# Airbus Service Bulletin A300-56-0014

Copy: No revision named ("SB A300-56-0014"), 177 pages: PDF https://openairdocs.org/files/sha256/85/67/8567b26b5b3876622b297e3f5e364d148c9ac197666f8faaa512df2797b0807d; text https://openairdocs.org/service-documents/airbus/a300-56-0014/file/8567b26b5b38.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-1237, the docket of AD 2022-25-08. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A300-56-0014
- Page: https://openairdocs.org/service-documents/airbus/a300-56-0014

## Text (177 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2022-1237, the docket of AD 2022-25-08. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 1
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 56
TITLE: WINDOWS - FIXED WINDOWS - INSPECTION OF SAINT-GOBAIN SULLY
FRONT WINDSHIELD
MODIFICATION No.:
None

### Page 2

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 2
ATA SYSTEM: 56
TITLE: WINDOWS - FIXED WINDOWS - INSPECTION OF SAINT-GOBAIN SULLY
FRONT WINDSHIELD
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR None
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
B. REASON
(1) History
AIRBUS received a report on an in-service event on A319 aircraft about the loss of the
RH side windshield in flight, during the cruise phase. The windshield was the original
from delivery, manufactured by SAINT-GOBAIN SULLY SAS (SGS). The investigation
of the A319 event determined that both structural plies of the RH windshield were
damaged, due to a continuous arcing in the windshield heating system (at the level
of the power supply wires). Such electrical arcing requires a combination of at least
the following contributing factors: mechanical damage to the insulation sleeve of
the power supply wires and water ingress resulting in the wires corrosion. Several
tens of seconds after the failure of the 2 structural plies, the last ply failed (outer ply,
nonstructural) and the windshield was ejected due to the pressurization loads.
Due to the similarity of design between A320, A330, A300-600 and A300 windshields,
an Inspection Service Bulletin (ISB) is required for the A300 family aircraft.
In addition, the Modification (MOD) No. 13907S22976 (WINDOWS - COCKPIT -
INTRODUCE IMPROVED SGS FRONT WINDSHIELD) will introduce the new Part Numbers
(PNs) SPSA340-2-6-3 (LH) and SPSA340-1-6-3 (RH) which are not affected by this ISB.
(2) Objective/Action
This Inspection Service Bulletin is published to advise all operators of the A300
family aircraft of the issue of Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001, which
provides instructions to inspect the front windshields potentially affected by water
ingress and corrosion within the windshield heating system. The SGS PNs (all serial
numbers) impacted have been defined in 3 groups:
Group 1:
- SPSA340-2-4-1 / SPSA340-1-4-1
Group 2:
- SPSA340-2-5-2 / SPSA340-1-5-2
Group 3:
- TGA300-2-2-1 / TGA300-1-2-1

### Page 3

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 3
- TGA300-2-2-2 / TGA300-1-2-2
- TGA300-2-3-3 / TGA300-1-3-3
- TGA300-2-3-4 / TGA300-1-3-4
- TGA300-2-4-5 / TGA300-1-4-5
- TGA300-2-4-6 / TGA300-1-4-6
- EWA300-2-4-5 / EWA300-1-4-5
- SPSA340-2-1-1 / SPSA340-1-1-1
- SPSA340-2-2-1 / SPSA340-1-2-1
- SPSA340-2-3-1 / SPSA340-1-3-1
NOTE: This Service Bulletin is applicable to all above base PNs, regardless of the
amendment letter.
(3) Advantages
Accomplishment of this Inspection Service Bulletin will enable an early detection of
potential water ingress and corrosion damage in the windshield electrical heating
system.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING NO
A/C OPERATION
AFFECTED
NO VENDOR SB YES
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
No material
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)

### Page 4

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 4
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Aircraft standard tools See SB See Note Windshield inspection tool
NOTE: Price information to be obtained from the given supplier.
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Aircraft standard tools See SB See Note Windshield inspection tool
NOTE: Price information to be obtained from the given supplier.
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
No material
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
No material
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
34O 50W A2S AFG AMA BCS F2I GLY IAW IRA IRM KGS KYE LOL MIX MNB MSR RUN STR TIW
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
AIRCRAFT NO
EQUIPMENT YES
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)

### Page 5

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 5
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
AIRCRAFT NO
EQUIPMENT YES
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
AIRCRAFT NO
EQUIPMENT YES
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
AIRCRAFT NO
EQUIPMENT YES
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
AIRCRAFT NO
EQUIPMENT YES
I. MANPOWER
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
MANPOWER
TOTAL MAN-HOURS 0.20 h
ELAPSED TIME (HOURS) 0.15 h
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
MANPOWER
TOTAL MAN-HOURS 3.00 h
ELAPSED TIME (HOURS) 1.70 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001

### Page 6

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 6
MANPOWER
Prepare the Weather Seal before
Electrical T ests in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Repair the Weather Seal in accordance
with VSB (Depending on the Inspection
Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
MANPOWER
TOTAL MAN-HOURS 3.00 h
ELAPSED TIME (HOURS) 1.70 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Prepare the Weather Seal before
Electrical T ests in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Repair the Weather Seal in accordance
with VSB (Depending on the Inspection
Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
MANPOWER
TOTAL MAN-HOURS 1.20 h
ELAPSED TIME (HOURS) 1.00 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)

### Page 7

A300
SERVICE BULLETIN
SUMMARY
REV 00 Nov 19/21 A300-56-0014
Page 7
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 10.00 h

### Page 8

A300
SERVICE BULLETIN
SUMMARY
Figure ICN-A300-A-56XX0014-A-FAPE3-007J1-A-001-01 Fig.SA Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014General overview
Page 8
J. GENERAL OVERVIEW
CONF ALL
A
INSPECTION OF THE FRONT WINDSHIELDS
FR1
FR11
A
Z211
Z212
LH
RH
ICN-A300-A-56XX0014-A-FAPE3-007J1-A-001-01

### Page 9

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 9
ATA SYSTEM: 56
TITLE: WINDOWS - FIXED WINDOWS - INSPECTION OF SAINT-GOBAIN SULLY
FRONT WINDSHIELD
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This Service Bulletin is only applicable to aircraft fitted with SAINT-GOBAIN SULLY
windshield and with these PNs, regardless the amendment letters:
- EWA300-1-4-5
- EWA300-2-4-5
- SPSA340-1-1-1
- SPSA340-2-1-1
- SPSA340-1-2-1
- SPSA340-2-2-1
- SPSA340-1-3-1
- SPSA340-2-3-1
- SPSA340-1-4-1
- SPSA340-2-4-1
- SPSA340-1-5-2
- SPSA340-2-5-2
- TGA300-1-2-1
- TGA300-2-2-1
- TGA300-1-2-2
- TGA300-2-2-2
- TGA300-1-3-3
- TGA300-2-3-3
- TGA300-1-3-4
- TGA300-2-3-4
- TGA300-1-4-5
- TGA300-2-4-5
- TGA300-1-4-6
- TGA300-2-4-6
NOTE: This Service Bulletin is not applicable to aircraft on which both PNs SPSA340-2-
6-3 and SPSA340-1-6-3 are installed (MOD No. 13907S22976 (WINDOWS - FIXED
WINDOWS - INTRODUCE IMPROVED SAINT-GOBAIN SULLY FRONT WINDSHIELD) is
embodied).
(1) Models
ON A/C 0003
B2-1C
ON A/C 0080, 0185, 0187, 0226
B2-203
ON A/C 0090, 0160, 0244
B2K-3C
ON A/C 0075, 0085, 0107, 0123, 0126, 0139, 0141, 0151, 0154, 0157, 0173, 0175, 0180,
0183, 0203, 0210, 0211, 0218, 0227, 0235, 0236, 0255, 0259, 0261, 0274, 0299, 0302, 0304
B4-203
ON A/C 0239, 0256
B4-2C
ON A/C 0212
C4-203

### Page 10

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 10
ON A/C 0277, 0292
F4-203
CONF ALL
(2) Applicability by MSN
0003 0075 0080 0085 0090 0107 0123 0126 0139 0141 0151 0154 0157 0160 0173
0175 0180 0183 0185 0187 0203 0210-0212 0218 0226 0227 0235 0236 0239 0244
0255 0256 0259 0261 0274 0277 0292 0299 0302 0304
(3) MSN by configuration
MSN CONFIGURATION
0003 0075 0080 0085 0090 0107 0123 0126 0139 0141 0151
0154 0157 0160 0173 0175 0180 0183 0185 0187 0203 0210
0211 0212 0218 0226 0227 0235 0236 0239 0244 0255 0256
0259 0261 0274 0277 0292 0299 0302 0304
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
AIRBUS received a report on an in-service event on A319 aircraft about the loss of the
RH side windshield in flight, during the cruise phase. The windshield was the original
from delivery, manufactured by SAINT-GOBAIN SULLY SAS (SGS). The investigation
of the A319 event determined that both structural plies of the RH windshield were
damaged, due to a continuous arcing in the windshield heating system (at the level
of the power supply wires). Such electrical arcing requires a combination of at least
the following contributing factors: mechanical damage to the insulation sleeve of
the power supply wires and water ingress resulting in the wires corrosion. Several
tens of seconds after the failure of the 2 structural plies, the last ply failed (outer ply,
nonstructural) and the windshield was ejected due to the pressurization loads.
Due to the similarity of design between A320, A330, A300-600 and A300 windshields,
an Inspection Service Bulletin (ISB) is required for the A300 family aircraft.
In addition, the Modification (MOD) No. 13907S22976 (WINDOWS - COCKPIT -
INTRODUCE IMPROVED SGS FRONT WINDSHIELD) will introduce the new Part Numbers
(PNs) SPSA340-2-6-3 (LH) and SPSA340-1-6-3 (RH) which are not affected by this ISB.
(2) Objective/Action
This Inspection Service Bulletin is published to advise all operators of the A300
family aircraft of the issue of Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001, which
provides instructions to inspect the front windshields potentially affected by water
ingress and corrosion within the windshield heating system. The SGS PNs (all serial
numbers) impacted have been defined in 3 groups:
Group 1:
- SPSA340-2-4-1 / SPSA340-1-4-1

### Page 11

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 11
Group 2:
- SPSA340-2-5-2 / SPSA340-1-5-2
Group 3:
- TGA300-2-2-1 / TGA300-1-2-1
- TGA300-2-2-2 / TGA300-1-2-2
- TGA300-2-3-3 / TGA300-1-3-3
- TGA300-2-3-4 / TGA300-1-3-4
- TGA300-2-4-5 / TGA300-1-4-5
- TGA300-2-4-6 / TGA300-1-4-6
- EWA300-2-4-5 / EWA300-1-4-5
- SPSA340-2-1-1 / SPSA340-1-1-1
- SPSA340-2-2-1 / SPSA340-1-2-1
- SPSA340-2-3-1 / SPSA340-1-3-1
NOTE: This Service Bulletin is applicable to all above base PNs, regardless of the
amendment letter.
(3) Advantages
Accomplishment of this Inspection Service Bulletin will enable an early detection of
potential water ingress and corrosion damage in the windshield electrical heating
system.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
1 Inspect the PN of the LH side Front Windshield on the Aircraft
2 Inspect the PN of the RH side Front Windshield on the Aircraft
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
1 Do the Inspection of the LH side Front Windshield
2 Do the Inspection of the RH side Front Windshield
3 Do a Detailed Inspection of the Connector in accordance with VSB
(Depending on the Inspection Result)
4 Prepare the Weather Seal before Electrical T ests in accordance with VSB
(Depending on the Inspection Result)

### Page 12

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 12
5 Repair the Weather Seal in accordance with VSB (Depending on the
Inspection Result)
6 Do a Shop Inspection of the Spare Windshield in accordance with VSB
(Depending on the Inspection Result)
7 Complete and Send the Inspection Report Sheet, LH side
8 Complete and Send the Inspection Report Sheet, RH side
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
1 Do the Inspection of the LH side Front Windshield
2 Do the Inspection of the RH side Front Windshield
3 Do a Detailed Inspection of the Connector in accordance with VSB
(Depending on the Inspection Result)
4 Prepare the Weather Seal before Electrical T ests in accordance with VSB
(Depending on the Inspection Result)
5 Repair the Weather Seal in accordance with VSB (Depending on the
Inspection Result)
6 Do a Shop Inspection of the Spare Windshield in accordance with VSB
(Depending on the Inspection Result)
7 Complete and Send the Inspection Report Sheet, LH side
8 Complete and Send the Inspection Report Sheet, RH side
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
1 Do the Inspection of the LH side Front Windshield
2 Do the Inspection of the RH side Front Windshield
3 Do a Detailed Inspection of the Connector in accordance with VSB
(Depending on the Inspection Result)
4 Do a Shop Inspection of the Spare Windshield in accordance with VSB
(Depending on the Inspection Result)
5 Complete and Send the Inspection Report Sheet, LH side
6 Complete and Send the Inspection Report Sheet, RH side
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
1 Remove the Damaged Front Windshield from the Aircraft, LH side
2 Remove the Damaged Front Windshield from the Aircraft, RH side
3 Install the Front Windshield on the Aircraft, LH side

### Page 13

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 13
4 Install the Front Windshield on the Aircraft, RH side
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done in accordance with the
accomplishment timescale given in the Appendix COMPLIANCE TIMES.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Union Aviation Safety Agency
(EASA) will be issued to confirm this classification. It is anticipated that the AD will
confirm the thresholds given but reference should be made to the AD for confirmation
of the mandated accomplishment timescale.
NOTE: For the presentation of the compliance times, refer to Appendix COMPLIANCE
TIMES.
NOTE: This Service Bulletin considers the possibility of a configuration with PNs from
different Groups on the LH and RH sides of the same aircraft.
NOTE: A review of aircraft delivery and/or maintenance records is acceptable to make
the determination of the part installed, provided those records can be relied upon
for that purpose and the PN and SN of the part can be positively identified from that
review.
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
PREPARATION
Job Set-up 0.05 h
PROCEDURE
Inspect the PN of the LH side Front Windshield on the
Aircraft
0.05 h
Inspect the PN of the RH side Front Windshield on the
Aircraft
0.05 h
PREPARATION FOR TEST

### Page 14

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 14
None
TEST
None
CLOSE-UP
Close-up 0.05 h
TOTAL MAN-HOURS 0.20 h
ELAPSED TIME (HOURS) 0.15 h
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
PREPARATION
Job Set-up 0.10 h
Remove for Access the Lining Panel from the Aircraft, LH
side
0.10 h
Remove for Access the Lining Panel from the Aircraft, RH
side
0.10 h
PROCEDURE
Do the Inspection of the LH side Front Windshield 1.10 h
Do the Inspection of the RH side Front Windshield 1.10 h
Complete and Send the Inspection Report Sheet, LH side 0.10 h
Complete and Send the Inspection Report Sheet, RH side 0.10 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Install the Lining Panel Removed for Access on the Aircraft,
LH side
0.10 h
Install the Lining Panel Removed for Access on the Aircraft,
RH side
0.10 h
Close-up 0.10 h
TOTAL MAN-HOURS 3.00 h
ELAPSED TIME (HOURS) 1.70 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Prepare the Weather Seal before
Electrical T ests in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Repair the Weather Seal in accordance
with VSB (Depending on the Inspection
Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001

### Page 15

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 15
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
PREPARATION
Job Set-up 0.10 h
Remove for Access the Lining Panel from the Aircraft, LH
side
0.10 h
Remove for Access the Lining Panel from the Aircraft, RH
side
0.10 h
PROCEDURE
Do the Inspection of the LH side Front Windshield 1.10 h
Do the Inspection of the RH side Front Windshield 1.10 h
Complete and Send the Inspection Report Sheet, LH side 0.10 h
Complete and Send the Inspection Report Sheet, RH side 0.10 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Install the Lining panel Removed for Access on the Aircraft,
LH side
0.10 h
Install the Lining panel Removed for Access on the Aircraft,
RH side
0.10 h
Close-up 0.10 h
TOTAL MAN-HOURS 3.00 h
ELAPSED TIME (HOURS) 1.70 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Prepare the Weather Seal before
Electrical T ests in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Repair the Weather Seal in accordance
with VSB (Depending on the Inspection
Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)

### Page 16

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 16
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
PREPARATION
Job Set-up 0.10 h
Remove for Access the Lining Panel from the Aircraft, LH
side
0.10 h
Remove for Access the Lining Panel from the Aircraft, RH
side
0.10 h
PROCEDURE
Do the Inspection of the LH side Front Windshield 0.25 h
Do the Inspection of the RH side Front Windshield 0.25 h
Complete and Send the Inspection Report Sheet, LH side 0.05 h
Complete and Send the Inspection Report Sheet, RH side 0.05 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Install the Lining panel Removed for Access on the Aircraft,
LH side
0.10 h
Install the Lining panel Removed for Access on the Aircraft,
RH side
0.10 h
Close-up 0.10 h
TOTAL MAN-HOURS 1.20 h
ELAPSED TIME (HOURS) 1.00 h
Additional man-hours related to Vendor SB; refer to:
Do a Detailed Inspection of the
Connector in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
Do a Shop Inspection of the Spare
Windshield in accordance with VSB
(Depending on the Inspection Result)
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-
001
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
PREPARATION
Job Set-up 4.50 h
PROCEDURE
Remove the Damaged Front Windshield from the Aircraft,
LH side
2.50 h
Remove the Damaged Front Windshield from the Aircraft,
RH side
2.50 h
Install the Front Windshield on the Aircraft, LH side 2.50 h
Install the Front Windshield on the Aircraft, RH side 2.50 h

### Page 17

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 17
PREPARATION FOR TEST
Job set-up 0.50 h
TEST
T est 0.50 h
CLOSE-UP
Close-up 4.50 h
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 10.00 h
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
(a) T ask set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of the PN of the
Front Windshields Installed on the Aircraft
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-21-00, Page Block 001 24-00-00, Page Block 301
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-55-00
TECHNICAL FOLLOW UP (TFU)
56.11.00014
(2) Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 1 (Depending on the PN of the Windshields)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-21-00, Page Block 001 20-16-00, Page Block 201
20-21-12, Page Block 001 24-00-00, Page Block 301
24-50-00, Page Block 001 25-13-00, Page Block 001
30-42-00, Page Block 501 56-10-00, Page Block 901
56-11-11, Page Block 401
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-54-50 20-55-00
IN SERVICE INFORMATION (ISI)
00.00.00179
MASTER MINIMUM EQUIPMENT LIST (MMEL)
1-30-9

### Page 18

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 18
NON DESTRUCTIVE TEST MANUAL (NTM)
51-40-00
STRUCTURAL REPAIR MANUAL (SRM)
51-30-29 51-40-20
TECHNICAL FOLLOW UP (TFU)
56.11.00014
VENDOR SERVICE BULLETIN (VSB)
SAINT-GOBAIN (F0360) VSB SPSA340-56-001
CONSUMABLE MATERIAL LIST (CML)
(3) Do a Detailed Inspection of the Front Windshields for Group 2 (Depending on
the PN of the Windshields)
(a) T ask set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 2 (Depending on the PN of the Windshields)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-21-00, Page Block 001 20-16-00, Page Block 201
20-21-12, Page Block 001 24-00-00, Page Block 301
24-50-00, Page Block 001 25-13-00, Page Block 001
30-42-00, Page Block 501 56-10-00, Page Block 901
56-11-11, Page Block 401
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-54-50 20-55-00
IN SERVICE INFORMATION (ISI)
00.00.00179
MASTER MINIMUM EQUIPMENT LIST (MMEL)
1-30-9
NON DESTRUCTIVE TEST MANUAL (NTM)
51-40-00
STRUCTURAL REPAIR MANUAL (SRM)
51-30-29 51-40-20
TECHNICAL FOLLOW UP (TFU)
56.11.00014
VENDOR SERVICE BULLETIN (VSB)
SAINT-GOBAIN (F0360) VSB SPSA340-56-001
CONSUMABLE MATERIAL LIST (CML)
(4) Do a Detailed Inspection of the Front Windshields for Group 3 (Depending on
the PN of the Windshields)

### Page 19

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 19
(a) T ask set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection of the Front
Windshields for Group 3 (Depending on the PN of the Windshields)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-21-00, Page Block 001 20-16-00, Page Block 201
20-21-12, Page Block 001 24-00-00, Page Block 301
24-50-00, Page Block 001 25-13-00, Page Block 001
30-42-00, Page Block 501 56-10-00, Page Block 901
56-11-11, Page Block 401
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-54-50 20-55-00
IN SERVICE INFORMATION (ISI)
00.00.00179
MASTER MINIMUM EQUIPMENT LIST (MMEL)
1-30-9
NON DESTRUCTIVE TEST MANUAL (NTM)
51-40-00
STRUCTURAL REPAIR MANUAL (SRM)
51-30-29
TECHNICAL FOLLOW UP (TFU)
56.11.00014
VENDOR SERVICE BULLETIN (VSB)
SAINT-GOBAIN (F0360) VSB SPSA340-56-001
(5) Do the Replacement of the Front Windshields on the Aircraft (Depending on
the Inspection Result)
(a) T ask set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of the Front
Windshields on the Aircraft (Depending on the Inspection Result)
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-21-00, Page Block 001 24-00-00, Page Block 301
56-11-11, Page Block 401
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-55-00
TECHNICAL FOLLOW UP (TFU)
56.11.00014
K. PUBLICATION AFFECTED
AIRCRAFT MAINTENANCE MANUAL (AMM)
L. INDUSTRY SUPPORT INFORMATION

### Page 20

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 20
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 21

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 21
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
No material for task set A300-A-56-XX-0014-01000-93BA-A Do an Inspection of
the PN of the Front Windshields Installed on the Aircraft
Material for task set A300-A-56-XX-0014-02000-93BA-A Do a Detailed Inspection
of the Front Windshields for Group 1 (Depending on the PN of the Windshields)
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Material for task set A300-A-56-XX-0014-03000-93BA-A Do a Detailed Inspection
of the Front Windshields for Group 2 (Depending on the PN of the Windshields)
MATERIAL QTY SEE NOTES
Aircraft standard tools See SB
Referenced tools See SB
Consumables See SB
Referenced consumables See SB
Material for task set A300-A-56-XX-0014-04000-93BA-A Do a Detailed Inspection
of the Front Windshields for Group 3 (Depending on the PN of the Windshields)
MATERIAL QTY SEE NOTES
Referenced tools See SB
Referenced consumables See SB
Material for task set A300-A-56-XX-0014-01000-93CA-A Do the Replacement of
the Front Windshields on the Aircraft (Depending on the Inspection Result)
MATERIAL QTY SEE NOTES
Referenced tools See SB
Referenced consumables See SB
B. TOOLING
Aircraft standard tools for task set A300-A-56-XX-0014-02000-93BA-A Do a
Detailed Inspection of the Front Windshields for Group 1 (Depending on the PN of
the Windshields)
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)

### Page 22

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 22
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98D56003001000
(D4296) 1 WINDSHIE (1)
98D56003001001
(D4296) 1 HARNESS
98D56003001002
(D4296) 1 WINDSHIE (1)
NOTE(S)
(1): PN 98D56003001002 is alternative of the existing PN 98D56003001000.
Aircraft standard tools for task set A300-A-56-XX-0014-03000-93BA-A Do a
Detailed Inspection of the Front Windshields for Group 2 (Depending on the PN of
the Windshields)
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
Customer Order Fulfilment
Weg beim Jaeger 150
22335 HAMBURG
GERMANY
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact
(SPOC)
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98D56003001000
(D4296) 1 WINDSHIE (1)
98D56003001001
(D4296) 1 HARNESS
98D56003001002
(D4296) 1 WINDSHIE (1)
NOTE(S)
(1): PN 98D56003001002 is alternative of the existing PN 98D56003001000.
Referenced tools for task set A300-A-56-XX-0014-02000-93BA-A Do a Detailed
Inspection of the Front Windshields for Group 1 (Depending on the PN of the
Windshields)
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced tools for task set A300-A-56-XX-0014-03000-93BA-A Do a Detailed
Inspection of the Front Windshields for Group 2 (Depending on the PN of the
Windshields)

### Page 23

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 23
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced tools for task set A300-A-56-XX-0014-04000-93BA-A Do a Detailed
Inspection of the Front Windshields for Group 3 (Depending on the PN of the
Windshields)
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced tools for task set A300-A-56-XX-0014-01000-93CA-A Do the
Replacement of the Front Windshields on the Aircraft (Depending on the
Inspection Result)
T o accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM 56-11-11, Page Block 401
C. CONSUMABLES
Consumables for task set A300-A-56-XX-0014-02000-93BA-A Do a Detailed
Inspection of the Front Windshields for Group 1 (Depending on the PN of the
Windshields)
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06AFB1 Polysulfide Sealant -Windshield Fillet
Consumables for task set A300-A-56-XX-0014-03000-93BA-A Do a Detailed
Inspection of the Front Windshields for Group 2 (Depending on the PN of the
Windshields)
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
06AFB1 Polysulfide Sealant -Windshield Fillet
Referenced consumables for task set A300-A-56-XX-0014-02000-93BA-A Do a
Detailed Inspection of the Front Windshields for Group 1 (Depending on the PN of
the Windshields)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced consumables for task set A300-A-56-XX-0014-03000-93BA-A Do a
Detailed Inspection of the Front Windshields for Group 2 (Depending on the PN of
the Windshields)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced consumables for task set A300-A-56-XX-0014-04000-93BA-A Do a
Detailed Inspection of the Front Windshields for Group 3 (Depending on the PN of
the Windshields)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:

### Page 24

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 24
Ref. AMM 56-11-11, Page Block 401
Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Referenced consumables for task set A300-A-56-XX-0014-01000-93CA-A Do
the Replacement of the Front Windshields on the Aircraft (Depending on the
Inspection Result)
T o accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM 56-11-11, Page Block 401
D. LIST OF NEW PARTS
No parts
E. LIST OF EXISTING PARTS
No parts

### Page 25

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 25
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A300-A-56-XX-0014-01000-93BA-A (A300-A-56-XX-0014-01ZZZ-93BZ-A)
Do an Inspection of the PN of the Front Windshields Installed on the Aircraft
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 0.20 h
ELAPSED TIME (HOURS) 0.15 h

### Page 26

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 26
B. PREPARATION
(1) Task A300-A-56-XX-0014-01001-540A-A (A300-A-56-XX-0014-01ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.05 h
Minimum Number of person 1
Elapsed Time 0.05 h
Referenced Information
Manuals/Drawings References/Sheets
AMM 24-00-00, Page Block 301
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM 24-00-00,
Page Block 301.
C. PROCEDURE
(1) Task A300-A-56-XX-0014-01001-900A-A (A300-A-56-XX-0014-01ZZZ-900Z-A)
Inspect the PN of the LH side Front Windshield on the Aircraft
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
211
Manpower/Resources/Skills
Man-hours 0.05 h
Minimum Number of person 1
Elapsed Time 0.05 h
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-21-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
(b) Inspect the PN of the LH side front windshield on the aircraft in accordance with
PLANNING INFORMATION paragraph 1.E.(2):
Refer to Ref. Fig.BC Inspection of the PN of the LH side Front Windshield on the
Aircraft and refer to Ref. Fig.FA Flow Chart.
NOTE: This Service Bulletin considers the possibility of a configuration with PNs
from different Groups on the LH and RH sides of the same aircraft.

### Page 27

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 27
NOTE: A review of aircraft delivery and/or maintenance records is acceptable
to make the determination of the part installed, provided those records
can be relied upon for that purpose and the PN and SN of the part can
be positively identified from that review.
NOTE: The paper ID plate bonded on the internal side of the windshield must
be used. If the paper ID plate is not available, the metallic ID plate on
the connector must be used (lining panel to be removed).
1 If the PN of the LH side front windshield is SPSA340-2-4-1:
a Do the inspection of the LH side front windshield for Group 1 in
accordance with Ref. T ask set A300-A-56-XX-0014-02ZZZ-93BZ-A.
2 If the PN of the LH side front windshield is SPSA340-2-5-2:
a Do a check of the sensor fault history from the date on which the
windshield has been first installed on any aircraft (current and
previous aircraft):
NOTE: T o ease the review of sensor fault history and records, do
a check if no warning light “WINDOW” on Master Warning
panel of 4VU. If this warning is not found in the aircraft
maintenance records, you can consider no sensor fault
occurred.
NOTE: For original windshield installed since the aircraft delivery:
- Do the check of the sensor fault history since aircraft
delivery date, refer to Ref. Appendix Presentation of the
Maintenance History.
<1> If sensor fault light on windows temperature controller (20DG)
has been recorded or if unknown maintenance history:
<a> Do the inspection of the LH side front windshield for Group
2, refer to Ref. T ask set A300-A-56-XX-0014-03ZZZ-93BZ-
A at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2).
<2> If sensor fault light on windows temperature controller (20DG)
has not been recorded:

### Page 28

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 28
<a> Do a check of the age of the windshield to know if it is
more or less than 4 years or 10000 FC or 15000 FH since
first installation on any aircraft.
NOTE: Regarding the definition of windshield age
utilization:
- For original windshield installed since the
aircraft delivery: take into account the age
of 4 years from aircraft delivery date.
- For windshield installed after the aircraft
delivery (installed in-service as a new
spare): take into account the age of 4 years
from windshield first installation date on any
aircraft (current and previous aircraft).
- If no data, or only partial data, is available,
refer to the guidance specified in
Airworthiness Limitations Section (ALS)
Part 1 Section 1 Chapter 5.2 (traceability)
to determine the age/utilization of the
windshield.
- For repaired windshields provided with an
Authorized Release Certificate (ARC) (Form
One) granted by SAINT-GOBAIN SULLY with
the mention "Outer ply replacement": take
into account the first installation date with
0FH/0FC accumulated and no age at this
date (considered as new).
- For spare windshield repaired with ARC
form one without "Outer ply replacement":
previous utilization to be taken into account
from windshield first installation date on any
aircraft (current and previous aircraft).
<b> Record the test result on the Inspection Report sheet.
<c> Do the inspection of the LH side front windshield for Group
2, refer to Ref. T ask set A300-A-56-XX-0014-03ZZZ-93BZ-
A at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2).
3 If the PN of the LH side front windshield is SPSA340-2-1-1 or SPSA340-2-2-
1 or SPSA340-2-3-1 or TGA300-2-2-1 or TGA300-2-2-2 or TGA300-2-3-3 or
TGA300-2-3-4 or TGA300-2-4-5 or TGA300-2-4-6 or EWA300-2-4-5:
a Do the inspection of the LH side front windshield for Group 3 in
accordance with Ref. T ask set A300-A-56-XX-0014-04ZZZ-93BZ-A.
4 If the PN of the LH side front windshield is different than SPSA340-2-1-
1 or SPSA340-2-2-1 or SPSA340-2-3-1 or SPS340-2-4-1 or SPSA340-2-5-
2 or TGA300-2-2-1 or TGA300-2-2-2 or TGA300-2-3-3 or TGA300-2-3-4 or
TGA300-2-4-5 or TGA300-2-4-6 or EWA300-2-4-5:
a No further action is necessary with this Service Bulletin.

### Page 29

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IQ-A-001-01 Fig.BC Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Inspection of the PN of the LH side
Front Windshield on the Aircraft Page 29
CONF ALL
A
B
NOTE:
USE THE PAPER ID PLATE TO IDENTIFY THE PIN OF THE FRONT WINDSHIELD, ON01
THE AIRCRAFT, LH SIDE.
FIRST CHECK PAPER ID PLATE (AS SHOWN ON VIEW A). IF NOT FOUND CHECK THE02
CONNECTOR ON ALL 4 SIDES FOR THE IDENTIFICATION OF THE FRONT WINDSHIELD
ON THE AIRCRAFT, LH SIDE.
VIEW LOOKING FWD
VIEW LOOKING FWD
01
02
A
B
ICN-A300-A-56XX0014-A-FAPE3-007IQ-A-001-01

### Page 30

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007GN-A-001-01 Fig.FA Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Flow Chart
Page 30
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE
TIMES GIVEN IN THIS SERVICE BULLETIN.
01
IF A FAULT MESSAGE IS RECORDED OR IF THE MAINTENANCE HISTORY IS UNKNOWN, DO THE INSPECTION.02
NOTE:
IN ACCORDANCE WITH PLANNING INFORMATION PARAGRAPH 1.E.(2).
NO
INSTALLED?
IS
YES
01
DO THE INSPECTION OF THE
LH SIDE FRONT WINDSHIELD
FOR GROUP 1
01
LH SIDE FRONT WINDSHIELD
ON THE AIRCRAFT
INSTALLED?
PN SPSA340-2-4-1
IS
YES
YES
01
DO THE INSPECTION OF THE
LH SIDE FRONT WINDSHIELD
FOR GROUP 3
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
INSPECT THE PN OF THE
NO
YES
01 02
FRONT WINDSHIELD FOR GROUP 2
DO THE INSPECTION OF THE LH SIDE
01
IS FIRST INSTALLED ON ANY AIRCRAFT
FROM THE DATE ON WHICH THE WINDSHIELD
DO A CHECK OF THE SENSOR FAULT HISTORY
NOYES
PN SPSA340-2-5-2
NO
HAS SENSOR FAULT LIGHT
ON WINDOWS TEMPERATURE
CONTROLLER 20DG BEEN
RECORDED?
> 4 YEARS
OR > 10000 FC
OR > 15000 FH
SINCE FIRST
INSTALLATION ON
ANY AIRCRAFT?
WINDSHIELD AGE:
IS THE
IS PN TGA300-2-2-1
OR TGA300-2-3-4 OR TGA300-2-4-5
OR TGA300-2-4-6 OR EWA300-2-4-5 OR
OR TGA300-2-2-2 OR TGA300-2-3-3
SPSA340-2-1-1 OR SPSA340-2-2-1
OR SPSA340-2-3-1
INSTALLED?
ICN-A300-A-56XX0014-A-FAPE3-007GN-A-001-01

### Page 31

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 31
(2) Task A300-A-56-XX-0014-02001-900A-A (A300-A-56-XX-0014-02ZZZ-900Z-A)
Inspect the PN of the RH side Front Windshield on the Aircraft
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
212
Manpower/Resources/Skills
Man-hours 0.05 h
Minimum Number of person 1
Elapsed Time 0.05 h
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-21-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
(b) Inspect the PN of the RH side front windshield on the aircraft in accordance with
PLANNING INFORMATION paragraph 1.E.(2):
Refer to Ref. Fig.BD Inspection of the PN of the RH side Front Windshield on the
Aircraft and refer to Ref. Fig.FB Flow Chart.
NOTE: This Service Bulletin considers the possibility of a configuration with PNs
from different Groups on the LH and RH sides of the same aircraft.
NOTE: A review of aircraft delivery and/or maintenance records is acceptable
to make the determination of the part installed, provided those records
can be relied upon for that purpose and the PN and SN of the part can
be positively identified from that review.
NOTE: The paper ID plate bonded on the internal side of the windshield must
be used. If the paper ID plate is not available, the metallic ID plate on
the connector must be used (lining panel to be removed).
1 If the PN of the RH side front windshield is SPSA340-1-4-1:
a Do the inspection of the RH side front windshield for Group 1 in
accordance with Ref. T ask set A300-A-56-XX-0014-02ZZZ-93BZ-A.
2 If the PN of the RH side front windshield is SPSA340-1-5-2:
a Do a check of the sensor fault history from the date on which the
windshield has been first installed on any aircraft (current and
previous aircraft):
NOTE: T o ease the review of sensor fault history and records, do
a check if no warning light “WINDOW” on Master Warning
panel of 4VU. If this warning is not found in the aircraft
maintenance records, you can consider no sensor fault
occurred.

### Page 32

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 32
NOTE: For original windshield installed since the aircraft delivery:
- Do the check of the sensor fault history since aircraft
delivery date, refer to Ref. Appendix Presentation of the
Maintenance History.
<1> If sensor fault light on windows temperature controller (19DG)
has been recorded or if unknown maintenance history:
<a> Do the inspection of the RH side front windshield for
Group 2, refer to Ref. T ask set A300-A-56-XX-0014-03ZZZ-
93BZ-A at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2).
<2> If sensor fault light on windows temperature controller (19DG)
has not been recorded:
<a> Do a check of the age of the windshield to know if it is
more or less than 4 years or 10000 FC or 15000 FH since
first installation on any aircraft.
NOTE: Regarding the definition of windshield age
utilization:
- For original windshield installed since the
aircraft delivery: take into account the age
of 4 years from aircraft delivery date.
- For windshield installed after the aircraft
delivery (installed in-service as a new
spare): take into account the age of 4 years
from windshield first installation date on any
aircraft (current and previous aircraft).
- If no data, or only partial data, is available,
refer to the guidance specified in
Airworthiness Limitations Section (ALS)
Part 1 Section 1 Chapter 5.2 (traceability)
to determine the age/utilization of the
windshield.
- For repaired windshields provided with an
Authorized Release Certificate (ARC) (Form
One) granted by SAINT-GOBAIN SULLY with
the mention "Outer ply replacement": take
into account the first installation date with
0FH/0FC accumulated and no age at this
date (considered as new).
- For spare windshield repaired with ARC
form one without "Outer ply replacement":
previous utilization to be taken into account
from windshield first installation date on any
aircraft (current and previous aircraft).
<b> Record the test result on the Inspection Report sheet.
<c> Do the inspection of the RH side front windshield for
Group 2, refer to Ref. T ask set A300-A-56-XX-0014-03ZZZ-
93BZ-A at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2).
3 If the PN of the RH side front windshield is SPSA340-1-1-1 or SPSA340-1-2-
1 or SPSA340-1-3-1 or TGA300-1-2-1 or TGA300-1-2-2 or TGA300-1-3-3 or
TGA300-1-3-4 or TGA300-1-4-5 or TGA300-1-4-6 or EWA300-1-4-5:

### Page 33

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 33
a Do the inspection of the RH side front windshield for Group 3 in
accordance with Ref. T ask set A300-A-56-XX-0014-04ZZZ-93BZ-A.
4 If the PN of the RH side front windshield is different than SPSA340-1-1-1
or SPSA340-1-2-1 or SPSA340-1-3-1 or SPSA340-1-4-1 or SPSA340-1-5-
2 or TGA300-1-2-1 or TGA300-1-2-2 or TGA300-1-3-3 or TGA300-1-3-4 or
TGA300-1-4-5 or TGA300-1-4-6 or EWA300-1-4-5:
a No further action is necessary with this Service Bulletin.

### Page 34

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IR-A-001-01 Fig.BD Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Inspection of the PN of the RH side
Front Windshield on the Aircraft Page 34
CONF ALL
A
NOTE:
USE THE PAPER ID PLATE TO IDENTIFY THE PIN OF THE FRONT WINDSHIELD, ON01
THE AIRCRAFT, RH SIDE.
FIRST CHECK PAPER ID PLATE (AS SHOWN ON VIEW A). IF NOT FOUND CHECK THE02
CONNECTOR ON ALL 4 SIDES FOR THE IDENTIFICATION OF THE FRONT WINDSHIELD
ON THE AIRCRAFT, RH SIDE.
01
02
B
VIEW LOOKING FWD
B
A
ICN-A300-A-56XX0014-A-FAPE3-007IR-A-001-01

### Page 35

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007GO-A-001-01 Fig.FB Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Flow Chart
Page 35
CONF ALL
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE
TIMES GIVEN IN THIS SERVICE BULLETIN.
01
IF A FAULT MESSAGE IS RECORDED OR IF THE MAINTENANCE HISTORY IS UNKNOWN, DO THE INSPECTION.02
NOTE:
IN ACCORDANCE WITH PLANNING INFORMATION PARAGRAPH 1.E.(2).
NO
INSTALLED?
IS
YES
01
DO THE INSPECTION OF THE
RH SIDE FRONT WINDSHIELD
FOR GROUP 1
01
RH SIDE FRONT WINDSHIELD
ON THE AIRCRAFT
INSTALLED?
PN SPSA340-1-4-1
IS
YES
YES
01
DO THE INSPECTION OF THE
RH SIDE FRONT WINDSHIELD
FOR GROUP 3
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
NO
INSPECT THE PN OF THE
NO
YES
01 02
FRONT WINDSHIELD FOR GROUP 2
DO THE INSPECTION OF THE RH SIDE
01
IS FIRST INSTALLED ON ANY AIRCRAFT
FROM THE DATE ON WHICH THE WINDSHIELD
DO A CHECK OF THE SENSOR FAULT HISTORY
NOYES
PN SPSA340-1-5-2
NO
HAS SENSOR FAULT LIGHT
ON WINDOWS TEMPERATURE
CONTROLLER 19DG BEEN
RECORDED?
> 4 YEARS
OR > 10000 FC
OR > 15000 FH
SINCE FIRST
INSTALLATION ON
ANY AIRCRAFT?
WINDSHIELD AGE:
IS THE
IS PN TGA300-1-2-1
OR TGA300-1-3-4 OR TGA300-1-4-5
OR TGA300-1-4-6 OR EWA300-1-4-5 OR
OR TGA300-1-2-2 OR TGA300-1-3-3
SPSA340-1-1-1 OR SPSA340-1-2-1
OR SPSA340-1-3-1
INSTALLED?
ICN-A300-A-56XX0014-A-FAPE3-007GO-A-001-01

### Page 36

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 36
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A300-A-56-XX-0014-01001-740A-A (A300-A-56-XX-0014-01ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.05 h
Minimum Number of person 1
Elapsed Time 0.05 h
Procedure
NOTE: If you intend to accomplish an associated Inspection T ask during the same
layover period, the subsequent Close-up procedure is not necessary.
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Re-install the lining panel(s) if previously removed.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A300-A-56-XX-0014-01001-90AA-A (A300-A-56-XX-0014-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 37

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 37
Task set A300-A-56-XX-0014-02000-93BA-A (A300-A-56-XX-0014-02ZZZ-93BZ-A)
Do a Detailed Inspection of the Front Windshields for Group 1 (Depending on the PN of the
Windshields)
WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND
ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU
CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.
WARNING: BEFORE YOU DO THIS TASK:
- MAKE SURE THAT THE AREA BELOW THE WORK AREA IS CLEAR OF
PERSONS
- PUT PROTECTION ON THE PARTS BELOW THE WORK AREA IF
APPLICABLE.
IF OBJECTS FALL ACCIDENTALLY, THEY CAN CAUSE INJURY TO PERSONS AND/
OR DAMAGE TO THE AIRCRAFT.
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.

### Page 38

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 38
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including Required for Compliance paragraph
contained herein, contact AIRBUS for further instructions and approval.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure and
Compliance paragraphs and not to serve as the primary source for tasks or compliance
times given in this Service Bulletin.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 3.00 h
ELAPSED TIME (HOURS) 1.70 h
Additional man-hours related to Vendor SB; refer to:
SAINT-GOBAIN (F0360) VSB SPSA340-56-001
B. PREPARATION
(1) Task A300-A-56-XX-0014-02001-540A-A (A300-A-56-XX-0014-02ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 1
Elapsed Time 0.10 h
Referenced Information
Manuals/Drawings References/Sheets
AMM 24-00-00, Page Block 30156-11-11, Page Block 401
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM 24-00-00,
Page Block 301.
(b) Put an access platform 5M (16 FT) in position at Zone 210.
(c) Do the job set-up procedure as specified in the installation of the windshields,
refer to Ref. AMM 56-11-11, Page Block 401.
NOTE: It is not required to remove the windshield wiper arm.
(2) Task A300-A-56-XX-0014-03001-540A-A (A300-A-56-XX-0014-03ZZZ-540Z-A)
Remove for Access the Lining Panel from the Aircraft, LH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
211

### Page 39

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 39
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 1
Elapsed Time 0.10 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-21-00, Page Block 00125-13-00, Page Block 001
SRM 51-30-29
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
2 Remove and install fasteners in accordance with Ref. SRM 51-30-29.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) Remove the lining panel, for access, refer to Ref. AMM 25-13-00, Page Block 001
and refer to Ref. Fig.BE Removal of the Lining Panel for Access, LH side.
3 SCREW   Item (2) Retain
1 LINING PANEL   Item (1) Retain

### Page 40

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IV-A-001-01 Fig.BE Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Removal of the Lining Panel for Access, LH side
Page 40
CONF ALL
A
(2)
(1)
A
ICN-A300-A-56XX0014-A-FAPE3-007IV-A-001-01

### Page 41

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 41
(3) Task A300-A-56-XX-0014-04001-540A-A (A300-A-56-XX-0014-04ZZZ-540Z-A)
Remove for Access the Lining Panel from the Aircraft, RH side
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
212
Manpower/Resources/Skills
Man-hours 0.10 h
Minimum Number of person 1
Elapsed Time 0.10 h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-21-00, Page Block 00125-13-00, Page Block 001
SRM 51-30-29
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
2 Remove and install fasteners in accordance with Ref. SRM 51-30-29.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) Remove the lining panel, for access, refer to Ref. AMM 25-13-00, Page Block 001
and refer to Ref. Fig.BF Removal of the Lining Panel for Access, RH side.
3 SCREW   Item (2) Retain
1 LINING PANEL   Item (1) Retain

### Page 42

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IS-A-001-01 Fig.BF Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Removal of the Lining Panel for Access, RH side
Page 42
CONF ALL
A
(2)
A
(1)
ICN-A300-A-56XX0014-A-FAPE3-007IS-A-001-01

### Page 43

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 43
C. PROCEDURE
(1) Task A300-A-56-XX-0014-01001-311A-A (A300-A-56-XX-0014-01ZZZ-311Z-A)
Do the Inspection of the LH side Front Windshield
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
211
Manpower/Resources/Skills
Man-hours 1.10 h
Minimum Number of person 2
Elapsed Time 0.55 h
Skills Airframe
Material necessary to do the job
Aircraft standard tools
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98D56003001000 1 WINDSHIE (1)
98D56003001001 1 HARNESS
98D56003001002 1 WINDSHIE (1)
NOTE(S)
(1): PN 98D56003001002 is alternative of the existing PN 98D56003001000.
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-21-00, Page Block 001
20-16-00, Page Block 201
24-50-00, Page Block 001
30-42-00, Page Block 501
56-10-00, Page Block 901
ESPM 20-54-50
MMEL 1-30-9
NTM 51-40-00
VSB SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Procedure
NOTE: This procedure is to be done only if the LH side front windshield installed on
aircraft is in Group 1, refer to Ref. T ask set A300-A-56-XX-0014-01ZZZ-93BZ-A.
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
2 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
3 For the circuit breaker safety practices, refer to Ref. AMM 20-16-00, Page
Block 201.

### Page 44

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 44
(b) Do the inspection of the LH side front windshield for Group 1, refer to Ref.
Fig.FC Flow Chart at the compliance time defined in accordance with PLANNING
INFORMATION paragraph 1.E. (2):
1 Do a detailed visual inspection of the LH side front windshield from
outside to detect delamination or bubbles, refer to Ref. Fig.BA Criteria of
Delamination and Bubbles, LH side:
a If delamination and/or bubbles are visible:
<1> At outboard edge:
<a> Record the findings in the inspection report sheet, refer to
Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
<b> Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to Ref. AMM
56-10-00, Page Block 901, and then fly under Ref.
MMEL 1-30-9
Or
- Do step (d) before next flight.
<2> At upper, inboard and lower edges, do a check for the width of
the delamination and/or bubbles from the weather seal around
the front windshield:
<a> If delamination and/or bubbles are above the criteria
defined in Ref. Fig.BA Criteria of Delamination and
Bubbles, LH side:
[1] Record the findings in the inspection report sheet,
refer to Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
[2] Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to
Ref. AMM 56-10-00, Page Block 901, and then
fly under Ref. MMEL 1-30-9.
Or
- Do step (d) before next flight.
<b> If delamination and/or bubbles are not above the criteria
defined in Ref. Fig.BA Criteria of Delamination and
Bubbles, LH side:
[1] Record the findings in the inspection report sheet,
refer to Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
[2] Do step (b)2.
b If delamination and/or bubbles are not visible:
<1> Record the nil finding in the inspection report sheet, refer to Ref.
T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
<2> Do step (b)2.
2 Do the operational test of the windshield anti-icing and defogging, refer to
Ref. AMM 30-42-00, Page Block 501:
a If fault found, use dedicated TSM.
WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE
WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.

### Page 45

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 45
3 Open, safety/lock and tag this (these) circuit breaker(s):
PANEL DESIGNATION FIN LOCATION SEE NOTES
ALT1/WINDSHIELDS/HEATERS/
FRONT
1DG
ALT2/WINDSHIELDS/HEATERS/
FRONT
2DG
FRONT WINDOW/LH/WARN/LT 3DG
FRONT WINDOW/LH/TEMP/REGUL 5DG
FRONT WINDOW/LH/PWR/CONTRL 7DG
RADIO NAV & COM/RADAR TR1 7SQ1
If installed, open, safety/lock and tag this circuit breaker:
PANEL DESIGNATION FIN LOCATION SEE NOTES
RADIO NAV & COM/RADAR TR2 7SQ2
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00, Page
Block 001.
4 Disconnect the windshield connector from the aircraft wiring, refer to Ref.
Fig.BI Disconnection/Connection of the Front Windshield Connector from
the Aircraft Wiring, LH side.
5 Open the connector in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-311Z-A.
6 Do the detailed visual inspection of the connector in accordance with Ref.
SAINT-GOBAIN (F0360) VSB SPSA340-56-001 and refer to Ref. T ask A300-A-
56-XX-0014-03ZZZ-311Z-A:
NOTE: Record the result of inspection for all the connector visual
inspection steps in the Inspection Report sheet, refer to Ref. T ask
A300-A-56-XX-0014-02ZZZ-90AZ-A.
a If the connector cannot be opened for inspection:
<1> Close the connector in accordance with Ref. SAINT-GOBAIN
(F0360) VSB SPSA340-56-001 and refer to Ref. T ask A300-A-56-
XX-0014-03ZZZ-311Z-A.
<2> Connect the windshield connector to the aircraft wiring.
<3> Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to Ref. AMM 56-
10-00, Page Block 901, and then fly under Ref. MMEL 1-30-
9
Or
- Do step (d) before next flight.
b If the connector can be opened for inspection:
<1> Do a check for water ingress or corrosion in the windshield
connector:
NOTE: Refer to Ref. NTM 51-40-00 for using the recommended
endoscope or similar visual inspection aids.

### Page 46

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 46
<a> If water ingress or corrosion is found in the windshield
connector:
[1] Close the connector in accordance with Ref. SAINT-
GOBAIN (F0360) VSB SPSA340-56-001 and refer to
Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
[2] Connect the windshield connector to the aircraft
wiring.
[3] Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to
Ref. AMM 56-10-00, Page Block 901, and then
fly under Ref. MMEL 1-30-9.
Or
- Do step (d) before next flight.
<b> If water ingress or corrosion is not found in the windshield
connector:
[1] Do step (b)7.
7 Close the connector in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-311Z-A.
8 Connect the windshield connector to the aircraft wiring, refer to Ref. Fig.BI
Disconnection/Connection of the Front Windshield Connector from the
Aircraft Wiring, LH side.
9 Do the operational test of the windshield anti-icing and defogging, refer to
Ref. AMM 30-42-00, Page Block 501:
a If fault found, use dedicated TSM.
WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE
WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.
10 Open, safety/lock and tag this (these) circuit breaker(s):
PANEL DESIGNATION FIN LOCATION SEE NOTES
ALT1/WINDSHIELDS/HEATERS/
FRONT
1DG
ALT2/WINDSHIELDS/HEATERS/
FRONT
2DG
FRONT WINDOW/LH/WARN/LT 3DG
FRONT WINDOW/LH/TEMP/REGUL 5DG
FRONT WINDOW/LH/PWR/CONTRL 7DG
RADIO NAV & COM/RADAR TR1 7SQ1
If installed, open, safety/lock and tag this circuit breaker:
PANEL DESIGNATION FIN LOCATION SEE NOTES
RADIO NAV & COM/RADAR TR2 7SQ2
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00, Page
Block 001.

### Page 47

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 47
11 Disconnect the windshield connector from the aircraft wiring, refer to Ref.
Fig.BI Disconnection/Connection of the Front Windshield Connector from
the Aircraft Wiring, LH side.
12 Do the dielectric test and then the insulation test, refer to Ref. Appendix
ELECTRICAL TESTS RESULT CHART:
a Remove a part of the weather seal over the metallic Z bar in
accordance with Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-900Z-A.
WARNING: THE GSE TOOLS 98D56003001000, 98D56003001001
AND 98D56003001002 USE HIGH VOLTAGE DURING THE
TEST. BEFORE YOU START THE TEST, MAKE SURE THAT
ALL SAFETY PRECAUTIONS GIVEN IN THE TOOL USER
GUIDE ARE FOLLOWED. THE ELECTRICAL POWER IS
SUFFICIENTLY STRONG TO CAUSE AN INJURY OR KILL
YOU.
b Do the dielectric test (1500VAC during 1 minute) and insulation test
(500VDC during 1 minute), use tools:
1 WINDSHIELD
INSPECTION
98D56003001000  
or
1 WINDSHIELD
INSPECTION
98D56003001002  
and
1 HARNESS LR AND WB 98D56003001001  
NOTE: You must obey the instruction given in the GSE tool user
guide.
c Record the values in the inspection report sheet in accordance
with Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A and refer to Ref.
Appendix ELECTRICAL TESTS RESULT CHART.
d Connect the windshield connector to the aircraft wiring.
e Examine the color classification of the results of the dielectric and
insulation tests, refer to Ref. Appendix ELECTRICAL TESTS RESULT
CHART:
<1> If the electrical tests result is in red area:
<a> Do step (c) or (d) before next flight.
<2> If the electrical tests result is in green or amber area:
<a> Do step (d) or do the steps that follow:
[1] Do the operational test of the windshield anti-icing
and defogging, refer to Ref. AMM 30-42-00, Page
Block 501:
[a] If fault found, use dedicated TSM.
[2] Repair the weather seal in accordance with Ref.
SAINT-GOBAIN (F0360) VSB SPSA340-56-001 and
refer to Ref. T ask A300-A-56-XX-0014-01ZZZ-690Z-A.

### Page 48

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 48
[3] Send the result to AIRBUS in accordance with Ref.
T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
[4] Do again the inspection of the LH side front
windshield for Group 1 at the compliance time
defined in accordance with PLANNING INFORMATION
paragraph 1.E.(2), refer to Ref. T ask A300-A-56-XX-
0014-01ZZZ-311Z-A.
(c) Do the operational test of the windshield anti-icing and defogging, refer to Ref.
AMM 30-42-00, Page Block 501 and Ref. Fig.FC Flow Chart at the compliance time
defined in accordance with PLANNING INFORMATION paragraph 1.E.(2).
1 If fault found, use dedicated TSM.
2 Repair the weather seal in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-01ZZZ-690Z-A.
3 Fly under MMEL:
- Deactivate the windshield de-icing, refer to Ref. AMM 56-10-00, Page
Block 901, and then fly under Ref. MMEL 1-30-9
(d) Replace the damaged windshield with a spare windshield, refer to Ref. Fig.FC
Flow Chart at the compliance time defined in accordance with PLANNING
INFORMATION paragraph 1.E.(2):
1 If this Service Bulletin is not applicable for the PN of the spare windshield:
a Replace the damaged windshield with a spare windshield in
accordance with Ref. T ask set A300-A-56-XX-0014-01ZZZ-93CZ-A.
b Send the windshield inspection report to AIRBUS (Monitored retrofit)
in accordance with Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
c No further action is necessary with this Service Bulletin.
2 If this Service Bulletin is applicable for the PN of the spare windshield:
a Do a check if the spare windshield was installed before on a different
aircraft:
<1> If the spare windshield was not installed before on a different
aircraft:
<a> Replace the damaged windshield with a spare windshield
in accordance with Ref. T ask set A300-A-56-XX-0014-
01ZZZ-93CZ-A and refer to Ref. Fig.FC Flow Chart.
<b> Send the windshield inspection report to AIRBUS
(Monitored retrofit) in accordance with Ref. T ask A300-A-
56-XX-0014-02ZZZ-90AZ-A.
<c> Do again the inspection of the LH side front windshield
at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2), refer to Ref.
T ask A300-A-56-XX-0014-01ZZZ-311Z-A.
<2> If the spare windshield was installed before on a different
aircraft:
NOTE: The shop inspection is not applicable to windshields in
shop and in stock, which have an Authorized Release
Certificate (ARC) (Form One) from SAINT-GOBAIN SULLY
with the indication “Outer ply replacement” with a total
of 0FH/0FC since new or repair.

### Page 49

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 49
<a> Do the shop inspection of the spare windshield in
accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-
0014-04ZZZ-311Z-A:
[1] If there is finding during the shop inspection:
[a] Select another spare windshield and do step
(d) again.
[2] If there is no finding during the shop inspection:
[a] Replace the damaged windshield with a spare
windshield in accordance with Ref. T ask set
A300-A-56-XX-0014-01ZZZ-93CZ-A and refer to
Ref. Fig.FC Flow Chart.
[b] Send the windshield inspection report to
AIRBUS (Monitored retrofit) in accordance with
Ref. T ask A300-A-56-XX-0014-02ZZZ-90AZ-A.
[c] Do again the inspection of the LH side front
windshield at the compliance time defined
in accordance with PLANNING INFORMATION
paragraph 1.E.(2), refer to Ref. T ask A300-A-56-
XX-0014-01ZZZ-311Z-A.

### Page 50

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007GJ-A-001-01 Fig.FC Sol.AA SHEET 1/2
REV 00 Nov 19/21 A300-56-0014Flow Chart
Page 50
CONF ALL
01
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND
COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE
TIMES GIVEN IN THIS SERVICE BULLETIN.
IN ACCORDANCE WITH PLANNING INFORMATION PARAGRAPH 1.E.(2)
A
DO A DETAILED VISUAL INSPECTION OF THE
LH SIDE FRONT WINDSHIELD FROM OUTSIDE
TO DETECT DELAMINATION AND/OR BUBBLES
01
01
FRONT WINDSHIELD FOR GROUP 1
DO THE INSPECTION OF THE LH SIDE
ARE DELAMINATION AND/OR
BUBBLES VISIBLE AT OUTBOARD,
INBOARD, UPPER AND LOWER EDGES
OR ABOVE THE CRITERIA
DEFINED?
01
IN ACCORDANCE WITH VSB
DO THE DETAILED VISUAL INSPECTION OF THE CONNECTOR
CAN
CONNECTOR BE
OPENED FOR
INSPECTION?
YES
NO
IS WATER INGRESS
OR CORROSION FOUND
IN THE WINDSHIELD
CONNECTOR?
OR
B NO
NO
DE-ICING AND FLY UNDER
MMEL 1-30-9
01
DEACTIVATE THE WINDSHIELD
YES
C
01
IN THE INSPECTION REPORT SHEET
INSULATION TEST AND RECORD THE VALUES
DO THE DIELECTRIC TEST AND THEN THE
YES
ICN-A300-A-56XX0014-A-FAPE3-007GJ-A-001-01

### Page 51

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007GK-A-001-01 Fig.FC Sol.AA SHEET 2/2
REV 00 Nov 19/21 A300-56-0014Flow Chart
Page 51
CONF ALL
01
NOTE:
THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND
COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE
TIMES GIVEN IN THIS SERVICE BULLETIN.
IN ACCORDANCE WITH PLANNING INFORMATION PARAGRAPH 1.E.(2)
A
OR
REPAIR THE WEATHER SEAL
IN ACCORDANCE WITH VSB
01
DE-ICING AND FLY UNDER
MMEL 1-30-9
01
DEACTIVATE THE WINDSHIELD
ARE THE
DIELECTRIC AND INSULATION
VALUES RECORDED IN
THE GREEN OR AMBER
AREA?
NO
YESOR
IS
THIS SERVICE BULLETIN
APPLICABLE FOR THE PN OF
THE SPARE WINDSHIELD?
01
REPORT TO AIRBUS (MONITORED RETROFIT)
SEND THE WINDSHIELD INSPECTION
NO FURTHER ACTION WITH
THIS SERVICE BULLETIN
SHOP
INSPECTION?
FINDING DURING
IS THERE ANY
YES
OF THE SPARE WINDSHIELD
DO THE SHOP INSPECTION
IN ACCORDANCE WITH VSB
01
NO
INSTALLED BEFORE ON A
DIFFERENT AIRCRAFT?
SPARE WINDSHIELD
WAS THE
YES
YES
REPORT TO AIRBUS (MONITORED RETROFIT) 01
SEND THE WINDSHIELD INSPECTION
DO THE INSPECTION AGAIN
AT THE COMPLIANCE TIME DEFINED 01
NO
DO A CHECK OF THE PN OF A SPARE WINDSHIELD
BEFORE THE REPLACEMENT OF THE
01DAMAGED WINDSHIELD
01
WINDSHIELD WITH THE 
REPLACE THE DAMAGED
SPARE WINDSHIELD
01
WINDSHIELD WITH THE 
REPLACE THE DAMAGED
SPARE WINDSHIELD
A
B
AC
OR
NO
B
01
WITH VSB
REPAIR THE WEATHER SEAL IN ACCORDANCE
DO THE INSPECTIONS AGAIN
AT THE COMPLIANCE TIME DEFINED 01
ICN-A300-A-56XX0014-A-FAPE3-007GK-A-001-01

### Page 52

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IO-A-001-01 Fig.BA Sol.AA SHEET 1/2
REV 00 Nov 19/21 A300-56-0014Criteria of Delamination and Bubbles, LH side
Page 52
CONF ALL
INSPECTION AREA.
NOTE:
AREA WHERE THE DELAMINATION AND BUBBLES ARE PERMITTED.01
02 AREA WHERE THE DELAMINATION AND BUBBLES ARE NOT PERMITTED.
VIEW LOOKING AFT VIEW LOOKING AFT
75 mm
(2.953 in)
75 mm
(2.953 in)
A
A
20 mm
(0.787 in)
20 mm
(0.787 in)A
A
20 mm
(0.787 in)
A
AA
VIEW LOOKING AFT
01
02
B
FR1
FR11
Z211
A
ICN-A300-A-56XX0014-A-FAPE3-007IO-A-001-01

### Page 53

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IP-A-001-01 Fig.BA Sol.AA SHEET 2/2
REV 00 Nov 19/21 A300-56-0014Criteria of Delamination and Bubbles, LH side
Page 53
CONF ALL
A A
TYPICAL VIEW
20 mm
(0.787 in)
POSSIBLE LOCATIONS OF
DELAMINATION/BUBBLES
WEATHER SEAL
WINDSHIELD
TYPICAL VIEW
EXAMPLE OF DELAMINATION
AND BUBBLES FINDINGS
FROM OUTSIDE, USE A RULER TO MEASURE 03
THE WIDTH FROM THE WEATHER SEAL EDGE.
03
NOTE:
B
ICN-A300-A-56XX0014-A-FAPE3-007IP-A-001-01

### Page 54

A300
SERVICE BULLETIN
Figure ICN-A300-A-56XX0014-A-FAPE3-007IY-A-001-01 Fig.BI Sol.AA SHEET 1/1
REV 00 Nov 19/21 A300-56-0014Disconnection/Connection of the Front Windshield
Connector from the Aircraft Wiring, LH side Page 54
CONF ALL
EXAMPLE OF THE WINDSHIELD
HARNESS PLUG CONNECTED
TO THE WINDSHIELD CONNECTOR
VIEW LOOKING DOWN EXAMPLE OF THE WINDSHIELD
HARNESS PLUG DISCONNECTED
FROM THE WINDSHIELD CONNECTOR
VIEW LOOKING DOWN
A
F
W
D
F
W
D B
A B
ICN-A300-A-56XX0014-A-FAPE3-007IY-A-001-01

### Page 55

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 55
(2) Task A300-A-56-XX-0014-02001-311A-A (A300-A-56-XX-0014-02ZZZ-311Z-A)
Do the Inspection of the RH side Front Windshield
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
212
Manpower/Resources/Skills
Man-hours 1.10 h
Minimum Number of person 2
Elapsed Time 0.55 h
Skills Airframe
Material necessary to do the job
Aircraft standard tools
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
98D56003001000 1 WINDSHIE (1)
98D56003001001 1 HARNESS
98D56003001002 1 WINDSHIE (1)
NOTE(S)
(1): PN 98D56003001002 is alternative of the existing PN 98D56003001000.
Referenced Information
Manuals/Drawings References/Sheets
AMM
06-21-00, Page Block 001
20-16-00, Page Block 201
24-50-00, Page Block 001
30-42-00, Page Block 501
56-10-00, Page Block 901
ESPM 20-54-50
MMEL 1-30-9
NTM 51-40-00
VSB SAINT-GOBAIN (F0360) VSB SPSA340-56-001
Procedure
NOTE: This procedure is to be done only if the RH side front windshield installed on
aircraft is in Group 1, refer to Ref. T ask set A300-A-56-XX-0014-01ZZZ-93BZ-A.
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-21-00, Page Block 001.
2 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
3 For the circuit breaker safety practices, refer to Ref. AMM 20-16-00, Page
Block 201.

### Page 56

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 56
(b) Do the inspection of the RH side front windshield for Group 1, refer to Ref.
Fig.FD Flow Chart at the compliance time defined in accordance with PLANNING
INFORMATION paragraph 1.E. (2):
1 Do a detailed visual inspection of the RH side front windshield from
outside to detect delamination or bubbles, refer to Ref. Fig.BB Criteria of
Delamination and Bubbles, RH side:
a If delamination and/or bubbles are visible:
<1> At outboard edge:
<a> Record the findings in the inspection report sheet, refer to
Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
<b> Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to Ref. AMM
56-10-00, Page Block 901, and then fly under Ref.
MMEL 1-30-9
Or
- Do step (d) before next flight.
<2> At upper, inboard and lower edges, do a check for the width of
the delamination and/or bubbles from the weather seal around
the front windshield:
<a> If delamination and/or bubbles are above the criteria
defined in Ref. Fig.BB Criteria of Delamination and
Bubbles, RH side:
[1] Record the findings in the inspection report sheet,
refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
[2] Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to
Ref. AMM 56-10-00, Page Block 901, and then
fly under Ref. MMEL 1-30-9.
Or
- Do step (d) before next flight.
<b> If delamination and/or bubbles are not above the criteria
defined in Ref. Fig.BB Criteria of Delamination and
Bubbles, RH side:
[1] Record the findings in the inspection report sheet,
refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
[2] Do step (b)2.
b If delamination and/or bubbles are not visible:
<1> Record the nil finding in the inspection report sheet, refer to Ref.
T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
<2> Do step (b)2.
2 Do the operational test of the windshield anti-icing and defogging, refer to
Ref. AMM 30-42-00, Page Block 501:
a If fault found, use dedicated TSM.
WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE
WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.

### Page 57

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 57
3 Open, safety/lock and tag this (these) circuit breaker(s):
PANEL DESIGNATION FIN LOCATION SEE NOTES
ALT1/WINDSHIELDS/HEATERS/
FRONT
1DG
ALT2/WINDSHIELDS/HEATERS/
FRONT
2DG
FRONT WINDOW/RH/WARN/LT 4DG
FRONT WINDOW/RH/TEMP/REGUL 6DG
FRONT WINDOW/RH/PWR/CONTRL 8DG
RADIO NAV & COM/RADAR TR1 7SQ1
If installed, open, safety/lock and tag this circuit breaker:
PANEL DESIGNATION FIN LOCATION SEE NOTES
RADIO NAV & COM/RADAR TR2 7SQ2
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00, Page
Block 001.
4 Disconnect the windshield connector from the aircraft wiring, refer to Ref.
Fig.BJ Disconnection/Connection of the Front Windshield Connector from
the Aircraft Wiring, RH side.
5 Open the connector in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-311Z-A.
6 Do the detailed visual inspection of the connector in accordance with Ref.
SAINT-GOBAIN (F0360) VSB SPSA340-56-001 and refer to Ref. T ask A300-A-
56-XX-0014-03ZZZ-311Z-A:
NOTE: Record the result of inspection for all the connector visual
inspection steps in the Inspection Report sheet, refer to Ref. T ask
A300-A-56-XX-0014-03ZZZ-90AZ-A.
a If the connector cannot be opened for inspection:
<1> Close the connector in accordance with Ref. SAINT-GOBAIN
(F0360) VSB SPSA340-56-001 and refer to Ref. T ask A300-A-56-
XX-0014-03ZZZ-311Z-A.
<2> Connect the windshield connector to the aircraft wiring.
<3> Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to Ref. AMM 56-
10-00, Page Block 901, and then fly under Ref. MMEL 1-30-
9
Or
- Do step (d) before next flight.
b If the connector can be opened for inspection:
<1> Do a check for water ingress or corrosion in the windshield
connector:
NOTE: Refer to Ref. NTM 51-40-00 for using the recommended
endoscope or similar visual inspection aids.

### Page 58

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 58
<a> If water ingress or corrosion is found in the windshield
connector:
[1] Close the connector in accordance with Ref. SAINT-
GOBAIN (F0360) VSB SPSA340-56-001 and refer to
Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
[2] Connect the windshield connector to the aircraft
wiring.
[3] Fly under MMEL before next flight:
- Deactivate the windshield de-icing, refer to
Ref. AMM 56-10-00, Page Block 901, and then
fly under Ref. MMEL 1-30-9.
Or
- Do step (d) before next flight.
<b> If water ingress or corrosion is not found in the windshield
connector:
[1] Do step (b)7.
7 Close the connector in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-311Z-A.
8 Connect the windshield connector to the aircraft wiring, refer to Ref. Fig.BJ
Disconnection/Connection of the Front Windshield Connector from the
Aircraft Wiring, RH side.
9 Do the operational test of the windshield anti-icing and defogging, refer to
Ref. AMM 30-42-00, Page Block 501:
a If fault found, use dedicated TSM.
WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE
WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.
10 Open, safety/lock and tag this (these) circuit breaker(s):
PANEL DESIGNATION FIN LOCATION SEE NOTES
ALT1/WINDSHIELDS/HEATERS/
FRONT
1DG
ALT2/WINDSHIELDS/HEATERS/
FRONT
2DG
FRONT WINDOW/RH/WARN/LT 4DG
FRONT WINDOW/RH/TEMP/REGUL 6DG
FRONT WINDOW/RH/PWR/CONTRL 8DG
RADIO NAV & COM/RADAR TR1 7SQ1
If installed, open, safety/lock and tag this circuit breaker:
PANEL DESIGNATION FIN LOCATION SEE NOTES
RADIO NAV & COM/RADAR TR2 7SQ2
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00, Page
Block 001.

### Page 59

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 59
11 Disconnect the windshield connector from the aircraft wiring, refer to Ref.
Fig.BJ Disconnection/Connection of the Front Windshield Connector from
the Aircraft Wiring, RH side.
12 Do the dielectric test and then the insulation test, refer to Ref. Appendix
ELECTRICAL TESTS RESULT CHART:
a Remove a part of the weather seal over the metallic Z bar in
accordance with Ref. SAINT-GOBAIN (F0360) VSB SPSA340-56-001
and refer to Ref. T ask A300-A-56-XX-0014-03ZZZ-900Z-A.
WARNING: THE GSE TOOLS 98D56003001000, 98D56003001001
AND 98D56003001002 USE HIGH VOLTAGE DURING THE
TEST. BEFORE YOU START THE TEST, MAKE SURE THAT
ALL SAFETY PRECAUTIONS GIVEN IN THE TOOL USER
GUIDE ARE FOLLOWED. THE ELECTRICAL POWER IS
SUFFICIENTLY STRONG TO CAUSE AN INJURY OR KILL
YOU.
b Do the dielectric test (1500VAC during 1 minute) and insulation test
(500VDC during 1 minute), use tools:
1 WINDSHIELD
INSPECTION
98D56003001000  
or
1 WINDSHIELD
INSPECTION
98D56003001002  
and
1 HARNESS LR AND WB 98D56003001001  
NOTE: You must obey the instruction given in the GSE tool user
guide.
c Record the values in the inspection report sheet in accordance
with Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A and refer to Ref.
Appendix ELECTRICAL TESTS RESULT CHART.
d Connect the windshield connector to the aircraft wiring.
e Examine the color classification of the results of the dielectric and
insulation tests, refer to Ref. Appendix ELECTRICAL TESTS RESULT
CHART:
<1> If the electrical tests result is in red area:
<a> Do step (c) or (d) before next flight.
<2> If the electrical tests result is in green or amber area:
<a> Do step (d) or do the steps that follow:
[1] Do the operational test of the windshield anti-icing
and defogging, refer to Ref. AMM 30-42-00, Page
Block 501:
[a] If fault found, use dedicated TSM.
[2] Repair the weather seal in accordance with Ref.
SAINT-GOBAIN (F0360) VSB SPSA340-56-001 and
refer to Ref. T ask A300-A-56-XX-0014-01ZZZ-690Z-A.

### Page 60

A300
SERVICE BULLETIN
REV 00 Nov 19/21 A300-56-0014
Page 60
[3] Send the result to AIRBUS in accordance with Ref.
T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
[4] Do again the inspection of the RH side front
windshield for Group 1 at the compliance time
defined in accordance with PLANNING INFORMATION
paragraph 1.E.(2), refer to Ref. T ask A300-A-56-XX-
0014-01ZZZ-311Z-A.
(c) Do the operational test of the windshield anti-icing and defogging, refer to Ref.
AMM 30-42-00, Page Block 501 and Ref. Fig.FD Flow Chart at the compliance
time defined in accordance with PLANNING INFORMATION paragraph 1.E.(2).
1 If fault found, use dedicated TSM.
2 Repair the weather seal in accordance with Ref. SAINT-GOBAIN (F0360) VSB
SPSA340-56-001 and refer to Ref. T ask A300-A-56-XX-0014-01ZZZ-690Z-A.
3 Fly under MMEL:
- Deactivate the windshield de-icing, refer to Ref. AMM 56-10-00, Page
Block 901, and then fly under Ref. MMEL 1-30-9.
(d) Replace the damaged windshield with a spare windshield, refer to Ref. Fig.FD
Flow Chart at the compliance time defined in accordance with PLANNING
INFORMATION paragraph 1.E.(2):
1 If this Service Bulletin is not applicable for the PN of the spare windshield:
a Replace the damaged windshield with a spare windshield in
accordance with Ref. T ask set A300-A-56-XX-0014-01ZZZ-93CZ-A.
b Send the windshield inspection report to AIRBUS (Monitored retrofit)
in accordance with Ref. T ask A300-A-56-XX-0014-03ZZZ-90AZ-A.
c No further action is necessary with this Service Bulletin.
2 If this Service Bulletin is applicable for the PN of the spare windshield:
a Do a check if the spare windshield was installed before on a different
aircraft:
<1> If the spare windshield was not installed before on a different
aircraft:
<a> Replace the damaged windshield with a spare windshield
in accordance with Ref. T ask set A300-A-56-XX-0014-
01ZZZ-93CZ-A and refer to Ref. Fig.FD Flow Chart.
<b> Send the windshield inspection report to AIRBUS
(Monitored retrofit) in accordance with Ref. T ask A300-A-
56-XX-0014-03ZZZ-90AZ-A.
<c> Do again the inspection of the RH side front windshield
at the compliance time defined in accordance with
PLANNING INFORMATION paragraph 1.E.(2), refer to Ref.
T ask A300-A-56-XX-0014-02ZZZ-311Z-A.
<2> If the spare windshield was installed before on a different
aircraft:
NOTE: The shop inspection is not applicable to windshields in
shop and in stock, which have an Authorized Release
Certificate (ARC) (Form One) from SAINT-GOBAIN SULLY
with the indication “Outer ply replacement” with a total
of 0FH/0FC since new or repair.

The text continues at https://openairdocs.org/service-documents/airbus/a300-56-0014/file/8567b26b5b38.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
