# Airbus Helicopters Alert Service Bulletin SA366-01.29

Copy: No revision named ("Airbus Helicopters ASB SA366 01.29 R5"), 23 pages: PDF https://openairdocs.org/files/sha256/c3/32/c332319d37e5786d308eb6d223e138e881cf3683f2cb85c846934b7435499ed2; text https://openairdocs.org/service-documents/airbus-helicopters/sa366-01-29/file/c332319d37e5.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1123, the docket of AD 2021-05-05. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md)
- Type: Service bulletin (Alert Service Bulletin)
- Number: SA366-01.29
- Page: https://openairdocs.org/service-documents/airbus-helicopters/sa366-01-29

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-23-05](https://openairdocs.org/ad/2016-23-05.md), effective Dec 12, 2016: No revision named

## Text (23 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1123, the docket of AD 2021-05-05. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
Civil version (s): G1
Military version (s): GA
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
LIMITATIONS - Control rod double bearing
Tail Gearbox (TGB)
ATA: 65
For the attention of
Revision No.  Date of issue
Revision 0  2016-05-04
Revision 1  2016-06-03
Revision 2  2016-10-28
Revision 3  2017-07-20
Revision 4  2019-12-11
Revision 5  2020-03-25
Summary:
- Periodic replacement of the TGB control rod double bearing on PRE MOD 07 65B63 TGBS.
- Pending the next replacement of the control rod double bearing, reducing the inspection interval for the TGB
magnetic plug to ensure that there are no particles, and removing the control shaft/rod assembly once or twice
(depending on the case) to inspect the double bearing.
- Maintaining the TGB operating oil at the maximum level.
Compliance with this ALERT SERVICE BULLETIN supersedes the instructions specified in SA366 ALERT
SERVICE BULLETIN No. 05.41.
Reason for last revision:
Following experience feedback (flight hours cumulated and chip events) which allowed
Airbus Helicopters to review the global detection performances of the bearing degradation on POST MOD 65B63
TGBs, ALERT SERVICE BULLETIN No. 01.31 has been revised to reduce the interval of
the chip detector inspection.
As a precautionary measure, Airbus Helicopters is also reducing the interval of the chip
detector inspection on PRE MOD 65B63 TGBs.
This protective measure is a temporary measure.
Compliance:
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory.  ASB SA366-01.29
Revision 0 2016-05-04  Page 1/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 2 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
On PRE MOD 07 65B63 Tail Gearboxes (TGB).
NOTE 1
Series modification 07 65B63 creates a new TGB Part
Number 365A33-6005-09 enabling the instructions of this
ALERT SERVICE BULLETIN to be canceled.
Helicopters which embody MOD 07 65B63 are not
concerned by the instructions given in this ALERT SERVICE
BULLETIN.
1.A.2. Non-installed equipment or parts
On PRE MOD 07 65B63 TGBs.
On PRE MOD 07 65B57 double bearings.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
Revision 0:
Airbus Helicopters has recently participated in investigations following an accident that was due to the loss of
yaw control on an AS365 N3 helicopter.
This helicopter had been subject to periodic checks carried out in accordance with the instructions given in
Revision 4 of ALERT SERVICE BULLETIN No. 05.41.
The preliminary examination of the TGB revealed that the control rod double bearing was damaged.
Investigations are ongoing to determine the cause of this damage and the reasons for its non-detection.
In order to prevent the risk of undetected double bearing damage, Airbus Helicopters makes compliance with
the instructions given in this ALERT SERVICE BULLETIN mandatory, the purpose of which is:
- To ensure that the TGB lubricating oil level is at the "max" level,
- To periodically replace the control rod double bearing on TGBs that do not embody the latest
modification,
- pending the next replacement of the control rod double bearing, to check more frequently that there are
no particles at the TGB magnetic plug, and to remove the control shaft/rod assembly once or twice
(depending on the case) for inspection of the double bearing,
- And to cancel compliance with ALERT SERVICE BULLETIN No. 05.41.
Revision 1:
Following the issue of Revision 0 of this ALERT SERVICE BULLETIN, Airbus Helicopters would like to add
some details to paragraph 1.E.2.a.2. concerning the check of the magnetic plug
Furthermore, in order to analyze the possibility of increasing the interval between periodic replacements of
POST MOD 07 65B57 bearings, Airbus Helicopters requests the return of some bearings.
A bearing monitoring sheet has therefore been added in appendix paragraph 4.B. It must be filled in and
returned to Airbus Helicopters during the next replacement following the issue of this ALERT SERVICE
BULLETIN
In addition, a flow chart has been added to paragraph 2.D. This flow chart explains the process for returning
bearings and the monitoring sheet given in Appendix 4.B. to Airbus Helicopters.
Revision 0  2016-05-04  Page 2/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 3 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
Revision 2:
Following the issue of Revisions 0 and 1 of this ALERT SERVICE BULLETIN, Airbus Helicopters wishes to
clarify paragraph 1.E.2. concerning the embodiment of MOD 07 65B56 or 07 65B58.
These MODs improve the sliding action of the control rod assembly in the TGB, by installing new guide rings.
MOD 07 65B56 is embodied on all new TGBs and during Overhaul (RG).
MOD 07 65B58 may be embodied through SA366 Service Bulletin No. 65.04 or during repair (RE). Airbus
Helicopters reminds you that it was mandatory to embody MOD 07 65B58 before September 30, 2011,
following the issue of SA366 ALERT SERVICE BULLETIN No. 05.41 Revision 1 dated July 13, 2011.
Airbus Helicopters requests that you check for the presence of new guide rings when replacing the double
bearing.
Revision 3:
Since the issue of Revision 2, complementary tests have been performed on particle detection in the TGB.
In order to ensure an earlier detection of a potential degradation of the double bearing Airbus Helicopters
revised the current inspection and close monitoring procedure for PRE MOD 07 65B63 TGBS:
- the inspection interval for the electrical magnetic plug is changed from 100 flying hours to
25 flying hours, as for the manual magnetic plug,
- Modification of the procedure after detection of particles as scale, flake, splinter or abrasion at the TGB
magnetic plug in order to identify quickly and more efficiently a double bearing degradation. Now, when
detection of these types of particles in the TGB, a metallurgical analysis or a complete cleaning of the TGB
is required.
In addition, a calendar limitation is introduced in order to ensure that POST MOD 07 65B63 will be the
standard on all TGB after 01/01/2024.
Revision 3 does not affect compliance with the previous revisions of this ALERT SERVICE BULLETIN.
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory.
Revision 4:
The purpose of revision 4 is:
- To improve the washing procedure for the double bearing of the TGB control rod,
- To specify the commercial conditions related to the return of the bearings in paragraph 2.D,
- To remind customers to be cautious with abrasion particles (class g in the MTC).
Revision 0  2016-05-04  Page 3/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 4 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
Revision 5:
Following experience feedback (flight hours cumulated and chip events) which allowed Airbus Helicopters to
review the global detection performances of the bearing degradation on POST MOD 65B63 TGBs, ALERT
SERVICE BULLETIN No. 01.31 has been revised to reduce the interval of the chip detector inspection.
As a precautionary measure, Airbus Helicopters is also reducing the interval of the chip detector inspection
on PRE MOD 65B63 TGBs.
The purpose of revision 2 is to introduce this reduction of interval on the chip detector to 20 FH for bearings
with less than 250 FH and 10 FH for bearing with more than 250 FHs to improve detection of the particles.
This protective measure is a temporary measure.
Airbus Helicopters takes advantage of this revision to modify Appendix 4.B. to mention the type of oil used
and its manufacturer
1.D. DESCRIPTION
The purpose of this ALERT SERVICE BULLETIN is to periodically replace the double bearing of the TGB
control rod
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
1.E.2.a. Helicopters/installed equipment or parts:
NOTE 2
A flow chart which describes the maintenance operations
required by this ALERT SERVICE BULLETIN is also available
in Appendix 4.A.
1.E.2.a.1. Check of the TGB oil level
- Comply with paragraph 3.B.1. during each check after the last flight of the day (ALF).
Revision 0  2016-05-04  Page 4/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 5 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
1.E.2.a.2. Check of the TGB manual magnetic plug or magnetic plug with electrical indicating
- Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with paragraph 3.B.2. after each last flight of the day, pending the next replacement of the
double bearing following the issue of Revision 0 of this ALERT SERVICE BULLETIN on May 4, 2016.
- Then, after replacement of the double bearing:
• For the manual magnetic plug:
. For double bearings with less than 250 FH:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. within 20 FH without exceeding the scheduled
Then,
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 20 FH
• For double bearings with 250 FH or more:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. within 10 FH without exceeding the scheduled
inspections of the magnetic plug.
Then,
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 10 FH
• For the magnetic plug with electrical indicating:
. For double bearings with less than 250 FH:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. within 20 FH without exceeding 25 FH since the
last inspection,
Then,
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 20 FH
• For double bearings with 250 FH or more:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. within 10 FH without exceeding 25 FH since the
last inspection,
Then,
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and
comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 10 FH
Revision 0  2016-05-04  Page 5/23
Revision 5 2020-03-25  This document is available on the internet: www.airbus  oters.com/techpub/

### Page 6 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
1.E.2.a.3. For all TGBs
- For all helicopters which comply with Revision 0 or 1 of this ALERT SERVICE BULLETIN:
. check for the MOD 07 65B56 or 07 65B58 indication on the TGB Log Card (FM):
- if one of these MODs is indicated, leave as is,
- if neither of these MODs is indicated, comply with SA366 Service Bulletin No. 65.04.
- For helicopters which do not comply with Revision 0 or 1 of this ALERT SERVICE BULLETIN:
CAUTION
WE REMIND YOU THAT IT IS MANDATORY TO
COMPLY  WITH  THE  INSTALLATION
INSTRUCTIONS AND TO USE THE SPECIFIC
TOOLS  FOR  DOUBLE BEARING
REPLACEMENT.
CAUTION
WHEN REPLACING THE DOUBLE BEARING,
ENSURE THAT EMBODIMENT OF MOD 0765B56
OR 0765B58 HAS BEEN RECORDED ON THE TGB
LOG CARD (FM).
a) For PRE MOD 07 65B57 double bearings of the control shaft/rod assembly
NOTE 3
MOD 07 65B57 consists in introducing a new double bearing
(MP/N 704A33-651-245 or 704A33-651-246 depending on
the manufacturer).
This new double bearing:
- has an optimized design which favors the evacuation of
particles,
- has a reinforced structure,
- is interchangeable with a PRE MOD 07 65B57 double
bearing (MP/N 704A33-651-093 or 704A33-651-104
depending on the manufacturer).
1) For new double bearings or double bearings which have logged less than 335 flying hours
. At the latest when 350 flying hours are reached, replace the PRE MOD 07 65B57 double
bearing with a POST MOD 07 65B57 double bearing as per SA366 Service Bulletin
No. 65.05,
.. When replacing the bearing, comply with paragraph 2.D.
. Then comply with paragraph 1.E.2.a.3.b)1)
Revision 0 2016-05-04
Revision 5 2020-03-25  This document is available on the interet: www.airbushelicopters.com/techpub/

### Page 7 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
2) For double bearings which have logged 335 or more flying hours
. Replace the PRE MOD 07 65B57 double bearing with a POST MOD 07 65B57 double bearing
as per SA366 Service Bulletin No. 65.05 within 110 flying hours following receipt of this ALERT
SERVICE BULLETIN Revision 0, issued on the date indicated at the bottom of the page:
.. Pending the replacement of the double bearing, comply with paragraph 3.B.3. within
15 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued on the
date indicated at the bottom of the page,
Then,
.. Comply with paragraph 3.B.3. every 55 flying hours maximum until the double bearing is
replaced.
.. When replacing the bearing, comply with paragraph 2.D.
. Then comply with paragraph 1.E.2.a.3.b)1)
b) For POST MOD 07 65B57 double bearings of the control shaft/rod assembly
NOTE 4
MOD 07 65B57 consists in introducing a new double bearing
(MP/N 704A33-651-245 or 704A33-651-246 depending on
the manufacturer).
This new double bearing:
- has an optimized design which favors the evacuation of
particles,
- has a reinforced structure,
- is interchangeable with a PRE MOD 07 65B57 double
bearing (MP/N 704A33-651-093 or 704A33-651-104
depending on the manufacturer).
1) For new double bearings or double bearings which have logged less than 485 flying hours
. At the latest when 500 flying hours are reached, replace the double bearing as per Mechanical
Repair Manual (MRM) Work Card 65-21-00-702.
.. When replacing the bearing, comply with paragraph 2.D.
• Then, replace the double bearing every 500 flying hours as per Work Card 65-21-00-702
(MRM).
2) For double bearings which have logged more than 485 flying hours
Replace the double bearing within 110 flying hours following receipt of this ALERT SERVICE
BULLETIN Revision 0, issued on the date indicated at the bottom of the page:
..Pending the replacement of the double bearing, comply only once with paragraph 3.B.3.
within 15 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued
on the date indicated at the bottom of the page,
.. When replacing the bearing, comply with paragraph 2.D.
. Then, replace the double bearing every 500 flying hours as per Work Card 65-21-00-702
(MRM).
1.E.2.a.4. Helicopters equipped with a TGB PRE MOD 07 65B63 will be unfit for flight from January 01, 2024.
Revision 0 2016-05-04  Page 7/23
Revision 5 2020-03-25  This document is available on the internet: www.airbush  elicopters.com/techpub/

### Page 8 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
1.E.2.b. Non-installed equipment or parts:
CAUTION
WHEN  REPLACING  THE DOUBLE BEARING,
ENSURE THAT EMBODIMENT OF MOD 0765B56
OR 0765B58 HAS BEEN RECORDED ON THE TGB
LOG CARD (FM).
- It is prohibited to install PRE MOD 07 65B57 double bearings on TGBs from receipt of this ALERT
SERVICE BULLETIN issued on the date indicated at the bottom of the page.
- On TGBS equipped with a PRE MOD 07 65B57 double bearing:
Before installation on the helicopter, replace the control rod double bearing with a POST MOD 07 65B57
double bearing as per SA366 Service Bulletin No. 65.05.
- On TGBs equipped with a POST MOD 07 65B57 double bearing:
Comply with the instructions given in paragraph 1.E.2.a.3.b)
- Do not install TGB PRE MOD 07 65B63 after January 01, 2024.
1.F. APPROVAL
Approval of modifications:
The information or instructions related to modification 07 65B57 were approved on April 18, 2012 by the
EASA for helicopters of civil versions subject to an Airworthiness Certificate.
The information or instructions related to modification 07 65B57 were approved on May 14, 2012 by the
Airbus Helicopters Airworthiness Department for export military versions.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved
on May 04, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of
civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN revision 0 was approved
on May 04, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on June 03, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of
civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved
on June 03, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved
on October 28, 2016 under the authority of EASA Design Organization Approval No. 21J.700 for helicopters
of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved
on October 28, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
Revision 0 2016-05-04  Page 8/23
Revision 5 2020-03-25  This document is available on the internet: www.a  licopters.com/techpub/

### Page 9 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
The technical information contained in this ALERT SERVICE BULLETIN Revision 3 was approved
on July 19, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 3 was approved
on July 19, 2017 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 4 was approved
on December 10, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for civil
version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 4 was approved
on December 10, 2019 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 5 was approved
on March 24, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil version
helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 5 was approved
on March 24, 2020 by the Airbus Helicopters Airworthiness Department for export military versions.
1.G. MANPOWER
For compliance with this Service Bulletin, Airbus Helicopters recommends the following staff qualifications:
Qualification:
- 1 Mechanical Engineering Technician
Or
- 1 pilot with the appropriate training and certification for compliance with paragraph 3.B.1.
For compliance with paragraphs 3.B.2. and 3.B.3., the mechanical engineering technician qualification is
mandatory.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter
configuration.
Estimated Man-hours:
For compliance with paragraph 3.B.1.: approximately 30 minutes.
For compliance with paragraph 3.B.2.: approximately 1 hour (excluding metallurgical analysis).
For compliance with paragraph 3.B.3.: approximately 8 hours.
Approximately 2 days to replace the double bearing.
Estimated helicopter downtime:
Helicopter downtime is estimated at 2 days.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
Revision 0 2016-05-04  Page 9/23
Revision 5 2020-03-25  This document is available on the interet: www.airbushelicopters.com/techpub/

### Page 10 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
1.K. REFERENCES
Maintenance Manual (MET) Work Cards:
05-53-00-201 - 12-00-00-308 - 12-00-00-601 - 65-21-00-402
Mechanical Repair Manual (MRM) Work Cards:
65-21-00-701 - 65-21-00-702
Standard Practices Manual (MTC) Work Card:
20-04-01-102 - 20-08-01-601
SA366 Service Bulletin No. 65.04
SA366 Service Bulletin No. 65.05
1.L. OTHER AFFECTED PUBLICATIONS
Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
Revision 0 2016-05-04  Page 10/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 11 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
The bearings will be supplied free of charge by the Airbus Helicopters Programs Department.
Specify the helicopter serial number when placing your order.
For any information concerning the kits or components or for assistance, contact the Airbus Helicopters
Network Sales & Customer Relations Department.
Order as required from:
Airbus Helicopters
Etablissement de Marignane
Direction Ventes et Relations Client
13725 MARIGNANE CEDEX
FRANCE
NOTE 1
On the purchase order, please specify the mode of
transport, the destination and the serial numbers of the
helicopters to be modified.
NOTE 2
For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F
Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION
For any information concerning modification kits and/or components or for assistance, contact the Airbus
Helicopters Network Sales and Customer Relations Department.
Revision 0 2016-05-04  Page 11/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 12 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Kits or components to be ordered for one helicopter or one assembly:
Former
Designation  Qty  New P/N  Item
PIN  →  Instruction
Double bearing
((FAG) POST  704A33-651-245  1  To be replaced
MOD 07 65B57)
Or
Double bearing
((SNR) POST  1  704A33-651-246  To be replaced
MOD 07 65B57)
Consumables to be ordered separately:
As per the Work Cards specified in this ALERT SERVICE BULLETIN and the list below:
Designation  Qty  Consumable P/N  Item
WHITE SPIRIT  AVR  Off the shelf  2
The consumables can be ordered separately from the following companies.
Aviatec global aviation
Website: https://www.aviatec.net
Telephone: +33 1.34.46.45.24 or +49 4193.8803.630
Fax: +33 1.34.46.45.26 or +49 4193.8803.699
AOG: +49 4193.8803.660
AOG email: aog@aviatec.aero
BDSI
Website: https://www.boeingdistribution.com
Telephone: +1.305.925.2600
Fax: +1.305.507.7191
AOG: +1.305.471.8888
AOG email: AOGdesk@Boeingdistribution.com
Gaches chimie
Website: https://www.gaches.com
Telephone: +33 5.61.31.64.45
Fax: +33 5.61.40.98.63
AOG email: marketplace@gaches.com
Revision 0 2016-05-04  Page 12/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 13 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
2.D. EQUIPMENT OR PARTS TO BE RETURNED
- Return the bearing monitoring sheet given in APPENDIX 4.B. to the Airbus Helicopters Technical Support:
Fax:  +33 (0)4.42.85.99.66
E-mail: support.technical-dyncomp.ah@airbus.com or TechnicalSupport.Helicopters@airbus.com)
- In accordance with the flow chart below, return the double bearing to the Airbus Helicopters Technical
Support at the following address:
Airbus Helicopters
Aéroport Marseille Provence
RETEX Factory - roulement double de BTA
MAH09MGA2 - B1 - LES BORIES
SOUS SOL - ARRIVEE
13725 Marignane CEDEX
FRANCE
NOTE 3
The expenses for the return of the bearing to Airbus
Helicopters are supported by Airbus Helicopters.
Bearing
removal
PRE MOD  POST MOD
07 65B57  07 65B57
bearing  bearing
P/N: 704A33651.104  P/N: 704A33651.246
P/N: 704A33651.093  P/N: 704A33651.245
Correct  Presence of play  TSN ≤ 500 FH  TSN > 500 FH
condition  and/or particles
Correct  Presence of play
condition  and/or particles
Send the  Send the  Send the  Send the  Send the
monitoring sheet  monitoring sheet  monitoring sheet  monitoring sheet  monitoring sheet
given in  given in  given in  given in  given in
APPENDIX 4.B.  APPENDIX 4.B.  APPENDIX 4.B.  APPENDIX 4.B.  APPENDIX 4.B.
+ scrap the  + send the  + scrap the  + send the  + send the
bearing  bearing to  bearing  bearing to  bearing to
Airbus  Airbus  Airbus
Helicopters  Helicopters  Helicopters
Flow chart for the bearing return process
Revision 0 2016-05-04  Page 13/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 14 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
3. ACCOMPLISHMENT INSTRUCTIONS
3.А. GENERAL
Not applicable.
3.B. WORK STEPS
3.B.1. Checking the TGB oil level
- Make sure that the TGB oil level is at the "max" level,
Otherwise,
• Top up the TGB oil level to the "max" level before resuming flights, as per Work Card 12-00-00-308
(MET).
3.B.2. Checking the TGB manual magnetic plug or magnetic plug with electrical indicating
A CAUTION
IN THE FLOW CHART, THE ABRASION PARTICLES
(CLASS g AS PER MTC) MUST BE TAKEN INTO
ACCOUNT IN ADDITION TO THE PARTICLE TYPES
USUALLY TAKEN INTO ACCOUNT.
_ abrasion
Figure 1: Example of abrasion on the magnetic plug
Revision 0  2016-05-04  Page 14/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 15 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
Check the TGB magnetic  Presence of
plug as per Work  particles?  Resume flights
Card 12-00-00-601 (MET).  No
' Reminder: complete the "PARTICLE
DETECTION" follow-up sheet as per Work
Card 20-08-01-601 (MTC).
CAUTION
In this special case, abrasion-type particles
(class g as per MTC) must be taken into
account.
Yes
Comply with § F.2.a/b/c of Work Card 05-53-00-201 (MET).
Characterize particle(s) as per Work Card 20-08-01-601.
** If the collected particles are not clearly
characterized, perform a metallurgical analysis
and contact Airbus Helicopters
(support.technical-dyncomp.ah@airbus.com or
TechnicalSupport.Helicopters@airbus.com)  Is a module removal  Yes  Remove the TGB in
before resuming flights.  criterion reached as per  accordance with technical
MTC 20.08.01.601?  publications
Other names for material M50:
AMS6490  • No
80DCV40
Any abrasion/scale/flake/
Comply with Work  splinter/abrasion or particle
Card 20-08-01-601 (MTC)  different from cotter pins,
procedures provided in SIN No.  3095-S-63.*  No  metallic debris? **  lockwire, swart, various non-
Yes
≤ 25 flying hours  What is the TSN Time Since  > 25 flying hours
New) of the double bearing?
Continue flights for 25 hours maximum, then  Stop flights and carry out one of the
carry out one of the following inspections.  following inspections.
OR
Carry out a metallurgical analysis of all  Comply with paragraph 3.B.3.
particles collected since the installation
of the bearing.
Resume flights with close  Presence of
monitoring as per Work  No  play or
M50***  Presence of  No  Card 05-53-00-201  (MET) and comply with  particles?
particles?  paragraph 3.B.2. for the
collected particles.
Yes
Yes
- Replace double bearing (d) (Figure 2) with a double bearing (1) as per Work Card 65-21-00-702 (MRM).
- Inform Airbus Helicopters using the contact details given in NOTE 1 on the next page.
Revision 0  2016-05-04  Page 15/23
Revision 5  2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 16 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
NOTE 1
Airbus Helicopters Technical Support Department:
Fax: + 33(0)4.42.85.99.66
E-mail:  support.technical-dyncomp.ah@,airbus.com  or
TechnicalSupport.Helicopters@airbus.com)
Keycopter: Technical Request Management
3.B.3. Checking the play in the double bearing of the TGB control shaft/rod assembly (Figure 2)
- Remove the control shaft/rod assembly as per paragraph 3.B.4.a.
- Carry out a tactile check to ensure that there is no axial play in double bearing (d) (Figure 2):
• Apply an alternating manual axial load to control rod (c) whilst turning control shaft (b) (See DETAIL A
Figure 2).
3.B.3.a.  If no play is felt:
- Clean the control shaft/rod assembly using WHITE SPIRIT (2) as per Work Card 20-04-01-102 (MTC):
1) Inject WHITE SPIRIT (2) under pressure (for example using a can) into hole (a) of control shaft (b).
(See DETAIL B Figure 2).
• Hold shaft (b) in the vertical position pointing upwards.
. Manually turn control rod (c) several times to rinse double bearing (d) by draining the WHITE
SPIRIT (2) through the bearing. (See DETAIL B Figure 2)
• Collect the WHITE SPIRIT (2) on absorbent paper (e.g.: blotting paper).
- Pass a magnet over the absorbent paper to collect the magnetic particles.
2) Insert WHITE SPIRIT (2) (for example using a can) in the area of the control shaft (b) that must be
cleaned. (See DETAIL C Figure 2).
. Manually turn the control rod (c) several times to wash the double bearing (d) by draining the
WHITE SPIRIT (2).
. Collect the WHITE SPIRIT (2) on an absorbent paper (e.g. blotting paper):
- Pass a magnet over the absorbent paper to collect the magnetic particles.
NOTE 2
Make sure that the area pointed out in DETAIL C Figure 2 is
clean.
3) Repeat operation No. 1).
NOTE 3
As double bearing (d) is "pre-stressed" by definition, friction
points can be felt when turning double bearing (d): they are
not critical.
Revision 0 2016-05-04  Page 16/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 17 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
• If there are no magnetic particles or magnetic abrasion dust:
- Install the control shaft/rod assembly as per paragraph 3.B.4.b.
If there are magnetic particles or magnetic abrasion dust:
Replace double bearing (d) with a double bearing (1) as per Work Card 65-21-00-702 (MRM).
Install the control shaft/rod assembly as per paragraph 3.B.4.b.
• Inform the Airbus Helicopters Customer Service Technical Support Department in
accordance with paragraph 2.B.
. Comply with paragraph 2.D.
3.B.3.b. If play is felt:
- Replace double bearing (d) (Figure 2) with a double bearing (1) as per Work Card 65-21-00-702 (MRM).
- Install the control shaft/rod assembly as per paragraph 3.B.4.b.
• Inform the Airbus Helicopters Customer Service Technical Support Department in accordance
with paragraph 2.B.
. Comply with paragraph 2.D.
3.B.4. Removal / Installation of the TGB control shaft/rod assembly
3.B.4.a. Removal of the TGB control shaft/rod assembly
CAUTION
BEFORE PERFORMING ANY OPERATION ON THE
TAIL ROTOR HUB (TRH) ASSEMBLY, LOCK THE
DRIVE SYSTEM WITH THE ROTOR BRAKE.
Remove the TGB control shaft/rod assembly as per Work Card 65-21-00-701 (MRM).
NOTE 4
Work Card 65-21-00-701 (MRM) refers to the procedure for
removing (if necessary) the double bearing as per Work
Card 65-21-00-702 (MRM). Only remove the double bearing
if there are doubts concerning its integrity.
NOTE 5
Work Card 65-21-00-701 (MRM) describes the procedure for
checking the pitch-change spider  interchangeability
dimension. Reminder: this procedure is only required if the
pitch-change spider is replaced.
Revision 0 2016-05-04  Page 17/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 18 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
3.B.4.b. Installation of the TGB control shaft/rod assembly
CAUTION
PARTICULAR CARE MUST BE TAKEN WHEN
CLEANING AND INSTALLING PARTS IN ORDER TO
PREVENT CREATING ANY CONTAMINATION.
- Check that there are no particles in the TGB cover lubrication hole.
- Install the TGB control shaft/rod assembly as per Work Card 65-21-00-701 (MRM).
3.C. RECORD OF COMPLIANCE
Compliance with this document:
- Record first compliance with paragraph 3.B.1. of this ALERT SERVICE BULLETIN in the helicopter
documents.
- Record first compliance with paragraph 3.B.2. of this ALERT SERVICE BULLETIN on the TGB Log Card
(FM).
- If necessary, record first compliance with paragraph 3.B.3. of this ALERT SERVICE BULLETIN on the TGB
Log Card (FM).
Tracking of modifications in the documentation:
- When replacing the PRE MOD 07 65B57 double bearing with a POST MOD 07 65B57 double bearing,
record the embodiment of MOD 07 65B57 on the TGB Log Card (FM).
- Please confirm compliance with this ALERT SERVICE BULLETIN:
QR-Code or hypertext link
NOTE 6
The recording of compliance with ALERT SERVICE
BULLETINS in the R-Tex tool does not replace the recording
in the helicopter documents.
ASB SA366-01.29
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
Revision 0 2016-05-04  Page 18/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 19 (OCR)

* AIRBUS
HELICOPTERS  ASB No. SA366-01.29
DETAIL B
C
DETAIL A  DETAIL C
Area to be cleaned
Return to paragraph 3.B.3.
Figure 2
Revision 0  2016-05-04  Page 19/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 20 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-05-04  Page 20/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 21 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
4. APPENDIX
4.A. Process for compliance with paragraph 1.E.2.a.
If the TGB is PRE MOD 07 65B63
Maintain the TGB oil level at its  Bearing replacement  Check of the magnetic plug (paragraph 3.B.2.)
maximum (paragraph 3.B.1.)  Pending next double bearing replacement,
during ALF  during ALF.
After bearing replacement:
every 20 FH if the double bearing has
If the control rod bearing is  If the control rod bearing is  cumulated less than 250 FH,
PRE MOD 07 65B57  POST MOD 07 65B57  every 10 FH if the double bearing has
cumulated 250 FH or more.
For new bearings or bearings  For bearings which have  For new bearings or bearings  which have logged less than  logged more than 485 FH  For bearings which have
which have logged less than  logged more than 335 FH  485 FH
335 FH
At the latest when 350 FH are  Within 110 FH following  At the latest when 500 FH  Within 110 FH following receipt of
reached, replace the PRE MOD  receipt of ASB Rev. 0, replace  are reached, replace the  ALERT SERVICE BULLETIN Rev. 0,
07 65B57 bearing with a POST  the PRE MOD 07 65B57  bearing with a POST MOD  replace the bearing with a POST MOD
MOD 07 65B57 bearing.  bearing with a POST MOD  07 65B57 bearing  07 65B57 bearing.
07 65B57 bearing.
Then replace the POST MOD  Then replace the bearing  Then replace the bearing every
bearing every 500 FH.  Then replace the POST MOD  every 500 FH.  500 FH.
bearing every 500 FH.
Pending the bearing replacement:
Pending the bearing replacement:  Within 15 FH following receipt ol  receipt of ALERT  Within 15 FH followina
ALERT SERVICE BULLETIN Rev. 0  SERVICE BULLETIN
perform a bearing play inspection with  Rev. 0, perform a bearing
disassembly (paragraph 3.B.3.)  Every 55FH since latest inspection,  disassembly (paragraph  olav inspection with
perform a bearing play inspection with  3R31
disassembly.
Revision 0  2016-05-04  Page 21/23
Revision 5  2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 22 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
PAGE LEFT BLANK INTENTIONALLY
Revision 0 2016-05-04  Page 22/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

### Page 23 (OCR)

AIRBUS
HELICOPTERS  ASB No. SA366-01.29
4.B. Bearing behavior monitoring sheet to be filled in and returned
Behavior monitoring sheet
P/N:
S/N:  Date of removal:
Version:
TSN/TSO:  P/N:
Customer:  TGB control rod
Helicopter  S/N:  TGB  Oil brand:  bearing  S/N:
Type of mission:  Oil reference:
Flying hours:
Please enclose the TGB Log
Card.
Condition of the bearing  Decision
Correct condition:  Presence of axial play:  Presence of particles:  Bearing to be sent to AH
Yes / No  Yes• / No •  Yes• / No •  Yes_ / No •
Revision 0 2016-05-04  Page 23/23
Revision 5 2020-03-25  This document is available on the internet: www.airbushelicopters.com/techpub/

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
