# Airbus Service Bulletin A320-25-1BGJ

Copy: Revision 1 ("SB_A320-25-1BGJ_r01"), 58 pages: PDF https://openairdocs.org/files/sha256/9f/7a/9f7afaa97c94b547c905828aaee48c077518154b059ff54f0a6b08d4fd73e65c; text https://openairdocs.org/service-documents/airbus/a320-25-1bgj/file/9f7afaa97c94.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2019-0486, the docket of AD 2019-18-06. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A320-25-1BGJ
- Latest revision known: A320-25-1BGJ, Revision 1 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/a320-25-1bgj

## Text (58 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2019-0486, the docket of AD 2019-18-06. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 1
CONF ALL
AIRBUS S.A.S.
Customer Services
T echnical Data Support and Services
31703 Blagnac Cedex
FRANCE
 
The content of this document is the property of Airbus.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
MANDATORY MANDATORY MANDATORY
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS-
INTRODUCE NEW FIXATION FOR POHSC
MODIFICATION No.:
160418K30484

### Page 2

A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 2
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS-
INTRODUCE NEW FIXATION FOR POHSC
REVISION TRANSMITTAL SHEET
This page transmits Revision No. 01 of Service Bulletin No. A320-25-1BGJ.
A. ADDITIONAL WORK
Additional Work is required by this revision for aircraft modified by the original issue of this
Service Bulletin.
Unless otherwise stated by an Airworthiness Directive, AIRBUS recommends the Additional
Work to be accomplished within one year after the issue of this revision.
The Additional Work describes:
- Check of dimensions of the Threaded Pins against tolerances
- Replacement of the Threaded Pins and Nuts if necessary.
B. REASON
Revision No. 01 issued to:
- Transform Service Bulletin data from ATA iSpec 2200 norm to ASD S1000D norm
- Update the dimensions of the Threaded Pins
- Add an Additional Work T ask for aircraft modified by the original issue of this Service
Bulletin.
C. CHANGES
SERVICE BULLETIN
General Revised text and layout changes of this revision are
not identified with revision bars.
D. FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete
document. Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
E. HISTORY OF PREVIOUS REVISIONS
No previous revision
F. REVISION SEQUENCE
ORIGINAL: Dec 19/17
REVISION No. : 01 - Aug 21/18

### Page 3

A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 3
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS-
INTRODUCE NEW FIXATION FOR POHSC
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 160418K30484
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
B. REASON
(1) History
Several operators have reported loose or missing screws at the X-brackets, Y-
brackets and connecting plates of their Over Head Stowage Compartments (OHSC).
Investigations and a sampling program have shown that fuselage deflections (due
to pressure and temperature differences caused during a regular flight cycle) lead to
loads on the secondary X-load path in the OHSC. This is the root cause of the screws
loosening. The aircraft affected by this Service Bulletin are equipped with the Pivoting
Over Head Stowage Compartment (POHSC) design.
(2) Objective/Action
This Service Bulletin replaces the current screws in the X-brackets, Y-brackets and
connecting plates with threaded pins with applied micro-encapsulated coating and
additional self-locking nuts.
(3) Advantages
The embodiment of this Service Bulletin will improve the robustness of the POHSC
fixation system thus avoiding further unscheduled maintenance in this area.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING No
A/C OPERATION
AFFECTED
NO VENDOR SB NO
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES

### Page 4

A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 4
EVALUATION TABLE
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
NOTE: Service Bulletin must be accomplished.
D. MAINTENANCE CONFIGURATION
No specific aircraft maintenance configuration required.
E. MATERIAL PRICE INFORMATION
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Part kit 251BGJD01R01 1 3950.00 USD Threaded pins, washers, nuts
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS
Components See SB See Note Threaded pin, nut, washer
NOTE: Price information to be acquired by the given supplier.
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
DAL LAN WOW
G. CONCURRENT REQUIREMENTS
None
H. NATURE OF THE WORK
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT NO
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT YES
EQUIPMENT NO

### Page 5

A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 5
I. MANPOWER
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 42.00 h
ELAPSED TIME (HOURS) 14.50 h
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MANPOWER
TOTAL MAN-HOURS 18.50 h
ELAPSED TIME (HOURS) 9.25 h

### Page 6

A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BI-A-001-01 SHEET 1/1
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
General Overview
Page 6
J. GENERAL OVERVIEW
CONF ALL
A
Z230
Z250
Z260
Z240
FR21
FR66
A
TYPICAL A320
FAMILY AIRCRAFT
NOTE:
AREA OF MODIFICATION
ICN-A320-A-25XX1BGJ-A-FAPE3-000BI-A-001-01

### Page 7

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 7
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS-
INTRODUCE NEW FIXATION FOR POHSC
1. PLANNING INFORMATION
A. APPLICABILITY
NOTE: This Service Bulletin is only applicable to aircraft on which MOD No. 156853K17985
is embodied.
(1) Models
ON A/C 6923, 7031, 7061, 7112, 7149, 7165, 7214, 7233, 7237, 7239, 7268, 7281, 7287,
7293, 7298, 7304, 7327, 7364, 7373, 7379, 7381, 7433, 7436, 7441, 7479, 7546, 7592,
7672, 7707, 7709, 7765, 7777, 7840, 7845, 7885, 7896, 7943, 7973, 8026, 8036, 8040,
8063, 8078, 8080, 8134
321-211
CONF ALL
(2) Applicability by MSN
6923 7031 7061 7112 7149 7165 7214 7233 7237 7239 7268 7281 7287 7293 7298
7304 7327 7364 7373 7379 7381 7433 7436 7441 7479 7546 7592 7672 7707 7709
7765 7777 7840 7845 7885 7896 7943 7973 8026 8036 8040 8063 8078 8080 8134
(3) MSN by configuration
MSN CONFIGURATION
6923 7031 7061 7112 7149 7165 7214 7233 7237 7239 7268
7281 7287 7293 7298 7304 7327 7364 7373 7379 7381 7433
7436 7441 7479 7546 7592 7672 7707 7709 7765 7777 7840
7845 7885 7896 7943 7973 8026 8036 8040 8063 8078 8080
8134
001
(4) Configuration definition
Configuration 001
CONF 001 is applicable for all the aircraft affected by this Service Bulletin as a
standard configuration.
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
Several operators have reported loose or missing screws at the X-brackets, Y-
brackets and connecting plates of their Over Head Stowage Compartments (OHSC).
Investigations and a sampling program have shown that fuselage deflections (due
to pressure and temperature differences caused during a regular flight cycle) lead to
loads on the secondary X-load path in the OHSC. This is the root cause of the screws
loosening. The aircraft affected by this Service Bulletin are equipped with the Pivoting
Over Head Stowage Compartment (POHSC) design.

### Page 8

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 8
(2) Objective/Action
This Service Bulletin replaces the current screws in the X-brackets, Y-brackets and
connecting plates with threaded pins with applied micro-encapsulated coating and
additional self-locking nuts.
(3) Advantages
The embodiment of this Service Bulletin will improve the robustness of the POHSC
fixation system thus avoiding further unscheduled maintenance in this area.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
T o accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
1 Modify the Left Hand (LH) Pivoting Over Head Stowage Compartments
(POHSC's)
2 Modify the Right Hand (RH) Pivoting Over Head Stowage Compartments
(POHSC's)
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
1 Check Dimension of the Threaded Pins of the Left Hand (LH) Pivoting Over
Head Stowage Compartments (POHSC's)
2 Check Dimension of the Threaded Pins of the Right Hand (RH) POHSC's
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done within 72 months after issuance
of the original issue of this Service Bulletin.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm
the thresholds given but reference should be made to the AD for confirmation of the
mandated accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER

### Page 9

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 9
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Modify the Left Hand (LH) Pivoting Over Head Stowage
Compartments (POHSC's)
13.00 h
Modify the Right Hand (RH) Pivoting Over Head Stowage
Compartments (POHSC's)
13.00 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-Up 8.00 h
TOTAL MAN-HOURS 42.00 h
ELAPSED TIME (HOURS) 14.50 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart.
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Check Dimension of the Threaded Pins of the Left Hand
(LH) Pivoting Over Head Stowage Compartments (POHSC's)
1.25 h
Check Dimension of the Threaded Pins of the Right Hand
(RH) POHSC's
1.25 h
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 18.50 h
ELAPSED TIME (HOURS) 9.25 h

### Page 10

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 10
NOTE: The minimum man-hours necessary to accomplish this Service Bulletin
are those for the Inspection. Depending on the inspection result,
additional man-hours can apply.
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart - Additional Work
H. WEIGHT AND BALANCE
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. For the definition
of MEW and operator's items, refer to Ref. WBM.
Manufacturer's Empty Weight +0.1 kg (+0.220 lb)
Effect on Balance +1.6 kg.m (+11.573 lb.ft)
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
(1) Modification
(a) T ask set A320-A-25-XX-1BGJ-01000-93AA-A Modification
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-20-00, Page Block 001 06-31-53, Page Block 001
T ask 12-34-24-869-002 T ask 25-23-48-000-001
T ask 25-23-48-400-001
T ask 25-24-41-000-001
T ask 25-24-41-400-001
T ask 25-25-11-000-001
T ask 25-25-11-400-001
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-55-00
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
(2) Inspection - Additional Work for Aircraft Modified by Revision No. 00
(a) T ask set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT MAINTENANCE MANUAL (AMM)
06-20-00, Page Block 001 06-31-53, Page Block 001
T ask 12-34-24-869-002 T ask 25-23-48-000-001
T ask 25-23-48-400-001
T ask 25-24-41-000-001
T ask 25-24-41-400-001
T ask 25-25-11-000-001
T ask 25-25-11-400-001
ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)
20-55-00
WEIGHT AND BALANCE MANUAL (WBM)

### Page 11

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 11
STANDARDS MANUAL (SM)
K. PUBLICATION AFFECTED
AIRCRAFT MAINTENANCE MANUAL (AMM)
ILLUSTRATED PART CATALOG (IPC)
L. INDUSTRY SUPPORT INFORMATION
AIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kits
at no charge for orders placed before Oct 31/23.
AIRBUS will not credit the man-hours indicated in this Service Bulletin. They remain at
operator's charge.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: monitored.retrofit@airbus.com.

### Page 12

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 12
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
Material for task set A320-A-25-XX-1BGJ-01000-93AA-A Modification
MATERIAL QTY SEE NOTES
Part kit 251BGJD01R01 1
Material for task set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional
Work for Aircraft Modified by Revision No. 00
MATERIAL QTY SEE NOTES
Components See SB (1) (2)
NOTE(S)
(1): One COMPQ01 must be ordered for each replacement Threaded Pin, Item 10, Nut,
Item 12 and Washer, Item 15.
(2): One COMPQ02 must be ordered for each replacement Threaded Pin, Item 13, Nut,
Item 14 and Washer, Item 11.
B. TOOLING
No tools
C. CONSUMABLES
No consumables
D. LIST OF NEW PARTS
Part kit 251BGJD01R01
Cost 3950.00 USD
Availability 180 d (calendar days from receipt of order)
NOTE(S)
The availability given above is the standard lead-time from the date of your purchase
order. If items are required before this time, please include a retrofit planning
schedule with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic
conditions. The latest valid price and lead-time for ordering purposes shall be
obtained through the AIRBUS Spares portal or through a request for quotation to
airbus.kit@airbus.com.
Procurement address D4296
AIRBUS Material, Logistics and Suppliers
ATP II B
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
Phone: +49 40 743 51660
E-mail: airbus.kit@airbus.com
Internet: http://spares.airbus.com
NOTE(S)
Customers with aircraft shown in the applicability of this Service Bulletin should send
a purchase order to AIRBUS at the address given above and quote the number of this
Service Bulletin.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100 198 PIN
11 NAS1149CN832R 670 WASHER

### Page 13

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 13
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
12 MS21042-3 198 NUT
13 FAS000033-000 670 PIN
14 MS21042-08 670 NUT
15 NAS1149C0332R 198 WASHER
NOTE(S)
Part Number (PN) quantities in the kit are greater to allow for different aircraft cabin
configurations.
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components in the
related kit(s) which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin. The SM will give you the correct part number to part number relationship.
Components for task set A320-A-25-XX-1BGJ-01000-93BA-A Inspection - Addtional
Work for Aircraft Modified by Revision No. 00
Procurement address D4296
AIRBUS Material, Logistics and Suppliers Standard
Parts
Phone: +49 (0) 40 50 76 40 03
E-mail: ifd.spares@airbus.com
Internet: http://spares.airbus.com or via SPEC2000
NOTE(S)
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100(D4296) 1 PIN (1) (2)
11 NAS1149CN832R(D4296) 1 WASHER (3) (2)
12 MS21042-3 (D4296) 1 NUT (1) (2)
13 FAS000033-000(D4296) 1 PIN (3) (2)
14 MS21042-08 (D4296) 1 NUT (3) (2)
15 NAS1149CN332R(D4296) 1 WASHER (1) (2)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components in the
related kit(s) which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin. The SM will give you the correct part number to part number relationship.
(1): One COMPQ01 must be ordered for each replacement Threaded Pin, Item 10, Nut,
Item 12 and Washer, Item 15.
(2): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
(3): One COMPQ02 must be ordered for each replacement Threaded Pin, Item 13, Nut,
Item 14 and Washer, Item 11.
E. LIST OF EXISTING PARTS
No parts

### Page 14

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 14
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A320-A-25-XX-1BGJ-01000-93AA-A
Modification
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: Discarded parts must be managed at the operator’s discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 42.00 h
ELAPSED TIME (HOURS) 14.50h

### Page 15

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 15
B. PREPARATION
(1) Task A320-A-25-XX-1BGJ-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 12-34-24-869-002
T ask 25-23-48-000-001
T ask 25-24-41-000-001
T ask 25-25-11-000-001
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter 'Introduction -
Aircraft status for maintenance' in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM T ask
12-34-24-869-002.
(b) Remove the section hoses as necessary, refer to Ref. AMM T ask
25-25-11-000-001.
(c) Remove the cove light panels, refer to Ref. AMM T ask 25-23-48-000-001.
(d) Remove the cover panels, refer to Ref. AMM T ask 25-24-41-000-001.
C. PROCEDURE
(1) Task A320-A-25-XX-1BGJ-01001-920A-A - Modify the Left Hand (LH) Pivoting
Over Head Stowage Compartments (POHSC's)
CAUTION: IT WILL NOT BE NECESSARY TO REMOVE THE COMPLETE
PIVOTING OVERHEAD STORAGE COMPARTMENTS (POHSC) IF YOU
DO NOT REMOVE MORE THAN 50 PERCENT OF THE FASTENERS ON
EACH END OF THE POHSC AT THE SAME TIME.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230
240
250
260
Manpower/Resources/Skills
Man-hours 13.00 h
Minimum Number of person 2
Elapsed Time 6.50h

### Page 16

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 16
Skills Cabin
Material necessary to do the job
Part kit 251BGJD01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100 99 PIN
11 NAS1149CN832R 335 WASHER
12 MS21042-3 99 NUT
13 FAS000033-000 335 PIN
14 MS21042-08 335 NUT
15 NAS1149C0332R 99 WASHER
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 00106-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the LH POHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig. Modification of the LH/
RH POHSC's SHEET 2, View C and Section A-A:
As required Washer   Item (15) Discard
As required Screw   Item (1) Discard
NOTE: T o make sure the X-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to X-
Bracket misalignment.
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the LH POHSC's, on the X-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 2, View
C and Section B-B, install:
99 PIN-THREADED FAS000033-100 Item 10
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.

### Page 17

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 17
1 T orque tighten the Threaded Pins, Item 10, to between 1.1 and 1.3 Nm
(9.73 and 11.50 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(d) On the LH POHSC's, on the X-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 2, View
C and Section B-B, install:
99 WASHER NAS1149C0332R Item 15
99 NUT MS21042-3 Item 12
NOTE: The quantity of Washers, Item 15, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 T orque tighten the Nuts, Item 12, to between 2.0 and 2.5 Nm (17.70 and
22.13 lbf.in.).
(e) From the LH POHSC's, remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig. Modification of the LH/
RH POHSC's SHEET 3, View D and Section C-C:
As required Washer   Item (3) Discard
As required Screw   Item (11) Discard
NOTE: T o make sure the Y-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to Y-
Bracket misalignment.
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the LH POHSC's, on the Y-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 3, View
D and Section D-D, install:
176 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(g) On the LH POHSC's, on the Y-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 3, View
D and Section D-D, install:
176 WASHER NAS1149CN832R Item 11
176 NUT MS21042-08 Item 14
NOTE: The quantity of Washers, Item 11, and Nuts, Item 14, given above is the
maximum required and can change on different aircraft cabin layouts.

### Page 18

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 18
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(h) From the LH POHSC's, remove the fasteners from the Inter-Bin Connecting Plates
(ICP), refer to Ref. Fig. Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig.
Modification of the LH/RH POHSC's SHEET 4, View E and Section E-E:
As required Washer   Item (3) Discard
As required Screw   Item (11) Discard
NOTE: T o make sure the ICP is correctly aligned. It is recommended to remove
the fastener and install the replacement threaded pin one fastener at a
time. Removal of all fasteners at one time can lead to ICP misalignment.
(i) On the LH POHSC's, on the ICP, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 4, View
E and Section F-F, install:
159 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(j) On the LH POHSC's, on the ICP, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 4, View
E and Section F-F, install:
159 WASHER NAS1149CN832R Item 11
159 NUT MS21042-08 Item 14
NOTE: The quantity of Washers, Item 11, and Nuts, Item 14, given above is the
maximum required and can change on different aircraft cabin layouts.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).

### Page 19

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BE-A-002-01 SHEET 1/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 19
CONF ALL
A
B
Z260
Z250
Z230
Z240
FR43
FR47
FR47.5
FR51
FR55
B
C
D
DD
D
FR47.2
FR59
FR64D
C
C
C
C D
E
E
E
FR43
FR34
FR35.1
FR30
FR26
A
C
C
C
C
C
C
D
E
D
D
D
D
D
D
E E
FR21
FR35.3
FR35.5
FR35.7
FR39
E
C
E
E
E
E
CD
C
C
D
C
D
D
C
DC
E
E
E
C
D
DC
C
C
D
D
C
D
C
D
C
D
C
D
CE
E
E
C
D
D
TYPICAL
01
NOTE:
DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE01
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
TYPICAL
01
ICN-A320-A-25XX1BGJ-A-FAPE3-000BE-A-002-01

### Page 20

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BF-A-005-01 SHEET 2/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 20
CONF ALL
15
INSERT
X-BRACKET
(15)
BOTTOM
PANEL
(1)
BACK
PANEL
A A
INSERT
BACK
PANEL
BOTTOM
PANEL
X-BRACKET
B B
BEFORE
AFTER
C
12
10
A
A
B
B
TYPICAL X-BRACKET
(6 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
02
03
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED02
NOTE:
PIN, ITEM 10, MUST BE BETWEEN 12.00 mm (0.472 in) AND 15.00 mm (0.591 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.80 mm (0.150 in).
ICN-A320-A-25XX1BGJ-A-FAPE3-000BF-A-005-01

### Page 21

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BG-A-006-01 SHEET 3/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 21
CONF ALL
Y-BRACKET (3) (3)
SIDEWALL
BOTTOM
PANEL
SIDEWALL
BOTTOM
PANEL
11
14
13
11
14
13
Y-BRACKET
BEFORE
AFTER
INSERT
INSERT
D
C C
D D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
C
C
D
D
AFFECTED
FASTENERS
AFFECTED
FASTENERS
04
05
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED04
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
(11) (11)
ICN-A320-A-25XX1BGJ-A-FAPE3-000BG-A-006-01

### Page 22

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BH-A-005-01 SHEET 4/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 22
CONF ALL
SIDEWALL
TOP/BOTTOM
PANEL
11
14
13
11
14
13
AFTER
CONNECTING
PLATE
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
INSERT
E
E
F
F
E
F F
TYPICAL
AFFECTED
FASTENERS
AFFECTED
FASTENERS
(3) (3)
SIDEWALL
BEFORE
CONNECTING
PLATE
TOP/BOTTOM
PANEL
INSERT
E E
06
07
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED06
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
(11) (11)
ICN-A320-A-25XX1BGJ-A-FAPE3-000BH-A-005-01

### Page 23

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 23
(2) Task A320-A-25-XX-1BGJ-02001-920A-A - Modify the Right Hand (RH) Pivoting
Over Head Stowage Compartments (POHSC's)
CAUTION: IT WILL NOT BE NECESSARY TO REMOVE THE COMPLETE
PIVOTING OVERHEAD STORAGE COMPARTMENTS (POHSC) IF YOU
DO NOT REMOVE MORE THAN 50 PERCENT OF THE FASTENERS ON
EACH END OF THE POHSC AT THE SAME TIME.
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230
240
250
260
Manpower/Resources/Skills
Man-hours 13.00 h
Minimum Number of person 2
Elapsed Time 6.50h
Skills Cabin
Material necessary to do the job
Part kit 251BGJD01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100 99 PIN
11 NAS1149CN832R 335 WASHER
12 MS21042-3 99 NUT
13 FAS000033-000 335 PIN
14 MS21042-08 335 NUT
15 NAS1149C0332R 99 WASHER
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 00106-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.

### Page 24

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 24
(b) From the RH POHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig. Modification of the LH/
RH POHSC's SHEET 2, View C and Section A-A:
As required Washer   Item (15) Discard
As required Screw   Item (1) Discard
NOTE: T o make sure the X-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to X-
Bracket misalignment.
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the RH POHSC's, on the X-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 2, View
C and Section B-B, install:
99 PIN-THREADED FAS000033-100 Item 10
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 T orque tighten the Threaded Pins, Item 10, to between 1.1 and 1.3 Nm
(9.73 and 11.50 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(d) On the RH POHSC's, on the X-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 2, View
C and Section B-B, install:
99 WASHER NAS1149C0332R Item 15
99 NUT MS21042-3 Item 12
NOTE: The quantity of Washers, Item 15, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 T orque tighten the Nuts, Item 12, to between 2.0 and 2.5 Nm (17.70 and
22.13 lbf.in.).
(e) From the RH POHSC's, remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig. Modification of the LH/
RH POHSC's SHEET 3, View D and Section C-C:
As required Washer   Item (3) Discard
As required Screw   Item (11) Discard
NOTE: T o make sure the Y-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to Y-
Bracket misalignment.
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.

### Page 25

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 25
(f) On the RH POHSC's, on the Y-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 3, View
D and Section D-D, install:
176 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(g) On the RH POHSC's, on the Y-Brackets, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 3, View
D and Section D-D, install:
176 WASHER NAS1149CN832R Item 11
176 NUT MS21042-08 Item 14
NOTE: The quantity of Washers, Item 11, and Nuts, Item 14, given above is the
maximum required and can change on different aircraft cabin layouts.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(h) From the RH POHSC's, remove the fasteners from the Inter-Bin Connecting Plates
(ICP), refer to Ref. Fig. Modification of the LH/RH POHSC's SHEET 1 and Ref. Fig.
Modification of the LH/RH POHSC's SHEET 4, View E and Section E-E:
As required Washer   Item (3) Discard
As required Screw   Item (11) Discard
NOTE: T o make sure the ICP is correctly aligned. It is recommended to remove
the fastener and install the replacement threaded pin one fastener at a
time. Removal of all fasteners at one time can lead to ICP misalignment.
(i) On the RH POHSC's, on the ICP, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 4, View
E and Section F-F, install:
159 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(j) On the RH POHSC's, on the ICP, refer to Ref. Fig. Modification of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Modification of the LH/RH POHSC's SHEET 4, View
E and Section F-F, install:
159 WASHER NAS1149CN832R Item 11

### Page 26

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 26
159 NUT MS21042-08 Item 14
NOTE: The quantity of Washers, Item 11, and Nuts, Item 14, given above is the
maximum required and can change on different aircraft cabin layouts.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).

### Page 27

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BE-A-002-01 SHEET 1/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 27
CONF ALL
A
B
Z260
Z250
Z230
Z240
FR43
FR47
FR47.5
FR51
FR55
B
C
D
DD
D
FR47.2
FR59
FR64D
C
C
C
C D
E
E
E
FR43
FR34
FR35.1
FR30
FR26
A
C
C
C
C
C
C
D
E
D
D
D
D
D
D
E E
FR21
FR35.3
FR35.5
FR35.7
FR39
E
C
E
E
E
E
CD
C
C
D
C
D
D
C
DC
E
E
E
C
D
DC
C
C
D
D
C
D
C
D
C
D
C
D
CE
E
E
C
D
D
TYPICAL
01
NOTE:
DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE01
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
TYPICAL
01
ICN-A320-A-25XX1BGJ-A-FAPE3-000BE-A-002-01

### Page 28

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BF-A-005-01 SHEET 2/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 28
CONF ALL
15
INSERT
X-BRACKET
(15)
BOTTOM
PANEL
(1)
BACK
PANEL
A A
INSERT
BACK
PANEL
BOTTOM
PANEL
X-BRACKET
B B
BEFORE
AFTER
C
12
10
A
A
B
B
TYPICAL X-BRACKET
(6 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
02
03
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED02
NOTE:
PIN, ITEM 10, MUST BE BETWEEN 12.00 mm (0.472 in) AND 15.00 mm (0.591 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.80 mm (0.150 in).
ICN-A320-A-25XX1BGJ-A-FAPE3-000BF-A-005-01

### Page 29

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BG-A-006-01 SHEET 3/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 29
CONF ALL
Y-BRACKET (3) (3)
SIDEWALL
BOTTOM
PANEL
SIDEWALL
BOTTOM
PANEL
11
14
13
11
14
13
Y-BRACKET
BEFORE
AFTER
INSERT
INSERT
D
C C
D D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
C
C
D
D
AFFECTED
FASTENERS
AFFECTED
FASTENERS
04
05
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED04
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
(11) (11)
ICN-A320-A-25XX1BGJ-A-FAPE3-000BG-A-006-01

### Page 30

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BH-A-005-01 SHEET 4/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Modification of the LH/RH POHSC's
Page 30
CONF ALL
SIDEWALL
TOP/BOTTOM
PANEL
11
14
13
11
14
13
AFTER
CONNECTING
PLATE
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
INSERT
E
E
F
F
E
F F
TYPICAL
AFFECTED
FASTENERS
AFFECTED
FASTENERS
(3) (3)
SIDEWALL
BEFORE
CONNECTING
PLATE
TOP/BOTTOM
PANEL
INSERT
E E
06
07
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED06
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
(11) (11)
ICN-A320-A-25XX1BGJ-A-FAPE3-000BH-A-005-01

### Page 31

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 31
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A320-A-25-XX-1BGJ-01001-740A-A - Close-Up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 25-23-48-400-001
T ask 25-24-41-400-001
T ask 25-25-11-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the cover panels, refer to Ref. AMM T ask 25-24-41-400-001.
(c) Install the cove light panels, refer to Ref. AMM T ask 25-23-48-400-001.
(d) Install the section hoses, refer to Ref. AMM T ask 25-25-11-400-001.
(e) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-25-XX-1BGJ-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 32

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 32
Task set A320-A-25-XX-1BGJ-01000-93BA-A
Inspection - Addtional Work for Aircraft Modified by Revision No. 00
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL
WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
NOTE: This Service Bulletin is classified mandatory or expected to be classified mandatory by
an Airworthiness Directive (AD). The paragraphs 3.C. and 3.E. in these accomplishment
instructions are Required for Compliance (RC) and must be done to comply with the AD.
T o allow more flexibility, the rule "refer to" and "in accordance with" will apply to these
paragraphs 3.C. and 3.E. Other paragraphs are recommended and may be deviated from,
done as part of other actions or done with accepted methods different from those given
in the Service Bulletin, as long as the RC paragraphs can be done and the aircraft can be
put back into a serviceable condition.
NOTE: Discarded parts must be managed at the operator's discretion.
A. TASK SET ASSOCIATED INFORMATION
Task Manpower
TOTAL MAN-HOURS 18.50 h
ELAPSED TIME (HOURS) 9.25h

### Page 33

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 33
B. PREPARATION
(1) Task A320-A-25-XX-1BGJ-03001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 12-34-24-869-002
T ask 25-23-48-000-001
T ask 25-24-41-000-001
T ask 25-25-11-000-001
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter "Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM T ask
12-34-24-869-002.
(b) Remove the section hoses as necessary, refer to Ref. AMM T ask
25-25-11-000-001.
(c) Remove the cove light panels, refer to Ref. AMM T ask 25-23-48-000-001.
(d) Remove the cover panels, refer to Ref. AMM T ask 25-24-41-000-001.
C. PROCEDURE
(1) Task A320-A-25-XX-1BGJ-01001-361A-A - Check Dimension of the Threaded
Pins of the Left Hand (LH) Pivoting Over Head Stowage Compartments
(POHSC's)
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230
240
250
260
Manpower/Resources/Skills
Man-hours 1.25 h
Minimum Number of person 1
Elapsed Time 1.25h
Skills Cabin

### Page 34

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 34
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100 1 PIN (1)
11 NAS1149CN832R 1 WASHER (1)
12 MS21042-3 1 NUT (1)
13 FAS000033-000 1 PIN (1)
14 MS21042-08 1 NUT (1)
15 NAS1149CN332R 1 WASHER (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 00106-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, do a check of the dimensions of all the Threaded Pins,
Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the
LH/RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's
SHEET 2, View C and Section A-A, carefully remove:
1 Pin-Threaded   Item (10) Discard
1 Washer   Item (15) Discard
1 Nut   Item (12) Discard
NOTE: T o make sure the X-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to X-
Bracket misalignment.

### Page 35

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 35
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, clean any remains of adhesive from the inserts.
(e) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, install:
1 PIN-THREADED FAS000033-100 Item 10
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Threaded Pins, Item 10, to between 1.1 and 1.3 Nm
(9.73 and 11.50 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, install:
1 WASHER NAS1149CN332R Item 15
1 NUT MS21042-3 Item 12
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Nuts, Item 12, to between 2.0 and 2.5 Nm (17.70 and
22.13 lbf.in.).
(h) On the X-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, do a check of the dimensions of all the new Threaded
Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the dimensions of all the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).

### Page 36

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 36
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the
LH/RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's
SHEET 3, View D and Section B-B, carefully remove:
1 Pin-Threaded   Item (13) Discard
1 Washer   Item (14) Discard
1 Nut   Item (11) Discard
NOTE: T o make sure the Y-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to Y-
Bracket misalignment.
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, clean any remains of adhesive from the inserts.
(l) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, install:
1 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, install:
1 NUT MS21042-08 Item 14
1 WASHER NAS1149CN832R Item 11
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).

### Page 37

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 37
(o) On the Y-Brackets of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the dimensions of all the new Threaded
Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the dimensions of all the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
T ask A320-A-25-XX-1BGJ-02ZZZ-361Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, carefully remove:
1 Pin-Threaded   Item (13) Discard
1 Washer   Item (14) Discard
1 Nut   Item (11) Discard
NOTE: T o make sure the ICP is correctly aligned. It is recommended to remove
the fastener and install the replacement threaded pin one fastener at a
time. Removal of all fasteners at one time can lead to ICP misalignment.
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, install:
1 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.

### Page 38

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 38
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, install:
1 NUT MS21042-08 Item 14
1 WASHER NAS1149CN832R Item 11
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(v) On the ICP of the LH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the dimensions of all the new Threaded
Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
Ref. T ask A320-A-25-XX-1BGJ-02ZZZ-361Z-A.
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (q) thru (v).

### Page 39

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090I-A-002-01 SHEET 1/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 39
CONF ALL
A
B
Z260
Z250
Z230
Z240
FR43
FR47
FR47.5
FR51
FR55
B
C
D
DD
D
FR47.2
FR59
FR64D
C
C
C
C D
E
E
E
FR43
FR34
FR35.1
FR30
FR26
A
C
C
C
C
C
C
D
E
D
D
D
D
D
D
E E
FR21
FR35.3
FR35.5
FR35.7
FR39
E
C
E
E
E
E
CD
C
C
D
C
D
D
C
DC
E
E
E
C
D
DC
C
C
D
D
C
D
C
D
C
D
C
D
CE
E
E
C
D
D
TYPICAL
01
NOTE:
DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE01
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
TYPICAL
01
ICN-A320-A-25XX1BGJ-A-FAPE3-0090I-A-002-01

### Page 40

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090J-A-002-01 SHEET 2/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 40
CONF ALL
INSERT
BACK
PANEL
BOTTOM
PANEL
X-BRACKET
C
A
A
TYPICAL X-BRACKET
(6 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
02
03
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED02
NOTE:
PIN, ITEM 10, MUST BE BETWEEN 12.00 mm (0.472 in) AND 15.00 mm (0.591 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.80 mm (0.150 in).
A A
(10)
10 (12)
12
(15)
ICN-A320-A-25XX1BGJ-A-FAPE3-0090J-A-002-01

### Page 41

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090K-A-002-01 SHEET 3/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 41
CONF ALL
SIDEWALL
BOTTOM
PANEL
(11)(11)
Y-BRACKET
INSERT
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
04
05
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED04
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
B B
B
B
(14)
14
(13)
13
(14)
14
(13)
13
ICN-A320-A-25XX1BGJ-A-FAPE3-0090K-A-002-01

### Page 42

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090L-A-002-01 SHEET 4/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 42
CONF ALL
SIDEWALL
TOP/BOTTOM
PANEL
(11)
CONNECTING
PLATE
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
INSERT
E
TYPICAL
AFFECTED
FASTENERS
AFFECTED
FASTENERS
06
07
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED06
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
C
C
C C
(14)
14
(13)
13
(11)
(14)
14
(13)
13
ICN-A320-A-25XX1BGJ-A-FAPE3-0090L-A-002-01

### Page 43

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 43
(2) Task A320-A-25-XX-1BGJ-02001-361A-A - Check Dimension of the Threaded
Pins of the Right Hand (RH) POHSC's
Job Set-Up Information
Working Area
Impacted Zone Access / Work Location
230
240
250
260
Manpower/Resources/Skills
Man-hours 1.25 h
Minimum Number of person 1
Elapsed Time 1.25h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-100 1 PIN (1)
11 NAS1149CN832R 1 WASHER (1)
12 MS21042-3 1 NUT (1)
13 FAS000033-000 1 PIN (1)
14 MS21042-08 1 NUT (1)
15 NAS1149CN332R 1 WASHER (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 00106-31-53, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 T ag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET

### Page 44

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 44
2, View C and Section A-A, do a check of the dimensions of all the Threaded Pins,
Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the
LH/RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's
SHEET 2, View C and Section B-B, carefully remove:
1 Pin-Threaded   Item (10) Discard
1 Washer   Item (15) Discard
1 Nut   Item (12) Discard
NOTE: T o make sure the X-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to X-
Bracket misalignment.
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, clean any remains of adhesive from the inserts.
(e) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, install:
1 PIN-THREADED FAS000033-100 Item 10
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Threaded Pins, Item 10, to between 1.1 –and 1.3 Nm
(9.73 and 11.50 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, install:
1 WASHER NAS1149CN332R Item 15
1 NUT MS21042-3 Item 12

### Page 45

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 45
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Nuts, Item 12, to between 2.0 and 2.5 Nm (17.70 and
22.13 lbf.in.).
(h) On the X-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
2, View C and Section A-A, do a check of the dimensions of all the new Threaded
Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the dimensions of all the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the
LH/RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's
SHEET 3, View D and Section B-B, carefully remove:
1 Pin-Threaded   Item (13) Discard
1 Washer   Item (14) Discard
1 Nut   Item (11) Discard
NOTE: T o make sure the Y-Bracket is correctly aligned. It is recommended
to remove the fastener and install the replacement threaded pin one
fastener at a time. Removal of all fasteners at one time can lead to Y-
Bracket misalignment.
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, clean any remains of adhesive from the inserts.
(l) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, install:
1 PIN-THREADED FAS000033-000 Item 13

### Page 46

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 46
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, install:
1 NUT MS21042-08 Item 14
1 WASHER NAS1149CN832R Item 11
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(o) On the Y-Brackets of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/
RH POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET
3, View D and Section B-B, do a check of the dimensions of all the new Threaded
Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the dimensions of all the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
T ask A320-A-25-XX-1BGJ-03ZZZ-740Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, carefully remove:
1 Pin-Threaded   Item (13) Discard
1 Washer   Item (14) Discard
1 Nut   Item (11) Discard
NOTE: T o make sure the ICP is correctly aligned. It is recommended to remove
the fastener and install the replacement threaded pin one fastener at a
time. Removal of all fasteners at one time can lead to ICP misalignment.
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.

### Page 47

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 47
(r) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, install:
1 PIN-THREADED FAS000033-000 Item 13
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, install:
1 NUT MS21042-08 Item 14
1 WASHER NAS1149CN832R Item 11
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 T orque the Nuts, Item 14, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(v) On the ICP of the RH POHSC's, refer to Ref. Fig. Additional Work of the LH/RH
POHSC's SHEET 1 and Ref. Fig. Additional Work of the LH/RH POHSC's SHEET 4,
View E and Section C-C, do a check of the dimensions of all the new Threaded
Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
Ref. T ask A320-A-25-XX-1BGJ-03ZZZ-740Z-A.
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (q) thru (v).

### Page 48

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090I-A-002-01 SHEET 1/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 48
CONF ALL
A
B
Z260
Z250
Z230
Z240
FR43
FR47
FR47.5
FR51
FR55
B
C
D
DD
D
FR47.2
FR59
FR64D
C
C
C
C D
E
E
E
FR43
FR34
FR35.1
FR30
FR26
A
C
C
C
C
C
C
D
E
D
D
D
D
D
D
E E
FR21
FR35.3
FR35.5
FR35.7
FR39
E
C
E
E
E
E
CD
C
C
D
C
D
D
C
DC
E
E
E
C
D
DC
C
C
D
D
C
D
C
D
C
D
C
D
CE
E
E
C
D
D
TYPICAL
01
NOTE:
DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE01
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
TYPICAL
01
ICN-A320-A-25XX1BGJ-A-FAPE3-0090I-A-002-01

### Page 49

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090J-A-002-01 SHEET 2/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 49
CONF ALL
INSERT
BACK
PANEL
BOTTOM
PANEL
X-BRACKET
C
A
A
TYPICAL X-BRACKET
(6 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
02
03
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED02
NOTE:
PIN, ITEM 10, MUST BE BETWEEN 12.00 mm (0.472 in) AND 15.00 mm (0.591 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.80 mm (0.150 in).
A A
(10)
10 (12)
12
(15)
ICN-A320-A-25XX1BGJ-A-FAPE3-0090J-A-002-01

### Page 50

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090K-A-002-01 SHEET 3/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 50
CONF ALL
SIDEWALL
BOTTOM
PANEL
(11)(11)
Y-BRACKET
INSERT
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
AFFECTED
FASTENERS
AFFECTED
FASTENERS
04
05
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED04
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
B B
B
B
(14)
14
(13)
13
(14)
14
(13)
13
ICN-A320-A-25XX1BGJ-A-FAPE3-0090K-A-002-01

### Page 51

A318/A319/A320/A321
SERVICE BULLETIN
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0090L-A-002-01 SHEET 4/4
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Additional Work of the LH/RH POHSC's
Page 51
CONF ALL
SIDEWALL
TOP/BOTTOM
PANEL
(11)
CONNECTING
PLATE
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
INSERT
E
TYPICAL
AFFECTED
FASTENERS
AFFECTED
FASTENERS
06
07
THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED06
NOTE:
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 14, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
C
C
C C
(14)
14
(13)
13
(11)
(14)
14
(13)
13
ICN-A320-A-25XX1BGJ-A-FAPE3-0090L-A-002-01

### Page 52

A318/A319/A320/A321
SERVICE BULLETIN
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 52
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A320-A-25-XX-1BGJ-03001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
AMM
T ask 25-23-48-400-001
T ask 25-24-41-400-001
T ask 25-25-11-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the cover panels, refer to Ref. AMM T ask 25-24-41-400-001.
(c) Install the cove light panels, refer to Ref. AMM T ask 25-23-48-400-001.
(d) Install the section hoses, refer to Ref. AMM T ask 25-25-11-400-001.
(e) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-25-XX-1BGJ-03001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

### Page 53

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 53
APPENDIX
A. Manpower Gantt Chart
Manpower Gantt Chart
For an explanation of the man-hours and elapsed time, refer to the next page(s).

### Page 54

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-000BD-A-004-01 SHEET 1/1
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Manpower Gantt Chart
Page 54
CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGJ
GET ACCESS
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
42.00
14.50
STEPS
8.00 4.00
0
MODIFY THE LEFT HAND (LH) 13.00 6.50
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTES:
PER
2
2
:
:
SB ELAPSED TIME
(HOURS)
4 8
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
13.00 6.502
CLOSE-UP 8.00 4.002
2 6 10 12 14
PIVOTING OVER HEAD
STORAGE COMPARTMENTS
(POHSC'S)
MODIFY THE RIGHT HAND
(RH) PIVOTING OVER HEAD
STORAGE COMPARTMENTS
(POHSC'S)
ICN-A320-A-25XX1BGJ-A-FAPE3-000BD-A-004-01

### Page 55

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 55
B. Manpower Gantt Chart - Additional Work
Manpower Gantt Chart - Additional Work
For an explanation of the man-hours and elapsed time, refer to the next page(s).

### Page 56

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
Figure ICN-A320-A-25XX1BGJ-A-FAPE3-0095K-A-001-01 SHEET 1/1
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18
Manpower Gantt Chart - Additional Work
Page 56
CONF ALL
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGJ
GET ACCESS
MH ET/S
TOTAL MANHOURS
SB ELAPSED TIME
18.50
9.25
STEPS
8.00 4.00
0
CHECK DIMENSION OF THE 1.25 1.25
MH
ET/S:
PER
MANHOURS
ELAPSED TIME PER STEP
NUMBER OF PERSONS
01
02
THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
01
02
NOTES:
PER
2
1
:
:
SB ELAPSED TIME
(HOURS)
4 6
IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ARE NOT REFLECTED IN THIS GANTT CHART.
1.25 1.251
CLOSE-UP 8.00 4.002
3 5 7 8 9
THREADED PINS OF THE
LEFT HAND (LH) PIVOTING
OVER HEAD STORAGE
CHECK DIMENSION OF THE
THREADED PINS OF THE
RIGHT HAND (RH) POHSC'S
COMPARTMENTS (POHSC'S)
21
ICN-A320-A-25XX1BGJ-A-FAPE3-0095K-A-001-01

### Page 57

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 57
C. REPORTING SHEET
TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS-
INTRODUCE NEW FIXATION FOR POHSC
MODIFICATION No.: 160418K30484
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:
- For complete information on reporting means to Airbus, Question 2 "What are
the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

### Page 58

A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
REV 00 Dec 19/17 A320-25-1BGJ
REV 01 Aug 21/18 Page 58
D. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.
Quality rating of this SB 4 3 2 1
Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y / N
NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Planning Material Instructions
X Applicability X T ooling X Preparation
X Reason X List of Materials
Operator Supplied
X Mod/Inspection
X Manpower X Kit content X T est
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS CUSTOMER SERVICES DIRECTORATE
Service Bulletins Management
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Fax: (+33) 5 61 93 42 51
Or via your Resident Customer Support Office.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
