# Airbus Service Bulletin A340-25-4349

Copy: Revision 02 ("A340-25-4349 R02"), 114 pages: PDF https://openairdocs.org/files/sha256/9b/4f/9b4f687b18f7b5d58010ef6a4fb52b1eea6046283a4eefb7ae1381a02743aa65; text https://openairdocs.org/service-documents/airbus/a340-25-4349/file/9b4f687b18f7.md. Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2015-3631; AD 2016-25-31 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Airbus](https://openairdocs.org/service-documents/airbus.md)
- Type: Service bulletin (Service Bulletin)
- Number: A340-25-4349
- Latest revision known: A340-25-4349, Revision 02, dated September 4, 2015 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/airbus/a340-25-4349

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-25-31](https://openairdocs.org/ad/2016-25-31.md), effective Feb 7, 2017: Revisions 01 and 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/airbus/a340-25-4349/proposed.md).

## Text (114 pages)

Rights: © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2015-3631; AD 2016-25-31 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

@A340
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - CURTAINS AND PARTITIONS -
INTRODUCE MODIFIED ELECTRICAL BONDING OF COCKPIT DOOR.
MODIFICATION No.: 203228D50684 204312D50883
This page transmits Revision No.02 of Service Bulletin No.A340-25-4349
ADDITIONAL WORK
**CONF ALL
No additional work is required by this revision for aircraft modified by any previous issue.
REASON
Revision No. 02 issued to:
- update the illustration to correct the bonding hole location
- add a note in illustration to indicate Typical Installation
- update steps in Job Set-up to remove the parts as necessary from the coat stowage
- add a note in concurrent requirement
- add a note in Procedure to adapt bonding lead length
- add step in Test procedure to test the operation and correct close of cockpit door
- update steps in Close-up to install the removed parts from the coat stowage.
CHANGES
SUMMARY
EFFECTIVITY
 OPERATOR LIST UPDATED
 R
CONCURRENT REQUIREMENTS
 CONCURRENT REQUIREMENTS UPDATED
 R
REFERENCES / REPERCUSSIONS
 REFERENCES/REPERCUSSIONS TABLE
UPDATED
R
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 2

@A340
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
PLANNING INFORMATION
EFFECTIVITY
 EFFECTIVITY RELATED INFORMATION
UPDATED
R
Configuration definition
CONF 001
 CONFIGURATION DEFINITION UPDATED
 R
CONCURRENT REQUIREMENTS
 CONCURRENT SB LIST UPDATED
 R
REFERENCES
 REFERENCED DOCUMENTATION UPDATED
 R
MATERIAL INFORMATION
MATERIAL - PRICE AND AVAILABILITY
Procurement Addresses
 PROCUREMENT ADDRESSES UPDATED
 R
INDUSTRY SUPPORT INFORMATION
 INDUSTRY SUPPORT INFORMATION UPDATED
 R
LIST OF MATERIALS - OPERATOR
SUPPLIED
Components
Component COMPD02
 PART MATERIAL SET UPDATED
QUANTITY UPDATED
R
ACCOMPLISHMENT INSTRUCTIONS
TASK 254349- 831-848-001-Modification
Subtask 254349-941-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Subtask 254349-941-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Subtask 254349-941-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Subtask 254349-831-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
PART NUMBER UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
REFERENCES UPDATED
R
Subtask 254349-831-202-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
NOTE UPDATED
REFERENCES UPDATED
R
Subtask 254349-831-201-002
 SUBTASK SOLUTION UPDATED
CONFIGURATION UPDATED
PART NUMBER UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
R
Subtask 254349-831-202-002
 SUBTASK SOLUTION UPDATED
NOTE UPDATED
R
Subtask 254349-831-201-004
 SUBTASK SOLUTION UPDATED
CONFIGURATION UPDATED
PART NUMBER UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
R
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 2
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 3

@A340
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
Subtask 254349-831-202-004
 SUBTASK SOLUTION UPDATED
NOTE UPDATED
R
Subtask 254349-760-201-001
 SUBTASK SOLUTION UPDATED
 R
Subtask 254349-760-201-001
 SUBTASK SOLUTION UPDATED
 R
Subtask 254349-942-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Subtask 254349-942-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Subtask 254349-942-201-001
 SUBTASK SOLUTION UPDATED
REFERENCED DOCUMENTATION UPDATED
R
Fig. A-GBCAA
Fig. A-GBCAA Sheet 02
 SHEET UPDATED
 R
Fig. A-GBCAA Sheet 03
 SHEET UPDATED
 R
Fig. A-GBCAB
Fig. A-GBCAB Sheet 02
 SHEET UPDATED
 R
Fig. A-GBCAB Sheet 03
 SHEET UPDATED
 R
FILLING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
HISTORY OF PREVIOUS REVISIONS
Revision No. 01 issued to:
update the reason paragraph to remove reference to the In-Flight Entertainment (IFE) wiring
delete MSN 0048 and 0088 from the effectivity
update of Concurrent Requirement to add Service Bulletin No. A340-25-4217
update the kits and associated accomplishment instructions.
REVISION SEQUENCE
ORIGINAL: May 28/14
REVISION No. : 01 - Oct 27/14
REVISION No. : 02 - Sep 04/15
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 3
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 4

@A340
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
This Page Intentionally Left Blank
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 4
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 5

@A340
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
This summary is for information only and is not approved for modification of the aircraft.
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - CURTAINS AND PARTITIONS -
INTRODUCE MODIFIED ELECTRICAL BONDING OF COCKPIT DOOR.
**CONF ALL
MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR
 None
MINOR
 203228D50684
 204312D50883
NOTE
: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Airbus has identified a potential risk of electrical shocks in case of chafing at the cockpit door. The
electrical bonding of the cockpit door has to be improved in order to mitigate this potential risk.
This Service Bulletin details the work necessary to improve the electrical bonding.
Accomplishment of this Service Bulletin improves the effectiveness of the electrical bonding thus will
contribute to prevent the risk of an electrical shock.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE
 MANDATORY (1)
 CANCELS INSPECTION SB
 NO
POTENTIAL AD
 YES
 A/C OPERATION AFFECTED
 NO
RELIABILITY AFFECTED
 NO
 PAX COMFORT AFFECTED
 NO
COST SAVING
 NO
 LROPS AFFECTED
 NO
STRUCTURAL LIFE EXTN
 NO
 VENDOR SB INVOLVED
 NO
NOTE
 (1)
: Service Bulletin must be accomplished.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 6

@A340
SERVICE BULLETIN
SUMMARY
MATERIAL PRICE INFORMATION
**CONF 001
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 254349D01R06
 1
 730.00
 Screw, Washer, Nut, Rivet, Bracket,
Bonding-Lead, Tube, Placard
Component COMPD01
 1
 See SB
 Bonding Lead, Washer, Screw
**CONF 002
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 254349D01R06
 1
 730.00
 Screw, Washer, Nut, Rivet, Bracket,
Bonding-Lead, Tube, Placard
Component COMPD01
 1
 See SB
 Bonding Lead, Washer, Screw
**CONF 003
MATERIAL PRICE INFORMATION TABLE
MATERIAL SET
 QTY PER
A/C
PRICE PER
A/C (USD)
MAIN PARTS
Kit 254349D02R02
 1
 735.00
 Screw, Washer, Nut, Rivet, Bracket,
Bonding-Lead, Tube, Placard
Component COMPD02
 1
 See SB
 Bonding Lead, Washer, Screw
EFFECTIVITY
**CONF ALL
This Service Bulletin is applicable to this (these) operator(s) :
06Y 15R 15T 22O
 31V 56W 74W 83V 98W
 98X ABD AFR AIB
ALD
 ALK ARG BOE CAL CCA CPA DGA DLH F2I FIN G8E GAF
HFM
 HFY IBE IRC IRM KAC LAN M3R MAU MDG O2X
 PAL PUE
QAF S3R SAA SAS SFB SLM SVW SWR TAP THT THY UAE VCV
XAX
CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the
following Service Bulletin:
Service Bulletin No. A340-25-4217
NOTE
: Service Bulletin No. A340-25-4217 (EQUIPMENT/FURNISHINGS - PAX
COMPARTMENT - MODIFY CDLS WIRING LOOM IN UPPER COCKPIT DOOR
PLATE COVER) which applies Modification No. 51911D44499.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 2
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 7

@A340
SERVICE BULLETIN
SUMMARY
NOTE
: Service Bulletin No. A340-25-4217 (EQUIPMENT/FURNISHINGS - PAX
COMPARTMENT - MODIFY CDLS WIRING LOOM IN UPPER COCKPIT DOOR
PLATE COVER) is valid for all aircraft in the effectivity of this Service Bulletin which
have not embodied Modification No. 52869D44765 or Modification No. 53292D44777.
REFERENCES / REPERCUSSIONS
TFU
 None
OEB
 None
AOT
 None
SIL
 None
ISI
 None
LINE MAINTENANCE AFFECTED
 No
LIFE LIMIT
 None
OTHER
 None
NATURE OF THE WORK
AIRCRAFT
 YES
EQUIPMENT
 NO
HARD
 NO
SOFT
 NO
OBRM
 NO
MANPOWER
**CONF 001
Task 254349-831-848-001: Modification
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
**CONF 002
Task 254349-831-848-001: Modification
TOTAL MANHOURS
 8.75
ELAPSED TIME (HOURS)
 8.75
**CONF 003
Task 254349-831-848-001: Modification
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
APPENDICES
**CONF ALL
None
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 3
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 8

@A340
SERVICE BULLETIN
SUMMARY
**CONF 001
FR11
FR16A
B
A
A
Z220
B
FR11
FR11A
F_SB_254349_6_SAAA_01_01
Figure A-GSAAA - Sheet 01
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 4
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 9

@A340
SERVICE BULLETIN
SUMMARY
**CONF 002
FR11
FR16A
B
A
A
Z220
B
FR11
FR11A
F_SB_254349_6_SAAB_01_01
Figure A-GSAAB - Sheet 01
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 5
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 10

@A340
SERVICE BULLETIN
SUMMARY
**CONF 003
FR11
FR16A
B
A
A
Z220
B
FR11
FR11A
F_SB_254349_6_SAAC_01_01
Figure A-GSAAC - Sheet 01
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 6
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 11

@A340
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
T e l:( 3 3 )56 19 33 33 3
Telex : AIRBU 530526F
F a x:( 3 3 )56 19 34 25 1
MANDATORY
 MANDATORY
 MANDATORY
ATA SYSTEM: 25
TITLE: EQUIPMENT/FURNISHINGS - CURTAINS AND PARTITIONS -
INTRODUCE MODIFIED ELECTRICAL BONDING OF COCKPIT DOOR.
MODIFICATION No.: 203228D50684 204312D50883
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
This modification is applicable by Service Bulletin only.
(1) Models
340-211 340-212 340-213 340-311 340-312 340-313
(2) Effectivity by MSN
0002 0004 0006 0009 0014 0020 0022-0023
 0025-0026
 0029 0031-0034
 0038 0041
0043-0044 0046-0047 0049 0051
 0056-0058 0061 0063 0074-0076 0078-0081
0084-0085 0089-0091 0093-0094 0101 0104 0114-0115 0117 0123 0125-0126 0128
0131 0134-0137 0139 0141-0142 0145-0147 0149-0152 0154 0156-0161 0163-0164
0166-0170 0173-0175
 0178-0180 0182 0185-0187 0190 0192-0194 0196-0197 0199
0201-0202 0204 0207-0208 0210 0212-0218 0220-0221 0227-0228 0233 0236-0237
0242-0243 0245-0246 0252 0257 0260 0263-0264 0268 0270 0273-0274 0278 0280
0282 0292 0297 0302 0304 0307 0310 0318-0319 0321 0325 0327 0329 0331-0332
0335 0347 0352 0354-0355 0359 0363 0367 0373-0374 0377-0379 0381 0385 0387
0390 0395 0399 0402 0406 0411 0413
 0415
 0424 0429-0430 0433-0435 0438 0442
0446-0447 0450 0459 0467 0470 0474 0483 0528 0538 0541 0544-0546 0554 0556
0559 0561-0562 0582 0585 0590 0598 0643 0646 0651 0668 0793 0800 0835 0844
0921 0938 0955
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 1
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 12

@A340
SERVICE BULLETIN
(3) Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
 MSN
06Y
 0139 0149
15R
 0151
15T
 0009
22O
 0257
31V
 0093
56W
 0006
74W
 0047 0051
83V
 0216 0280
 0292
98W
 0014
 0022
98X
 0429
ABD
 0210
AFR
 0029 0078 0084 0186 0207 0237 0245 0246 0260 0307 0310 0377
0399
AIB
 0131 0141 0161 0182 0192
 0199
ALD
 0156
 0159
 0178
ALK
 0032 0033 0034 0367 0374 0381
ARG
 0063
 0074
 0080
 0085 0094 0123 0126 0128 0170 0193 0373
BOE
 0554
CAL
 0402 0406 0411 0415 0433 0541
CCA
 0201 0242 0243 0264
CPA
 0136 0137 0142 0147 0157 0160 0208 0218 0220 0227 0228
DGA
 0075 0081
DLH
 0135 0158 0213 0233 0252 0297 0304 0321 0325 0327 0335 0347
0352 0354 0379 0390 0434 0447
F2I
 0038
 0043
 0114
 0214
FIN
 0058 0168 0174 0835 0844 0921 0938
G8E
 0173
 0187
 0196
GAF
 0274 0355
HFM
 0117
HFY
 0190
 0202
IBE
 0125 0134 0145 0146 0217 0221 0329 0483
IRC
 0002
IRM
 0020 0056 0164
 0282
KAC
 0089 0090 0101 0104
LAN
 0359 0363 0442
M3R
 0061
MAU
 0076 0152 0194 0268 0793 0800
MDG
 0319
O2X
 0273
PAL
 0302 0318 0332 0387 0459 0474
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 2
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 13

@A340
SERVICE BULLETIN
OPERATOR
 MSN
PUE
 0212 0215
QAF
 0026 0528
S3R
 0004 0204
SAA
 0197 0378 0544 0582 0590 0643 0646 0651
SAS
 0167 0413 0424 0430 0435 0450 0467 0470
SFB
 0046
SLM
 0049
SVW
 0955
SWR
 0150 0154 0169 0175 0179 0263 0538 0545 0546 0556 0559 0561
0562 0585 0598
TAP
 0041 0044 0079 0091
THT
 0385 0395 0438 0446 0668
THY
 0023 0025 0057 0115 0180 0270 0331
UAE
 0163 0166 0185 0236
VCV
 0031
XAX
 0278
(4) Configuration by MSN
MSN
 CONFIGURATION
0002 0006 0009 0014 0020 0022 0023 0025 0026 0029 0031
0032 0033 0034 0038 0041 0043 0044 0047 0049 0051 0056
0057 0058 0063 0074 0075 0076 0078 0079 0080 0081 0084
0085 0089 0090 0091 0093 0094 0101 0104 0114 0115 0117
0123 0125 0126 0128 0131 0134 0135 0136 0137 0139 0141
0142 0145 0146 0147 0149 0150 0152 0154 0156 0157 0158
0159 0160 0161 0163 0164 0166 0167 0168 0169 0170 0173
0174 0175 0178 0179 0180 0182 0185 0186 0187 0190 0192
0193 0194 0196 0197 0199 0201 0202 0207 0208 0210 0212
0213 0214 0215 0216 0217 0218 0220 0221 0227 0228 0233
0236 0237 0242 0243 0245 0246 0252 0257 0260 0263 0264
0268 0270 0273 0274 0278 0280 0282 0292 0297 0302 0304
0307 0310 0318 0319 0321 0325 0327 0329 0331 0332 0335
0347 0352 0354 0355 0359 0363 0367 0373 0374 0377 0379
0381 0385 0387 0390 0395 0399 0402 0406 0411 0413 0415
0424 0429 0430 0433 0434 0435 0438 0442 0446 0447 0450
0459 0467 0470 0474 0483 0528 0538 0541 0544 0545 0546
0554 0556 0559 0561 0562 0582 0585 0590 0598 0643 0646
0651 0668 0955
001
0004 0046 0061 0151 0204 0378
 001 003
0793 0800 0835 0844 0921 0938
 002
(5) Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft given in the effectivity of this Service Bulletin which
have installed the cockpit door via mod 50014D44099 and have installed a reinforced
partition structure via mod 50561S16638 or SB A340-25-4187 or SB A340-25-4205.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 3
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 14

@A340
SERVICE BULLETIN
**CONF 002
Config. 002 is valid for all the aircraft given in the effectivity of this Service Bulletin which
have installed a damping device to the cockpit door via mod 51720D44340 and have
installed a reinforced partition structure via mod 50561S16638.
**CONF 003
Config. 003 is valid for all the aircraft given in the effectivity of this Service Bulletin which
have installed the cockpit door via mod 50014D44099 and have not installed a
reinforced partition structure via mod 50561S16638 or SB A340-25-4187 or SB
A340-25-4205.
(6) Material Effectivity
**CONF 001
MATERIAL
 QTY PER A/C
 SEE NOTES
Kit 254349D01R06
 1
Component COMPD01
 1
 (1)
Consumable CMLD01
 1
NOTE
 (1)
: Operators with Kit 254349D01R04 will require COMPD01
**CONF 002
MATERIAL
 QTY PER A/C
 SEE NOTES
Kit 254349D01R06
 1
Component COMPD01
 1
 (1)
Consumable CMLD01
 1
NOTE
 (1)
: Operators with Kit 254349D01R04 will require COMPD01
**CONF 003
MATERIAL
 QTY PER A/C
 SEE NOTES
Kit 254349D02R02
 1
Component COMPD02
 1
 (1)
Consumable CMLD01
 1
NOTE
 (1)
: Operators with Kit 254349D02R01 will require COMPD02
**CONF ALL
B. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of
the following Service Bulletin:
Service Bulletin No. A340-25-4217
NOTE
: Service Bulletin No. A340-25-4217 (EQUIPMENT/FURNISHINGS - PAX
COMPARTMENT - MODIFY CDLS WIRING LOOM IN UPPER COCKPIT
DOOR PLATE COVER) which applies Modification No. 51911D44499.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 4
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 15

@A340
SERVICE BULLETIN
NOTE
: Service Bulletin No. A340-25-4217 (EQUIPMENT/FURNISHINGS - PAX
COMPARTMENT - MODIFY CDLS WIRING LOOM IN UPPER COCKPIT
DOOR PLATE COVER) is valid for all aircraft in the effectivity of this
Service Bulletin which have not embodied Modification No. 52869D44765 or
Modification No. 53292D44777.
C. REASON
(1) History
Airbus has identified a potential risk of electrical shocks in case of chafing at the cockpit
door. The electrical bonding of the cockpit door has to be improved in order to mitigate
this potential risk.
(2) Objective/Action
This Service Bulletin details the work necessary to improve the electrical bonding.
(3) Advantages
Accomplishment of this Service Bulletin improves the effectiveness of the electrical
bonding thus will contribute to prevent the risk of an electrical shock.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
**CONF 001
Task 254349-831-848-001: Modification
(1) Modify the Cockpit Door Frame Structure
(2) Install Bonding-Leads to the Upper Cockpit Door Frame
**CONF 002
Task 254349-831-848-001: Modification
(1) Modify the Cockpit Door Frame Structure
(2) Install Bonding-Leads to the Upper Cockpit Door Frame
**CONF 003
Task 254349-831-848-001: Modification
(1) Modify the Cockpit Door Frame Structure
(2) Install Bonding-Leads to the Upper Cockpit Door Frame
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 5
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 16

@A340
SERVICE BULLETIN
**CONF ALL
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
This Service Bulletin has been classified Mandatory. It is expected that an Airworthiness
Directive (AD) published by the European Av iation Safety Agenc y (EASA) will be issued
to confirm this classification. The accomplishment timescale, which has not yet been
defined, will be given in the AD.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
**CONF 001
Task 254349-831-848-001: Modification
Get Access
 1.00
On Aircraft
Modify the Cockpit Door Frame Structure
 3.50
Install Bonding-Leads to the Upper Cockpit Door
Frame
1.00
Tests
 0.50
Close-Up
 1.00
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
**CONF 002
Task 254349-831-848-001: Modification
Get Access
 1.00
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 6
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 17

@A340
SERVICE BULLETIN
Task 254349-831-848-001: Modification
On Aircraft
Modify the Cockpit Door Frame Structure
 3.75
Install Bonding-Leads to the Upper Cockpit Door
Frame
2.50
Tests
 0.50
Close-Up
 1.00
TOTAL MANHOURS
 8.75
ELAPSED TIME (HOURS)
 8.75
**CONF 003
Task 254349-831-848-001: Modification
Get Access
 1.00
On Aircraft
Modify the Cockpit Door Frame Structure
 3.50
Install Bonding-Leads to the Upper Cockpit Door
Frame
1.00
Tests
 0.50
Close-Up
 1.00
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
**CONF ALL
H. WEIGHT AND BALANCE
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer’s Empty Weight (MEW) and do not include operator’s items. For the definition of
MEW and operator’s items, refer to the Weight and Balance Manual (WBM) Chapter 1-00-07.
Manufacturers Empty Weight +0.13 KG (+0.2865 LB)
Effect on Balance +1.317 KGM (+9.525 LB.FT )
I. ELECTRICAL LOAD DATA
Not Changed
J. REFERENCES
**CONF 001
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
11-00-00 12-34-24 20-21-11
20-21-15 20-28-00 25-13-44
25-13-46 25-23-42 52-51-00
52-51-11
 52-51-15
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20 20-33-00 20-33-30
20-51-20 20-55-00
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 7
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 18

@A340
SERVICE BULLETIN
Illustrated Parts Catalog (IPC)
 52-51-01
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-42-00 51-43-00
51-44-00 51-75-12
Weight and Balance Manual (WBM)
 Chapter 1-00-07
**CONF 002
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
11-00-00 12-34-24 20-21-11
20-21-15 20-28-00 25-13-44
25-13-46 25-23-42 52-51-00
52-51-11 52-51-15
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20 20-33-00 20-33-30
20-51-20 20-55-00
Illustrated Parts Catalog (IPC)
 52-51-01
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-42-00 51-43-00
51-44-00 51-75-12
Weight and Balance Manual (WBM)
 Chapter 1-00-07
**CONF 003
Aircraft Maintenance Manual (AMM)
 06-20-00 06-31-53 06-41-53
11-00-00 12-34-24 20-21-11
20-21-15 20-28-00 25-13-44
25-13-46 25-23-42 52-51-00
52-51-11 52-51-15
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20 20-33-00 20-33-30
20-51-20 20-55-00
Illustrated Parts Catalog (IPC)
 52-51-01
Standards Manual (SM)
Structural Repair Manual (SRM)
 51-24-00 51-42-00 51-43-00
51-44-00 51-75-12
Weight and Balance Manual (WBM)
 Chapter 1-00-07
**CONF ALL
K. PUBLICATION AFFECTED
Aircraft Maintenance Manual (AMM)
 52-51-00 52-51-11
Illustrated Parts Catalog (IPC)
 25-81-01 52-51-01
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 8
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 19

@A340
SERVICE BULLETIN
2. MATERIAL INFORMATION
**CONF ALL
A. MATERIAL - PRICE AND AVAILABILITY
(1) Procurement Addresses
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Kit 254349D01R06
Kit 254349D02R02
AIRBUS Material, Logistics and Suppliers
ATP II B,
Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by E-mail: airbus.kit@airbus.com
Telephone Hotlines:
A330/A340. A300/310: +49 40 743 51616
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Component COMPD01
Component COMPD02
AIRBUS Material, Logistics and Suppliers
IFD - In Flight Desk
Weg beim Jaeger 150
D-22335 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by fax: +49 40 50 76 4012
For ordering by E-mail:
ifd.spares@airbus.com
(2) Price and Availability
This table shows the component kits COMP needed to update the kits already held in
your stock to the latest status.
KIT HELD BY OPERATOR
 COMP KIT REQUIRED
 LATEST STATUS OF KIT
254349D01R04
 COMPD01
 254349D01R06
254349D02R01
 COMPD02
 254349D02R02
Operator supplied standard hardware parts required to accomplish this Service Bulletin
are to be supplied from Operator‘s stock.
Kit 254349D01R06
Cost
 730.00 USD
Availability
 90 calendar days from receipt of order
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 9
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 20

@A340
SERVICE BULLETIN
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
Kit 254349D02R02
Cost
 735.00 USD
Availability
 90 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AirbusSpares portal or through a request for quotation to airbus.kit@airbus.com.
B. INDUSTRY SUPPORT INFORMATION
For aircraft under warranty at Jan 01/12, AIRBUS will credit the manhours indicated in this
Service Bulletin at the agreed in-house warranty labor rate for claims received not later than
90 days after completion of the last affected aircraft of your fleet and AIRBUS will provide the
kits and COMPD01 listed in paragraph 2.D at no charge for orders placed before Nov 30/16.
For the organisation of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.
AIRBUS CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
T e l :( 3 3 )56 71 90 62 2
E-mail: monitored.retrofit@airbus.com
F a x :( 3 3 )56 19 32 74 5
C. LIST OF COMPONENTS
Kit 254349D01R06
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
1
 NAS1102-3-8
 2
 SCREW
2
 NAS1102-08-10
 6
 SCREW
5
 NAS1096-3-12
 1
 SCREW
6
 NSA5320-10
 1
 WASHER
7
 ABS1577D54
 1
 BRACKET
8
 ABS0547D503
 2
 RIVET
9
 NAS1802-3-9
 2
 SCREW
10
 ABS0916B05
 0.6 (ME)
 TUBING
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 10
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 21

@A340
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
11
 E0090-10-125NN
 2
 LEAD
12
 NAS1802-3-7
 4
 SCREW
13
 NAS1149C0332R
 6
 WASHER
14
 F2529200920000
 2
 WASHER
15
 NAS1726C3P
 4
 NUT
16
 E0090-10-100NN
 1
 LEAD
18
 F2529200700200
 6
 PLACARD
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
Kit 254349D02R02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
1
 NAS1102-3-8
 2
 SCREW
2
 NAS1102-08-10
 6
 SCREW
5
 NAS1096-3-12
 1
 SCREW
6
 NSA5320-10
 1
 WASHER
7
 ABS1577D54
 1
 BRACKET
8
 ABS0547D503
 2
 RIVET
9
 NAS1802-3-9
 2
 SCREW
10
 ABS0916B05
 0.7 (ME)
 TUBING
11
 E0090-10-125NN
 1
 LEAD
12
 NAS1802-3-7
 4
 SCREW
13
 NAS1149C0332R
 6
 WASHER
14
 F2529200920000
 2
 WASHER
15
 NAS1726C3P
 4
 NUT
16
 E0090-10-100NN
 1
 LEAD
17
 E0090-10-200NN
 1
 LEAD
18
 F2529200700200
 6
 PLACARD
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 11
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 22

@A340
SERVICE BULLETIN
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO CML
MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease
 03FAB1
 As required
Varnish - Electrical Bonding
 04TMB2
 As required
Polysulfide Sealant
 06AAB1
 As required
Non Aqueous Cleaner-General
 08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
(2) Components
Component COMPD01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: Operators with Kit 254349D01R04 will require COMPD01
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
Component COMPD02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 ITEM
 OLD PART N˚
 INT
 SEE
NOTES
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.
NOTE
: Operators with Kit 254349D02R01 will require COMPD02
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 12
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 23

@A340
SERVICE BULLETIN
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
(3) Equipment
None
E. PARTS TO BE RE-IDENTIFIED BY OPERATOR
None
F. TOOLING
None
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 13
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 24

@A340
SERVICE BULLETIN
This Page Intentionally Left Blank
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 14
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 25

@A340
SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
Task 254349-831-848-001 - Modification
WARNING
: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION
: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE) . WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC; AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE
: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
"refer to" are used and the operator has a procedure accepted by the local
authority he belongs to, the accepted alternative procedure can be used. When the
words "in accordance with" are used then the given procedure must be followed.
NOTE
: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE
: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE
: This Service Bulletin is classified mandatory or expected to be classified mandatory
by an Airworthiness Directive (AD). The paragraphs 3.C. and 3.D. in these
accomplishment instructions are Required for Compliance (RC) and must be done
to comply with the AD. Other paragraphs are recommended and may be deviated
from, done as part of other actions or done with accepted methods different from
those given in the Service Bulletin, as long as the RC paragraphs can be done and
the aircraft can be put back into a serviceable condition.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 15
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 26

@A340
SERVICE BULLETIN
Task Associated Data
**CONF 001
Zone
220
Manpower
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
**CONF 002
Zone
220
Manpower
TOTAL MANHOURS
 8.75
ELAPSED TIME (HOURS)
 8.75
**CONF 003
Zone
220
Manpower
TOTAL MANHOURS
 7.00
ELAPSED TIME (HOURS)
 7.00
**CONF ALL
A. GENERAL
**CONF 001
(1) Subtask 254349-910-201-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-801
Task 20-21-15-912-801
20-28-00, Page Block 201
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20
20-33-00
20-33-30
20-51-20
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 16
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 27

@A340
SERVICE BULLETIN
References
Structural Repair Manual (SRM)
 51-24-00
51-42-00
51-43-00
51-44-00
51-75-12
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(e) For the specification of materials (Mat. No.) given in this Service Bulletin refer to
Consumable Materials List (CML).
(f) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(g) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-801.
(h) For the electrical bonding, refer to ESPM 20-51-20 and AMM 20-28-00, Page Block
201.
(i) For the drilling of rivet holes:
- Use a soft lead pencil and make marks to show the position of the rivet holes.
- Make sure that you have the correct edge clearance before you drill the
fastener holes.
- If not shown otherwise the tolerance for rivet holes is + 0.1 mm (+ 0.004 in.).
- Transfer-drill the existing holes with a pilot drill and a drill bush.
- Drill new fastener holes with a pilot drill of 2.5 mm (0.098 in.) diameter.
Increase the hole diameter to the correct size for the fastener which you must
install.
- Deburr the holes after you have drilled them.
(j) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(k) Remove and install fasteners in accordance with SRM 51-42-00.
(l) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 17
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 28

@A340
SERVICE BULLETIN
(o) For the identification of wire and wire harnesses, refer to ESPM 20-32-20.
(p) For the general installation of electr ical wire harnesses, re fer to ESPM 20-33-00.
(q) For the installation of the protectiv e electrical conduits, r efer to ESPM 20-33-30.
(r) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
(2) Subtask 254349-839-201-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in the
Service Bulletin.
**CONF 002
(1) Subtask 254349-910-201-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-801
Task 20-21-15-912-801
20-28-00, Page Block 201
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20
20-33-00
20-33-30
20-51-20
Structural Repair Manual (SRM)
 51-24-00
51-42-00
51-43-00
51-44-00
51-75-12
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(e) For the specification of materials (Mat. No.) given in this Service Bulletin refer to
Consumable Materials List (CML).
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 18
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 29

@A340
SERVICE BULLETIN
(f) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(g) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-801.
(h) For the electrical bonding, refer to ESPM 20-51-20 and AMM 20-28-00, Page Block
201.
(i) For the drilling of rivet holes:
- Use a soft lead pencil and make marks to show the position of the rivet holes.
- Make sure that you have the correct edge clearance before you drill the
fastener holes.
- If not shown otherwise the tolerance for rivet holes is + 0.1 mm (+ 0.004 in.).
- Transfer-drill the existing holes with a pilot drill and a drill bush.
- Drill new fastener holes with a pilot drill of 2.5 mm (0.098 in.) diameter.
Increase the hole diameter to the correct size for the fastener which you must
install.
- Deburr the holes after you have drilled them.
(j) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(k) Remove and install fasteners in accordance with SRM 51-42-00.
(l) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(o) For the identification of wire and wire harnesses, refer to ESPM 20-32-20.
(p) For the general installation of electr ical wire harnesses, re fer to ESPM 20-33-00.
(q) For the installation of the protectiv e electrical conduits, r efer to ESPM 20-33-30.
(r) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
(2) Subtask 254349-839-201-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in the
Service Bulletin.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 19
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 30

@A340
SERVICE BULLETIN
**CONF 003
(1) Subtask 254349-910-201-001 - Standard Practices
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-801
Task 20-21-15-912-801
20-28-00, Page Block 201
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM)
 20-32-20
20-33-00
20-33-30
20-51-20
Structural Repair Manual (SRM)
 51-24-00
51-42-00
51-43-00
51-44-00
51-75-12
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.
(e) For the specification of materials (Mat. No.) given in this Service Bulletin refer to
Consumable Materials List (CML).
(f) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-801.
(g) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-801.
(h) For the electrical bonding, refer to ESPM 20-51-20 and AMM 20-28-00, Page Block
201.
(i) For the drilling of rivet holes:
- Use a soft lead pencil and make marks to show the position of the rivet holes.
- Make sure that you have the correct edge clearance before you drill the
fastener holes.
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 20
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 31

@A340
SERVICE BULLETIN
- If not shown otherwise the tolerance for rivet holes is + 0.1 mm (+ 0.004 in.).
- Transfer-drill the existing holes with a pilot drill and a drill bush.
- Drill new fastener holes with a pilot drill of 2.5 mm (0.098 in.) diameter.
Increase the hole diameter to the correct size for the fastener which you must
install.
- Deburr the holes after you have drilled them.
(j) Obtain fastener hole diameters and drill data in accordance with SRM 51-44-00.
(k) Remove and install fasteners in accordance with SRM 51-42-00.
(l) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.
(m) Apply sealant in accordance with SRM 51-24-00.
(n) Renew the protective finish in accordance with SRM 51-75-12.
(o) For the identification of wire and wire harnesses, refer to ESPM 20-32-20.
(p) For the general installation of electr ical wire harnesses, re fer to ESPM 20-33-00.
(q) For the installation of the protectiv e electrical conduits, r efer to ESPM 20-33-30.
(r) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
(2) Subtask 254349-839-201-001 - Administrative
Manpower Resources
Skills
 NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in the
Service Bulletin.
**CONF ALL
B. PREPARATION
**CONF 001
(1) Subtask 254349-941-201-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 25-13-44-000-801
Task 25-13-46-000-801
Task 25-23-42-000-801
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 21
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 32

@A340
SERVICE BULLETIN
NOTE
: The following items shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic systems depressurized.
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Remove the ceiling panel 221AC, refer to AMM Task 25-23-42-000-801.
(c) Remove the ceiling panel 211LC and 211MC, refer to AMM Task
25-13-44-000-801.
(d) Based on aircraft configuration, if installed, remove the upper panel from the coat
stowage, refer to AMM Task 25-13-46-000-801.
(e) Based on aircraft configuration, if installed, remove the parts as necessary from the
coat stowage to get access to the work area, refer to AMM Task 25-13-46-000-801.
**CONF 002
(1) Subtask 254349-941-201-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 25-13-44-000-801
Task 25-13-46-000-801
Task 25-23-42-000-801
NOTE
: The following items shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 22
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 33

@A340
SERVICE BULLETIN
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic systems depressurized.
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Remove the ceiling panel 221AC, refer to AMM Task 25-23-42-000-801.
(c) Remove the ceiling panel 211LC and 211MC, refer to AMM Task
25-13-44-000-801.
(d) Based on aircraft configuration, if installed, remove the upper panel from the coat
stowage, refer to AMM Task 25-13-46-000-801.
(e) Based on aircraft configuration, if installed, remove the parts as necessary from the
coat stowage to get access to the work area, refer to AMM Task 25-13-46-000-801.
**CONF 003
(1) Subtask 254349-941-201-001 - Job Set-up
Manpower Resources
Skills
 NON SPECIFIC
References
Aircraft Maintenance Manual (AMM)
 Task 12-34-24-860-802
Task 25-13-44-000-801
Task 25-13-46-000-801
Task 25-23-42-000-801
NOTE
: The following items shall be considered as the basic Aircraft
configuration before you start a maintenance task:
- Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
- Engine shut down, thrust reversers closed and locked
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 23
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 34

@A340
SERVICE BULLETIN
- Aircraft in clean configuration
- Parking brake applied
- Aircraft electrical network de-energized
- Hydraulic systems depressurized.
- Access to the cockpit and cabin is available
- All circuit breakers are in closed position
- All controls in NORM, AUTO or OFF position.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-860-802.
(b) Remove the ceiling panel 221AC, refer to AMM Task 25-23-42-000-801.
(c) Remove the ceiling panel 211LC and 211MC, refer to AMM Task
25-13-44-000-801.
(d) Based on aircraft configuration, if installed, remove the upper panel from the coat
stowage, refer to AMM Task 25-13-46-000-801.
(e) Based on aircraft configuration, if installed, remove the parts as necessary from the
coat stowage to get access to the work area, refer to AMM Task 25-13-46-000-801.
**CONF ALL
C. PROCEDURE
**CONF 001
(1) Subtask 254349-831-201-001 - Modify the Cockpit Door Frame Structure
Work Zones and Access Panels
Zone
 Access/Work location
220
Manpower Resources
Manhours
 3.50
Minimum number of person
 1
Subtask elapsed time
 3.50
Skills
 AIRFRAME
Material necessary to do the job
Kit 254349D01R06
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 NAS1102-3-8
 2
 SCREW
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 24
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 35

@A340
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
2
 NAS1102-08-10
 6
 SCREW
5
 NAS1096-3-12
 1
 SCREW
6
 NSA5320-10
 1
 WASHER
7
 ABS1577D54
 1
 BRACKET
8
 ABS0547D503
 2
 RIVET
18
 F2529200700200
 6
 PLACARD
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease
 03FAB1
 As required
Varnish - Electrical Bonding
 04TMB2
 As required
Polysulfide Sealant
 06AAB1
 As required
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 52-51-00-710-803
Task 52-51-11-820-801
Task 52-51-15-000-801
Task 52-51-15-400-801
Illustrated Parts Catalog (IPC)
 52-51-01
Fig. A-GBAAA
Prepare the bonding points at the wire
protection
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBBAA
Install the bracket at the pelmet
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBCAA
Prepare the bonding points at the door
posts
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBEAA
Prepare the bonding points at the webs
Sheet 01
Sheet 02
Sheet 03
(a) Remove the keypad from the gap cover, refer to AMM Task 52-51-15-000-801.
(b) Loosen the nuts and carefully remove the wire harness from the wire protection as
shown on Fig. A-GBAAA Sheet 02
 ,V i e wC .
(c) Modify the wire protection as follows:
1
 Prepare the bonding point at the front side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAA Sheet
03
,V i e wD .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 25
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 36

@A340
SERVICE BULLETIN
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAA Sheet 03
 ,V i e wD .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAA Sheet 03
,V i e wD .
2
 Prepare the bonding point at the upper side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAA Sheet
03
,V i e wE .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAA Sheet 03
 ,V i e wE .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAA Sheet 03
,V i e wE .
3
 Clean the bonding points with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Apply to the bonding points a thin coat of:
Mineral Oil Base
Grease
03FAB1 As required
NOTE
: The application of the grease is only necessary if you can
not install the bonding leads (SUBTASK 254349-831-202 001
Install Bonding-Leads to the Upper Cockpit Door Frame ) in
the next 4 hours.
5
 Install as shown on Fig. A-GBAAA Sheet 02
 ,V i e wC :
1 Placard F2529200700200 Item 18
(d) Modify the door posts as follows:
1
 Prepare the bonding point at the LH door post:
a
 Remove as shown on Fig. A-GBCAA Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAA Sheet 02
 ,V i e wF .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 26
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 37

@A340
SERVICE BULLETIN
c
 Install as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
d
 Apply to the screw, item 1 as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
Varnish - Electrical
Bonding
04TMB2 As required
NOTE
: Bonding can be performed on other door post location
than shown in Fig. A-GBCAA Sheet 02
 if this lead to less
equipment removal. Bonding is to be performed at one
position with screw NAS1102-3-8 installed.
2
 Prepare the bonding points at the RH door post:
a
 Remove as shown on Fig. A-GBCAA Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAA Sheet 02
 ,V i e wF .
c
 Install as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
d
 Remove as shown on Fig. A-GBCAA Sheet 03
 ,V i e wG :
6 Screw Item (2) Discard
1 Gap Cover Item (3) Retain
1 Door Frame Panel Item (4) Retain
NOTE
: For the PN of the gap cover, item (3) and the door frame
panel, item (4), refer to IPC 52-51-01.
e
 Remove as shown on Fig. A-GBCAA Sheet 03
 ,V i e wH :
1 Screw Item (5) Discard
1 Washer Item (6) Discard
f
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the screw head diameter as
shown on Fig. A-GBCAA Sheet 03
 ,V i e wJ .
g
 Install as shown on Fig. A-GBCAA Sheet 03
 ,V i e wJ :
1 Screw NAS1096-3-12 Item 5
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 27
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 38

@A340
SERVICE BULLETIN
1 Washer NSA5320-10 Item 6
h
 Apply to the screws, item 1 and 5 as shown on Fig. A-GBCAA Sheet 02
 ,
View F and Fig. A-GBCAA Sheet 03
 ,V i e wJ :
Varnish - Electrical
Bonding
04TMB2 As required
i
 Install as shown on Fig. A-GBCAA Sheet 03
 ,V i e wG :
1 Gap Cover Item (3) Retained at
removal
1 Door Frame Panel Item (4) Retained at
removal
6 Screw NAS1102-08-10 Item 2
3
 Install as shown on Fig. A-GBCAA Sheet 02
 , View C and D:
2 Placard F2529200700200 Item 18
(e) Install the bracket as follows:
1
 Remove the surface protection from the contact area of the bracket, item 7 to
the pelmet as shown on Fig. A-GBBAA Sheet 02
 ,V i e wD .
2
 Use the bracket, item 7 as template and mark the position of the holes as
shown on Fig. A-GBBAA Sheet 03
 ,V i e wE .
3
CAUTION
: MAKE SURE THAT YOU DO NOT DRILL TO MORE THAN
A DEPTH OF 21 MM (0.83 IN.) TO AVOID DAMAGE TO
THE S_GLASS ON THE CABIN SIDE.
Drill pilot holes to a diameter of 2.5 mm (0.098 in.) and a depth of 21 mm-1
mm (0.83 in.-0.039 in.).
4
 Drill the pilot holes to the final diameter of 4.1 mm (0.16 in.) and a depth of 21
mm-1 mm (0.83 in.-0.039 in.) as shown on Fig. A-GBBAA Sheet 03
 , Section
A-A.
5
 Deburr the holes.
6
 Remove the surface protection around the rivet holes to a diameter
approximately 3 mm (0.12 in.) larger than the rivet head diameter as shown on
Fig. A-GBBAA Sheet 02
 ,V i e wD .
7
 Clean the modification area with:
Non Aqueous
Cleaner-General
08BAA9 As required
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 28
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 39

@A340
SERVICE BULLETIN
Textile-Lint Free
Cotton
14SBA1 As required
8
 Install as shown on Fig. A-GBBAA Sheet 02
 ,V i e wD :
1 Bracket ABS1577D54 Item 7
2 Rivet ABS0547D503 Item 8
9
 Apply to the rivets, item 8 and to the edges of the bracket, item 7 as shown on
Fig. A-GBBAA Sheet 03
 , Section A-A:
Polysulfide Sealant 06AAB1 As required
Varnish - Electrical
Bonding
04TMB2 As required
10
 Install as shown on Fig. A-GBBAA Sheet 02
 ,V i e wC :
1 Placard F2529200700200 Item 18
(f) Modify the webs as follows:
1
 Prepare the bonding points at the RH web:
a
 Mark the position of the bonding point as shown on Fig. A-GBEAA Sheet
02
,V i e wD .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 17 mm (0.7 in.) as
shown on Fig. A-GBEAA Sheet 02
 ,V i e wD .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBEAA Sheet 02
,V i e wD .
e
 Install as shown on Fig. A-GBEAA Sheet 02
 ,V i e wD :
1 Placard F2529200700200 Item 18
2
 Prepare the bonding points at the LH web:
a
 Mark the position of the bonding point as shown on Fig. A-GBEAA Sheet
03
,V i e wF .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 17 mm (0.7 in.) as
shown on Fig. A-GBEAA Sheet 03
 ,V i e wF .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBEAA Sheet 03
,V i e wF .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 29
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 40

@A340
SERVICE BULLETIN
e
 Install as shown on Fig. A-GBEAA Sheet 03
 ,V i e wF :
1 Placard F2529200700200 Item 18
3
 Clean the bonding points with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Apply to the bonding points a thin coat of:
Mineral Oil Base
Grease
03FAB1 As required
NOTE
: The application of the grease is only necessary if you can
not install the bonding leads (SUBTASK 254349-831-202 001
Install Bonding-Leads to the Upper Cockpit Door Frame ) in
the next 4 hours.
(g) Install the keypad to the gap cover, refer to AMM Task 52-51-15-400-801.
(h) Do the operational test of the cockpit door emergency access, refer to AMM Task
52-51-00-710-803.
(2) Subtask 254349-831-202-001 - Install Bondi ng-Leads to the Upper Cockpit Door
Frame
Work Zones and Access Panels
Zone
 Access/Work location
220
Manpower Resources
Manhours
 1.00
Minimum number of person
 1
Subtask elapsed time
 1.00
Skills
 AIRFRAME
Material necessary to do the job
Kit 254349D01R06
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
9
 NAS1802-3-9
 2
 SCREW
10
 ABS0916B05
 0.6
 TUBING
11
 E0090-10-125NN
 2
 LEAD
12
 NAS1802-3-7
 4
 SCREW
13
 NAS1149C0332R
 6
 WASHER
14
 F2529200920000
 2
 WASHER
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 30
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 41

@A340
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
15
 NAS1726C3P
 4
 NUT
16
 E0090-10-100NN
 1
 LEAD
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
Component COMPD01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: Operators with Kit 254349D01R04 will require COMPD01
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Varnish - Electrical Bonding
 04TMB2
 As required
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 52-51-11-820-801
Fig. A-GBDAA
Install the bonding-leads at the upper
door frame
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Sheet 05
Sheet 06
(a) Install the bonding-leads at the RH door post as follows:
1
 Remove as shown on Fig. A-GBDAA Sheet 03
 ,V i e wE :
1 Screw Item (1) Discard
2
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the diameter of the washer, item 14
as shown on Fig. A-GBDAA Sheet 03
 ,V i e wF .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 31
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 42

@A340
SERVICE BULLETIN
3
 Clean the bonding points at the wire protection and the door post with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Cut two pieces of tubing to a length of 0.11 m (4.33 in.) from:
0.6 Tubing ABS0916B05 Item 10
5
 Push the tubings, item 10 over the bonding-leads, item 11 and shrink them.
6
 Install at the door post as shown on Fig. A-GBDAA Sheet 03
 ,V i e wF :
2 Bonding-Lead E0090-10-125NN Item 11
1 Screw NAS1802-3-9 Item 9
1 Washer NAS1149C0332R Item 13
1 Washer F2529200920000 Item 14
NOTE
: The bonding lead length may be adapted by using next longer
bonding lead length if necessary.
7
 Attach the bonding-lead, item 11 to the wire protection as shown on Fig. A-
GBDAA Sheet 03
, View F with:
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
8
 Clean the bonding point at the web with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
9
 Attach the bonding-lead, item 11 to the web as shown on Fig. A-GBDAA
Sheet 05
,V i e wJw i t h :
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 32
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 43

@A340
SERVICE BULLETIN
10
 Apply to the Screw, item 12 and the nut, item 15 as shown on Fig. A-GBDAA
Sheet 05
,V i e wJ :
Varnish - Electrical
Bonding
04TMB2 As required
11
 Apply to the Screws, item 9 and 12 and the nut, item 15 as shown on Fig. A-
GBDAA Sheet 03
,V i e wF :
Varnish - Electrical
Bonding
04TMB2 As required
(b) Install the bonding-leads at the LH door post as follows:
1
 Remove as shown on Fig. A-GBDAA Sheet 04
 ,V i e wG :
1 Screw Item (1) Discard
2
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the diameter of the washer, item 14
as shown on Fig. A-GBDAA Sheet 04
 ,V i e wH .
3
 Make sure that there is no surface protection at the bonding point from the
bracket.
4
 Clean the bonding points at the wire protection, the bracket and the door post
with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
5
 Cut two pieces of tubing to a length of 0.085 m (3.35 in.) and one piece to a
length of 0.185 m (7.28 in.) from:
0.6 Tubing ABS0916B05 Item 10
6
 Push the tubings, item 10 over the bonding-leads, item 16, 21 and 22 and
shrink them.
7
 Install at the door post as shown on Fig. A-GBDAA Sheet 04
 ,V i e wH :
1 Bonding Lead E0090-10-100NN Item 16
1 Bonding Lead E0090-18-200NN Item 22
1 Screw NAS1802-3-9 Item 9
1 Washer NAS1149C0332R Item 13
1 Washer F2529200920000 Item 14
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 33
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 44

@A340
SERVICE BULLETIN
For operators with KITD01R04 get this item from COMPD01:
1 Bonding Lead E0090-18-200NN Item 22
NOTE
: The bonding lead length may be adapted by using next longer
bonding lead length if necessary.
8
 Attach the bonding-lead, item 22, to the bracket as shown on Fig. A-GBDAA
Sheet 04
,V i e wHw i t h :
1 Bonding Lead E0090-18-100NN Item 21
1 Screw NAS1802-08-7 Item 19
1 Washer NAS1149CN832R Item 20
For operators with KITD01R04 get these items from COMPD01:
1 Bonding Lead E0090-18-100NN Item 21
1 Screw NAS1802-08-7 Item 19
1 Washer NAS1149CN832R Item 20
9
 Attach the bonding-lead, item 21, to the wire protection as shown on Fig. A-
GBDAA Sheet 04
, View H with:
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
10
 Clean the bonding point at the web with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
11
 Attach the bonding-lead, item 16, to the web as shown on Fig. A-GBDAA
Sheet 05
,V i e wKw i t h :
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 34
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 45

@A340
SERVICE BULLETIN
12
 Apply to the Screw, item 12 and the nut, item 15 as shown on Fig. A-GBDAA
Sheet 05
,V i e wK :
Varnish - Electrical
Bonding
04TMB2 As required
13
 Apply to the Screws, item 9 and 12 and the nut, item 15 as shown on Fig. A-
GBDAA Sheet 04
,V i e wH :
Varnish - Electrical
Bonding
04TMB2 As required
(c) Install the wire harness to the wire protection as shown on Fig. A-GBDAA Sheet
06
,V i e wL .
(d) Make sure that cockpit door operates easily and closes correctly, refer to AMM
Task 52-51-11-820-801.
**CONF 002
(1) Subtask 254349-831-201-002 - Modify the Cockpit Door Frame Structure
Work Zones and Access Panels
Zone
 Access/Work location
220
Manpower Resources
Manhours
 3.75
Minimum number of person
 1
Subtask elapsed time
 3.75
Skills
 AIRFRAME
Material necessary to do the job
Kit 254349D01R06
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 NAS1102-3-8
 2
 SCREW
2
 NAS1102-08-10
 6
 SCREW
5
 NAS1096-3-12
 1
 SCREW
6
 NSA5320-10
 1
 WASHER
7
 ABS1577D54
 1
 BRACKET
8
 ABS0547D503
 2
 RIVET
18
 F2529200700200
 6
 PLACARD
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease
 03FAB1
 As required
Varnish - Electrical Bonding
 04TMB2
 As required
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 35
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 46

@A340
SERVICE BULLETIN
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Polysulfide Sealant
 06AAB1
 As required
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 52-51-00-710-803
Task 52-51-11-000-802
Task 52-51-15-000-801
Task 52-51-15-400-801
Illustrated Parts Catalog (IPC)
 52-51-01
Fig. A-GBAAB
Prepare the bonding points at the wire
protection
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBBAB
Install the bracket at the pelmet
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBCAB
Prepare the bonding points at the door
posts
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBEAA
Prepare the bonding points at the webs
Sheet 01
Sheet 02
Sheet 03
(a) Remove the damper unit from the pelmet, refer to AMM Task 52-51-11-000-802.
(b) Remove the keypad from the gap cover, refer to AMM Task 52-51-15-000-801.
(c) Loosen the nuts and carefully remove the wire harness from the wire protection as
shown on Fig. A-GBAAB Sheet 02
 ,V i e wC .
(d) Modify the wire protection as follows:
1
 Prepare the bonding point at the front side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAB Sheet
03
,V i e wD .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAB Sheet 03
 ,V i e wD .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAB Sheet 03
,V i e wD .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 36
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 47

@A340
SERVICE BULLETIN
2
 Prepare the bonding point at the upper side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAB Sheet
03
,V i e wE .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAB Sheet 03
 ,V i e wE .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAB Sheet 03
,V i e wE .
3
 Clean the bonding points with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Apply to the bonding points a thin coat of:
Mineral Oil Base
Grease
03FAB1 As required
NOTE
: The application of the grease is only necessary if you can
not install the bonding leads (SUBTASK 254349-831-202 002
Install Bonding-Leads to the Upper Cockpit Door Frame ) in
the next 4 hours.
5
 Install as shown on Fig. A-GBAAB Sheet 02
 ,V i e wC :
1 Placard F2529200700200 Item 18
(e) Modify the door posts as follows:
1
 Prepare the bonding point at the LH door post:
a
 Remove as shown on Fig. A-GBCAB Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAB Sheet 02
 ,V i e wF .
c
 Install as shown on Fig. A-GBCAB Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 37
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 48

@A340
SERVICE BULLETIN
d
 Apply to the screw, item 1 as shown on Fig. A-GBCAB Sheet 02
 ,V i e wF :
Varnish - Electrical
Bonding
04TMB2 As required
NOTE
: Bonding can be performed on other door post location
than shown in Fig. A-GBCAB Sheet 02
 if this lead to less
equipment removal. Bonding is to be performed at one
position with screw NAS1102-3-8 installed.
2
 Prepare the bonding points at the RH door post:
a
 Remove as shown on Fig. A-GBCAB Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAB Sheet 02
 ,V i e wF .
c
 Install as shown on Fig. A-GBCAB Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
d
 Remove as shown on Fig. A-GBCAB Sheet 03
 ,V i e wG :
6 Screw Item (2) Discard
1 Gap Cover Item (3) Retain
1 Door Frame Panel Item (4) Retain
NOTE
: For the PN of the gap cover, item (3) and the door frame
panel, item (4), refer to IPC 52-51-01.
e
 Remove as shown on Fig. A-GBCAB Sheet 03
 ,V i e wH :
1 Screw Item (5) Discard
1 Washer Item (6) Discard
f
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the screw head diameter as
shown on Fig. A-GBCAB Sheet 03
 ,V i e wJ .
g
 Install as shown on Fig. A-GBCAB Sheet 03
 ,V i e wJ :
1 Screw NAS1096-3-12 Item 5
1 Washer NSA5320-10 Item 6
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 38
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 49

@A340
SERVICE BULLETIN
h
 Apply to the screws, item 1 and 5 as shown on Fig. A-GBCAB Sheet 02
 ,
View F and Fig. A-GBCAB Sheet 03
 ,V i e wJ :
Varnish - Electrical
Bonding
04TMB2 As required
i
 Install as shown on Fig. A-GBCAB Sheet 03
 ,V i e wG :
1 Gap Cover Item (3) Retained at
removal
1 Door Frame Panel Item (4) Retained at
removal
6 Screw NAS1102-08-10 Item 2
3
 Install as shown on Fig. A-GBCAB Sheet 02
 , View C and D:
2 Placard F2529200700200 Item 18
(f) Install the bracket as follows:
1
 Remove the surface protection from the contact area of the bracket, item 7 to
the pelmet as shown on Fig. A-GBBAB Sheet 02
 ,V i e wD .
2
 Use the bracket, item 7 as template and mark the position of the holes as
shown on Fig. A-GBBAB Sheet 03
 ,V i e wE .
3
CAUTION
: MAKE SURE THAT YOU DO NOT DRILL TO MORE THAN
A DEPTH OF 21 MM (0.83 IN.) TO AVOID DAMAGE TO
THE S_GLASS ON THE CABIN SIDE.
Drill pilot holes to a diameter of 2.5 mm (0.098 in.) and a depth of 21 mm-1
mm (0.83 in.-0.039 in.).
4
 Drill the pilot holes to the final diameter of 4.1 mm (0.16 in.) and a depth of 21
mm-1 mm (0.83 in.-0.039 in.) as shown on Fig. A-GBBAB Sheet 03
 , Section
A-A.
5
 Deburr the holes.
6
 Remove the surface protection around the rivet holes to a diameter
approximately 3 mm (0.12 in.) larger than the rivet head diameter as shown on
Fig. A-GBBAB Sheet 02
 ,V i e wD .
7
 Clean the modification areas with:
Non Aqueous
Cleaner-General
08BAA9 As required
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 39
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 50

@A340
SERVICE BULLETIN
Textile-Lint Free
Cotton
14SBA1 As required
8
 Install as shown on Fig. A-GBBAB Sheet 02
 ,V i e wD :
1 Bracket ABS1577D54 Item 7
2 Rivet ABS0547D503 Item 8
9
 Apply to the rivets, item 8 and to the edges of the bracket, item 7 as shown on
Fig. A-GBBAB Sheet 03
 , Section A-A:
Polysulfide Sealant 06AAB1 As required
Varnish - Electrical
Bonding
04TMB2 As required
10
 Install as shown on Fig. A-GBBAB Sheet 02
 ,V i e wC :
1 Placard F2529200700200 Item 18
(g) Modify the webs as follows:
1
 Prepare the bonding points at the RH web:
a
 Mark the position of the bonding point as shown on Fig. A-GBEAA Sheet
02
,V i e wD .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 17 mm (0.7 in.) as
shown on Fig. A-GBEAA Sheet 02
 ,V i e wD .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBEAA Sheet 02
,V i e wD .
e
 Install as shown on Fig. A-GBEAA Sheet 02
 ,V i e wD :
1 Placard F2529200700200 Item 18
2
 Prepare the bonding points at the LH web:
a
 Mark the position of the bonding point as shown on Fig. A-GBEAA Sheet
03
,V i e wF .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 17 mm (0.7 in.) as
shown on Fig. A-GBEAA Sheet 03
 ,V i e wF .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBEAA Sheet 03
,V i e wF .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 40
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 51

@A340
SERVICE BULLETIN
e
 Install as shown on Fig. A-GBEAA Sheet 03
 ,V i e wF :
1 Placard F2529200700200 Item 18
3
 Clean the bonding points with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Apply to the bonding points a thin coat of:
Mineral Oil Base
Grease
03FAB1 As required
NOTE
: The application of the grease is only necessary if you can
not install the bonding leads (SUBTASK 254349-831-202 002
Install Bonding-Leads to the Upper Cockpit Door Frame ) in
the next 4 hours.
(h) Install the keypad to the gap cover, refer to AMM Task 52-51-15-400-801.
(i) Do the operational test of the cockpit door emergency access, refer to AMM Task
52-51-00-710-803.
(2) Subtask 254349-831-202-002 - Install Bondi ng-Leads to the Upper Cockpit Door
Frame
Work Zones and Access Panels
Zone
 Access/Work location
220
Manpower Resources
Manhours
 2.50
Minimum number of person
 1
Subtask elapsed time
 2.50
Skills
 AIRFRAME
Material necessary to do the job
Kit 254349D01R06
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
9
 NAS1802-3-9
 2
 SCREW
10
 ABS0916B05
 0.6
 TUBING
11
 E0090-10-125NN
 2
 LEAD
12
 NAS1802-3-7
 4
 SCREW
13
 NAS1149C0332R
 6
 WASHER
14
 F2529200920000
 2
 WASHER
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 41
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 52

@A340
SERVICE BULLETIN
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
15
 NAS1726C3P
 4
 NUT
16
 E0090-10-100NN
 1
 LEAD
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
Component COMPD01
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
19
 NAS1802-08-7
 1
 SCREW
20
 NAS1149CN832R
 1
 WASHER
21
 E0090-18-100NN
 1
 LEAD
22
 E0090-18-200NN
 1
 LEAD
NOTE
: Operators with Kit 254349D01R04 will require COMPD01
NOTE
: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Varnish - Electrical Bonding
 04TMB2
 As required
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 52-51-11-400-802
Task 52-51-11-820-801
Fig. A-GBDAB
Install the bonding-leads at the upper
door frame
Sheet 01
Sheet 02
Sheet 03
Sheet 04
Sheet 05
Sheet 06
(a) Install the bonding-leads at the RH door post as follows:
1
 Remove as shown on Fig. A-GBDAB Sheet 03
 ,V i e wE :
1 Screw Item (1) Discard
2
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the diameter of the washer, item 14
as shown on Fig. A-GBDAB Sheet 03
 ,V i e wF .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 42
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 53

@A340
SERVICE BULLETIN
3
 Clean the bonding points at the wire protection and the door post with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Cut two pieces of tubing to a length of 0.11 m (4.33 in.) from:
0.6 Tubing ABS0916B05 Item 10
5
 Push the tubings, item 10 over the bonding-leads, item 11 and shrink them.
6
 Install at the door post as shown on Fig. A-GBDAB Sheet 03
 ,V i e wF :
2 Bonding-Lead E0090-10-125NN Item 11
1 Screw NAS1802-3-9 Item 9
1 Washer NAS1149C0332R Item 13
1 Washer F2529200920000 Item 14
NOTE
: The bonding lead length may be adapted by using next longer
bonding lead length if necessary.
7
 Attach the bonding-lead, item 11 to the wire protection as shown on Fig. A-
GBDAB Sheet 03
, View F with:
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
8
 Clean the bonding point at the web with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
9
 Attach the bonding-lead, item 11 to the web as shown on Fig. A-GBDAB
Sheet 05
,V i e wJw i t h :
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 43
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 54

@A340
SERVICE BULLETIN
10
 Apply to the Screw, item 12 and the nut, item 15 as shown on Fig. A-GBDAB
Sheet 05
,V i e wJ :
Varnish - Electrical
Bonding
04TMB2 As required
11
 Apply to the Screws, item 9 and 12 and the nut, item 15 as shown on Fig. A-
GBDAB Sheet 03
,V i e wF :
Varnish - Electrical
Bonding
04TMB2 As required
(b) Install the bonding-leads at the LH door post as follows:
1
 Remove as shown on Fig. A-GBDAB Sheet 04
 ,V i e wG :
1 Screw Item (1) Discard
2
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the diameter of the washer, item 14
as shown on Fig. A-GBDAB Sheet 04
 ,V i e wH .
3
 Make sure that there is no surface protection at the bonding point from the
bracket.
4
 Clean the bonding points at the wire protection, the bracket and the door post
with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
5
 Cut two pieces of tubing to a length of 0.085 m (3.35 in.) and one piece to a
length of 0.185 m (7.28 in.) from:
0.6 Tubing ABS0916B05 Item 10
6
 Push the tubings, item 10 over the bonding-leads, item 16, 21 and 22 and
shrink them.
7
 Install at the door post as shown on Fig. A-GBDAB Sheet 04
 ,V i e wH :
1 Bonding Lead E0090-10-100NN Item 16
1 Bonding Lead E0090-18-200NN Item 22
1 Screw NAS1802-3-9 Item 9
1 Washer NAS1149C0332R Item 13
1 Washer F2529200920000 Item 14
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 44
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 55

@A340
SERVICE BULLETIN
For operators with KITD01R04 get this item from COMPD01:
1 Bonding Lead E0090-18-200NN Item 22
NOTE
: The bonding lead length may be adapted by using next longer
bonding lead length if necessary.
8
 Attach the bonding-lead, item 22, to the bracket as shown on Fig. A-GBDAB
Sheet 04
,V i e wHw i t h :
1 Bonding Lead E0090-18-100NN Item 21
1 Screw NAS1802-08-7 Item 19
1 Washer NAS1149CN832R Item 20
For operators with KITD01R04 get these items from COMPD01:
1 Bonding Lead E0090-18-100NN Item 21
1 Screw NAS1802-08-7 Item 19
1 Washer NAS1149CN832R Item 20
9
 Attach the bonding-lead, item 21, to the wire protection as shown on Fig. A-
GBDAB Sheet 04
, View H with:
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
10
 Clean the bonding point at the web with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
11
 Attach the bonding-lead, item 16, to the web as shown on Fig. A-GBDAB
Sheet 05
,V i e wKw i t h :
1 Screw NAS1802-3-7 Item 12
1 Washer NAS1149C0332R Item 13
1 Nut NAS1726C3P Item 15
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 45
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 56

@A340
SERVICE BULLETIN
12
 Apply to the Screw, item 12 and the nut, item 15 as shown on Fig. A-GBDAB
Sheet 05
,V i e wK :
Varnish - Electrical
Bonding
04TMB2 As required
13
 Apply to the Screws, item 9 and 12 and the nut, item 15 as shown on Fig. A-
GBDAB Sheet 04
,V i e wH :
Varnish - Electrical
Bonding
04TMB2 As required
(c) Install the wire harness to the wire protection as shown on Fig. A-GBDAB Sheet
06
,V i e wL .
(d) Install the wire harness to the wire protection as shown on Fig. A-GBDAB Sheet
06
,V i e wL .
(e) Install the damper unit to the pelmet, refer to AMM Task 52-51-11-400-802.
(f) Make sure that cockpit door operates easily and closes correctly, refer to AMM
Task 52-51-11-820-801.
**CONF 003
(1) Subtask 254349-831-201-004 - Modify the Cockpit Door Frame Structure
Work Zones and Access Panels
Zone
 Access/Work location
220
Manpower Resources
Manhours
 3.50
Minimum number of person
 1
Subtask elapsed time
 3.50
Skills
 AIRFRAME
Material necessary to do the job
Kit 254349D02R02
ITEM
 NEW PART N˚
 QTY (UM)
 KEYWORD
 SEE
NOTES
1
 NAS1102-3-8
 2
 SCREW
2
 NAS1102-08-10
 6
 SCREW
5
 NAS1096-3-12
 1
 SCREW
6
 NSA5320-10
 1
 WASHER
7
 ABS1577D54
 1
 BRACKET
8
 ABS0547D503
 2
 RIVET
18
 F2529200700200
 6
 PLACARD
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 46
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 57

@A340
SERVICE BULLETIN
Consumable CMLD01
ITEM
 DESCRIPTION
 REFERENCE TO
CML MAT. No.
QTY PER A/C
 SEE
NOTES
Mineral Oil Base Grease
 03FAB1
 As required
Varnish - Electrical Bonding
 04TMB2
 As required
Polysulfide Sealant
 06AAB1
 As required
Non Aqueous Cleaner-
General
08BAA9
 As required
Textile-Lint Free Cotton
 14SBA1
 As required
References
Aircraft Maintenance Manual (AMM)
 Task 52-51-00-710-803
Task 52-51-15-000-801
Task 52-51-15-400-801
Illustrated Parts Catalog (IPC)
 52-51-01
Fig. A-GBAAA
Prepare the bonding points at the wire
protection
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBBAA
Install the bracket at the pelmet
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBCAA
Prepare the bonding points at the door
posts
Sheet 01
Sheet 02
Sheet 03
Fig. A-GBEAC
Prepare the bonding points at the webs
Sheet 01
Sheet 02
Sheet 03
(a) Remove the keypad from the gap cover, refer to AMM Task 52-51-15-000-801.
(b) Loosen the nuts and carefully remove the wire harness from the wire protection as
shown on Fig. A-GBAAA Sheet 02
 ,V i e wC .
(c) Modify the wire protection as follows:
1
 Prepare the bonding point at the front side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAA Sheet
03
,V i e wD .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAA Sheet 03
 ,V i e wD .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAA Sheet 03
,V i e wD .
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 47
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 58

@A340
SERVICE BULLETIN
2
 Prepare the bonding point at the upper side of the wire protection:
a
 Mark the position of the bonding point as shown on Fig. A-GBAAA Sheet
03
,V i e wE .
b
 Drill a pilot hole to a diameter of 2.5 mm (0.1 in.).
c
 Remove the metal surface protection to a diameter of 12.5 mm (0.49 in.)
as shown on Fig. A-GBAAA Sheet 03
 ,V i e wE .
d
 Drill the hole to a final diameter of 5.1 mm (0.2 in.) as shown on Fig. A-
GBAAA Sheet 03
,V i e wE .
3
 Clean the bonding points with:
Non Aqueous
Cleaner-General
08BAA9 As required
Textile-Lint Free
Cotton
14SBA1 As required
4
 Apply to the bonding points a thin coat of:
Mineral Oil Base
Grease
03FAB1 As required
NOTE
: The application of the grease is only necessary if you can
not install the bonding leads (SUBTASK 254349-831-202 004
Install Bonding-Leads to the Upper Cockpit Door Frame ) in
the next 4 hours.
5
 Install as shown on Fig. A-GBAAA Sheet 02
 ,V i e wC :
1 Placard F2529200700200 Item 18
(d) Modify the door posts as follows:
1
 Prepare the bonding point at the LH door post:
a
 Remove as shown on Fig. A-GBCAA Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAA Sheet 02
 ,V i e wF .
c
 Install as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 48
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 59

@A340
SERVICE BULLETIN
d
 Apply to the screw, item 1 as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
Varnish - Electrical
Bonding
04TMB2 As required
NOTE
: Bonding can be performed on other door post location
than shown in Fig. A-GBCAA Sheet 02
 if this lead to less
equipment removal. Bonding is to be performed at one
position with screw NAS1102-3-8 installed.
2
 Prepare the bonding points at the RH door post:
a
 Remove as shown on Fig. A-GBCAA Sheet 02
 ,V i e wE :
1 Screw Item (1) Discard
b
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the countersink diameter as
shown on Fig. A-GBCAA Sheet 02
 ,V i e wF .
c
 Install as shown on Fig. A-GBCAA Sheet 02
 ,V i e wF :
1 Screw NAS1102-3-8 Item 1
d
 Remove as shown on Fig. A-GBCAA Sheet 03
 ,V i e wG :
6 Screw Item (2) Discard
1 Gap Cover Item (3) Retain
1 Door Frame Panel Item (4) Retain
NOTE
: For the PN of the gap cover, item (3) and the door frame
panel, item (4), refer to IPC 52-51-01.
e
 Remove as shown on Fig. A-GBCAA Sheet 03
 ,V i e wH :
1 Screw Item (5) Discard
1 Washer Item (6) Discard
f
 Remove the surface protection around the screw hole to a diameter
approximately 3 mm (0.12 in.) larger than the screw head diameter as
shown on Fig. A-GBCAA Sheet 03
 ,V i e wJ .
g
 Install as shown on Fig. A-GBCAA Sheet 03
 ,V i e wJ :
1 Screw NAS1096-3-12 Item 5
1 Washer NSA5320-10 Item 6
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 49
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

### Page 60

@A340
SERVICE BULLETIN
h
 Apply to the screws, item 1 and 5 as shown on Fig. A-GBCAA Sheet 02
 ,
View F and Fig. A-GBCAA Sheet 03
 ,V i e wJ :
Varnish - Electrical
Bonding
04TMB2 As required
i
 Install as shown on Fig. A-GBCAA Sheet 03
 ,V i e wG :
1 Gap Cover Item (3) Retained at
removal
1 Door Frame Panel Item (4) Retained at
removal
6 Screw NAS1102-08-10 Item 2
3
 Install as shown on Fig. A-GBCAA Sheet 02
 , View C and D:
2 Placard F2529200700200 Item 18
(e) Install the bracket as follows:
1
 Remove the surface protection from the contact area of the bracket, item 7 to
the pelmet as shown on Fig. A-GBBAA Sheet 02
 ,V i e wD .
2
 Use the bracket, item 7 as template and mark the position of the holes as
shown on Fig. A-GBBAA Sheet 03
 ,V i e wE .
3
CAUTION
: MAKE SURE THAT YOU DO NOT DRILL TO MORE THAN
A DEPTH OF 21 MM (0.83 IN.) TO AVOID DAMAGE TO
THE S_GLASS ON THE CABIN SIDE.
Drill pilot holes to a diameter of 2.5 mm (0.098 in.) and a depth of 21 mm-1
mm (0.83 in.-0.039 in.).
4
 Drill the pilot holes to the final diameter of 4.1 mm (0.16 in.) and a depth of 21
mm-1 mm (0.83 in.-0.039 in.) as shown on Fig. A-GBBAA Sheet 03
 , Section
A-A.
5
 Deburr the holes.
6
 Remove the surface protection around the rivet holes to a diameter
approximately 3 mm (0.12 in.) larger than the rivet head diameter as shown on
Fig. A-GBBAA Sheet 02
 ,V i e wD .
7
 Clean the modification area with:
Non Aqueous
Cleaner-General
08BAA9 As required
DATE: May 28/14 SERVICE BULLETIN No.: A340-25-4349
REVISION No.: 02 - Sep 04/15 Page: 50
6
Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

The text continues at https://openairdocs.org/service-documents/airbus/a340-25-4349/file/9b4f687b18f7.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
