# Eurocopter Service Bulletin EC225-63-032

## Copies (3)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision 2 ("Airbus Helicopters SB 63-032 Rev 2"), 50 pages: PDF https://openairdocs.org/files/sha256/2c/74/2c743745619c433a08a14c2aa2d59f28802c34ba3f51dc0dce2906c4914812bc; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-63-032/file/2c743745619c.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0379, the docket of AD 2021-16-05. Not covered by OpenAirDocs’ CC0 dedication.
- Revision 1 ("Airbus Helicopters SB 63-032 Rev 1"), 36 pages: PDF https://openairdocs.org/files/sha256/9b/da/9bda960f00527d0285c63d8c1d40b33565120e473361182f5a4836f1177e71fc; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-63-032/file/9bda960f0052.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0379, the docket of AD 2021-16-05. Not covered by OpenAirDocs’ CC0 dedication.
- No revision named ("Airbus Helicopters SB 63-032 Rev 0"), 27 pages: PDF https://openairdocs.org/files/sha256/ef/9c/ef9c79010142f893b8886a13603c54feb56ab19af9098ce34252af9033962224; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-63-032/file/ef9c79010142.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0379, the docket of AD 2021-16-05. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Service Bulletin)
- Number: EC225-63-032
- Latest revision known: EC225-63-032, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-63-032

## Text (50 pages)

Revision 2, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0379, the docket of AD 2021-16-05. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 1/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 Civil version(s): LP 
  
 
SERVICE BULLETIN 
 
CORRECTIVE MEASURE  
 
MAIN ROTOR DRIVE - MGB lubrication system 
 
Addition of a magnetic plug between the MGB and the oil cooler 
Corresponds to modifications 0753047, 0753052 and 0753053 
 
 
 
 
 
Revision No. Date of issue 
Revision 0 2017-06-23 
Revision 1 2017-07-25 
Revision 2 2018-11-14 
 
 
Summary: 
 
This Service Bulletin consists in adding a new magnetic plug called FFMP (Full Flow Magnetic Plug) between the 
MGB and the oil cooler and cancels the inspection of the oil filter and the oil cooler. 
 
Reason for last Revision: 
 
The purpose of Revision 2 of this Service Bulletin is to take into account customer remarks, modify symbols on 
Figures, correct tightening torques and improve the installation of the new FFMP magnetic plug (MOD 0753053). 
 
Compliance: 
 
Compliance with this Service Bulletin is conditioned by compliance with ALERT SERVICE BULLETIN No. 05A049. 
For the attention of

### Page 2

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 2/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.  PLANNING INFORMATION 
 
 
1.A.  EFFECTIVITY 
 
1.A.1. Helicopters/installed equipment or parts 
 
EC225 LP version helicopters which do not embody modification 0753053. 
 
1.A.2. Non-installed equipment or parts 
 
Not applicable. 
 
 
1.B.  ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C.  REASON 
 
Revision 0: 
 
Following investigations into the fatal accident of an EC225 LP helicopter, which occurred  
on April 29, 2016 in Norway, Airbus Helicopters introduced monitoring measures through ALERT SERVICE  
BULLETIN No. 05A049. 
 
One of these measures is the inspection of the oil cooler which requires the oil cooler to be drained.  
 
 The purpose of this Service Bulletin is to add a new magnetic plug called FFMP (Full Flow Magnetic Plug) to 
collect particles upstream of the oil cooler.  
 
This modification enables the check of the MGB oil filter and oil cooler to be canceled. It will be available in 
early July 2017 and requires a ground run to be carried out after the check of the magnetic plug. 
 
A new optimized definition of the FFMP, which enables the ground run after the check to be canceled, is 
currently being developed and will be available as of mid-July. 
 
 The new magnetic plug must be inspected in acco rdance with the instructions of ALERT SERVICE 
BULLETIN No. 05A049. 
 
Compliance with this Service Bulletin is conditioned by compliance with ALERT SERVICE  
BULLETIN No. 05A049. 
 
Revision 1: 
 
Revision 1 of this Service Bulletin consisted in introducing a new version of the FFMP (MOD 0753052), 
which enables the ground run after inspection to be canceled, and which can be easily locked by a safety 
pin.   
 
Revision 1 affects compliance with the previous revision. 
 
Revision 2:  
 
The purpose of this Service Bulletin is to take into account customer remarks, modify symbols on Figures, 
correct tightening torques and improve the installation of the new FFMP magnetic plug (MOD 0753053). 
 
The revision does not affect compliance with the previous revision.

### Page 3

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 3/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.D.  DESCRIPTION 
 
This Service Bulletin consists in (MOD 0753053): 
- removing the walkway, if necessary, 
- modifying the walkway to install the FFMP (Full Flow Magnetic Plug) manifold assembly support, 
- replacing the hydraulic hose which connects the MGB to the oil cooler, 
- installing a magnetic plug, 
 
or modifying the installation made during compliance with the previous revisions. 
 
 
1.E.  COMPLIANCE 
 
1.E.1. Compliance at H/C manufacturer level  
 
Comply with the instructions given in paragraph 3. of this Service Bulletin according to the operational and 
contractual constraints. 
 
1.E.2. Compliance in service 
 
The work on the helicopter is to be performed by the operator. 
 
Helicopters/installed equipment or parts: 
 
For helicopters on which Revision 0 of this Service Bulletin was not complied with (PRE  
MOD 0753047): 
Comply with paragraph 3., except for paragraph 3.B.2.d. of this Service Bulletin without exceeding the 
deadline imposed in ALERT SERVICE BULLETIN No. 05A049. 
 
For helicopters on which Revision 0 of this Service Bulletin was complied with 
(POST MOD 0753047 and PRE MOD 0753052): 
Comply with paragraph 3., except for paragraphs 3.B.2.a., 3.B.2.b. and 3.B.2.c. of this Service Bulletin 
without exceeding the deadline imposed in ALERT SERVICE BULLETIN No. 05A049. 
 
For helicopters on which revision 1 of this Service Bulletin was complied with   (POST MOD 0753047 
and 0753052): 
Depending on the customer’s decision on compliance, comply with paragraph 3. except for  
paragraphs 3.B.2.a., 3.B.2.b. and 3.B.2.c. of this Service Bulletin during a future inspection, as per 
operational constraints. 
 
Non-installed equipment or parts: 
 
Not applicable.

### Page 4

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 4/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.F.  APPROVAL 
 
 Approval of modifications: 
 
The information or instructions relate to modification 0753047, which was approved on June 23, 2017 by the 
EASA for civil version helicopters subject to an Airworthiness Certificate. 
 
The information or instructions relate to modification 0753052, which was approved on June 30, 2017 by the 
EASA for civil version helicopters subject to an Airworthiness Certificate. 
 
The information or instructions relate to modification 0753053 approved on January 19, 2018 by the EASA 
for civil version helicopters subject to an Airworthiness Certificate. 
 
Approval of this document: 
 
The technical information contained in this Service Bulletin Revision 0 was approved  
on June 23, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version 
helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in this Service Bulletin Revision 0 was approved  
on June 23, 2017 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French 
Government helicopters. 
 
The technical information contained in this Service Bulletin Revision 1 was approved  
on July 18, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version 
helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in this Service Bulletin Revision 1 was approved  
on July 18, 2017 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French 
Government helicopters. 
 
The technical information contained in this Service Bulletin Revision 2 was approved  
on November 14, 2018 under the authority of EASA Design Organization Approval No. 21J.700 for civil 
version helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in this Service Bulletin Revision 2 was approved  
on November 14, 2018 under the prerogatives of the recognition of design capability FRA21J-002-DGA for 
French Government helicopters.

### Page 5

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 5/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.G.  MANPOWER  
 
For compliance with this Service Bulletin, Airbus Helicopters recommends the following personnel 
qualifications:  
 
For helicopters on which Revision 0 of this Service Bulletin was not complied with: 
Qualification: - 2 Mechanical Technicians, 
 - 1 Pilot. 
 
The time for the operations is given for information purposes, for a standard configuration. 
 
Time for the operations:  - approximately 8 hours for the Mechanical Technician, 
 - approximately 15 minutes for the pilot. 
 
Estimated helicopter downtime:  
 
The estimated helicopter downtime is approximately 1 day. 
 
For helicopters on which Revision 0 of this Service Bulletin was complied with: 
Qualification:  - 1 Mechanical Technician, 
- 1 Pilot. 
 
The time for the operations is given for information purposes, for a standard configuration. 
 
Time for the operations:  - approximately 30 minutes for the Mechanical Technician, 
- approximately 15 minutes for the Pilot. 
 
Estimated helicopter downtime:  
 
The estimated helicopter downtime is approximately half a day. 
 
For helicopters on which Revision 1 of this Service Bulletin was complied with: 
Qualification: - 1 Mechanical Technician, 
- 1 Pilot. 
 
The time for the operations is given for information purposes, for a standard configuration. 
 
Time for the operations:  - approximately 30 minutes for the Mechanical Technician, 
- approximately 15 minutes for the Pilot. 
 
Estimated helicopter downtime:  
 
The estimated helicopter downtime is approximately half a day. 
 
 
1.H.  WEIGHT AND BALANCE 
 
After work completion, record weights and moments in Section 6.2 of the Flight Manual (PMV). 
 
For helicopters on which Revision 0 of this Service Bulletin was not complied with: 
Weight: + 1.37 kg. 
 
Longitudinal moment: + 7.49 m.kg. 
 
For helicopters on which Revision 0 of this Service Bulletin was complied with: 
Weight and moment negligible. 
 
For helicopters on which Revision 1 of this Service Bulletin was complied with: 
Not applicable.

### Page 6

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 6/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.I.  POWER CONSUMPTION 
 
Not applicable. 
 
 
1.J.  SOFTWARE UPGRADES/UPDATES 
 
Not applicable. 
 
 
1.K.  REFERENCES 
 
The documents required for compliance with this Service Bulletin are as follows. 
 
Standard Practices Manual (MTC): 
 
- MTC: 20.01.01.303: Use of protective products - Miscellaneous products used on helicopters 
- MTC: 20.01.01.305: Use of hydraulic fluids - Miscellaneous products used on helicopters 
- MTC: 20.02.01.103: Installation of pipes - General 
- MTC: 20.02.01.418: Protection of electrical wiring during maintenance operations - General 
- MTC: 20.02.05.404: Joining by bolts and nuts - Joining 
- MTC: 20.02.06.101: Safetying assemblies: General - Safetying and locking assemblies 
- MTC: 20.02.06.402: Safetying with lockwire - Safetying and locking assemblies 
- MTC: 20.02.07.101: Electrical bonding: General - Electrical bonding 
- MTC: 20.02.07.401: Bonding procedure - Electrical bonding 
- MTC: 20.02.07.402: Bonding procedure applied on metal structure - Electrical bonding 
- MTC: 20.02.07.403: Use of Vernelec 43022 varnish - Electrical bonding 
- MTC: 20.02.08.410: Installation of seals on mechanical or hydraulic assemblies - Replacement of 
components on structure and mechanical assemblies 
- MTC: 20.04.01.102: Use of cleaning products on individual parts and on aircraft - Cleaning 
- MTC: 20.04.03.409: Method for application of GARDACID P4325 - Corrosion inhibiting and removal 
procedures 
- MTC: 20.07.03.408: Appearance checks on an aircraft after an inspection or repair - Technical instructions 
- MTC: 20.08.01.601: Monitoring of lubricating oil contamination on mechanical assemblies equipped with 
magnetic plugs - Periodical monitoring of lubricating oil checking elements  
- MTC: 20.08.05.103: Monitoring of parts in operation - marking - service life customization - General rules 
applicable to aircraft 
 
Aircraft Maintenance Manual (MMA): 
 
- MMA: 12-00-00, 00: Description - General 
- MMA: 12-10-00, 00: Description - Filling and draining 
- MMA: 24-00-00-611: General Instructions - General 
- MMA: 53-73-00-021: Removal - Sliding cowling 
- MMA: 53-73-00-421: Installation - Sliding cowling 
- MMA: 60-00-00-641: Filling and draining 
- MMA: 63-21-00-065: Removal-Installation of MGB Torquemeter Transmitter - Main reduction gear

### Page 7

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 7/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
1.L.  OTHER AFFECTED PUBLICATIONS 
 
The modification will be integrated into the following manuals: 
 
- Illustrated Parts Catalog (IPC). 
- Aircraft Maintenance Manual (MMA). 
- Master Servicing Manual (MSM). 
 
 The documents affected will be updated as part of a future revision. 
 
The update of the IPC documentation must be ordered by the customer. 
 
 
1.M.  PART INTERCHANGEABILITY OR MIXABILITY 
 
Interchangeability: 
 
PRE MOD and POST MOD parts are not interchangeable. 
 
Mixability: 
 
Not applicable.

### Page 8

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 8/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
2.  EQUIPMENT OR PARTS INFORMATION 
 
 
2.A.  EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT 
 
For helicopters PREMOD 0753047 and PRE MOD 0753052 (not having complied with revision 0) 
The kit and tooling (loft) will be delivered free of charge by the Airbus Helicopters' Program Department. 
 
For helicopters POSTMOD 0753047 and/or 0753052 (having complied with revisions 0 and/or 1) 
The price of the kit will be given on the operator’s request, contact the Airbus Helicopters Sales and 
Customer Relations Department. 
 
Airbus Helicopters  
Etablissement de Marignane 
Direction Ventes et Relations Client  
13725 MARIGNANE CEDEX 
FRANCE 
 
NOTE 1 
 
On the purchase order, please specify the mode of 
transport, the destination and the serial numbers of the 
helicopters to be modified. 
 
 
2.B.  LOGISTIC INFORMATION 
 
For any information concerning the modification kits and/or components or assistance, contact the Sales and 
Customer Relations Department. 
 
 
2.C.  EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT 
 
Kits to be ordered for one helicopter or one assembly: 
 
For helicopters PRE MOD 0753047 and PRE MOD 0753052 (not having complied with revision 0) 
 
Designation Qty New P/N Item     Former      P/N        → Instruction 
      
Magnetic plug 
installation kit, 
including: 
 332A75-3052-0072    
      
FFMP support base (eq) 1 332A39-1065-03 1   
Formed support 2 332A39-1068-21 2   
Screw 2 22126BC050016L 3   
Screw 5 22208BC050018L 4   
Special screw 10 ECS2365TK05S16X 5   
Flexible hose, upstream 
(SENSOR Y) 1 
A25490-01 
(704A34412282) 7 A8225 (704A34412210) Discard 
Flexible h, downstream 
(SENSOR Y) 1 
A25489-01 
(704A34412281) 8   
FFMP body 1 1D9317 (704A34412289) 9

### Page 9

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 9/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
Kits to be ordered for one helicopter or one assembly (continued): 
 
Designation Qty New P/N Item     Former      P/N     → Instruction 
      
Magnetic plug 
installation kit, 
including (continued): 
 332A75-3052-0072    
      
FFMP (magnetic plug) 
manifold 1 1A9339 (704A34412290) 10   
Seal For ref. AS3208-16 10a   
Seal For ref. AS3209-019 10b   
Attachment clamp 12 EN4114S38NH0 11   
Washer 9 23111CA050 13   
Nut 9 ASN52320BH050N 14   
Welded hose support 1 332A39-1063-02 15   
Screw 2 22126BC080036L 16   
Washer 7 23119AG050LE 17   
Safety belt 1 332A39-1066-21 18   
Attachment clamp 1 ASNA0021-21G43 19   
Washer 5 23112AG050LE 21   
Union 33 UNJ-M 1 332A39-1062-20 22   
Union 33 UNJ-M 1 332A39-1062-21 23   
O-ring 2 AS3209-122 24   
Screw 2 22209BC050018L 25   
Attachment clamp 2 EN4114S12NH0 26   
Screw 3 22209BC050014L 27   
Washer 2 332A39-1067-22 28   
Screw 2 22208BC050026L 33   
Attachment clamp 3 EN4114S23WH0 34   
Spacer 2 332A39-1069-21 35   
Screw 2 22208BC050014L 39

### Page 10

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 10/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
Kits to be ordered for one helicopter or one assembly (continued): 
 
For helicopters POSTMOD 0753047 and/or 0753052 (having complied with revisions 0 and/or 1) 
 
Designation Qty New P/N Item     Former      P/N   →  Instruction 
      
Magnetic plug 
installation kit, 
including (continued): 
 332A75-3053-0071    
      
FFMP support base (eq) 1 332A39-1065-03 1 332A39-1065-01 Discard 
Formed support 2 332A39-1068-21 2 332A39-1068-20 Discard 
Screw  2 22126BC050016L 3   
Screw 5 22208BC050018L 4   
Special screw 10 ECS2365TK05S16X 5   
FFMP (magnetic plug) 
manifold 1 1A9339 (704A34412290) 10 1A9312 (704A34412283) Discard 
Seal PM AS3208-16 10a   
Seal PM AS3209-019 10b   
Attachment clamp 2 EN4114S38NH0 11   
Washer 9 23111CA050 13   
Nut 9 ASN52320BH050N 14   
Welded hose support 1 332A39-1063-02 15 332A39-1063-01 Discard 
Screw 2 22126BC080036L 16   
Washer 7 23119AG050LE 17   
Safety belt 1 332A39-1066-21 18 332A39-1066-20 Discard 
Washer 5 23112AG050LE 21   
Screw 2 22209BC050018L 25   
Attachment clamp 1 EN4114S12NH0 26   
Screw 3 22209BC050014L 27   
Washer 2 332A39-1067-22 28 332A39-1067-21 Discard 
Screw 2 22208BC050026L 33   
Spacer 2 332A39-1069-21 35 332A39-1069-20 Discard 
Screw 2 22208BC050014L 39

### Page 11

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 11/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
Equipment or parts to be ordered separately: 
 
Designation Qty New P/N Item    Former     P/N      → Instruction 
      
Lockwire A/R EN3628-0,8 (CM776) 6   
      
Attachment clamp 1 EN4114S38NH0 11  Helicopter with APU installation 
Screw 1 22208BC050020L 12  Helicopter with APU installation 
Washer 1 23111CA050 13  Helicopter with APU installation 
Nut 1 ASN52320BH050N 14  Helicopter with APU installation 
Heat-shrink 
sheath A/R VG95343T05F001M 29   
Elastomer A/R ASNA3917E010 36   
Attachment clamp 1 EN4113S20NH 37  Helicopter with APU installation 
Silicone tape A/R ABS5334A01B (CM6940) 38   
      
 
NOTE 2 
 
Components (11), (12), (13), (14) and (37) must only be 
ordered for helicopters with APU installation. 
 
Consumables to be ordered separately: 
 
Refer to the Work Cards and Tasks specified in this Service Bulletin and the list below: 
 
Designation Qty Consumable P/N CM Item 
     
Adhesive A/R DHS171-141.20 6014 20 
Grease A/R AIR4206B 116 30 
Mineral oil A/R AIR3525 / O-155 123 31 
White spirit (cleaning agent) A/R Whitespiritbidon5L 208 32 
 
The consumables can be ordered separately from company KLX AEROSPACE SOLUTIONS.  
Website: https://www.klxaerospace.com/klxaero/ 
Telephone:  +1.305.925.2600 
AOG:  +1.305.471.8888

### Page 12

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 12/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
Special tools: 
 
Refer to the Work Cards and Tasks specified in this Service Bulletin and the list below: 
 
Designation Qty Tooling P/N or equivalent Item 
 
Loft 1 332A39-1065-TG zz 
 
 
NOTE 3 
 
Loft (zz) must be systematic ally ordered and can only be 
used once on the helicopter. 
 
 
2.D.  EQUIPMENT OR PARTS TO BE RETURNED 
 
Not applicable.

### Page 13

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 13/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
3.  ACCOMPLISHMENT INSTRUCTIONS 
 
 
3.A.  GENERAL 
 
- Read and comply with the general instructions as per MMA Task 12-00-00, 00. 
- Read and comply with the general instructions for filling and draining as per MMA Task 12-10-00, 00. 
- Read and comply with the general instructions as per MMA Task 24-00-00-611. 
- Read and comply with the general instructions for the use of protective products as per MTC Work  
Card 20.01.01.303. 
- Read and comply with the general instructions for the use of hydraulic fluids as per MTC Work  
Card 20.01.01.305. 
- Read and comply with the general instructions for the installation of pipes as per MTC Work  
Card 20.02.01.103. 
- Read and comply with the instructions for the protection of electrical wiring during maintenance operations 
as per MTC Work Card 20.02.01.418. 
- Read and comply with the instructions for joining by bolts and nuts as per MTC Work Card 20.02.05.404. 
- Read and comply with the general instructions for safetying assemblies as per MTC Work  
Card 20.02.06.101. 
- Read and comply with the instructions for safetying with lockwire as per MTC Work Card 20.02.06.402. 
- Read and comply with the general instructions for electrical bonding as per MTC Work Card 20.02.07.101. 
- Read and comply with the instructions concerning the electrical bonding procedure as per MTC Work  
Card 20.02.07.401. 
- Read and comply with the instructions concerning the bonding procedure on metal structure as per MTC 
Work Card 20.02.07.402. 
- Read and comply with the general instructions for the use of VERNELEC 43022 varnish - Electrical 
bonding as per MTC Work Card 20.02.07.403. 
- Read and comply with the general instructions for the installation of seals on mechanical or hydraulic 
assemblies as per MTC Work Card 20.02.08.410. 
- Read and comply with the use of cleaning products on individual parts and on aircraft as per MTC Work 
Card 20.04.01.102. 
- Read and comply with the general instructions concerning the GARDACID P4325 application method as 
per MTC Work Card 20.04.03.409. 
 
 
3.B.  WORK STEPS 
 
3.B.1. Preliminary steps 
 
- Park the helicopter in a maintenance workshop. 
- Install the appropriate access equipment. 
- Disconnect all electrical power supplies. 
- Remove all equipment and furnishings as required to gain access to the different work areas. 
- If necessary, remove the sliding cowling as per Sub-task 53-73-00-021-001 of MMA Task 53-73-00-021. 
- Drain the oil from the MGB and the cooler as per Sub-task 60-00-00-641-001 of MMA Task 60-00-00-641. 
(Only for helicopters on which Revisions 0 and 1 of this Service Bulletin was not complied with).

### Page 14

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 14/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
3.B.2. Procedure 
 
 
 
BE CAREFUL TO PROTECT THE WORK AREAS, 
BLANK THE OPENINGS OF REMOVED 
COMPONENTS AND PLUG DISCONNECTED 
ELECTRICAL CONNECTORS IN ORDER TO 
PREVENT FOD INGRESS IN THE SYSTEM. 
 
3.B.2.a. Walkway modification and angle bracket installation (helicopters on which Revision 0 was not 
complied with) 
 
As per Figures 1 and 3 
- If necessary, remove walkway (a) to facilitate access as per Sub-task 63-26-00-032-001 of MMA  
Task 63-26-00-062. 
- Remove and discard hardware (b) from Glycol reservoir (h) (Figure 1 - Detail A). 
 
NOTE 1 
 
The removal of hardware (b) (Figure 1) and the installation 
of screws (3) (Figure 3) must be carried out one after the 
other. 
 
- Perform electrical bonding of supports (2). 
- Attach Glycol reservoir (h) to walkway (a) using screws (3) and supports (2) (Figure 3 - Detail A and 
CROSS-SECTION B-B). 
- Tighten to standard torque. 
- Safety screws (3). 
- Remove and discard hardware (c) from the fan drive support (not shown) (Figure 1 - Detail A). 
- Retain the fan drive support. 
 
As per Figure 2 - Details A and B 
- Position and center loft (zz) to match existing holes (A) and (G) on walkway (a). 
- Temporarily attach FFMP support base (1) and fan drive support (k) to walkway (a) to match existing 
holes (A) and (G) and loft (zz). 
- Mark and trace hole (A) on FFMP support base (1) to match loft (zz). 
- Mark and trace hole (C) on walkway (a) to match loft (zz). 
- Remove FFMP support base (1) and fan drive support (k). 
- Drill holes (A) and (C) into FFMP support base (1) and walkway (a) to diameter 5.5 mm ±0.1. 
- Deburr. 
- Temporarily attach FFMP support base (1) to match holes (A), (C) and (G) on walkway (a). 
- Mark and trace holes (B) on FFMP support base (1) to match walkway (a). 
- Back-drill holes (B) to diameter 5.5 mm ± 0.1. 
- Deburr. 
- Remove the anti-slip coating around holes (C) in walkway (a) over a diameter of 15 mm ±0.5. 
- If necessary, remove the anti-slip coating from existing holes (A) and (B) and (G) over a diameter of  
15 mm ±0.5. 
- Deburr and protect. 
- Cover the marking of area (H) as per MTC Work Card 20.08.05.103. 
- Re-identify walkway (a) as per paragraph 3.C. 
- Clean the work area. 
CAUTION

### Page 15

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 15/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
As per Figure 3 
- Position fan drive support (k) and FFMP support base (1) on walkway (a) (Detail A and  
CROSS-SECTION C-C). 
- Attach fan drive support (k) and FFMP support base (1) to walkway (a) using screws (5)  
(CROSS-SECTION C-C and Detail D). 
- Torque tighten as indicated. 
- Attach FFMP support base (1) to walkway (a) using screws (5) (CROSS-SECTION C-C and Detail E). 
- Tighten to the indicated torque value. 
- Clean the work area. 
 
3.B.2.b. Modification of the hose and its routing (helicopters on which Revision 0 was not complied with) 
 
As per Figure 4 
- Remove and retain the torquemeter (not shown) as per Sub-task 63-21-00-035-001 of MMA  
Task 63-21-00-065. 
- Remove existing hose (f) attached with clamps (d) and hardware (e) and (g) (Details A - PRE MOD, B 
and C). 
- Re-install hardware (e) in the same location. 
- Torque tighten as indicated. 
- Discard hose (f), clamps (d) and hardware (g). 
- Remove and discard the 2 screws (m) from fan unit (p) (Detail A). 
 
As per Figure 5 
- Position upstream flexible hose (7) on walkway (a) as per Details A POST MOD, B and C. 
- Attach one end of upstream flexible hose (7) on the MGB outlet side using mineral oil (31).  
- Bring into contact and tighten by 1/6 of a turn. 
- Safety using lockwire (6). 
- Re-install the torquemeter (not shown) as per Sub-task 63-21-00-435-001 of MMA Task 63-21-00-065. 
- Route upstream flexible hose (7) between existing hose (n) and walkway (a) using clamps (11) and (34), 
screws (4), washers (13) and (17), nuts (14) and a piece of tape (38) (Details A POST MOD, B and D). 
For helicopters with APU installation: 
- Attach upstream flexible hose (7) to existing hose (y) using clamps (11) and (37), one screw (12), one 
washer (13) and one nut (14) (Details A POST MOD, B, D and D1). 
- Install upstream flexible hose (7) on supports (2) of walkway (a) using clamps (11), screws (39),  
washers (13) and nuts (14) (Details A POST MOD, B and C). 
- Do not yet tighten nuts (14). 
- Route upstream flexible hose (7) on hoses (r) and (t) using clamps (11) and (34), screws (33),  
spacers (35), washers (13) and nuts (14) (Details B, D, E and F). 
- Do not yet tighten nuts (14). 
 
As per Figure 6 
- Install welded hose support (15) on fan unit (p) using screws (16), washers (28) and grease (30)  
(Details A POST MOD and B). 
- Torque tighten as indicated. 
- Safety screws (16) to each other using lockwire (6). 
- Route downstream flexible hose (8) along walkway (a) and welded hose support (15) (Detail A POST 
MOD and C). 
- Attach one end of downstream flexible hose (8) on the cooler side using mineral oil (31) (Detail A - POST 
MOD).  
- Bring into contact and tighten by 1/6 of a turn. 
- Safety using lockwire (6).

### Page 16

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 16/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
- Install downstream flexible hose (8) on welded hose support (15) using clamps (11) and (26),  
screws (4), washers (13) and (17), nuts (14) and silicone tape (38) (Details A - POST MOD, C). 
- Do not yet tighten nuts (14). 
- Install downstream flexible hose (8) on existing hose (u) using clamps (11), one screw (4), washers (13) 
and (17) and one nut (14) (Detail A POST MOD and E). 
- Do not yet tighten nut (14). 
 
3.B.2.c. Magnetic plug (FFMP) and manifold installation (helicopters on which Revision 0 was not complied 
with) 
 
 
 
IN ORDER NOT TO LOSE ANY PARTICLES, BE 
CAREFUL NOT TO BRING THE REMOVABLE PART 
OF THE FFMP INTO CONTACT WITH THE 
WALKWAY OR ANY OTHER METAL OBJECT. 
 
3.B.2.c.1. Manifold installation 
 
As per Figure 7 
- Install unions (22) and (23) on FFMP body (9) using seals (24) and oil (31) (Details A, B and C and 
CROSS-SECTION D-D). 
 
NOTE 2 
 
During the assembly of unions (22) and (23), make sure that 
the "ISO M" marking faces the hose side. 
 
- Torque tighten as indicated and as per Work Card 20.02.05.404 (MTC). 
- Install upstream flexible hose (7) on union (22) using mineral oil (31). 
- Bring into contact and tighten by 1/6 of a turn. 
- Install downstream flexible hose (8) on union (23) using mineral oil (31). 
- Bring into contact and tighten by 1/6 of a turn. 
- Attach FFMP body (9) to FFMP support base (1) to match the 2 existing holes (E) using 
clamps (11) and (19), screws (25) and washers (17) and (21) (Detail C and CROSS-SECTIONS D-D and 
E-E). 
- Do not yet tighten screws (25). 
- Install safety belt (18) on FFMP support base (1) to match the 3 existing holes (F) using screws (27) and 
washers (21) (Detail C and CROSS-SECTIONS D-D and F-F). 
- If necessary, adjust the position of FFMP body (9) to ensure a 1 mm clearance. 
- Tighten all screws (25) and (27) to standard torque. 
- Safety FFMP manifold (10), all screws (25) and (27) and unions (22) and (23) using lockwire (6) and  
heat-shrink sheath (29) as per Details A and B. 
 
NOTE 3 
 
Shrinking heat-shrink sheath (29) to ensure a protection 
against friction between lockwire (6) and clamps (11) or (19) 
is not mandatory. 
CAUTION

### Page 17

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 17/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
As per Figures 5 and 6 
- Torque tighten all nuts (14) and attachment clamps (11), (25), (26) and (34) to the standard torque. 
 
NOTE 4 
 
It is necessary to ensure that there is no interference 
between: 
- flexible hoses (7) and (8) and the sliding cowling, 
- flexible hoses (7) and (8) and the existing hoses, 
- flexible hoses (7) and (8) and the existing electrical 
harnesses, 
- flexible hose (7) and the MGB attachment bar. 
 
3.B.2.c.2. Magnetic plug installation 
 
As per Figure 7 
- Install the fixed part of FFMP (magnetic plug) manifold (10) equipped with its seal (10a) on FFMP  
body (9) using mineral oil (31) (Details A, B and C and CROSS-SECTION D-D). 
 
NOTE 5 
 
All seals must be lubricated with mineral oil (31) before 
installation. 
 
- Tighten to the indicated torque and as per Work Card 20.02.05.404 (MTC). 
- Install the removable part of FFMP (magnetic plug) manifold (10) and both seals (10b) on the fixed part 
of FFMP (magnetic plug) manifold (10) using mineral oil (31). 
- Tighten to contact.  
 
 
 
 
MAKE SURE THAT THE AREA PAINTED IN RED ON 
THE FIXED PART OF FFMP MANIFOLD (10) IS NO 
LONGER VISIBLE. 
 
- Attach the removable part of FFMP (magnetic plug) manifold (10) to the fixed part of FFMP manifold (10) 
using a safety pin. 
- Clean all the work areas.  
 
3.B.2.d. Improvement of the installation of the FFMP manifold (Helicopter having complied with  
Revision 0 and/or Revision 1) 
  
3.B.2.d.1. Replacement of the angle bracket 
 
As per Figure 9 
- Remove the safety belt (da) and the clamps (fa) and (ha) from the FFMP support base (ra) secured 
with the hardware (ea) (Details A and C). 
- Retain the clamps (fa) and (ha). 
- Discard the safety belt (da) and the hardware (ea). 
- Remove and discard the hardware (c) from the fan drive support (k) and from the FFMP support  
base (ra) (Detail A POST MOD). 
CAUTION

### Page 18

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 18/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
- Retain the fan drive support (k). 
- Discard the FFMP support base (ra) and the hardware (c). 
- Place the fan drive support (k) and the FFMP support base (1) on the walkway (a)  
(Detail A and SECTION B-B). 
- Attach the fan drive support (k) and the FFMP support base (1) on the walkway (a) using the screws (5) 
(SECTION B-B and Details D and E). 
- Tighten to the specified torque. 
- Clean the work area. 
 
3.B.2.d.2. Improvement of the hose attachment system 
 
As per Figure 10 
- Remove and retain the attachment clamps (ba) of the hoses (aa) attached with the hardware (x)  
(Details A, B and C). 
- Discard the hardware (x). 
- Remove and discard the 2 formed supports (y) attached with the hardware (z). 
- Perform the electrical bonding of the formed supports (2). 
- Install the 2 formed supports (2) in their place using the screws (3). 
- Tighten to the standard torque. 
- Safety the screws (3). 
- Attach the hose (aa) on the 2 formed supports (2) using the attachment clamps (ba) (previously 
retained), the screws (39), the washers (13) and the nuts (14). 
- Tighten to the standard torque. 
- Remove and discard the hardware (ma) of the clamps (sa) the hoses (aa) and (n) and from the 
walkway (a) (Details A, B and D). 
- Attach the clamps (sa) using a screw (4), washers (17) and (13), a nut (14) and some silicone tape 
(38). 
- Tighten to the standard torque. 
- Remove and discard the hardware (ta) of the clamps (ka) the hoses (aa) and (r) (Details A, B and E). 
- Attach the clamps (ka) of the hoses (aa) and (r), using a screw (33), a spacer (35), a washer (13) and a 
nut (14). 
- Tighten to the standard torque. 
- Remove and discard the hardware (ta) of the clamps (ia) the hoses (aa) and (t) (Details A, B, D and E). 
- Attach the clamps (ka) the hoses (aa) and (t) using a screw (33), a spacer (35), a washer (13) and a 
nut (14). 
- Tighten to the standard torque. 
 
As per Figure 11 
- Remove and discard the support (va) and its hardware (ua) (Details A and B). 
- Install the welded support (15) in its place, attached with the screws (16) and the washers (28). 
- Tighten to the specified torque. 
- Safety the screws (16) collectively using lock wire (6). 
- Remove the large clamps (na) and the small clamps (pa) and (ya) of the hoses (ca) attached with the 
hardware (qa) (Details A, B and C). 
- Retain the large clamps (na) and the small clamp (ya). 
- Discard the small clamp (pa) and all the hardware (qa). 
- Reinstall in their place the large clamps (na), the small clamp (ya) and the clamp (26) on the hose (ca) 
and the welded support (15) using the screws (4), the washers (17) and (13) and the  
nuts (14). 
- Tighten to the standard torque. 
- Remove the clamps (wa) of the hoses (ca) and (u), secured with the hardware (xa)  
(Details A and D). 
- Discard the clamps (wa) and the hardware (xa). 
- Install the clamps (11) in their place on the hoses (ca) and (u) using a screw (4), washers (17) and (13) 
and a nut (14).

### Page 19

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 19/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
As per Figure 12 
- Attach the FFMP body (w) on the FFMP support base (1) to match the 2 holes (E) using the clamps 
(fa) and (ha) (retained previously), the screws (25) and the washers (21) and (17) (Details A  
and C and SECTIONS D-D and E-E). 
- Do not yet tighten the screws (25)  
- Bond a piece of elastomer (36) on the safety belt (18) (except on the bearing surfaces) using the 
adhesive (20) (Details A and B). 
- Install the safety belt (18) on the FFMP support base (1) to match the 3 holes (F), using the screws   
(27) and the washers (21) (Detail C, SECTIONS D-D and F-F). 
- If necessary, adjust the positioning of the FFMP body (w), making sure that there is 1 mm play. 
- Tighten all the screws (25) and (27) to the standard torque value. 
- Lock the FFMP body (w), all the screws (25) and (27) using lockwire (6) and heat-shrink sheath (29) as 
per Details A and B. 
   
NOTE 6 
 
It is not imperative to shrink the heat-shrink sheath (29) to 
protect against friction between the lockwire (6) and the 
clamps (fa) or (ha). 
 
3.B.2.d.3. FFMP manifold installation 
 
 As per Figure 8 
- Unsafety FFMP manifold (v) from FFMP body (w). 
 - Remove and discard FFMP manifold (v). 
 - Install the fixed part of FFMP (magnetic plug) mani fold (10) equipped with its seal (10a) on FFMP  
body (w) using mineral oil (31) (Detail B POST MOD 0753052). 
 
 NOTE 7 
 
All seals must be lubricated with mineral oil (31) before 
installation. 
 
- Tighten to the indicated torque and as per Work Card 20.02.05.404 (MTC). 
- Install the removable part of FFMP (magnetic plug) manifold (10) and both seals (10b) on the fixed part of 
FFMP (magnetic plug) manifold (10) using mineral oil (31). 
- Tighten to contact. 
 
  
  
 
MAKE SURE THAT THE AREA PAINTED IN RED ON 
THE FIXED PART OF FFMP MANIFOLD (10) IS NO 
LONGER VISIBLE. 
  
- Attach the removable part of FFMP (magnetic plug) manifold (10) to the fixed part of FFMP manifold (10) 
using a safety pin. 
- Clean all the work areas. 
 
CAUTION

### Page 20

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 20/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
3.B.3. Tests 
 
- Establish the helicopter in the test configuration. 
- Top up the MGB oil level as per Sub-task 60-00-00-641-004 of MMA Task 60-00-00-641. 
- Make sure that there are no leaks in static condition. 
 
3.B.4. Final steps 
 
- De-energize the helicopter electrical power systems. 
- Clean and recondition the work areas and the helicopter as per MTC Work Card 20.07.03.408. 
- If necessary, install the sliding cowling as per Sub-task 53-73-00-421-001 of MMA Task 53-73-00-421. 
- Install equipment and furnishings removed during preliminary steps (paragraph 3.B.1.). 
- Remove the access equipment. 
- Return the helicopter to flight configuration. 
 
3.B.5. Ground-run/flight test 
 
- Perform a ground-run. 
- Make sure that there are no leaks. 
 
3.B.6. Work steps for non-installed equipment or parts 
 
It is the operator's responsibility to replace and build up new stocks. 
 
 
3.C.  COMPLIANCE CONFIRMATION 
 
Compliance with this document: 
 
Record full compliance with this document, with the revision number, in the helicopter documents. 
 
Tracking of modifications in the documentation: 
 
For helicopters on which Revision 0 of this Service Bulletin was not complied with: 
Record the embodiment of modifications 0753047 and 0753053 in the helicopter documents. 
 
For helicopters on which Revision 0 of this Service Bulletin was complied with: 
Record the embodiment of modification 0753053 in the helicopter documents. 
 
For helicopters on which Revision 1 of this Service Bulletin was complied with: 
Invalidate the embodiment of modification 0753052 and record the embodiment of modification 0753053 in 
the helicopter documents. 
 
Identification of modifications on equipment or parts: 
 
 Identify the parts / assemblies in accordance with th e table below and/or MTC Work Card 20.08.05.103.  
 
Designation Former P/N New P/N MOD Type of marking
     
Walkway 332A22-3298-05 332A08-8969-04 0753047 Ink

### Page 21

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 21/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
3.D.  OPERATING AND MAINTENANCE INSTRUCTIONS 
 
Operating instructions: 
 
Not applicable. 
 
Maintenance instructions: 
 
Refer to the instructions of ALERT SERVICE BULLETIN No. 05A049 to inspect the new magnetic plug. 
 
Refer to the maintenance operations listed in Appendix 4.A. and to the Tasks in Appendix 4.B. 
 
NOTE 8 
 
The tasks provided in Appendix 4.A. must be used for 
maintenance pending their integration in the helicopter 
documentation. 
 
The Aircraft Maintenance Manual (MMA) and the Master Servicing Manual (MSM) will incorporate these 
instructions as part of a future revision. Once these instructions have been integrated in the Aircraft 
Maintenance Manual (MMA) and the Master Servicing Manual (MSM), refer to these manuals. 
 
 
 
 
BEFORE HANDLING THE FFMP, MAKE SURE THE FFMP 
HAS COOLED SUFFICIENTLY SINCE ENGINE 
SHUTDOWN TO PREVENT ANY RISK OF BURNS.  
IF NECESSARY, WEAR PROTECTIVE GLOVES TO 
REMOVE THE FFMP. 
 
 
WARNING

### Page 22

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 22/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Figure 1 
a 
b 
c
PRE MOD
h

### Page 23

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 23/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2 
a 
B 
H 
C
a 
G 
zz
k 1 
A 
B
A

### Page 24

SB No. EC225-63-032 
Revision 0    2017-06-23   Page 24/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 25

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 25/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 3 
POST MOD 
a 
1 
CROSS-SECTION 
B-B 
h
2 
3
a 
h 
5 1 
a 
k 
5 1
k 
a 
0.21 - 0.23 daNm
18.28 - 20.35 Ibf.in
0.21 - 0.23 daNm
18.28 - 20.35 Ibf.in
CROSS-SECTION 
C-C

### Page 26

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 26/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 27

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 27/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
X5460 
X5877.6 
X6390 
X6815 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4 
PRE MOD 
m
d f d 
g 
d
e
p
d 
e 
AIR4206 
0,22 - 0,27 daNm 
19.47 - 23.89 Ibf.in
AIR4206 
0,22 - 0,27 daNm 
19.47 - 23.89 Ibf.in

### Page 28

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 28/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 29

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 29/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 5 
POST MOD
7 
31 
a 
E
F 
35 
11 
7 
33 
13 
14 
34 
t
7
4 
11
17 
13 
14 
n 
4 
11 
13 
14 
17 
34 
a
F
E 
7 
11 
34 
35 
33 
13 
14 
r 
D1
D1
WITH APU
7 
11
37
12
13
14
2 
7 1139
13
14
y
38

### Page 30

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 30/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 31

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 31/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 6 
8 
31 
p 
16
28
15 
a
0.8 - 1.2 daNm 
70.8 - 106.2 Ibf.in 
AIR 4206
8 
E 
POST MOD
4
11
17
13
14
26
38
8 
4 
11 
13 
14 
17 
26 
38 
E 
11 4
11
13
14
17
u

### Page 32

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 32/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 33

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 33/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 7 
18
36
CROSS-SECTION
D-D 1 10 
10a 
10b 
31 
23
31
24F 9 24 
22 
31 
E 
F 
 1 
19 1118 
F
F
1
2929 
E
E
E 
7
31
8 
31 
10
27 
21 
18 
1 
11 OR 19 
CROSS-SECTION 
F-F 
17 1 
CROSS-SECTION 
E-E 
21 
25 
F
F
  AIR 3525 
  AIR 3525 
   AIR 3525 
DHS171-141.20
4.2 - 5 daNm
0.84 - 1.26 daNm
4.2 - 5 daNm
74.35 - 111 lbf.in

### Page 34

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 34/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 35

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 35/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 8 
0.84 - 1.26 daNm 
10 
10a 
10b 
31
v 
POST MOD 0753047 / POST MOD 0753052 
POST MOD 0753053
w 
w 
  AIR 3525  
74.35 - 111 Ibf.in

### Page 36

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 36/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 37

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 37/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 9
POST MOD
a
1 
ra
CROSS-SECTION 
B-B 
k 
5 1
k 
a 
0,21 - 0,23 daNm
18.28 - 20.35 Ibf.in
0,21 - 0,23 daNm
18.28 - 20.35 Ibf.in
5 1 
a 
E 
da
ea
ea
ha
ea 
ea
fa
ra
1
E 
c 
0.21 - 0.23 daNm
0.21 - 0.23 daNm

### Page 38

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 38/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 39

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 39/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 10 
POST MOD
aa 
 
a 
E
t
aa
sa 
ma 
4 
17 
13 
14 
n 
sa 
ma
4 
13 
14 
17 
a
F
E 
aa
ka 
ka 
ta 
35 
33 
13 
14 
r 
z 
y 
2 
aa xba
39
13
14
38
3 
F 
35 
ia 
aa 
ta 
33 
13 
14 
ia

### Page 40

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 40/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 41

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 41/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 11
D 
p 
ua
16
28
va 
15 
a
0,8 - 1,2 daNm 
70.8 - 106.2 Ibf.in 
AIR 4206
ca 
POST MOD
qa 
4 
17 
13 
14 
ca 
na 
qa
ya 
4 
17 
13 
14 
11 
wa 
xa 
4
11
13
14
17
wa
xa
u
ca 
D 
na 
pa 
26
0.8 - 1.2 daNm

### Page 42

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 42/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 43

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 43/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 12 
18
36
CROSS-SECTION
D-D 1 10 
10a 
10b 
31 
F w 
E 
F 
 1 
ha fa18 
F
F
1
29 
E
E
E 
ca 
10
27 
21 
18 
1 
fa 
ha 
CROSS-SECTION 
F-F 
17 1 
CROSS-SECTION 
E-E 
21 
25 
F
F
  AIR 3525 
DHS171-141.20
0.84 - 1.26 daNm

### Page 44

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 44/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PAGE LEFT BLANK INTENTIONALLY

### Page 45

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 45/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/ 
 
4.  APPENDIX 
 
 
4.A.  MASTER SERVICING MANUAL (MSM) 
 
Task Number 
Description/Remarks 
Documentation Interval Margin 
63/24/03/000/100/0XX                                                                                                                               MG 04 
Oil cooling system with by-pass valve 
 
                                                   MMA    63.24.03.211                              600 FH   // 4Y                         60 FH 
                                                               63.24.03.211.002 
 
 
POST MOD 0753053 
Check of FFMP installation. 
GVI 
63/24/03/000/100/0XX                                                                                                                               MG 04 
Oil cooling system 
 
                                                   MMA    63.24.03.211                              600 FH // 4Y                          60 FH 
                                                               63.24.03.211.002 
 
 
POST MOD 0753053 
Check of FFMP installation. 
GVI 
 
 
NOTE 
 
The checking procedure has remained identical for 
helicopters with or without by-pass valve.

### Page 46 (OCR)

AIRBUS
HELICOPTERS  SB No. EC225-63-032
4.B. CHECK OF THE OIL COOLING SYSTEM (COOLING UNIT)
1 REQUIRED EQUIPMENT
1.1  Special Tools
access ladder  Aircraft tool kit
1.2  Materials
None
1.3 Replacement Parts
None
1.4 Applicable Documents
Aircraft Maintenance Manual (AMM):
Task 60-00-00-641
Task 63-24-03-064
Filling and Draining
Removal-Installation of the FFMP (Full Flow
Magnetic Plug) particle collector
1.5  General Information
- Standard Practices Manual (MTC):
MTC 20-02-05-404  Assembly by screws and nuts
MTC 20-02-06-402  Safetying with lockwire
2 PRELIMINARY STEPS
Install the access equipment.
- Open the sliding cowling.
3 PROCEDURE
Sub-task 63-24-03-211-001
(Figure 1) (Figure 2)
3.1  Check
- (Figure 1)
- Check for oil leakage, especially at:
Revision 0 2017-06-23  Page 46/50
Revision 2 2018-11-14  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 47 (OCR)

AIRBUS
HELICOPTERS  SB No. EC225-63-032
the nuts of pipes (5), (8) on cooler (3),
the nuts of MGB pipes (2) and filter (1),
• the cells and welds of cooler (3) from inside the rear duct (4).
Check the condition of:
• attachments: tightened, safetied, no loose rivets, no corrosion, no distortion, no cracks,
NOTE:
If the safetying is damaged (lockwire) and/or the
screws and/or nuts are loose: check the torque
and safety.
front and rear ducts (16) and (4),
• cooler (3) supports (9) and fan (14) supports (10),
angle brackets (7), LH and RH struts (6),
supports (11) for pipes (5) and (8),
fan (14) air intake screen (13),
front duct - fan coupling clamp (15),
fan (14) drive shaft (12).
Make sure that there is no interference between the pipes and fixed parts.
Check blades and fan assembly for foreign bodies.
Check MGB oil level as per task 60-00-00-641 sub-task 60-00-00-641-004.
Sub-task 63-24-03-211-002
3.2  Check the Full Flow Magnetic Plug (FFMP) installation
- (Figure 2)
- Check the condition of:
the pipes (1) and (15) (no cuts, distortion or interference),
couplings (6), (7) and (10), (11) (distortion, no corrosion, no leaks, safetying),
of FFMP (8) (no corrosion, no leaks, safetying),
FFMP support (12):
no cracks or corrosion,
condition of clamp attachments and safetying,
no loose rivets
.. by touch, check the attachment bolts for support (12) under the walkway, for FFMP (8) on
support (12) and for the safety belt (9) foolproof device have not become loose.
support (13) for pipe (1) (at the fan):
no cracks or corrosion,
.. by touch, check the attachment bolts (14) have not become loose.
clamps for pipes (1) and (15),
(POST MOD 0753053) for the foam between the safety belt (9) and the FFMP,
shrinkable sheath for the safetying of all FFMP elements.
Remove the particle collector (4) as per sub-task 63-24-03-034-001 of task 63-24-03-064.
Check the magnetization of the particle collector (4) using a ferromagnetic element placed on
the magnetic element.
Revision 0 2017-06-23  Page 47/50
Revision 2 2018-11-14  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 48

SB No. EC225-63-032 
Revision 0    2017-06-23 Page 48/50 
Revision 2    2018-11-14 This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 49 (OCR)

AIRBUS
HELICOPTERS  SB No. EC225-63-032
9
- 10
POST MOD 0726335
Figure 1
Revision 0 2017-06-23  Page 49/50
Revision 2 2018-11-14  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 50 (OCR)

AIRBUS
HELICOPTERS  SB No. EC225-63-032
FWD
PRE MOD 0753052
POST MOD 0753052
PRE MOD 0753053
PRE MOD 0753053
POST MOD 0753053
POST MOD 0753053
￾14
Figure 2
Revision 0 2017-06-23  Page 50/50
Revision 2 2018-11-14  This document is available on the internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
