# Airbus Service Bulletin 57-P078-00

Copy: No revision named ("SB 57-P078-00"), 236 pages: PDF https://openairdocs.org/files/sha256/65/02/65028aa241667a0ce7b2046b070435bf6bd10af428e861d01b659f3eee66fe88; text https://openairdocs.org/service-documents/airbus/57-p078-00/file/65028aa24166.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2024-1891, the docket of AD 2024-14-10. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: 57-P078-00
- Page: https://openairdocs.org/service-documents/airbus/57-p078-00

## Text (236 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2024-1891, the docket of AD 2024-14-10. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - TRAILING EDGE AND TRAILING EDGE DEVICES - INSPECTION
OF SURFACE TREATMENT AT A350-1000 FLAP SUPPORT STRUCTURE
(FSS)
MODIFICATION No.:
None

### Page 2

A350
SERVICE BULLETIN
SUMMARY
REV 00 Dec 15/23 A350-57-P078
Page 2
ATA SYSTEM: 57
TITLE: WINGS - TRAILING EDGE AND TRAILING EDGE DEVICES - INSPECTION
OF SURFACE TREATMENT AT A350-1000 FLAP SUPPORT STRUCTURE
(FSS)
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
During production of A350 aircraft it has been identified that on several FSS (Flap
Support Structure) components surface protection have not been applied in bush
areas. The surface protection could be potential insufficient edge sealing around
bushing installations, and missing overpaint of the sealant (over-coating with elastic
varnish to protect against hydraulic fluids not performed). This potential insufficient
surface treatment of areas of aluminum parts could results to corrosion initiation
at bushing location. A Detailed inspection (DET) of the identified area has to be
performed for evidence of corrosion. Missing surface treatment should be reapplied at
specific location. In case of finding corrosion repair will be required.
(2) Objective/Action
This Inspection Service Bulletin details the instruction to inspect the affected areas in
the FSS areas and to apply the correct surface protection at specific location.
(3) Advantages
With the accomplishment of this Inspection Service Bulletin the affected areas will be
identified and an efficient surface protection will be applied at specific location.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

### Page 3

A350
SERVICE BULLETIN
SUMMARY
REV 00 Dec 15/23 A350-57-P078
Page 3
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 57P078D01R01 1 3580.00 USD PINS, LOCK-WASHER,
RETAINER RING
Part kit 57P078D02R01 1 3580.00 USD PINS, LOCK-WASHER,
RETAINER RING
TOTAL   7160.00 USD  
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 57P078D03R00 1 3580.00 USD PINS, LOCK-WASHER,
RETAINER RING
Part kit 57P078D04R00 1 3580.00 USD PINS, LOCK-WASHER,
RETAINER RING
TOTAL   7160.00 USD  
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
BAW CPA ETD FWI QTR VIR
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
AIRCRAFT YES
EQUIPMENT NO
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
AIRCRAFT YES
EQUIPMENT NO

### Page 4

A350
SERVICE BULLETIN
SUMMARY
REV 00 Dec 15/23 A350-57-P078
Page 4
I. MANPOWER
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
MANPOWER
TOTAL MAN-HOURS 299.00
h
ELAPSED TIME (HOURS) 49.00 h
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
MANPOWER
TOTAL MAN-HOURS 199.00
h
ELAPSED TIME (HOURS) 32.00 h

### Page 5

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-57XXP078-A-FAPE3-0726J-A-003-01 Fig.SA Sol.AA SHEET 1/1
REV 00 Dec 15/23 A350-57-P078General Overview - Initial and Repetitive Inspection
Page 5
J. GENERAL OVERVIEW
CONF ALL
Z500
Z600
A
A
LH SHOWN
RH SYMMETRICAL
FLAP SUPPORT 3
FLAP SUPPORT 4
A
DO A DETAILED INSPECTION OF THE
PROTECTIVE TREATMENT ON THE FLAP 
SUPPORTS 1, 2, 3, AND 4
FLAP SUPPORT 1
FLAP SUPPORT 2
LEVER 2
ICN-A350-A-57XXP078-A-FAPE3-0726J-A-003-01

### Page 6

A350
SERVICE BULLETIN
SUMMARY
Figure ICN-A350-A-57XXP078-A-FAPE3-0726M-A-003-01 Fig.SB Sol.AA SHEET 1/1
REV 00 Dec 15/23 A350-57-P078General Overview - Repetitive Inspection
Page 6
CONF ALL
Z500
Z600
A
A
LH SHOWN
RH SYMMETRICAL
A
TREATMENT ON THE FLAP SUPPORTS 1 AND 2
FLAP SUPPORT 1
FLAP SUPPORT 2
DO A DETAILED INSPECTION OF THE PROTECTIVE
LEVER 2
ICN-A350-A-57XXP078-A-FAPE3-0726M-A-003-01

### Page 7

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 7
ATA SYSTEM: 57
TITLE: WINGS - TRAILING EDGE AND TRAILING EDGE DEVICES - INSPECTION
OF SURFACE TREATMENT AT A350-1000 FLAP SUPPORT STRUCTURE
(FSS)
1. PLANNING INFORMATION
A. APPLICABILITY
(1) Models
ON A/C 0065, 0071, 0088, 0102, 0110, 0118, 0125, 0141, 0161, 0169, 0188, 0206, 0215,
0225, 0229, 0233, 0241, 0252, 0258, 0262, 0266, 0274, 0286, 0290, 0296, 0298, 0306,
0315, 0319, 0326, 0330, 0332, 0336, 0340, 0342, 0346, 0350, 0356, 0362, 0368, 0372,
0374, 0380, 0382, 0386, 0388, 0399, 0402, 0415, 0420, 0426, 0432, 0446
350-1041
CONF ALL
(2) Applicability by MSN
0065 0071 0088 0102 0110 0118 0125 0141 0161 0169 0188 0206 0215 0225 0229
0233 0241 0252 0258 0262 0266 0274 0286 0290 0296 0298 0306 0315 0319 0326
0330 0332 0336 0340 0342 0346 0350 0356 0362 0368 0372 0374 0380 0382 0386
0388 0399 0402 0415 0420 0426 0432 0446
(3) MSN by configuration
MSN CONFIGURATION
0065 0071 0088 0102 0110 0118 0125 0141 0161 0169 0188
0206 0215 0225 0229 0233 0241 0252 0258 0262 0266 0274
0286 0290 0296 0298 0306 0315 0319 0326 0330 0332 0336
0340 0342 0346 0350 0356 0362 0368 0372 0374 0380 0382
0386 0388 0399 0402 0415 0420 0426 0432 0446
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
During production of A350 aircraft it has been identified that on several FSS (Flap
Support Structure) components surface protection have not been applied in bush
areas. The surface protection could be potential insufficient edge sealing around
bushing installations, and missing overpaint of the sealant (over-coating with elastic
varnish to protect against hydraulic fluids not performed). This potential insufficient
surface treatment of areas of aluminum parts could results to corrosion initiation
at bushing location. A Detailed inspection (DET) of the identified area has to be
performed for evidence of corrosion. Missing surface treatment should be reapplied at
specific location. In case of finding corrosion repair will be required.

### Page 8

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 8
(2) Objective/Action
This Inspection Service Bulletin details the instruction to inspect the affected areas in
the FSS areas and to apply the correct surface protection at specific location.
(3) Advantages
With the accomplishment of this Inspection Service Bulletin the affected areas will be
identified and an efficient surface protection will be applied at specific location.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
1 Do a Detailed Inspection of the LH Flap Support 1 - Location 1 and 2
2 Do a Detailed Inspection of the LH Flap Support 1 - Location 3, 4 and 5
3 Do a Detailed Inspection of the LH Flap Support 2 - Location 1
4 Do a Detailed Inspection of the LH Flap Support 2 - Location 2, 3 and 4
5 Do a Detailed Inspection of the LH Lever 2 on Flap Support 2 - Location 1
and 2
6 Do a Detailed Inspection of the LH Flap Support 3 - Location 1
7 Do a Detailed Inspection of the LH Flap Support 4 - Location 1
8 Do a Detailed Inspection of the RH Flap Support 1 - Location 1 and 2
9 Do a Detailed Inspection of the RH Flap Support 1 - Location 3, 4 and 5
10 Do a Detailed Inspection of the RH Flap Support 2 - Location 1
11 Do a Detailed Inspection of the RH Flap Support 2 - Location 2, 3 and 4
12 Do a Detailed Inspection of the RH Lever 2 on Flap Support 2 - Location 1
and 2
13 Do a Detailed Inspection of the RH Flap Support 3 - Location 1
14 Do a Detailed Inspection of the RH Flap Support 4 - Location 1
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
1 Do a Detailed Inspection of the LH Flap Support 1 - Location 3, 4 and 5
2 Do a Detailed Inspection of the LH Flap Support 2 - Location 2, 3 and 4
3 Do a Detailed Inspection of the LH Lever 2 on Flap Support 2 - Location 1
and 2
4 Do a Detailed Inspection of the RH Flap Support 1 - Location 3, 4 and 5
5 Do a Detailed Inspection of the RH Flap Support 2 - Location 2, 3 and 4
6 Do a Detailed Inspection of the RH Lever 2 on Flap Support 2 - Location 1
and 2
E. COMPLIANCE

### Page 9

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 9
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Union Aviation Safety Agency
(EASA) will be issued to confirm this classification. It is anticipated that the AD will
confirm the thresholds and intervals listed in the table below but reference should be
made to the AD for confirmation of the mandated accomplishment timescale.
T able 1, CONF 001 — Do a detailed inspection for corrosion on the LH and RH Flap
Supports 1, 2, 3 and 4.
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All Aircraft Do a detailed
inspection for
corrosion on
the LH and RH
Flap Supports
1, 2, 3, and 4:
Flap Support 1 –
Location 1, 2, 3,
4, 5 Flap Support
2 – Location 1,
2, 3, 4Lever 2
on Flap Support
2 – Location 1,
2Flap Support
3 – Location
1Flap Support
4 – Location 1
No later than
78 months
after Entry Into
Service (First
Transfer of Title)
None None
Corrosion
is found
Contact AIRBUS Before next flight None None
Corrosion is
not found
Apply required
surface
protection at
locations: Flap
Support 1 –
Location 1, 2
Flap Support
2 – Location 1
Flap Support
3 – Location 1
Flap Support
4 – Location 1
Before next flight None None
  AND
  No Further action None None None
T able 2, CONF 001 — Do a detailed inspection for corrosion on the LH and RH Flap
Supports 1 and 2 – Repetitive Inspection.

### Page 10

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 10
COMPLIANCE TIME
CONDITIONS ACTION
THRESHOLD GRACE PERIOD
REPETITIVE
INTERVAL
All Aircraft Do a detailed
inspection for
corrosion on
the LH and RH
Flap Supports
at locations:
Flap Support 1
– Location 3, 4,
5Flap Support
2 – Location 2,
3, 4Lever 2 –
Location 1, 2
36 months after
last inspection
None 36 month(s)
Corrosion
is found
Contact AIRBUS Before next flight None None
Corrosion is
not found
Repeat the
detailed
inspection
36 months after
last inspection
None 36 month(s)
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
PREPARATION
Job Set-Up 0.50 h
Get Access to the LH Lever Bearing Assembly 1, 2, 3 and 4 50.00 h
Get Access to the RH Lever Bearing Assembly 1, 2, 3 and 4 50.00 h
Do the Preparation of the Inspection Area 4.00 h
PROCEDURE
Do a Detailed Inspection of the LH Flap Support 1 -
Location 1 and 2
4.00 h
Do a Detailed Inspection of the LH Flap Support 1 -
Location 3, 4 and 5
3.00 h

### Page 11

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 11
Do a Detailed Inspection of the LH Flap Support 2 -
Location 1
2.00 h
Do a Detailed Inspection of the LH Flap Support 2 -
Location 2, 3 and 4
5.00 h
Do a Detailed Inspection of the LH Lever 2 on Flap Support
2 - Location 1 and 2
2.00 h
Do a Detailed Inspection of the LH Flap Support 3 -
Location 1
2.00 h
Do a Detailed Inspection of the LH Flap Support 4 -
Location 1
2.00 h
Do a Detailed Inspection of the RH Flap Support 1 -
Location 1 and 2
4.00 h
Do a Detailed Inspection of the RH Flap Support 1 -
Location 3, 4 and 5
3.00 h
Do a Detailed Inspection of the RH Flap Support 2 -
Location 1
2.00 h
Do a Detailed Inspection of the RH Flap Support 2 -
Location 2, 3 and 4
5.00 h
Do a Detailed Inspection of the RH Lever 2 on Flap Support
2 - Location 1 and 2
2.00 h
Do a Detailed Inspection of the RH Flap Support 3 -
Location 1
2.00 h
Do a Detailed Inspection of the RH Flap Support 4 -
Location 1
2.00 h
PREPARATION FOR TEST
Do the Preparation for T est 2.00 h
TEST
T est 2.00 h
CLOSE-UP
Close Access to the LH Lever Bearing Assembly 1, 2, 3 and
4
75.00 h
Close Access to the RH Lever Bearing Assembly 1, 2, 3 and
4
75.00 h
Close-up 0.50 h
TOTAL MAN-HOURS 299.00 h
ELAPSED TIME (HOURS) 49.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix A.
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
PREPARATION
Job Set-Up 0.50 h

### Page 12

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 12
Get Access to the LH Flap Supports 1 and 2 35.00 h
Get Access to the LH Flap Supports 1 and 2 35.00 h
Do the Preparation of the Inspection Area 4.00 h
PROCEDURE
Do a Detailed Inspection of the LH Flap Support 1 -
Location 3, 4 and 5
3.00 h
Do a Detailed Inspection of the LH Flap Support 2 -
Location 2, 3 and 4
5.00 h
Do a Detailed Inspection of the LH Lever 2 on Flap Support
2 - Location 1 and 2
2.00 h
Do a Detailed Inspection of the RH Flap Support 1 -
Location 3, 4 and 5
3.00 h
Do a Detailed Inspection of the RH Flap Support 2 -
Location 2, 3 and 4
5.00 h
Do a Detailed Inspection of the RH Lever 2 on Flap Support
2 - Location 1 and 2
2.00 h
PREPARATION FOR TEST
Do the Preparation for T est 2.00 h
TEST
T est 2.00 h
CLOSE-UP
Close Access to the LH Flap Supports 1 and 2 50.00 h
Close Access to the RH Flap Supports 1 and 2 50.00 h
Close-up 0.50 h
TOTAL MAN-HOURS 199.00 h
ELAPSED TIME (HOURS) 32.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix B.
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4
(a) T ask set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE TREATMENT
AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-21-11-00ZZZ-660Z-A A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-XX-01ZZZ-667Z-A A350-A-51-75-12-00ZZZ-660Z-A

### Page 13

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 13
CONSUMABLE MATERIAL LIST (CML)
See manual
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-27-54-58-00ZZZ-520Z-A
A350-A-27-54-58-00ZZZ-720Z-A
A350-A-27-54-59-00ZZZ-520Z-A
A350-A-27-54-59-00ZZZ-720Z-A
A350-A-27-54-78-00ZZZ-520Z-A
A350-A-27-54-78-00ZZZ-720Z-A
A350-A-51-78-XX-00ZZZ-25BZ-A A350-A-57-51-85-08ZZZ-520Z-A
A350-A-57-51-85-0AZZZ-720Z-A
A350-A-57-54-62-00ZZZ-720Z-A A350-A-57-54-71-00ZZZ-520Z-A
A350-A-57-54-71-00ZZZ-720Z-A
A350-A-57-57-61-00ZZZ-720Z-A
A350-A-57-57-61-02ZZZ-720Z-A
A350-A-57-57-62-00ZZZ-720Z-A
A350-A-57-57-62-01ZZZ-720Z-A
A350-A-57-57-62-02ZZZ-720Z-A
A350-A-57-57-62-03ZZZ-720Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A
STANDARDS MANUAL (SM)
See manual
(b) T ask set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
AIRCRAFT STRUCTURAL REPAIR (ASR)
A350-A-51-24-XX-01ZZZ-667Z-A
CONSUMABLE MATERIAL LIST (CML)
See manual
ELECTRICAL STANDARD PRACTICES (ESP)
A350-A-20-55-XX-01ZZZ-042Z-A
INTRODUCTION (INTRO)
A350-A-00-61-04-11ZZZ-018Z-D
MAINTENANCE PROCEDURE (MP)
A350-A-24-41-XX-00ZZZ-170Z-A A350-A-27-54-58-00ZZZ-520Z-A
A350-A-27-54-58-00ZZZ-720Z-A

### Page 14

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 14
MAINTENANCE PROCEDURE (MP)
A350-A-27-54-59-00ZZZ-520Z-A
A350-A-27-54-59-00ZZZ-720Z-A
A350-A-27-54-78-00ZZZ-720Z-A
A350-A-51-78-XX-00ZZZ-25BZ-A A350-A-57-51-85-08ZZZ-520Z-A
A350-A-57-51-85-0AZZZ-720Z-A
A350-A-57-54-62-00ZZZ-720Z-A A350-A-57-54-71-00ZZZ-520Z-A
A350-A-57-54-71-00ZZZ-720Z-A
A350-A-57-57-61-00ZZZ-720Z-A
A350-A-57-57-61-02ZZZ-720Z-A
A350-A-57-57-62-00ZZZ-720Z-A
A350-A-57-57-62-01ZZZ-720Z-A
A350-A-57-57-62-02ZZZ-720Z-A
A350-A-57-57-62-03ZZZ-720Z-A
SYSTEM DESCRIPTION (SD)
A350-A-06-3X-XX-01ZZZ-04CZ-A
STANDARDS MANUAL (SM)
See manual
K. PUBLICATION AFFECTED
None
L. INDUSTRY SUPPORT INFORMATION
For the initial inspection done at the 72 months check, AIRBUS will credit the man-hours
indicated in this Service Bulletin at the agreed in-house warranty labor rate. Claims for
this allowance shall be received no later than 90 days after completion of the last affected
aircraft of your fleet fulfilling above timeframe conditions.
AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kits
at no charge for orders placed before 31 December 2026.

### Page 15

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 15
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 57P078D01R01 1
Part kit 57P078D02R01 1
Referenced parts See SB
Material for task set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF SURFACE
TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
MATERIAL QTY SEE NOTES
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Part kit 57P078D03R00 1
Part kit 57P078D04R00 1
Referenced parts See SB
B. TOOLING
Referenced tools for task set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-27-54-78-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A
Referenced tools for task set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-27-54-78-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A

### Page 16

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 16
C. CONSUMABLES
Consumables for task set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
03FDB1 Mineral Oil base Grease -Anti-FrettingPaste
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
04QAB2 Coating - - FlexibleStructure
04SAB2 Varnish Polyurethane - -Marking Structure
06AAC1 Polysulfide Sealant -General Purpose Interfay
06ACA1
Polysulfide Sealant - Low
Density MultiPurpose
Brushable
06ACB1 Polysulfide Sealant - LowDensity MultiPurpose Fillet
06LCB1
Non Hardening Jointing
Putty - Medium T emp. Area
Chromate Free
08BAA9 Non Aqueous Cleaner -General
10ABC1
Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
12AEB1
Corrosion Preventive
Compound - Heavy Duty
Long Durability Hard Film
14SBA1 T extile - Lint free Cotton
Consumables for task set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
03FDB1 Mineral Oil base Grease -Anti-FrettingPaste
04QAB2 Coating - - FlexibleStructure
04SAB2 Varnish Polyurethane - -Marking Structure
06AAC1 Polysulfide Sealant -General Purpose Interfay
06ACB1 Polysulfide Sealant - LowDensity MultiPurpose Fillet

### Page 17

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 17
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced consumables for task set A350-A-57-XX-P078-01000-93BA-A
INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL
INSPECTION
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-27-54-78-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-62-01ZZZ-720Z-A
Ref. MP A350-A-57-57-62-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-03ZZZ-720Z-A
Referenced consumables for task set A350-A-57-XX-P078-01000-93BB-A
INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 -
REPETITIVE INSPECTION
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-27-54-78-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-62-01ZZZ-720Z-A
Ref. MP A350-A-57-57-62-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-03ZZZ-720Z-A

### Page 18

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 18
D. LIST OF NEW PARTS
Part kit 57P078D01R01
Cost 3580.00 USD
Availability 220 d (calendar days from receipt of order)
NOTE(S)
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 V5757653420000 1 WASHER
10 MS24665-308 1 PIN
11 MS24665-310 1 PIN
33 ABS1149AP2625B 1 WASHER
36 V5757102420000 1 WASHER
41 MS16624-4102 1 RING
67 V5757632220000 1 WASHER
73 ABS1149AP2500B 1 WASHER
82 MS24665-380 1 PIN
83 MS16624-4143 1 RING
90 MS24665-309 2 PIN
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Part kit 57P078D02R01
Cost 3580.00 USD
Availability 220 d (calendar days from receipt of order)
NOTE(S)

### Page 19

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 19
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 V5757653420000 1 WASHER
10 MS24665-308 1 PIN
11 MS24665-310 1 PIN
33 ABS1149AP2625B 1 WASHER
36 V5757102420000 1 WASHER
41 MS16624-4102 1 RING
67 V5757632220000 1 WASHER
73 ABS1149AP2500B 1 WASHER
82 MS24665-380 1 PIN
83 MS16624-4143 1 RING
90 MS24665-309 2 PIN
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Part kit 57P078D03R00
Cost 3580.00 USD
Availability 090 d (calendar days from receipt of order)
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com

### Page 20

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 20
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 V5757653420000 1 WASHER
11 MS24665-310 1 PIN
33 ABS1149AP2625B 1 WASHER
36 V5757102420000 1 WASHER
41 MS16624-4102 1 RING
67 V5757632220000 1 WASHER
73 ABS1149AP2500B 1 WASHER
82 MS24665-380 1 PIN
83 MS16624-4143 1 RING
90 MS24665-309 2 PIN
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Part kit 57P078D04R00
Cost 3580.00 USD
Availability 090 d (calendar days from receipt of order)
Procurement address D4296
AIRBUS
Material, Logistics and Suppliers ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51775
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 V5757653420000 1 WASHER
11 MS24665-310 1 PIN
33 ABS1149AP2625B 1 WASHER
36 V5757102420000 1 WASHER
41 MS16624-4102 1 RING
67 V5757632220000 1 WASHER
73 ABS1149AP2500B 1 WASHER
82 MS24665-380 1 PIN
83 MS16624-4143 1 RING

### Page 21

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 21
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
90 MS24665-309 2 PIN
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
Referenced parts for task set A350-A-57-XX-P078-01000-93BA-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
T o accomplish this Service Bulletin it is necessary to use the expendable parts listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-62-01ZZZ-720Z-A
Ref. MP A350-A-57-57-62-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-03ZZZ-720Z-A
Referenced parts for task set A350-A-57-XX-P078-01000-93BB-A INSPECTION OF
SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - REPETITIVE INSPECTION
T o accomplish this Service Bulletin it is necessary to use the expendable parts listed in:
Ref. MP A350-A-27-54-58-00ZZZ-720Z-A
Ref. MP A350-A-27-54-59-00ZZZ-720Z-A
Ref. MP A350-A-57-51-85-0AZZZ-720Z-A
Ref. MP A350-A-57-54-62-00ZZZ-720Z-A
Ref. MP A350-A-57-54-71-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-00ZZZ-720Z-A
Ref. MP A350-A-57-57-61-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-00ZZZ-720Z-A
Ref. MP A350-A-57-57-62-01ZZZ-720Z-A
Ref. MP A350-A-57-57-62-02ZZZ-720Z-A
Ref. MP A350-A-57-57-62-03ZZZ-720Z-A
E. LIST OF EXISTING PARTS
No parts

### Page 22

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 22
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A350-A-57-XX-P078-01000-93BA-A (A350-A-57-XX-P078-01ZZZ-93BZ-A)
INSPECTION OF SURFACE TREATMENT AT FLAP SUPPORTS 1, 2, 3, AND 4 - INITIAL INSPECTION
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SheetING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESP A350-A-20-55-XX-01ZZZ-
042Z-A.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
NOTE: Discarded parts must be managed at the operator's discretion.

### Page 23

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 23
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 299.00 h
ELAPSED TIME (HOURS) 49.00 h
B. PREPARATION
(1) Task A350-A-57-XX-P078-01001-540A-A (A350-A-57-XX-P078-01ZZZ-540Z-A)
Job Set-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
INTRO A350-A-00-61-04-11ZZZ-018Z-D
MP A350-A-24-41-XX-00ZZZ-170Z-A
Procedure
NOTE: For the basic Aircraft configuration, refer to Ref. INTRO A350-A-00-61-04-
11ZZZ-018Z-D "Maintenance Procedure - Introduction".
(a) Make sure that the aircraft is electrically grounded, refer to Ref. MP A350-A-24-
41-XX-00ZZZ-170Z-A.
(2) Task A350-A-57-XX-P078-06001-540A-A (A350-A-57-XX-P078-06ZZZ-540Z-A)
Get Access to the LH Lever Bearing Assembly 1, 2, 3 and 4
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
197
531 Access Panel 531AB, Panel 531DB
532 Access Panel 532AB, Panel 532DB
533 Access Panel 533AB, Panel 533DB
Manpower/Resources/Skills
Man-hours 50.00 h
Minimum Number of person 5
Elapsed Time 10.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-27-54-58-00ZZZ-520Z-AA350-A-27-54-59-00ZZZ-520Z-A

### Page 24

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 24
Manuals/Drawings References/Sheets
A350-A-27-54-78-00ZZZ-520Z-A
A350-A-57-51-85-08ZZZ-520Z-A
A350-A-57-54-71-00ZZZ-520Z-A
Procedure
(a) Do the Job Set-Up procedure as specified in the Removal of the Lever Bearing
Assembly, refer to Ref. MP A350-A-27-54-78-00ZZZ-520Z-A.
(b) Do the Job Set-Up procedure for the Flap Support Lever 2 as specified in the
Removal of Flap Support Levers 1 and 2, refer to Ref. MP A350-A-57-54-71-
00ZZZ-520Z-A.
(c) Do the Job Set-Up procedure as specified in the Removal of the Pivot T ube from
Flap Support 2, refer to Ref. MP A350-A-57-51-85-08ZZZ-520Z-A.
(d) Do the Job Set-Up procedure as specified in the Removal of the Flap Moving
Damper, refer to Ref. MP A350-A-27-54-59-00ZZZ-520Z-A.
(e) Do the Job Set-Up procedure for the Drive Strut on Flap Support 2 as specified in
the Removal of the Drive Strut of Flap Supports 2 and 3, refer to Ref. MP A350-A-
27-54-58-00ZZZ-520Z-A.
(3) Task A350-A-57-XX-P078-08001-540A-A (A350-A-57-XX-P078-08ZZZ-540Z-A)
Get Access to the RH Lever Bearing Assembly 1, 2, 3 and 4
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
198
631 Access Panel 631AB, Panel 631DB
632 Access Panel 632AB, Panel 632DB
633 Access Panel 633AB, Panel 633DB
Manpower/Resources/Skills
Man-hours 50.00 h
Minimum Number of person 5
Elapsed Time 10.00 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
MP
A350-A-27-54-58-00ZZZ-520Z-A
A350-A-27-54-59-00ZZZ-520Z-A
A350-A-27-54-78-00ZZZ-520Z-A
A350-A-57-51-85-08ZZZ-520Z-A
A350-A-57-54-71-00ZZZ-520Z-A
Procedure
(a) Do the Job Set-Up procedure as specified in the Removal of the Lever Bearing
Assembly, refer to Ref. MP A350-A-27-54-78-00ZZZ-520Z-A.

### Page 25

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 25
(b) Do the Job Set-Up procedure for the Flap Support Lever 2 as specified in the
Removal of Flap Support Levers 1 and 2, refer to Ref. MP A350-A-57-54-71-
00ZZZ-520Z-A.
(c) Do the Job Set-Up procedure as specified in the Removal of the Pivot T ube from
Flap Support 2, refer to Ref. MP A350-A-57-51-85-08ZZZ-520Z-A.
(d) Do the Job Set-Up procedure as specified in the Removal of the Flap Moving
Damper, refer to Ref. MP A350-A-27-54-59-00ZZZ-520Z-A.
(e) Do the Job Set-Up procedure for the Drive Strut on Flap Support 2 as specified in
the Removal of the Drive Strut of Flap Supports 2 and 3, refer to Ref. MP A350-A-
27-54-58-00ZZZ-520Z-A.
(4) Task A350-A-57-XX-P078-01001-258A-A (A350-A-57-XX-P078-01ZZZ-258Z-A)
Do the Preparation of the Inspection Area
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
197
198
531
532
533
631
632
633
Manpower/Resources/Skills
Man-hours 4.00 h
Minimum Number of person 4
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
MP A350-A-51-78-XX-00ZZZ-25BZ-A
Procedure
(a) Make sure the inspection areas are sufficiently clean to perform detailed
inspection.
(b) If not, clean the inspection area with:
  T extile - Lint free Cotton14SBA1

### Page 26

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 26
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
(c) If there is a T emporary Protection System (TPS) layer and if it does not let you do
a satisfactory inspection, remove the TPS layer, refer to Ref. MP A350-A-51-78-
XX-00ZZZ-25BZ-A.
(d) If necessary, use a flashlight to do the inspection.
(e) If necessary, use a inspection mirror to do the inspection.
C. PROCEDURE
(1) Task A350-A-57-XX-P078-01001-311A-A (A350-A-57-XX-P078-01ZZZ-311Z-A)
Do a Detailed Inspection of the LH Flap Support 1 - Location 1 and 2
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
197
Manpower/Resources/Skills
Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
03FDB1 Mineral Oil base Grease -Anti-FrettingPaste
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
04QAB2 Coating - - FlexibleStructure
04SAB2 Varnish Polyurethane - -Marking Structure
06ACA1
Polysulfide Sealant - Low
Density MultiPurpose
Brushable
06LCB1
Non Hardening Jointing
Putty - Medium T emp. Area
Chromate Free
08BAA9 Non Aqueous Cleaner -General
10ABC1
Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow

### Page 27

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 27
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
12AEB1
Corrosion Preventive
Compound - Heavy Duty
Long Durability Hard Film
14SBA1 T extile - Lint free Cotton
Part kit 57P078D01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 MS24665-308 1 PIN
Referenced Information
Manuals/Drawings References/Sheets
ASR
A350-A-51-21-11-00ZZZ-660Z-A
A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
Ref. Fig.BA Detailed Inspection of Flap Support 1 - Location 1 and 2.
NOTE: T o aid in the inspection, refer to Ref. Fig.FA Flow Chart.
(a) The Standard Practices given in this procedure are:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-XX-
01ZZZ-667Z-A.
3 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
4 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
5 Repair the paint coating in accordance with Ref. ASR A350-A-51-75-12-
00ZZZ-660Z-A.
6 Repair the protective treatment of metal parts in accordance with Ref. ASR
A350-A-51-21-11-00ZZZ-660Z-A.
7 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
8 T ag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a detailed inspection of the LH Flap Support 1, location 1– Bushing on the
second load bolt of Flap Support 1.
WARNING: USE GOGGLES EACH TIME YOU CUT A COTTER PIN. REMOVE
AND DISCARD THE COTTER PIN IMMEDIATELY.
1 Cut, remove and discard the Cotter Pin, item (10), refer to Sheet 03.
1 Cotter Pin   Item (10) Discard

### Page 28

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 28
2 Remove and retain the Locking Cap, item (12), Nut, item (13), Washer,
item (14) and Failsafe Bolt, item (15), refer to Sheet 03.
1 Locking Cap   Item (12) Retain
1 Nut   Item (13) Retain
1 Washer   Item (14) Retain
1 Failsafe Bolt   Item (15) Retain
3 Clean the retained parts, component interfaces, and adjacent area with:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
4 Do a detailed inspection of the bushes interface (without the flange). Make
sure there is no corrosion or damage to the surface protection, refer to
Sheet 03, Sheet 04, Section B-B, and Sheet 05.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next work step.
5 Apply a surface protection if necessary.
a If necessary, repair protective treatment on the aluminum structure
with:
  Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
10ABC1  
b If necessary, repair paint coating on the aluminum structure with:
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
and
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4  
c If necessary, apply fillet sealant around the edge of the bushes, refer
to Sheet 04, Section A-A and Sheet 05. Use:
  Polysulfide Sealant
- Low Density
MultiPurpose Brushable
06ACA1  
d If necessary, apply protection coating to the exposed fillet sealant,
refer to Sheet 04, Section A-A and Sheet 05. Use:
  Coating - - Flexible
Structure
04QAB2  
6 Do a visual inspection on the retained parts, component interfaces and the
adjacent area to make sure they are in good condition, refer to Sheet 03.

### Page 29

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 29
7 Apply a thin layer of anti-fretting paste to the uncoated mating surface and
the thread of the Failsafe Bolt, item (15).
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
8 Install the Failsafe Bolt, item (15), refer to Sheet 03 and Sheet 05.
1 Failsafe Bolt   Item (15) Retained
9 Install the Washer, item (14) and Nut, item (13), refer to Sheet 03 and
Sheet 05.
1 Nut   Item (13) Retained
1 Washer   Item (14) Retained
10 T orque the Nut, item (13) to between 75.0 and 81.0 Nm (55.32 and 59.74
lb.ft).
11 Install the Locking Cap, item (12), and Cotter Pin, item 10, refer to Sheet
03 and Sheet 05.
1 Locking Cap   Item (12) Retained
1 PIN-COTTER MS24665-308 Item 10
12 Mark a red line across the Nut, item (13) and onto the adjacent structure
with:
  Varnish Polyurethane - -
Marking Structure
04SAB2  
NOTE: The line must have an approximate width of 3.5 mm (0.14 in.)
Continue the line across the surface of the adjacent structure to a
distance of approximately 5 mm (0.2 in.).
CAUTION: DO NOT REMOVE GROUP 1 AND GROUP 2 BOLTS AT THE SAME
TIME. DAMAGE TO THE COMPONENT CAN OCCUR.
(c) Do a detailed inspection of the LH Flap Support 1, location 2– Lever Bearing
Assembly for Group 1.
1 Remove and retain Nuts, item (8), Washers, item (7), and Bolts, item (6),
from Group 1 fastener locations. Refer to Sheet 02.
3 NUT   Item (8) Retain
6 WASHER   Item (7) Retain
3 BOLT   Item (6) Retain
2 Clean the retained parts, component interfaces, and adjacent area with:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
3 Do a detailed inspection of the bushes interface. Make sure there is no
corrosion or damage to the surface protection, refer to Sheet 02.
a If there is corrosion, contact AIRBUS.

### Page 30

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 30
b If there is no corrosion, continue to the next step.
4 Apply a surface protection if necessary.
a If necessary, repair protective treatment on the aluminum structure
with:
  Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
10ABC1  
b If necessary, repair paint coating on the aluminum structure with:
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
and
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4  
c If necessary, apply fillet sealant around the edge of the bushes, refer
to Sheet 04, Section A-A and Sheet 05. Use:
  Polysulfide Sealant
- Low Density
MultiPurpose Brushable
06ACA1  
d If necessary, apply protection coating to the exposed fillet sealant,
refer to Sheet 04, Section A-A and Sheet 05. Use:
  Coating - - Flexible
Structure
04QAB2  
5 Apply a thin layer of jointing putty on the shafts of the retained Bolts, item
(6), Washers, item (7), and Nuts, item (8). Use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
6 Apply a thin layer of jointing putty between the Washers and the mating
surfaces of the Washers, and aircraft structure under the nut, use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
7 Install Nuts, item (8), Washers, item (7), and Bolts, item (6), refer to Sheet
02.
3 NUT   Item (8) Retained
6 WASHER   Item (7) Retained
3 BOLT   Item (6) Retained
8 T orque the Nuts between 138.7 and 166.4 Nm (102.30 and 122.73 lb.ft).
9 Apply corrosion prevention compound to the head of the Bolts, Washers,
and Nuts. Use:
  Corrosion Preventive
Compound - Heavy
12AEB1

### Page 31

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 31
Duty Long Durability
Hard Film
CAUTION: DO NOT REMOVE GROUP 1 AND GROUP 2 BOLTS AT THE SAME
TIME. DAMAGE TO THE COMPONENT CAN OCCUR.
(d) Do a detailed inspection of the LH Flap Support 1, location 2– Lever Bearing
Assembly for Group 2.
1 Remove and retain Nuts, item (8), Washers, item (7), and Bolts, item (6),
from Group 2 fastener locations. Refer to Sheet 02.
2 NUT   Item (8) Retain
4 WASHER   Item (7) Retain
2 BOLT   Item (6) Retain
2 Clean the retained parts, component interfaces, and adjacent area with:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
3 Do a detailed inspection of the bushes interface. Make sure there is no
corrosion or damage to the surface protection, refer to Sheet 02.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
4 Apply a surface protection if necessary.
a If necessary, repair protective treatment on the aluminum structure
with:
  Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
10ABC1  
b If necessary, repair paint coating on the aluminum structure with:
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
and
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4  
c If necessary, apply fillet sealant around the edge of the bushes, refer
to Sheet 04, Section A-A and Sheet 05. Use:
  Polysulfide Sealant
- Low Density
MultiPurpose Brushable
06ACA1  
d If necessary, apply protection coating to the exposed fillet sealant,
refer to Sheet 04, Section A-A and Sheet 05. Use:
  Coating - - Flexible
Structure
04QAB2

### Page 32

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 32
5 Apply a thin layer of jointing putty on the shafts of the retained Bolts, item
(6), Washers, item (7), and Nuts, item (8). Use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
6 Apply a thin layer of jointing putty between the Washers and the mating
surfaces of the Washer, and aircraft structure under the nut, use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
7 Install Nuts, item (8), Washers, item (7), and Bolts, item (6), refer to Sheet
02.
2 NUT   Item (8) Retained
4 WASHER   Item (7) Retained
2 BOLT   Item (6) Retained
8 T orque the Nuts between 138.7 and 166.4 Nm (102.30 and 122.73 lb.ft).
9 Apply corrosion prevention compound to the head of the Bolts, Washers,
and Nuts. Use:
  Corrosion Preventive
Compound - Heavy
Duty Long Durability
Hard Film
12AEB1

### Page 33

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726P-A-002-01 Fig.BA Sol.AA SHEET 1/5
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 1 and 2
Page 33
CONF ALL
A
LH SHOWN
RH SYMMETRICAL
A LH
RH
A
Z197
Z198
FR35
FR74
C
B
FLAP SUPPORT 1
LOCATION 1
LOCATION 2
ICN-A350-A-57XXP078-A-FAPE3-0726P-A-002-01

### Page 34

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726Q-A-003-01 Fig.BA Sol.AA SHEET 2/5
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 1 and 2
Page 34
CONF ALL
LH SHOWN
RH SYMMETRICAL
B x5
NOTE:
REFER TO SHEET 05 FOR THE APPLICABLE NOTES
FLAP SUPPORT 1
LEVER BEARING 
ASSEMBLY
(7)
03
01
x5(6)
(8)
(7)
A
A
04
07
06
01 0708
0708
08 0702
x5
x505
05
0605
LOCATION 2
ICN-A350-A-57XXP078-A-FAPE3-0726Q-A-003-01

### Page 35

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726R-A-003-01 Fig.BA Sol.AA SHEET 3/5
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 1 and 2
Page 35
CONF ALL
C
LH SHOWN
RH SYMMETRICAL
NOTE:
REFER TO SHEET 05 FOR THE APPLICABLE NOTES
FLAP SUPPORT 1
(10) (12) (13) (14)
(15)
10
09
10
11
B
B
BUSH
LOCATION 1
ICN-A350-A-57XXP078-A-FAPE3-0726R-A-003-01

### Page 36

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726S-A-002-01 Fig.BA Sol.AA SHEET 4/5
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 1 and 2
Page 36
CONF ALL
LH SHOWN
RH SYMMETRICAL
B B
E
D
FWD
I
N
B
D
NOTE:
REFER TO SHEET 05 FOR THE APPLICABLE NOTES
FLAP SUPPORT 1
BUSH
ALUMINUM
STRUCTURE
FILLET SEALANT
1312
15
TYPICAL VIEW
14
A A
BUSH BUSH
ICN-A350-A-57XXP078-A-FAPE3-0726S-A-002-01

### Page 37

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726T-A-003-01 Fig.BA Sol.AA SHEET 5/5
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 1 and 2
Page 37
CONF ALL
BUSH
ALUMINUM
STRUCTURE
FILLET SEALANT
1312
15
TYPICAL VIEW
14
D
E
BUSH
ALUMINUM
STRUCTURE
FILLET SEALANT14
1312
15
TYPICAL VIEW
06
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB1, ON THE SHAFTS04
08
TORQUE THE NUT TO BETWEEN 138.7 AND 166.4 Nm (102.30 AND 122.73 lb.ft)07
GROUP 202
NOTE:
GROUP 101
DO NOT REMOVE BOLT WITH ELECTRICAL BONDING03
APPLY A THIN LAYER OF ANTI-FRETTING MATERIAL No. 03FDB1 EVENLY ON THE FAIL SAFE BOLT09
MARK A RED LINE WITH MATERIAL No. 04SAB2 ACROSS THE NUT TO THE ADJACENT STRUCTURE11
TORQUE THE NUT TO BETWEEN 75.0 AND 81.0 Nm (55.32 AND 59.74 lb.ft)10
13
APPLY SURFACE TREATMENT MATERIAL No. 10ABC1 AS NECESSARY12
APPLY COATING MATERIAL No 04QAB2 TO THE EXPOSED SEALANT15
APPLY FILLET SEALANT MATERIAL No. 06ACA1 AROUND THE EDGE OF THE BUSH AS NECESSARY14
APPLY SURFACE PROTECTION MATERIAL No. 04DAB2 AND 04JME4 ON THE ALUMINUM STRUCTURE
AS NECESSARY
DO A DETAILED INSPECTION AROUND THE BUSH EDGE FOR CORROSION ON THE
ALUMINUM STRUCTURE
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB105
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB1, BETWEN THE WASHER AND
STRUCTURE
ICN-A350-A-57XXP078-A-FAPE3-0726T-A-003-01

### Page 38

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01 Fig.FA Sol.AA SHEET 1/1
REV 00 Dec 15/23 A350-57-P078Flow Chart
Page 38
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS
OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
NOTE:
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
NO
YES
YES
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
YES
CONTACT
AIRBUS
01 FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
FLAP SUPPORT 1 - LOCATION 3, 4, 5
FLAP SUPPORT 2 - LOCATION 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
01
REPEAT THE DETAILED INSPECTION FOR CORROSION
ON THE LH AND RH FLAP SUPPORTS 1 AND 2 WITHIN 
THE REPETITIVE INTERVAL AT LOCATIONS: FLAP SUPPORT 1 - LOCATION 1 AND 2
FLAP SUPPORT 2 - LOCATION 1
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
APPLY REQUIRED SURFACE
PROTECTION AT LOCATIONS:
FLAP SUPPORT 1 - LOCATION 1, 2, 3, 4, 5
FLAP SUPPORT 2 - LOCATION 1, 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
DO A DETAILED INSPECTION FOR CORROSION ON
THE LH AND RH FLAP SUPPORTS 1, 2, 3, AND 4:
NO
ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01

### Page 39

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 39
(2) Task A350-A-57-XX-P078-24001-311A-A (A350-A-57-XX-P078-24ZZZ-311Z-A)
Do a Detailed Inspection of the LH Flap Support 1 - Location 3, 4 and 5
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
197
Manpower/Resources/Skills
Man-hours 3.00 h
Minimum Number of person 3
Elapsed Time 1.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
03FDB1 Mineral Oil base Grease -Anti-FrettingPaste
04SAB2 Varnish Polyurethane - -Marking Structure
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Part kit 57P078D01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
11 MS24665-310 1 PIN
33 ABS1149AP2625B 1 WASHER
36 V5757102420000 1 WASHER
41 MS16624-4102 1 RING
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-24-XX-01ZZZ-667Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
Ref. Fig.BE Detailed Inspection of Flap Support 1 - Location 3, 4 and 5
NOTE: T o aid in the inspection, refer to Ref. Fig.FA Flow Chart.
(a) The Standard Practices given in this procedure are:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.

### Page 40

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 40
3 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
5 T ag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a detailed inspection of the LH Flap Support 1, location 3 – Lever 1
attachment. Refer to Sheet 01 and Sheet 02.
WARNING: USE GOGGLES EACH TIME YOU CUT A COTTER PIN. REMOVE
AND DISCARD THE COTTER PIN IMMEDIATELY.
1 Cut, remove and discard the Cotter Pin, item (11).
1 Cotter Pin   Item (11) Discard
2 Remove and discard the Retaining Ring, item (41).
1 Retaining Ring   Item (41) Discard
3 Remove the Locking Cap, item (40).
1 Locking Cap   Item (40) Retain
4 Remove the Nut, item (39), and the Cap Washer, item (38).
1 Nut   Item (39) Retain
1 Cap Washer   Item (38) Retain
5 Unlock the tabs of the Lock Washer, item (36).
6 Remove the Spanner Nut, item (37).
1 Spanner Nut   Item (37) Retain
7 Remove and discard the Lock Washer, item (36).
1 Lock Washer   Item (36) Discard
8 Remove the Washer, item (35).
1 Washer   Item (35) Retain
9 Unlock the tabs of the Lock Washer, item (33).
10 Remove the Spanner Nut, item (34).
1 Spanner Nut   Item (34) Retain
11 Remove and discard the Lock Washer, item (33).
1 Lock Washer   Item (33) Discard
12 Remove the Washer, item (32).
1 Washer   Item (32) Retain
13 Clean the inspection area, retained parts and component interfaces. Use:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9

### Page 41

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 41
14 Do a detailed inspection of the bush interface (without the flange). Make
sure there is no damage to the surface protection. refer to Sheet 02.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
15 Do a visual inspection on the retained parts, component interfaces and the
adjacent area to make sure they are in good condition.
16 Apply a thin layer of anti-fretting paste on the Spanner Nuts, item (34) and
item (37).
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
17 Install the Washer, item (32).
1 Washer   Item (32) Retained
18 Install the new Lock Washer, item 33.
1 WASHER-KEY ABS1149AP2625B Item 33
19 Install the Spanner Nut, item (34) with space between the Washer, item
(32) and the support lug.
1 Spanner Nut   Item (34) Retained
20 Install the Washer, item (35), the new Lock Washer, item 36 and the
Spanner Nut, item (37).
1 Washer   Item (35) Retained
1 WASHER V5757102420000 Item 36
1 Spanner Nut   Item (37) Retained
21 T orque the Spanner Nut, item (37) to between 110.0 and 130.0 Nm (81.13
and 95.88 lb.ft).
22 Make sure there is a space in between the Washer, item (32) and the
support lug.
23 T urn the Spanner Nut, item (34) inboard until the Washer, item (32)
touches the support lug and apply the initial torque as follows:
a T orque the Spanner Nut, item (34) to between 20.0 and 25.0 Nm
(14.76 and 18.43 lb.ft).
24 Safety the Spanner Nut, item (34) with the new Lock Washer, item 33.
25 Safety the Spanner Nut, item (37) with the new Lock Washer, item 36.
26 Install the Cap Washer, item (38) and the Nut, item (39).
1 Cap Washer   Item (38) Retained
1 Nut   Item (39) Retained
27 T orque the Nut, item (39) to between 50.0 and 55.0 Nm (36.88 and 40.56
lb.ft).
28 Install the Locking Cap, item (40).
1 Locking Cap   Item (40) Retained

### Page 42

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 42
29 Install the new Retaining Ring, item 41.
1 RING-RETAINING MS16624-4102 Item 41
30 Install the new Cotter Pin, item 11.
1 PIN-COTTER MS24665-310 Item 11
31 Mark a red line across the Nuts, item (34), item (37) and item (39) to the
adjacent structure with:
  Varnish Polyurethane - -
Marking Structure
04SAB2  
NOTE: The line must have an approximate width of 3.5 mm (0.14 in.)
Continue the line across the surface of the adjacent structure to a
distance of approximately 5 mm (0.2 in.).
(c) Do a detailed inspection of the LH Flap Support 1, location 4 – Upper attachment
of Flap Support 1.
1 Do a detailed inspection of the bush interface (without the flange). Make
sure there is no damage to the surface protection, refer to Sheet 01 and
Sheet 03.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
(d) Do a detailed inspection of the LH Flap Support 1, location 5 – First load path of
Flap Support 1.
1 Do a detailed inspection of the bush interface (without the flange). Make
sure there is no damage to the surface protection, refer to Sheet 01 and
Sheet 04.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.

### Page 43

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726U-A-002-01 Fig.BE Sol.AA SHEET 1/4
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 3, 4 and 5
Page 43
CONF ALL
A
LH SHOWN
RH SYMMETRICAL
A LH
RH
Z197
Z198
FR35
FR74
B
B B A
A
FLAP SUPPORT 1
LEVER 1
A
LOCATION 3
`
LOCATION 4
LOCATION 5
ICN-A350-A-57XXP078-A-FAPE3-0726U-A-002-01

### Page 44

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726V-A-002-01 Fig.BE Sol.AA SHEET 2/4
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 3, 4 and 5
Page 44
CONF ALL
36
(37)
(38)
(39)
(40)
(41)(11)
(32)
33
(34)
(35)
01
B
LH SHOWN
RH SYMMETRICAL
11 41
(36)
(33)
NOTE:
REFER TO SHEET 04 FOR THE APPLICABLE NOTES
02 04 06
02 03 06
05 06
FLAP SUPPORT 1
LEVER 1
LOCATION 3
ICN-A350-A-57XXP078-A-FAPE3-0726V-A-002-01

### Page 45

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726W-A-003-01 Fig.BE Sol.AA SHEET 3/4
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 3, 4 and 5
Page 45
CONF ALL
NOTE:
REFER TO SHEET 04 FOR THE APPLICABLE NOTES
A A
VIEW LOOKING FWD
INBD
LH SHOWN
RH SYMMETRICAL
01
FLAP SUPPORT 1
LOCATION 4
BUSH
01
ICN-A350-A-57XXP078-A-FAPE3-0726W-A-003-01

### Page 46

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726X-A-004-01 Fig.BE Sol.AA SHEET 4/4
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 1 - Location 3, 4 and 5
Page 46
CONF ALL
TORQUE THE NUT, ITEM (39), TO BETWEEN 50.0 AND 55.0 Nm (36.88 AND 40.56 lb.ft)05
TORQUE THE SPANNER NUT, ITEM (34), TO BETWEEN 20.0 AND 25.0 Nm (14.76 AND 18.43 lb.ft)04
MARK A RED LINE WITH MATERIAL No. 04SAB2 ACROSS THE NUTS TO THE ADJACENT STRUCTURE06
APPLY A THIN LAYER OF ANTI-FRETTING MATERIAL No. 03FDB1 EVENLY02
NOTE:
01
TORQUE THE SPANNER NUT, ITEM (37), TO BETWEEN 110.0 AND 130.0 Nm (81.13 AND 95.88 lb.ft)03
DO A DETAILED INSPECTION AROUND THE BUSH EDGE FOR CORROSION ON THE
ALUMINUM STRUCTURE
B BFWD
I
N
B
D
01
FLAP SUPPORT 1
BUSH
LH SHOWN
RH SYMMETRICAL
LOCATION 5
01
ICN-A350-A-57XXP078-A-FAPE3-0726X-A-004-01

### Page 47

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01 Fig.FA Sol.AA SHEET 1/1
REV 00 Dec 15/23 A350-57-P078Flow Chart
Page 47
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS
OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
NOTE:
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
NO
YES
YES
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
YES
CONTACT
AIRBUS
01 FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
FLAP SUPPORT 1 - LOCATION 3, 4, 5
FLAP SUPPORT 2 - LOCATION 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
01
REPEAT THE DETAILED INSPECTION FOR CORROSION
ON THE LH AND RH FLAP SUPPORTS 1 AND 2 WITHIN 
THE REPETITIVE INTERVAL AT LOCATIONS: FLAP SUPPORT 1 - LOCATION 1 AND 2
FLAP SUPPORT 2 - LOCATION 1
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
APPLY REQUIRED SURFACE
PROTECTION AT LOCATIONS:
FLAP SUPPORT 1 - LOCATION 1, 2, 3, 4, 5
FLAP SUPPORT 2 - LOCATION 1, 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
DO A DETAILED INSPECTION FOR CORROSION ON
THE LH AND RH FLAP SUPPORTS 1, 2, 3, AND 4:
NO
ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01

### Page 48

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 48
(3) Task A350-A-57-XX-P078-02001-311A-A (A350-A-57-XX-P078-02ZZZ-311Z-A)
Do a Detailed Inspection of the LH Flap Support 2 - Location 1
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
531
Manpower/Resources/Skills
Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
04DAB2
Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04JME4 T op Coat Polyurethane - -Grey InternalStructure
04QAB2 Coating - - FlexibleStructure
06ACA1
Polysulfide Sealant - Low
Density MultiPurpose
Brushable
06LCB1
Non Hardening Jointing
Putty - Medium T emp. Area
Chromate Free
08BAA9 Non Aqueous Cleaner -General
10ABC1
Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
12AEB1
Corrosion Preventive
Compound - Heavy Duty
Long Durability Hard Film
14SBA1 T extile - Lint free Cotton
Referenced Information
Manuals/Drawings References/Sheets
ASR
A350-A-51-21-11-00ZZZ-660Z-A
A350-A-51-24-XX-01ZZZ-667Z-A
A350-A-51-42-XX-01ZZZ-667Z-A
A350-A-51-75-12-00ZZZ-660Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure

### Page 49

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 49
Ref. Fig.BB Detailed Inspection of Flap Support 2 - Location 1
NOTE: T o aid in the inspection, refer to Ref. Fig.FA Flow Chart.
(a) The Standard Practices given in this procedure are:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 Remove and install fasteners in accordance with Ref. ASR A350-A-51-42-XX-
01ZZZ-667Z-A.
3 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
4 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
5 Repair the paint coating in accordance with Ref. ASR A350-A-51-75-12-
00ZZZ-660Z-A.
6 Repair the protective treatment of metal parts in accordance with Ref. ASR
A350-A-51-21-11-00ZZZ-660Z-A.
7 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
8 T ag all the parts you must remove and retain to make the subsequent
installation easier.
CAUTION: DO NOT REMOVE GROUP 1 AND GROUP 2 BOLTS AT THE SAME
TIME. DAMAGE TO THE COMPONENT CAN OCCUR.
(b) Do a detailed inspection of the LH Flap Support 2, location 1– Lever Bearing
Assembly for Group 1.
1 Remove and retain Nuts, item (25), Washers, item (24), and Bolts, item
(23), from Group 1 fastener locations. Refer to Sheet 02.
3 NUT   Item (25) Retain
6 WASHER   Item (24) Retain
3 BOLT   Item (23) Retain
2 Clean the retained parts, component interfaces, and adjacent area with:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
3 Do a detailed inspection of the bushes interface. Make sure there is no
corrosion or damage to the surface protection, refer to Sheet 02 and Sheet
03.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
4 Apply a surface protection if necessary.

### Page 50

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 50
a If necessary, repair protective treatment on the aluminum structure
with:
  Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
10ABC1  
b If necessary, repair paint coating on the aluminum structure with:
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
and
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4  
c If necessary, apply fillet sealant around the edge of the bushes, refer
to Sheet 03. Use:
  Polysulfide Sealant
- Low Density
MultiPurpose Brushable
06ACA1  
d If necessary, apply protection coating to the exposed fillet sealant,
refer to Sheet 03. Use:
  Coating - - Flexible
Structure
04QAB2  
5 Apply a thin layer of jointing putty on the shafts of the retained Bolts, item
(23), Washers, item (24), and Nuts, item (25). Use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
6 Apply a thin layer of jointing putty between the Washers and the mating
surfaces of the Washer, and aircraft structure under the nut, use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
7 Install Nuts, item (25), Washers, item (24), and Bolts, item (23), refer to
Sheet 02.
3 NUT   Item (25) Retained
6 WASHER   Item (24) Retained
3 BOLT   Item (23) Retained
8 T orque the Nuts between 138.7 and 166.4 Nm (102.30 and 122.73 lb.ft).
9 Apply corrosion prevention compound to the head of the Bolts, Washers,
and Nuts. Use:
  Corrosion Preventive
Compound - Heavy
Duty Long Durability
Hard Film
12AEB1

### Page 51

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 51
CAUTION: DO NOT REMOVE GROUP 1 AND GROUP 2 BOLTS AT THE SAME
TIME. DAMAGE TO THE COMPONENT CAN OCCUR.
(c) Do a detailed inspection of the LH Flap Support 2, location 1– Lever Bearing
Assembly for Group 2.
1 Remove and retain Nuts, item (25), Washers, item (24), and Bolts, item
(23), from Group 2 fastener locations. Refer to Sheet 02.
2 NUT   Item (25) Retain
4 WASHER   Item (24) Retain
2 BOLT   Item (23) Retain
2 Clean the retained parts, component interfaces, and adjacent area with:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
3 Do a detailed inspection of the bushes interface. Make sure there is no
corrosion or damage to the surface protection, refer to Sheet 02 and Sheet
03.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
4 Apply a surface protection if necessary.
a If necessary, repair protective treatment on the aluminum structure
with:
  Surface Pretreatment
- Light Alloys Chemical
Conversion Yellow
10ABC1  
b If necessary, repair paint coating on the aluminum structure with:
  Primer Epoxy Paint -
- Corrosion Inhibiting
Structure
04DAB2  
and
  T op Coat Polyurethane -
- Grey InternalStructure
04JME4  
c If necessary, apply fillet sealant around the edge of the bushes, refer
to Sheet 03. Use:
  Polysulfide Sealant
- Low Density
MultiPurpose Brushable
06ACA1  
d If necessary, apply protection coating to the exposed fillet sealant,
refer to Sheet 03. Use:
  Coating - - Flexible
Structure
04QAB2

### Page 52

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 52
5 Apply a thin layer of jointing putty on the shafts of the retained Bolts, item
(23), Washers, item (24), and Nuts, item (25). Use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
6 Apply a thin layer of jointing putty between the Washers and the mating
surfaces of the Washer, and aircraft structure under the nut, use:
  Non Hardening Jointing
Putty - Medium T emp.
Area Chromate Free
06LCB1  
7 Install Nuts, item (25), Washers, item (24), and Bolts, item (23), refer to
Sheet 02.
2 NUT   Item (25) Retained
4 WASHER   Item (24) Retained
2 BOLT   Item (23) Retained
8 T orque the Nuts between 138.7 and 166.4 Nm (102.30 and 122.73 lb.ft).
9 Apply corrosion prevention compound to the head of the Bolts, Washers,
and Nuts. Use:
  Corrosion Preventive
Compound - Heavy
Duty Long Durability
Hard Film
12AEB1

### Page 53

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-07275-A-002-01 Fig.BB Sol.AA SHEET 1/3
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 2 - Location 1
Page 53
CONF ALL
REAR SPAR
A
Z531
Z631
B
LH
RH
A
LH SHOWN
RH SYMMETRICAL
FLAP SUPPORT 2
ICN-A350-A-57XXP078-A-FAPE3-07275-A-002-01

### Page 54

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-07276-A-003-01 Fig.BB Sol.AA SHEET 2/3
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 2 - Location 1
Page 54
CONF ALL
23
24
24
25
C
03
x5
x5
x5
x5
B
C
LEVER BEARING
ASSEMBLY
01
0201
02
NOTE:
REFER TO SHEET 03 FOR THE APPLICABLE NOTES
A
A
04
06
07
08
0808
08
0108
LH SHOWN
RH SYMMETRICAL
LH SHOWN
RH SYMMETRICAL
FLAP SUPPORT 2
0605
05
05
ICN-A350-A-57XXP078-A-FAPE3-07276-A-003-01

### Page 55

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-07277-A-002-01 Fig.BB Sol.AA SHEET 3/3
REV 00 Dec 15/23 A350-57-P078Detailed Inspection of Flap Support 2 - Location 1
Page 55
CONF ALL
1009
12
11
BUSH
ALUMINUM
STRUCTURE
FILLET SEALANT
TYPICAL VIEW
A A
06
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB1, ON THE SHAFTS04
TORQUE THE NUT TO BETWEEN 138.7 AND 166.4 Nm (102.30 and 122.73 lb.ft)07
08
GROUP 202
NOTE:
GROUP 101
DO NOT REMOVE BOLT WITH ELECTRICAL BONDING03
10
APPLY SURFACE TREATMENT MATERIAL No. 10ABC1 AS NECESSARY09
APPLY COATING MATERIAL No. 04QAB2 TO THE EXPOSED SEALANT12
APPLY FILLET SEALANT MATERIAL No. 06ACA1 AROUND THE EDGE OF THE BUSH AS NECESSARY11
APPLY SURFACE PROTECTION MATERIAL No. 04DAB2 AND 04JME4 ON THE ALUMINUM STRUCTURE
AS NECESSARY
DO A DETAILED INSPECTION AROUND THE BUSH EDGE FOR CORROSION ON THE
ALUMINUM STRUCTURE
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB105
APPLY A THIN LAYER OF JOINTING PUTTY MATERIAL No. 06LCB1, BETWEN THE WASHER AND
STRUCTURE
ICN-A350-A-57XXP078-A-FAPE3-07277-A-002-01

### Page 56

A350
SERVICE BULLETIN
Figure ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01 Fig.FA Sol.AA SHEET 1/1
REV 00 Dec 15/23 A350-57-P078Flow Chart
Page 56
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS
OR COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
NOTE:
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
NO
YES
YES
CONTACT
AIRBUS
IS THERE
CORROSION?
IS THERE
CORROSION?
YES
CONTACT
AIRBUS
01 FOR THE ACCOMPLISHMENT TIMESCALE, REFER TO PARAGRAPH 1.E.(2).
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
FLAP SUPPORT 1 - LOCATION 3, 4, 5
FLAP SUPPORT 2 - LOCATION 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
01
REPEAT THE DETAILED INSPECTION FOR CORROSION
ON THE LH AND RH FLAP SUPPORTS 1 AND 2 WITHIN 
THE REPETITIVE INTERVAL AT LOCATIONS: FLAP SUPPORT 1 - LOCATION 1 AND 2
FLAP SUPPORT 2 - LOCATION 1
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
APPLY REQUIRED SURFACE
PROTECTION AT LOCATIONS:
FLAP SUPPORT 1 - LOCATION 1, 2, 3, 4, 5
FLAP SUPPORT 2 - LOCATION 1, 2, 3, 4
LEVER 2 ON FLAP SUPPORT 2 - LOCATION 1, 2
FLAP SUPPORT 3 - LOCATION 1
FLAP SUPPORT 4 - LOCATION 1
DO A DETAILED INSPECTION FOR CORROSION ON
THE LH AND RH FLAP SUPPORTS 1, 2, 3, AND 4:
NO
ICN-A350-A-57XXP078-A-FAPE3-0726K-A-003-01

### Page 57

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 57
(4) Task A350-A-57-XX-P078-25001-311A-A (A350-A-57-XX-P078-25ZZZ-311Z-A)
Do a Detailed Inspection of the LH Flap Support 2 - Location 2, 3 and 4
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
531
Manpower/Resources/Skills
Man-hours 5.00 h
Minimum Number of person 1
Elapsed Time 5.00 h
Skills Airframe
Material necessary to do the job
Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
03FDB1 Mineral Oil base Grease -Anti-FrettingPaste
04QAB2 Coating - - FlexibleStructure
04SAB2 Varnish Polyurethane - -Marking Structure
06AAC1 Polysulfide Sealant -General Purpose Interfay
06ACB1 Polysulfide Sealant - LowDensity MultiPurpose Fillet
08BAA9 Non Aqueous Cleaner -General
14SBA1 T extile - Lint free Cotton
Part kit 57P078D01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 V5757653420000 1 WASHER
67 V5757632220000 1 WASHER
73 ABS1149AP2500B 1 WASHER
82 MS24665-380 1 PIN
83 MS16624-4143 1 RING
90 MS24665-309 1 PIN
Referenced Information
Manuals/Drawings References/Sheets
ASR A350-A-51-24-XX-01ZZZ-667Z-A
SD A350-A-06-3X-XX-01ZZZ-04CZ-A
CML CONSUMABLE MATERIAL LIST (CML)
Procedure
Ref. Fig.BF Detailed Inspection of Flap Support 2 - Location 2, 3 and 4

### Page 58

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 58
NOTE: T o aid in the inspection, refer to Ref. Fig.FA Flow Chart.
(a) The Standard Practices given in this procedure are:
1 For the identification of zones, refer to Ref. SD A350-A-06-3X-XX-01ZZZ-
04CZ-A.
2 For the specification of Material application codes given in this Service
Bulletin, refer to Ref. CML.
3 Apply sealant in accordance with Ref. ASR A350-A-51-24-XX-01ZZZ-667Z-A.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
5 T ag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a detailed inspection of the LH Flap Support 2, location 2 – Hinge lug on Flap
Support 2. Refer to Sheet 01 and Sheet 02, View C.
WARNING: USE GOGGLES EACH TIME YOU CUT A COTTER PIN. REMOVE
AND DISCARD THE COTTER PIN IMMEDIATELY.
1 Cut, remove and discard the Cotter Pin, item (82).
1 Cotter Pin   Item (82) Discard
2 Remove and discard the Retaining Ring, item (83).
1 Retaining Ring   Item (83) Discard
3 Remove the Locking Cap, item (84), Nut, item (85), and the Washer, item
(86).
1 Locking Cap   Item (84) Retain
1 Nut   Item (85) Retain
1 Washer   Item (86) Retain
4 Remove the Failsafe Bolt, item (70) and the Cap Washer, item (71).
1 Failsafe Bolt   Item (70) Retain
1 Cap Washer   Item (71) Retain
5 Unlock the tabs of the Lockwasher, item (73)
6 Remove the Spanner Nut, item (72).
1 Spanner Nut   Item (72) Discard
7 Remove and discard the Lock Washer, item (73).
1 Lock Washer   Item (73) Discard
8 Remove the Washer, item (69).
1 Washer   Item (69) Retain
9 Unlock the tabs of the Lock Washer, item (67).
10 Remove the Spanner Nut, item (68).
1 Spanner Nut   Item (68) Retain

### Page 59

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 59
11 Remove and discard the Lock Washer, item (67).
1 Lock Washer   Item (67) Discard
12 Remove the Washer, item (66).
1 Washer   Item (66) Retain
13 Clean the inspection area, retained parts and component interfaces. Use:
  T extile - Lint free Cotton14SBA1  
made moist with
  Non Aqueous Cleaner -
General
08BAA9  
14 Do a detailed inspection of the bush interface (without the flange). Make
sure there is no corrosion or damage to the surface protection, refer to
Sheet 02, View C.
a If there is corrosion, contact AIRBUS.
b If there is no corrosion, continue to the next step.
15 Do a visual inspection on the retained parts, component interfaces and the
adjacent area to make sure they are in good condition.
16 Apply a thin layer of anti-fretting paste on the Failsafe Bolt, item (70) and
the Nut, item (85).
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
17 Apply a thin layer of anti-fretting paste on the threads of the Spanner Nuts,
item (68) and item (72).
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
18 Apply a thin layer of anti-fretting paste between the mating surfaces of the
Spanner Nuts, item (68) and the new Lock Washer, item 67.
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
19 Apply a thin layer of anti-fretting paste between the mating surfaces of the
Spanner Nuts, item (72) and the new Lock Washer, item 73.
  Mineral Oil base Grease
- Anti-FrettingPaste
03FDB1  
20 Install the Washer, item (66).
1 Washer   Item (66) Retained
21 Install the new Lock Washer, item 67.
1 WASHER-LOCK V5757632220000 Item 67
22 Install the Spanner Nut, item (68) with space between the Washer, item
(66) and the support lug.
1 Spanner Nut   Item (68) Retained

### Page 60

A350
SERVICE BULLETIN
REV 00 Dec 15/23 A350-57-P078
Page 60
23 Install the Washer, item (69), the new Lock Washer, item 73 and the
Spanner Nut, item (72).
1 Washer   Item (69) Retained
1 WASHER-KEY ABS1149AP2500B Item 73
1 Spanner Nut   Item (72) Retained
24 T orque the Spanner Nut, item (72) to between 120.0 and 135.0 Nm (88.51
and 99.57 lb.ft).
25 Make sure there is a space in between the Washer, item (66) and the
support lug.
26 T urn the Spanner Nut, item (68) outboard until the Washer, item (66)
touches the support lug and apply the initial torque as follows:
a T orque the Spanner Nut, item (68) to between 20.0 and 25.0 Nm
(14.76 and 18.43 lb.ft).
27 Safety the Spanner Nut, item (68) with the new Lock Washer, item 67.
28 Safety the Spanner Nut, item (72) with the new Lock Washer, item 73.
29 Install the Cap Washer, item (71) and the Failsafe Bolt, item (70).
1 Cap Washer   Item (71) Retained
1 Failsafe Bolt   Item (70) Retained
30 Install the Washer, item (86) and the Nut, item (85).
1 Washer   Item (86) Retained
1 Nut   Item (85) Retained
31 T orque the Nut, item (85) to between 80.0 and 90.0 Nm (59.01 and 66.38
lb.ft).
32 Install the Locking Cap, item (84) and the new Retaining Ring, item 83.
1 Locking Cap   Item (84) Retained
1 RING-RETAINING MS16624-4143 Item 83
33 Install the new Cotter Pin, item 82.
1 PIN-COTTER MS24665-380 Item 82
34 Mark a red line across the Nuts, item (68), item (72) and item (85) to the
adjacent structure with:
  Varnish Polyurethane - -
Marking Structure
04SAB2  
NOTE: The line must have an approximate width of 3.5 mm (0.14 in.)
Continue the line across the surface of the adjacent structure to a
distance of approximately 5 mm (0.2 in.).
(c) Do a detailed inspection of the LH Flap Support 2, location 3 – Pivot tube on Flap
Support 2. Refer to Sheet 01 and Sheet 02, View E.
1 Unfold the lugs of the Lock Washer, item (2).

The text continues at https://openairdocs.org/service-documents/airbus/57-p078-00/file/65028aa24166.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
