# Airbus Service Bulletin A300-57-6120

Copy: No revision named ("FAA-2016-9055_SB A300-57-6120"), 108 pages: PDF https://openairdocs.org/files/sha256/37/2f/372f492dca573f12062adbf3c8c6e0a2276ab8e09b3143b9dbd311f645550114; text https://openairdocs.org/service-documents/airbus/a300-57-6120/file/372f492dca57.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2016-9055; AD 2017-15-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A300-57-6120
- Page: https://openairdocs.org/service-documents/airbus/a300-57-6120

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-17-10](https://openairdocs.org/ad/2018-17-10.md), effective Sep 24, 2018: No revision named
- [AD 2017-15-17](https://openairdocs.org/ad/2017-15-17.md), effective Sep 5, 2017: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a300-57-6120/proposed.md), [3 difficulty reports](https://openairdocs.org/service-documents/airbus/a300-57-6120/reports.md).

## Text (108 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2016-9055; AD 2017-15-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A300-600
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - CENTER WINGS - INSPECTION OF FR40 LOWER OUTBOARD
RADIUS AREA
**CONF ALL
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
A full stress analysis of the Frame 40 lower area, supported by a detailed Finite Element Model, of
the configuration post MOD No. 10221S20394 was recently completed. The results showed a high
probability to detect a crack in the lower radius of the Frame 40 forward fitting for aircraft accumulating
more than 19000FC / 41000FH. This result led AIRBUS to launch an inspection per AOT reference
A57W009-16. Three findings were reported during AOT inspection and repaired with a cut-out.
This Service Bulletin establishes an inspection program by High Frequency Eddy Current (HFEC)
(Option 1) or by High Frequency Eddy Current (HFEC) and Rototest (Option 2) that supersedes AOT
A57W009-16 for all aircraft post MOD No. 10221S20394. A repair by cutout or stop drilling may be
required depending on the inspection results as instructed in this Service Bulletin.
The procedure as described in this Service Bulletin is to be performed if no Airbus repair and/or repair
improvement has been previously performed in the same area. In case of repairs performed previously,
please contact AIRBUS Repair Support department for further instructions.
Accomplishment of this Service Bulletin will detect crack formation in the lower radius of the Frame 40
forward fitting and offer a repair solution if cracks are detected avoiding more costly repairs and
downtime in the future.
The Operational/Maintenance Consequences of this Service Bulletin are covered by the update of the
affected publications detailed in ’PLANNING INFORMATION’.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 MANDATORY (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 YES
 A/C OPERATION AFFECTED
 NO
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 1
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A300-600
SERVICE BULLETIN
SUMMARY
EVALUATION TABLE
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 ETOPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
DE-FUELLING/VENTILATION
 YES
NOTE
 (1)
: Service Bulletin must be accomplished.
MATERIAL PRICE INFORMATION
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 576120C01R01
 2
 4,700.00
 Fasteners, Cover Plate, Filler
Kit 576120C02R01
 2
 3,600.00
 Fasteners, Stop Bracket, Plug
TOTAL
 8,300.00
Component COMPC01
 2
 See SB
 Bolt, Nut
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
14S AAW AHK BCS FDX IRA IRM MNB MRJ QSM SUD THA UPS
URS UTP
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
 57.10.00.014
OEB
 None
AOT
 A57W009-16
SIL
 None
ISI
 00.00.00198
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 2
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A300-600
SERVICE BULLETIN
SUMMARY
MANPOWER
Task 576120-832-942-001: HFEC Inspection of the Frame 40 Forward Fitting (Option 1)
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 3.50
Task 576120-832-943-001: HFEC Inspection of the Frame 40 Forward Fitting and Rototest
Inspection of the Fastener Hole (Option 2)
TOTAL MANHOURS
 30.50
ELAPSED TIME (HOURS)
 15.25
Task 576120-833-942-001: Repair The Frame 40 Forward Fitting by Cutout
TOTAL MANHOURS
 43.50
ELAPSED TIME (HOURS)
 21.75
Task 576120-833-943-001: Repair the Frame 40 Forward Fitting by Stop Drilling
TOTAL MANHOURS
 57.50
ELAPSED TIME (HOURS)
 28.75
Task 576120-832-944-001: HFEC Inspection of the Frame 40 Forward Fitting After Repair by
Cutout
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 3.50
Task 576120-832-945-001: Inspection of the Frame 40 Forward Fitting After Repair by Stop
Drilling
TOTAL MANHOURS
 28.50
ELAPSED TIME (HOURS)
 14.25
APPENDICES
Appendix 01 - Gantt Chart (Inspection Option 1)
Appendix 02 - Gantt Chart (Inspection Option 2)
Appendix 03 - Gantt Chart (Repair by Cutout)
Appendix 04 - Gantt Chart (Repair by Stop Drilling)
Appendix 05 - Gantt Chart (Inspection After Cutout)
Appendix 06 - Gantt Chart (Inspection After Stop Drilling)
Appendix 07 - Inspection Report
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 3
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A300-600
SERVICE BULLETIN
SUMMARY
**CONF ALL
B
B
B
RH SHOWN
LH SYMMETRICAL
FRONT SPAR DATUM
RIB1 DATUM
FR40
FR47
A
FR40
C
Z140
A
D_SB_576120_0_SAAA_01_00
Figure A-SSAAA - Sheet 01
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 4
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A300-600
SERVICE BULLETIN
SUMMARY
**CONF ALL
C
VIEW LOOKING AFT
RH SHOWN
LH SYMMETRICAL
STGR33
STGR32
NOTE:
AREA AAREA B
TYPICAL CRACKS
AREA TO BE INSPECTED
INBD
D_SB_576120_0_SAAA_02_02
Figure A-SSAAA - Sheet 02
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 5
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A300-600
SERVICE BULLETIN
SUMMARY
This Page Intentionally Left Blank
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 6
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A300-600
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 57
TITLE: WINGS - CENTER WINGS - INSPECTION OF FR40 LOWER OUTBOARD
RADIUS AREA
MODIFICATION No.: None
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
NOTE
: This Service Bulletin is only applicable to aircraft on which MOD No.
10221S20394 is embodied.
(1) Models
B4-605R B4-622R C4-605R/F F4-605R F4-622R
(2) Effectivity by MSN
0726-0730 0732-0746 0748-0750 0752-0764 0766 0768-0775 0777-0794 0797
0799-0840 0845-0878
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
14S
 0787
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 1
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A300-600
SERVICE BULLETIN
OPERATOR
 MSN
AAW
 0788
AHK
 0770 0855 0856 0857 0858 0859 0860 0870 0871
BCS
 0729 0730 0737 0740 0743 0753 0783 0797 0836 0837 0872
FDX
 0726 0728 0735 0736 0738 0742 0745 0748 0752 0757 0759 0760
0761 0766 0768 0769 0771 0772 0774 0777 0778 0779 0780 0781
0789 0790 0791 0792 0793 0794 0799 0800 0801 0802 0803 0804
0873 0874 0875 0876 0877 0878
IRA
 0727
IRM
 0773 0838
MNB
 0734 0739 0755 0756 0758
MRJ
 0750 0762
QSM
 0744 0749 0764
SUD
 0775
THA
 0782 0784 0785 0786
UPS
 0805 0806 0807 0808 0809 0810 0811 0812 0813 0814 0815 0816
0817 0818 0819 0820 0821 0822 0823 0824 0825 0826 0827 0828
0829 0830 0831 0832 0833 0834 0835 0839 0840 0845 0846 0847
0848 0849 0850 0851 0852 0853 0854 0861 0862 0863 0864 0865
0866 0867 0868 0869
URS
 0733
UTP
 0732 0741 0746 0754 0763
(4) Configuration by MSN
MSN
 CONFIGURATION
0726 0727 0728 0729 0730 0732 0733 0734 0735 0736 0737
0738 0739 0740 0741 0742 0743 0744 0745 0746 0748 0749
0750 0752 0753 0754 0755 0756 0757 0758 0759 0760 0761
0762 0763 0764 0766 0768 0769 0770 0771 0772 0773 0774
0775 0777 0778 0779 0780 0781 0782 0783 0784 0785 0786
0787 0788 0789 0790 0791 0792 0793 0794 0797 0799 0800
0801 0802 0803 0804 0805 0806 0807 0808 0809 0810 0811
0812 0813 0814 0815 0816 0817 0818 0819 0820 0821 0822
0823 0824 0825 0826 0827 0828 0829 0830 0831 0832 0833
0834 0835 0836 0837 0838 0839 0840 0845 0846 0847 0848
0849 0850 0851 0852 0853 0854 0855 0856 0857 0858 0859
0860 0861 0862 0863 0864 0865 0866 0867 0868 0869 0870
0871 0872 0873 0874 0875 0876 0877 0878
001
(5) Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft on which MOD No. 10221S20394 is embodied.
(6) Material Effectivity
MATERIAL
 QTY PER A/C
 SEE NOTES
Consumable CMLC01
 1
Kit 576120C01R01
 2
Kit 576120C02R01
 2
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 2
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A300-600
SERVICE BULLETIN
MATERIAL
 QTY PER A/C
 SEE NOTES
Component COMPC01
 2
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
A full stress analysis of the Frame 40 lower area, supported by a detailed Finite Element
Model, of the configuration post MOD No. 10221S20394 was recently completed. The
results showed a high probability to detect a crack in the lower radius of the Frame 40
forward fitting for aircraft accumulating more than 19000FC / 41000FH. This result led
AIRBUS to launch an inspection per AOT reference A57W009-16. Three findings were
reported during AOT inspection and repaired with a cut-out.
(2) Objective/Action
This Service Bulletin establishes an inspection program by High Frequency Eddy Current
(HFEC) (Option 1) or by High Frequency Eddy Current (HFEC) and Rototest (Option
2) that supersedes AOT A57W009-16 for all aircraft post MOD No. 10221S20394. A
repair by cutout or stop drilling may be required depending on the inspection results as
instructed in this Service Bulletin.
The procedure as described in this Service Bulletin is to be performed if no Airbus repair
and/or repair improvement has been previously performed in the same area. In case of
repairs performed previously, please contact AIRBUS Repair Support department for
further instructions.
(3) Advantages
Accomplishment of this Service Bulletin will detect crack formation in the lower radius of
the Frame 40 forward fitting and offer a repair solution if cracks are detected avoiding
more costly repairs and downtime in the future.
(4) Operational/Maintenance Consequences
The Operational/Maintenance Consequences of this Service Bulletin are covered by the
update of the affected publications detailed in ’PLANNING INFORMATION’.
D. DESCRIPTION
NOTE
: To accomplish this Service Bulletin, you have 02 inspection options and 02
repair options depending on the inspection result.
To accomplish this Service Bulletin it is necessary to :
Task 576120-832-942-001: HFEC Inspection of the Frame 40 Forward Fitting (Option 1)
(1) Do a HFEC Inspection of the LH Frame 40 Forward Fitting
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 3
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A300-600
SERVICE BULLETIN
(2) Do a HFEC Inspection of the RH Frame 40 Forward Fitting
Task 576120-832-943-001: HFEC Inspection of the Frame 40 Forward Fitting and Rototest
Inspection of the Fastener Hole (Option 2)
(1) Do a HFEC Inspection of the LH Frame 40 Forward Fitting and Rototest of the
Fastener Hole
(2) Do a HFEC Inspection of the RH Frame 40 Forward Fitting and Rototest of the
Fastener Hole
Task 576120-833-942-001: Repair The Frame 40 Forward Fitting by Cutout
(1) Repair the Crack on the LH Frame 40 Forward Fitting by Cutout
(2) Repair the Crack on the RH Frame 40 Forward Fitting by Cutout
Task 576120-833-943-001: Repair the Frame 40 Forward Fitting by Stop Drilling
(1) Repair the Crack on the LH Frame 40 Forward Fitting by Stop Drilling
(2) Repair the Crack on the RH Frame 40 Forward Fitting by Stop Drilling
Task 576120-832-944-001: HFEC Inspection of the Frame 40 Forward Fitting After Repair by
Cutout
(1) Do a HFEC Inspection of the LH Frame 40 Forward Fitting After Repair by Cutout
(2) Do a HFEC Inspection of the RH Frame 40 Forward Fitting After Repair by Cutout
Task 576120-832-945-001: Inspection of the Frame 40 Forward Fitting After Repair by Stop
Drilling
(1) Do a HFEC Inspection of the LH Frame 40 Forward Fitting After Repair by Stop
Drilling
(2) Do a HFEC Inspection of the RH Frame 40 Forward Fitting After Repair by Stop
Drilling
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an Airworthiness
Directive (AD) published by the European Av iation Safety Agenc y (EASA) will be issued
to confirm this classification. It is anticipated that the AD will confirm the thresholds
and/or intervals and/or date given but reference should be made to the AD for
confirmation of the mandated accomplishment timescale.
All inspection reports must be sent to Airbus within one month after the inspection date.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 4
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A300-600
SERVICE BULLETIN
Table 1 - Inspection of the Frame 40 Forward Fitting
Compliance time (whichever occurs later)
Condition
 Action
Threshold
(whichever occurs
first from first flight)
Grace Period
Repetitive Interval
(whichever occurs
first from last
inspection)
Do a HFEC
Inspection in
accordance with
TASK
576120-832-942
001 HFEC
Inspection of the
Frame 40
Forward Fitting
(Option 1)
- AFT higher than
1.5: 14700 FC /
31900 FH
-A F T l o w e r o r
equal to 1.5:
15900 FC /
23900 FH
See NOTE (**)
See NOTE (*)
 none
OR
All aircraft
Do a HFEC and
Rototest
Inspection in
accordance with
TASK
576120-832-943
001 HFEC
Inspection of the
Frame 40
Forward Fitting
and Rototest
Inspection of the
Fastener Hole
(Option 2)
- AFT higher than
1.5: 14700 FC /
31900 FH
-A F T l o w e r o r
equal to 1.5:
15900 FC /
23900 FH
See NOTE (**)
See NOTE (*)
 none
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 5
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A300-600
SERVICE BULLETIN
Repeat the HFEC
Inspection in
accordance with
TASK
576120-832-942
001 HFEC
Inspection of the
Frame 40
Forward Fitting
(Option 1)
none
 none
 - AFT higher than
1.5: 1900 FC /
4300 FH
-A F T l o w e r o r
equal to 1.5:
2100 FC / 3200
FH
See NOTE (***)
OR
If no crack
is found
Repeat the HFEC
and Rototest
Inspection of the
Fastener Hole in
accordance with
TASK
576120-832-943
001 HFEC
Inspection of the
Frame 40
Forward Fitting
and Rototest
Inspection of the
Fastener Hole
(Option 2)
none
 none
 - AFT higher than
1.5: 6600 FC /
14300 FH
-A F T l o w e r o r
equal to 1.5:
7100 FC / 10700
FH
See NOTE (***)
Repair in
accordance with
TASK
576120-833-942
001 Repair The
Frame 40
Forward Fitting by
Cutout
Before next flight
 none
 none
If a crack
tip is found
in area A
Do a HFEC
Inspection in
accordance with
TASK
576120-832-944
001 HFEC
Inspection of the
Frame 40
Forward Fitting
After Repair by
Cutout
Refer to table 2
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 6
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A300-600
SERVICE BULLETIN
Repair in
accordance with
TASK
576120-833-943
001 Repair the
Frame 40
Forward Fitting by
Stop Drilling
Before next flight
 none
 none
If a crack
tip is found
in area B
Do a HFEC
Inspection in
accordance with
TASK
576120-832-945
001 Inspection of
the Frame 40
Forward Fitting
After Repair by
Stop Drilling
Refer to table 3
If a crack
tip is found
beyond
area B
Contact AIRBUS
 Before next flight
 none
 none
NOTE (*):
- For aircraft inspected as per AOT A57W009-16 REV 01 before the issuance date of
this Service Bulletin, as applicable:
. GP = 1900 FC / 4300 FH (whichever occurs first) since last AOT inspection for
AFT higher than 1.5.
. GP = 2100 FC / 3200 FH (whichever occurs first) since last AOT inspection for
AFT lower or equal to 1.5.
- For aircraft not inspected per AOT A57W009-16 REV 01 before the issuance date
of this Service Bulletin:
. GP = 12 Months from issuance date of this Service Bulletin without exceeding
the compliance time given in the AOT.
NOTE (**): Average Flight Time = FH/FC since aircraft Entry Into Service.
NOTE (***): Average Flight Time = FH/FC since last inspection.
Table 2 - Inspection of the Frame 40 Forward Fitting After Repair by Cutout
Compliance time (whichever occurs later)
Condition
 Action
Threshold (whichever
occurs first from repair)
Grace
Period
Repetitive interval
(whichever occurs first from
last inspection)
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 7
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A300-600
SERVICE BULLETIN
All aircraft
 Do a HFEC
Inspection in
accordance
with TASK
576120-832-944
001 HFEC
Inspection of
the Frame 40
Forward Fitting
After Repair by
Cutout
- AFT higher than 1.5:
4500 FC / 9800 FH
- AFT lower or equal to
1.5: 4900 FC / 7300 FH
See NOTE (*)
none
 none
If no crack is
found
Repeat the
HFEC
Inspection in
accordance
with TASK
576120-832-944
001 HFEC
Inspection of
the Frame 40
Forward Fitting
After Repair by
Cutout
none
 none
 - AFT higher than 1.5:
4500 FC / 9800 FH
- AFT lower or equal to
1.5: 4900 FC / 7300 FH
See NOTE (**)
If a crack is
found
Contact
AIRBUS
Before next flight
 none
 none
NOTE (*): Average Flight Time = FH/FC since repair embodiment.
NOTE (**): Average Flight Time = FH/FC since last inspection.
Table 3 - Inspection of the Frame 40 Forward Fitting After Repair by Stop Drilling
Compliance time (whichever occurs later)
Condition
 Action
Threshold (whichever
occurs first from
repair)
Grace Period
Repetitive interval
(whichever occurs first
from last inspection)
All
aircraft
Do a HFEC Inspection
in accordance with
TASK 576120-832-945
001 Inspection of the
Frame 40 Forward
Fitting After Repair by
Stop Drilling
- AFT higher than
1.5: 1500 FC / 3400
FH
- AFT lower or equal
to 1.5: 1700 FC /
2500 FH
See NOTE (*)
none
 none
If no
crack is
found
Repeat the HFEC
Inspection in
accordance with TASK
576120-832-945 001
Inspection of the Frame
40 Forward Fitting After
Repair by Stop Drilling
none
 none
 - AFT higher than 1.5:
1500 FC / 3400 FH
- AFT lower or equal to
1.5: 1700 FC / 2500
FH
See NOTE (**)
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 8
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A300-600
SERVICE BULLETIN
If a
crack is
found
Contact AIRBUS
 Before next flight
 none
 none
NOTE (*): Average Flight Time = FH/FC since repair embodiment.
NOTE (**): Average Flight Time = FH/FC since last inspection.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
Task 576120-832-942-001: HFEC Inspection of the Frame 40 Forward Fitting (Option 1)
Get Access
 2.00
On Aircraft
Do a HFEC Inspection of the LH Frame 40 Forward
Fitting
0.50
Do a HFEC Inspection of the RH Frame 40 Forward
Fitting
0.50
Tests
 2.00
Close-Up
 2.00
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 3.50
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SAAAA
 given in Appendix 01.
Task 576120-832-943-001: HFEC Inspection of the Frame 40 Forward Fitting and Rototest
Inspection of the Fastener Hole (Option 2)
Get Access
 13.00
On Aircraft
Do a HFEC Inspection of the LH Frame 40 Forward
Fitting and Rototest of the Fastener Hole
1.50
Do a HFEC Inspection of the RH Frame 40 Forward
Fitting and Rototest of the Fastener Hole
1.50
Tests
 4.50
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 9
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A300-600
SERVICE BULLETIN
Task 576120-832-943-001: HFEC Inspection of the Frame 40 Forward Fitting and Rototest
Inspection of the Fastener Hole (Option 2)
Close-Up
 10.00
TOTAL MANHOURS
 30.50
ELAPSED TIME (HOURS)
 15.25
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SABAA
 given in Appendix 02.
Task 576120-833-942-001: Repair The Frame 40 Forward Fitting by Cutout
Get Access
 13.00
On Aircraft
Repair the Crack on the LH Frame 40 Forward Fitting
by Cutout
8.00
Repair the Crack on the RH Frame 40 Forward Fitting
by Cutout
8.00
Tests
 4.50
Close-Up
 10.00
TOTAL MANHOURS
 43.50
ELAPSED TIME (HOURS)
 21.75
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SACAA
 given in Appendix 03.
Task 576120-833-943-001: Repair the Frame 40 Forward Fitting by Stop Drilling
Get Access
 13.00
On Aircraft
Repair the Crack on the LH Frame 40 Forward Fitting
by Stop Drilling
15.00
Repair the Crack on the RH Frame 40 Forward Fitting
by Stop Drilling
15.00
Tests
 4.50
Close-Up
 10.00
TOTAL MANHOURS
 57.50
ELAPSED TIME (HOURS)
 28.75
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SADAA
 given in Appendix 04.
Task 576120-832-944-001: HFEC Inspection of the Frame 40 Forward Fitting After Repair by
Cutout
Get Access
 2.00
On Aircraft
Do a HFEC Inspection of the LH Frame 40 Forward
Fitting After Repair by Cutout
0.50
Do a HFEC Inspection of the RH Frame 40 Forward
Fitting After Repair by Cutout
0.50
Tests
 2.00
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 10
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A300-600
SERVICE BULLETIN
Task 576120-832-944-001: HFEC Inspection of the Frame 40 Forward Fitting After Repair by
Cutout
Close-Up
 2.00
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 3.50
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SAEAA
 given in Appendix 05.
Task 576120-832-945-001: Inspection of the Frame 40 Forward Fitting After Repair by Stop
Drilling
Get Access
 13.00
On Aircraft
Do a HFEC Inspection of the LH Frame 40 Forward
Fitting After Repair by Stop Drilling
0.50
Do a HFEC Inspection of the RH Frame 40 Forward
Fitting After Repair by Stop Drilling
0.50
Tests
 4.50
Close-Up
 10.00
TOTAL MANHOURS
 28.50
ELAPSED TIME (HOURS)
 14.25
NOTE
: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-SAFAA
 given in Appendix 06.
H. WEIGHT AND BALANCE
Not Changed
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
Aircraft Maintenance Manual (AMM)
 06-21-00 06-31-53 06-41-00
20-21-12 24-00-00 25-72-41
28-00-00 28-10-00 28-11-29
28-13-21 28-18-00 28-25-00
36-11-00
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-55-00
Non Destructive Test Manual (NTM)
 51-10-01 51-10-02 51-10-04
51-10-08 51-10-16 51-10-18
51-70-00
Repair Instruction
 R53810798
R53810799
Standards Manual (SM)
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 11
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A300-600
SERVICE BULLETIN
Structural Repair Manual (SRM)
 51-21-00 51-22-00 51-23-10
51-24-00 51-27-00 51-40-00
51-40-20 51-40-30 51-40-40
51-40-46 51-40-50 51-40-51
51-49-00 51-70-00 51-70-20
51-71-80 51-73-10 51-75-10
K. PUBLICATION AFFECTED
Impact on scheduled maintenance: refer to MPD.
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 12
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A300-600
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Kit 576120C01R01
Kit 576120C02R01
AIRBUS Material, Logistics and Suppliers
ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by E-mail: airbus.kit@airbus.com
Telephone Hotline:
A300/310: +49 40 743 51616
For standard hardware the purchase order shall be addressed to AIRBUS. Quote the
number of this Service Bulletin, the MSN and, if applicable the RIL reference. Please
send your request to:
Component COMPC01
 AIRBUS Material, Logistic and Suppliers
Standard Parts
For ordering by internet:
http://spares.airbus.com or vi a SPEC2000
For ordering by E-mail:
standard.parts@airbus.com
Phone: +49 (0) 40 50 76 40 03
(2) Price and Availability
Kit 576120C01R01
Cost
 2,350.00 USD
Availability
 190 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
Kit 576120C02R01
Cost
 1,800.00 USD
Availability
 240 calendar days from receipt of order
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 13
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A300-600
SERVICE BULLETIN
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
B. INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
E-mail: monitored.retrofit@airbus.com
C. LIST OF COMPONENTS
Kit 576120C01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
NAS1726-5E
 1
 NUT
NAS1726-8E
 1
 NUT
NSA5351-5-24
 1
 PIN
NSA5351-8-24
 1
 PIN
R5381079820000
 1
 FILLER
R5381079820100
 1
 COVER
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
Kit 576120C02R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
3
 EN6115V4-11
 1
 BOLT
4
 ASNA2529-4
 2
 NUT
5
 EN6115V4-12
 1
 BOLT
EN6115V4-3
 1
 BOLT
 (1)
EN6115V4X3
 1
 BOLT
EN6115V4Y3
 1
 BOLT
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 14
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A300-600
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
EN6115V5-3
 1
 BOLT
EN6115V5X3
 1
 BOLT
EN6115V5Y3
 1
 BOLT
R5381079920100
 1
 BRACKET
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
NOTE
 (1)
: The Bolts above that do not have an item number assigned, are used as a
plug. The Bolt is to be defined after drilling of the crack stop hole.
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
Non Aqueous Cleaner-General
 08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
Individual Compound - Nitrogen
Liquid
14VGC2
 As required
(2) Components
Component COMPC01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
1
 ASNA2027T8-19
 1
 BOLT
2
 ASNA2531-8
 1
 NUT
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: The components (items 1 and 2) are only necessary in case of
inspection by rototest. The quantity of these items are to be ordered as
required.
(3) Equipment
None
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 15
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A300-600
SERVICE BULLETIN
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
F. TOOLING
None
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 16
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A300-600
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 576120-832-942-001 - HFEC Inspection of the Frame 40 Forward Fitting (Option 1)
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 17
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A300-600
SERVICE BULLETIN
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.
Task Associated Data
Zone
140
Access
Door
 513AB 613AB
Manpower
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 3.50
A. GENERAL
(1) Subtask 576120-910-601-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-31-53, Page Block 001
06-41-00, Page Block 001
(a) If you find process and material specifications that you do not know in the design
drawings, refer to the cross-reference list in the Process and Material Specification
(PMS).
(b) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(c) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(d) For the identification of access panels, refer to AMM 06-41-00, Page Block 001.
(2) Subtask 576120-839-601-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B. PREPARATION
(1) Subtask 576120-941-601-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 18
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A300-600
SERVICE BULLETIN
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
36-11-00, Page Block 401
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(b) Put an access platform in position at zone 140.
(c) Open access doors 513AB and 613AB.
(d) If necessary, remove the left and right engine bleed air duct at Frame 40, refer to
AMM 36-11-00, Page Block 401.
C. PROCEDURE
(1) Subtask 576120-250-601-001 - Do a HFEC Inspection of the LH Frame 40 Forward
Fitting
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB
Work location
 Frame 40
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 19
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A300-600
SERVICE BULLETIN
Manpower Resources
Manhours
 0.50
Minimum number of person
 1
Subtask elapsed time
 0.50
Skills
 AIRFRAME
References
Non Destructive Test Manual (NTM)
 51-10-08
Fig. A-SBAAA
HFEC Inspection of Areas A and B and
of the Fastener Hole
Sheet 01
Sheet 02
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this inspection, refer to Fig. A-SFAAA
.
(a) Do a HFEC inspection in accordance with NTM 51-10-08 of the Frame 40 lower
radius in areas A and B as shown on Fig. A-SBAAA
.
1
 If no crack is found:
a
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
b
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If the crack tip is found in area A, do a cutout repair in accordance with TASK
576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
3
 If the crack tip is found in area B, do a stop drilling repair in accordance with
TASK 576120-833-943 001 Repair the Frame 40 Forward Fitting by Stop
Drilling .
4
 If the crack tip is found beyond area B:
a
 Contact Airbus before next flight.
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
(2) Subtask 576120-250-602-001 - Do a HFEC Inspection of the RH Frame 40 Forward
Fitting
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 613AB
Work location
 Frame 40
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 20
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A300-600
SERVICE BULLETIN
Manpower Resources
Manhours
 0.50
Minimum number of person
 1
Subtask elapsed time
 0.50
Skills
 AIRFRAME
References
Non Destructive Test Manual (NTM)
 51-10-08
Fig. A-SBAAA
HFEC Inspection of Areas A and B and
of the Fastener Hole
Sheet 01
Sheet 02
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this inspection, refer to Fig. A-SFAAA
.
(a) Do a HFEC inspection in accordance with NTM 51-10-08 of the Frame 40 lower
radius in areas A and B as shown on Fig. A-SBAAA
.
1
 If no crack is found:
a
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
b
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If the crack tip is found in area A, do a cutout repair in accordance with TASK
576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
3
 If the crack tip is found in area B, do a stop drilling repair in accordance with
TASK 576120-833-943 001 Repair the Frame 40 Forward Fitting by Stop
Drilling .
4
 If the crack tip is found beyond area B:
a
 Contact Airbus before next flight.
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
D. TEST
(1) Subtask 576120-790-601-001 - Leak Test
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 36-11-00, Page Block 401
NOTE
: This test requires the accomplishment of SUBTASK 576120-942-602 001
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 21
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A300-600
SERVICE BULLETIN
Close-up prior to performing this test.
(a) If previously installed in the Job Set-up, remove the safety clips and tags and close
the circuit breakers as specified after the installation of the engine air bleed supply
ducting between Frame 39 and Frame 40, refer to AMM 36-11-00, Page Block 401.
(b) If previously removed in the Job Set-up, do the leak test of the engine bleed air
system, refer to AMM 36-11-00, Page Block 401.
E. CLOSE-UP
(1) Subtask 576120-942-602-001 - Close-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 36-11-00, Page Block 401
(a) If you intend to accomplish an associated Repair Task during the same layover
period, the subsequent Close-up procedure is not necessary.
(b) If removed, reinstall the left and right engine bleed air duct at frame 40, refer to
AMM 36-11-00, Page Block 401.
(c) Close access doors 513AB and 613AB.
(d) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(e) Remove the access platform from under 140.
(f) Put the aircraft back to its initial configuration.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 22
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A300-600
SERVICE BULLETIN
Task 576120-832-943-001 - HFEC Inspection of the Frame 40 Forward Fitting and Rototest
Inspection of the Fastener Hole (Option 2)
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO WORK IN
OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE SAFETY PROCEDURES,
T H E R EI SAR I S KO F :
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
WARNING
: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION
(CDCCL). CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A
POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN
THE APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A
CDCCL ITEM CAN CAUSE A POSSIBLE FUEL TANK EXPLOSION.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 23
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A300-600
SERVICE BULLETIN
NOTE
: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
140
Access
Door
 513AB 613AB
Panel
 147AZ 147BZ 147CZ 147DZ 148AZ 148CZ 148DZ
Manpower
TOTAL MANHOURS
 30.50
ELAPSED TIME (HOURS)
 15.25
A. GENERAL
(1) Subtask 576120-910-602-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-31-53, Page Block 001
06-41-00, Page Block 001
20-21-12, Page Block 001
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-40-20
51-40-30
51-40-40
51-75-10
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 24
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A300-600
SERVICE BULLETIN
(a) If you find process and material specifications that you do not know in the design
drawings, refer to the cross-reference list in the Process and Material Specification
(PMS).
(b) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
the Consumable Materials List (CML).
(d) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(e) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(f) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(g) For the identification of access panels, refer to AMM 06-41-00, Page Block 001.
(h) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(i) Remove and install fasteners in accordance with SRM 51-40-20.
(j) Apply sealant in accordance with SRM 51-24-00.
(k) Renew the protective finish in accordance with SRM 51-75-10.
(l) Obtain fastener hole diameters and drill data in accordance with SRM 51-40-40.
(m) Obtain alternative and substitute fastener data in accordance with SRM 51-40-30.
(2) Subtask 576120-839-602-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 25
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A300-600
SERVICE BULLETIN
B. PREPARATION
(1) Subtask 576120-941-602-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Panel 147BZ, Panel 147CZ, Panel 147DZ, Panel
148CZ, Panel 148DZ, Panel 147AZ, Panel
148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
25-72-41, Page Block 401
28-00-00, Page Block 301
28-10-00, Page Block 301
28-11-29, Page Block 401
28-25-00, Page Block 301
36-11-00, Page Block 401
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(b) Put an access platform in position at zone 140.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 26
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A300-600
SERVICE BULLETIN
(c) Defuel the center fuel tank and the left and right inner wing fuel tank, refer to AMM
28-25-00, Page Block 301.
NOTE
: Defuel the center fuel tank and the left and right inner wing fuel tank
to avoid leakage during the rototest inspection.
(d) Degas and ventilate the fuel tanks, refer to AMM 28-00-00, Page Block 301 and
AMM 28-10-00, Page Block 301.
(e) Open the access doors 513AB and 613AB.
(f) Open the access panels 147CZ and 147DZ , refer to AMM 25-72-41, Page Block
401.
(g) Open the access panels 148CZ and 148DZ , refer to AMM 25-72-41, Page Block
401.
(h) Open the access panel 147BZ, refer to AMM 25-72-41, Page Block 401.
(i) Open the access panels 147AZ and 148AZ, refer to AMM 28-11-29, Page Block
401.
(j) If necessary, remove the left and right engine bleed air duct at Frame 40, refer to
AMM 36-11-00, Page Block 401.
C. PROCEDURE
(1) Subtask 576120-250-603-001 - Do a HFEC Inspection of the LH Frame 40 Forward
Fitting and Rototest of the Fastener Hole
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB
Panel 147AZ, Panel 147BZ, Panel 147CZ, Panel
147DZ
Work location
 Frame 40
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
Material necessary to do the job
Component COMPC01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 ASNA2027T8-19
 1
 BOLT
2
 ASNA2531-8
 1
 NUT
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 27
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A300-600
SERVICE BULLETIN
NOTE
: The components (items 1 and 2) are only necessary in case of
inspection by rototest. The quantity of these items are to be ordered as
required.
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
References
Consumable Material List (CML)
Non Destructive Test Manual (NTM)
 51-10-01
51-10-08
Structural Repair Manual (SRM)
 51-24-00
51-40-20
Fig. A-SBBAA
HFEC Inspection of Areas A and B and
Rototest Inspection of the Fastener Hole
Sheet 01
Sheet 02
Sheet 03
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this inspection, refer to Fig. A-SFAAA
.
(a) In accordance with SRM 51-40-20, remove as shown on Fig. A-SBBAA
:
1 Pin Item (1) Discard
1 Nut Item (2) Discard
(b) Do a HFEC inspection in accordance with NTM 51-10-08 of the Frame 40 lower
radius in areas A and B as shown on Fig. A-SBBAA
.
1
 If no crack is found:
a
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
b
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If the crack tip is found in area A, do a cutout repair in accordance with TASK
576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
3
 If the crack tip is found in area B, do a stop drilling repair in accordance with
TASK 576120-833-943 001 Repair the Frame 40 Forward Fitting by Stop
Drilling .
4
 If the crack tip is found beyond area B:
a
 Contact Airbus before next flight.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 28
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A300-600
SERVICE BULLETIN
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
(c) Do a Rototest inspection in accordance with NTM 51-10-01 of the fastener hole as
shown on Fig. A-SBBAA
1
 If no crack is found:
a
 In accordance with SRM 51-40-20 and SRM 51-24-00, wet install as
shown on Fig. A-SBBAA
:
1 Bolt ASNA2027T8-19 Item 1
1 Nut ASNA2531-8 Item 2
with:
Polysulfide Sealant-
General Purpose
Brushable
06AAA1 As required
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
c
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If a crack is found in the fastener hole, do a cutout repair in accordance with
TASK 576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
(2) Subtask 576120-250-604-001 - Do a HFEC Inspection of the RH Frame 40 Forward
Fitting and Rototest of the Fastener Hole
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 613AB
Panel 148AZ, Panel 148CZ, Panel 148DZ, Panel
147BZ
Work location
 Frame 40
Manpower Resources
Manhours
 1.50
Minimum number of person
 1
Subtask elapsed time
 1.50
Skills
 AIRFRAME
Material necessary to do the job
Component COMPC01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 ASNA2027T8-19
 1
 BOLT
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 29
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A300-600
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
2
 ASNA2531-8
 1
 NUT
NOTE
: The components (items 1 and 2) are only necessary in case of
inspection by rototest. The quantity of these items are to be ordered as
required.
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
References
Consumable Material List (CML)
Non Destructive Test Manual (NTM)
 51-10-01
51-10-08
Structural Repair Manual (SRM)
 51-24-00
51-40-20
Fig. A-SBBAA
HFEC Inspection of Areas A and B and
Rototest Inspection of the Fastener Hole
Sheet 01
Sheet 02
Sheet 03
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this inspection, refer to Fig. A-SFAAA
.
(a) In accordance with SRM 51-40-20, remove as shown on Fig. A-SBBAA
:
1 Pin Item (1) Discard
1 Nut Item (2) Discard
(b) Do a HFEC inspection in accordance with NTM 51-10-08 of the Frame 40 lower
radius in areas A and B as shown on Fig. A-SBBAA
.
1
 If no crack is found:
a
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
b
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If the crack tip is found in area A, do a cutout repair in accordance with TASK
576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
3
 If the crack tip is found in area B, do a stop drilling repair in accordance with
TASK 576120-833-943 001 Repair the Frame 40 Forward Fitting by Stop
Drilling .
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 30
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A300-600
SERVICE BULLETIN
4
 If the crack tip is found beyond area B:
a
 Contact Airbus before next flight.
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
(c) Do a Rototest inspection in accordance with NTM 51-10-01 of the fastener hole as
shown on Fig. A-SBBAA
1
 If no crack is found:
a
 In accordance with SRM 51-40-20 and SRM 51-24-00, wet install as
shown on Fig. A-SBBAA
:
1 Bolt ASNA2027T8-19 Item 1
1 Nut ASNA2531-8 Item 2
with:
Polysulfide Sealant-
General Purpose
Brushable
06AAA1 As required
b
 Report inspection results in Airbus World, refer to Appendix 07 -
Inspection Report .
c
 Perform the repetitive inspection at the interval given in the
Accomplishment Timescale paragraph 1.E.(2).
2
 If a crack is found in the fastener hole, do a cutout repair in accordance with
TASK 576120-833-942 001 Repair The Frame 40 Forward Fitting by Cutout .
D. TEST
(1) Subtask 576120-700-607-001 - Test
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 28-11-29, Page Block 401
NOTE
: This test requires the accomplishment of SUBTASK 576120-942-601 001
Close-up prior to performing this test.
(a) Do the test procedure as specified before the installation of the center tank
manhole covers 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(b) Remove the safety clips and tags and close the circuit breakers as specified after
the installation of the center tank manhole covers 147AZ and 148AZ, refer to AMM
28-11-29, Page Block 401.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 31
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A300-600
SERVICE BULLETIN
(c) Do the test procedure as specified after the installation of the center tank manhole
covers 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(2) Subtask 576120-790-602-001 - Leak Test
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 36-11-00, Page Block 401
NOTE
: This test requires the accomplishment of SUBTASK 576120-942-601 001
Close-up prior to performing this test.
(a) If previously installed in the Job Set-up, remove the safety clips and tags and close
the circuit breakers as specified after the installation of the engine air bleed supply
ducting between Frame 39 and Frame 40, refer to AMM 36-11-00, Page Block 401.
(b) If previously removed in the Job Set-up, do the leak test of the engine bleed air
system, refer to AMM 36-11-00, Page Block 401.
E. CLOSE-UP
(1) Subtask 576120-942-601-001 - Close-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Panel 147BZ, Panel 147CZ, Panel 147DZ, Panel
148CZ, Panel 148DZ, Panel 147AZ, Panel
148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 25-72-41, Page Block 401
28-11-29, Page Block 401
36-11-00, Page Block 401
(a) If you intend to accomplish an associated Repair Task during the same layover
period, the subsequent Close-up procedure is not necessary.
(b) If removed, reinstall the left and right engine bleed air duct at frame 40, refer to
AMM 36-11-00, Page Block 401.
(c) Close access doors 513AB and 613AB.
(d) Close access panels 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(e) Close access panels 147CZ and 147DZ, refer to AMM 25-72-41, Page Block 401.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 32
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A300-600
SERVICE BULLETIN
(f) Close access panels 148CZ and 148DZ, refer to AMM 25-72-41, Page Block 401.
(g) Close access panels 147BZ, refer to AMM 25-72-41, Page Block 401.
(h) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(i) Remove the access platform from under 140.
(j) Put the aircraft back to its initial configuration.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 33
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A300-600
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 34
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A300-600
SERVICE BULLETIN
Task 576120-833-942-001 - Repair The Frame 40 Forward Fitting by Cutout
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO WORK IN
OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE SAFETY PROCEDURES,
T H E R EI SAR I S KO F :
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
WARNING
: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION
(CDCCL). CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A
POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN
THE APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A
CDCCL ITEM CAN CAUSE A POSSIBLE FUEL TANK EXPLOSION.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 35
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A300-600
SERVICE BULLETIN
NOTE
: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
140
Access
Door
 513AB 613AB
Panel
 147AZ 147BZ 147CZ 147DZ 148AZ 148CZ 148DZ
Manpower
TOTAL MANHOURS
 43.50
ELAPSED TIME (HOURS)
 21.75
A. GENERAL
(1) Subtask 576120-910-603-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-31-53, Page Block 001
06-41-00, Page Block 001
20-21-12, Page Block 001
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-40-20
51-40-30
51-40-40
51-75-10
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 36
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A300-600
SERVICE BULLETIN
(a) If you find process and material specifications that you do not know in the design
drawings, refer to the cross-reference list in the Process and Material Specification
(PMS).
(b) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
the Consumable Materials List (CML).
(d) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(e) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(f) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(g) For the identification of access panels, refer to AMM 06-41-00, Page Block 001.
(h) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(i) Remove and install fasteners in accordance with SRM 51-40-20.
(j) Apply sealant in accordance with SRM 51-24-00.
(k) Renew the protective finish in accordance with SRM 51-75-10.
(l) Obtain fastener hole diameters and drill data in accordance with SRM 51-40-40.
(m) Obtain alternative and substitute fastener data in accordance with SRM 51-40-30.
(2) Subtask 576120-839-603-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 37
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A300-600
SERVICE BULLETIN
B. PREPARATION
(1) Subtask 576120-941-603-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Panel 147BZ, Panel 147CZ, Panel 147DZ, Panel
148CZ, Panel 148DZ, Panel 147AZ, Panel
148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
25-72-41, Page Block 401
28-00-00, Page Block 301
28-10-00, Page Block 301
28-11-29, Page Block 401
28-25-00, Page Block 301
36-11-00, Page Block 401
NOTE
: If you intend to accomplish this Repair Task during the same layover
period as the associated Inspection, the subsequent Preparation
procedure is not necessary. However, defueling the center, left and right
inner wing fuel tanks is required in this Preparation if the HFEC
inspection in TASK 576120-832-942 001 HFEC Inspection of the Frame
40 Forward Fitting (Option 1) was performed.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 38
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A300-600
SERVICE BULLETIN
(a) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(b) Put an access platform in position at zone 140.
(c) Defuel the center fuel tank and the left and right inner wing fuel tank, refer to AMM
28-25-00, Page Block 301.
NOTE
: Defuel the center fuel tank and the left and right inner wing fuel tank
to avoid leakage during the rototest inspection.
(d) Degas and ventilate the fuel tanks, refer to AMM 28-00-00, Page Block 301 and
AMM 28-10-00, Page Block 301.
(e) Open the access doors 513AB and 613AB.
(f) Open the access panels 147CZ and 147DZ, refer to AMM 25-72-41, Page Block
401.
(g) Open the access panels 148CZ and 148DZ, refer to AMM 25-72-41, Page Block
401.
(h) Open the access panel 147BZ, refer to AMM 25-72-41, Page Block 401.
(i) Open the access panels 147AZ and 148AZ, refer to AMM 28-11-29, Page Block
401.
(j) If necessary, remove the left and right engine bleed air duct at Frame 40, refer to
AMM 36-11-00, Page Block 401.
C. PROCEDURE
(1) Subtask 576120-833-601-001 - Repair the Crack on the LH Frame 40 Forward
Fitting by Cutout
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB
Panel 147AZ, Panel 147BZ, Panel 147CZ, Panel
147DZ
Work location
 Frame 40
Manpower Resources
Manhours
 8.00
Minimum number of person
 1
Subtask elapsed time
 8.00
Skills
 AIRFRAME
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 39
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A300-600
SERVICE BULLETIN
Material necessary to do the job
Kit 576120C01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
NAS1726-5E
 1
 NUT
NAS1726-8E
 1
 NUT
NSA5351-5-24
 1
 PIN
NSA5351-8-24
 1
 PIN
R5381079820000
 1
 FILLER
R5381079820100
 1
 COVER
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
References
Consumable Material List (CML)
Non Destructive Test Manual (NTM)
 51-10-01
51-10-02
51-10-04
51-10-08
51-10-16
51-10-18
51-70-00
Repair Instruction
 R53810798
Structural Repair Manual (SRM)
 51-21-00
51-22-00
51-23-10
51-24-00
51-27-00
51-40-20
51-40-30
51-40-40
51-40-46
51-40-50
51-40-51
51-49-00
51-70-00
51-70-20
51-71-80
51-73-10
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this repair, refer to Fig. A-SFAAA
.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 40
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A300-600
SERVICE BULLETIN
(a) Repair the crack on the Forward Fitting in accordance with:
Repair Instruction R53810798
SRM 51-27-00
SRM 51-71-80
SRM 51-40-20
SRM 51-40-30
SRM 51-40-40
SRM 51-40-46
SRM 51-40-51
SRM 51-40-50
SRM 51-70-00
SRM 51-21-00
SRM 51-22-00
SRM 51-23-10
SRM 51-24-00
SRM 51-73-10
SRM 51-49-00
SRM 51-70-20
Refer to:
NTM 51-10-08
NTM 51-10-01
NTM 51-10-18
NTM 51-10-02
NTM 51-10-04
NTM 51-10-16
NTM 51-70-00
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 41
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A300-600
SERVICE BULLETIN
(b) Wet install on the Forward Fitting in accordance with SRM 51-40-20 and SRM
51-24-00:
1 Filler R5381079820000
1 Cover Plate R5381079820100
1 Pin-Hi Lok NSA5351-8-24
1 Pin-Hi Lok NSA5351-5-24
1 Nut NAS1726-8E
1 Nut NAS1726-5E
with:
Polysulfide Sealant-
General Purpose
Brushable
06AAA1 As required
(c) Report inspection results in Airbus World, refer to Appendix 07 - Inspection Report .
(d) Perform a HFEC inspection in accordance with TASK 576120-832-944 001 HFEC
Inspection of the Frame 40 Forward Fitting After Repair by Cutout at the threshold
given in the Accomplishment Timescale paragraph 1.E.(2).
(2) Subtask 576120-833-602-001 - Repair the Crack on the RH Frame 40 Forward
Fitting by Cutout
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 613AB
Panel 148AZ, Panel 148CZ, Panel 148DZ, Panel
147BZ
Work location
 Frame 40
Manpower Resources
Manhours
 8.00
Minimum number of person
 1
Subtask elapsed time
 8.00
Skills
 AIRFRAME
Material necessary to do the job
Kit 576120C01R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
NAS1726-5E
 1
 NUT
NAS1726-8E
 1
 NUT
NSA5351-5-24
 1
 PIN
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 42
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A300-600
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
NSA5351-8-24
 1
 PIN
R5381079820000
 1
 FILLER
R5381079820100
 1
 COVER
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
References
Consumable Material List (CML)
Non Destructive Test Manual (NTM)
 51-10-01
51-10-02
51-10-04
51-10-08
51-10-16
51-10-18
51-70-00
Repair Instruction
 R53810798
Structural Repair Manual (SRM)
 51-21-00
51-22-00
51-23-10
51-24-00
51-27-00
51-40-20
51-40-30
51-40-40
51-40-46
51-40-50
51-40-51
51-49-00
51-70-00
51-70-20
51-71-80
51-73-10
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this repair, refer to Fig. A-SFAAA
.
(a) Repair the crack on the Forward Fitting in accordance with:
Repair Instruction R53810798
SRM 51-27-00
SRM 51-71-80
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 43
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A300-600
SERVICE BULLETIN
SRM 51-40-20
SRM 51-40-30
SRM 51-40-40
SRM 51-40-46
SRM 51-40-51
SRM 51-40-50
SRM 51-70-00
SRM 51-21-00
SRM 51-22-00
SRM 51-23-10
SRM 51-24-00
SRM 51-73-10
SRM 51-49-00
SRM 51-70-20
Refer to:
NTM 51-10-08
NTM 51-10-01
NTM 51-10-18
NTM 51-10-02
NTM 51-10-04
NTM 51-10-16
NTM 51-70-00
(b) Wet install on the Forward Fitting in accordance with SRM 51-40-20 and SRM
51-24-00:
1 Filler R5381079820000
1 Cover Plate R5381079820100
1 Pin-Hi Lok NSA5351-8-24
1 Pin-Hi Lok NSA5351-5-24
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 44
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A300-600
SERVICE BULLETIN
1 Nut NAS1726-8E
1 Nut NAS1726-5E
with:
Polysulfide Sealant-
General Purpose
Brushable
06AAA1 As required
(c) Report inspection results in Airbus World, refer to Appendix 07 - Inspection Report .
(d) Perform a HFEC inspection in accordance with TASK 576120-832-944 001 HFEC
Inspection of the Frame 40 Forward Fitting After Repair by Cutout at the threshold
given in the Accomplishment Timescale paragraph 1.E.(2).
D. TEST
(1) Subtask 576120-700-608-001 - Test
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 28-11-29, Page Block 401
NOTE
: This test requires the accomplishment of SUBTASK 576120-942-603 001
Close-up prior to performing this test.
(a) Do the test procedure as specified before the installation of the center tank
manhole covers 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(b) Remove the safety clips and tags and close the circuit breakers as specified after
the installation of the center tank manhole covers 147AZ and 148AZ, refer to AMM
28-11-29, Page Block 401.
(c) Do the test procedure as specified after the installation of the center tank manhole
covers 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(2) Subtask 576120-790-603-001 - Leak Test
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 36-11-00, Page Block 401
NOTE
: This test requires the accomplishment of SUBTASK 576120-942-603 001
Close-up prior to performing this test.
(a) If previously installed in the Job Set-up, remove the safety clips and tags and close
the circuit breakers as specified after the installation of the engine air bleed supply
ducting between Frame 39 and Frame 40, refer to AMM 36-11-00, Page Block 401.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 45
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A300-600
SERVICE BULLETIN
(b) If previously removed in the Job Set-up, do the leak test of the engine bleed air
system, refer to AMM 36-11-00, Page Block 401.
E. CLOSE-UP
(1) Subtask 576120-942-603-001 - Close-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Panel 147BZ, Panel 147CZ, Panel 147DZ, Panel
148CZ, Panel 148DZ, Panel 147AZ, Panel
148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 25-72-41, Page Block 401
28-11-29, Page Block 401
36-11-00, Page Block 401
(a) If removed, reinstall the left and right engine bleed air duct at frame 40, refer to
AMM 36-11-00, Page Block 401.
(b) Close access doors 513AB and 613AB.
(c) Close access panels 147AZ and 148AZ, refer to AMM 28-11-29, Page Block 401.
(d) Close access panels 147CZ and 147DZ, refer to AMM 25-72-41, Page Block 401.
(e) Close access panels 148CZ and 148DZ, refer to AMM 25-72-41, Page Block 401.
(f) Close access panel 147BZ, refer to AMM 25-72-41, Page Block 401.
(g) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(h) Remove the access platform from under 140.
(i) Put the aircraft back to its initial configuration.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 46
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A300-600
SERVICE BULLETIN
Task 576120-833-943-001 - Repair the Frame 40 Forward Fitting by Stop Drilling
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
WARNING
: YOU MUST OBEY ALL THE SAFETY PROCEDURES WHEN YOU DO WORK IN
OR NEAR A FUEL TANK. IF YOU DO NOT OBEY THE SAFETY PROCEDURES,
T H E R EI SAR I S KO F :
- DEATH OR INJURY TO PERSONS
- DAMAGE TO THE AIRCRAFT OR TO OTHER EQUIPMENT.
WARNING
: THIS PROCEDURE USES A FUEL SYSTEM ITEM THAT IS IN A CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION
(CDCCL). CDCCL IDENTIFIES AN ITEM THAT CAN BE THE SOURCE OF A
POSSIBLE FUEL TANK IGNITION. YOU MUST KEEP ALL CDCCL ITEMS IN
THE APPROVED CONFIGURATION. DAMAGE, WEAR OR CHANGES TO A
CDCCL ITEM CAN CAUSE A POSSIBLE FUEL TANK EXPLOSION.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 47
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A300-600
SERVICE BULLETIN
NOTE
: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
NOTE
: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.
NOTE
: Discarded parts must be managed at the operator’s discretion.
Task Associated Data
Zone
140
Access
Door
 513AB 613AB
Panel
 147AZ 147BZ 147CZ 147DZ 148AZ 148CZ 148DZ
Manpower
TOTAL MANHOURS
 57.50
ELAPSED TIME (HOURS)
 28.75
A. GENERAL
(1) Subtask 576120-910-604-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-21-00, Page Block 001
06-31-53, Page Block 001
06-41-00, Page Block 001
20-21-12, Page Block 001
Consumable Material List (CML)
Structural Repair Manual (SRM)
 51-24-00
51-40-00
51-40-20
51-40-30
51-40-40
51-75-10
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 48
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 55

@A300-600
SERVICE BULLETIN
(a) If you find process and material specifications that you do not know in the design
drawings, refer to the cross-reference list in the Process and Material Specification
(PMS).
(b) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.
(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
the Consumable Materials List (CML).
(d) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.
(e) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(f) For the identification of zones, refer to AMM 06-21-00, Page Block 001.
(g) For the identification of access panels, refer to AMM 06-41-00, Page Block 001.
(h) To torque tighten the standard threaded fasteners, refer to AMM 20-21-12, Page
Block 001.
(i) Remove and install fasteners in accordance with SRM 51-40-20.
(j) Apply sealant in accordance with SRM 51-24-00.
(k) Renew the protective finish in accordance with SRM 51-75-10.
(l) Obtain fastener hole diameters and drill data in accordance with SRM 51-40-40.
(m) Obtain alternative and substitute fastener data in accordance with SRM 51-40-30.
(2) Subtask 576120-839-604-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 49
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 56

@A300-600
SERVICE BULLETIN
B. PREPARATION
(1) Subtask 576120-941-604-001 - Job Set-up
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB, Door 613AB
Panel 147BZ, Panel 147CZ, Panel 147DZ, Panel
148CZ, Panel 148DZ, Panel 147AZ, Panel
148AZ
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 24-00-00, Page Block 301
25-72-41, Page Block 401
28-00-00, Page Block 301
28-10-00, Page Block 301
28-11-29, Page Block 401
28-13-21, Page Block 401
28-25-00, Page Block 301
36-11-00, Page Block 401
NOTE
: If you intend to accomplish this Repair Task during the same layover
period as the associated Inspection, the subsequent Preparation
procedure is not necessary. However, defueling the center, left and right
inner wing fuel tanks is required in this Preparation if the HFEC
inspection in TASK 576120-832-942 001 HFEC Inspection of the Frame
40 Forward Fitting (Option 1) was performed.
NOTE
: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic system s depressurized
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 50
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 57

@A300-600
SERVICE BULLETIN
(a) Make sure that the aircraft is electrically grounded, refer to AMM 24-00-00, Page
Block 301.
(b) Put an access platform in position at zone 140.
(c) Defuel the center fuel tank and the left and right inner wing fuel tank, refer to AMM
28-25-00, Page Block 301.
NOTE
: Defuel the center fuel tank and the left and right inner wing fuel tank
to avoid leakage during the rototest inspection.
(d) Degas and ventilate the fuel tanks, refer to AMM 28-00-00, Page Block 301 and
AMM 28-10-00, Page Block 301.
(e) Open the access doors 513AB and 613AB.
(f) Open the access panels 147CZ and 147DZ, refer to AMM 25-72-41, Page Block
401.
(g) Open the access panels 148CZ and 148DZ, refer to AMM 25-72-41, Page Block
401.
(h) Open the access panel 147BZ, refer to AMM 25-72-41, Page Block 401.
(i) Open the access panels 147AZ and 148AZ, refer to AMM 28-11-29, Page Block
401.
(j) Remove the applicable vapor seal in the affected area, refer to AMM 28-13-21,
Page Block 401.
(k) If necessary, remove the left and right engine bleed air duct at Frame 40, refer to
AMM 36-11-00, Page Block 401.
C. PROCEDURE
(1) Subtask 576120-833-603-001 - Repair the Crack on the LH Frame 40 Forward
Fitting by Stop Drilling
Work Zones and Access Panels
Zone
 Access/Work location
140
 Access
 Door 513AB
Panel 147AZ, Panel 147BZ, Panel 147CZ, Panel
147DZ
Work location
 Frame 40
Manpower Resources
Manhours
 15.00
Minimum number of person
 1
Subtask elapsed time
 15.00
Skills
 AIRFRAME
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 51
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 58

@A300-600
SERVICE BULLETIN
Material necessary to do the job
Kit 576120C02R01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
3
 EN6115V4-11
 1
 BOLT
4
 ASNA2529-4
 2
 NUT
5
 EN6115V4-12
 1
 BOLT
EN6115V4-3
 1
 BOLT
 (1)
EN6115V4X3
 1
 BOLT
EN6115V4Y3
 1
 BOLT
EN6115V5-3
 1
 BOLT
EN6115V5X3
 1
 BOLT
EN6115V5Y3
 1
 BOLT
R5381079920100
 1
 BRACKET
NOTE
 (1)
: The Bolts above that do not have an item number assigned, are used as
a plug. The Bolt is to be defined after drilling of the crack stop hole.
Consumable CMLC01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant-General
Purpose Brushable
06AAA1
 As required
Individual Compound -
Nitrogen Liquid
14VGC2
 As required
References
Consumable Material List (CML)
Non Destructive Test Manual (NTM)
 51-10-01
51-10-02
51-10-04
51-10-08
51-10-16
51-10-18
51-70-00
Repair Instruction
 R53810799
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 52
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 59

@A300-600
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 51-21-00
51-22-00
51-23-10
51-24-00
51-27-00
51-40-20
51-40-30
51-40-40
51-40-46
51-40-50
51-40-51
51-49-00
51-70-00
51-70-20
51-71-80
51-73-10
Fig. A-SFAAA
Flowchart
Sheet 01
NOTE
: To aid in the decision process of this repair, refer to Fig. A-SFAAA
.
(a) Stop the crack on the Forward Fitting in accordance with:
Repair Instruction R53810799
SRM 51-27-00
SRM 51-71-80
SRM 51-40-20
SRM 51-40-30
SRM 51-40-40
SRM 51-40-46
SRM 51-40-51
SRM 51-40-50
SRM 51-70-00
SRM 51-21-00
SRM 51-22-00
SRM 51-23-10
SRM 51-24-00
SRM 51-73-10
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 53
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 60

@A300-600
SERVICE BULLETIN
SRM 51-49-00
SRM 51-70-20
Refer to:
NTM 51-10-08
NTM 51-10-01
NTM 51-10-18
NTM 51-10-02
NTM 51-10-04
NTM 51-10-16
NTM 51-70-00
(b) Wet install as a plug depending on stop hole size in accordance with Repair
Instruction R53810799:
1 Bolt EN6115V4-3
or:
1 Bolt EN6115V4X3
or:
1 Bolt EN6115V4Y3
or:
1 Bolt EN6115V5-3
or:
1 Bolt EN6115V5X3
or:
1 Bolt EN6115V5Y3
with:
Individual
Compound -
Nitrogen Liquid
14VGC2 As required
(c) Wet install on the Forward Fitting in accordance with SRM 51-40-20, SRM
51-24-00, and Repair Instruction R53810799:
1 Stop Bracket R5381079920100
DATE: Apr 28/17 SERVICE BULLETIN No.: A300-57-6120
REVISION No.: 00 - Apr 28/17 Page: 54
0
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

The text continues at https://openairdocs.org/service-documents/airbus/a300-57-6120/file/372f492dca57.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
