# Airbus Helicopters Alert Service Bulletin EC225-64A011

Copy: No revision named ("Airbus Helicopters ASB No. EC225-64A011 Rev 0"), 16 pages: PDF https://openairdocs.org/files/sha256/78/74/787475adadf9c4a005ac67225abfcc1cb9cb553396f43fe7cfd9e776fe3afdec; text https://openairdocs.org/service-documents/airbus-helicopters/ec225-64a011/file/787475adadf9.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1018, the docket of AD 2022-03-17. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: EC225-64A011
- Page: https://openairdocs.org/service-documents/airbus-helicopters/ec225-64a011

## Text (16 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1018, the docket of AD 2022-03-17. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
Civil version(s): LP
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
TAIL ROTOR - TAIL ROTOR ASSEMBLY
Check of the angular clearances of the Tail Gear Box (TGB)
For the attention of
Revision No.  Date of issue
Revision 0  2021-06-30
Summary:
The objective of this ALERT SERVICE BULLETIN is to do a check of the angular clearances of the Tail Gear Box
(TGB).
Compliance:
It is mandatory to comply with this ALERT SERVICE BULLETIN.
Revision 0 2021-06-30  Page 1/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Tail Gear Boxes (TGB) installed on EC225 helicopter version LP, Part Number (P/N) 332A36.5001.01.
1.A.2. Non-installed equipment or parts
Tail Gear Boxes (TGB) Part Number (P/N) 332A36.5001.01.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
During an inspection on an EC225 helicopter version LP, a check of the TGB chip detector was done, which
showed coloration of the oil.
A borescope inspection was subsequently done and also showed internal coloration of the TGB.
Then, an oil analysis was done, which showed an increased iron rate.
The TGB was removed and sent to be examined.
After disassembly, a loss of the tightening torque of the nut that attaches the TGB bevel wheel was found.
Consequently, with this ALERT SERVICE BULLETIN, Airbus Helicopters makes it mandatory to do a check
of the TGB angular clearances.
1.D. DESCRIPTION
This ALERT SERVICE BULLETIN makes you do a check of the TGB angular clearances with a new method
of measurement.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
Revision 0 2021-06-30  Page 2/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
1.E.2. Compliance in service
It is the operator who does the work on the helicopter.
Helicopters/installed equipment or parts:
Comply with paragraph 3. of this ALERT SERVICE BULLETIN not more than 110 flight hours after you
received this ALERT SERVICE BULLETIN (refer to the issue date on the page footer) and thereafter at
intervals not more than 1320 flight hours.
Non-installed equipment or parts:
Comply with paragraph 3. of this ALERT SERVICE BULLETIN after the installation of a TGB with a TSN or
TSO of more than O flight hours and thereafter at intervals not more than 1320 flight hours.
1.F. APPROVAL
Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on June 28, 2021 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on June 28, 2021 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French
Government helicopters.
1.G. MANPOWER
Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this
qualification:
Qualification: 2 Mechanical Technicians.
The man-hours are an estimate given for information only and for a standard helicopter configuration.
Estimated Man-hours: 1 hour for 2 Mechanical Technicians.
The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.
The estimate of the helicopter downtime is 1 hour to do the check of the TGB angular clearances.
1 H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
Revision 0 2021-06-30  Page 3/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
These documents are necessary to comply with this ALERT SERVICE BULLETIN.
Aircraft Maintenance Manual (MMA):
MMA: 64-20-00-021: Removal - TAIL ROTOR DRIVE ASSEMBLY
MMA: 64-20-00-421: Installation - TAIL ROTOR DRIVE ASSEMBLY
MMA: 65-11-00-063: Removal / Installation of a drive line component and a flexible coupling - DRIVE SHAFT
Standard Practice Manual (MTC):
MTC: 20-02-05-404: Assembly by screws and nuts - Joining
MTC: 20-07-02-201: Helicopter parked in a repair shop - Safety instructions
MTC: 20-07-03-408: Appearance checks on an aircraft after inspection or repair - Technical instructions
Information Notice (IN):
IN 3481-1-00: The Marketplace: an AirbusWorld Ordering service
IN 3643-1-00: Introduction of the digital Service Bulletin reporting service R-TEX
1.L. OTHER AFFECTED PUBLICATIONS
Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Interchangeability:
No effect on Interchangeability.
Mixability:
No effect on mixability.
Revision 0 2021-06-30  Page 4/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For information about the price of the modification kits and/or components, or for aid, contact the Airbus
Helicopters Network Sales and Customer Relations Department.
Availability
Contact the Sales and Customer Relations Department to know the delivery lead times.
Procurement
Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations
Department:
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
In the purchase order, write the information that follows:
- The mode of transport
- The destination
- The serial numbers of the helicopters to change.
NOTE 2
Send your order for ALERT SERVICE BULLETINS to:
- Telex: HELICOP 410 969F
- Fax: +33 (0)4.42.85.99.96
2.B. LOGISTIC INFORMATION
Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Consumables to be ordered separately:
Refer to the Tasks identified in this ALERT SERVICE BULLETIN.
You can order the consumables from the AirbusWorld Marketplace through e-ordering (IN 3481-1-00).
If you cannot get access to e-ordering, please contact your Logistic Focal Point.
Revision 0 2021-06-30  Page 5/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
Special tools:
Key Word  Qty  Tool P/N or equivalent  Item
Upper angle  1  332A94-3371-27  ZZ
LORIS 500  1  703A94-0000-24
Comparator MECACEL  1  703A94-0000-21
Nut diameter 8mm  2  Commercial  ww
Washer  2  Commercial
2.D. EQUIPMENT OR PARTS TO BE RETURNED
Not applicable.
Revision 0 2021-06-30  Page 6/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
Comply with the general instructions on assembly by screws and nuts Refer to Work Card 20-02-05-404
(MTC).
3.B. WORK STEPS
3.B.1. Preliminary steps
- Park the helicopter in a hangar. Refer to Work Card 20-07-02-201 (MTC).
- Install a maintenance platform.
- Remove and/or open all applicable cowlings, panels, doors and other items of equipment to get access to
the different work areas.
3.B.2. Check of the angular clearances of the Tail Gear Box (TGB)
3.B.2.a. Installation of the measurement tools (Figures 1 to 5)
- On the TGB side, disconnect the inclined drive shaft (a) (Figure 1). Refer to Sub-task 65-11-00-033-001 of
Task 65-11-00-063 (MMA).
- Make sure that the TGB input flange (b) and the inclined drive shaft (a) are not connected.
- Align the red blade of the tail rotor along the vertical plane, with the blade tip toward the ground (Figure 5).
- a
Figure 1
Revision 0 2021-06-30  Page 7/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
- Disconnect two points of the electrical harness (Figure 2).
Points of electrical harness
Figure 2
NOTE 1
If the electrical harness is not installed in this configuration,
the TGB screws can be used as an alternative solution to
attach the upper angle (zz).
- Attach the upper angle (zz) (Figure 3) to the TGB housing with:
• Two 8 mm nuts (ww) (not shown)
. The applicable washers (vv) (not shown).
- Make sure that the upper angle (zz) is correctly attached.
- Attach the LORIS 500 support (yy) below the upper angle (zz) (Figure 3).
- Install the MECACEL comparator (xx) on the LORIS 500 support (Vy).
- Install the probe of the MECACEL comparator (xx) on the TGB input flange, on the flat surface (Figure 4).
- Make sure that the probe of the MECACEL comparator (xx) is at a 10-mm (.393 in.) distance from the
border of the TGB input flange (Figure 4).
- Make sure that the probe of the MECACEL comparator (xx) is perpendicular to the TGB input flange
(Figure 4).
ZZ
Figure 3
Revision 0 2021-06-30  Page 8/16
This document is available on the Internet: www.ai  ishelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
6°0.
10 mm (.393 in.)
Figure 4
- Lock the red blade vertically, as near as possible to the blade tip, to prevent its movement (Figure 5).
NOTE 2
The use of a platform makes it easier to vertically lock the
red blade with the foot and by hand to prevent its movement
(Figure 5).
- Make sure that the vertical blade cannot move.
Figure 5
Revision 0 2021-06-30  Page 9/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
3.B.2.b. Clockwise measurements of the angular clearances of the Tail Gear Box (TGB) (Figures 6 and 7)
CAUTION
MAKE SURE THAT THE VERTICAL BLADE DOES
NOT MOVE DURING ALL THE STEPS THAT
FOLLOW.
- Turn the TGB input flange slowly and manually clockwise (Figure 6) until the last mechanical stop.
NOTE 3
Only a small angular displacement is necessary.
CAUTION
NOTE 4 BELOW IS APPLICABLE TO ALL OF THE
REMAINING PROCEDURE.
NOTE 4
The first mechanical stop is related to the normal play
between the TGB pinion and the wheel teeth. If there are
some abnormal angular plays in the TGB, one more
mechanical stop can be felt. It is necessary that you are at
the last mechanical stop before you continue the
measurement procedure.
Figure 6
- Set the MECACEL comparator (xx) to "0" (Figure 3).
Revision 0 2021-06-30  Page 10/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
- Turn the TGB input flange slowly and manually counterclockwise (Figure 7) until the last opposite
mechanical stop.
NOTE 5
Only a small angular displacement is necessary.
- Record the value measured on the MECACEL comparator (xx) (Figure 3).
PERIODI
Figure 7
- Apply again a clockwise displacement (Figure 6) until the mechanical stop on the TGB input flange.
- Make sure that the comparator still shows "O.
Interpretation of the results:
. If the comparator shows accurately "O", record the measured value.
.. Comply with paragraph 3.B.2.b. a second time.
. If the comparator shows "0" with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Add 0.02 mm (.000079 in) to the measured value.
.. Comply with paragraph 3.B.2.b. a second time.
. If the comparator value does not show "0" with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Do not record the measured value.
.. Comply with paragraph 3.B.2.b. again.
- Record the values of each of the 2 clockwise measures.
Revision 0 2021-06-30  Page 11/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
3.B.2.c. Counterclockwise measurements of the angular clearances of the Tail Gear Box (TGB)
(Figures 3, 8 and 9)
CAUTION
MAKE SURE THAT THE VERTICAL BLADE DOES
NOT MOVE DURING ALL THE STEPS THAT
FOLLOW.
- Turn the TGB input flange slowly and manually counterclockwise (Figure 8) until the last mechanical stop.
NOTE 6
Only a small angular displacement is necessary.
CAUTION
NOTE 7 BELOW IS APPLICABLE TO ALL OF THE
REMAINING PROCEDURE.
NOTE 7
The first mechanical stop is related to the normal play
between the TGB pinion and the wheel teeth. If there are
some abnormal angular plays in the TGB, one more
mechanical stop can be felt. It is necessary that you are at
the  last mechanical stop before you continue the
measurement procedure.
Figure 8
- Set the MECACEL comparator (xx) to "0" (Figure 3).
Revision 0 2021-06-30  Page 12/16
This document is available on the Internet: www.airb  ushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
- Turn the TGB input flange slowly and manually clockwise (Figure 9) until the last opposite mechanical
stop.
NOTE 8
Only a small angular displacement is necessary.
- Record the value measured on the MECACEL comparator (xx) (Figure 3).
PERIOD
Figure 9
- Apply again a counterclockwise displacement (Figure 8) until the mechanical stop on the TGB input
flange.
- Make sure that the comparator still shows "O.
Interpretation of the results
• If the comparator shows accurately "O", record the measured value.
.. Comply with paragraph 3.B.2.c. a second time.
• If the comparator shows "0 with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Add 0.02 mm (.000079 in) to the measured value.
.. Comply with paragraph 3.B.2.c. a second time.
If the comparator value does not show "0" with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Do not record the measured value.
.. Comply with paragraph 3.B.2.c. again.
- Record the value of each of the 2 counterclockwise measures.
3.B.2.d. Registration of the measured values
- On the TGB log card, write the mean value of the 4 recorded measures (the 2 clockwise measures of
paragraph 3.B.2.b. and the 2 counterclockwise measures of paragraph 3.B.2.c.).
- Do a check of the clearance values recorded and refer to Table No. 1 below for more instructions.
Revision 0 2021-06-30  Page 13/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
Table No. 1
Checks  Touch-ups  Discard
- If the value of the measured clearance is less than or equal to
0.34 mm (.013 in), keep as is and set the helicopter back to  None  None
flight configuration.
- If the value of the measured clearance is more than 0.34 mm
(.013 in) and less than 0.69 mm (.027 in):
. Keep as is and set the helicopter to flight configuration, obey
the procedure to do a check of the angular play every
100 flight hours.  None
. Do the check again at each basic inspection (1200 FH) if the
value of the measured clearance does not change after two
checks at near intervals.
- If the value of the measured clearance is more than or equal to
0.69 mm (.027 in):
. Replace the TGB. Refer to Task 64-20-00-021 (MMA).  None
• Install an airworthy TGB. Refer to Task 64-20-00-421 (MMA).
None
Send the removed TGB to Airbus
Helicopters or to an approved repair
station to have it examined.
3.B.2.e. Removal of the measurement tools (Figures 1 to 3)
- Remove the MECACEL comparator (xx) (Figure 3).
- Remove the LORIS 500 support (yy).
- Remove the applicable washers (vv) (not shown) and the two 8-mm diameter nuts (ww) (not shown).
- Remove the upper angle (zz).
- Connect two points of the electrical harness (Figure 2).
- On the TGB side, connect the inclined drive shaft (a) (Figure 1). Refer to Sub-task 65-11-00-433-001 of
Task 65-11-00-063 (MMA).
- At each check of the angular clearance in compliance with this ALERT SERVICE BULLETIN (see
Table No. 1, not applicable to the basic inspection every 1200 FH), fill the response form in paragraph 4
(APPENDIX) and send it to Airbus Helicopters at the address specified in the response form.
3.B.3. Final steps
- Install or close all cowlings, panels, doors and items of equipment that you removed and/or opened during
the preliminary steps (paragraph 3.B.1. of this ALERT SERVICE BULLETIN).
- Do appearance checks on the helicopter after inspection or repair. Refer to Work Card 20-07-03-408
(MTC).
- Remove the maintenance platform.
- Set the helicopter back to flight condition.
Revision 0 2021-06-30  Page 14/16
This document is available on the Internet: www. airb  ushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record the full compliance with this ALERT SERVICE BULLETIN, with the revision number, in
the TGB Log Card (FM).
- Please confirm compliance with this ALERT SERVICE BULLETIN (see IN 3643-1-00 for instructions):
QR code or hypertext link
NOTE 9
The recording of  compliance with ALERT SERVICE
BULLETINS in the R-Tex tool does not replace the recording
in the helicopter documents.
ASB EC225-64A011
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2021-06-30  Page 15/16
This document is available on the Internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS  HELICOPTERS
No. EC225-64A011
4. APPENDIX
Response Form of ALERT SERVICE BULLETIN EC225-64A011
"Check of the angular clearances of the Tail Gear Box (TGB)"
Complete this response form and send it, with the value of the TGB angular clearance, by e-mail to
Airbus Helicopters at the address that follows:
- Keycopter: Technical Request Management: TechnicalSupport.Helicopters@airbus.com
- E-mail: support.technical-dyncomp.ah@airbus.com
- Fax: + 33(0) 442.85.99.66
Operator Name and Address:
Helicopter Type and Version:
Helicopter Serial Number (S/N):
Helicopter Flight Hours:
S/N of the Tail Gear Box (TGB):
TGB Flight Hours: TSN:  TSO:
Recorded TGB angular clearance:
Date:  Signature:
Please make a copy of this page. The original form must stay in the ALERT SERVICE BULLETIN.
Revision 0 2021-06-30  Page 16/16
This document is available on the Internet: www.air  ushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
