# Airbus Helicopters Alert Service Bulletin MBB-BK117

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- No revision named ("Airbus Helicopters ASB MBB-BK117  2 67A 030 Rev 0"), 29 pages: PDF https://openairdocs.org/files/sha256/eb/39/eb39659a3f3972368890ad2d58d2511de53168d2efc98b6915f60bf63ff6da8e; text https://openairdocs.org/service-documents/airbus-helicopters/mbb-bk117/file/eb39659a3f39.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1007, the docket of AD 2022-02-20. Not covered by OpenAirDocs’ CC0 dedication.
- No revision named ("Airbus Helicopters ASB MBB-BK117 D 2 67A 019 Rev 0"), 24 pages: PDF https://openairdocs.org/files/sha256/c6/d2/c6d2b839ac4b9773e9a080390a9b4af363edf24d9004eb98d7af4b89d325a0a5; text https://openairdocs.org/service-documents/airbus-helicopters/mbb-bk117/file/c6d2b839ac4b.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1007, the docket of AD 2022-02-20. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: MBB-BK117
- Page: https://openairdocs.org/service-documents/airbus-helicopters/mbb-bk117

## ADs that cite it (3) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2009-11-01](https://openairdocs.org/ad/2009-11-01.md), effective Jun 12, 2009: No revision named
- [AD 98-24-13](https://openairdocs.org/ad/98-24-13.md), effective Dec 4, 1998: No revision named
- [AD 97-20-16](https://openairdocs.org/ad/97-20-16.md), effective Oct 24, 1997: No revision named

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/airbus-helicopters/mbb-bk117/proposed.md).

## Text (29 pages)

No revision named, the newest copy. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1007, the docket of AD 2022-02-20. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
Valid for Version(s): C-2, C-2e.
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
ROTOR FLIGHT CONTROL - Upper controls
Inspection for correct installation of the collective
bellcrank
For the attention of
Revision No.  Date of issue
Revision O  2021-03-15
Summary:
With this Alert Service Bulletin (ASB), Airbus Helicopters introduces a one-time inspection for
correct installation of the collective bellcrank.
Compliance:
It is mandatory to comply with this ASB.
Revision 0, 2021-03-15  PAGE 1 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
1  PLANNING INFORMATION
1.A EFFECTIVITY
1.A.1 Helicopters/installed equipment and parts
a) MBB-BK117 C-2, C-2e, all S/N up to 9869 inclusive*.
* The S/N 9870 and on are delivered after the release of this ASB and the collective bellcrank-K
has not been replaced in service on these S/Ns.
b) Bellcrank-K  P/N B670M7021101
P/N B670M7021102
1.A.2 Non-installed equipment and parts
Not applicable.
1.B  ASSOCIATED REQUIREMENTS
None.
1.C  REASON
A collective bellcrank-K was replaced in service and incorrectly installed (rotated by
180°). This collective bellcrank-K was operated on a helicopter and was found during
an inspection. Consequently, with this ASB the installation of the collective
bellcrank-K must be inspected and if necessary corrected. In addition, the AMM tasks
AMM 67-10-00, 5-3, AMM 67-13-00, 4-3 and AMM 67-13-00, 4-4 were changed to
ensure correct installation of the collective bellcrank-K and to ensure free movement
after its installation.
1.D  DESCRIPTION
Examine the documents of the collective bellcrank-K. If necessary, inspect the
collective bellcrank-K for correct installation, inspect the affected areas and replace
the affected components.
1.E  COMPLIANCE
1.E.1 Compliance at H/C manufacturer level
Helicopters/installed equipment and parts:
Not affected.
Non-installed equipment and parts:
Not affected.
PAGE 2 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
1.E.2 Compliance in service
Helicopters/installed equipment and parts:
Part I: Examination of the documents of the collective bellcrank-K
Examine the documents of the collective bellcrank-K in accordance with Section
3.B. 1 within the next 100 Fh or before the 30 September, 2021 whichever occurs
first after receipt of this ASB.
Part II: Inspection of the collective bellcrank-K
If necessary based on the results of Part I of this ASB, inspect the collective
bellcrank-K in accordance with Section 3.B.2 within the next 100 Fh or before the
30 September, 2021 whichever occurs first after receipt of this ASB.
Part III: Correction of the installation of the collective bellcrank-K
If necessary based on the results of Part Il of this ASB, correct the installation of the
collective bellcrank-K in accordance with Section 3.B.3 before the next flight.
Part IV: Correction of the position marking of the collective bellcrank-K (already
installed in the correct position)
Latest during the next disassembly of the bellcrank assembly correct the position
marking of the collective bellcrank-K in accordance with Section 3.B.4.
Revision 0, 2021-03-15  PAGE 3 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
Part I)
The
collective
bel crank-K
has been installed in
accordance with  No
AMM 67-13-00, 4-4?
End of
Part I
y Yes/unknown
Part II)
The
distance Z
is < 69 mm as shown  No
in Figure 1?
Part III
Correct the installation of the
Yes  collective bellcrank-K.
The  End of
position  Part II!
marking
of the collective  No
bellcrank-K is applied
as shown in  Forecast the compliance time of
Figure 1?  Part IV and schedule the
accomplishment accordingly.
Yes
End of
End of
Part II
Part I|
(Part IV
Correct the position marking of
the collective bellcrank-K.
End of
Part IV
PAGE 4 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
Non-installed equipment and parts:
Not affected.
1.F  APPROVAL
Approval of this document:
The technical content of this document is approved under the authority of
DOA No. EASA.21J.700.
1.G  MANPOWER
Qualification  Mechanic  Electrician  Pilot  Others*
approx. 0.5 h  approx. 0.5 h
(inspection)  (inspection)
Estimated  approx. 8 h
Man-hours  (removal and
installation, if
necessary)
* CAMO (or equivalent)
1.H  WEIGHT AND BALANCE
No effect on weight and balance.
1.I  POWER CONSUMPTION
Not affected.
SOFTWARE UPGRADES/UPDATES
Not changed.
1.K  REFERENCES
AMM MBB-BK117 C-2.
1.L  OTHER AFFECTED PUBLICATIONS
Publications already updated:
The changes to AMM MBB-BK117 C-2 which were necessary as a result of this ASB
are already incorporated.
Publications to be updated:
Not affected.
1.M  INTERCHANGEABILITY OR MIXABILITY OF PARTS
Interchangeability:
Not affected.
Mixability:
Not affected.
Revision 0, 2021-03-15  PAGE 5 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 6 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
2  MATERIAL INFORMATION
2.A  MATERIAL: PRICE - AVAILABILITY - PROCUREMENT
None.
2.B  LOGISTIC INFORMATION
None.
2.C  MATERIAL REQUIRED PER HELICOPTER/COMPONENT
None.
2.D  MATERIAL TO BE RETURNED
None.
PAGE 6 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
ACCOMPLISHMENT INSTRUCTIONS
З.А  GENERAL
Obey the "General Recommendations for Working at Helicopters"
(AMM 00-20-02, 2-1).
З.В  WORK STEPS
Part I: Examination of the documents of the collective bellcrank-K
З.В.1  Examination of the documents of the collective bellcrank-K
1. Examine the helicopter documents to determine if the collective bellcrank-K
(4, Fig. 1) has been installed in accordance with AMM 67-13-00, 4-4:
a. If the collective bellcrank-K (4, Fig. 1) has been installed in accordance with
AMM 67-13-00, 4-4, proceed with Section 3.B.2.
b. If the collective bellcrank-K (4, Fig. 1) has never been removed since build of
the helicopter, it is not necessary to accomplish Part II, Part III and Part IV of
this ASB. Proceed with Section 3.C to confirm accomplishment of Part I.
c. If it cannot be determined if the collective bellcrank-K (4, Fig. 1) has been
installed in accordance with AMM 67-13-00, 4-4, proceed with Section 3.B.2.
Part II: Inspection of the collective bellcrank-K
3.В.2  Inspection of the collective bel crank-K
1. Remove the transmission cowlings (AMM 71-11-00, 4-3).
2. Measure the distance Z, between the front edge of the bearing block (7, Fig. 1)
and the front edge of the collective bellcrank-K (4), as shown in Figure 1 to
determine if the installation is correct:
a. If the distance Z is less than 69 mm, the installation of the collective
bellcrank-K (4, Fig. 1) can be determined as correct. Proceed in accordance
with Section 3.B.2.3.
b. If the distance Z is more than or equal to 69 mm, the installation of the
collective bellcrank-K (4, Fig. 1) cannot be determined as correct. Proceed in
accordance with Section 3.B.3.
3. Make sure that the position marking (5, Fig. 1) is applied as shown in Figure 1:
a. If the position marking (5, Fig. 1) is applied as shown in Figure 1, proceed with
Section 3.B.2.4.
b. If the position marking (5, Fig. 1) is not applied as shown in Figure 1:
- Forecast the compliance time of Part IV and schedule the accomplishment
accordingly
- Install the transmission cowlings (AMM 71-11-00, 4-3)
- Proceed with Section 3.C to confirm accomplishment of Part I and Part II.
4. Install the transmission cowlings (AMM 71-11-00, 4-3).
5. It is not necessary to accomplish Part III and Part IV of this ASB. Proceed with
Section 3.C to confirm accomplishment of Part I and Part II.
Revision 0, 2021-03-15  PAGE 7 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 8 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
View A
Detail C
View D
× 1
68 mm  View B
>
FW D
Bolt
2  Bolt
З  Bellcrank-Q  < 69 mm
4  Bel crank-K  6  N
5  Position marking
6  Bel crank-L
Bearing block
For information only
Inspection of the collective bellcrank-K
Figure 1
PAGE 8 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 9 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
Part III: Correction of the installation of the collective bellcrank-K
З.В.З  Correction of the installation of the collective bel crank-K
1. Remove the bellcrank-K (4, Fig. 1) (AMM 67-13-00, 4-4).
2. Discard the bellcrank-K (4, Fig. 1) and the bolts (1, 2).
3. Inspect the bearing block (1, Fig. 2), in the affected area, for signs of chafing:
a. If the bearing block (1, Fig. 2) has signs of chafing, replace the bearing block
(1) (AMM 67-13-00, 4-4). Proceed with Section 3.B.3.4.
b. If the bearing block (1, Fig. 2) has no signs of chafing, proceed with Section
З.В.3.4.
4. Inspect the control lever (2, Fig. 2), in the affected area, for signs of chafing:
a. If the control lever (2, Fig. 2) has signs of chafing, replace the control lever (2)
(AMM 67-13-00, 4-5). Proceed with Section 3.B.3.5.
b. If the control lever (2, Fig. 2) has no signs of chafing, proceed with Section
З.В.З.5.
5. Inspect the forked lever (3, Fig. 2), in the affected area, for signs of chafing:
a. If the forked lever (3, Fig. 2) has signs of chafing, replace the forked lever (3)
(AMM 67-13-00, 4-6). Proceed with Section 3.B.3.6.
b. If the forked lever (3, Fig. 2) has no signs of chafing, proceed with Section
З.В.3.6.
6. Inspect the sliding sleeve (4, Fig. 2), in the affected area, for signs of chafing:
a. If the sliding sleeve (4, Fig. 2) has signs of chafing, replace the sliding sleeve
(4) (AMM 62-31-00, 4-3). Proceed with Section 3.B.3.7.
b. If the sliding sleeve (4, Fig. 2) has no signs of chafing, proceed with Section
З.В.3.7.
7. Inspect the bearing ring (5, Fig. 2), in the affected area, for signs of chafing:
a. If the bearing ring (5, Fig. 2) has signs of chafing, replace the bearing ring (5)
(AMM 62-31-00, 4-3). Proceed with Section 3.B.3.8.
b. If the bearing ring (5, Fig. 2) has no signs of chafing, proceed with Section
3.В.3.8.
Revision 0, 2021-03-15  PAGE 9 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
8. Create a Technical Event (TE) on WebTEK. Airbus Helicopters will analyze the
data. Depending on the results, additional limitations are necessary for the
affected components:
a. With WebTEK access:
- Create a TE on WebTEK: https://airbusworld.helicopters.airbus.com
- Select the TE business domain: "SB/ASB Feedback"
- Select the request type: "MBB-BK117 C-2-67A-030"
- Insert the data as shown on the reply form sheet on page 15 and 16.
- Send the TE.
b. Without WebTEK access:
- Copy, fill out and send back the reply form sheet on page 15 and 16.
9. Continue as detailed in the support feedback received from Airbus Helicopters.
10. Install a serviceable bellcrank-K (4, Fig. 1) with an applied position marking (5) as
shown in Figure 1 and serviceable bolts (1, 2) (AMM 67-13-00, 4-4).
11. Install the transmission cowlings (AMM 71-11-00, 4-3).
12. It is not necessary to accomplish Part IV of this ASB. Proceed with Section 3.C to
confirm accomplishment of Part I, Part Il and Part III.
Part IV: Correction of the position marking of the collective bellcrank-K (already installed in
the correct position)
З.B.4  Correction of the position marking of the collective bellcrank-K (already installed in
the correct position)
1. Remove the transmission cowlings (AMM 71-11-00, 4-3).
2. Remove the bellcrank-K (4, Fig. 1) (AMM 67-13-00, 4-4).
3. The bel crank-K (4, Fig. 1) can be reworked or replaced:
a. For the rework of the bellcrank-K (4, Fig. 1) contact Airbus Helicopters via
customersupport.helicopters@airbus.com to request rework instructions for
the bellcrank-K (4) and continue as detailed in the support feedback received
from Airbus Helicopters.
b. For the replacement of the bellcrank-K (4, Fig. 1) proceed with Section 3.B.4.4.
4. Discard the bellcrank-K (4, Fig. 1).
5. Install a serviceable bellcrank-K (4, Fig. 1) with an applied position marking (5) as
shown in Figure 1 (AMM 67-13-00, 4-4).
6. Install the transmission cowlings (AMM 71-11-00, 4-3).
7. It is not necessary to accomplish Part IIl of this ASB. Proceed with Section 3.C to
confirm accomplishment of Part IV.
PAGE 10 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
View A
Detail C
View E  Detail D
View B
1 Bearing block
2 Control lever
Forked lever
4 Sliding sleeve
5 Bearing ring
Inspection of the affected areas
Figure 2
Revision 0, 2021-03-15  PAGE 11 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
View A
View B
1 Main rotor actuator MHA-collective
2 Tube horizontal control rod (collective)
3 Rod end assy
4 Rod end assy
5  Bolt (bearing block)
6  Tube vertical control rod (collective)
7 Rod end assy
8  Rod end assy
Additional affected components
Figure 3
PAGE 12 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
З.С  COMPLIANCE CONFIRMATION
Compliance with this document:
Part I: Examination of the documents of the collective bellcrank-K
Please confirm compliance with this ASB (see IN 3643-1-00 for details):
QR-Code or hypertext link
NOTE
The recording of compliance with ASBs in the R-Tex
tool does not replace the recording in the helicopter
documents.
ASB MBB-BK117 C-2-67A-030
Confirm accomplishment of Part I of this ASB, with the revision number, by an entry
in the helicopter documents.
Confirm accomplishment of Part I of this ASB, with the revision number, by an entry
in the log card of the equipment (if a log card exists).
Part II: Inspection of the collective bellcrank-K
Confirm accomplishment of Part Il of this ASB, with the revision number, by an entry
in the helicopter documents.
Confirm accomplishment of Part Il of this ASB, with the revision number, by an entry
in the log card of the equipment (if a log card exists).
Part III: Correction of the installation of the collective bellcrank-K
Confirm accomplishment of Part III of this ASB, with the revision number, by an entry
in the helicopter documents.
Confirm accomplishment of Part III of this ASB, with the revision number, by an entry
in the log card of the equipment (if a log card exists).
Part IV: Correction of the position marking of the collective bellcrank-K (already
installed in the correct position)
Confirm accomplishment of Part IV of this ASB, with the revision number, by an
entry in the helicopter documents.
Confirm accomplishment of Part IV of this ASB, with the revision number, by an
entry in the log card of the equipment (if a log card exists).
Revision 0, 2021-03-15  PAGE 13 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
3.D  OPERATING AND MAINTENANCE INSTRUCTIONS
Operating instructions:
None.
Maintenance instructions:
NOTE  The pre-print of the "Removal / Installation - Bellcrank Assembly"
(AMM 67-13-00, 4-3), "Disassembly / Assembly - Bellcrank Assembly"
(AMM 67-13-00, 4-4) and 'Operational Test - Free Movement of the
Main Rotor Controls (AMM 67-10-00, 5-3) is published on ORION.
Until the distribution of the AMM MBB-BK117 C-2 containing the new instructions,
the "Removal / Installation - Bellcrank Assembly" (AMM 67-13-00, 4-3), "Disassembly
/ Assembly - Bellcrank Assembly" (AMM 67-13-00, 4-4) and "Operational Test - Free
Movement of the Main Rotor Controlsi (AMM 67-10-00, 5-3) must be used as shown
in Section 4.
PAGE 14 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
APPENDIX
4.A Reply form sheet
Reply form sheet
for ASB MBB-BK117 C-2-67A-030 Revision O Inspection for correct installation of the
collective bellcrank"
Please completely fill out reply form sheet and send it to the given e-mail.
To
Airbus Helicopters
Customer Support
e-mail: customersupport.helicopters@airbus.com
ASB  Chafing
No.  Keyword  P/N  S/N  Fh
location  Yes  No  • N/A
B671M7002201
Bearing block  (1, Fig. 2)  B671M7002205  Л
B671M3010101
2  Control lever  (2, Fig. 2)  B671M3010102  J
B671M7007201
B671M7007205
Forked lever  (3, Fig. 2)  B671M7018102
105-41961
4  Sliding sleeve  (4, Fig. 2)
117-41932
5  Bearing ring  (5, Fig. 2)
B673M30A1203
Main rotor
(1626A0000-03)
actuator MHA-  (1, Fig. 3)
collective
Tube horizontal  B291M1015201
7  control rod  (2, Fig. 3)  D671M4201202
(collective)
105-45371
Rod end assy
B671M3007110
Ball-end assy  (3, Fig. 3)
Rod end  D671M4701111
M12X1.5R
Revision 0, 2021-03-15  PAGE 15 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
Reply form sheet
for ASB MBB-BK117 C-2-67A-030 Revision O Inspection for correct installation of the
collective bellcrank"
ASB  Chafing
No.  Keyword  P/N  SAN  Fh
location  Yes  No  N/A
105-45372
Rod end assy
J  B671M3007111
9  Ball-end assy  (4, Fig. 3)
Rod end
M12X1.5L
Bolt (bearing  117-44101.10
10  (5, Fig. 3)
block)
Tube vertical
11  control rod  (6, Fig. 3)
(collective)
LEST-SON
Rod end assy
12  Ball-end assy  (7, Fig. 3)
Rod end
M12X1.5R
LEST-SOT
Rod end assy
13  Ball-end assy  (8, Fig. 3)
J
Rod end  D671M4701121
M12X1.5L  J
PAGE 16 of 17  Revision 0, 2021-03-15
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS  HELICOPTERS
ASB MBB-BK117 C-2-67A-030
4.B  Pre-prints
Pre-print of the:
- "Removal / Installation - Bellcrank Assembly" (AMM 67-13-00, 4-3)
- "Disassembly / Assembly - Bellcrank Assembly" (AMM 67-13-00, 4-4)
- "Operational Test - Free Movement of the Main Rotor Controls" (AMM 67-10-00,
5-3).
Revision 0, 2021-03-15  PAGE 17 of 17
This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 18

Aircraft Maintenance Manual (AMM) MBB BK117-C2
Upper Controls - Removal / Installation
EFFECTIVITY ALL
4-3 Removal / Installation - Bellcrank Assembly
A. References:
02-00-00, 2-3 ................................. Scrape rs
63-21-00, 7-1 ................................. Painti ng - Main Transmission
67-00-00, 5-1 ................................. Riggin g - Power-Boosted Section of the Main Rotor
Controls
67-10-00, 4-1 ................................. Remova l / Installation - Control Rods in the Boosted
Section of the Main Rotor Controls
67-10-00, 5-3 ................................. Operat ional Test - Free Movement of the Main Rotor
Controls
67-13-00, 4-1 ................................. Remova l / Installation - Control Rods for Upper Controls
67-13-00, 6-3 ................................. Inspec tion - Bellcrank Assembly
B. Special Tools:
None.
C. Consumable Materials:
CM 202 ......................................... Clean ing Agent
CM 518 ......................................... Anti- Corrosion Agent
CM 2001 ....................................... Cleani ng Agent
CM 6056 ....................................... Sealin g Compound
D. Routine Replacement Parts:
None.
E. Job Set-up:
(1) Remove the control rods of the boosted section of the main rotor controls (67-10-00,
4-1).
(2) Remove the control rods of the upper controls (67-13-00, 4-1).
F. Procedure:
(1) Obey the related Material Safety Data Sheet and local reg ulations when you use
consumable materials.
(2) Remove the bellcrank assembly (3, Figure 401 ) as follows:
(a) Use a scraper (02-00-00, 2-3) and remove the bead seal (5) of sealing compound
from the joint between the main transmission housing and the bellcrank assembly (
3).
(b) Remove the screws (1, 6) and the washers (2) from the bellc rank assembly (3).
Conf. Code: 000 67-13-00, 4-3 Page 401
2021.02.22
PRE PRINT

### Page 19

Aircraft Maintenance Manual (AMM) MBB BK117-C2
CAUTION METAL TOOLS CAN CAUSE DAMAGE TO THE BELLCRANK
ASSEMBLY AND/OR THE MAIN TRANSMISSION HOUSING. DO
NOT USE A SCREW DRIVER OR ANOTHER METAL TOOL TO
REMOVE THE BELLCRANK ASSEMBLY FROM THE BUSHINGS
IN THE MAIN TRANSMISSION HOUSING. USE A WOODEN OR
PLASTIC MALLET TO TAP THE SIDES OF THE BELLCRANK
ASSEMBLY WHILE YOU PULL IT OFF WITH THE OTHER HAND.
(c) Carefully remove the bellcrank assembly (3) from the mai n transmission housing.
(d) Remove the bushings (4) from the bellcrank assembly (3).
(e) Use a lint-free cloth made moist with Cleaning Agent CM 20 2 or Cleaning Agent CM
2001 to remove residual sealing compound from the main trans mission housing and
the bellcrank assembly (3).
(3) Examine the bushings (4) for mechanical damage and/or co rrosion. If there are
mechanical damage and/or corrosion, replace the bushings ( 4).
(4) Examine the interface area of the main transmission hous ing for mechanical damage
and/or corrosion.
(a) If there are mechanical damage and/or corrosion, repair the main transmission
housing (63-21-00, 7-1).
(5) Examine the bellcrank assembly (67-13-00, 6-3).
(6) Install the bellcrank assembly (3, Figure 401 ) as follows:
(a) Apply a thin layer of Anti-Corrosion Agent CM 518 on the bu shings (4).
(b) Put the bushings (4) in its installation position on the m ain transmission housing.
(c) Put the bellcrank assembly (3) in its installation posit ion on the bushings (4).
(d) Install the screws (1,6) and the washers (2) on the bellcr ank assembly (3).
(e) Apply a torque between 13 Nm and 15 Nm (115.1 lbf.in to 132. 7 lbf.in) to the
screws (1, 6).
(f) Apply a bead seal (5) of Sealing Compound CM 6056 around th e interface between
the bellcrank assembly (3) and the main transmission housin g.
G. Close-up:
(1) Install the control rods for the upper controls (67-13-0 0, 4-1).
(2) Install the control rods of the boosted section of the mai n rotor controls (67-10-00, 4-1).
(3) If you replaced any component of the bellcrank assembly, do the rigging procedure for
the main rotor controls (67-00-00, 5-1).
(4) Do the free movement test of the main rotor controls (67-1 0-00, 5-3)
(5) Remove all tools and other materials and clean the work ar ea.
Conf. Code: 000 67-13-00, 4-3 Page 402
2021.02.22
PRE PRINT

### Page 20

Aircraft Maintenance Manual (AMM) MBB BK117-C2
A
BKC26713M100300MU02
B
B
C
C
FWD
(115.1−132.7 lbf.in)
13−15 Nm
(115.1−132.7 lbf.in)
13−15 Nm
(115.1−132.7 lbf.in)
13−15 Nm
(115.1−132.7 lbf.in)
13−15 Nm
A
1
2
3
1
2
4
53
5
6
1
2
2
Removal / Installation - Upper Controls - Bellcrank Assembl y
Figure 401
Conf. Code: 000 67-13-00, 4-3
END OF MODULE
Page 403
2021.02.22
PRE PRINT

### Page 21

Aircraft Maintenance Manual (AMM) MBB BK117-C2
Upper Controls - Removal / Installation
EFFECTIVITY ALL
4-4 Disassembly / Assembly - Bellcrank Assembly
A. References:
67-13-00, 4-3 ................................. Remova l / Installation - Bellcrank Assembly
B. Special Tools:
None.
C. Consumable Materials:
CM 115 ......................................... Greas e
D. Routine Replacement Parts:
AMM
Fig. Item Description Reference
Figure 401 (7) Split pin (P/N LN94-30030)
Figure 401 (8) Nut (P/N MBBN3049-14D)
Table 401 Routine Replacement Parts
E. Job Set-up:
(1) Remove the bellcrank assembly (67-13-00, 4-3).
F. Procedure:
(1) Obey the related Material Safety Data Sheet and local reg ulations when you use
consumable materials.
(2) Disassemble the bellcrank assembly as follows:
(a) Remove and discard the split pin (7).
(b) Remove the nut (8), the washer (9) and the screw (1) from th e bearing block (4).
(c) Remove the tubes (2, 3, 10) the bellcrank Q (11), the bellc rank K (13) and the
bellcrank L (15) from the bearing block (4).
1 Mark the installation position and orientation of the bellc rank Q (11), the
bellcrank K (13) and the bellcrank L (15).
2 Mark the installation position of the tubes (3, 10).
(d) Do not remove the bushings (5, 6) from the lugs of the bellc rank assembly.
(3) Assemble the bellcrank assembly as follows:
(a) Apply a thin layer of grease CM 115 to the tubes (2, 3, 10) an d to the screw (1).
(b) Hold the bellcrank Q (11), the bellcrank K (13) and the bel lcrank L (15) in their
installation positions between the lugs of the bearing bloc k (4). Refer to the marks
Conf. Code: 000 67-13-00, 4-4 Page 401
2021.02.22
PRE PRINT

### Page 22

Aircraft Maintenance Manual (AMM) MBB BK117-C2
made during the removal procedure.
NOTE The length of the long arm of the bellcrank K (13) is between
89.8 mm and 90.2 mm (35.36 in and 35.51 in) (distance Y). The
length of the short arm of the bellcrank K (13) is between 67.8
mm and 68.2 mm (26.70 in and 26.85 in) (distance X).
1 Measure the bellcrank K (13) to identify the long arm. Make su re that the long
arms of the bellcrank Q (11), the bellcrank K (13) and the bell crank L (15) point
down.
NOTE The bellcrank Q (11) has a red mark (12). The bellcrank K (13)
has a white mark (14). The bellcrank L (15) has a black mark (
16). The color marks (12, 14, 16) are in the short arms pointin g
up.
2 Make sure that the color marks (12, 14, 16) of the bellcrank Q ( 11), the
bellcrank K (13) and the bellcrank L (15) point up.
(c) Make sure that you install them with the same orientation and in the same position
on the bearing block (4) where you removed them from.
NOTE The tube (10) is longer than the tube (3).
(d) Install the tubes (2, 3, 10). Refer to the marks made durin g the removal procedure.
(e) Make sure that you install them in the same position on the bearing block (4), where
you removed them from.
(f) Install the screw (1), the washer (9) and the nut (8).
(g) Apply a torque between 22 Nm and 27 Nm (195 lbf.in to 238 lbf .in) to the nut (8).
(h) Safety the nut (8) with a new split pin (7).
(i) Apply a thin layer of grease CM 115 on the visible threads o f the bolt (1), the
surfaces of the washer (9) and the nut (8).
G. Close-up:
(1) Install the bellcrank assembly (67-13-00, 4-3).
(2) Remove all tools and other materials and clean the work ar ea.
Conf. Code: 000 67-13-00, 4-4 Page 402
2021.02.22
PRE PRINT

### Page 23

Aircraft Maintenance Manual (AMM) MBB BK117-C2
(195−238 lbf.in)
BKC26713M104100MU04
B
22−27 Nm
B
C
C
X
Y
FWD
A
A
1
2
3
4
5
6
7
8
9
10
11
13
15
13
12
14
16
Disassembly / Assembly - Bellcrank Assembly
Figure 401
Conf. Code: 000 67-13-00, 4-4
END OF MODULE
Page 403
2021.02.22
PRE PRINT

### Page 24

Aircraft Maintenance Manual (AMM) MBB BK117-C2
Main Rotor Controls - Adjustment / Test
EFFECTIVITY ALL
5-3 Operational Test - Free Movement of the Main Rotor Contro ls
A. References:
29-00-00, 2-1 ................................. Connec t / Disconnect - External Pump Drive
52-40-00, 4-2 ................................. Remova l / Installation - Bottom Access Cover (FWD)
52-40-00, 4-3 ................................. Remova l / Installation - Bottom Access Cover (AFT)
52-50-00, 4-3 ................................. Remova l / Installation - Floor Access Covers
B. Special Tools:
None.
C. Consumable Materials:
None.
D. Routine Replacement Parts:
None.
E. Job Set-up:
(1) Remove the FWD bottom access cover (52-40-00, 4-2).
(2) Remove the AFT bottom access cover (52-40-00, 4-3).
(3) Remove the floor access covers as necessary (52-50-00, 4 -3).
NOTE The external pump drive can be connected to the hydraulic pow er system 1
or the hydraulic power system 2.
(4) Connect the external pump drive (29-00-00, 2-1).
(5) Make sure that you removed all the tools and the ground equ ipment from the areas that
follow:
- Below the cockpit floor
- On the roof around the modul plate assy
- At the main rotor
- In tail boom at intermediate gear box.
- At the tail rotor.
F. Procedure:
NOTE Two persons are necessary to do the steps that follow.
(1) Do the free movement test of the main rotor controls as fol lows:
(a) Switch on the external pump drive.
(b) Slowly move the copilot cyclic stick (3, Figure 501 ) and the copilot collective lever (
4) through their full range of travel for more than two times.
Conf. Code: 001 67-10-00, 5-3 Page 501
2021.03.08
PRE PRINT

### Page 25

Aircraft Maintenance Manual (AMM) MBB BK117-C2
1 Make sure that the copilot cyclic stick (3) and the copilot co llective lever (4)
move freely through their full range of travel.
2 Make sure that the copilot collective lever (4) does not touc h other components
and/or the wiring.
3 Make sure that there is sufficient clearance between the fee dthrough of
airframe for complete stroke of affected axis.
(c) Slowly move the pilot cyclic stick (1) and the pilot colle ctive lever (2) through their
full range of travel for more than two times.
1 Make sure that the pilot cyclic stick (1) and the pilot collec tive lever (2) move
freely through their full range of travel.
2 Move the pilot collective lever (2) to its lowest position. M ake sure that the pilot
collective lever (2) does not touch the end stop on the floor.
3 Make sure that the pilot collective lever (2) does not touch o ther components
and/or the wiring.
4 Make sure that there is sufficient clearance between the fee dthrough of
airframe for complete stroke of affected axis.
5 Measure the clearance between the locking pin (6) of the pilo t collective lever (
2) and the collective lever fixation (5). Make sure that the m inimum clearance
between the locking pin (6) of the pilot collective lever (2) and the collective
lever fixation (5) is 4 mm (0.158 in).
(d) Slowly move the pedals throught its full range of travel f or more than two times.
1 Make sure that the pedals move freely throught their full ran ge of travel.
2 Measure the clearance between the tail rotor flexball conne ction (8) and the
floor (7) at pedal side. Make sure that the clearance between the tail rotor
flexball connection (8) and the floor (7) at pedal side is mor e than or equal to 3
mm (0.12 in).
(e) Do a check of the clearance between the control levers (2, Figure 502 ) and the
swash plate (1) as follows:
1 Put the copilot cyclic stick (3, Figure 501 ) and the pilot cyclic stick (1) in the
forward left position.
2 Pull up the pilot collective lever (2) and the copilot collec tive lever (4).
3 Manually turn the main rotor one full turn.
a Make sure that there is sufficient clearance at the rotor bla des.
b Measure the clearance between the control levers (2, Figure 502 ) and the
swash plate (1).
c Make sure that the minimum clearance between the control lev ers (2) and
the swash plate (1) is 1.5 mm (0.06 in).
d Make sure that the fasteners of the cable tie and the bellow se am, if
installed, are not in the driving link area.
4 Put the copilot cyclic stick (3, Figure 501 ) and the pilot cyclic stick (1) in the
forward left position.
Conf. Code: 001 67-10-00, 5-3 Page 502
2021.03.08
PRE PRINT

### Page 26

Aircraft Maintenance Manual (AMM) MBB BK117-C2
5 Push down the pilot collective lever (2) and the copilot coll ective lever (4).
6 Manually turn the main rotor until the driving link is approx imately at a 4 o’clock
position (1, Figure 503 ). Hold this position.
a Check the clearance between swashplate bellows, if install ed, and driving
link, a force free contact is permitted.
7 Put the copilot cyclic stick (3, Figure 501 ) and the pilot cyclic stick (1) in the
forward right position.
8 Push down the pilot collective lever (2) and the copilot coll ective lever (4).
9 Manually turn the main rotor until the driving link is approx imately at a 5 o’clock
position (2, Figure 503 ). Hold this position
a Check the clearance between swashplate bellows, if install ed, and driving
link, a force free contact is permitted.
(f) In case of a failure during the free movement test such as c haffing or colision
between the affected parts, adjust and/or install the compo nents correctly and do
the free movement test again as given above.
(g) Make sure that all the components of the flight control sy stem are fastened and
secured.
(h) Switch off the external pump drive.
G. Close-up:
(1) Disconnect the external pump drive (29-00-00, 2-1).
(2) If removed, install the floor access covers (52-50-00, 4 -3).
(3) Install the AFT bottom access cover (52-40-00, 4-3).
(4) Install the FWD bottom access cover (52-40-00, 4-2).
(5) Remove all tools and other materials and clean the work ar ea.
Conf. Code: 001 67-10-00, 5-3 Page 503
2021.03.08
PRE PRINT

### Page 27

Aircraft Maintenance Manual (AMM) MBB BK117-C2
min. 4 mm
            0.157 in
A
BKC26710M107000MU01
FWD
B
A
B
C
min. 3 mm
           0.118 in
C
1 2 3
4
2
6 5
8
7
Operational Test - Main Rotor Controls
Figure 501
Conf. Code: 001 67-10-00, 5-3 Page 504
2021.03.08
PRE PRINT

### Page 28

Aircraft Maintenance Manual (AMM) MBB BK117-C2
A
BKC26710M107100MU00
A
1.5 mm
(0.06 in)
1.5 mm
(0.06 in)
1
2
2
Operational Test - Free Movement of the Main Rotor Controls
Figure 502
Conf. Code: 001 67-10-00, 5-3 Page 505
2021.03.08
PRE PRINT

### Page 29

Aircraft Maintenance Manual (AMM) MBB BK117-C2
A
BKC26710M107200MU00
FWD A
FWD A
2
1
Driving Link Position (Stick Forward Left and Stick Forward Right)
Figure 503
Conf. Code: 001 67-10-00, 5-3
END OF MODULE
Page 506
2021.03.08
PRE PRINT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
