# Airbus Helicopters Alert Service Bulletin EC225-56A016

Copy: No revision named ("Airbus Helicopters ASB No. EC225-56A016 Rev 0"), 28 pages: PDF https://openairdocs.org/files/sha256/a0/3a/a03a2ede7d9b5f6810c63203cede908f5555d6c763f065e1b564fa994705ff89; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a016/file/a03a2ede7d9b.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0160, the docket of AD 2023-08-06. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-56A016
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a016

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-08-06](https://openairdocs.org/ad/2023-08-06.md), effective Jun 22, 2023: No revision named
- [AD 2020-20-08](https://openairdocs.org/ad/2020-20-08.md), effective Dec 11, 2020: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec225-56a016/proposed.md).

## Text (28 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0160, the docket of AD 2023-08-06. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
Civil version: LP
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
WINDOWS - Cabin jettisonable windows
Improvement to the window jettisoning system
Corresponds to modification 332A087149.00
For the attention of
Revision No.  Date of issue
Revision 0  2020-02-10
Summary:
This ALERT SERVICE BULLETIN consists in further improving the jettisoning of the windows from inside the cabin,
by replacing the instructions provided in ALERT SERVICE BULLETIN No.05A046.
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Helicopters: 2663, 2666, 2670, 2673
Revision 0 2020-02-10  Page 1/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
On EC225 helicopters with serial numbers (S/N) indicated on page 1.
1.A.2. Non-installed equipment or parts
On removable doors and panels.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Airbus Helicopters introduced a protective measure through ALERT SERVICE BULLETIN No.05A046, which
consisted in installing a PTFE skin between the frame and the seal of jettisonable windows, to reduce the
force required for jettisoning.
Airbus Helicopters has developed an improvement which consists in removing the PTFE skin and installing
silicone window seals instead of the polychloroprene seals currently installed on the helicopter cabin
windows.
This ALERT SERVICE BULLETIN cancels the instructions of ALERT SERVICE BULLETIN No.05A046.
Airbus Helicopters makes it mandatory to comply with this ALERT SERVICE BULLETIN.
Revision O  2020-02-10  Page 2/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists in:
Bubble window
Small windows
Small window
Large windows
- Removing, if installed, the PTFE skin present between the frame and the seal of the cabin windows.
- Measuring the thickness of each window (except the small windows and the bubble windows).
- Replacing small windows and the bubble windows.
- Measuring the clearance between each window and the structure.
- Replacing the seals of the cabin windows by silicone seals.
- Returning the response sheet.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
The work must be performed on the helicopter by the operator.
Helicopters/installed equipment or parts:
Helicopters which do not operate over water:
Comply with paragraph 3. within 250 flight hours or 6 months (the first limit reached is applicable) from
receipt of this ALERT SERVICE BULLETIN, issued on the date indicated in the page footer.
Helicopters which operate over water:
Comply with paragraph 3. within 110 flight hours or 6 months (the first limit reached is applicable) from
receipt of this ALERT SERVICE BULLETIN, issued on the date indicated in the page footer.
Non-installed equipment or parts:
Comply with paragraph 3 of this ALERT SERVICE BULLETIN before installation on the helicopter.
Revision 0 2020-02-10  Page 3/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
1.F. APPROVAL
Approval of modifications:
The information or instructions relate to modification 332A087149.00 which was approved
on January 31, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision O was approved on
February 03, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following staff
qualifications:
Qualification: - 1 Airframe Technician to remove the PTFE skin,
- 2 Airframe Technicians to remove/install the windows.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours: - 2 hours per window for 2 Airframe Technicians.
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter
configuration.
Helicopter downtime is estimated at 6 days including the time to remove/install the linings.
1.H. WEIGHT AND BALANCE
Weight: +3.824 kg
Longitudinal moment: +19.88 m.kg.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
Revision 0 2020-02-10  Page 4/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
1.K. REFERENCES
The following documents are required for compliance with this ALERT SERVICE BULLETIN.
Standard Practices Manual (MTC):
- MTC: 20-02-05-404: Assembly by screws and nuts - Joining
- MTC: 20-04-01-102: Use of cleaning products on individual parts and on helicopters - Cleaning
- MTC: 20-04-01-402: Cleaning of removed individual parts with liquid solvents - Cleaning
- MTC: 20-05-01-212: Implementation of Sealing compound CM 6232 - General sealing procedures
- MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems - Technical instructions
- MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions
Aircraft Maintenance Manual (MMA):
- MMA: 56-20-00-051: Removal-Installation - CABIN WINDOWS
- MMA: 56-20-00-212: Checking clearance between jettisonable window seal and cabin upholstery - CABIN
WINDOWS
1.L. OTHER AFFECTED PUBLICATIONS
The modification will be included in the:
- Illustrated Parts Catalog (IPC),
- Aircraft Maintenance Manual (MMA).
The MMA will be updated during a future revision.
Revision of the IPC documents must form the subject of the customer's order.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
PRE MOD and POST MOD seals are not interchangeable.
PRE MOD and POST MOD seal keys are not interchangeable.
Mixability:
Mixing between PRE MOD window assemblies (seal, seal keys and PTFE skin) and POST MOD window
assemblies (seal and seal keys) on the same helicopter is authorized.
Revision 0 2020-02-10  Page 5/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For any information on the price of modification kits and/or components, contact the Airbus Helicopters
Network Sales and Customer Relations Department.
Availability
Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's
request.
Procurement
Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters
Etablissement de Marignane
Direction des Ventes et Relation Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
For any information, contact the Sales and Customer Relations Department.
Revision 0 2020-02-10  Page 6/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
NOTE 3
The components listed in the following kit do not necessarily
all have to be used for the modification of the helicopter.
Kit to be ordered for one helicopter:
New P/N  Old
Key Word  Qty  Item
P/N  →→  Instruction
85D seal kit for  332A08-7149-0071
5mm windows
Silicone 85D  151601505M  1
window seal  (704A39-8210-66)
Silicone 85D  2  151601506N  2
window seal key  (704A39-8210-67)
Key extraction tape  6  332A23-0520-04  З
Window extraction  6  332A23-0520-07  4
tape
Single key  8  332A23-0520-06  5
extraction tape
Flat washer  10  23111AG04OLE  6
Self-locking nut  10  ASN52320BH040N  7
Flat washer  10  23112AG04OLE  9
Mushroom head  4  A0099BC040012L  16
screw
Mushroom head  A0099BC040016L  20
screw
Equipment or parts to be ordered separately:
New P/N  Old
Key Word  Qty  Item
P/N  →  Instruction
5 mm bubble  2  332P22-2001-21  17  332P22-2001-20
windows
5 mm colorless  6  332A22-1201-40  18  332A22-1201-20
window
Revision 0  2020-02-10  Page 7/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
Consumables to be ordered separately:
As per Work Cards and Tasks indicated in this ALERT SERVICE BULLETIN and list below:
Key Word  Qty  PAN  Item
Cleaning agent  AR N8955004956  232  10
(Gasoline G)
Or
Petrol ether  AR  Off the shelf  10
Sealing compound  AR  ECS 6046-1198  6232  11
Cloth adhesive tape  AR  Type 3M 22888 or equivalent  12
Adhesive tape  AR  DHS171-143.21  6229  13
Abrasive paper, 80-grit  AR Off the shelf  14
PTFE skin  AR SCOTCH PTFE 5480 - 25,4 MM  15
Consumables can be ordered separately from the following companies:
Aviatec Global Aviation
Website: www.aviatec.net
Telephone: +33 1.34.46.45.24 or +49 4193 8803 630
Fax: +33 1.34.46.45.26 or +49 4193 8803 699
AOG: +49 4193 8803 660
AOG email: aog@aviatec.aero
BDSI
Website: www.boeingdistribution.com
Telephone: +1.305.925.2600
Fax: +1.305.507.7191
AOG: +1.305.471.8888
AOG email: AOGdesk@Boeingdistribution.com
Gaches Chimie
Website: www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
Revision O  2020-02-10  Page 8/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
Special tools:
Key Word  Qty  Tool P/N or equivalent  Item
Tool kit  KA6420
Rounded end spatula  770150225 (commercial P/N)  ZZ
Tube cutter  Off the shelf (Virax 215032)
Insertion tool  Off the shelf (LT 415)  XX
Curved spatula  1479N/S5 ("Beta" supplier P/N)  ww
Key Word  Qty  Tool P/N or equivalent  Item
Measurement kit  332A98-8701-00
Clamp  5  Thickness: 8 mm  WV
Key Word  Qty  Tool P/N or equivalent  Item
Digital vernier  Off the shelf
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision O  2020-02-10  Page 9/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
As per Work Card 20-02-05-404 (MTC), read and comply with the instructions concerning assembling by
screws and nuts.
3.B. WORK STEPS
NOTE 1
The installation of the new seals (1) and the seal keys (2)
must be performed dry.
Compliance with the work steps concerned with the installation of the seals is described in a video which is
accessible by following the link below:
http://dai.ly/k3DklgBuVI85w|pfkm2
3.B.1. Preliminary steps
- Disconnect all the electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Install the access equipment.
- Remove all coverings to enable adequate access to the various work areas.
- Mark the locations of the seal key internal extraction tapes or handles (as per Appendix 4.B.) (o) and (p)
(not shown in the figure) before removing them.
- Remove the cabin windows (g) to (g11) Figure 1, as per Task 56-20-00-051 (MMA).
- Replace the windows (g1), (g2), (g4), (g7), (g9) and (g10) with the new bubble windows (18).
- Replace the windows (g3) and (g8) with the new bubble windows (17).
- Record the P/Ns of the cabin windows on the response sheet in Appendix 4.A.
- As per Figure 2 Sections E-E, F- F and G-G.
• Remove the nuts (r), the washers (t), the screws (u), the external extraction tapes (w), (x) and (y), the
internal extraction tapes or handles (o) and (p) (not shown in the figure) and the snap fasteners (v)
and (q).
• Keep the snap fasteners (v) and (q) and the internal extraction tapes or handles (o) and (p).
Revision O  2020-02-10  Page 10/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.B.2. Removal of the PTFE skin
- If installed:
• Remove the PTFE skin (s) from the window frame, using a spatula (zz).
. Discard the PTFE skin (s).
- Clean the window frame using cleaning agent (10), as per Work Card 20-04-01-402 (MTC).
3.B.3. Measurement of the clearance and thickness of the windows
3.B.3.a. Thickness measurement principle
- Measure the window thickness E at a point on a straight section of the periphery using the vernier (uu):
Window
Straight  section  - section  Straight
- Record the value of E on the response sheet in Appendix 4.A.
Revision 0  2020-02-10  Page 11/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.B.3.b. Clearance measurement principle
- Install two clamps (vv) vertically on the straight section of the structure and one clamp (vv) centered
horizontally as shown on the figure below (step 1).
- Install one clamp (w) centered horizontally and one clamp (wv) centered vertically (step 2).
EXTERNAL VIEW
STEP 1  STEP 2
- Install the window against the clamps (vv) as shown by the arrows.
- Immobilize the window with the fasteners (vv1) of the clamps (VV).
Window
vv1
VV1
Revision 0 2020-02-10  Page 12/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
- Measure the clearances J2, J4, J5 and J7 between the structure and the window using the
vernier (uu) 10 mm (0.393 in) from the corner of the window as shown below.
10 mm  \(.393 in)  Window
J5
J7
J2  J4
- Then measure the clearances J1, J3, J6 and J8 between the structure and the window using the
vernier (uu); the measurement must be perpendicular to the structure as shown below.
Window
J5  _ J6  J5
J6
CORRECT  INCORRECT
J1  J3
Window
J5  J6
J8
J2  J4
- Calculate the average clearance Jm, (J1+J2+J3+J4+J5+J6+J7+J8)/8 = Jm.
- Record the value of Jm on the response sheet in Appendix 4.A.
Revision 0 2020-02-10  Page 13/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.B.3.c. Measurement of the clearance and thickness
- Comply with the procedure of paragraph 3.B.3.a. for windows (g), (g5), (g6) and (g11) (Figure 1).
• Comply with the procedure of paragraph 3.B.3.b. for windows (g), (g5), (g6), (g11), (17) and (18)
(Figure 1).
- Check the compliance of Jm and E as per table No. 1 below:
Table No.1
Window reference  Average clearance compliant  Thickness compliant
(g) or (g11)
(18) in place of (g1) or (g10)
(18) in place of (g2) or (g9)
(17) in place of (g3) or (g8)
(18) in place of (g4) or (g7)
(g5) or (g6)
E > 4 mm (.157 in)
7 mm (.275 in) ≤ Jm ≤ 10.4 mm (.409 in)
7 mm (.275 in) ≤ Jm ≤ 10.2 mm (.401 in)  Not applicable
7 mm (.275 in) ≤ Jm ≤ 10.4 mm (.409 in)
E > 4 mm (.157 in)
3.B.3.d. Interpretation
- Return the response sheet in Appendix 4.A:
https://keycopter.airbushelicopters.com
- Keep a copy of this response sheet in the Aircraft Log Book.
- If all the Jm clearances and E thicknesses are compliant, continue to comply with this ALERT SERVICE
- If any of the Jm clearances and/or E thicknesses are not compliant with Table No.1:
• Contact the Airbus Helicopters Technical Support Department at the following address to obtain a
technical solution: https://keycopter.airbushelicopters.com
• Continue to comply with this ALERT SERVICE BULLETIN for the windows whose Jm clearance and E
thickness are compliant with Table No 1.
NOTE 2
Pending the technical solution proposed by Airbus
Helicopters, a window whose Jm clearance and/or E
thickness is not compliant can be reinstalled with:
- a PTFE skin (15),
- the old window seals (a) or (b) or (c) or (d) or (e) or (f), if
not damaged during removal, or new PRE MOD seals,
- the old seal keys (h) or i) or (k) or (I) or (m) or (n), if not
damaged during removal or new PRE MOD seal keys,
- the washers (t), the external extraction tapes (w), (x)
and (y), the screws (u) and the nuts (r), the snap
fasteners (v) and (q) and the internal extraction tapes or
handles (o) and (p).
Revision 0 2020-02-10  Page 14/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.B.4. Installation of the new window seals
NOTE 3
To install the seals, the windows and the seal keys (as per
paragraphs 3.B.4., 3.B.5., 3.B.6. and 3.B.7.), only the LH
side is described (window positions g to g5), repeat the work
steps for the RH side (window positions g6 to g 11).
- Cut the window seals (1) to the length of the previously removed seals (a), (b), (c), (d), (e) and (f), with an
excess length of 100 mm (3.94 in), using the tube cutter (Vy).
- Clean the window seals (1) using cleaning agent (10) and a lint-free cloth, as per
Work Cards 20-04-01-102 and 20-04-01-402 (MTC).
- Check the integrity of the window seals (1).
- Install the window seals (1) on the structure and comply with the following installation direction:
• The two lips (1f) of the window seals (1) must be installed outside the helicopter, on the side of the
structure.
. Start the installation of the seals (1) at the joint "F" located on the same side of the window as the
internal seal key extraction tape.
. Secure the seals (1) to the structure using adhesive tape (12) during the installation phase.
- Trim the excess length of the window seals (1), using the tube cutter (yy):
. Keep an excess length of 5 to 8 mm (0.197 to 0.315 in) before the completion of the installation of the
seals.
NOTE 4
If there is no excess length, the window seals (1) can shrink
and create a gap at the joint "F".
- Cut the adhesive tape (12) using the spatula (ww) without damaging the window seals (1), to free the
groove, which is necessary to install the windows.
3.B.5. Installation of the windows
- Install the window extraction tapes (4) using the snap fastener (v), the flat washers (6) and (9), the
screw (20), the nut (7) and sealing compound (11) as per Figure 2, Section E-E.
- Tighten the nut (7) to standard torque.
- Install the snap fasteners (q) using the flat washers (6) and (9), the screw (16), the nuts (7) and sealing
compound (11) as per Figure 2, Section G-G.
- Tighten the nut (7) to standard torque.
Revision 0 2020-02-10  Page 15/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
- Position the window extraction tapes (4) correctly between the windows (g) and (g5) and the window
seals (1) before installing the windows as per the photograph below.
g5
12
- Position the windows (g), (18) in place of the windows (g1) and (g2), (17) in place of the window (g3),
(18) in place of the window (g4) and (g5) in the groove of the window seals (1), as follows:
1/ Position one of the bottom corners of the window in the seal.
2/ Rotate the window to position the bottom edge of the window in the seal.
3/ Install the remaining part of the window frame using spatula (zz).
• If necessary, use jerking motions to facilitate installation of the window in the seal.
. During installation, ease the seal over the window using the spatula.
4/ Slide the window upwards in the seal to center it correctly.
NOTE 5
The window position centers in the seal (1) during
installation of the seal keys (2).
Revision 0 2020-02-10  Page 16/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
- Make sure that the windows (g), (18) in place of the windows (g1) and (g2), (17) in place of the
window (g3), (18) in place of the window (94) and (g5) are correctly installed in the window seals (1).
- Remove and discard the adhesive tape (12).
- Discard the seals (a), (b), (c), (d), (e) and (f), the small windows (g1), (g2) and (g4), the bubble
windows (g3), the washers (t), the external extraction tapes (w), (x) and (y), the screws (u) and the nuts (r),
if not reinstalled as per NOTE 2.
3.B.6. Installation of the seal keys
- Cut the internal/external seal keys (2) to the length of the previously removed seal keys (h), I), (k), (I), (m)
and (n), with an excess length of 100 mm (3.94 in), using the tube cutter (Vy).
- Clean the seal keys (2) using cleaning agent (10) and a lint-free cloth as per Work Cards 20-04-01-102 and
20-04-01-402 (MTC).
- Check the integrity of seal keys (2).
- Install the external extraction tapes (o) and (p) (not shown on the figure) on the internal seal keys (2).
NOTE 6
The internal extraction tapes (o) and (p) can be replaced by
optimized internal extraction handles by complying with
modification 0728136 through Service Bulletin No.56-006.
- Install the external extraction tapes (3) and (5) on the external seal keys (2) as per Figure 2,
Sections E-E, F-F and G-G
- Install the seal keys (2) on the window seals (1) using the insertion tool (xx) and the spatula (zz).
Revision O  2020-02-10  Page 17/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
. Start the installation at the joint "E" or "F" Figure 1, Details A and B, and Figure 3, Details C and D as per
the instructions of notes 7, 8 and 9 below:
NOTE 7
The joint of the internal seal keys (2) must be located
opposite the internal extraction tapes (o) and (p).
NOTE 8
The joint of the external seal keys (2) must be located
opposite the external extraction tapes (3) and (5).
NOTE 9
The internal extraction tapes (o) and (p) (not shown on the
figure) are located in the same bottom corner of the window
as the external extraction tapes (3) and (5) or in the opposite
bottom corner, depending on the helicopter configuration.
. Make sure that the seal keys (2) are installed correctly:
INCORRECT  CORRECT
. Trim the excess length of the seal keys (2), using the tube cutter (Vy):
- Keep an excess length of 8 mm (0.315 in) before the completion of the installation of the seal keys.
NOTE 10
If there is no excess length, the seal keys (2) can shrink and
create a gap at joint "E" or "F".
- Discard the seal keys (h), (i), (k), (I), (m) and (n) if not reinstalled as per NOTE 2.
Revision 0 2020-02-10  Page 18/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.B.7. Finishing (Figures 1, 2 and 3)
- Mark out the sealing compound application area at the joints "E" and/or "F" of the seal keys (2) and of the
window seals (1) using adhesive tape (13) (see Figure 4).
- Clean the sealing compound application area using cleaning agent (10) and a lint-free cloth, as per Work
Cards 20-04-01-102 and 20-04-01-402 (MTC).
- Sand the sealing compound application area using abrasive paper (14).
- Clean the sealing compound application area again using cleaning agent (10) and a lint-free cloth, as per
Work Cards 20-04-01-102 and 20-04-01-402 (MTC).
- Apply sealing compound (11) as per Work Card 20-05-01-212 (MTC) inside:
• Joints "E" and/or "F" of the seal keys (2).
. Joints "F" of the window seals (1).
- Apply a bead of sealing compound (11) to cover the external joints "E" and "F" of the seal keys (2) and of
the window seals (1).
• During application, for the joint of the window seals (1), make sure that the bead of sealing compound
overlaps the window and the structure as indicated in Figure 4.
- As per Figure 4, apply sealing compound (11) at the joints between the external tapes and:
. The windows (g), (g5), (g6) and (g11).
. The window seals (1).
- Remove and discard the adhesive tape (13).
- Attach the external key extraction tapes (3) to the window extraction tapes (4) using the self-gripping tape
(4a) present on the window extraction tapes (4) and as per Figure 2, Section E-E.
- Press the snap fasteners (3a) present on the external extraction tapes (3) together with the snap
fastener (v) as per Figure 2, Section E-E.
- Press the snap fasteners (5a) present on the external extraction tapes (5) together with the snap
fastener (q) as per Figure 2, Section F-F and G-G.
- Install again the internal extraction tapes or handles previously removed during compliance with
paragraph 3.B.1.
3.B.8. Final steps
- Install all the linings previously removed.
- Check the clearance between the seals and the cabin linings as per Task 56-20-00-212 (MMA).
- Perform an appearance check on the helicopter after inspection or repair as per Work Card
20-07-03-408 (MTC).
- Connect all the electrical power supplies as per Work Card 20-07-03-406 (MTC).
- Remove the access equipment.
Revision 0  2020-02-10  Page 19/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. EC225-56A016
3.C. RECORD OF COMPLIANCE
Compliance with this document:
Record compliance with this ALERT SERVICE BULLETIN, with the revision number, in the helicopter
documents, when all the jettisonable window seals have been replaced.
Tracking of modifications in the documentation:
Record embodiment of modification 332A087149.00, in the helicopter documents, when all the jettisonable
window seals have been replaced
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
After compliance with this ALERT SERVICE BULLETIN, refer to the Master Servicing Manual (MSM) in
effect for maintenance intervals.
Revision 0  2020-02-10  Page 20/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 21

ASB N° EC225-56A016 
Revision 0    2020-02-10   Page 21/28 
      This document is available on the internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 1 
Return to paragraphs 3.B.1. , 3.B.3.c. , 3.B.6.  
 
F F E E 
g 
g5 
g6 
g11 
g1 
g4 
g7 
g10 
18 
a 
f 
1 
b 
e 
1 
j 
m 
2 
h 
n 
2 
11 
11 
 11 
(See Figure 2) 
(See Figure 2) 
(See Figure 3) (See Figure 3) 
g g2 
18 
g3 
17 
g4 
18  
g5 g6 g7 
18 
g8 
17 
g9 
18 
g10 
18 g11 g1 18

### Page 22

ASB N° EC225-56A016 
Revision 0    2020-02-10   Page 22/28 
      This document is available on the internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT INTENTIONALLY BLANK

### Page 23

ASB N° EC225-56A016 
Revision 0    2020-02-10   Page 23/28 
      This document is available on the internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Return to paragraphs 3.B.1. , 3.B.5. , 3.B.6. , 3.B.7.  
Figure 2 
(See Figure 1) 
(See Figure 3) 
t 
6 
r 
7 
u 
20 
w 
4 
x 
3 
y 
5 
INSIDE OUTSIDE 
OUTSIDE 
INSIDE 
v 
1f 
1f 
11 
9 
4a 
3a 
g2 
g3 
g8 
g9 
17 Or 18 
g 
g5 
g6 
g11 
a 
f 
1 
h 
n 
2 h n 
2 
c 
d 
1 
k 
l 
2 
k 
l 
2 
(See Figure 1) 
t 
6 
r 
7 
u 
16 
y 
5 
q 
1f 
5a 
g1 
g4 
g7 
g10 
18 
9 
11 
b 
e 
1 
j 
m 
2 
j 
m 
2 
INSIDE 
OUTSIDE

### Page 24

ASB N° EC225-56A016 
Revision 0    2020-02-10   Page 24/28 
      This document is available on the internet: www.airbushelicopters.com/techpub  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT INTENTIONALLY BLANK

### Page 25 (OCR)

AIRBUS
HELICOPTERS  ASB N° EC225-56A016
g3
17
92
18
(See Figure 2) Fa
2
(See Figure 1)  g9
18
17
(See Figure 2) F y
(See Figure 2) pl
2  2
Return to paragraph 3.B.6.
Figure 3
Revision 0 2020-02-10  Page 25/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 26 (OCR)

AIRBUS
HELICOPTERS  ASB N° EC225-56A016
> 11
1 mm  1 mm
(039 in.)  (.039 in.)
Return to paragraph 3.B.7.
Figure 4
Revision 0 2020-02-10  Page 26/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 27 (OCR)

AIRBUS
HELICOPTERS  ASB N° EC225-56A016
4. APPENDIX
4.A. APPENDIX: Information sheet for helicopters serial numbers (S/N) indicated on page 1.
ALERT SERVICE BULLETIN Response Form
No. 56A016
Complete the form and return it by email:
Airbus Helicopters - Etablissement de Marignane
Customer Support
https://keycopter.airbushelicopters.com
Keep a completed copy of this response sheet in the Aircraft Log Book.
Date:
Customer (Name):
Helicopter:
Type: EC225
Version: LP
Serial Number:
Total flying hours
Aircraft location:
Country:
Main base
Off-shore flight: YES/ NO
Measurement of the clearance and the thickness of the windows (specify the measurement unit):
Window  Number (P/N)  Window Part  Calculation  clearance  Average  Thickness (E)
position  (Jm)
g
g1
332A22-1201-40
g2  Not applicable
93  332P22-2001-21
g4  332A22-1201-40
g5  (J1+J2+J3+J4+J5+J6+J7+J8)/8
96  = Jm
332A22-1201-40
98  332P22-2001-21
910  g9  332A22-1201-40  Not applicable
g11
Remarks:
Date:  Signature:
Please make a copy of this page. The original form must remain in the ALERT SERVICE BULLETIN.
Revision 0 2020-02-10  Page 27/28
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 28 (OCR)

AIRBUS
HELICOPTERS  ASB N° EC225-56A016
4.B. APPENDIX: Internal extraction
Depending on the helicopter configuration, the internal key extraction function can be performed by an
extraction handle or tape whose schematic diagrams are shown below:
SECTION
e-e
INSIDE  SECTION
F-F
INSIDE
OUTSIDE
Extraction
handle
OUTSIDE  Extraction
tape
Revision 0 2020-02-10  Page 28/28
This document is available on the internet: www.airbushelicopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
