# Airbus Service Bulletin A300-53-6184

Copy: No revision named ("SB A300-53-6184"), 27 pages: PDF https://openairdocs.org/files/sha256/29/c2/29c28f7462d19ff2e8476033d14ed2035727aaa8d6293aaa019b9e172938ed27; text https://openairdocs.org/service-documents/airbus/a300-53-6184/file/29c28f7462d1.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2016-9051; AD 2017-06-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A300-53-6184
- Page: https://openairdocs.org/service-documents/airbus/a300-53-6184

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2017-06-04](https://openairdocs.org/ad/2017-06-04.md), effective May 1, 2017: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a300-53-6184/proposed.md).

## Text (27 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2016-9051; AD 2017-06-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A300-600
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 53
TITLE: FUSELAGE - REAR FUSELAGE - INSPECT SKIN LAP JOINT BELOW
STGR 28 BETWEEN FR72 AND FR76, LH AND RH.
**CONF ALL
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
During a routine check on an A300 A/C a damage was initially noticed above the right MID
passenger/crew door. After removal of the insulation blankets on the area, a crack was found in the
door surrounding panel.
The crack spread longitudinally from Frame(FR) 29 to FR30 approximately, along the radius of the skin
panel step. It was not visible from the outside of the A/C because it spreads along a line that is always
covered by a sealant bead at the junction of two panels.
A Fatigue and Damage Tolerance (F & DT) analysis was done for the A300-600 A/C fleet for a potential
similar issue.
It was concluded that the same kind of longitudinal crack could develop on this fleet in similar area in
terms of stress loading and design, which are located at joint between FR72 and FR76 described in this
Service Bulletin.
The objective of this Service Bulletin is to provide the necessary instructions, the intervals and the
appropriate actions for the inspection of the affected area on A300-600 aircrafts.
Accomplishment of this Service Bulletin will support detection of possible cracks at an early stage,
which will contribute to avoid any extensive repair and aircraft down time. Undetected cracks could
affect the structural integrity of the area concerned.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 MANDATORY (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 YES
 A/C OPERATION AFFECTED
 NO
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A300-600
SERVICE BULLETIN
SUMMARY
EVALUATION TABLE
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 ETOPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
NOTE
 (1)
: Service Bulletin must be accomplished.
MATERIAL PRICE INFORMATION
No Material
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
67Q ABR AHK BCS FDX IRA IRM KAC MNB MRJ MSR SOP SUD
TAR THA UQA URS UTP
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
Task 536184-832-848-001: Inspection
TOTAL MANHOURS
 6.00
ELAPSED TIME (HOURS)
 5.00
APPENDICES
Appendix 01 - Elapsed Time Assumption
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 2
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A300-600
SERVICE BULLETIN
SUMMARY
**CONF ALL
Z170
A
FR76
FR75A
FR75
FR74
FR73A
FR73A
LH SHOWN
RH SYMMETRICAL FR72
STGR28
STGR29
INSPECTION OF SKIN LAP JOINT
D_SB_536184_6_SAAA_01_01
Figure A-G SAAA - S heet 01
Inspection of the Skin Lap Joint. Affected area
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 3
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A300-600
SERVICE BULLETIN
SUMMARY
This Page Intentionally Left Blank
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 4
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A300-600
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 53
TITLE: FUSELAGE - REAR FUSELAGE - INSPECT SKIN LAP JOINT BELOW
STGR 28 BETWEEN FR72 AND FR76, LH AND RH.
MODIFICATION No.: None
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
(1) Models
B4-603 B4-605R B4-605RF B4-622F B4-622R B4-622RF C4-605R/F C4-620
(2) Effectivity by MSN
0344 0358 0361 0365 0380 0388 0401 0405 0408 0411 0414 0417 0477 0479 0505
0521 0525 0529-0530 0532 0536 0543 0546 0553 0555 0557-0559 0561 0563 0572
0575 0579 0581 0584 0602-0603 0607-0608 0611 0613 0617-0618 0621 0623
0625-0626 0629-0630 0632-0633 0637 0641 0643 0657 0659 0664 0666 0668 0670
0673 0677 0679 0683 0688 0694 0696 0699 0701 0703 0707 0709 0711 0713 0715
0717 0719 0721-0725 0727 0729-0730 0732-0734 0737 0739-0741 0743-0744 0746
0749-0750 0753-0756 0758 0762-0764 0770 0773 0775 0782-0788 0797 0836-0838
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A300-600
SERVICE BULLETIN
OPERATOR
 MSN
67Q
 0584 0603 0744 0749 0764
ABR
 0557 0717 0722
AHK
 0683 0770
BCS
 0529 0602 0617 0621 0637 0641 0670 0677 0679 0703 0711 0724
0729 0730 0737 0740 0743 0753 0783 0797 0836 0837
FDX
 0358 0361 0365 0388 0417 0477 0479 0530 0536 0543 0555 0559
0572 0575 0579 0581 0611 0613 0625 0630 0633 0657 0659 0664
0668 0688 0709 0713 0715
IRA
 0632 0696 0723 0727
IRM
 0380 0401 0405 0408 0411 0414 0546 0553 0608 0618 0623 0701
0773 0838
KAC
 0344 0673 0694 0699 0719 0721
MNB
 0521 0525 0734 0739 0755 0756 0758
MRJ
 0750 0762
MSR
 0561 0607
SOP
 0532
SUD
 0666 0775
TAR
 0505 0558 0563
THA
 0629 0782 0784 0785 0786 0787
UQA
 0626 0643
URS
 0733 0788
UTP
 0707 0725 0732 0741 0746 0754 0763
(4) Configuration by MSN
MSN
 CONFIGURATION
0344 0358 0361 0365 0380 0388 0401 0405 0408 0411 0414
0417 0477 0479 0505 0521 0525 0529 0530 0532 0536 0543
0546 0553 0555 0557 0558 0559 0561 0563 0572 0575 0579
0581 0584 0602 0603 0607 0608 0611 0613 0617 0618 0621
0623 0625 0626 0629 0630 0632 0633 0637 0641 0643 0657
0659 0664 0666 0668 0670 0673 0677 0679 0683 0688 0694
0696 0699 0701 0703 0707 0709 0711 0713 0715 0717 0719
0721 0722 0723 0724 0725 0727 0729 0730 0732 0733 0734
0737 0739 0740 0741 0743 0744 0746 0749 0750 0753 0754
0755 0756 0758 0762 0763 0764 0770 0773 0775 0782 0783
0784 0785 0786 0787 0788 0797 0836 0837 0838
001
(5) Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft given in the effectivity of this Service Bulletin as a
standard configuration.
(6) Material Effectivity
MATERIAL
 QTY PER A/C
 SEE NOTES
Consumable CMLD01
 1
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 2
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A300-600
SERVICE BULLETIN
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
During a routine check on an A300 A/C a damage was initially noticed above the right
MID passenger/crew door. After removal of the insulation blankets on the area, a crack
was found in the door surrounding panel.
The crack spread longitudinally from Frame(FR) 29 to FR30 approximately, along the
radius of the skin panel step. It was not visible from the outside of the A/C because it
spreads along a line that is always covered by a sealant bead at the junction of two
panels.
A Fatigue and Damage Tolerance (F & DT) analysis was done for the A300-600 A/C
fleet for a potential similar issue.
It was concluded that the same kind of longitudinal crack could develop on this fleet in
similar area in terms of stress loading and design, which are located at joint between
FR72 and FR76 described in this Service Bulletin.
(2) Objective/Action
The objective of this Service Bulletin is to provide the necessary instructions, the
intervals and the appropriate actions for the inspection of the affected area on A300-600
aircrafts.
(3) Advantages
Accomplishment of this Service Bulletin will support detection of possible cracks at an
early stage, which will contribute to avoid any extensive repair and aircraft down time.
Undetected cracks could affect the structural integrity of the area concerned.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
Task 536184-832-848-001: Inspection
(1) Inspect the Skin Lap Joint below STGR 28 between FR72 and FR76, LH
(2) Inspect the Skin Lap Joint below STGR 28 between FR72 and FR76, RH
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 3
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A300-600
SERVICE BULLETIN
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an Airworthiness
Directive (AD) published by the European Av iation Safety Agenc y (EASA) will be issued
to confirm this classification. It is anticipated that the AD will confirm the (thresholds
and/or intervals and/or date) given but reference should be made to the AD for
confirmation of the mandated accomplishment timescale.
Table 01, Config 001 - Do a Special Detailed Inspection (SDI) of the skin lap joint below STGR 28
between FR72 and FR76
COMPLIANCE TIME
CONDITION
 ACTION
Threshold
 Grace Period
REPETITIVE
INTERVAL
All aircraft
 Do a Special
Detailed Inspection
(SDI) of skin lap
joint below STGR
28 between FR72
and FR76
29500 FC from the
aircraft Entry In
Service date
2000 FC from AD
effective date
None
No cracks found
 Repeat the
inspection
None
 None
 Within 5400 FC
Crack found
 Contact AIRBUS
and follow their
instructions
Before next flight
 None
 None
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approv al No. EASA. 21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
Task 536184-832-848-001: Inspection
Get Access
 1.50
On Aircraft
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 4
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A300-600
SERVICE BULLETIN
Task 536184-832-848-001: Inspection
Inspect the Skin Lap Joint below STGR 28 between
FR72 and FR76, LH
1.00
Inspect the Skin Lap Joint below STGR 28 between
FR72 and FR76, RH
1.00
Close-Up
 2.50
TOTAL MANHOURS
 6.00
ELAPSED TIME (HOURS)
 5.00
NOTE
: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-GAAAA
 given in Appendix 01.
H. WEIGHT AND BALANCE
Not Changed
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
Aircraft Maintenance Manual (AMM)
 06-21-00 06-31-53 20-21-12
24-00-00 25-22-11 28-26-15
36-12-00 52-34-00 53-17-00
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
Non Destructive Test Manual (NTM)
 53-18-02
Structural Repair Manual (SRM)
 51-21-00 51-23-20
K. PUBLICATION AFFECTED
Non Destructive Test Manual (NTM)
 53-18-02
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 5
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A300-600
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 6
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A300-600
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
None
(2) Price and Availability
None
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
C. LIST OF COMPONENTS
No Kit
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-General
 08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
(2) Components
None
(3) Equipment
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
F. TOOLING
None
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 7
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A300-600
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 8
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A300-600
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 536184-832-848-001 - Inspection
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: USE SOLVENTS/CLEANING AGENTS , SEALANTS AND OTHER SPECIAL
MATERIALS ONLY WITH A GOOD FLOW OF AIR THROUGH THE WORK
AREA. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND
SKIN IRRITANTS. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON
PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT
SMOKE. DO NOT BREATHE THE GAS. GET MEDICAL HELP IF YOUR SKIN OR
EYES BECOME IRRITATED.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
CAUTION
: DO NOT TURN CONTAINERS OR PALLETS WHILE THEY ARE IN THE
CARGO COMPARTMENT. IF YOU TURN CONTAINERS OR PALLETS IN THE
CARGO COMPARTMENT, YOU CAN CAUSE DAMAGE TO LININGS, NETS,
CURTAINS OR TO COMPONENTS OF THE CARGO LOADING SYSTEM.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 9
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A300-600
SERVICE BULLETIN
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: The purpose of flow charts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
Task Associated Data
Zone
170
Access
Door
 162AZ 813
Manpower
TOTAL MANHOURS
 6.00
ELAPSED TIME (HOURS)
 5.00
A. GENERAL
(1) Subtask 536184-910-201-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-31-53, Page Block 001
20-21-12, Page Block 001
53-17-00, Page Block 001
Consumable Material List (CML)
(a) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(b) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(c) For the Stringer (STGR) identification, refer to AMM 53-17-00, Page Block 001.
(d) To torque tighten the electrical component fasteners, refer to AMM 20-21-12, Page
Block 001.
(e) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(f) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
the Consumable Materials List (CML).
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 10
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A300-600
SERVICE BULLETIN
(2) Subtask 536184-839-201-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 536184-941-201-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
25-22-11, Page Block 401
28-26-15, Page Block 401
36-12-00, Page Block 401
52-34-00, Page Block 001
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(b) Put an access platform in position at the Bulk Cargo-Compartment Door RH side.
(c) Put the warning notices in position next to the access platform.
(d) Open the Bulk Cargo-Compartment Access Door 813, refer to AMM 52-34-00,
Page Block 001.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 11
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A300-600
SERVICE BULLETIN
(e) Get into the Bulk Cargo-Compartment, and open the AFT Cabin Underfloor
Compartment Access Door 162AZ.
(f) Access to the AFT Equipment Compartment zone.
(g) Remove the heat and sound insulation from the inspection area as necessary, refer
to AMM 25-22-11, Page Block 401.
(h) If necessary for a good access to RH side work area, remove and retain the APU
Bleed Air Supply ducts next to the inspection area, refer to AMM 36-12-00, Page
Block 401.
(i) If necessary, release the harnesses of the structure and the supports associated
without disconnecting it.
C. PROCEDURE
(1) Subtask 536184-270-201-001 - Inspect the Skin Lap Joint below STGR 28 between
FR72 and FR76, LH
Work Zones and Access Panels
Zone
 Access/Work location
170
 Access
 Door 813, Door 162AZ
Work location
 from Frame 72 to Frame 76
from Stringer 28 to Stringer 29
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 NON DESTRUCTIVE
TESTING
Material necessary to do the job
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Non Destructive Test Manual (NTM)
 53-18-02
Structural Repair Manual (SRM)
 51-21-00
51-23-20
Fig. A-GBAAA
Inspection of the Skin Lap Joint
Sheet 01
Sheet 02
Fig. A-GFAAA
Inspection Flow-Chart
Sheet 01
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 12
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A300-600
SERVICE BULLETIN
References
Fig. A-GRAAA
Report Sheet
Sheet 01
(a) For the Inspection Flowchart, refer to Fig. A-GFAAA Sheet 01
 .
(b) From the aircraft interior, clean the surface of the inspection area shown in Fig. A-
GBAAA Sheet 02
 with:
Textile-Lint Free
Cotton
14SBA1 As required
and
Non Aqueous
Cleaner-General
08BAA9 As required
(c) From the aircraft interior, do a Ultrasonic inspection on the skin lap joint between
STGR 28 and STGR 29 and between Frame 72 and Frame 76.
Refer to NTM 53-18-02.
Refer to Fig. A-GBAAA Sheet 01
 and Fig. A-GBAAA Sheet 02
 for the location of
the inspection area.
(d) Put in common the inspection result with the result of the other aircraft side.
1
 If no crack is found:
a
 Proceed to Close up the work and you must repeat the inspection within
the interval defined in section 1.E.(2) of this Service Bulletin.
2
 If any crack is found:
a
 Contact AIRBUS repair support for further instructions, before next flight.
(e) Apply the special protection which has been removed during the cleaning phase, in
accordance with SRM 51-21-00 and SRM 51-23-20.
(f) Fill in the inspection report with the data from both aircraft sides and send it to
AIRBUS. For the Inspection Report, refer to Fig. A-GRAAA Sheet 01
 .
(2) Subtask 536184-270-202-001 - Inspect the Skin Lap Joint below STGR 28 between
FR72 and FR76, RH
Work Zones and Access Panels
Zone
 Access/Work location
170
 Access
 Door 813, Door 162AZ
Work location
 from Frame 72 to Frame 76
from Stringer 28 to Stringer 29
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 13
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A300-600
SERVICE BULLETIN
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 NON DESTRUCTIVE
TESTING
Material necessary to do the job
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Non Destructive Test Manual (NTM)
 53-18-02
Structural Repair Manual (SRM)
 51-21-00
51-23-20
Fig. A-GBAAA
Inspection of the Skin Lap Joint
Sheet 01
Sheet 02
Fig. A-GFAAA
Inspection Flow-Chart
Sheet 01
Fig. A-GRAAA
Report Sheet
Sheet 01
(a) For the Inspection Flowchart, refer to Fig. A-GFAAA Sheet 01
 .
(b) From the aircraft interior, clean the surface of the inspection area shown in Fig. A-
GBAAA Sheet 02
 with:
Textile-Lint Free
Cotton
14SBA1 As required
and
Non Aqueous
Cleaner-General
08BAA9 As required
(c) From the aircraft interior, do a Ultrasonic inspection on the skin lap joint between
STGR 28 and STGR 29 and between Frame 72 and Frame 76.
Refer to NTM 53-18-02.
Refer to Fig. A-GBAAA Sheet 01
 and Fig. A-GBAAA Sheet 02
 for the location of
the inspection area.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 14
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A300-600
SERVICE BULLETIN
(d) Put in common the inspection result with the result of the other aircraft side.
1
 If no crack is found:
a
 Proceed to Close up the work and you must repeat the inspection within
the interval defined in section 1.E.(2) of this Service Bulletin.
2
 If any crack is found:
a
 Contact AIRBUS repair support for further instructions, before next flight.
(e) Apply the special protection which has been removed during the cleaning phase, in
accordance with SRM 51-21-00 and SRM 51-23-20.
(f) Fill in the inspection report with the data from both aircraft sides and send it to
AIRBUS. For the Inspection Report, refer to Fig. A-GRAAA Sheet 01
 .
D. TEST
None
E. CLOSE-UP
(1) Subtask 536184-942-201-001 - Close-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 25-22-11, Page Block 401
36-12-00, Page Block 401
52-34-00, Page Block 001
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the previously removed heat and sound insulation, refer to AMM 25-22-11,
Page Block 401.
(c) If removed, install the APU Bleed Air Supply ducts next to the inspection area, refer
to AMM 36-12-00, Page Block 401.
(d) If removed, install the harnesses on the structure and the supports associated.
(e) Go to the Bulk Cargo-Compartment and close the AFT Cabin Underfloor
Compartment Access Door 162AZ.
(f) Exit the Bulk Cargo-Compartment and close the Bulk Cargo-Compartment Access
Door 813, refer to AMM 52-34-00, Page Block 001.
(g) Remove the access platform(s).
(h) Remove the warning notices from position.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 15
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A300-600
SERVICE BULLETIN
(i) Put the aircraft back to its initial configuration.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 16
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A300-600
SERVICE BULLETIN
**CONF ALL
FR76
FR75A
FR75
FR74
FR73A
FR73
A
LH SHOWN
RH SYMMETRICAL
FR72B
Z170
A
STGR28
STGR29
D_SB_536184_6_BAAA_01_01
Figure A-G BAAA - S heet 01
Inspection of the Skin Lap Joint
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 17
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A300-600
SERVICE BULLETIN
**CONF ALL
C
A
A
10 mm
(0.394 in)
5 mm
(0.197 in)
B
A A C
NOTE:
INSPECTION AREA
INBD
FR76
FR75A
FR75
FR74
FR73A
FR73
FR72
STGR28
SECTION OF THE
INSPECTION AREA
STGR29
STGR28
STGR29
D_SB_536184_6_BAAA_02_01
Figure A-G BAAA - S heet 02
Inspection of the Skin Lap Joint
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 18
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A300-600
SERVICE BULLETIN
**CONF ALL
PERFORM ULTRASONIC INSPECTION OF
SKIN LAP JOINT BELOW STR28,
BETWEEN FR72 AND FR76 ON LH AND RH SIDE
NOTE:
FOUND? NOYES CRACK
CONTACT AIRBUS DO THE CLOSE UP OF
THE WORK
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE IMFORMATION GIVEN IN THE PROCEDURE
AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
WITHIN 29500 FC FROM AIRCRAFT ENTRY
INTO SERVICE DATE (WITH A GRACE PERIOD
OF 2000 FC FROM AD EFFECTIVE DATE)
AND FOLLOW THEIR INSTRUCTIONS
WITHIN 5400 FC
ANY
D_SB_536184_6_FAAA_01_01
Figure A-GFAAA - Sheet 01
Inspection Flow-Chart
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 19
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A300-600
SERVICE BULLETIN
**CONF ALL
INSPECTION REPORT
SERVICE BULLETIN No. :
A/C MSN :
FLIGHT CYCLES :
FLIGHT HOURS :
A300−53−6184
DATE OF INSPECTION :
INSPECTION METHOD : SPECIAL DETAILED
INSPECTION
RETURN TO :
AIRBUS
CUSTOMER SERVICES ENGINEERING
DOORS − FUSELAGE − CWB − WINDOWS
1 ROND POINT MAURICE BELLONTE
31707 BLAGNAC CEDEX
FRANCE
E−mail: inspection.results@airbus.com
FAX +33 (0)5 61 93 36 14
INSPECTION OF SKIN LAP JOINT BELOW STGR 28, BETWEEN FR72 AND FR76 LH AND RH
LH RH
NUMBER OF CRACKS
ACCUMULATED
CRACK LENGTH NUMBER OF CRACKS
ACCUMULATED
CRACK LENGTH
RESULT :
AREA REPAIRED IN ACCORDANCE WITH :
PLEASE GIVE DETAILS OF ANY OTHER FINDINGS :
REMARKS :
D_SB_536184_6_RAAA_01_00
Figure A-GRAAA - Sheet 01
Report Sheet
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 20
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A300-600
SERVICE BULLETIN
Appendix 01 - Elapsed Time Assumption
**CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A300−53−6184
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
6.00
5.00
STEPS
0
GET ACCESS 1.50 1.50
INSPECTION OF SKIN LAP 1.00 1.00
CLOSE−UP 2.50 2.50
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTE:
PER
1
1
1
1.00 1.00 1
:
:
SB ELAPSED TIME
(HOURS)
1 2 3 4
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
JOINT LH
INSPECTION OF SKIN LAP
JOINT RH
5
D_SB_536184_6_AAAA_01_01
Figure A-G AAAA - S heet 01
Gantt Chart
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A300-600
SERVICE BULLETIN
REPORTING SHEET
TITLE: FUSELAGE - REAR FUSELAGE - INSPECT SKIN LAP JOINT BELOW
STGR 28 BETWEEN FR72 AND FR76, LH AND RH.
MODIFICATION No.: None
Please complete the appropriate item (A or B):
A - SB WILL BE
 embodied YES/NO (if NO please comment)
If YES, aircraft concer ned (as per SB effectivity by default) and planned dates (month/year) of
embodiment:
B - SB HAS BEEN
 embodied on aircraft:
Operator comments:
From Airline:
Name/Title:
Signature: Date:
If operational documentation is affected (see Paragraph 1.K of this SB): If information is needed prior to
next normal revision or prior to SB embodiment, please indicate required service(s):
Either: Modification Operational Impact (MOI), if available YES/NO
Or : Intermediate revision YES/NO
Important Information:
 This SB will only be incorporated in your maintenance and operational
documentation if this sheet is returned to Airbus and signed by a duly authorised representative. With
the next feasible revision, this will result in
- Updating of maintenance documentation to show pre and post SB data.
- Updating of maintenance and operational documentation to show post SB data after embodiment.
If this SB requires previous or simultaneous accomplishment of other SBs, Airbus shall automatically
include them in the manual revisions. Refer to SIL 00-037 for detailed information.
Please return this completed sheet to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Attn: SDC32 Technical Data and Documentation Services
F A X :( + 3 3 )56 19 32 80 6
e-mail: sb.reporting@airbus.com
or via your Resident Customer Support Office.
Alternatively, SB lists via letters or fax are also accepted.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A300-600
SERVICE BULLETIN
QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.
(Please rate on a scale of 1 to 4, with 4 being the highest score)
- Quality rating of this SB 4321
- Quality rating of the Accomplishment Instructions 4321
- Quality rating of the Illustrations 4321
- Is this SB easy to understand ? Y/N
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.
Planning Material Instructions
X Effectivity X Kit content X Preparation
X Reason X List of Materials Operator Supplied X Mod/Inspection
X Manpower X Industry support X Test
X References X Re-identification X Close-Up
X Publication X Tooling X Illustrations
Comments:
Operator: Date:
Name/Title:
Please return this form to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Attn : SEM4 Service Bulletins Management
F A X:( 3 3 )56 19 34 25 1
Or via your Resident Customer Support Office.
DATE: Nov 12/15 SERVICE BULLETIN No.: A300-53-6184
REVISION No.: 00 - Nov 12/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
