# Airbus Helicopters Alert Service Bulletin EC225-56C012

Copy: No revision named ("Airbus Helicopters ASB EC225-56C012 Rev 0"), 19 pages: PDF https://openairdocs.org/files/sha256/37/e4/37e47461bd59272e818b57cfc43ee2dd7f3ebd2bd559adf922e10de4a9169c4b; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-56c012/file/37e47461bd59.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2019-1019; AD 2020-20-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-56C012
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-56c012

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-20-08](https://openairdocs.org/ad/2020-20-08.md), effective Dec 11, 2020: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/ec225-56c012/proposed.md).

## Text (19 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2019-1019; AD 2020-20-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
Civil version: LP
ALERT SERVICE BULLETIN
CORRECTIVE MEASURE
WINDOWS - Cabin windows
Improvement to VIP window jettisoning
Corresponds to modification 332P087140.00
For the attention of
Revision No.  Date of issue
Revision 0  2018-02-08
Summary:
This ALERT SERVICE BULLETIN consists of improving the jettisoning of VIP windows from inside the cabin, by
replacing the instructions defined in ALERT SERVICE BULLETIN No. EC225-05A046 for helicopters with a Serial
Number (S/N) specified in the page footer.
Compliance:
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory.
Helicopter S/Nos.: 2600, 2623, 2645, 2650, 2651, 2653, 2659, 2684, 2693, 2711, 2712, 2719, 2753, 2756,
2767, 2796, 2926, 2961, 2973, 2974, 2979, 3002, 3003, 3012
Revision 0 2018-02-08  Page 1/19
This document is available on the internet: www.airbushe  e//copters.com/techpub

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
EC225 helicopters with a Serial Number (S/N) listed on page 1.
1.A.2. Non-installed equipment or parts
On removable panels and doors.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. PURPOSE
Airbus Helicopters introduced a protective measure through the ALERT SERVICE BULLETIN
No. EC225-05A046, which consisted of installing a PTFE skived film between the frame and the seal of
jettisonable windows, in order to reduce the level of effort required for jettisoning.
New investigations carried out on VIP cabin windows equipped with PTFE skived film have revealed that the
thickness of these windows creates greater jettisoning forces than with standard jettisonable windows
equipped with PTFE skived film.
In order to reduce these forces to acceptable levels, Airbus Helicopters has developed an improvement
which consists of removing the PTFE skived film and installing silicone window seals instead of the
polychloroprene seals currently installed on VIP cabin windows.
For helicopters whose S/N is listed on Page 1, this ALERT SERVICE BULLETIN supersedes the instructions
given in ALERT SERVICE BULLETIN No. EC225-05A046.
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory for helicopters
whose Serial Number is listed on page 1.
Revision 0 2018-02-08  Page 2/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN consists of:
- Removing, if installed, the PTFE skived film between the VIP cabin window frame and
seal.
- Replacing the seals of the VIP cabin windows with silicone seals.
g
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
The work on the helicopter is to be performed by the operator.
Helicopters/installed equipment or parts:
For helicopters which do not operate over water:
Comply with paragraph 3. within 250 flying hours following receipt
of this ALERT SERVICE BULLETIN, issued at the date indicated at the bottom of the page.
For helicopters which operate over water:
Comply with paragraph 3. within 110 flying hours following receipt
of this ALERT SERVICE BULLETIN, issued at the date indicated at the bottom of the page.
Non-installed equipment or parts:
Comply with paragraph 3 of this ALERT SERVICE BULLETIN before installing on the helicopter.
Revision 0 2018-02-08  Page 3/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
1.F. APPROVAL
Approval of modifications:
The information or instructions relate to modification 332P087140.00, which was approved on
January 25, 2018 by EASA for civil versions helicopters subject to an Airworthiness Certificate.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on
February 05, 2018 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on
February 05, 2018 under the prerogatives of the recognition of design capability FRA21J-002-DGA for
French Government helicopters.
1.G. MANPOWER
For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following
personnel qualifications:
Qualification: - 1 Airframe Technician to remove the PTFE skived film,
- 2 Airframe Technicians to remove/install the windows.
The time for the operations is given for information purposes, for a standard configuration.
Time for the operations: - approximately 1 hour per window for 2 Airframe Technicians.
Estimated helicopter downtime: approximately 9 days to remove/install the coverings.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
Revision 0 2018-02-08  Page 4/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
1.K. REFERENCES
The documents required for compliance with this ALERT SERVICE BULLETIN are as follows:
Standard Practices Manual:
- MTC: 20.02.05.404: Joining by bolts and nuts.
- MTC: 20.04.01.102: Use of cleaning products on individual parts and on aircraft - Cleaning of parts.
- MTC: 20.04.01.402: Cleaning of removed individual parts with liquid solvents - Cleaning of parts.
- MTC: 20.05.01.212: Implementation of Sealing compound PR 1829 B2 - General sealing procedures.
- MTC: 20.07.03.406: Instructions applicable when working on an aircraft electrical circuit and power
generating systems.
- MTC: 20.07.03.408: Appearance checks on an aircraft after an inspection or repair.
Aircraft Maintenance Manual (MMA):
- MMA: 56-20-00-051: Removal - Installation - Cabin windows.
- MMA: 56-20-00-212: Check the clearance between the seal of the jettisonable window and the cabin lining.
1.L. OTHER AFFECTED PUBLICATIONS
The modification will be integrated in:
- The illustrated Parts Catalog (IPC),
- The Aircraft Maintenance Manual (MMA)
The IPC and MMA documentation will be updated as part of a future revision.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
The PRE MOD seals and the POST MOD seals are not interchangeable.
The PRE MOD seal keys and the POST MOD seal keys are not interchangeable.
Mixability:
The PRE MOD seals and the POST MOD seals are not mixable.
The PRE MOD seal keys and the POST MOD seal keys are not mixable.
Revision 0 2018-02-08  Page 5/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
2. EQUIPMENT OR PARTS INFORMATION
2.A. HARDWARE: PRICE - AVAILABILITY - PROCUREMENT
For any information concerning price of modification kits and/or components, contact the Airbus Helicopters
Network Sales and Customer Relations Department.
Delivery times will be communicated on operator's request by the Sales and Customer Relations
Department.
Order the required quantities from the Sales and Customer Relations Department of the Airbus Helicopters
Network:
Airbus Helicopters
Etablissement de Marignane
Direction des Ventes et Relation Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
For any information, contact the Sales and Customer Relations Department.
Revision 0 2018-02-08  Page 6/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT
Kit to be ordered for one helicopter:
New P/N  Former
Designation  Qty  Item
P/N  →  Instruction
85D seal VIP  332P08-7140-0071
window kit
85D silicone  151601505M
1  1
window seal  (704A39-8210-66)
85D silicone  151601506N
2  2
window seal key  (704A39-8210-67)
Key extraction tape  6  332A23-0520-04  3
extraction tape  Simple key  4  332A23-0520-06  4
Window extraction  6  332A23-0520-07  5
Flat washers  6  23111AG04OLE  6
Self-locking nut  6  ASN52320BH040N  7
Consumables to be ordered separately:
Refer to the Work Cards and Tasks specified in this ALERT SERVICE BULLETIN and the list below:
Designation  Qty  Consumable P/N  CM  Item
Cleaning agent
(Gasoline G)
N8955004956  CM 232  8
Or  AR
Petrol ether  AR  Off the shelf  8
Sealing compound  AR  PR1829B2  CM 6232  9
Adhesive fabric tape  AR  3M 22888  10
Adhesive tape  AR  DHS171-143.21  CM 6229  11
Abrasive paper, 80-grit  AR  Off the shelf  12
The consumables can be ordered separately from KLX AEROSPACE SOLUTIONS company.
Website:  https://www.klxaerospace.com/klxaero/
Telephone:  +1.305.925.2600
AOG:  +1.305.471.8888
Revision 0 2018-02-08  Page 7/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
Special tools:
Designation  Qty  Tool P/N or equivalent  Item
Tool kit  KA6420
Spatula, rounded end  770150225 (commercial P/N)  ZZ
Tube cutter  Off the shelf (Virax 215032)
Insertion tool  Off the shelf (LT 415)  XX
Spatula, curved  1479N/S5 ("Beta" supplier P/N)  ww
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2018-02-08  Page 8/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Read and comply with the instructions concerning assembly by bolts and nuts as per Work Card
20.02.05.404 (MTC).
- Read and comply with the use of cleaning products for individual parts and aircraft as per Work Card
20.04.01.102 (MTC).
3.B. WORK STEPS
NOTE 1
The installation of new seals (1) and seal keys (2) must be
done dry.
Compliance with the work steps is described in a video which is accessible by following the link below:
http://dai.ly/k3DklgBuVI85wlpfkm2
3.B.1. Preliminary steps
- Disconnect all electrical power supplies as per Work Card 20.07.03.406 (MTC).
- Install the access equipment.
- Remove all coverings to gain access to the different work areas.
- Mark the location of the interior key extraction tapes (o) and (p) before removing them (Figure 2).
- Remove the VIP cabin windows (g) Figure 1, as per MMA Task 56-20-00-051.
- Button the press studs (3a) and (4a) (not shown in the Figure) on the new exterior key extraction tapes (3)
and (4) on the press studs (v) and (q) (not shown in the Figure) as per Figure 2, Sections H-H, I-l and F-F:
• Ensure that there is no difficulty in attaching and detaching each of the press studs (3a) and (4a) (not
shown in the Figure).
• Maintain the pairing of the external key extraction tapes (3) and (4) with windows (g) for the remainder of
the procedure.
• If there is a difficulty, contact Airbus Helicopters.
- As per Figure 2 Section H-H and F-F:
• Remove the nuts (r), the washers (t), the screws (u), the window extraction tapes (w) and the press
studs (v).
• Discard the washers (t), all the old window and key external extraction tapes (w) and the nuts (r).
• Set aside the press studs (v) and the screws (u).
3.B.2. Removal of the PTFE skived film
- If installed:
• Remove the PTFE skived film (s) from the window frames, using a spatula (zz).
. Scrap the PTFE skived film (s).
- Clean the window frame using the cleaning agent (8) as per 20.04.01.402 (MTC).
Revision 0 2018-02-08  Page 9/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
3.B.3. Installation of the new window seals (Figures 1 and 2)
- Cut window seals (1) to length using the seals (a), (b), (c), (d) and (e) previously removed as patterns, with
an excess length of 100 mm (3.94 in.), using tube cutter (yy).
- Clean window seals (1) using cleaning agent (8) and a lint-free cloth as per Work Cards 20.04.01.102 and
20.04.01.402 (MTC).
- Check the integrity of window seals (1).
- Install window seals (1) on the structure and comply with the following installation direction:
. The two moulded ribs (1f) of the window seals (1) must be located outside the helicopter, closest to the
fuselage structure.
. Start the installation of seals (1) at joint "F" located on the same side of the window as the interior key
• Secure seals (1) against the structure using adhesive tape (10) during the installation phase.
- Trim off the excess length of window seals (1) using tube cutter (yy):
. Cut to an excess length of 5 to 8 mm (.197 to .315 in.) before completing seal installation.
NOTE 2
in the absence or any excess length, window seals (1) may
retract and create a gap at joint "F"
- Trim the adhesive tape (10) using spatula (ww) without damaging window seals (1), in order to free the
groove, necessary to install the windows.
3.B.4. Installation of VIP windows
- Install the window extraction tape (5) with the press stud (v), flat washer (6), screw (u) and nut (7).
- Tighten nut (7) to standard torque.
- Before installing the windows, position window extraction tape (5) correctly between windows (g) and
window seals (1).
• 10
- Position windows (g) in the groove of window seals (1) as follows:
1/ Position one of the bottom corners of the window in the seal.
2/ Rotate the window to position the bottom edge of the window in the seal.
3/ Install the remaining part of the window frame using spatula (zz).
. If necessary, use jerking motions to facilitate installation of the window in the seal.
. During installation, ease the seal over the window using the spatula.
4/ Slide window (g) upwards within seal (1), in order to center it correctly.
Revision 0 2018-02-08  Page 10/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
NOTE 3
The window  position  centers within seal (1) during
installation of seal keys (2).
010
- Make sure that windows (g) are correctly installed in window seals (1).
- Remove adhesive tape (10) and discard.
- Discard seals (a), (b), (c), (d) and (e).
3.B.5. Installation of seal keys
- Cut interior/exterior seal keys (2) to the same length as seal keys 0), (k), (1), (m) and (n) previously
removed, allowing excess length of 100 mm (3.94 in.), using tube cutter (yy).
- Clean seal keys (2) using cleaning agent (8) and a lint-free cloth as per Work Cards 20.04.01.102 and
20.04.01.402 (MTC).
- Check the integrity of seal keys (2).
- Install the interior extraction tapes (o) and (p) on the interior seal keys (2).
- Install the exterior extraction tapes (3) and (4) on the exterior seal keys (2).
- Install seal keys (2) on window seals (1) using insertion tool (xx) and spatula (zz).
Revision 0 2018-02-08  Page 11/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
• Start the installation at joint "E" or "F" Figure 1 in accordance with the instructions given in Notes 4, 5
and 6 below:
NOTE 4
The joint of interior seal keys (2) must be located opposite
interior extraction tapes (o) and (p).
NOTE 5
The joint of exterior seal keys (2) must be located opposite
exterior extraction tapes (3) and (4).
NOTE 6
The interior extraction tapes (o) and (p) are located at the
same bottom corner of the window as the exterior extraction
tapes (3) and (4) or at the opposite bottom corner,
depending on the configuration of the helicopter.
. Trim off the excess length of the seal keys (2) using tube cutter (yy):
- Cut to an excess length of 8 mm (.315 in.) before completing the installation of the seal keys.
NOTET
In the absence of any excess length (2), the seal keys may
retract and create a gap at joint "E".
- Discard the joint keys (), (k), (I), (m) and (n)
3.B.6. Finishing (Figures 1,2 and 3)
- Mask off around the sealing compound application area at joints "E" and/or "F" of seal keys (2) and window
seals (1) using adhesive tape (11) (see Figure 3).
- Clean the outlined sealant application area using a cleaning agent (8) and a lint-free cloth, complying with
MTC CTs 20.04.01.102 and 20.04.01.402
- Sand the outlined sealing compound application area using sandpaper (12).
- Clean, once again, the outlined sealing compound application area using a cleaning agent (8) and a lint-
free cloth, complying with MTC CTs 20.04.01.102 and 20.04.01.402.
- Apply sealing compound (9) as per Work Card 20.05.01.212 (MTC):
• inside joints "E" and/or "F" of seal keys (2).
• inside joints "F"" of window seals (1).
- Apply a bead of sealing compound (9) to cover outside of joints "E" and "F" of seal keys (2) and window
seals (1).
. During application:
- Ensure an overlap of approximately 1 mm (.039 in.) on each side of the key joint onto the window seal,
as indicated in Figure 3.
- For the joint of window seals (1), make sure that the bead of sealing compound overlaps onto the
window and the fuselage as indicated in Figure 3.
Revision 0 2018-02-08  Page 12/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
- As indicated on Figure 3, apply sealing compound (9) at the joints between the interior/exterior tapes and:
The windows (g).
. The window seals (1).
- Remove and discard adhesive tape (11).
- Attach the exterior extraction tapes (3) to the window extraction tapes (5) using the self-gripping tape (5a)
on the window extraction tapes (5) as per Figure 2, Sections H-H and F-F.
- Button the press studs (3a) on the exterior extraction tapes (3) on the press stud (v) as per Figure 2,
Section H-H.
- Button the press studs (4a) (not shown in the Figure) on the exterior extraction tapes (4) on the press stud
(q) (not shown in the Figure).
3.B.7. Final steps
- Install all the coverings previously removed.
- Check the clearance between the seals and the cabin lining as per MMA Task 56-20-00-212.
- Perform an appearance check on aircraft after inspection or repair as per Work Card 20.07.03.408 (MTC).
- Connect all electrical power supplies as per Work Card 20.07.03.406 (MTC).
- Remove the access equipment.
3.C. COMPLIANCE CONFIRMATION
Application of the directives in this document:
Record compliance with this ALERT SERVICE BULLETIN, with its revision number, in the helicopter
documents.
Tracking of modifications in the documentation:
Record the embodiment of modification 332P087140.00 in the helicopter documents.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
Not applicable.
Maintenance instructions:
After embodiment of this ALERT SERVICE BULLETIN, refer to the Master Servicing Manual (MSM) in effect
for maintenance intervals.
Revision 0 2018-02-08  Page 13/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2018-02-08  Page 14/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
C  15090
Or  Or
(See Figure 2) |
F (See Figure 2)  y H (See Figure 2)
(See Figure 2) JL
*= (See Figure 2)  ~ G (See Figure 2)
Figure 1
Revision 0 2018-02-08  Page 15/19
This document is a  ailable on the internet: www.airbushelicopters.com/techpub

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2018-02-08  Page 16/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
SECTION  SECTION  SECTION
F-F  G-G  H-H
(See Figure 1)  (See Figure 1)
5a
OUTSIDE  INSIDE
INSIDE
½ or ½  2 or ½  eg
OUTSIDE
5a
a or i  BASINO
SECTION  SECTION
1-1  J-J
(See Figure 1)  (See Figure 1)
INSIDE
INSIDE  OUTSIDE
OUTSIDE
Figure 2
Revision 0 2018-02-08  Page 17/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2018-02-08  Page 18/19
This document is available on the internet: www.airbushelicopters.com/techpub

### Page 19 (OCR)

AIRBUS
HELICOPTERS  ASB No EC225-56C012
> 9
1 mm  1 mm
„039 in  (.039 in.
Figure 3
Revision 0 2018-02-08  Page 19/19
This document is available on the internet: www.airk  oushelicopters.com/techpub

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
