g33 
Or Or 
g24 
g25 
g28 
g29 
g30 
g31 
g34 
g35 
Or 
Or 
Or 
Or 
k 
l 
2 
h 
j 
m 
n 
2 
Or 
k 
l 
2 
h 
j 
m 
n 
2 h 
j 
m 
n 
2 
c 
d
1 
Or 
a 
b 
e 
f 
1

### Page 34

ASB No. EC225-56A013 
Revision 0    2019-04-10   Page 34/38 
Revision 1    2020-02-10  This document is available on the Internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 35 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
> 11
1 mm  mm
(039 in  (.039 In.
11
Figure 6
Revision 0  2019-04-10  Page 35/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 36 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
4. APPENDIX
4.A. APPENDIX: Information sheet for helicopters equipped with 5mm thickness windows
ALERT SERVICE BULLETIN Response Form
No. 56A013
Fill in the form and return it by email:
Airbus Helicopters - Etablissement de Marignane
Customer Support
https://keycopter.airbushelicopters.com
Keep a completed copy of this response form in the aircraft Log Book.
Date:
Customer (Name):
Helicopter:
Type: .
Version:
Serial Number:
Total flying hours
Aircraft location:
Country:
Main base:
Over water operations: YES / NO
Measurement of the clearance and the thickness of the windows (specify the unit of measurement):
Window  Window Part  Calculation  clearance  Average  Thickness
location  Number (P/N)  (Jm)  (E)
g
g1
92
g3
94
g5  (U1+J2+J3+J4+J5+J6+J7+J8)/8 =
g6  Jm
98
99
g10
g11
Remarks:
Date:  Signature:
Please make a copy of this page. The original form must remain in the ALERT SERVICE BULLETIN.
Revision 0  2019-04-10  Page 36/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 37 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
4.B. APPENDIX: Information sheet for helicopters equipped with 6.3mm thickness windows
ALERT SERVICE BULLETIN Response Form
No. 56A013
Fill in the form and return it by email:
Airbus Helicopters - Etablissement de Marignane
Customer Support
https://keycopter.airbushelicopters.com
Keep a completed copy of this response form in the aircraft Log Book.
Date:
Customer (Name):
Helicopter:
Type:
Version
Serial Number:
Total flying hours
Aircraft location:
Country:
Main base:
Over water operations: YES / NO.
Measurement of the clearance and the thickness of the windows (specify the unit of measurement):
Window  Window Part  Calculation  clearance  Average  Thickness
location  Number (P/N)  (Jm)  (E)
g12 or g24
913 or g25
g14 or g26
915 or g27
916 or g28
g17 or g29
g18 or g30  = Jm
g19 or 931
920 or g32
g21 or g33
922 or g34
g23 or g35
Remarks:
Date:  Signature:
Please make a copy of this page. The original form must remain in the ALERT SERVICE BULLETIN
Revision 0  2019-04-10  Page 37/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

### Page 38 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A013
4.C. APPENDIX: Internal extraction
Depending on the helicopter configuration, the internal key extraction function can be provided by an
extraction handle or an extraction tape, the schematic diagrams of which are shown below:
SECTION
e-e
INSIDE  SECTION
F-F
INSIDE
OUTSIDE
Extraction
handle
OUTSIDE  Extraction
tape
Revision O  2019-04-10  Page 38/38
Revision 1  2020-02-10  This document is available on the Internet:www.airbushelicopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
