# Eurocopter Service Bulletin 65-006

Copy: Revision 1 ("Eurocopter SB EC155 65-006 R1"), 16 pages: PDF https://openairdocs.org/files/sha256/1f/fe/1ffe70cf5d8818da65e173e5caac041167018bbfa9b4e7e1679343fefd03cf97; text https://openairdocs.org/service-documents/airbus-helicopters/sb-65-006/file/1ffe70cf5d88.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1123, the docket of AD 2021-05-05. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Service Bulletin)
- Number: 65-006
- Latest revision known: 65-006, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus-helicopters/sb-65-006

## Text (16 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1123, the docket of AD 2021-05-05. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

EUROCOPTER
B, B1CIVIL VERSIONS:
DIRECTION TECHNIQUE SUPPORT
13725 MARIGNANE CEDEX FRANCE
SERVICE BULLETIN
No. 65-006
ROTORSSUBJECT:
TGB control shaft guide bush replacement
Corresponds to MOD 0765B58
DATE OF ISSUEDATE OF APPROVALREVISION No.
2010.04.28
2011.03.21
On: April 01, 2010
On: February 23, 2011
Revision 0
Revision 1
Page 1/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21This document is available on the Internet: www.eurocopter.com/techpub
SERVICE BULLETIN EC155

### Page 2

1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment
EC 155 type helicopters with TGB pre-MOD 0765B58.
Helicopters post-MOD 0765B56 on TGB are not affected by this Service Bulletin.
1.A.2. Non-installed equipment
- TGB P/N 365A33-6005-XX, equipped with:
Guide bush P/N 365A33-6188-20..
. Guide bush P/N 365A33-6189-20 or 365A33-6189-21.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
The purpose of this Service Bulletin Revision 0 was to improve control of the functional play between control
shaft and TGB wheel in order to limit the friction loads on the control bearing.
The purpose of this Service Bulletin Revision 1 is to:
- add a figure showing seals positioning (Figure 4),
- modify the seals quantity reference AS3209-011 (addition of a seal).
Revision 1 of this Service Bulletin does not question compliance with Revision 0.
1.D. DESCRIPTION
During landing, a pilot felt a loss of tail rotor control efficiency.
Further to this incident, EUROCOPTER published Alert Service Bulletin 05A015 (AD 2009-0247) and designed
various modifications, notably 0765B58.
This modification consists of replacing both guide bushes (which ensure translation guidance of the TGB control
shaft) by 2 TORLON guide bushes.This new material provides a better control of the thermal expansion coefficient.
The bush dimensions remain unchanged.
Therefore, EUROCOPTER recommends compliance with this Service Bulletin.
1.E. COMPLIANCE
1.E.1. Compliance at the works
1.E.1.a. On helicopters
Not applicable.
Page 2/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 3

1.E.1.b. On non-installed equipment
Not applicable.
1.E.2. Compliance in service
1.E.2.a. On Helicopters/installed equipment
- EUROCOPTER recommends compliance with this Service Bulletin.
- The works must be performed by the Operator on installed equipment. Comply with Paragraph 2.B. of this
Service Bulletin within 600 flying hours or at the latest within one year as from the date of issue of this
Service Bulletin.
1.E.2.b. On non-installed equipment
- The works must be performed by the Operator on non-installed equipment.
- Modify stocks of TGBs as per Paragraph 2.B, before installation on helicopter or within one year maximum
as from the date of issue of this Service Bulletin.
1.F. APPROVAL
1.F.1. Approval of modifications
The information or instructions relating to modification 0765B58 were approved on November 16, 2009 for
helicopters of civil versions subject to an Airworthiness Certificate.
1.F.2. Approval of the Service Bulletin
The technical information contained in this Service Bulletin Revision 0 was approved on April 01, 2010 under
the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an
Airworthiness Certificate.
The technical information contained in this Service Bulletin Revision 1 was approved on February 23, 2011
under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject
to an Airworthiness Certificate.
1.G. MANPOWER
1.G.1.Qualification
For compliance with this Service Bulletin Eurocopter recommends the following personnel qualifications:
Qualification: 1 Mechanical Technician.
1.G.2.Time for the operations
Time for the operations is indicated for reference, for a standard configuration.
Time for the operations: 4 hours approximately.
Page 3/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 4

1.G.3.Estimated helicopter grounding time
1.5 day.
1.H. WEIGHT AND BALANCE
1.H.1. Weight
Not applicable.
1.H.2. Moment
Not applicable.
1.I. EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD
Not applicable.
1.K. REFERENCES
GENERAL - General Safety Instructions - Hydraulic power.AMM : 29-00-00-911 :
ROTOR HEAD - Removal/Installation - Tail rotor head.AMM : 64-20-00-061 :
ROTOR HEAD - Removal/Installation - TRH fairing.AMM : 64-20-01-061 :
GEARBOX - Removal/Installation - Tail rotor control shaft assembly.AMM : 65-20-01-066 :
GEARBOX - Filling and draining the TGB.AMM : 65-20-01-611 :
ROTOR FLIGHT CONTROL - Inspection - Flight controls after maintenance work.AMM : 67-00-00-211 :
ROTOR FLIGHT CONTROL - General safety instructions - Flight controls.AMM : 67-00-00-911 :
SERVOCONTROL - Removal/Installation - Tail servocontrol.AMM : 67-30-02-061 :
SEALING COMPOUNDS USED IN STRUCTURAL REPAIRS OR ON TRANSMISSION
ASSEMBLIES - Sealing compound PR 1436GS NA (for spray application).
MTC : 20.05.01.221 :
SAFETYING AND LOCKING ASSEMBLIES - Safetying with lockwire.MTC : 20.02.06.402 :
SAFETYING AND LOCKING ASSEMBLIES - Safetying with lockplates.MTC : 20.02.06.403 :
TECHNICAL INSTRUCTIONS - Instructions applicable when working on an aircraft electrical
circuit or when energizing aircraft power generating systems on ground.
MTC : 20.07.03.406 :
TECHNICAL INSTRUCTIONS - General principles applicable for visual cleanliness,
appearance checks on an aircraft after an inspection or repair.
MTC : 20.07.03.408 :
1.L. OTHER DOCUMENTS AFFECTED
1.L.1. Documents already updated
Not applicable.
Page 4/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 5

1.L.2. Documents to be updated
Illustrated Parts Catalog (IPC): Chapters 65-20-10 and 65-20-11.
1.M. TOOLING AFFECTED
Not applicable.
1.N. INTERCHANGEABILITY OR MIXABILITY OF PARTS
1.N.1. Interchangeability
New guide bushes P/N 365A33-6222-20 and 365A33-6223-20 are physically interchangeable with former guide
bushes P/N 365A33-6188-20, 365A33-6189-20 and 365A33-6189-21.
1.N.2. Mixability
Mixing between new guide bushes P/N (365A33-6222-20, 365A33-6223-20) (black color) and former guide
bushes (P/N 365A33-6188-20, 365A33-6189-20 and 365A33-6189-21) (white color) is prohibited.
Page 5/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 6

2. ACCOMPLISHMENT INSTRUCTIONS
2.A. GENERAL
2.A.1. General instructions
- Apply sealant as per MTC Work Card 20.05.01.221.
- Carry out safetying with lockwire as per MTC Work Card 20.02.06.402.
- Carry out safetying with lockplates as per MTC Work Card 20.02.06.403.
2.A.2. Special safety instructions
- Refer to general principles applicable for visual cleanliness, appearance checks on an aircraft after an inspection
or repair as per MTC Work Card 20.07.03.408.
2.A.3. Document checks
Not applicable.
2.B. OPERATIONAL PROCEDURE
2.B.1. Preliminary steps
- Install suitable access means.
- Disconnect all electrical power supplies as per MTC Work Card 20.07.03.406.
2.B.2. Procedure
NOTE 1
The control rod assembly guide bush replacement
procedure is performed without removing the TGB.
2.B.2.a. Removing TGB control rod/shaft assembly
CAUTION
BEFORE ANY INTERVENTION ON TRH ASSEMBLY,
LOCK THE TRANSMISSION WITH THE ROTOR BRAKE.
- Remove tail servocontrol as per AMM Task 67-30-02-061.
- Drain TGB as per AMM Task 65-20-01-611.
As per Figure 1:
- Remove TRH fairing (q) after loosening bolts (r) (DETAIL A).
NOTE 2
Bolts (r) must mandatorily be loosened at least 2 mm to
allow fairing removal.
- Mark position of central plate (s) with respect to control spider (t) by a reference line.
- Unsafety nut (x), tabwasher (z).
Page 6/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 7

- Position tooling (W) on nut (x) and lock control rod (b) with spanner secured on hexagon at shaft end.
- Loosen and remove nut (x), retain it.
- Remove and scrap lockwasher (z).
- Retain washer (aa).
- Unsafety and remove attachment bolts (u) from central plate (s) on control spider (t) and washers (v), retain
them.
- Position tooling (Y) and screw in M8 bolts of tooling (Y) and by means of a mallet, gently tap at tooling center
(Y) to release control shaft (b).
- Loosen and remove M8 bolts and place them on tooling (Y).
- Remove central plate (s).
NOTE 3
In case of replacement of central plate (s), check
interchangeability dimension as per AMM Task .
As per Figures 2 and 4 :
- Remove sealing bead from around cover (e) as well as from nuts (f) by means of Plexiglass scraper.
- Remove nuts (f) and washers (g).
- Remove 3 plastic plugs from cover (e).
- Remove cover (e) by means of 3 M6 bolts of suitable length (greater than cover thickness).
- Replace seals (h) and (j) from casing (ad) as required..
- Remove control rod/shaft assembly (b,c).
- Replace seals (k) and (m).
2.B.2.b.Replacing guide bushes
As per Figures 2 and 3:
- On control rod (b), remove guide bush (n) and scrap it.
- As replacement for guide bush (n) install guide bush (1).
- Inside TGB on control spider side, by means of a locally-manufactured tool (spatula of type ICO
97.42.00.01.030), remove guide bush (p) and scrap it.
NOTE 4
Take care not to damage guide bush fitting groove.
- As replacement for guide bush (p) install guide bush (2).
2.B.2.c. Installing TGB control rod/shaft assembly
NOTE 5
If seals (h, j, k or m) were damaged (tear, cut, crushing,
etc.), replace them by new seals (3, 4, 5, 6). (See AMM
Task 65-20-01-066.
As per Figures 1 to 3
- Thoroughly lubricate bearing with TGB oil:
Hold control rod/shaft assembly upright, rod (b) up..
. Pour oil through hole (a) and turn control rod (b) (Figure 3 DETAILS B and C) .
- Wipe control rod/shaft assembly and guide bush  (1).
- Fit seal (k) or (5) on control shaft (b) (Figure 2 DETAIL A).
Page 7/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 8

- Fit seal (m) or (6) in its recess.
- Install control rod/shaft assembly (b, c) in TGB.
- Relocate central plate (s) with respect to control spider (t) by reference to line made during removal (paint,
felt tip pen, etc.).
- Lubricate (with TGB oil) bolts (u), washers (v) (washer chamfers on bolt head side).
- Fit washers (v) and bolts (u) on control spider (t).
- Tighten bolts (u) to torque prescribed as per AMM Task 64-20-00-061.
- Safety bolts (u) by two's with lockwire  (10).
- Fit O-rings (h) or (4) and (j) or (3) in their respective grooves on casing (ad).
- Fit cover (e).
- Fit washers (g) and nuts (f).
- Tighten nuts (f) to torque prescribed as per AMM Task 65-20-01-066.
- Produce sealing bead (11) around cover (e) and on nuts (f).
As per Figure 1
- Fit spigot washer (aa).
- Fit tabwasher  (8).
- Fit nut (x) on control rod (b).
- Position tooling (W) on nut (x).
- Lock control shaft (b) with spanner secured on hexagon at shaft end and tighten to torque prescribed as
per AMM Task 64-20-00-061 with tooling (W).
NOTE 6
As required, adjust position of nut (x) to prevent any lug or
tab of lockwasher (8) from facing a nut corner, while
maintaining specified tightening torque tolerance.
- Remove tooling (W).
- Safety by bending tabs of tabwasher  (8) on nut (x).
- Degrease, on hub body (ab), anchorage groove of TRH fairing retaining springs (q) by means of cloth soaked
with solvent (white spirit) (12).
- Install TRH fairing (q) aligning red paint marks, bolts (r) and tighten to torque prescribed as per AMM Task
64-20-01-061.
- Fill TGB with oil and top up to max. level as per AMM Task 65-20-01-611.
- Install tail servocontrol as per AMM Task 67-30-02-061.
- Release rotor brake.
2.B.3. Tests
- Reconnect all electrical power supplies as per MTC Work Card 20.07.03.406.
- Carry out operating test as per AMM Task 67-00-00-211.
- Actuate yaw pedals and check free travel of yaw control.
- Shut down electrical power supply.
2.B.4. Final steps
- Remove the access means.
2.B.5. Ground run/flight test
Carry out a ground run-up of at least 5 minutes and check for any oil seepage at TGB.
Page 8/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 9

Carry out checks after operations on flying controls as per Task No. 5 (hydraulic tests) of section 8.3 - Flight
Manual (PMV).
2.C. OPERATIONAL PROCEDURE ON NON-INSTALLED EQUIPMENT
2.C.1. Stock retrofitting
- TGB stock retrofitting is recommended.
- Retrofit TGB as per Paragraph 2.B, before installation on helicopter or within one year maximum as from the
date mentioned in page footer.
2.C.2. Stock replacement, stock scrapping and stock building-up
Stock replacement and new stock building-up are incumbent on Operator.
2.D. IDENTIFICATION
2.D.1. Identification of modifications in the documentation
- Record embodiment of Modification 0765B58 and compliance with this Service Bulletin 65.00.17 Revision 1
in the aircraft documents.
- Record embodiment of Modification 0765B58 on equipment log card (FM) for TGB.
2.D.2. Identification of modifications on equipment
Not applicable.
2.D.3. Identification of the new version
Not applicable.
2.E. OPERATING AND MAINTENANCE INSTRUCTIONS
2.E.1. Operating instructions
Not applicable.
2.E.2. Scheduled maintenance instructions
Not applicable.
2.E.3. Unscheduled maintenance instructions
Not applicable.
Page 9/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 10 (OCR)

Z EUROCOPTER  AN EADS COMPANY
SERVICE BULLETIN EC155
ab-
a a
Z -8
×<W
Figure 1
Approved under EASA DOA No. 21J.056.  65-006  Page 10/16
2011.03.21

### Page 11 (OCR)

EUROCOPTER
AN EADS COMPANY
SERVICE BULLETIN EC155
e
2
m
6
Figure 2
Approved under EASA DOA No. 21J.056.  65-006  Page 11/16
2011.03.21

### Page 12 (OCR)

→ EUROCOPTER  AN EADS COMPANY
SERVICE BULLETIN EC155
в-СД
Figure 3
Approved under EASA DOA No. 21J.056.  65-006  Page 12/16
2011.03.21

### Page 13 (OCR)

EUROCOPTER
AN EADS COMPANY
SERVICE BULLETIN EC155
ad
Ґ
FWD
→
FWD
SECTION E-E  SECTION D-D
ad
ad
Figure 4
Approved under EASA DOA No. 21J.056.  65-006  Page 13/16
2011.03.21

### Page 14

3. MATERIAL INFORMATION
3.A. MATERIAL: PRICE AND AVAILABILITY
3.A.1. Cost
3.A.1.a. Components
Under any user order notified before 31 December 2012, the kits and/or the components shall be delivered
free of charge.
3.A.1.b. Tools
Not applicable.
3.A.2. Availability
3.A.2.a. Components
Delivery deadlines will be indicated by Customer Support Sales Department on Operator's request.
3.A.2.b. Tools
Not applicable.
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT
Not applicable.
3.C. MATERIAL REQUIRED FOR EACH HELICOPTER/ENGINE /COMPONENT
3.C.1. Kits or components to be ordered for one helicopter or one assembly
For embodiment of Modification 0765B58, place order for kit 365A07-65B5-8071 and equipment spares to be
ordered separately.
InstructionsFormer P/NKey WordItemQtyMaterial P/N
TGB control shaft guide bush replacement kit  including:1365A07-65B5-8071
scrap365A33-6189-20 and
365A33-6189-21
Guide bush(1 )1365A33-6223-20
scrap365A33-6188-20Guide bush(2)1365A33-6222-20
3.C.2. Material to be ordered separately
Key WordItemQtyMaterial P/N
Page 14/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 15

Key WordItemQtyMaterial P/N
O-ring(3)1AS3209-253
O-ring(4)2AS3209-011
Seal(5)1JF4-11DF901
Seal(6)1JF4-19ADF901
Tabwasher(8)123351CA160
Lockwire(10)2 mEN3628-0.8
3.C.3. Material to be modified at the Manufacturer's or to be returned
Not applicable.
3.C.4. Products to be ordered separately
Key WordItemQtyMaterial P/N
Sealant(11 )100 grECS2068.10
Solvent (white spirit)(12)1 lWHITESPIRITBIDON5L
3.C.5. Tools
As per Work Cards and Tasks referenced in this Service Bulletin and list below:
Key WordItemQtyMaterial P/N orequivalent
TRH nut spanner(W)1365A93-3362-20
Control spider extractor.(Y)1365A93-3363-00
3.C.6. Material supplied by the User
Not applicable.
3.C.7. Material required for non-installed components
Not applicable.
3.D. PROCUREMENT CONDITIONS
Order the required quantity from the EUROCOPTER network's Customer Support Sales Department.
EUROCOPTER
Etablissement de Marignane
Direction Ventes et Relations Client (ECR)
13725 MARIGNANE CEDEX
FRANCE
Page 15/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

### Page 16

4. APPENDIX
Not applicable.
Page 16/1665-006Approved under EASA DOA No. 21J.056.
2011.03.21
SERVICE BULLETIN EC155

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
