# Airbus Service Bulletin A300-54-6031

Copy: No revision named ("U.S. DOT/FAA - Service Bulletin - A300-54-6031 Revision 00"), 24 pages: PDF https://openairdocs.org/files/sha256/45/41/4541f18d1ebb6bd4931077c8075132a3e662293cdc1f06855b0a18e1837cb7bc; text https://openairdocs.org/service-documents/airbus/a300-54-6031/file/4541f18d1ebb.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0230; AD 2015-02-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A300-54-6031
- Page: https://openairdocs.org/service-documents/airbus/a300-54-6031

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-02-03](https://openairdocs.org/ad/2015-02-03.md), effective Mar 5, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a300-54-6031/proposed.md).

## Text (24 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2014-0230; AD 2015-02-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

AIRBUS INDUSTRIE  CUSTOMER SERVICES DIRECTORATE  • A300-600
1 Rond Point Maurice BELLONTE
31707 BLAGNAC CEDEX FRANCE  SERVICE BULLETIN
Tel: (33) 61-93-33-33
Telex : AIRBU 530526 F
This summary is for information only and is not approved for
modification on the aircraft.
TITLE : NACELLES/PYLONS - MODIFY RIB 5 IN THE PYLON BOX (RETROFIT
SOLUTION).
MODIFICATION No. 11109S20987  ATA SYSTEM : 54
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Two operators of A300 A/C fitted with GE engine pylons have reported
cracks on the lower side of rib 5 in the pylon box. The concerned area
is similar on A300/600 A/C fitted with GE engine pylons. The cracks were
encountered on aircraft which have logged between 16,000 and
27,000 flight hours approximately.
Investigations disclosed that these cracks are due to the stresses
resulting from the pressure applied by the thrust reverser cowl bumpers-
This Service Bulletin recommends the replacement of the stiffeners made
out of bent extrusion by new thicker machined stiffeners.
Accomplishment of this Service Bulletin is recommended on GE CF6-80C
pylons at 15,000 flight hours, or at the next C-check for aircraft
having reached 15,000 flight hours.
Accomplishment of this Service Bulletin cancels requirements of
Inspection Service Bulletin No. A300-54-6034.
EFFECTIVITY
This Service Bulletin is applicable to the following customer (s) : AAL,
CCA, CNW, DLH, FDX, IRA, KAC, MON, OAL, THA, UAE, XF and XO.
SERVICE BULLETIN TO BE ACCOMPLISHED PREVIOUSLY OR SIMULTANEOUSLY
None.
5 DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 1 of 4
Printed in France

### Page 2 (OCR)

G A300-600
SERVICE BULLETIN
SUMMARY
REFERENCES/REPERCUSSIONS
TFU  : 54-51-16-001
OEB  : None
AOT  : None
SIL  : None
LIFE LIMIT  : None
LINE MAINTENANCE AFFECTED : NO
OTHER  : None
AIRCRAFT :  YES
EQUIPMENT :  NO
HARD :  NO
SOFT :  NO
OBRM :  NO
COMPLIANCE
Recommended.
MANPOWER
Per pylon
TOTAL MANHOURS  32-0
ELAPSED TIME (HOURS)  26.0
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 2
Printed in France

### Page 3 (OCR)

© A300-600
SERVICE BULLETIN
SUMMARY
MATERIAL INFORMATION
AIRCRAFT DATA
Qty per engine pylon :
3 fittings.
EQUIPMENT DATA
None.
APPENDICES
None.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 3
Printed in France

### Page 4 (OCR)

• A300-600
SERVICE BULLETIN
SUMMARY
GE PYLON
RIBS
ASBS B46031 SU 00
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 4
Printed in France

### Page 5 (OCR)

CUSTOMER SERVICES DIRECTORATE  AIRBUS INDUSTRIE  S A300-600
1 Rond Point Maurice BELLONTE
31707 BLAGNAC CEDEX FRANCE  SERVICE BULLETIN
Tel: (33) 61-93-33-33
Telex : AIRBU 530526 F
TITLE : NACELLES/PYLONS - MODIFY RIB 5 IN THE PYLON BOX (RETROFIT
SOLUTION).
MODIFICATION No. 11109S20987  ATA SYSTEM : 54
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Aircraft models : B4-601, B4-603, B4-605R, F4-605R.
(2) Aircraft
Customer and  MSN  Kit No.  Qty
Fleet No.  546031  of Kits
AAL050-084  423,458,460,420,461,462  A01  70
463,465,466,469,470,471
474,506,507,508,509,510
511,512,513,514,515,516
517,606,610,612,615,619
626,639,643,645,675
CCA601-607  521,525,532,707,732,746  A01  14
754
651-653  709,713,715  A01  06
CNW001-003  725,741,763  A01  06
DLH601-611  380,391,401,405,408,411  A01  22
414,546,553,618,623
FDX650-661  726,728,735,736,738,742  A01  24
745,748,752,757,759,760
663-665  766,768,769  A01  06
667-669  771,772,774  A01  06
IRA601,602  723,727  A01  04
KAC601-605  673,694,699,719,721  A01  10
MON001-004  540,556,604,605  A01  08
OAL001,002  632,696  A01  04
5 DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 1 of 23
Printed in France

### Page 6 (OCR)

$ A300-600
SERVICE BULLETIN
Customer and  MSN  Kit No.  Qty
Fleet No.  546031  of Kits
THA051-058  368,371,377,384,395,398  A01  16
464,518
UAE 101-105  505,558,563,608,701  A01  10
151  747  A01  02
XF 501  744  A01  02
503,504  749,764  A01  04
xo 001,002  584,603  A01  04
This modification (Retrofit Solution) is applicable by Service
Bulletin only.
The modification No. 11110S20983 (Production Solution) is embodied
before delivery on A/C MSN 761, 767, 773, 775 and subsequent.
NOTE 1 : This Service Bulletin is applicable on aircraft equipped
with GEE and GEG engines.
NOTE 2 : Modification of one aircraft requires 2 Kits 546031A01.
(3) Spares
None.
B. REASON
(1)  History
Two operators of A300 A/C fitted with GE engine pylons have
reported cracks on the lower side of rib 5 in the pylon box. The
concerned area is similar on A300/600 A/C fitted with GE engine
pylons. The cracks were encountered on aircraft which have logged
between 16,000 and 27,000 flight hours approximately.
Investigations disclosed that these cracks are due to the stresses
resulting from the pressure applied by the thrust reverser cowl
bumpers.
(2) Objective/Action
This Service Bulletin recommends the replacement of the stiffeners
made out of bent extrusion by new thicker machined stiffeners.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 2
Printed in France

### Page 7 (OCR)

© A300-600
SERVICE BULLETIN
(3) Advantages
The replacement of the stiffeners cancels requirements of
Inspection Service Bulletin No. A300-54-6034.
(4) Operational/Maintenance Consequences
None -
(5) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended on
GE CF6-80C pylons at 15,000 flight hours.
C. DESCRIPTION
To accomplish this Service Bulletin, it is necessary to :
on the two pylons, in zones 415-416 (left pylon) and 425-426
(right pylon)
(1) Gain access to the working area.
(2) Remove the ventilation duct between rib 2 and rib 7.
(3) Lift the external mating strips between rib 3 and rib 5.
(4) Remove the fittings and the shims at rib 5.
(5) Install. the fitting and the shim at rib 5, left side.
(6) Install the fitting and the shim at rib 5, right side.
(7) Install the external mating strips between rib 3 and rib 5.
(8) Install the ventilation duct between rib 2 and rib 7.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION NO. :  PAGE : 3
Printed in France

### Page 8 (OCR)

© A300-600
SERVICE BULLETIN
D. APPROVAL
The design data contained in this Service Bulletin has been approved
under the authority of DGAC Design Organisation Approval No. C 01.
The changes specified in this Service Bulletin have been approved by the
DGAC when they are major, or under the authority of DGAC Design
Organisation Approval No. C 01, when they are minor.
E. MANPOWER
This Service Bulletin is written for an aircraft in a maintenance
condition. The manhours/elapsed time estimates do not include the time
to prepare for the modification, non-productive elapsed time or
administration.
Kit No. 546031A01 is valid for one pylon.
Gain access  5-0
Remove/install the thrust reverser cowls  6_0
Remove/install the ventilation duct  2.5
Lift/install the mating strips  4.0
Remove the fittings and the shims  3.5
Install the fitting and the shims  6.0
Tests  1-0
Close-up  4-0
TOTAL MANHOURS  32-0
ELAPSED TIME (HOURS)  26-0
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 4
Printed in France

### Page 9 (OCR)

G A300-600
SERVICE BULLETIN
F. MATERIAL - COST AND AVAILABILITY
(1) Material
Customers with aircraft shown in paragraph 1.A.(2) should send a
purchase order to Airbus Industrie. Quote the number of this
Service Bulletin. The address is :
AIRBUS INDUSTRIE
MATERIEL SUPPORT CENTER
P.0. BOX 63 02 62
22312 HAMBURG
GERMANY
(2) Cost and availability
Kit No.  Cost  Availability: Calendar
(US Dollars)  days from receipt of order
546031A01  2450  150
NOTE : The sales terms (costs and availability) are estimated in
relation to economic conditions at the issue date of the
Service Bulletin.
G. TOOLING - PRICE AND AVAILABILITY
Accomplishment of this Service Bulletin entails use of tools described
in AMM 71-13-03, P. Block 401.
H. WEIGHT AND BALANCE
Manufacturers Empty Weight: + 0.832 kg (+ 1.834 Lb)
Effect on balance  : + 22.107 kgm (+ 159.899 Lb.ft)
1. REFERENCES
Aircraft Maintenance Manual (AMM) : 06-41-54, 20-21-12, 24-00-00,
24-41-00, 36-11-00, 36-11-15,
71-13-03
Structural Repair Manual (SRM)  : 51-40-21, 51-40-44, 51-40-47
Consumable Material List (CML)
Service Bulletin  : A300-54-6034
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 5
Printed in France

### Page 10 (OCR)

© A300-600
SERVICE BULLETIN
Structural Repair Manual (SRM) : 54-51-16
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 6
Printed in France

### Page 11 (OCR)

• A300-600
SERVICE BULLETIN
2. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL
(1) Preparation
(a) De-energize the aircraft electrical circuits
(Refer to AMM 24-41-00, P. Block 301).
(b) Electrically ground the aircraft (Refer to AMM 24-00-00,
P. Block 301).
(c) Put the access platforms in position to get access to the
engine pylons.
(d) Remove the access doors 413BL, 415AL, 416AR (left pylon) and
access doors 423BL, 425AL, 426AR (right pylon) (Refer
to AMM 06-41-54).
(e) Remove the thrust reverser cowls (Refer to AMM 71-13-03,
P. B(ock 401).
(f) Remove the bleed air precooler (Refer to AMM 36-11-15,
P. Block 401).
(g) Remove the bleed air precooler cold air inlet duct
(Refer to AMM 36-11-00, P. Block 401).
(2) Standard Practices
(a) To clean the surfaces to be sealed with Methyl-Ethyl-Ketone,
Mat. No. 11-003 (Refer to CML).
(b) To torque standard threaded fasteners (Refer to AMM 20-21-12).
(c) To remove and install the fasteners (Refer to SRM 51-40-21).
(d) To drill and deburr holes (Refer to SRM 51-40-44).
(e) To countersink the holes (Refer to SRM 51-40-47).
(f) To shorten the rivets as required.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 7
Printed in France

### Page 12 (OCR)

G A300-600
SERVICE BULLETIN
B. MODIFICATION
On-the two pylons, in zones 415-416 (Left pylon) and 425-426 (right
pylon), reinforce the fittings at rib 5.
NOTE: The description is given for the left engine pylon. The procedure
is the same for right engine pylon.
(1) Remove the ventilation duct between rib 2 and rib 7.
Refer to Figure 1
(a) Remove :
2 screws  Item (20) (retain)
2 washers  Item (10) (discard)
2 clamps  Item (21) (retain)
1 duct  Item (22) (retain)
(2) Lift the external mating strips between rib 3 and rib 5.
Refer to Figure 2
(a) From the outside of the pylon, Lift:
1 + 1 mating strip  Item (16)
To do this, remove :
2 + 2 rivets  Item (14) (discard)
18 + 18 rivets  Item (15) (discard)
NOTE 1: It is necessary to lift the mating strips to make it
possible to remove the two upper fasteners of fittings
Items 2 and 3 and to countersink these holes.
Remove more rivets, if necessary to prevent damage of
the part.
NOTE 2 : Install wedges to keep the mating strips lifted.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION NO. :  PAGE : 8
Printed in France

### Page 13 (OCR)

A300-600
SERVICE BULLETIN
(3) Remove the fittings and the shims at rib 5.
Refer to Figure 3
(a) From the outside of the pylon, remove :
1 + 1 shim  Item  (23)  (retain)
2 + 2 screws  Item  (24)  (retain)
1 + 1 screw  Item  (25)  (retain)
1 screw, L side  Item  (26)  (retain)
1 screw, R side  Item  (7)  (discard)
2 + 2 washers  Item  (27)  (retain)
1 + 1 washer.  Item  (28)  (retain)
1 washer, L side  Item  (28)  (retain)
1 washer, R side  Item  (11)  (discard)
2 + 2 nuts  Item  (8) (discard)
1 + 1 nut  Item  (13) (discard)
1 nut, L side  Item (13) (discard)
1 nut, R side  Item  (9) (discard)
(b) From the inside of the pylon, remove :
1 fitting  Item  (1) (discard)
1 fitting  Item  (2) (discard)
1 fitting  Item  (3) (discard)
15 rivets  Item (12) (discard)
22 rivets  Item  (5) (discard)
17 screws  Item  (6) (discard)
17 washers  Item  (29) (discard)
17 nuts  Item  (8) (discard)
1 screw  Item  (7) (discard)
1 washer  Item (11) (discard)
1 nut  Item  (9) (discard)
NOTE: Be careful when you remove the rivets Item (12), not to  Nore : go soretut when ye
damage the rivet holes as rivets of the same dimension
will be installed.
(4) Install the fitting and the shim on the left side of the pylon at
rib 5.
Refer to Figure 4
(a) From the inside of the pylon at rib 5, on the lateral panel and
in tront of the stiffener, put in position and temporarily
attach :
1 fitting A5461277820000  Item 3
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 9
Printed in France

### Page 14 (OCR)

• A300-600
SERVICE BULLETIN
(b) Drill the fitting Item 3 to match the holes in the lateral
panel.
Use the table given in Figure 4 and countersink the holes as
written in Para. 2.A. (2) (e).
(c) Clean the drilled area.
(d) Attach the fitting Item 3 with :
& screws  NAS1153E3  Item 16
3 screws  NAS1153E4  Item 5
11 nuts  NAS1726C3E  Item 8
(e) Drill the fitting Item 3 to match the holes in the stiffener.
Use the table given in Figure 4.
(f) Produce a 0.3 mm (0.0118 in.) to 0.5 mm (0.0197 in.) chamfer at
45° on the holes.
(g) Clean the drilled area.
(h) Attach the fitting Item 3 with :
17 screws  NAS6703U3X  Item 6
17 nuts  NAS1726C3E  Item 8
(i) From the outside of the pylon at rib 5, on the lateral panel,
put in position and attach :
1 shim  Item (23)
2 screws  Item (24)
1 screw  Item (25)
1 screw  Item (26)
2 washers  Item (27)
2 washers  Item (28)
2 nuts  NAS1726C3E  Item  8
2 nuts  ASNA2021C4E  Item 13
NOTE : Items (23), (24), (25), (26), (27) and (28) were
retained at removal.
(5)  Install the fittings and the shim on the right side of the pylon at
rib 5.
Refer to Figure 5
(a) From the inside of the pylon at rib 5, on the lateral panel, in
front of the upper stiffener, put in position and temporarily
attach :
1 fitting A5461277620000  Item 2
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION NO. :  PAGE : 10
Printed in France

### Page 15 (OCR)

• A300-600
SERVICE BULLETIN
(b) Drill the fitting Item 2 to match the holes in the lateral
panel.
Use the table given in Figure 5 and countersink the holes as
written in Para. 2.A. (2) (e).
(c) Clean the drilled area.
(d) Attach the fitting Item 2 with :
11 screws NAS1153E4  Item 5
11 nuts  NAS 1726C3E  Item 8
(e) Drill the fitting Item 2 to match the holes in the upper
stiffener.
Use the table given in Figure 5.
(f) Clean the drilled area.
(g) Attach the fitting Item 2 with :
5 rivets NSA5415-40-11  Item 12
in from the inside, on the lateral panel, behind the lower
stiffener and the fitting Item 2, put in position and
temporarily attach :
1 fitting A5461277220000  Item 1
(i) Drill the fitting Item 1 to match the holes in the lateral
panel and in the lower stiffener.
Use the table given in Figure 5.
(j) Clean the drilled area.
(k) Attach the fitting Item 1 with :
5 screws  NAS6703U4  Item  4
1 screw  NAS6704U15X  Item
5 washers  NSA5379-3C  Item 10
1 washer  ASNA2394EW4  Item 11
5 nuts  NAS1726C3E  Item 8
1 nut  NAS1727C4E  Item 9
(L) Drill the fitting Item 1 to match the hole in the fitting
Item 2 and drill the fitting Item 2 to match the holes in the
fitting Item 1.
Use the table given in Figure 5.
(m) Clean the drilled area.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 11
Printed in France

### Page 16 (OCR)

• A300-600
SERVICE BULLETIN
(n) Attach the fittings Items 1 and 2 with :
5 rivets NSA5415-40-11  Item 12
(o) From the outside of the pylon at rib 5, on the lateral panel,
put in position and attach :
1 shim  Item (23)
¿ screws  Item (24)
1 screw  Item (25)
1 screw  NAS6707U15X  Item
2 washers  Item (27)
1 washer  Item (28)
1 washer  ASNA2394EW4  Item  11
2 nuts  NAS1726C3E  Item
1 nut  ASNA2021C4E  Item  13
1 nut  NAS1727C4E  Item
NOTE : Items (23), (24), (25), (27) and (28) were retained at
removal.
(6) Install the external mating strips between rib 3 and rib 5.
Refer to Figure 2
(a) From the outside of the pylon, drill the mating strips
Item (16) and the lateral panels.
Use the table given in Figure 2.
(b) Countersink the holes as written in Para. 2.A. (2) (e).
(c) Attach the mating strips Item (16) with :
2 + 2 rivets NSA5414-48-11  Item 14
18 + 18 rivets  NSA5414-32-07  Item 15
(7) Install the ventilation duct between rib 2 and rib 7.
Refer to Figure 1
(a) Install :
2 screws  Item (20)
2 washers  NSA5379-3C  Item 10
2 clamps  Item (21)
1 duct  Item (22)
NOTE : Items (20), (21) and (22) were retained at removal.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 12
Printed in France

### Page 17 (OCR)

• A300-600
SERVICE BULLETIN
C. TESTS
(1) Preparation for the tests
(a) Install the bleed air precooler cold air inlet duct
(Refer to AMM 36-11-00, P. Block 401).
(b) Install the bleed air precooler (Refer to AMM 36-11-15,
P. B(ock 401).
(c) Install the thrust reverser cowls (Refer to AMM 71-13-03,
P. Block 301).
(d) Disconnect the aircraft electrical ground connection
(Refer to AMM 24-00-00, P. Block 301) and energize the aircraft
electrical circuits (Refer to AMM 24-41-00, P. Block 301).
(2) Tests
(a) Do the leakage check of the pneumatic duct and precooler
connections (Refer to AMM 36-11-00, P. Block 601).
(b) Do the adjustment/test of the thrust reverser cowl (Refer to
AMM 71-13-03, P. BLock 501).
D. CLOSE-UP
(1) Make sure that the work areas are clean and clear of tools and
other items of equipment.
Install the access doors 413BL, 415AL, 416AR (left pylon) and the
access doors 423BL, 425AL, 426AR (right pylon) (Refer to
AMM 06-41-54).
(3) Remove the access platform(s).
E. DOCUMENTATION
Write in the applicable aircraft records that you have done all the work
given in this Service Bulletin.
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 13
Printed in France

### Page 18 (OCR)

S A300-600
SERVICE BULLETIN
GE PYLON
(20)
(21)  (10) 10
(22)
~
ASB5 546031 AB 00  LEFT SIDE SHOWN
RIGHT SIDE IDENTICAL
Removal/Installation of the Ventilation Duct between Rib 2 and Rib 7
Figure 1
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 14
Printed in France

### Page 19 (OCR)

G A300-600
SERVICE BULLETIN
HOLE DIA
IO  NEW
MIN  FASTENER
ITEM
in.  mm
).193  4.85  0.191  14  NSA 5414-48-110
0.130  3.25  0.128  15  NSA 5414-32-070
+  FASTENERS NOT AFFECTED
HEAD ON THE VISIBLE FACE
(16)
LEFT SIDE SHOWN
RIGHT SIDE SYMMETRICA
NOTE: IF NECESSARY REMOVE MORE RIVETS
Lifting/Installation of the External Mating Strips
between Rib 3 and Rib 5
Figure 2
DATE: May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 15-16
Printed in France

### Page 20 (OCR)

• A300-600
SERVICE BULLETIN
BEFORE  DI
RIGHT SIDE SHOWN
VIEW LOOKING OUTSIDE
(24)  (23)  (23)
OLD ITEM  (27)
(8)
(1)
(6)- (29) - (8)
(25)
(28)  (26)
(13)  (13)  (28)  ses
OLD
ITEM  RIVETS REMOVED  +  EXISTING RIVETS
LEFT PYLON SHOWN  RIGHT PYLON IDENTICAL  (12)  R8/4.0
(5)  REF 40  HEAD ON THE HIDDEN FACE
Removal of the Fittings and the Shims at Rib 5
Figure 3
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 17-18

### Page 21 (OCR)

• A300-600
SERVICE BULLETIN
GE PYLON
SECTION CC
CHAMFER
ÇA
+  FASTENERS NOT AFFECTED
ŤF  HEAD ON THE HIDDEN FACE
HEAD ON THE VISIBLE FACE
mroz  HOLE DIA  mrOI  NEW  NEW
MAX  MIN  ITEM  FASTENER  ITEM  NUT  •(23)-
mm  in.
*=  4.83  0.190  4.81  0.189  5  NAS 1153E4  NAS 1726C3E  (25)
(28)
5.18  0.204  5.16  0.203  6  NAS 6703U3X  NAS 1726C3E
4.83  0.190  4.81  0.189  16  NAS 1153E3  NAS 1726C3E  OWER SPAR DATUM  (26)  (28)
RIBS  13
EFT PYLON SHOW
IGHT PYLON IDENTICA!  RIBS LEET SIDE VIEW LOOKING OUTSIDE  RIBS LEFT SIDE VIEW LOOKING FORWARD
Installation of the Fitting and the Shim at Rib 5
Left side
Figure 4
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 19-20
Printed in France

### Page 22 (OCR)

• A300-600
SERVICE BULLETIN
RIB5
VIEW LOOKING FORWARD  VIEW LOOKING OUTSIDE
RIGHT SIDE
UPPER SPAR DATU  R SPAR DATUM
SECTION CC  UPPFENER
(24)  (23)
(27)
HEAD ON THE VISIBLE FACE
HEAD ON THE HIDDEN FACE
MrOI  HOLE DIA  MIN  mrOI  NEW  FASTENER
ITEM
4.10  0.161  0.159  •  12  NSA5415-10-110  ITEM  NEW  NUT
4,83  0.190  0.189  5  NAS 1153E4  NAS 1726C3E  WASHER
4.82  0.190  4.80  0.189  4  NAS 6703U4  NAS 1726C3E  NSA 5779-3C
6.70  0.264  6.68  0.263  NAS 6704U15X  9  NAS 1727C4E  SNA 2394EW4
LEFT PYLON SHOWN
RIGHT PYLON IDENTICAL
InstalLation of the Fitting and the Shim at Rib 5
Right side
Figure 5
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 21-22
Printed in France

### Page 23 (OCR)

S A300-600
SERVICE BULLETIN
3. MATERIAL INFORMATION
A. LIST OF COMPONENTS
ITEM NEW PART No.  QTY KEYWORD  ITEM  OLD PART No.  INT INST
DISP
Kit No. 546031A01
1  2  A5461277620000  A5461277220000  1  Fitting  Fitting  (2)  (1)  A5461100521000  A5461176950200  *
3  A5461277820000  1  Fitting  (3)  A5461176950000  *
4  NAS6703U4  5  Screw
5  NAS1153E4  14  Screw
NAS6703U3X  17  Screw
NAS6704U15X  2  Screw
8  NAS1726C3E  48  Nut
9  NAS1727C4E  2  Nut
10  NSA5379-3C  7  washer
11  ASNA2394EW4  Washer
12  NSA5415-40-11  10  Rivet
13  ASNA2021C4E  3  Nut
14  NSA5414-48-11  4  Rivet
15  NSA5414-32-07  36  Rivet
16  NAS1153E3  8  Screw
NOTE * : Discard
B. SPECIAL TOOLS
None.
C. LIST OF MATERIALS - OPERATOR SUPPLIED
DESCRIPTION  REFERENCE TO CML  QTY PER A/C
MethyL-EthyL-Ketone  Mat. No. 11-003  As required
D. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None -
DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 23
Printed in France

### Page 24 (OCR)

AIRBUS INDUSTRIE
CUSTOMER SERVICES DIRECTORATE  • A300-600
1 Rond Point Maurice BELLONTE
31707 BLAGNAC CEDEX FRANCE  SERVICE BULLETIN
Tel: (33) 61-93-33-33
Telex : AIRBU 530526 F
TITLE : NACELLES/PYLONS - MODIFY RIB 5 IN THE PYLON BOX (RETROFIT
SOLUTION).
MODIFICATION No. 11109S20987  ATA SYSTEM : 54
IS BEING HEREWITH SUBMITTED TO YOU FOR REVIEW
Please filL :  .. REJECTED
.. WILL BE EMBODIED
.. EFFECTIVITY
This SB can only be incorporated in your "customized" documentation within
the agreed time schedule if this sheet is returned to us on purchase date
and signed by a duly authorized and empowered officer or representative.
FROM :  Please return to :
AIRBUS INDUSTRIE
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice BELLONTE
31707 BLAGNAC CEDEX FRANCE
Tel: (33) 61-93-33-33
Telex : AIRBU 530526 F
- 19..
5 DATE : May 30/96  SERVICE BULLETIN No. : A300-54-6031
REVISION No. :  PAGE : 1 of 1
Printed in France

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
