# Airbus Service Bulletin A300-57-0256: No revision named

- Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2017-0554; AD 2018-17-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Airbus Service Bulletin A300-57-0256](https://openairdocs.org/service-documents/airbus/a300-57-0256.md)
- Title as filed: A300-57-0256 rev 00
- Pages: 75
- PDF: https://openairdocs.org/files/sha256/b1/ba/b1ba676f00a437acafe8af9745e6a112c4d06acf5261243f69035cd247985638
- Page: https://openairdocs.org/service-documents/airbus/a300-57-0256/file/b1ba676f00a4

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A300
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - CHANGES TO ALLOWABLE DAMAGE LIMITATIONS IN SRM
FOR A300-B2/B4/C4/F4
**CONF ALL
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Recent static analysis has shown that some areas of the A300 wing structure cannot sustain the
damage previously published in the A300 Structural Repair Manual (SRM). The SRM has been
amended to reduce the amount of damage permitted and indicate the areas of the wing structure where
damage is no longer permitted.
Operators will be required to check the areas identified in this Service Bulletin and compare against the
current SRM issue (including temporary revisions) to determine if the new requirements are met.
The accomplishment of this Service Bulletin will make sure that areas of the wing structure identified in
this Service Bulletin that have been damaged beyond the limits that are specified in the SRM are
identified and addressed.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 MANDATORY (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 YES
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 ETOPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
NOTE
 (1)
: Service Bulletin must be accomplished.
MATERIAL PRICE INFORMATION
No Material
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A300
SERVICE BULLETIN
SUMMARY
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
001 22P 81T ABR AFG CEL F2I IAW IRA IRM KZU MSR RUN
TIW TNO TSY
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
**CONF 001
Task 570256-839-895-001: Administrative
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
Task 570256-832-895-001: Inspection
TOTAL MANHOURS
 13.00
ELAPSED TIME (HOURS)
 13.00
**CONF 002
Task 570256-839-895-001: Administrative
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
Task 570256-832-895-001: Inspection
TOTAL MANHOURS
 11.00
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A300
SERVICE BULLETIN
SUMMARY
Task 570256-832-895-001: Inspection
ELAPSED TIME (HOURS)
 11.00
APPENDICES
**CONF ALL
None
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A300
SERVICE BULLETIN
SUMMARY
**CONF 001
A
A
LH SHOWN
RH SIMILAR
A
RIB4RIB5
RIB7
FRONT SPAR REAR SPAR
CENTER SPAR
RIB22
Z500
Z600
A_SB_570256_7_SAAA_01_00
NOTE:
AREA TO BE INSPECTED
Figure A-U SAAA - S heet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A300
SERVICE BULLETIN
SUMMARY
**CONF 002
A
A
LH SHOWN
RH SIMILAR
A
RIB5
RIB7
FRONT SPAR
REAR SPAR
CENTER SPAR
Z500
Z600
NOTE:
AREA TO BE INSPECTED
A_SB_570256_7_SAAB_01_01
Figure A-U SAAB - S heet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A300
SERVICE BULLETIN
SUMMARY
**CONF 001
A
A
LH SHOWN
RH SIMILAR
A
FRONT SPAR
Z500
Z600
RIB10
REAR SPAR
NOTE:
AREA TO BE INSPECTED
RIB13 RIB11
RIB12
A_SB_570256_7_SBAA_01_03
Figure A-U SBAA - S heet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A300
SERVICE BULLETIN
SUMMARY
**CONF 002
A
A
LH SHOWN
RH SIMILAR
A
FRONT SPAR
Z500
Z600
NOTE:
AREA TO BE INSPECTED
RIB10 RIB9
A_SB_570256_7_SBAB_01_02
Figure A-U SBAB - S heet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 7
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A300
SERVICE BULLETIN
SUMMARY
**CONF 001
A
A
LH SHOWN
RH SIMILAR
A
Z500
Z600
B
B
LH SHOWN
RH SIMILAR
B
NOTE:
AREA TO BE INSPECTED
A_SB_570256_7_SCAA_01_01
RIB15
RIB1
Figure A-USCAA - Sheet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 8
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A300
SERVICE BULLETIN
SUMMARY
**CONF 002
A
A
LH SHOWN
RH SIMILAR
A
Z500
Z600
B
B
LH SHOWN
RH SIMILAR
B
NOTE:
AREA TO BE INSPECTED
RIB15
A_SB_570256_7_SCAB_01_00
RIB29
Figure A-USCAB - Sheet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 9
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A300
SERVICE BULLETIN
SUMMARY
This Page Intentionally Left Blank
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 10
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A300
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - CHANGES TO ALLOWABLE DAMAGE LIMITATIONS IN SRM
FOR A300-B2/B4/C4/F4
MODIFICATION No.: None
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
(1) Models
B2-203 B2K-3C B4-103 B4-203 B4-2C C4-203 F4-203
(2) Effectivity by MSN
0045 0075 0080 0090 0105 0107 0117 0129 0139 0151-0152 0154 0157 0160 0173
0175 0180 0183 0185 0203 0210 0212 0218 0220 0226-0227 0234-0236 0239 0244
0247 0255-0256 0259 0261 0274 0277 0292 0299 0302
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
001
 0203 0218
22P
 0236
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 1
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A300
SERVICE BULLETIN
OPERATOR
 MSN
81T
 0157 0277 0292
ABR
 0152 0220 0259
AFG
 0180
CEL
 0212
F2I
 0235
IAW
 0239
IRA
 0080 0139 0151 0173 0185 0226 0256 0299 0302
IRM
 0090 0160 0175 0244
KZU
 0117
MSR
 0255
RUN
 0075 0105 0107 0154 0183
TIW
 0234 0261 0274
TNO
 0045 0210 0227 0247
TSY
 0129
(4) Configuration by MSN
MSN
 CONFIGURATION
0045 0075 0105 0107 0117 0129 0139 0151 0152 0154 0157
0173 0175 0180 0183 0203 0210 0212 0218 0220 0227 0234
0235 0236 0239 0247 0255 0256 0259 0261 0274 0277 0292
0299 0302
002
0080 0090 0160 0185 0226 0244
 001
(5) Configuration definition
**CONF 001
Config. 001 is valid for A300-B2 aircraft.
**CONF 002
Config. 002 is valid for A300-B4/C4/F4 aircraft.
(6) Material Effectivity
No Material Set
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
Recent static analysis has shown that some areas of the A300 wing structure cannot
sustain the damage previously published in the A300 Structural Repair Manual (SRM).
The SRM has been amended to reduce the amount of damage permitted and indicate
the areas of the wing structure where damage is no longer permitted.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 2
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A300
SERVICE BULLETIN
(2) Objective/Action
Operators will be required to check the areas identified in this Service Bulletin and
compare against the current SRM issue (including temporary revisions) to determine if
the new requirements are met.
(3) Advantages
The accomplishment of this Service Bulletin will make sure that areas of the wing
structure identified in this Service Bulletin that have been damaged beyond the limits
that are specified in the SRM are identified and addressed.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
NOTE
: Do an inspection of the aircraft records. If the aircraft records are not
complete or if SRM repairs have not been recorded, do an inspection of the
aircraft structure.
To accomplish this Service Bulletin it is necessary to :
**CONF 001
Task 570256-839-895-001: Administrative
(1) Do a Check of the Aircraft Records
Task 570256-832-895-001: Inspection
(1) Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT and Rib 22 on the LH Wing
(2) Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT and Rib 22 on the RH Wing
(3) Do a Detailed Inspection of the Front Spar between Ribs 10 and 13 and the Rear
Spar at Shroud Rib ABXZ 16.3 on the LH Wing
(4) Do a Detailed Inspection of the Front Spar between Ribs 10 and 13 and the Rear
Spar at Shroud Rib ABXZ 16.3 on the RH Wing
(5) Do a Detailed Inspection of the Top Skin between Ribs 1 and 29 and the Bottom
Wing Skin between Ribs 1 and 15 on the LH Wing
(6) Do a Detailed Inspection of the Top Skin between Ribs 1 and 29 and the Bottom
Wing Skin between Ribs 1 and 15 on the RH Wing
**CONF 002
Task 570256-839-895-001: Administrative
(1) Do a Check of the Aircraft Records
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 3
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A300
SERVICE BULLETIN
Task 570256-832-895-001: Inspection
(1) Do a Detailed Inspection of Ribs 5 AFT and 7 AFT on the LH Wing
(2) Do a Detailed Inspection of Ribs 5 AFT and 7 AFT on the RH Wing
(3) Do a Detailed Inspection of the Front Spar between Ribs 9 and 10 on the LH Wing
(4) Do a Detailed Inspection of the Front Spar between Ribs 9 and 10 on the RH Wing
(5) Do a Detailed Inspection of the Top Skin between Ribs 1 and 29 and the Bottom
Wing Skin between Ribs 15 and 29 on the LH Wing
(6) Do a Detailed Inspection of the Top Skin between Ribs 1 and 29 and the Bottom
Wing Skin between Ribs 15 and 29 on the RH Wing
**CONF ALL
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Within 4 years from issue of this Inspection Service Bulletin.
This Service Bulletin has been classified Mandatory. It is expected that an Airworthiness
Directive (AD) published by the European Av iation Safety Agenc y (EASA) will be issued
to confirm this classification. It is anticipated that the AD will confirm the compliance time
given above but reference should be made to the AD for confirmation of the mandated
accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approv al No. EASA. 21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 4
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A300
SERVICE BULLETIN
**CONF 001
Task 570256-839-895-001: Administrative
On Aircraft
Do a Check of the Aircraft Records
 1.00
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
Task 570256-832-895-001: Inspection
Get Access
 2.00
On Aircraft
Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT
and Rib 22 on the LH Wing
1.50
Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT
and Rib 22 on the RH Wing
1.50
Do a Detailed Inspection of the Front Spar between
Ribs 10 and 13 and the Rear Spar at Shroud Rib
ABXZ 16.3 on the LH Wing
1.50
Do a Detailed Inspection of the Front Spar between
Ribs 10 and 13 and the Rear Spar at Shroud Rib
ABXZ 16.3 on the RH Wing
1.50
Do a Detailed Inspection of the Top Skin between Ribs
1 and 29 and the Bottom Wing Skin between Ribs 1
and 15 on the LH Wing
1.50
Do a Detailed Inspection of the Top Skin between Ribs
1 and 29 and the Bottom Wing Skin between Ribs 1
and 15 on the RH Wing
1.50
Close-Up
 2.00
TOTAL MANHOURS
 13.00
ELAPSED TIME (HOURS)
 13.00
NOTE
: The minimum manhours necessary to accomplish this Service Bulletin are
those for the Inspection. Depending on the inspection result, additional
manhours can apply.
**CONF 002
Task 570256-839-895-001: Administrative
On Aircraft
Do a Check of the Aircraft Records
 1.00
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
Task 570256-832-895-001: Inspection
Get Access
 1.00
On Aircraft
Do a Detailed Inspection of Ribs 5 AFT and 7 AFT on
the LH Wing
1.50
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 5
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A300
SERVICE BULLETIN
Task 570256-832-895-001: Inspection
Do a Detailed Inspection of Ribs 5 AFT and 7 AFT on
the RH Wing
1.50
Do a Detailed Inspection of the Front Spar between
Ribs 9 and 10 on the LH Wing
1.50
Do a Detailed Inspection of the Front Spar between
Ribs 9 and 10 on the RH Wing
1.50
Do a Detailed Inspection of the Top Skin between Ribs
1 and 29 and the Bottom Wing Skin between Ribs 15
and 29 on the LH Wing
1.50
Do a Detailed Inspection of the Top Skin between Ribs
1 and 29 and the Bottom Wing Skin between Ribs 15
and 29 on the RH Wing
1.50
Close-Up
 1.00
TOTAL MANHOURS
 11.00
ELAPSED TIME (HOURS)
 11.00
NOTE
: The minimum manhours necessary to accomplish this Service Bulletin are
those for the Inspection. Depending on the inspection result, additional
manhours can apply.
**CONF ALL
H. WEIGHT AND BALANCE
Not Changed
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
**CONF 001
Aircraft Maintenance Manual (AMM)
 06-21-00 06-21-57 20-16-00
24-00-00 28-11-14
Elec. Std. Practices Manual (ESPM)
 20-55-00
Structural Repair Manual (SRM)
 57-11-11 57-12-11 57-33-11
**CONF 002
Aircraft Maintenance Manual (AMM)
 06-21-00 06-21-57 20-16-00
24-00-00 28-11-14
Elec. Std. Practices Manual (ESPM)
 20-55-00
Structural Repair Manual (SRM)
 57-11-11 57-12-11 57-12-12
57-33-11 57-33-12
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 6
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A300
SERVICE BULLETIN
**CONF ALL
K. PUBLICATION AFFECTED
**CONF 001
Structural Repair Manual (SRM)
 57-11-11 57-12-11 57-33-11
**CONF 002
Structural Repair Manual (SRM)
 57-12-12 57-33-11
**CONF ALL
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 7
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A300
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 8
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A300
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
No Material Set
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not credit the manhours indicated in this Service Bulletin. They remain at
operator’s charge.
C. LIST OF COMPONENTS
No Kit
D. LIST OF MATERIALS - OPERATOR SUPPLIED
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
F. TOOLING
None
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 9
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A300
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 10
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A300
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 570256-839-895-001 - Administrative
NOTE
: This Service Bulletin must be accomplished by a check of the aircraft records
and/or by inspection of the aircraft.
If the aircraft records are missing or are not complete, do the detailed inspection
procedure of the wing structure to make sure that no damage exists beyond that
allowed in the current revision of the SRM (including temporary revisions).
If aircraft records are complete, in accordance with the current revision of the SRM,
there is no need to visit the aircraft.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
Task Associated Data
**CONF 001
Manpower
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
**CONF 002
Manpower
TOTAL MANHOURS
 1.00
ELAPSED TIME (HOURS)
 1.00
**CONF ALL
A. GENERAL
**CONF 001
None
**CONF 002
None
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 11
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A300
SERVICE BULLETIN
**CONF ALL
B. PREPARATION
**CONF 001
None
**CONF 002
None
**CONF ALL
C. PROCEDURE
**CONF 001
(1) Subtask 570256-839-403-001 - Do a Check of the Aircraft Records
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 NON SPECIFIC
References
Structural Repair Manual (SRM)
 57-11-11
57-12-11
57-33-11
Fig. A-UBAAA
Detailed Inspection of Ribs 4 FWD, 5
AFT, 7 AFT and 22
Sheet 01
Sheet 02
Sheet 03
Fig. A-UBCAA
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Fig. A-UBBAA
Detailed Inspection of the Front and
Rear Spar
Sheet 01
Sheet 02
(a) Do a check of the aircraft records against the following SRM sections to make sure
that the existing repairs (if any) are within the new limits identified within the current
revision of the SRM (including temporary revisions):
Figure reference of Figures
in this Service Bulletin
SRM reference (ATA
chapter)
Area Affected
Fig. A-UBAAA Sheet 02
 SRM 57-12-11
 Rib 4 Fwd
Fig. A-UBAAA Sheet 02
 SRM 57-12-11
 Rib 5 Aft
Fig. A-UBAAA Sheet 03
 SRM 57-12-11
 Rib 7 Aft
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 12
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A300
SERVICE BULLETIN
Figure reference of Figures
in this Service Bulletin
SRM reference (ATA
chapter)
Area Affected
Fig. A-UBAAA Sheet 03
 SRM 57-12-11
 Rib 22
Fig. A-UBCAA Sheet 02
 SRM 57-33-11
 Top Skin (Ribs 1 to 15)
Fig. A-UBCAA Sheet 02
 SRM 57-33-11
 Top Skin (Ribs 15 to 29)
Fig. A-UBCAA Sheet 03
 SRM 57-33-11
 Bottom Skin (Ribs 1 to 15)
Fig. A-UBCAA Sheet 02
 SRM 57-11-11
 Front Spar (Ribs 10 to 13)
Fig. A-UBCAA Sheet 02
 SRM 57-11-11
 Rear Spar (Rib 11 to 12) ABXZ 16.3
1
 If the aircraft records are missing or not complete, in accordance with the
current revision of the SRM, go to TASK 570256-832-895 001 Inspection .
2
 If identified repairs are beyond the current SRM limits, contact AIRBUS within
3 months after you have completed this inspection.
3
 If identified repairs are within the current SRM limits, no further maintenance
steps are necessary.
**CONF 002
(1) Subtask 570256-839-403-002 - Do a Check of the Aircraft Records
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 NON SPECIFIC
References
Structural Repair Manual (SRM)
 57-11-11
57-12-12
57-33-11
Fig. A-UBAAB
Detailed Inspection of Ribs 5 AFT and 7
AFT
Sheet 01
Sheet 02
Fig. A-UBBAB
Detailed Inspection of the Front Spar
Top Boom
Sheet 01
Fig. A-UBCAB
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 13
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A300
SERVICE BULLETIN
(a) Do a check of the aircraft records against the following SRM sections to make sure
that the existing repairs (if any) are within the new limits identified within the current
revision of the SRM (including temporary revisions):
Figure reference of Figures in
this Service Bulletin
SRM reference
(ATA chapter)
Area Affected
Fig. A-UBAAB Sheet 02
 SRM 57-12-12
 Rib 5 Aft
Fig. A-UBAAB Sheet 02
 SRM 57-12-12
 Rib 7 Aft
Fig. A-UBCAB Sheet 02
 SRM 57-33-11
 T o pS k i n( R i b s1t o1 5 )
Fig. A-UBCAB Sheet 02
 SRM 57-33-11
 Top Skin (Ribs 15 to 29)
Fig. A-UBCAB Sheet 03
 SRM 57-33-11
 Bottom Skin (Ribs 15 to 29)
Fig. A-UBCAB Sheet 01
 SRM 57-11-11
 Front Spar (Ribs 9 to 10)
1
 If the aircraft records are missing or not complete, in accordance with the
current revision of the SRM, go to TASK 570256-832-895 001 Inspection .
2
 If identified repairs are beyond the current SRM limits, contact AIRBUS within
3 months after you have completed this inspection.
3
 If identified repairs are within the current SRM limits, no further maintenance
steps are necessary.
**CONF ALL
D. TEST
**CONF 001
None
**CONF 002
None
**CONF ALL
E. CLOSE-UP
**CONF 001
None
**CONF 002
None
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 14
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A300
SERVICE BULLETIN
Task 570256-832-895-001 - Inspection
**CONF ALL
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION
(CDCCL) CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A
POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN
THE APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A
CDCCL ITEM CAN CAUSE A POSSIBLE FUEL TANK EXPLOSION.
WARNING
: BEFORE YOU DO WORK IN A FUEL TANK, MAKE SURE THAT YOU OBEY
ALL THE SAFETY PROCEDURES. THIS WILL PREVENT INJURY TO PERSONS
AND/OR DAMAGE TO THE AIRCRAFT.
WARNING
: USE THE APPROVED PR OTECTIVE CLOTHING WHEN YOU GO IN A FUEL
TANK. THIS PREVENTS PERSONAL CONTAMINATION AND THE FORMATION
OF STATIC ELECTRICITY.
WARNING
: OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
THIS WILL PREVENT INJURY OR DAMAGE.
WARNING
: DO NOT REMOVE YOUR RESPIRATOR WHILE YOU ARE IN A FUEL TANK
(UNLESS THE FUEL-GAS CONCENTRATION IS LESS THAN 5% OF LEL
(LOWER EXPLOSIVE LIMIT)). YOU WILL BECOME ILL OR DIE.
WARNING
: DO NOT GO INTO A FUEL TANK UNTIL THE FUEL-GAS CONCENTRATION
IS LESS THAN 10% OF LEL (LOWER EXPLOSIVE LIMIT) OR THE LOCAL
REGULATORY-AUTHORITY LIMIT.
WARNING
: YOU MUST ISOLATE THE AIRCRAFT BATTERIES AND THE ELECTRICAL
GROUND- POWER SUPPLY WHEN A FUEL TANK IS OPEN. THIS CAN
PREVENT AN EXPLOSION.
WARNING
: ALWAYS PUT ON AN APPROVED RESPIRATOR AND PROTECTIVE
CLOTHING BEFORE YOU GO INTO A FUEL TANK THAT HAS MICROBIAL
CONTAMINATION. IF YOU BREATHE IN OR TOUCH THE MICROBIAL
GROWTH, THERE CAN BE A HEALTH RISK.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 15
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A300
SERVICE BULLETIN
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC; AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: This Service Bulletin must be accomplished by a check of the aircraft records
and/or by inspection of the aircraft.
If the aircraft records are missing or are not complete, do the detailed inspection
procedure of the wing structure to make sure that no damage exists beyond that
allowed in the current revision of the SRM (including temporary revisions).
If aircraft records are complete, in accordance with the current revision of the SRM,
there is no need to visit the aircraft.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
"refer to" are used and the operator has a procedure accepted by the local
authority he belongs to, the accepted alternative procedure can be used. When the
words "in accordance with" are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: The purpose of flow charts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 16
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A300
SERVICE BULLETIN
the aircraft can be put back into a serviceable condition.
Task Associated Data
**CONF 001
Zone
500 520 540 550 600 620 640 650
Access
Panel
 523CB 523DB 523EB 523FB 523HB 523JB 541AB 541BB
542CB 542DB 542EB 543AB 543BB 543CB 543DB 550KB
550LB 581CB 581DB 581EB 581FB 581GB 623CB 623DB
623EB 623FB 623HB 623JB 641AB 641BB 642CB 642DB
642EB 643AB 643BB 643CB 643DB 650KB 650LB 681CB
681DB 681EB 681FB 681GB
Manpower
TOTAL MANHOURS
 13.00
ELAPSED TIME (HOURS)
 13.00
**CONF 002
Zone
500 520 540 550 600 620 640 650
Access
Panel
 523CB 523DB 523EB 523FB 523HB 523JB 541AB 541BB
542CB 542DB 542EB 543AB 543BB 543CB 543DB 550KB
550LB 581CB 581DB 581EB 581FB 581GB 623CB 623DB
623EB 623FB 623HB 623JB 641AB 641BB 642CB 642DB
642EB 643AB 643BB 643CB 643DB 650KB 650LB 681CB
681DB 681EB 681FB 681GB
Manpower
TOTAL MANHOURS
 11.00
ELAPSED TIME (HOURS)
 11.00
**CONF ALL
A. GENERAL
**CONF 001
(1) Subtask 570256-910-401-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-57, Page Block 001
20-16-00, Page Block 201
(a) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 17
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A300
SERVICE BULLETIN
(b) For the identification of the wing access panels, refer to AMM 06-21-57, Page Block
001.
(c) For circuit breaker safety precautions, refer to AMM 20-16-00, Page Block 201.
(2) Subtask 570256-839-401-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 002
(1) Subtask 570256-910-401-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-21-57, Page Block 001
20-16-00, Page Block 201
(a) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(b) For the identification of the wing access panels, refer to AMM 06-21-57, Page Block
001.
(c) For circuit breaker safety precautions, refer to AMM 20-16-00, Page Block 201.
(2) Subtask 570256-839-401-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 18
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A300
SERVICE BULLETIN
**CONF ALL
B. PREPARATION
**CONF 001
(1) Subtask 570256-941-401-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 542EB, Panel 543AB, Panel 543BB, Panel
543CB, Panel 543DB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 10 to Rib 13
from Rib 11 to Rib 13
Rib 4 FWD
640
 Access
 Panel 642EB, Panel 643AB, Panel 643BB, Panel
643CB, Panel 643DB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 10 to Rib 13
from Rib 11 to Rib 13
Rib 4 FWD
550
 Access
 Panel 550LB, Panel 550KB
Work location
 Rib 22
650
 Access
 Panel 650LB, Panel 650KB
Work location
 Rib 22
500
 Work location
 from Rib 1 to Rib 29
600
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
28-11-14, Page Block 401
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 19
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A300
SERVICE BULLETIN
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Put a WARNING NOTICE in position in the cockpit to tell persons not to operate
the flight controls.
(b) Put an access platform in position to get access to the wing.
(c) Install the safety barriers.
(d) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(e) Do the job set-up procedures as specified in the ’Removal/Installation of the
Manhole Covers’, refer to AMM 28-11-14, Page Block 401.
(2) Subtask 570256-010-401-001 - Remove/Open for Access
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 541AB, Panel 541BB, Panel 542DB,
Panel 542CB, Panel 542EB, Panel 543AB,
Panel 543BB, Panel 543CB, Panel 581CB,
Panel 581DB, Panel 581EB, Panel 581FB, Panel
581GB, Panel 543DB
Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
640
 Access
 Panel 641AB, Panel 641BB, Panel 642CB,
Panel 642DB, Panel 642EB, Panel 681CB,
Panel 681DB, Panel 681EB, Panel 681FB, Panel
681GB, Panel 643AB, Panel 643BB, Panel
643CB, Panel 643DB
Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
550
 Access
 Panel 550LB, Panel 550KB
Work location
 Rib 22
650
 Access
 Panel 650LB, Panel 650KB
Work location
 Rib 22
520
 Access
 Panel 523CB, Panel 523DB, Panel 523EB,
Panel 523FB, Panel 523HB, Panel 523JB
620
 Access
 Panel 623CB, Panel 623DB, Panel 623EB,
Panel 623FB, Panel 623HB, Panel 623JB
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 20
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A300
SERVICE BULLETIN
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Remove (as necessary) the panels that follow to get access to rib 4 FWD, refer to
AMM 28-11-14, Page Block 401:
- 541AB, 641AB, 541BB and 641BB.
(b) Remove (as necessary) the panels that follow to get access to rib 5 AFT and rib 7
AFT, refer to AMM 28-11-14, Page Block 401:
- 542CB, 542DB, 642DB and 642CB.
(c) Remove (as necessary) the panels that follow to get access to rib 22, refer to AMM
28-11-14, Page Block 401:
- 550LB, 650LB, 550KB and 650KB.
(d) Remove (as necessary) the panels that follow to get access to the front spar at rib
10 to 13, refer to AMM 28-11-14, Page Block 401:
1
 FWD of the front spar, remove:
- 523CB, 623CB, 523DB, 623DB, 523EB, 623EB, 523FB, 623FB, 523HB,
623HB, 523JB and 623JB.
2
 AFT of the front spar, remove:
- 542EB, 642EB, 543AB, 643AB, 543BB, 643BB, 543CB, 643CB, 543DB
and 643DB.
(e) Make sure that the panels that follow are removed, to get access to the rear spar at
rib 9 to 13, refer to AMM 28-11-14, Page Block 401:
1
 AFT of the rear spar, remove:
- 581CB, 681CB, 581DB, 681DB, 581EB, 681EB, 581FB, 681FB, 581GB
and 681GB.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 21
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A300
SERVICE BULLETIN
**CONF 002
(1) Subtask 570256-941-401-003 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 542EB, Panel 543AB, Panel 543BB, Panel
543CB, Panel 543DB, Panel 541AB, Panel
541BB, Panel 542DB, Panel 542CB, Panel
581DB, Panel 581EB, Panel 581FB, Panel
581GB, Panel 523EB, Panel 523FB, Panel
523HB, Panel 523JB, Panel 523CB, Panel
523DB, Panel 581CB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
640
 Access
 Panel 642EB, Panel 643AB, Panel 643BB, Panel
643CB, Panel 643DB, Panel 641AB, Panel
641BB, Panel 642DB, Panel 642CB, Panel
681DB, Panel 681EB, Panel 681FB, Panel
681GB, Panel 623EB, Panel 623FB, Panel
623HB, Panel 623JB, Panel 623CB, Panel
623DB, Panel 681CB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
550
 Access
 Panel 550LB, Panel 550KB
Work location
 Rib 22
650
 Access
 Panel 650LB, Panel 650KB
Work location
 Rib 22
500
 Work location
 from Rib 1 to Rib 29
600
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
28-11-14, Page Block 401
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 22
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A300
SERVICE BULLETIN
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Put a WARNING NOTICE in position in the cockpit to tell persons not to operate
the flight controls.
(b) Put an access platform in position to get access to the wing.
(c) Install the safety barriers.
(d) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(e) Do the job set-up procedures as specified in the ’Removal/Installation of the
Manhole Covers’, refer to AMM 28-11-14, Page Block 401.
(2) Subtask 570256-010-401-002 - Remove/Open for Access
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 542CB, Panel 542EB, Panel 543AB,
Panel 543BB, Panel 543CB, Panel 543DB
Work location
 Rib 5AFT
Rib 7AFT
from Rib 9 to Rib 10
640
 Access
 Panel 642CB, Panel 642EB, Panel 643AB,
Panel 643BB, Panel 643CB, Panel 643DB
Work location
 Rib 5AFT
Rib 7AFT
from Rib 9 to Rib 10
520
 Access
 Panel 523CB, Panel 523DB, Panel 523EB,
Panel 523FB, Panel 523HB, Panel 523JB
620
 Access
 Panel 623CB, Panel 623DB, Panel 623EB,
Panel 623FB, Panel 623HB, Panel 623JB
Manpower Resources
Skills
 AIRFRAME
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Remove (as necessary) the panels that follow to get access to rib 5 AFT and rib 7
AFT, refer to AMM 28-11-14, Page Block 401:
- 542CB and 642CB.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 23
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A300
SERVICE BULLETIN
(b) Remove (as necessary) the panels that follow to get access to the front spar at rib
9 to 10, refer to AMM 28-11-14, Page Block 401:
1
 FWD of the front spar, remove:
- 523CB, 623CB, 523DB, 623DB, 523EB, 623EB, 523FB, 623FB, 523HB,
623HB, 523JB and 623JB.
2
 AFT of the front spar, remove:
- 542EB, 642EB, 543AB, 643AB, 543BB, 643BB, 543CB, 643CB, 543DB
and 643DB.
**CONF ALL
C. PROCEDURE
**CONF 001
(1) Subtask 570256-832-401-001 - Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7
AFT and Rib 22 on the LH Wing
Work Zones and Access Panels
Zone
 Access/Work location
540
 Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
Rib 22
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-12-11
Fig. A-UBAAA
Detailed Inspection of Ribs 4 FWD, 5
AFT, 7 AFT and 22
Sheet 01
Sheet 02
Sheet 03
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the ribs that follow, do a detailed inspection for damage that is outside of the
limits specified in the current revision of the SRM.
1
 At rib 4 FWD, do a detailed inspection for damage in the areas shown on Fig.
A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 02
 , View B, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 24
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A300
SERVICE BULLETIN
- If there is no damage, and no repairs that are outside the limits set in the
SRM, at the areas 1, 2 and 3 shown, no further action is required at this
rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months after you have completed this
inspection (Refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in areas 1, 2 and 3, including on the free edges of the flanges bordering
these areas, contact AIRBUS within 3 months after you have completed
this inspection.
2
 At rib 5 AFT, do a detailed inspection for damage in the area shown on Fig. A-
UBAAA S heet 01
 and Fig. A-UBAAA Sheet 02
 , View C, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, at the area 1 shown, no further action is required at this rib
- If there is a repair that is outside of the limits set in the current revision of
the SRM (including temporary revisions) that can be replaced, after the
repair survey replace the repair in accordance with an applicable current
SRM repair, or another approved repair within 3 months after you have
completed this inspection (refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 25
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A300
SERVICE BULLETIN
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
3
 At rib 7 AFT, do a detailed inspection for damage on the stringers shown on
Fig. A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 03
 , View D, in accordance
with SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, at the stiffener at area 1 shown, no further action is required at this
rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months after you have completed this
inspection (Refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
4
 At rib 22, do a detailed inspection for damage in the area at area 1, shown on
Fig. A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 03
 , View E, in accordance
with SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 26
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A300
SERVICE BULLETIN
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
(2) Subtask 570256-832-404-001 - Do a Detailed Inspection of Ribs 4 FWD, 5 AFT, 7
AFT and Rib 22 on the RH Wing
Work Zones and Access Panels
Zone
 Access/Work location
640
 Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
Rib 22
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-12-11
Fig. A-UBAAA
Detailed Inspection of Ribs 4 FWD, 5
AFT, 7 AFT and 22
Sheet 01
Sheet 02
Sheet 03
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the ribs that follow, do a detailed inspection for damage that is outside of the
limits specified in the current revision of the SRM.
1
 At rib 4 FWD, do a detailed inspection for damage in the areas shown on Fig.
A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 02
 , View B, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 27
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A300
SERVICE BULLETIN
- If there is no damage, and no repairs that are outside the limits set in the
SRM, at the areas 1, 2 and 3 shown, no further action is required at this
rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months after you have completed this
inspection (Refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in areas 1, 2 and 3, including on the free edges of the flanges bordering
these areas, contact AIRBUS within 3 months after you have completed
this inspection.
2
 At rib 5 AFT, do a detailed inspection for damage in the area shown on Fig. A-
UBAAA S heet 01
 and Fig. A-UBAAA Sheet 02
 , View C, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, at the area 1 shown, no further action is required at this rib
- If there is a repair that is outside of the limits set in the current revision of
the SRM (including temporary revisions) that can be replaced, after the
repair survey replace the repair in accordance with an applicable current
SRM repair, or another approved repair within 3 months after you have
completed this inspection (refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 28
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A300
SERVICE BULLETIN
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
3
 At rib 7 AFT, do a detailed inspection for damage on the stringers shown on
Fig. A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 03
 , View D, in accordance
with SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, at the stiffener at area 1 shown, no further action is required at this
rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months after you have completed this
inspection (Refer to Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
4
 At rib 22, do a detailed inspection for damage in the area at area 1, shown on
Fig. A-UBAAA Sheet 01
 and Fig. A-UBAAA Sheet 03
 , View E, in accordance
with SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 29
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A300
SERVICE BULLETIN
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
(3) Subtask 570256-832-403-001 - Do a Detailed Inspection of the Front Spar between
Ribs 10 and 13 and the Rear Spar at Shroud Rib ABXZ 16.3 on the LH Wing
Work Zones and Access Panels
Zone
 Access/Work location
540
 Work location
 from Rib 10 to Rib 13
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-11-11
Fig. A-UBBAA
Detailed Inspection of the Front and
Rear Spar
Sheet 01
Sheet 02
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the front and rear spar, do a detailed inspection for damage as specified in the
current revision of the SRM.
1
 On the front spar, at ribs 10 thru 13, do a detailed inspection for damage as
shown on Fig. A-UBBAA Sheet 01
 and Fig. A-UBBAA Sheet 02
 ,V i e wBa n d
Section A-A, in accordance with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 30
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A300
SERVICE BULLETIN
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced and any damage as shown in Section A-A, contact AIRBUS
within 3 months of this inspection.
2
 On the rear spar, at shroud rib Stn. ABXZ 16.3 between ribs 11 and 12, do a
detailed inspection for damage as shown on Fig. A-UBBAA Sheet 01
 and Fig.
A-UBBAA Sheet 02
 , View C, in accordance with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
(4) Subtask 570256-832-405-001 - Do a Detailed Inspection of the Front Spar between
Ribs 10 and 13 and the Rear Spar at Shroud Rib ABXZ 16.3 on the RH Wing
Work Zones and Access Panels
Zone
 Access/Work location
640
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-11-11
Fig. A-UBBAA
Detailed Inspection of the Front and
Rear Spar
Sheet 01
Sheet 02
Fig. A-UFAAA
Flowchart
Sheet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 31
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A300
SERVICE BULLETIN
(a) On the front and rear spar, do a detailed inspection for damage as specified in the
current revision of the SRM.
1
 On the front spar, at ribs 10 thru 13, do a detailed inspection for damage as
shown on Fig. A-UBBAA Sheet 01
 and Fig. A-UBBAA Sheet 02
 ,V i e wBa n d
Section A-A, in accordance with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced and any damage as shown in Section A-A, contact AIRBUS
within 3 months of this inspection.
2
 On the rear spar, at shroud rib Stn. ABXZ 16.3 between ribs 11 and 12, do a
detailed inspection for damage as shown on Fig. A-UBBAA Sheet 01
 and Fig.
A-UBBAA Sheet 02
 , View C, in accordance with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
(5) Subtask 570256-832-402-001 - Do a Detailed Inspection of the Top Skin between
Ribs 1 and 29 and the Bottom Wing Skin between Ribs 1 and 15 on the LH Wing
Work Zones and Access Panels
Zone
 Access/Work location
500
 Work location
 from Rib 1 to Rib 29
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 32
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A300
SERVICE BULLETIN
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-33-11
Fig. A-UBCAA
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the top and bottom wing skin, do a detailed inspection for damage that is
outside of the limits specified in the current revision of the SRM, refer to Fig. A-
UBCAA Sheet 01
 , Fig. A-UBCAA Sheet 02
 ,V i e wC .a n d Fig. A-UBCAA Sheet 03
 ,
View D.
1
 On the bottom wing skin between ribs 1 thru 15, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
2
 On the top wing skin between ribs 1 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 33
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A300
SERVICE BULLETIN
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
(6) Subtask 570256-832-406-001 - Do a Detailed Inspection of the Top Skin between
Ribs 1 and 29 and the Bottom Wing Skin between Ribs 1 and 15 on the RH Wing
Work Zones and Access Panels
Zone
 Access/Work location
600
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-33-11
Fig. A-UBCAA
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the top and bottom wing skin, do a detailed inspection for damage that is
outside of the limits specified in the current revision of the SRM, refer to Fig. A-
UBCAA Sheet 01
 , Fig. A-UBCAA Sheet 02
 ,V i e wC .a n d Fig. A-UBCAA Sheet 03
 ,
View D.
1
 On the bottom wing skin between ribs 1 thru 15, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
2
 On the top wing skin between ribs 1 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 34
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A300
SERVICE BULLETIN
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
**CONF 002
(1) Subtask 570256-832-401-002 - Do a Detailed Inspection of Ribs 5 AFT and 7 AFT
on the LH Wing
Work Zones and Access Panels
Zone
 Access/Work location
540
 Work location
 Rib 5 AFT
Rib 7 AFT
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-12-11
57-12-12
57-33-12
Fig. A-UBAAB
Detailed Inspection of Ribs 5 AFT and 7
AFT
Sheet 01
Sheet 02
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the ribs that follow, do a detailed inspection for damage in accordance with the
current revision of the SRM.
1
 At rib 5 AFT, do a detailed inspection for damage at area 1, shown on Fig. A-
UBAAB S heet 01
 and Fig. A-UBAAB Sheet 02
 , View B, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 35
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A300
SERVICE BULLETIN
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
2
 At rib 7 AFT, do a detailed inspection for damage in the areas shown at areas
1, 2 and 3 on Fig. A-UBAAB Sheet 01
 and Fig. A-UBAAB Sheet 02
 ,V i e wC ,
in accordance with SRM 57-12-12.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 36
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A300
SERVICE BULLETIN
(2) Subtask 570256-832-404-002 - Do a Detailed Inspection of Ribs 5 AFT and 7 AFT
on the RH Wing
Work Zones and Access Panels
Zone
 Access/Work location
640
 Work location
 Rib 5 AFT
Rib 7 AFT
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-12-11
57-12-12
57-33-12
Fig. A-UBAAB
Detailed Inspection of Ribs 5 AFT and 7
AFT
Sheet 01
Sheet 02
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the ribs that follow, do a detailed inspection for damage in accordance with the
current revision of the SRM.
1
 At rib 5 AFT, do a detailed inspection for damage at area 1, shown on Fig. A-
UBAAB S heet 01
 and Fig. A-UBAAB Sheet 02
 , View B, in accordance with
SRM 57-12-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 37
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A300
SERVICE BULLETIN
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
2
 At rib 7 AFT, do a detailed inspection for damage in the areas shown at areas
1, 2 and 3 on Fig. A-UBAAB Sheet 01
 and Fig. A-UBAAB Sheet 02
 ,V i e wC ,
in accordance with SRM 57-12-12.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there are any:
. repairs outside of the limits set in the SRM
. scores
. scratches
. abrasions
. or corrosion
in area 1, including on the free edges of the flanges bordering these
areas, contact AIRBUS within 3 months after you have completed this
inspection.
(3) Subtask 570256-832-403-002 - Do a Detailed Inspection of the Front Spar between
R i b s9a n d1 0o nt h eL HW i n g
Work Zones and Access Panels
Zone
 Access/Work location
540
 Work location
 from Rib 9 to Rib 10
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 38
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A300
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 57-11-11
Fig. A-UBBAB
Detailed Inspection of the Front Spar
Top Boom
Sheet 01
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the front spar, do a detailed inspection for damage in accordance with the
current revision of the SRM.
1
 On the front spar, at ribs 9 thru 10, do a detailed inspection for damage as
shown on Fig. A-UBBAB Sheet 01
 , View B and Section A-A, in accordance
with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, or any damage as shown in Section A-A, contact AIRBUS
within 3 months of this inspection.
(4) Subtask 570256-832-405-002 - Do a Detailed Inspection of the Front Spar between
R i b s9a n d1 0o nt h eR HW i n g
Work Zones and Access Panels
Zone
 Access/Work location
640
 Work location
 from Rib 10 to Rib 13
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-11-11
Fig. A-UBBAB
Detailed Inspection of the Front Spar
Top Boom
Sheet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 39
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A300
SERVICE BULLETIN
References
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the front spar, do a detailed inspection for damage in accordance with the
current revision of the SRM.
1
 On the front spar, at ribs 9 thru 10, do a detailed inspection for damage as
shown on Fig. A-UBBAB Sheet 01
 , View B and Section A-A, in accordance
with SRM 57-11-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, or any damage as shown in Section A-A, contact AIRBUS
within 3 months of this inspection.
(5) Subtask 570256-832-402-003 - Do a Detailed Inspection of the Top Skin between
Ribs 1 and 29 and the Bottom Wing Skin between Ribs 15 and 29 on the LH Wing
Work Zones and Access Panels
Zone
 Access/Work location
500
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-33-11
Fig. A-UBCAB
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Fig. A-UFAAA
Flowchart
Sheet 01
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 40
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A300
SERVICE BULLETIN
(a) On the top and bottom wing skin, do a detailed inspection for damage that is more
than what is specified in the current revision of the SRM.
1
 Refer to Fig. A-UBCAB Sheet 01
 and Fig. A-UBCAB Sheet 03
 ,V i e wD .
On the bottom wing skin between ribs 15 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
2
 Refer to Fig. A-UBCAB Sheet 01
 and Fig. A-UBCAB Sheet 02
 ,V i e wC .
On the top wing skin between ribs 1 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
(6) Subtask 570256-832-406-002 - Do a Detailed Inspection of the Top Skin between
Ribs 1 and 29 and the Bottom Wing Skin between Ribs 15 and 29 on the RH Wing
Work Zones and Access Panels
Zone
 Access/Work location
600
 Work location
 from Rib 1 to Rib 29
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 41
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A300
SERVICE BULLETIN
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
References
Structural Repair Manual (SRM)
 57-33-11
Fig. A-UBCAB
Detailed Inspection of the Top and
Bottom Skin
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Fig. A-UFAAA
Flowchart
Sheet 01
(a) On the top and bottom wing skin, do a detailed inspection for damage that is more
than what is specified in the current revision of the SRM.
1
 Refer to Fig. A-UBCAB Sheet 01
 and Fig. A-UBCAB Sheet 03
 ,V i e wD .
On the bottom wing skin between ribs 15 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
Refer to Fig. A-UFAAA Sheet 01
 .
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
2
 Refer to Fig. A-UBCAB Sheet 01
 and Fig. A-UBCAB Sheet 02
 ,V i e wC .
On the top wing skin between ribs 1 thru 29, do a detailed inspection in
accordance with SRM 57-33-11.
- If there is no damage, and no repairs that are outside the limits set in the
SRM, no further action is required at this rib
- If there is a repair that is outside of the limits set in the SRM that can be
replaced, replace the repair in accordance with an applicable SRM repair,
or another approved repair within 3 months of this repair survey (Refer to
Repair Evaluation Guidelines)
- Record the damage or repair if it is not already recorded
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 42
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A300
SERVICE BULLETIN
- If there is a repair that is outside of the limits set in the SRM that cannot
be replaced, contact AIRBUS within 3 months of this inspection.
**CONF ALL
D. TEST
**CONF 001
None
**CONF 002
None
**CONF ALL
E. CLOSE-UP
**CONF 001
(1) Subtask 570256-942-404-001 - CLOSE-UP
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 542EB, Panel 543AB, Panel 543BB, Panel
543CB, Panel 543DB, Panel 541AB, Panel
541BB, Panel 542DB, Panel 542CB, Panel
581DB, Panel 581EB, Panel 581FB, Panel
581GB, Panel 523EB, Panel 523FB, Panel
523HB, Panel 523JB, Panel 523CB, Panel
523DB, Panel 581CB
Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
640
 Access
 Panel 643AB, Panel 643BB, Panel 643CB,
Panel 643DB, Panel 641AB, Panel 641BB,
Panel 642CB, Panel 642DB, Panel 642EB,
Panel 681CB, Panel 681DB, Panel 681EB,
Panel 681FB, Panel 681GB, Panel 623EB,
Panel 623FB, Panel 623HB, Panel 623JB, Panel
623CB, Panel 623DB
Work location
 Rib 4 FWD
Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
550
 Access
 Panel 550LB, Panel 550KB
Work location
 Rib 22
650
 Access
 Panel 650LB, Panel 650KB
Work location
 Rib 22
500
 Work location
 from Rib 1 to Rib 29
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 43
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A300
SERVICE BULLETIN
600
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install (as necessary) the panels that follow to close access to rib 4 FWD, refer to
AMM 28-11-14, Page Block 401:
- 541AB, 641AB, 541BB and 641BB.
(c) Install (as necessary) the panels that follow to close access to rib 5 AFT and rib 7
AFT, refer to AMM 28-11-14, Page Block 401:
- 542CB, 642CB, 542DB and 642DB.
(d) Install (as necessary) the panels that follow to close access to rib 22, refer to AMM
28-11-14, Page Block 401:
- 550LB, 650LB, 550KB and 650KB.
(e) Install (as necessary) the panels that follow to close access to the front spar at rib
9 to 13, refer to AMM 28-11-14, Page Block 401:
1
 FWD of the front spar, install:
- 523CB, 623CB, 523DB, 623DB, 523EB, 623EB, 523FB, 623FB, 523HB,
623HB, 523JB and 623JB.
2
 AFT of the front spar, install:
- 542EB, 642EB, 543AB, 643AB, 543BB, 643BB, 543CB, 643CB, 543DB
and 643DB.
(f) Install (as necessary) the panels that follow to close access to the rear spar at rib 9
to 13, refer to AMM 28-11-14, Page Block 401:
1
 AFT of the rear spar, install:
- 581CB, 681CB, 581DB, 681DB, 581EB, 681EB, 581FB, 681FB, 581GB
and 681GB.
(g) Do the close up procedures as specified in the ’Removal/Installation of the Manhole
Covers’, refer to AMM 28-11-14, Page Block 401.
(h) Remove the WARNING NOTICE from the cockpit.
(i) Remove the safety barriers.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 44
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 55

@A300
SERVICE BULLETIN
(j) Put the aircraft back to its initial configuration.
**CONF 002
(1) Subtask 570256-942-404-002 - CLOSE-UP
Work Zones and Access Panels
Zone
 Access/Work location
540
 Access
 Panel 542CB, Panel 542DB, Panel 542EB,
Panel 543AB, Panel 543BB, Panel 543CB,
Panel 543DB, Panel 523CB, Panel 523DB,
Panel 523EB, Panel 523FB, Panel 523HB, Panel
523JB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
640
 Access
 Panel 642CB, Panel 642DB, Panel 642EB,
Panel 643AB, Panel 643BB, Panel 643CB,
Panel 643DB, Panel 623CB, Panel 623DB,
Panel 623EB, Panel 623FB, Panel 623HB, Panel
623JB
Work location
 Rib 5 AFT
Rib 7 AFT
from Rib 9 to Rib 10
500
 Work location
 from Rib 1 to Rib 29
600
 Work location
 from Rib 1 to Rib 29
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 28-11-14, Page Block 401
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install (as necessary) the panels that follow to close access to rib 5 AFT:
- 542CB and 642CB.
(c) Install (as necessary) the panels that follow to close access to rib 7 AFT, refer to
AMM 28-11-14, Page Block 401:
- 542DB and 642DB.
(d) Install (as necessary) the panels that follow to close to the front spar at rib 9 to 10,
refer to AMM 28-11-14, Page Block 401:
1
 FWD of the front spar, install:
- 523CB, 623CB, 523DB, 623DB, 523EB, 623EB, 523FB, 623FB, 523HB,
623HB, 523JB and 623JB.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 45
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 56

@A300
SERVICE BULLETIN
2
 AFT of the front spar, install:
- 542EB, 642EB, 543AB, 643AB, 543BB, 643BB, 543CB, 643CB, 543DB
and 643DB.
(e) Do the close up procedures as specified in the ’Removal/Installation of the Manhole
Covers’, refer to AMM 28-11-14, Page Block 401.
(f) Remove the WARNING NOTICE from the cockpit.
(g) Remove the safety barriers.
(h) Put the aircraft back to its initial configuration.
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 46
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 57

@A300
SERVICE BULLETIN
**CONF ALL
REPAIR PERFORMED ACCORDING TO AN
SRM REPAIR PRINCIPLE
CHECK THE REPAIR AS PUBLISHED
IN THE CURRENT SRM REVISION
REPAIR CATEGORY
PUBLISHED FOR THAT REPAIR
IN THE CURRENT SRM
REVISION?
WAS THE SRM REPAIR
DELETED, SET TO ’NO
FURTHER APPLICATION’
OR SUPERSEDED?
RECORD RELEVANT REPAIR
CATEGORY, FOLLOW REPAIR
LIMITATIONS AND/OR INSPECTION
REQUIREMENTS, IF ANY
WITHIN 3 MONTHS AFTER THE REPAIR SURVEY:
REPLACE REPAIR WITH AN APPROPRAITE CURRENT
SRM REPAIR          OR ANOTHER APPROVED REPAIR
OR
01
COMPLETE THE RELEVANT PRE DEFINED REPORTING
SHEET (PDRS) OR EQUIVALENT, AND CONTACT AIRBUS
YES
COMPLIANCE TIMES GIVEN IN THIS SERVICE BULLETIN.
THE PURPOSE OF FLOW CHARTS IS TO SUPPLEMENT THE INFORMATION GIVEN IN THE PROCEDURE AND COMPLIANCE PARAGRAPHS AND NOT TO SERVE AS THE PRIMARY SOURCE FOR TASKS OR
SEE ALSO NOTE GIVEN IN SECTION 2.5 STEP 1 OF THE A300 REPAIR EVALUATION GUIDELINES REGARDING ASSISTANCE FROM AIRBUS FOR THE DESIGN TOLERANCE EVALUATION03
THIS INCLUDES DELETED REPAIRS, REPAIRS SET TO ’NO FURTHER APPLICATION’ OR SUPERSEDED REPAIRS02
NOTE:
DO NOT INSTALL AN SRM REPAIR PUBLISHED WITHOUT CATEGORY ON AN AIRCRAFT ON WHICH THE REPAIR SURVEY IS ONGOING OR HAS BEEN COMPLETED01
WITHIN 3 MONTHS AFTER THE REPAIR SURVEY,
CONTACT AIRBUS FOR REPAIR CATEGORY 
AND DT DATA                       01 03
NO
YES NO
NO YES
EXISTING REPAIR IN
ACCORDANCE WITH THE
CURRENT SRM REVISION?
02
IS THE
05
05
04
05
CURRENT SRM AT TIME OF SB PUBLICATION, INCLUDING TEMPORARY REVISIONS05
REFER TO REPAIR EVALUATION GUIDELINES04
IS A
04
A_SB_570256_7_FAAA_01_02
Figure A-UFAAA - Sheet 01
Flowchart
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 47
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 58

@A300
SERVICE BULLETIN
**CONF 001
A_SB_570256_7_BAAA_01_00
A
A
LH SHOWN
RH SIMILAR
A
B
C
D
E
RIB4RIB5
RIB7
FRONT SPAR REAR SPAR
CENTER SPAR
RIB22
Z500
Z600
Figure A-U BAAA - S heet 01
Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT and 22
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 48
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 59

@A300
SERVICE BULLETIN
**CONF 001
A_SB_570256_7_BAAA_02_00
FOR AREAS 1, 2 AND 3 NO SCORES, SCRATCHES, ABRASIONS
OR CORROSION PERMITTED. NO NICKS ARE PERMITTED ON
THE FREE EDGES OF FLANGES BORDERING THESE EDGES.
FOR AREA 1 NO SCORES, SCRATCHES, ABRASIONS OR
CORROSION PERMITTED. NO NICKS ARE PERMITTED ON
THE FREE EDGES OF FLANGES BORDERING THE EDGE.
B
FRONT
SPAR
CENTER
SPAR
RIB4F
STGR11
STGR5
1
2
3
STGR13
STGR20
REAR
SPAR
CENTER
SPAR
1
RIB5A
C
FWD
FWD
Figure A-U BAAA - S heet 02
Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT and 22
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 49
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 60

@A300
SERVICE BULLETIN
**CONF 001
CENTER
SPAR
FOR AREA 1 NO SCORES, SCRATCHES, ABRASIONS OR
CORROSION PERMITTED. NO NICKS ARE PERMITTED ON
THE FREE EDGES OF FLANGES BORDERING THIS AREA.
REAR
SPAR
REAR
SPAR
FRONT
SPAR
RIB7A
RIB22
FOR AREA 1 NO SCORES, SCRATCHES, ABRASIONS OR
CORROSION PERMITTED ON THE STIFFENER. NO NICKS
ARE PERMITTED ON THE FREE EDGE OF THE STIFFENER.
1 STGR13
STGR20
STGR12
STGR18
1
D
E
FWD
FWD
A_SB_570256_7_BAAA_03_01
Figure A-U BAAA - S heet 03
Detailed Inspection of Ribs 4 FWD, 5 AFT, 7 AFT and 22
DATE: Aug 03/15 SERVICE BULLETIN No.: A300-57-0256
REVISION No.: 00 - Aug 03/15 Page: 50
7
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

The text continues at https://openairdocs.org/service-documents/airbus/a300-57-0256/file/b1ba676f00a4.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
