# Eurocopter Alert Service Bulletin 380

Copy: No revision named ("U.S. DOT/FAA - Eurocopter ASB_380_EN"), 18 pages: PDF https://openairdocs.org/files/sha256/c4/ad/c4ad883450e21bba7e5f6390351b0cf0115b086b78bfbb7360462ee22b67c258; text https://openairdocs.org/service-documents/airbus-helicopters/sb-380/file/c4ad883450e2.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2011-1408, the docket of AD 2012-18-08. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Alert Service Bulletin)
- Number: 380
- Page: https://openairdocs.org/service-documents/airbus-helicopters/sb-380

## Text (18 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2011-1408, the docket of AD 2012-18-08. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 1/18 
2007.03.22 
 
EUROCOPTER  
DIRECTION TECHNIQUE SUPPORT 
13725 MARIGNANE  CEDEX FRANCE 
 
EMERGENCY 
ALERT SERVICE BULLETIN 
 
SUPER PUMA NUMBER VERSIONS 
Civil:  C, C1, L, L1, L2 
332 76.00.04 Military: B, B1, F1, M, M1 
 
532 76.00.03 Military: AC, AL, SC, UC, UE, UL, A2, U2 
 
PUMA NUMBER VERSIONS 
Civil:  F, G, J 
330 76.03 Military: Ba, C, Ca, Ea, H, Jm, S1, Sm 
 
 
 
 
SUBJECT: ENGINE CONTROLS 
 
 Fuel Shut-Off Control Lever  – Tangential Gearbox Jamming 
 
 
 
REVISION No. DATE OF APPROVAL DATE OF ISSUE 
   
   
Revision 0 On: March 21, 2007 2007.03.21 
Revision 1 On: March 22, 2007 2007.03.22

### Page 2

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 2/18 
2007.03.22 
 
 
 
1. PLANNING INFORMATION  
 
1.A. EFFECTIVITY 
 
1.A.1. Helicopters / Installed equipment 
 
Helicopters fitted with tangential gearboxes. 
 
1.A.2. Non-installed equipment 
 
Not applicable. 
 
 
1.B. ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C. REASON 
 
To ensure that the fuel shut-off controls can be actuated, and to grease-lubricate the tangential 
gearboxes. 
 
The purpose of Revision 1 is to give a compliance time of 15 flying hours from receipt of Revision 0 of 
this ALERT SERVICE BULLETIN for helicopters that are 4 years old or older. 
 
Revision 1 of this ALERT SERVICE BULLETIN will form the subject of an EASA Airworthiness 
Directive.  
 
 
1.D. DESCRIPTION 
 
During a scheduled check (specified in the (PRE) Maintenance Program) of the fuel shut-off controls 
on two helicopters, one of the fuel shut-off controls was found to be jammed, which means that it 
would be impossible to actuate the general cut-off control. Both these helicopters are more than 20 
years old. 
 
The investigations have revealed that the jamming originates from the tangential gearboxes. In both 
cases, the grease in the left tangential gearbox had grown hard, and in one of these two cases, the 
right tangential gearbox showed traces of extensive corrosion. 
 
Jamming of the fuel shut-off control prevents: 
- the fuel cock at the engine inlet from closing and may thus stoke a fire, 
-the engine compartment ventilation flap from closing, which can reduce the efficiency of the 
extinguishing agent in the event of firing after fire alarm, 
- operation of the general cut-off control so that switching-off the electrical power system may become 
impossible in the event of an emergency landing.  
 
Consequently, EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory 
in order to ensure that it is possible to actuate the fuel shut-off controls and to grease-lubricate the 
tangential gearboxes.

### Page 3

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 3/18 
2007.03.22 
 
 
 
 
1.E. COMPLIANCE 
 
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory. 
 
1.E.1. Compliance at the works 
 
 Not applicable.  
 
1.E.2. Compliance in operation: By the operator: 
 
1.E.2.a. On helicopters / Installed equipment:  
 
For helicopters which are 4 years old or older: 
 
- Comply with paragraph 2.B.1. no later than within 15 flying hours following receipt of Revision 0 
of this ALERT SERVICE BULLETIN. 
 
. Interpretation of the results: 
 
- If there is no hard point in the fuel shut-off controls, comply with paragraph 2.B.1. at intervals 
not exceeding 50 flying hours pending compliance with paragraph 2.B.2. 
 
- If there is a hard point in one of the fuel shut-off controls, comply with paragraph 2.B.2. before 
resuming flights. 
 
- Comply with paragraph 2.B.2. no later than within 6 months following receipt of Revision 0 of this 
ALERT SERVICE BULLETIN. 
 
For helicopters which are less than 4 years old: 
 
-  When the helicopter is 4 years old, comply with paragraph 2.B.1. 
 
. Interpretation of the results: 
 
. If there is no hard point in the fuel shut-off controls, comply with paragraph 2.B.1. at intervals 
not exceeding 50 flying hours pending compliance with paragraph 2.B.2. 
 
. If there is a hard point in one of the fuel shut-off controls, comply with paragraph 2.B.2. before 
resuming flights. 
 
- Comply with paragraph 2.B.2. at the latest when the helicopter reaches 4 and a half years.  
 
1.E.2.b. On non-installed equipment:  
 
 Not applicable. 
 
 
1.F. APPROVAL 
 
Approval is limited to civil version helicopters subject to an Airworthiness Certificate. 
 
The technical information contained in Revision 0 of this ALERT SERVICE BULLETIN was approved  
on March 21, 2007 under the authority of EASA Design Organisation Approval No. 21J.056.

### Page 4

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 4/18 
2007.03.22 
 
The technical information contained in Revision 1 of this ALERT SERVICE BULLETIN was approved  
on March 22, 2007 under the authority of EASA Design Organisation Approval No. 21J.056. 
 
 
1.G. MANPOWER 
 
Qualification: 1 mechanic to perform the check and the removal / installation work. 
   2 mechanics to adjust the friction. 
 
Time for the operations: Check: Approximately 15 minutes. 
 Grease-lubrication: Approximately 3 hours for the two tangential gearboxes. 
 
 
1.H. WEIGHT AND BALANCE  
 
Not applicable. 
 
 
1.I. EFFECT ON ELECTRICAL LOADS 
 
Not applicable. 
 
 
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE 
 
Not applicable. 
 
 
1.K. REFERENCES 
 
- AS332 / AS532 helicopters except versions L2, A2 and U2 
Maintenance Manual (MET): Work Cards 76.20.00.501 - 76.20.00.601  
 
- AS332 L2 and AS532 A2 and U2 helicopters 
Aircraft Maintenance Manual (MMA): Tasks 76-20-00-211 - 76-20-00-821 
 
- SA330 helicopters 
Maintenance Manual (MDE): Work Cards 76.20.601 - 76.20.501  
 
- For all helicopters 
Standard Practices Manual (MTC): Work Cards 20.02.06.402 - 20.01.01.301  
 
 
1.L. OTHER DOCUMENTS CONCERNED 
 
EUROCOPTER will modify the following documents with respect to this ALERT SERVICE BULLETIN: 
The PRE, MET, MMA and MDE. 
These documents will be issued subsequently. 
 
 
1.M. TOOLING CONCERNED 
 
 Not applicable. 
 
 
1.N. INTERCHANGEABILITY AND MIXABILITY OF PARTS  
 
Not applicable.

### Page 5

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 5/18 
2007.03.22 
 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
 
2.A. GENERAL 
 
Refer to MTC (Standard Practices Manual) Work Card 20.02.06.402: Safetying with lockwire. 
Refer to MTC (Standard Practices Manual) Work Card 20.01.01.301: Greases. 
 
Only one procedure is described because the checks and greasing operations are the same for the 
two tangential gearboxes.  
 
 
2.B. OPERATIONAL PROCEDURE  
 
2.B.1. Checking the fuel shut-off controls. Figures 1 and 2 
 
- Remove the snap wire from the fuel shut-off controls (a). 
 
- For each fuel shut-off control (a), measure the fuel shut-off control (a) operating loads F1, F2 and F3 
 using a spring scale, in accordan ce with the following procedure: 
 
CAUTION  
 
TO MEASURE THE OPERATING LOADS F 1, F2 and F3, YOU 
MUST HOOK THE SPRING SCALE TO THE FUEL SHUT-OFF 
CONTROL (a): 
MOREOVER, DURING MEASUREMENT, THE SPRING 
SCALE PULLING DIRECTION MUST BE PERPENDICULAR 
TO THE FUEL SHUT-OFF CONTROL (a). 
 
• Pull the fuel shut-off control (a): 
 
. Disengage the fuel shut-off control (a) from detent A. 
. Measure the maximum control operating load F1 between detents A and B. 
. Move the fuel shut-off control (a) back to detent A. 
. Measure the F2 maximum load required to override detent A. 
. Measure the F3 maximum load required to override detent B. 
 
• If the F1 load value is equal to or below 3 daN, and if the F2 and F3 load values are equal to or 
below F1 + 1.5 daN, leave as is. Set the fuel shut-off controls (a) to their initial position and lock 
them with snap wire. 
• If the F1 load value is above 3 daN, or if one of the F2 or the F3 load values is above F1 + 1.5 daN, 
comply with paragraph 2.B.2. before resuming flights.

### Page 6

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 6/18 
2007.03.22 
 
 
 
2.B.2. Checking and grease-lubricating the tangential gearboxes. Figures 3 to 7. 
 
2.B.2.a. Preliminary steps  
 
- AS332 / AS532 helicopters except versions L2, A2 and U2. 
 
- Install the access equipment. 
- Open the sliding cowling and the engine cowlings.  
- Install the engine cowling walkways. 
- Open or remove: 
. panel 2 ALPHA from the electrics cabinet, 
. panel 51 ALPHA from the ceiling, 
. the soundproofing panels at the tangential gearbox and at the fuel shut-off cock. 
- Disconnect the micro-switches (b), Figure 3. 
 
- AS332 L2 and AS532 A2 and U2 helicopters 
 
- Install the access equipment. 
- Open the sliding cowling and engine cowlings. 
- Install the engine cowling walkways. 
- Open or remove: 
. the top panel from the electrics cabinet, 
. the overhead panel and the control linkage access panels. 
-  Disconnect the micro-switches (b), Figure 4. 
 
- SA330 helicopters 
 
- Remove the center soundproofing panel from between frames 3245 and 3855. 
- Open the sliding cowling, the engine cowlings and install the walkways. 
 
2.B.2.b. Procedure 
 
TO ENSURE OPTIMUM RELIABILITY, YOU MUST TAKE THE 
FOLLOWING PRECAUTIONS WHEN HANDLING THE 
FLEXIBLE CONTROLS: 
–   IT IS FORBIDDEN TO: 
 •   BEND THE SLIDING END, 
 •   USE EXCESSIVE FORCE ON THE CONTROL, 
 •  BEND THE FLEXIBLE CONTROLS. 
–   IT IS ADVISABLE TO: 
 •   COMPLY WITH THE OPERATING LOADS, 
 •   INSTALL OR COIL THE FLEXIBLE CONTROLS BY    
    ENSURING A RADIUS GREATER THAN 150 mm. 
 
- Disengage the Teleflex cables (g) from the tangential gearbox (c). Figures 3 to 6 
 
. On the lever end. 
o Unlock and uncouple clevis (m). 
o  Disengage the cable from swivel bearing retain er (p) by unscrewing it (note the number of 
turns) until it is disengaged from the tangential gearbox wheel. 
 
 
CAUTION

### Page 7

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 7/18 
2007.03.22 
 
 
. On the fuel shut-off cock end. 
o Uncouple end-fitting (n) from the fuel shut-off cock lever. 
o  Disengage the cable from swivel bearing retain er (q) by unscrewing it (note the number of 
turns) until it is disengaged from the tangential gearbox wheel. 
 
- Unlock and unscrew the end-fittings (f) 
 
- Remove the tangential gearbox (c): Figure 6  
 
. Unscrew and remove the nuts (j) and (k) and the washers (h) and (i). 
. Unscrew and remove the screws (d) and washers (e). 
 
- Open and clean the tangential gearbox (c) (with white spirit). 
 
-  Check the condition of the tangential gearbox (c):  
 
• If there is corrosion in the tangential gearbox (c): 
o Scrap the tangential gearbox (c). 
o Open the new tangential gearbox (1). 
o Lubricate the interior of the tangential gea rbox (1) with a small amount of G-354 
grease as shown on Figure 7, then close the tangential gearbox. 
 
• If there is no corrosion in the tangential gearbox (c): 
o Lubricate the interior of the tangential gearbox (c) with a small amount of G-354 
grease as shown on Figure 7, then close the tangential gearbox. 
 
- Install the tangential gearbox: Figure 6 
 
• Fit and tighten the screws (d) and washers (e). 
• Fit the washers (h) and (i), fi t and tighten the nuts (j) and (k). 
 
WHEN FITTING THE WASHERS ON THE 
TANGENTIAL GEARBOX (c), THE LATTER MUST 
BE IN THE ASSEMBLY CONFIGURATION SHOWN 
ON FIGURE 6. 
 
• Lock the screws (d) with lockwire (2). 
 
- Apply G-354 grease to the cable and the visible areas of the slide tubes. 
 
- Tighten and lock the end-fittings (f) with lockwire (2). Figure 6. 
 
- Engage the Teleflex cables. Figures 3 to 5. 
 
 
• On the lever end. 
o Engage the cable until it comes into cont act with the tangential gearbox wheel. 
o Screw the cable in accordance with the number of turns previously noted down.  
o  Couple the clevis (m) to the fuel shut-off leve r.  Safety the clevis (m) with a cotter pin. 
 
 
 
 
CAUTION

### Page 8

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 8/18 
2007.03.22 
 
 
 
• On the fuel shut-off cock end. 
o Engage the cable until it comes into cont act with the tangential gearbox wheel. 
o Screw the cable in accordance with th e number of turns previously noted.  
o  Couple the end-fitting (n) to the fuel shut-off cock lever and check that the end-fitting is 
locked. 
 
NOTE 
 
After installation, the cables must not protrude from the guide 
tubes when the levers are in th e forward position. The insertion 
depth of the cables in the guide tubes must be less than 10 mm 
(.394 in). 
 
 
- Actuate the fuel shut-off controls (a). The controls must be free to slide in each sheath. 
 
2.B.2.c. Adjustment and check 
 
- Adjust the tangential gearbox (c) friction as pe r (MET) Work Card 76.20.00.601 or (MMA) Sub-Task 
76-20-00-211-004 of Task 76-20-00-211. 
  
- Check: 
• the fuel shut-off control (a) travel as per (MET ) Work Card 76.20.00.601 or (MMA) Task 76-20-00-
211 or (MDE) Work Card 76.20.601. 
• the ventilation flaps (l) as per (MET) Work Ca rd 76.20.00.601 or (MMA) Sub-Task 76-20-00-211 -
001 of Task 76-20-00-601. 
 
- If necessary, adjust the fuel shut-off controls (a) as per (MET) Work Card 76.20.00.501 or 
 (MMA) 76-20-00-821 or (MDE) 76.20.501 
 
2.B.2.d. Final steps 
 
- AS332 / AS532 helicopters except versions L2, A2 and U2. 
 
• Set the fuel shut-off levers (a) to their initial position: 
. lock the fuel shut-off controls (a) with snap wire, 
. connect the micro-switches (b), Figure 3.  
. Replace the plastic rivets (3) as necessary.  
• Install and close: 
. panels 2ALPHA and 51ALPHA, 
. the soundproofing panels at the tangential gearbox and the fuel shut-off cock. 
• Close the engine cowlings and the sliding cowling. 
• Remove the engine cowling walkways. 
• Remove the access equipment. 
 
- AS332 L2 and AS532 A2 and U2 helicopters 
 
• Set the fuel shut-off levers (a) to their initial position: 
. lock the fuel shut-off controls (a) with snap wire, 
. connect the micro-switches (b), Figure 4, 
. replace the plastic rivets (3) as necessary. 
• In the cabin, install or close: 
  - the control linkage access panels and the overhead panel, 
  - the top panel of the electrics cabinet.

### Page 9

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 9/18 
2007.03.22 
   
 
 
• Close the engine cowlings and the sliding cowling. 
• Remove the engine cowling walkways. 
• Remove the access equipment. 
  
- SA330 helicopters 
 
• Set the fuel shut-off controls (a) to their initial position. 
• Lock the fuel shut-off controls (a) with snap wire. 
•  Install the center soundproofing panel between frames 3245 and 3855. 
• Close the sliding cowling and the engine cowlings. 
• Remove the walkways. 
 
 
2.C. IDENTIFICATION 
 
Record compliance with this ALERT SERVICE BULLETIN in the helicopter documents. 
 
 
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS 
  
           Not applicable.

### Page 10

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 10/18 
2007.03.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 1 – Location of the fuel shut-off controls 
 
a

### Page 11

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 11/18 
2007.03.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
  
  
 
  
 
 
 
  
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2 – Checking the fuel shut-off control
a 
F2 
F1
F3 
A
B

### Page 12 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000380
B
Figure 3 - Fuel shut-off control (C, C1, L, L1, B, B1, F1, M, M1, AC, AL, SC, UC, UE and UL)
Approved under EASA DOA No. 21J.056  Page 12/18
2007.03.22

### Page 13 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000380
m
a
Figure 4 - Fuel shut-off control (L2, A2 and U2)
Approved under EASA DOA No. 21J.056  Page 13/18
2007.03.22

### Page 14

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 14/18 
2007.03.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 5 – Fuel shut-off control (SA330) 
a 
c
1
g 
m 
n
p 
q

### Page 15

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 15/18 
2007.03.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 6 – Tangential gearbox Removal / Installation  
c
1 
d
e 
i h 
j 
k 
f 2

### Page 16

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 16/18 
2007.03.22 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 7 – Lubricating the tangential gearbox with grease 
Tangential gearbox 
areas to be lubricated 
with grease

### Page 17

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 17/18 
2007.03.22 
 
 
 
 
3. MATERIAL INFORMATION  
 
3.A. MATERIAL: COST – AVAILABILITY 
 
For any information concerning kits and / or components, contact the Sales and Customer Relations 
Department of the EUROCOPTER Network. 
 
 
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT  
 
Not applicable. 
 
 
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER / ENGINE / COMPONENT 
 
3.C.1. Kit(s) or component(s) to be ordered for one helicopter or one assembly 
 
Material Part Number Qty Item Key Word Former Part Number Instructions 
      
332A57231000 AR 1 Tangential gearbox  As necessary 
23310CA015015 2  Cotter pin   
      
 
3.C.2. Items to be ordered separately 
 
 Material Part Number Qty Item Key Word 
     
 AIR4210/B or G-354 AR  Grease 
 EN3628-0,8 AR 2 Lockwire, 0.8 diameter 
 23321 AR  Snap wire, annealed copper,  
0.3 diameter 
 CARECLEAN-AS1 AR  White-Spirit 
 52607NOIR 2 3 Plastic rivet 
 
The products required for compliance with the Tasks and / or Work Cards listed in paragraph 1.K., can 
be ordered from the INTERTURBINE company. 
Website: http://www.itlogistics.de 
Telephone: +49.41.91.809.300 
AOG: +49.41.91.809.444

### Page 18

T.F.S. No. 00000380 
Approved under EASA DOA No. 21J.056       Page 18/18 
2007.03.22 
 
 
 
3.D. PROCUREMENT CONDITIONS  
 
Order the required quantity (unless otherwise specified) 
 
from 
 
EUROCOPTER 
Etablissement de Marignane 
Sales and Customer Relations Department 
ECR 
13725 MARIGNANE CEDEX 
FRANCE 
NOTE 1 
 
For ALERT SERVICE BULLETINS, order by: 
Telex: HELICOP 410 969F 
Fax: +33 (0)4 42 85 99 96 
 
 
NOTE 2 
 
On the purchase order, please specify the mode of 
transport, the destination and the serial numbers of the 
helicopters to be modified. 
 
 
 
4. APPENDIX 
  
 Not applicable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
