# Eurocopter Emergency Alert Service Bulletin 67.18

Copy: No revision named ("U.S. DOT/FAA - Eurocopter EASB 67.18"), 14 pages: PDF https://openairdocs.org/files/sha256/12/52/12526d89377db362f2b5ecd241299fcce87ffb53f4adcc383470716de4c2b464; text https://openairdocs.org/service-documents/airbus-helicopters/sb-67-18/file/12526d89377d.md. Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-0891; AD 2011-03-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus Helicopters](https://openairdocs.org/service-documents/airbus-helicopters.md) (issued as Eurocopter)
- Type: Service bulletin (Emergency Alert Service Bulletin)
- Number: 67.18
- Page: https://openairdocs.org/service-documents/airbus-helicopters/sb-67-18

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-03-02](https://openairdocs.org/ad/2011-03-02.md), effective Apr 14, 2011: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus-helicopters/sb-67-18/proposed.md).

## Text (14 pages)

Rights: © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-0891; AD 2011-03-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 1/14 
2009.08.03 
This document is available on the Internet:  www.eurocopter.com/techpub 
 
EUROCOPTER  
DIRECTION TECHNIQUE SUPPORT 
13725 MARIGNANE  CEDEX FRANCE 
 
EMERGENCY 
ALERT SERVICE BULLETIN 
 
PUMA NUMBER VERSIONS 
Civil: F,G,J 
SA330 67.18 Military: B,Ba,C,Ca,Ea,H,L,S1, Jm,Sm 
 
 
 
 
SUBJECT: ROTOR FLIGHT CONTROLS 
 
Inspection and reconditioning of pilot and copilot pedal unit 
adjustment system 
 
 
Corresponds to MOD: 330A779820.00 
 
REVISION No. DATE OF APPROVAL DATE OF ISSUE 
   
   
Revision 0 On: July 31, 2009 2009.08.03

### Page 2

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 2/14 
2009.08.03 
 
 
1. PLANNING INFORMATION 
 
1.A. EFFECTIVITY 
 
1.A.1. Helicopters/installed equipment 
 
All SA330 helicopters that have embodied MOD 07.10.304 (pedal position adjustment system) but 
have not embodied MOD 330A779820.00. 
 
NOTE 
 
Refer to the Individual Inspection Record (RIC AMS), 
the Equipment Log Cards (FMs) or the aircraft 
logbook to identify the actual configuration of the 
helicopter. 
 
 
1.A.2. Non-installed equipment 
 
On all pedal units that have embodied MOD 07.10.304 (pedal position adjustment system) but have 
not embodied MOD 330A779820.00. 
 
 
1.B. ASSOCIATED REQUIREMENTS 
 
Not applicable. 
 
 
1.C. REASON 
 
To prevent the risk of losing the yaw control provided by the pilot and copilot pedal unit. 
 
This ALERT SERVICE BULLETIN will be the subject of an EASA Airworthiness Directive. 
 
 
1.D. DESCRIPTION 
 
While adjusting the position of the pedal unit on a SA330 helicopter, the copilot set the position 
beyond the end limit ("tall pilot" position). This led to the separation of the pedal adjustment system 
and the pedals rocking forward. 
 
It was determined after investigation that the Loctite bond on the "tall pilot" stop nut was damaged, 
most likely due to aging of the adhesive. The nut came loose and could no longer perform its stop 
function. The threaded rod of the adjustment system separated from the system.  
 
The separation of the adjustment system could result in the loss of control of the pedal units, causing 
the helicopter to begin rotating. 
 
EUROCOPTER has defined an inspection procedure to determine the effectiveness of the "tall pilot" 
stop. The safetying on the stop nut must also be reworked on customer premises.

### Page 3

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 3/14 
2009.08.03 
 
 
1.E. COMPLIANCE 
 
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory. 
 
1.E.1. Compliance at the works 
 
1.E.1.a. On helicopters/installed equipment 
 
Not applicable. 
 
1.E.1.b. On non-installed equipment 
 
Comply with paragraphs 2.B.2., 2.B.3. and 2.B.5. prior to delivery. 
 
1.E.2. Compliance in service: By the operator 
 
1.E.2.a. On helicopters/installed equipment 
 
Perform the inspection defined in paragraph 2.B.1. within 10 flight hours at the latest following 
receipt of this ALERT SERVICE BULLETIN issued on the date indicated at the foot of the page. 
 
Result Analysis: 
 
- If a non-conformity is found in paragraph 2.B.1., comply with paragraphs 2.B.2., 2.B.3. or 2.B.4. 
and 2.B.5. before resuming flights. 
 
- If no non-conformity is found in paragraph 2.B.1., comply with paragraphs 2.B.2., 2.B.3. and 2.B.5. 
within 3 months at the latest following receipt of this ALERT SERVICE BULLETIN issued on the 
date indicated at the foot of the page. 
 
When complying with paragraph 2.B.3. or 2.B.4., it is temporarily permitted not to install the 
half-bushings. Consequently, flights without the half-bushings can be resumed for one year 
from the date of issue of this ALERT SERVICE BULLETIN. 
 
1.E.2.b. On non-installed equipment 
 
Comply with paragraphs 2.B.2., 2.B.3. and 2.B.5. prior to installation on helicopter and at the 
latest within 3 months following receipt of this ALERT SERVICE BULLETIN issued on the date 
indicated at the foot of the page. 
 
 
1.F. APPROVAL 
 
1.F.1. Approval of the modifications 
 
The information or instructions relate to MOD 330A779820.00 approved on July 30, 2009 by the EASA 
for civil version helicopters subject to an airworthiness certificate.

### Page 4

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 4/14 
2009.08.03 
 
 
 
1.F.2. Approval of the ALERT SERVICE BULLETIN 
 
The technical information contained in Revision 0 of this ALERT SERVICE BULLETIN was approved 
on July 31, 2009 under the authority of EASA Design Organization Approval No. 21J.056 for civil 
version helicopters subject to an airworthiness certificate. 
 
The technical information contained in Revision 0 of this ALERT SERVICE BULLETIN was approved 
on July 31, 2009 by the EUROCOPTER Airworthiness Department for military version helicopters. 
 
 
1.G. MANPOWER 
 
1.G.1. Qualification 
 
1 mechanic. 
 
1.G.2. Time for the operations 
 
3 hours. 
 
1.G.3. Estimated helicopter grounding time 
 
3 hours. 
 
 
1.H. WEIGHT AND BALANCE 
 
Not applicable. 
 
 
1.I. EFFECT ON ELECTRICAL LOADS 
 
Not applicable. 
 
 
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE 
 
Not applicable. 
 
 
1.K. REFERENCES 
 
Standard Practices Manual (MTC): 
Work Card: 20.02.05.404 
Work Card: 20.02.06.406 
Work Card: 20.02.06.409

### Page 5

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 5/14 
2009.08.03 
 
 
 
1.L. OTHER DOCUMENTS AFFECTED 
 
Not applicable. 
 
 
1.M. TOOLING AFFECTED 
 
Not applicable. 
 
 
1.N. INTERCHANGEABILITY OR MIXABILITY OF PARTS 
 
Not applicable.

### Page 6

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 6/14 
2009.08.03 
 
 
 
2. ACCOMPLISHMENT INSTRUCTIONS 
 
2.A. GENERAL 
 
Not applicable. 
 
 
2.B. OPERATIONAL PROCEDURE 
 
NOTE 1 
 
The procedure is to be followed on both the pilot and 
copilot sides. 
 
2.B.1. Functional test of pedal unit adjustment system (Figure 1) 
 
2.B.1.a. Check for presence of "tall pilot" stop function 
 
- Turn grip (o) to slowly bring the pedal unit to "tall pilot" limit stop. 
- Check that the "tall pilot" limit stop functions correctly.  
- Check that the fixed sleeve (j) ha s not separated from the cap (k). 
- Check that the half-bushings (s) are in place. 
- Check that the sliding sleeve (i) can freely mo ve forward approximately 2 mm with the pedal unit 
at the "tall pilot" limit stop (see Figure 1 - DETAIL A). 
 
NOTE 2 
 
If the half-bushings (s) are not present, do not check the 
movement on the sliding sleeve (i). 
 
2.B.1.b. Result Analysis 
 
- If the following is detected:  
 . absence of "tall pilot" limit stop, 
   or 
 . separation of fixed sleeve (j) and cap (k), 
   or 
 . no freedom of movement on sliding sleeve (i) with the half-bushings (s) in place, 
Comply with paragraphs 2.B.2., 2.B.4. and 2.B.5. 
 
- If only the following is detected:  
 . absence of the half-bushings (s) 
 Comply with paragraphs 2.B.2., 2.B.3. and 2.B.5. 
 
When complying with paragraph 2.B.3. or 2.B.4., it is temporarily permitted not to install 
the half-bushings. Consequently, flights without the half-bushings can be resumed for 
one year from the date of issue of this ALERT SERVICE BULLETIN.

### Page 7

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 7/14 
2009.08.03 
 
 
 
2.B.2. Removal of pedal unit adjustment system (Figure 2) 
 
WHEN REMOVING THE ADJUSTMENT SYSTEM, 
BLOCK THE PEDALS TO AVOID DAMAGING ANY 
SURROUNDING ELEMENTS. 
 
- Remove and discard the taper pin (a). 
- Loosen and remove the nut (b), washer (c) and threaded pin (d). 
- Remove and discard the 2 taper pins (f). 
- Loosen and remove the 2 screws (g) and 2 washers (h). 
- Remove the entire pedal unit adjus tment system and place on workbench. 
 
2.B.3. Upgrade of safetying on pedal unit adjustment system (Figures 2, 3 and 4) 
 
- Remove and discard the cotter pin (n). 
- Remove the grip (o). 
- Remove and discard the cotter pin (q). 
- Move the threaded rod (r) to bring the stop nut (p ) towards the "small pilot" position in order to 
gain access to the stop nut (p) in the nut tube (m). 
- Check that at least one thread of  the stop nut (p) protrudes as indicated on Figure 3 - DETAIL 
B or Figure 4 - DETAIL C. 
. If less then one thread is visible: 
.. Perform rework of safetying as per paragraph 2.B.4. 
.  If at least one thread is visible: 
.. Use a punch to make 3 marks (x) on the end of the threaded rod (r) to provide additional 
safetying for the nut as per Figure 4 and MTC Work Card 20.02.06.406 (do not perform 
sampling tests for improper safetying). 
- If the half-bushings are found to be missing, install new half-bushings (4) inside the sliding 
sleeve (i) and bond them with epoxy adhesive (12). 
- Install cotter pin (3a) to the nut tube (m). 
- Install grip (o) and cotter pin (3b). 
 
NOTE 3 
 
The two cotter pins (3a) and (3b) must be flush and 
peened on installation. 
 
CAUTION

### Page 8

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 8/14 
2009.08.03 
 
 
 
2.B.4. Rework of safetying on pedal unit adjustment system (Figures 2, 3 and 4) 
 
- Remove and discard the taper pin (n) if  it was not removed in paragraph 2.B.3. 
- Remove the grip (o) if it was not removed in paragraph 2.B.3. 
- Remove and discard the taper pin (q) if  it was not removed in paragraph 2.B.3. 
- Heat the assembly to 120°C in order to disassemble the components bonded with Loctite 
(MTC Work Card 20.02.06.409). 
- If half-bushings (s) are present, unbond and remove the half-bushings (s) as needed following 
the instructions in MTC Work Card 20.02.06.409. 
 
NOTE 4 
 
The half-bushings are bonded with epoxy adhesive 
and may be damaged when removed. If so, they must 
be discarded. 
 
- Unbond the fixed sleeve (j) from the cap (k). 
- Remove the fixed sleeve (j) and the sliding sleeve (i). 
- Loosen and remove the cap (k) from the nut tube (m).  
- Remove the retention sleeve (l). 
- Move the threaded rod (r) to bring the stop nut (p ) towards the "small pilot" position so that the 
nut protrudes from the nut tube (m) in order to gain access to the nut. 
- Loosen, remove, clean and set aside the stop nut (p) for later use. 
 
NOTE 5 
 
Prior to installation, check the condition of each 
element removed previously. 
 
- Degrease only the section of the thread ed rod (r) that receives the stop nut (p). 
- Perform safetying on stop nut (p) by applying Lo ctite (10) as per MTC Work Card 20.02.06.409 
and torque tighten nut as indicated in MTC Work Card 20.02.05.404. 
- Use a punch to make 3 marks (x) on the end of the threaded rod (r) to provide additional 
safetying for the nut as per Figure 3 - DETAIL B or Figure 4 - DETAIL C and MTC Work 
Card 20.02.06.406 (do not perform sampling tests for improper safetying). 
- Wait for Loctite to cure (10) as per MTC Work Card 20.02.06.409. 
- Lubricate threaded rod (r) with grease (11). 
- Move the threaded rod (r) to bring the stop nut  (p) to mid-travel position (see Figure 3 – 
DETAIL B). 
- Install the retention sleeve (l).  
- Tighten the cap (k) on the nut tube (m). 
- Install the sliding sleeve (i) t ogether with the fixed sleeve (j). 
- Bond the fixed sleeve (j) and the cap (k) with epoxy adhesive (12). 
- Install the half-bushings (4) inside the slid ing sleeve (i) and bond them with epoxy adhesive 
(12). 
- Install cotter pin (3a) to the nut tube (m). 
- Install grip (o) and cotter pin (3b). 
 
NOTE 6 
 
The two cotter pins (3a) and (3b) must be flush and 
peened on installation.

### Page 9

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 9/14 
2009.08.03 
 
 
 
2.B.5. Installation of pedal unit adjustment system (Figure 2) 
 
- Offer up the pedal unit adjustment system assembly. 
- Install the 2 washers (h) and tighten the 2 screws (g) on the retention sleeve (l). 
- Install the 2 pins (2). 
- Install the threaded pin (d) and wash er (c) and tighten the nut (b).  
- Install pin (1). 
- Use the grip (o) to return the pedal unit to the mid-position. 
 
 
2.C. IDENTIFICATION 
 
- Record compliance with this ALERT SERVICE BULLETIN in the aircraft documentation on final 
completion of the operational procedure, i. e. after having checked that the half-bushings (s) or (4) 
are present or have been installed. 
- Indelibly mark the MOD number on the nut tube (m) as shown on Figure 4. 
 
 
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS 
 
Not applicable.

### Page 10 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000528
P
SECTION A - A
Stop nut (p) in the "tall pilot" position
= 2 mm
DETAIL A
Figure 1: Inspection of pedal unit adjustment system
Approved under EASA DOA No. 21J.056  Page 10/14
2009.08.03

### Page 11

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 11/14 
2009.08.03 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2: Inspection and removal/installation of pedal unit adjustment system 
f - 2 
g 
h 
d 
c 
b 
a - 1 
SECTION B - B 
o 
l

### Page 12 (OCR)

eurocopter
an EADS Company
T.F.S. No. 00000528
SECTION C - C
Stop nut (p) in the mid-travel position
×
DETAIL B  Presence of at least one thread
Figure 3: Rework of safetying on pedal unit adjustment system
Approved under EASA DOA No. 21J.056  Page 12/14
2009.08.03

### Page 13

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 13/14 
2009.08.03 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 4: Embodiment of MOD 330A779820.00 
Presence of at least one thread 
m 
Indelible marking of MOD 
No. 330A779820.00

### Page 14

T.F.S. No. 00000528 
Approved under EASA DOA No. 21J.056       Page 14/14 
2009.08.03 
 
 
 
3. MATERIAL INFORMATION 
 
3.A. MATERIAL: PRICE AND AVAILABILITY 
 
3.A.1. Cost 
 
The components listed in paragraph 3.C.1. will be delivered free of charge upon receipt of an order 
from the operator. 
 
3.A.2. Availability 
 
The operator will be notified of the delivery lead time by User Service Sales Directorate. 
 
 
3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT 
 
Not applicable. 
 
 
3.C. EQUIPMENT REQUIRED FOR EACH HELICOPTER/ENGINE/COMPONENT 
 
3.C.1. Kit or component(s) to be ordered for one helicopter or one assembly 
 
Material P/N Qty Item Key Word Instructions 
MP/N SAP     
      
23310CA015015 740025 2 1 Pin  
53301-20-15BCL 1155051 4 2 Pin  
53301-20-25BCL 1173580 4 3a Pin  
53301-20-25BCL 1173580 4 3b Pin  
 
3.C.2. Material to be ordered separately 
 
Material P/N Qty Item Key Word Instructions 
MP/N SAP     
      
330A77-4088-20 330A77408820 AR 4 Half-bushing  
 
3.C.3. Products to be ordered separately 
 
Material P/N Qty Item Key Word Instructions 
MP/N SAP     
      
ASNA4019 1055389 AR 10 Adhesive  
AIR 4210B 1061310 AR 11 Grease  
CN-EC2216B/A 1104301 AR 12 Epoxy adhesive  
 
 
3.D. PROCUREMENT CONDITIONS 
 
Not applicable. 
 
 
4. APPENDIX 
 
Not applicable.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
