# Airbus Service Bulletin A32N023-21: No revision named

- Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-1075, the docket of AD 2022-12-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Airbus Service Bulletin A32N023-21](https://openairdocs.org/service-documents/airbus/a32n023-21.md)
- Title as filed: A32N023-21-00
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/c5/31/c531de239ba6d3676e36496e53210afa94c7f3d1c522cfae303ca82f356bf260
- Page: https://openairdocs.org/service-documents/airbus/a32n023-21/file/c531de239ba6

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

CUSTOMER SERVICES DIRECTORATE
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC FRANCE
TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT
AOT ref: A32N023-21 Rev 00 Page 1 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
SUBJECT: ATA 32 – MLG sliding tube : repetitive inspection at jacking dome area
AIRCRAFT TYPE: A318, A319, A320, A321
OUR REF.: A32N023-21 Rev 00 dated 05-MAY-2021
EFFECTIVITY DATE: 15 May 2021
1. AIRCRAFT AFFECTED
All A318, A319, A320, A321 Aircraft. 
A320 Family NEO Aircraft are not affected by the content of this AOT. 
2. REFERENCED DOCUMENTATION
2.1 APPENDIX
- Appendix 1: List of suspected MLG sliding tubes SN. 
- Appendix 2: List of suspected MLG leg and dressings SN. 
- Appendix 3: Inspection reporting sheet. 
2.2 REFERENCES
- Ref.1: AOT A32N020-20 Rev 00 dated of 17 June 2020.
- Ref 2. Airworthiness Directive (AD) EASA 2020-0193 dated of 07 September 2020.
- Ref.3: Airworthiness Directive (AD) FAA 2020-21-09 dated of 30 October 2020. 
- Ref.4: AOT A32N022-20 Rev 01 dated of 16 November 2020. 
- Ref 5: Airworthiness Directive (AD) EASA 2020-0258 (Correction) dated of 19 November 2020. 
- Ref 6: Airworthiness Directive (AD) FAA 2020-26-01 dated of 18 December 2020. 
- Ref.7: AMM task 12-34-24-869-002 “Aircraft Grounding (Earthing) for the Maintenance Operations”.
- Ref.8: AMM task 32-11-00-100-002 “Cleaning of the Main Landing Gear”.
- Ref.9: AMM task 32-11-13-000-004 “Removal of the Sliding Tube Sub-Assembly of the MLG Shock
Absorber “.
- Ref.10: AMM task 32-11-13-400-004 “Installation of the Sliding Tube Sub-Assembly of the MLG Shock 
Absorber”.
3. REASON
Two cases of MLG sliding tubes cracked at jacking dome area have been reported during their second 
overhaul since their entry into service. 
 
Investigations of the second reported case have led to identify a batch of MLG sliding tubes on which 
non detection of corrosion pits during overhaul could be suspected.
The purpose of this AOT is to request the operators to perform a repetitive General Visual Inspection 
(GVI) of MLG sliding tubes at jacking dome area on this identified batch. 
3.1 FACTS
Beginning of June 2020, two A320 MLG sliding tubes were found with a significant crack during their 
second overhaul since their entry into service.

### Page 2

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 2 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Both cracks extended between the jacking dome bore and the 2M harness hole as shown in Figure 1. 
Figure 1: Crack found on one MLG sliding tube at jacking dome area in June 2020.
The cracked MLG sliding tubes have accumulated respectively 26652 FC and 35894 FC and had 
previously been overhauled in 2010 in two different Maintenance and Repair Organization (MRO). 
Pending investigation results and as a precaution, Airbus issued an AOT (Ref.1) which was 
subsequently mandated (Ref. 2, Ref .3), to request a one-off GVI of the suspected at-risk population of 
MLG sliding tubes.
Completion of the laboratory investigations of the two MLG sliding tubes have demonstrated two 
different root causes. 
- For the first reported case: 
Laboratory investigations have identified that the crack had initiated from thermal abuse due to an 
incorrectly performed Magnetic Particle Inspection (MPI) operation at previous overhaul. 
Investigations have led to identify a batch of MLG sliding tubes on which thermal abuse during overhaul 
could be suspected. Airbus has issued a dedicated AOT (Ref.4) which was subsequently mandated 
(Ref.5, Ref.6), to request the operators to perform a repetitive GVI at jacking dome area on this identified 
batch.
- For the second reported case: 
Laboratory investigations have identified that the crack had initiated from corrosion pits in the jacking 
dome bore of the MLG sliding tube that were not detected during the previous overhaul in 2010.
The MRO which had performed this previous overhaul, stopped activity at the end of 2014.

### Page 3

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 3 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Investigations have been conducted to review the overhaul activity of MLG sliding tubes that have 
passed through this MRO, during its period of activity (September 2008 until end of 2014). 
These investigations have led to identify a batch of MLG sliding tubes on which non detection of 
corrosion pits at jacking dome bore during overhaul could be suspected.
This identified batch is composed of: 
- A list of MLG sliding tubes SN (Appendix 1) and, 
- A list of MLG leg and dressings SN (Appendix 2), as the PN and SN of the MLG sliding tubes 
fitted on these MLG leg and dressings have not been identified. 
 
3.2 CONSEQUENCES
An undetected crack on the MLG sliding tube at the jacking dome area could lead to the rupture of the
MLG sliding tube during operations.
3.3 AIM
The aim of this AOT is to request operators to perform a repetitive General Visual Inspection (GVI) of 
MLG sliding tubes listed in Appendix 1 and of the MLG sliding tubes fitted on MLG leg and dressings 
listed in Appendix 2, to ensure that no crack is present in the area around the jacking dome. 
This GVI shall be repeated until the next MLG sliding tube overhaul.
4. SHORT TERM ACTION
NOTE: This AOT is classified mandatory or expected to be classified mandatory by an Airworthiness 
Directive (AD). The accomplishment instructions marked as Required for Compliance (RC) must be done 
to comply with the AD. “RC” is indicating these paragraphs accordingly. 
NOTE: The accomplishment instructions of this AOT include procedures given in other documents or in 
other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted 
by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in 
accordance with’ are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this AOT do not 
constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit 
or add access and/or close-up steps to add flexibility to their maintenance operations as long as the 
technical intent of the AOT is met within the set parameters.
4.1 PLANNING AND MANPOWER
4.1.1 ACCOMPLISHMENT TIMESCALE (RC)
The MLG sliding tubes fitted on affected aircraft (refer to paragraph 1.) shall be inspected as per 
procedure defined in paragraph 4.2.2., at the earliest opportunity without exceeding 500 FC from the 
effective date of this AOT. 
For the MLG sliding tubes listed in Appendix 1 and for the MLG sliding tubes fitted on MLG leg and 
dressings listed in Appendix 2, inspection as per paragraph 4.2.2.2 must be repeated at interval of 500 
FC.

### Page 4

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 4 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
Accomplishment of MLG sliding tube overhaul in accordance with the applicable Component 
Maintenance Manual (CMM) cancels this repetitive GVI requested per paragraph 4.2.2.2.
4.1.2 MANPOWER
The estimated time to perform the GVI of LH and RH MLG sliding tubes (as per paragraph 4.2.2) is 2 
manhours.
4.2 DESCRIPTION
4.2.1 ACCESS
As per AMM chapter “Introduction – Aircraft status for maintenance” in manual front matter section, the 
following items shall be considered as the basic A/C configuration, before starting a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety locks and the wheel chocks are in 
position on the landing gear).
- Engine shut down, thrust reversers closed and locked.
- Aircraft in clean configuration.
- Parking brake applied.
- Aircraft electrical network de-energized.
- Hydraulic systems depressurized.
- Access to the cockpit and cabin is available.
- All circuit breakers are in closed position. 
- All controls in NORM, AUTO or OFF position.
This GVI does not require the removal of any component from the MLG (placard, jacking dome, wheels). 
Furthermore, no aircraft and no wheel jacking are necessary to perform this GVI.
4.2.2 INSPECTION REQUIREMENTS (RC)
4.2.2.1 Do a check of the LH/RH MLG sliding tubes PN and SN, and a check of the LH/RH 
MLG leg and dressings PN and SN
Do a check of the Landing Gear records or physical check to determine if the LH (Left Hand) and RH 
(Right Hand) MLG sliding tubes PN and SN are listed in Appendix 1 and if the LH and RH MLG leg and 
dressings PN and SN are listed in Appendix 2. 
If the MLG sliding tubes are not listed in Appendix 1 and the MLG leg and dressings are not listed in 
Appendix 2, no further action is required.
If the MLG sliding tubes listed in Appendix 1 and the MLG sliding tubes fitted on MLG leg and dressings 
listed in Appendix 2, have been overhauled after the 1 st of January 2015, then no further action is 
required.
If the MLG sliding tubes are listed in Appendix 1 or the MLG sliding tubes fitted on MLG leg and 
dressings are listed in Appendix 2, and have not been overhauled after the 1 st of January 2015, then 
do the GVI as per paragraph 4.2.2.2., and repeat this inspection at interval not exceeding 500 FC.

### Page 5

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 5 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.2.2 Do a GVI of the LH and RH MLG Sliding Tubes.
PREPARATION
(a) Make sure that the aircraft is electrically grounded, as per Ref. 7.
(b) Put a warning notice on panel 400VU to tell persons not to operate the landing gear controls.
Note: This GVI does not require the removal of placard and jacking dome in the area.
PROCEDURE
(a) Clean the external surface area around the MLG jacking dome, refer to Ref. 8.
(b) Do a GVI of the area around the jacking dome for cracks, refer to Figure 2.
Figure 2: Area of Inspection.
If cracks are found:
(1) Replace the cracked MLG Sliding Tube before the next flight as per Ref.9 and Ref.10.
(2) Contact AIRBUS immediately.
(3) Put the removed parts in quarantine pending Airbus instructions.

### Page 6

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 6 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
(c) Appendix 3 Inspection Reporting sheet shall be filled and returned to Airbus even if nil findings.
CLOSE-UP
(a) Make sure that the work areas are clean and clear of tools and other items of equipment.
(b) Remove the warning notice.
(c) Put the aircraft back to its initial configuration.
4.2.3 FINDINGS (RC)
In case of crack found during the GVI, the MLG sliding tube has to be replaced before next flight, refer 
to Ref.9 and Ref.10.
Report findings immediately to Airbus and put the removed parts in quarantine pending Airbus 
instructions.
4.3 SPARES AND TOOLING
No specific tooling is required to perform this GVI.
5. FURTHER INFORMATION
5.1 FOLLOW-UP PLAN
It is anticipated that an Airworthiness Directive will be issued by EASA to mandate the content of this
AOT.
5.2 IMPACTED DOCUMENTATION
N/A
6. AOT APPROVAL
The technical content of this document is approved under the authority of the DOA ref.EASA.21J.031.
7. REPORTING
Questions about this AOT are to be addressed to Airbus Customer Services through TechRequest on 
Airbus World, selecting Engineering Domain, Engineering Support Section and ATA 32-11.
As per latest reporting policy (Ref to OIT 999.0018/16), inspection results (with or without findings) are to 
be addressed to Airbus Customer Services through the generic e-mail address:  
inspection.results@airbus.com.
Best Regards,
Christian FREMONT
VICE PRESIDENT ENGINEERING SUPPORT
CUSTOMER SERVICES
Jean-Pierre GOMEZ
VICE PRESIDENT A320 PROGRAMME
CUSTOMER SERVICES

### Page 7

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 7 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 1
List of suspected MLG sliding tubes SN
Aircraft type MLG sliding tubes Part Number MLG sliding tubes Serial Number
76B
1012B
1244B
1286B
1299B
1362B
1522B
1549B
1568B
MAL1086
MAL1141
MAL1313
MAL1323
MAL1391
MAL1423
MAL1439
201160302 
(CMM 32-11-33)
SS4041
201371302 
(CMM 32-11-33) 1366B
06MDM00112
06MDM00135
07B4281X15128
07B4380X15217
07B4580X8929
B1885058
B1975084
B4652242
B136-1986
B148-1944
B157-5034
B192-5102
B194-5061
B203-5085
B224-2065
B226-2057
B230-2104
A318/A319/A320
201371304 
(CMM 32-11-33; 32-12-25)
B232-2071

### Page 8

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 8 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
B237-2072
B254-5183
B254-5294
B255-5175
B287-5181
B288-5165
B320-2173
B343-5134
B394-2208
B399-2202
B403-5224
B408-5246
B438-5113
B444-5189
B464-2243
B490-5307
B492-5313
B505-2257
B508-2260
B533-5272
B578-5273
B585-5322
B594-5347
B622-2338
B637-2272
B678-2381
B686-2355
B687-2351
B777-2438
B779-2440
B794-5410
B832-2500
B835-2499
B891-2533
B903-2516
B939-5445
B972-2620
B988-2601
B995-5468
B999-5469 
201371304
(CMM 32-11-33; 32-12-25)
B1013-2665

### Page 9

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 9 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
B1041-5461
B1052-2670
B1054-2672
B1059-2677
B1086-5495
B1171-5514
B1176-5474
B1177-2739
B1234-2769
B1237-2772
B1278-2681
B1283-2846
B1299-2825
B1380-2884
B1383-2871
B1404-2927
B1488-3012
B1543-2965
B1564-5677
B1570-2995
B1577-5717
B1581-5708
B1586-5697
B1587-5698
B1591-5703
B1649-3050
B1662-3072
B1664-3076
B1673-5742
B1723-3108
B1726-3111
B1816-5776
B1874-3186
B1875-3187
B1920-3218
B1926-3199
B1947-3231
B1948-8082
B1981-3175
B2006-3261
201371304
(CMM 32-11-33; 32-12-25)
B2008-3263

### Page 10

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 10 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
B2110-5764
B2126-8133
B2147-8111
B2191-3410
B2218-3431
B2234-3438
B2239-3443
B2274-3472
B2282-3506
B2400-3598
B2401-3599
B2403-3601
B2451-3610
B2455-3633
B2458-3611
B2460-3613
B2477-3650
B2514-3656
B2602-3726
B2603-3727
B3372-14410
B3399-14462
MDMDDD0014M
MDMDDD0034M
201371304
(CMM 32-11-33; 32-12-25)
MDMDDD0111M
B0282-511
B0289-518
B0293-522
B0298-536
B0373-0606
B0378-623
B0440-689
B0477-726
B0482-740
A321
201522353
(CMM 32-12-22; 32-12-12)
B0489-734

### Page 11

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 11 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 2
List of suspected MLG leg and dressings SN
MLG leg and dressing MLG leg and dressingAircraft type side
Part number Serial number
LH 201376001-XXX(CMM 32-11-32) DRG1979/91
RH 201376002-XXX(CMM 32-11-32) DRG9413/90
M-DG-0422
MDG-0988
M-DG-1604
M-DG-2439
M-DG-2611
LH
201582001-XXX
(CMM 32-12-24)
MDG3296
M-DG-0425
MDG-0992
M-DG-1605
M-DG-2440
A318/A319/A320
RH
201582002-XXX
(CMM 32-12-24)
M-DG-2612
M-DG-0326LH 201585003-XXX(CMM 32-12-21) M-DG-0416
M-DG-0327A321 RH 201585004-XXX(CMM 32-12-21) M-DG-0417

### Page 12

ALERT OPERATORS TRANSMISSION - AOT 
AOT ref: A32N023-21 Rev 00 Page 12 of 12 Date: 05-MAY-2021
© AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
APPENDIX 3
INSPECTION REPORTING SHEET
DATE OF INSPECTION  
PN SN CSN CSOMLG Sliding tube     
Fitted on A/C MSN  
QUESTION
YES
 
NO 
ARE CRACKS FOUND ON 
SURFACE AROUND THE 
JACKING DOME?
PN: Part Number.
SN: Serial Number.
CSN: Cycle Since New.
CSO: Cycle Since Overhaul.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
